Refurbishment of Change room

Amount

Lead charges for 1st 1 KM or part thereof, by mechanical transport including loading unloading, stacking / levelling etc. For soil.

Lead charges for lead exceeding 4 KM not exceeding 5 KM, by mechanical transport including loading,unloading, stacking / levelling etc. Note: The rates in respect of this Item are applicable for NET Quantities arrived at after making deduction for voids @ 50% of the corresponding STACK / TRUCK Measurement. For soil.

Supplying and injecting with approved quality chemical emulsion at the rates and concentrations as per IS 6313-2001 Part II for preconstructional antitermite treatment and creating a chemical barrier under and alround the masonry pits, masonry foundations, wall trenches, plinth filling, junctions of wall and floor, expansion joints, surfaces of RCC works for a depth of min. 500 mm from the finished ground level, surrounding of pipes, conduits etc., walls retaining soil above floor level, apron and drain along the perimeter of the building including all byeworks complete as per specification / IS 6313:2001 or latest revision and direction of Engineer Incharge (only ground floor plinth area of the building will be measured for the payment in the following three stages. i) 20% after completion of the foundations ii) 50% after completion of the ground floor flooring iii) 30% after completion of all treatment works including ground floor doors & windows. Work to be executed by approved agency and specified guarantee for 10 (ten) years shall be furnished by the contractor.

Providing and laying in position cement concrete of 1:2:4 (1 cement, 2 crushed sand, 4 graded stone aggregate of nominal size, graded stone aggregate of maximum size 20) including consolidation, finishing, curing etc. complete as per specifications and drawings but excluding the cost of Form work shuttering, centering and steel reinforcement complete at all levels.

Providing and laying in position Reinforced Cement Concrete (RCC) of grade M-30 using 20mm maximum size aggregates and crushed sand of approved quality including admixtures of approved brand and quality (plasticiser or super plasticiser) if required, including weigh batching, mechanical mixing, transporting, placing, vibrating, consolidation, finishing, curing etc. complete but excluding the cost of centering, shuttering and reinforcement complete as per specifications up to Plinth Level.

Extra for RCC Using Ready Mix Concrete from outside project area including transporting and pumping from approved batching plants .

Providing Reinforcement Steel for reinforced cement concrete at all levels including supplying, preparation of bar bending schedules, cutting, bending, transporting, fixing, tying in position with PVC coated G.I binding wire, all labour charges, cost of cover blocks in specified grade of concrete etc. complete as per specifications and drawings. Steel supplied by the contractor. Using TMT bars of specified grades of all sizes. TMT bars to be supplied by the contractor from the own plants of SAIL, RINL or TATA make only using virgin materials

Providing, centering, shuttering Form work using steel plates, timber planks for all types of structures including necessary strutting, propping, staging, supports, bracings etc. and deshuttering the same after the specified time all as per drawings, specifications and as directed by the Engineer-in-charge at all levels. For Sub structures

Providing and constructing Half brick masonry using Fly ash/ Fly ash Lime bricks with minimum 70 kg / Sq.cm strength of approved make and size in partition walls in C.M 1:4 (using crushed sand) including scaffolding, raking out joints, curing etc. complete and with stiffners of RCC 1:2:4 (105 X 75 mm size) at every 900 mm height including form work curing etc. complete as per specifications but excluding reinforcement in Super Structure up to Floor - II level. (Reinforcement will be paid under relevant item)

Providing and constructing Brickwork in cement mortar 1:4 using crushed sand with Fly ash/ Fly ash Lime bricks with minimum 70 kg/ sq.cm strength of approved make and size in super structure up to and including Floor II Level including, scaffolding, raking out joints, curing, cleaning complete all as per specifications and drawings.

Providing and constructing Random Rubble masonry using approved Rubble stone in foundation and plinth in C.M 1:6 (using crushed sand) including raking out joints or simultaneous flush pointing below ground level / plinth level and up to and including 20 m height including scaffolding, curing etc. complete as per drawings and specifications.

