SPECIAL REPAIR TO SINGLE JCOS LIVING 39 NOS OF 505 ABW UNDER GE NORTH DELHI CANTT 10

Amount

M&L for providing PMM (Polymer modified cementitious mortar) :- (i) Dry sub strate surface and free of debris & dust (ii) Applying Epoxy bond coat on the sound substrate using approved spray machine & ensuring that no pin holes are visible.(In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes). (iii) Immediately after application of epoxy bond coat as above apply PMM (Polymer modified cementitious mortar) of 25 mm thickness. Note : Application of PMM shall be preferably be in coats of appx 10mm thickness. PMM work shall be executed in fairely rapid successions so as entire work is completed with in 30 mins). PMM shall be pre packed ready to use. (iv) PMM surface to be moist cured for three days followed by air curing in temperature as recommended by manufactuer complete all as specified and directed.

M&L for chipping of spalled and loose concrete and cleaning rust from re-inforcement by use of antirust chemical concrete surfaces with wire brushes cleaning with water allowed to dry applying a layer of zinc rich epoxy primer as antirust on all exposed reinforcement followed by a layer of bonding coat of a layer of epoxy adehessive on complete exposed surfaces of concrete and provide guniting in two layers over steel welded mesh 2 mm dia of wire and total aperture 75 mm, thickness of gunite n.exc 25 mm thick (average thickness) using cement mortar 1 :3 with OPC 43 grade cement mixed with polycrete admixture @ 2 % by wight of cement or as per manufactures instructions and finally applying cement plaster over gunite surfaces of required thickness to give an even uniform and smooth finish conforming to proper Geometrics in cement mortar 1:4 to match with the existing surface as in side and soffits of slabs,chajjas,fins,facias ,parapets ,columns and beams etc complete including necessary scaffolding ,shuttering necessary chased to brick work or RCC members at any height upto four storey buildings incl removing of small trees shrubs etc all as specified(Note: steel welded mesh to be welded with the existing reinforcement. The cost of wire mesh is to be welded with the existing re-inforcement is deemed to be included in the quoted rate complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) of wooden/steel n.exc 1.5 sqm, complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) of wooden/steel exc 1.5 sqm but n.exc 4 sqm each, complete all as specified and directed.

Taking down shutters of any description exc 1 sqm and n. exc 2 sqm each, complete all as specified and directed.

S & F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube, fixing in opening as per specification and directed.

S&F factory made solid panel PVC door shutter 30mm thick (stiles) consisting of frame made cut of M.S tubes for top & bottom rails; M.S frame shall be covered with heat moulded plain colour PVC ‘C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on other side and as gap inserted for top rail & bottom rail , panelling of plain colour PVC sheet to be fitted in the MS frame welded /sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, fixing in the frame at site as per specification and drawing.

S&F rolled section as in framing for door/vent/CB chowkhats and the like fixed with angle cleat and connecting plates incluidng welding 3 Nos MS butt hinges 100mm & 01 No 50mm complete (Butt hinges shall be measured and paid for separately).

Preparing surfaces of wood and wood based materials, steel and iron work, new or old,of any description and girth,not otherwise described, andtreated with tar or coal tar black paint treating ends of posts, backs of chowkats, etc., area tarred exc 0.1 sq. m but n exc 0.5 sq. m each, complete all as specified and directed.

S&F 30mm thick 2nd class glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc(with out sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, gauze etc size of members as specified in SSR part-I, section 8, clause 8.24(a), complete all as specified and directed by Engr-in-Charge.

S&F 35mm thick 2nd class plain framed, panelled shutter factory made (two panel) with lock rail and panel of 9mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated, complete all as specified and directed by Engr-in-Charge.

S & F Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aparture 1.40mm Fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.

S & F in repair stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aparture 1.40mm Fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.

M & L mild steel flat iron (25x3)mm for hold fasts complete welded complete confirming to FE-290 Gde- E-165 all as specified and directed.

S & F butt hinges 100mm size Medium weight cold rolled mild steel fixed complete all as specified.

S & F butt hinges 75 mm size Medium weight cold rolled mild steel fixed complete all as specified.

S&F aluminium alloy, anodised, sliding door bolts with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section etc length of bolt 250 mm, complete all as specified and directed .

S&F aluminium anodised barrel tower bolts of extruded section 150 mm long, complete all as specified and directed.

S&F aluminium alloy handles anodised, fabricated type of size 150 mm, complete all as specified and directed

S&F in repairs MS 300 long ordinary rat rail rod pattern spring including roller and roller plate complete all as specified and directed.