Supplying , cutting to shape and fixing specified diameter UPVC pipes as per IS 4985 in RR Masonry/ RCC walls for weep holes complete all as per drawings and as specified at site. 110 mm dia UPVC Pipes

Providing 15 mm thick plastering using Ready mix internal plastering compound of approved make for internal faces of brickwork / concrete surfaces including preparation of the surface, curing, cleaning, scaffolding complete all as per specifications and as directed at site by the Engineer-in-charge

Providing 20 mm thick plastering using Ready mix external plastering compound of approved make for external faces of brickwork / concrete surfaces including preparation of the surface, curing, cleaning scaffolding up to 10 metres height complete.all as per specifications including forming drip moulds wherever necessary and as directed by the Engineer-in-charge

Providing and fixing G.I. chicken mesh in the junctions of concrete & brick work / masonry or as directed by the Engineer in charge including cutting, fixing with nails in position before plastering complete all as directed by the Engineer-in-charge. (only area of the chicken mesh used alone will be measured)

Providing and fixing Glazed VITRIFIED anti skid floor tiles of approved make in different sizes conforming to IS 15622 in all colours and shades in Glossy or Matt or satin finish laid over a bed of minimum 20 mm thick bed of cement mortar 1:4 (using Crushed sand) and jointing with grey cement slurry including grouting with the joints with white cement based Tile Grout of approved make and matching shade complete as per patterns, drawings and specifications complete as directed by the Engineer-in-charge. Using Tiles of size 600 X 600 mm or as per site condition with the approval of engineer-in-charge.

Supplying, stacking, and laying of 230mm thick Rubble stone soling using spotless stones as under floor base, below floor, foundations, and compacting, ramming including consolidation of blinding material, moorum , filling of stones vertically hand set, interstices packed with smaller stone chip, blinding with murrum, watering, consolidating & finishing to level etc. complete all as per specifications and as directed by the Engineer-in-Charge.

Labour charges for Murrum Filling under floors of specified thickness in layers of not exceeding 150 mm thickness including consolidation etc. complete (using Murrum available at BARC campus with a lead of up to 4 km)

Providing and fixing 1st quality approved make - Digital highlighter 300 x 600mm or as per site condition - wall tiles as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (using crushed sand), setting the tiles in cement slurry and pointing the joints with matching colour Tile grout compound of approved make of matching shade complete as per drawings, patterns and specifications complete as directed by the Engineer- in-charge

Providing and fixing 17 mm thick gang saw cut mirror polished (premoulded and prepolished) machine cut Granite of Jet black colour for kitchen platform, vanitiy corners, Wash basin Counters, Door Frames, window sills, facias, urinal partitions and similar locations of required size of approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (using crushed sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing the edges to give high gloss finish etc. complete at all levels as per specifications and as directed by engineer-in-charge.(Sample of Granite slab shall be got approved by the Engineer-in-charge).

Extra for providing edge moulding to 17 mm thick marble stone /Granite Slab counters, Vanities etc. including machine polishing to edge to give high gloss finish et. Complete as per design approved by Engineer-in-charge. For granite work

Providing and fixing anodized aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / Z sections and other sections of approved make conforming to IS 733 and IS 1285 fixed with rawl plugs and screws or with fixing clips or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / panelling, C.P brass / stainless screws all complete as per drawings and directions of Engineer-in-charge including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required filling the gaps using silicon grout sealant etc. (fittings glazing and panelling shall be paid for separately)

Providing wood work in frames of doors, windows, clear story openings and other frames, wrought framed and fixed in position of required size and shape including sawing, jointing, making rebates for shutters, making grooves as shown in the drawings, finishing the surfaces to the required finish all as per specifications and drawings including necessary MS hold fasts 40 mm X 3 mm thick, 200 mm long / with coach screws including protective painting to the surface that will come in contact with walls, joining materials, labour etc. complete all as per specifications and as directed by the Engineer-in-charge. Second class teak wood

Providing and fixing 35 mm thick flush door shutters conforming to IS : 2202 non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with internal teak wood lipping 25mm wide and fixing with 4 Nos of 125 mm long Stainless steel Hinges with S.S. wood screws complete.

Providing and fixing FRP door shutters flush door / panelled type with plain colour or wooden veneer finish of approved make, design & colour. made out of 1.5 mm thick FRP skin moulded over wooden frame work of 40 mm wide and required thickness wooden styles and minimum 100 mm wide lock rails and wooden blocks for door stoppers, tower bolts, baby latch, aldrop, handles etc. wherever required and core filled with Polyurethane Foam and fixing with 4 Nos 100 mm (ISI marked) stainless steel hinges with S.S. wood screws. using 35 mm thick panelled door type of approved colours including the cost of 100 mm ISI marked heavy quality stainless steel butt hinges with necessary screws.

Providing and fixing anodised aluminium aldrop ISI marked of size 300 X 16 mm transparent or dyed to required colour or shade with necessary screws etc. complete as directed by the Engineer- in-charge

Providing and fixing anodised aluminium tower bolts of size 300 X12 mm (barrel type) ISI marked of approved make transparent or dyed to required colour or shade with necessary screws etc.all as per specifications and as per drawings.

Providing and fixing brass mortise latch and lock of approved make with 6 levers and a pair of lever Brass handles with necessary screws etc complete suitable for fixing in wooden / steel/ FRP/ doors as per specifications.

Providing and fixing IS: 3564 marked aluminium die cast body tubular type universal hydraulic door closer of approved make with necessary accessories and screws etc. in wooden doors / steel doors with necessary bolts & nuts complete as per specifications and as directed by the Engineer-in-charge.

Providing and laying water proofing treatment in sunken portions of WCs, bath rooms etc. by applying cement slurry mixed with water proofing cement compound consisting of applying: (a) 1st layer of slurry of cement @ 0.488 kg / sq.m mixed with water proofing cement compound @ 0.253 kg per sq.m. including injecting cement slurry .This layer will be allowed to air cure for 4 hours. (b) 2nd layer of slurry of cement @ 0.242 kg / sq.m mixed with waterproofing cement compound @ 0.126 kg / sq.m. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with cement slurry. Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (using crushed sand) admixed with proprietary water proofing compound conforming to relevant IS and approved by Engineer-in-charge including mixing 'RECRON 3S' fibre at the rate of 125 grams per 50 kg of cement in top layer of plaster and finally finishing the surface with trowel with neat cement slurry in bottom and all the sides of sunken portion. complete as directed by the Engineer-in-charge. The treatment to be tested for water tightness before filling the sunken areas.

Providing and applying Wall painting with two coat with Premium plastic emulsion paint of approved brand (Asian or approved equivalent brand and manufacturer) to give an even shade including preparation of the surfaces, scaffolding a coat of approved cement primer, complete as directed by the Engineer-in-charge.

Providing and Painting two coats of synthetic enamel paint on Steel Surfaces of approved brand and manufacture to give an even shade without primer coat. including preparation of the surfaces, scaffolding complete. as per specifications and as directed by the Engineer-in-charge

Providing and painting over wooden surfaces with synthetic enamel paint of approved brand and manufacturer of required colour to give an even shade with two coats excluding wood primer including preparation of the surfaces, scaffolding complete. as per specifications and as directed by the Engineer-in- charge.

Providing and painting walls with (TWO coats) of approved shade of high build protective , elastomeric water proof exterior grade paint of approved make of required shade, minimum dry film thickness of 250 microns achieved in two or more coats / as per manufacturer's specifications including preparation of the surfaces by scrapping / wire brush , scaffolding complete. Primer coat will be with approved make with water in ratio of 1:2 and 2 coats of finishing coat without water all as directed by Engineer-in- charge.

Providing and applying white cement based wall putty of approved make over concrete or Plastered surface up to 3 mm thick to get uniform surface free from undulation including cleaning complete all as directed by the Engineer-in-charge

Providing and fixing double tubular scaffolding system using H?frames with cup lock type on the exterior side upto seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre horizontal and vertical tubes joining with cup and lock system with M.S. tubes, M.S. tube challies, M.S clamps and M.S staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connection with building etc. wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and as approved by the Engineer -in - charge. The elevational area of the scaffolding shall be measured for payment purposes. The payment shall be made once irrespective of duration of scaffolding

Dismantling plain cement concrete manually / by mechanical means carefully without damaging adjacent structures including disposal of debris within 200 m lead as per direction of Engineer-in charge

Dismantling brick work in Cement mortar carefully without damaging adjacent structures including stacking of materials and disposal of unserviceable materials within 100 m lead as per direction of Engineer-in-charge

Dismantling doors, windows and clear storey windows (steel /wood) shutter including chowkhats, architraves, holdfasts etc. complete and stacking within 100 m lead (full windows) of area 3.00 Sq.M and below

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 100 m lead For thickness of tiles above 10 mm and up to 25 mm

Dismantling Aluminium / Gypsum partitions, aluminium /wooden doors, windows, fixed glazing and false ceiling including disposal of unserviceable surplus material and stacking of serviceable materials within 100 m lead as directed by the Engineer-in-charge

Dismantling G.I pipes of all diameter external work including excavation and refilling trenches after taking out pipes manually / by mechanical means including stacking of pipes within 100 m lead as per direction of Engineer-in-charge