S&F 20 mm dia stainless steel drapary curtain road bright finish with bibs, bracket & internal funnels. complete all as specified.

S&F continous MS CP piano type hinges 30 mm flap (when opened), bright finish or electro galavanised complete all as specified and directed.

M&L for PCC (1:2:4 ) type B-1 ( using 20 mm graded stone aggregate ) as in bed blocks for fixing hold fasts of doors and windows frame complete all as specified and directed by engr-in-charge.

M&L for preparation of old wooden surfaces exc 10 cm width or girth and applying one coats of synthetic enamel paint, complete all as specified directed (Note:- Finish the surface without brush marks).

M&L for preparation of new wooden surfaces exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

M&L for preparation of new steel surfaces exc 10 cm width or girth and applying two coats of sysnthetic enamel paint over a coat of red oxide zinc chorme primer.

Demolition of cement concrete (unreinforced) in ground floor and in paving not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed.

M/L PCC 1:4:8, type D2, using 40 mm graded aggregate 75 mm thick as in sub floor, Sub base, floor complete all as specified & directed.

M&L chequered cement concrete tiles 20 cm x 20 cm x 25 cm thick with gray cement and no pigment set jointed and pointed in neat cement slurry in floor over 15 mm thick screed bed of CM 1:6 complete all as specified.

M&L for machine cut kota stone slab flooring 18-20 mm thick over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing with screed bed or bedding layer of mortar 20 mm thick in cement mortar 1:4 laying floor finishes complete all as specified.

M&L for machine cut kota stone slab flooring 18-20 mm thick in riser of steps, skirting, dedo and pillar laid over over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing with 15 mm thick of CM (1:3) screed bed including taking down cement plaster complete all as specified and directed by Engr-in-Charge

S&F in repair 110 mm bore PVC (SWR) Pipes single socket, in any length with rubber ring, joints fixed to walls or in any position complete all as specified and directed.

S&F PVC(SWR) bends plain 110mm bore complete all as specifed and directed.

Dismantling cast iron pipe & reinforced concrete drain pipes, jointed in cement mortar or any dia upto 100 mm alll as specified.

S&F cast iron soil, waste and vent pipes (sand cast) 100 mm bore in any length with or without ears with cement joints fixed to walls duly apply a coat of bitumenous black paint complete all as specified and directed

S&F cast iron soil, waste and vent pipes (sand cast) 75 mm bore in any length with or without ears with cement joints fixed to walls duly apply a coat of bitumenous black paint complete all as specified and directed

S&F cast iron soil, waste and vent pipes (sand cast) 100 mm bore in any length with or without ears with cement joints laid in trenches or in floors complete all as specified and directed

S&F cast iron soil, waste and vent pipes (sand cast) 75 mm bore in any length with or without ears with cement joints laid in trenches or in floors complete all as specified and directed.

S&F 100 mm bore CI bends any radius with ducks foot or heal rest, complete all as specified.

S&F in repair 150X150mm Salt-glazed stoneware gully traps, square or round mouthed, type 'P', complete all as specified.

S&F cast iron bend (any radius), diminishing pieces or tapers 75 mm bore fitted with oval access door, complete all as specified.

S&F stack clamps made out of 50 mm by 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stay to wall or roof for 100/110 mm bore pipe complete all as specified and directed.

S&F stack clamps made out of 50 mm any 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stay to wall or roof for 75 mm bore pipe complete all as specified and directed.

S&F cast iron branch pices single (equal enequal ordinary or inverted ( spigot or socketed type) or with paralled branches 75 mm bore with oval access doors complete all as specified and directed.

S&F cast iron branch pices single (equal enequal ordinary or inverted ( spigot or socketed type) or with paralled branches 100 mm bore with oval access doors complete all as specified and directed.

S&F cast iron vent cowl for 75 mm dia pipe all as specified and directed.

S&F cast iron floor trap 75 mm with grating including jointing to waste pipe fixed in cement concrete type B1 1:2:4 all as specified and directed.

Demolition of brick work including all quoins, arches, pillars, etc built in cement mortar, complete all as specified.

M&L for brick work in CM (1:6) straight or curved on plan exc 6.0m mean radius and using old size sub class 'B' bricks all as specified.

All as per item No 49 above but except bricks.

M&L for Brick wor with sub-class "B' Bricks straight or curved on plan to any radius in half brick thick wall built in CM (1:4) complete all as specified.

Taking down cement plaster of any description & thickness from brick/concrete sufaces of wall/ceiling etc including racking out joints, hacking for keys scrubbing down with water etc, complete all as specified.