Dismantling the following dia of C.I pipes including excavation, taking out the pipes manually / by mechanical means, breaking lead caulked joints, melting of lead, making into blocks including stacking of pipes within a lead of 200 m as per direction of Engineer-in-charge. 75 mm Dia C. I pipe

75 mm Dia to 200 mm Dia C. I pipe

150 mm Dia to 200 mm Dia C. I pipe

Dismantling flushing cistern, wash basin, urinal, EWC, Geyser, mirror of any size including stacking of useful materials near the site and disposal of unserviceable materials within 100 m lead

Dismantling old plaster / skirting carefully , raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 100 m lead

Lead charges for lead Exceeding 4 KM not exceeding 5 KM, by mechanical transport includinmg loading,unloading, stacking / levelling etc. For Debris beyond 4 Km but up to and including 5 Km. Note: The rates in respect of this Item is applicable for NET Quantities arrived at after making deduction for voids @ 30% from corresponding TRUCK Measurement

Providing and laying 80 mm thick factory made cement concrete interlocking paver block of M-35 grade made by block making machines with strong vibratory compaction and approved size, shape, design laid in required colour and pattern over and including 150 mm thick compacted bed of stone dust / Murrum, filling the joints with crushed sand etc. all complete as -per the direction of the Engineer-in-charge

Providing structural repairs in old damaged concrete structures / surfaces with approved Polymer with following operations 1) Removal of loose/Spalled or damaged concrete by chipping and cleaning the concrete surface and reinforcement steel with wire brush and with water 2) Cleaning the re bars with Acetone for complete rust removal and washing with water to make the surface clean. 3) Applying protective coat / bond coat using polymer and cement in the proportion of 1; 1.5 (1 part of polymer and 1.5 parts of cement in synthetic enamel paint like consistency with brush 4) Reinstate the area with polymer modified mortar in layers of maximum 20 mm with the proportion of Cement 50 Kg : washed and dried river sand 87.50 kg ; silica sand 37.50 Kg. mixed with 10 litres of Polymer (or 1 Kg cement : 1.75 kg washed and dried river sand ; 0.75 Kg silica sand : 200 ml polymer) 5) If thickness of repair exceeds 20mm , after every 20 mm thick repair, bond coat as per 2 above to be applied and further thick of repair to be continued for each layer. This work is inclusive of all materials, labour, complete all as directed at site using approved polymer suitable for structural repair shall be used) Note: Scaffolding will be paid separately under relevant item,if applicable as decided by Engineer-in-Charge.

Providing , Laying , jointing, fixing and testing Heavy quality (C- Class) Galvanised Iron pipes and ISI marked fittings like, tees, elbows, bends, unions, nipples, reducers (Including weldable fittings, If required) etc. as required for the work, including testing the pipes and fittings for 10.00 Kg / Sq.Cm hydraulic pressure with a minimum period of two hours duration with clean water, including cutting , threading, welding, jointing with hemp yarn, white lead, jointing Teflon tape, exposed / concealed by chasing walls and making good by filling with concrete 1:3:6, complete all as per specifications and drawings, including two coats of anti corrosive bitumastic paint for all concealed lines / two coats of synthetic enamel paint for all exposed lines all as directed by the Engineer-in-charge. Pipes with exclusive use of TATA make C-Class pipes (For Item no. 50.6 Pipes with ISI marked 'C' -Class heavy quality pipes of approved make).

15 mm dia G.I pipes with C-Class TATA pipes

20 mm dia G.I pipes with C-Class TATA pipes

25 mm dia G.I pipes with C-Class TATA pipes

32 mm dia G.I pipes with C-Class TATA pipes

50 mm dia G.I pipes with C-Class TATA pipes

100 mm dia G.I pipes Pipes with ISI marked 'C' -Class heavy quality pipes of approved make.

Providing & fixing in position heavy pattern screw down gun metal gate valve with handles and wheels of approved make including testing for 10Kg/cm2 pressure with clean and potable water with a minimum testing duration of two hours etc.as per specification and as directed by the Engineer-in-charge

Providing and fixing 15mm dia. C.P Brass Bib cock of Heavy Quality of specified / approved make as per specifications and as directed by the Project Engineer (Samples to be got approved by the Project Engineer) 15 mm dia Bib cock Jaquar continental model or approved Equivalent type and make .

Providing and fixing C.P Brass Open Stop cock of Heavy Quality of specified / approved make as per specifications and as directed by the Project Engineer (Samples to be got approved by the Project Engineer). 15 mm/20mm n.b. CP Brass open stop cock Jaguar continential model or ESSCO / PLATO make or approved make

15 mm n.b. CP Brass open stop cock of approved make and type

20 mm n.b. CP brass open stop cock of approved make and type

Providing and fixing 15 mm n.b. CP brass Angle cock of approved make of heavy quality of specified / approved make, for wash basin inlet / flush cistern etc. as per specifications and as directed by the Engineer-in-charge

Providing and fixing PVC inlet connection pipes heavy quality suitable for hot and cold including CP brass unions and nuts 15 mm dia 600 mm long

Providing and Fixing CP brass 100 mm dia shower rose of Specified make as per specifications and as directed by Engineer-in-charge complete

Providing and fixing Heavy Quality 15 mm C.P brass pillar cock of approved make quarter turn and type as per specifications and as directed by the Engineer-in-charge.

Providing and fixing square mouth S.W. gully trap grade 'A' complete with CI grating brick masonry chamber with water tight CI cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4.5 kg and frame to be not less than 2.70 kg as per standard design. size : 150 x 100 mm Gully Trap "P" type.

Providing and laying non pressure NP2 class RCC Hume pipes of approved make, with collars jointed with stiff mixture of cement mortar in the proportion of 1:2, laying to the levels, slopes and as per the drawings and specifications and as directed by the Engineer-in-charge including testing of joints etc. complete.

250 mm Dia RCC Hume pipe class Np2

300 mm Dia RCC Hume pipe class Np2

Providing and constructing Inspection chambers of Internal size clear dimension of 900 x 600 mm in 230 thick brick masonry with cement mortar 1:4 over a bed of 150 mm thick 1:4:8 cement concrete foundation, plastering with cement mortar 1:4 20 mm thick on inside, out side and all exposed surfaces finished with a floating coat of neat cement, brick corbelling at top to provide opening of 900 X 450 mm, embedding the frame and cover with CC 1:2:4 concrete, and fixing cast iron steps if necessary at 300mm intervals complete . Depth of chamber not exceeding 900 mm. (excavation, soling, cast iron cover and C.I steps will be paid separately under relevant item)

Supplying and fixing Cast Iron Man hole or Cast Iron Steps cover of approved make and weight as specified in the drawings or as directed by the Engineer in charge.

Providing, supplying, fixing in position, under floors or in walls sand cast iron pipes including required specials like bends, tees, 'Y' collars, cowl etc for soil, waste and ventilation pipes conforming to IS 1729 of approved make including cost of jointing with spun yarn and molten lead of specified quantity, caulking the joints, including testing of pipes, painting with primer, fixing at walls with necessary approved type of clamps and brackets complete all as per drawings and specifications and as directed at site.

75 mm dia Sand cast iron S&S pipe as per IS:1729 with 0.90 kg lead / joint

100 mm dia Sand cast iron S&S pipe as per IS:1729 with 1.00 kg lead / joint

150 mm dia Sand cast iron S&S pipe as per IS:1729 with 1.00 kg lead / joint

Providing and fixing cast iron nahani trap / floor trap of 100 mm inlet and 75 mm outlet, (weighing 5.80 Kg each), jointing with lead with the connection pipes, placing as per the drawings, embedding in cement concrete 1:2: 4 and making circular hole up to floor level using 110 mm O/D PVC pipes of 6 Kg / sq.cm pressure and fixing 1 No 125 mm dia C. P brass grating , complete all as specifications and drawings and as directed by the Engineer-in- charge

Providing and fixing heavy quality stainless steel / C.P brass grating of approved equivalent make as specified for floor traps / nahani traps all as directed by the Engineer-in-charge SS grating 150 mm square with frame

Providing and fixing Chinaware Half round Urinal channel 100 / 150 mm dia with or without dead ends set in C.M 1:3 laid to proper slope & grade including finishing the joints with polymer based tile grout mix as per drawing and as directed by the Engineer-in- charge.

Providing and fixing Indian water closet (Orissa pan) with 100 mm China ware P or S trap, Flushing arrangements with 32 mm flush valve of approved make with necessary fittings , with all connections complete including chasing if necessary and making good, cleaning and commissioning all as per specifications and drawings and as directed. by the Engineer-in-charge. (Only 32 mm/40 mm dia G.I. line required for Metropole flush valve water supply will be measured and paid separately under relevant Item). White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests with 32mm Metropole flush valve of approved make.

Providing and fixing white vitreous China universal pedestal type water closet (Anglo Indian type W.C. pan) with seat and lid, 10 litre low level white PVC flushing cistern with manually controlled device (handle lever) conforming to IS:7231, flush bend, fixing EWC with C.P brass screws, 15 mm PVC heavy quality inlet connection of 450 mm long, including testing , commissioning & cleaning etc. complete all as per drawings and specifications and as directed by the Engineer-in-charge. Including dismantling of water closet of any size including stacking of useful materials near the site and disposal of unserviceable materials within 100 m lead.

Providing and fixing white vitreous china flat back half stall urinal size 580x380x350 mm / 610 mm of approved make Aquaseal model with Push cock of approved make, with CP brass flush pipe unions, heavy quality C.P. brass spreaders, C.P waste coupling with dome grating, clamps complete all as per specifications drawings and as directed by the Engineer-in-charge. Including dismantling of urinals of any size including stacking of useful materials near the site and disposal of unserviceable materials within 100 m lead.

Providing and fixing vitreous China wash basin of approved make and colour with C.I. brackets, 15 m C.P. brass pillar tap of approved make,15 mm x 600mm long PVC Inlet connection, 32mm heavy quality C.P. brass waste coupling of standard pattern, including painting of fittings and brackets, cutting and making good the walls and testing complete all as per specifications and as directed by the Engineer-in-charge. Ordinary colour range vitreous China wash basin size 630 x 450 mm and equivalent sizes with single 15 mm C.P. brass pillar tap.

Providing and fixing PVC low level / high level flushing cistern 10 litre capacity of approved make in white colour with flush pipe with manually controlled device (handle lever) conforming to IS:7231, with all fittings and fixtures etc. complete as per specifications and as directed by the Engineer-in-charge.

Providing and fixing 6 mm thick mirrors of size approved make with bevelled edges complete 600 x 450 mm of with 6 mm thick asbestos sheet back ground fixed to walls with C.P. brass screws and concealed washers complete, providing and fixing mirrors with approved make stainless steel 304 grade STUDS (with wall spacers) complete all. all as per specifications and as directed by the Engineer-in-charge .

Providing and fixing heavy quality CP brass bottle trap 31 / 32 mm of approved make single piece moulded with height of 270mm, effective length of tail pipe 260 mm from the centre of the waste coupling 77 mm breadth with 25 mm minimum water seal, of approved make for wash basins / urinal etc all as per specifications and directed by the Engineer in charge.

Providing and fixing C.P brass towel rail of approved make 600 mm long complete fixed to walls with 30 mm CP brass screws with concealed fitting arrangement all as directed by the Engineer-in- charge.

Providing and fixing Brass 15 mm C.P presstomatic series auto shut urinal flush cock of approved make and quality

Providing, supplying and fixing jet spray with 1.00 metre long flexible tube connection in European / Anglo Indian closet under seat cover fixtures complete all as specified and as directed by the Engineer-in-charge

Fixing of Nozzles @ 500 mm c/c in grid pattern using suitable drill machine up to 100 mm in depth/ surface Noszzles as per site conditions and as directed and sealing the Noszzles to facilitate epoxy grouting.

Injection of low viscosity Epoxy Injection Grout - two components low viscous high strength (7 days comp strength 800 kg/sqcm) epoxy resin based injection grout complies with BS 6319 / ASTM C -881 or Dr. Fixit or BASF/SIKA/ Huntsman or approved equivalent make through the above Noszzles to fill the cracks/ voids using compressor machine as per manufacturetres specification, actual site requirements and as directed at site.

Providing and supplying foot operated value with spout type pillar tap with all accessories & fittings as per specifications and as directed by the Engineer-in-charge, PVC flexible connection pipes 2 nos. of 1.5m length.

Designing, providing and fixing of 4 mm thick approved make and shade Aluminium Composite Metal Panel of approved make cladding at different locations including soffits of over-hangs and including aluminium frame work with grids filled in with weather silicon sealant as per the drawings. The ACM panel composition shall be of 0.5 mm thick PVDF coated aluminium sheet + 3 mm thick low density polyethelene virgin resin core + 0.5 mm thick polyester (PVDF) coated Aluminium sheet all complete as per approved shop drawings and specification Note : ACMP shall be measured to the actual visible area of the ACP sheet including silicon joints as fixed on site.

Supply, installation, testing and commissioning of 6" NB size cast steel Gate Valve, ANSI pressure class 150 flanged end connection confirming to ASME B16.5, class 150, raising stem type, confirming to BS:1414/API:600

RESHMA CONSTRUCTION (BID ID -3246744)

S.B.Pawar Sairam Contractors (BID ID -3246691)