M&L for rendering 15 mm thick in CM 1:6 on unfair faces of bricks work or concrete surfaces finished even and fair without using extra cement

M&L for 10 mm thick cement plaster in CM (1:3) as in ceiling finishing even and fair with out using extra cement complete all as specified.

M&L for 15 mm thick cement plaster in CM (1:4) on fair faces of brick work or concrete surfaces finished even and fair without using extra cement complete all as specified.

Supply only integral water proofing compound

M & L washing stone grit plaster on exterior walls in two layers, under 12mm cement plaster 1:4 (1 cement : 4 course sand)furrowing the under layer with scratching tool applying cement slurry on the under layer @ 3kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1cement: 1/2 course sand: 2 stone chipping 10mm nominal size) in panels with groove all around as per approved patteren including scrubing and washing the top layer with brushes and water to expose the stone chippinngs complete all as specified and directed.

M&L for preparing newly plastered surfaces of ceilling and applying three coats of white wash complete all as specified.

M&L preparation of newly plasterred sufaces of walls and applying two coats of cement base paint over a coat of primer complete all as specified.

M&L preparation of newly plastered surface on walls and applying 2 coat of OBD over a coat of chalk whiting complete all as specified.

M&L for preparing old plastered surfaces of ceilling and applying two coats of white wash incl complete removal of exiting treatment etc complete all as specified.

M&L preparation of old plastered surfaces of walls and applying two coats of cement base paint complete all as specified .

M&L for 25 mm thick cement concrete 1:2:4 type B-0 using 12.5 mm graded crushed stone aggregats as in correction layer of flooring and finished even and fair complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

M&L for coloured ceramic joint free tiles 7 to 8 mm thick 400 mm x 400 mm size of approved colour, as in floors etc, set, jointed in cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 15 mm thick screed bed in CM 1:6 etc compete as in flooring all as specified and directed.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface including 15mmthick screed bed in CM 1:4 complete all as specified and directed by Engr-in-Charge.

M & L for glazed coloured ceramic tile in dado/vertical surface (350mmx250mmx7mm/ 450x350x7mm) thick setand jointed in neat cement slurry and pointed in coloured cement to match the surface complete all as specifed and directed by Engr-in-charge.

M&L for 10mm thick rendering as backing coat on fair faces of brick/concrete surface in cement mortar 1:4 and rough finished on vertical surfaces complete all as specifed and directed by Engr-in-charge.

M & L for glazed coloured ceramic tile in skirting, including 10mm thick rendering in CM 1:3 even on fair faces of brick work including taking down cement plaster complete all as specifed and directed by Engr-in-charge.

S & F steel window box type made out of 16 guage steel section for frames and shutter as per drawing No. TD A sheet 01/03 to 03/03 with openable both glass and guage shutter including pintel hinges 75mm long , 12mm dia, 100mm long handle and tower bolt 150mm long , MS hooks & eye 150mm long complete all as specifed and directed by Engr-in-charge. (Glass & wire mesh shall be paid separately.

S & F steel ventilator box type made out of 16 guage steel section for frames and shutter as per drawing No. TD A sheet 01/03 to 03/03 with openable both glass and guage shutter including pintel hinges 75mm long , 12mm dia, 100mm long handle and tower bolt 150mm long , MS hooks & eye 150mm long complete all as specifed and directed by Engr-in-charge. (Glass & wire mesh shall be paid separately).

Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and /or riveted or forged in to spikesm frame guard bar, barred iron doors, ldder, framed balsters, railing, frame work for water tanks and similar works confirming to FE 290 Gd E-165 all as specified.

Dismantling and taking down of water storage tank capacity 250 ltrs to 500 ltrs of PVC, steel or RCC etc.

Supply and fixed rotational moulded polyetylene tripple layered water storage tanks (cylindrical vertical with closed top) of 500 Litres capacity hoisted and fixed in position and connecting up pipes securing access covers all as specified and directed

S & F ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (Min wt 210 gm each) for 20mm bore of pipe.

S&F in repairs gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed bore of pipe 15 mm complete all as specified & directed.

S&F in repairs gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed bore of pipe 20 mm complete all as specified & directed.

Taking up or down steel water tubing and connections including cleaning for refixing or removal from site 20mm bore pipe.

Taking up or down steel water tubing and connections including cleaning for refixing or removal from site 15 mm bore pipe.

M&L 15mm bore GI tubing medium grade with all fittings and fixed complete to walls, ceiling or laid in floor.

M&L 20mm bore GI tubing medium grade with all fittings and fixed complete to walls, ceiling or laid in floor.

Refixing of old steel tubing and connections in new or old position ( wall/floor/ceilings etc ) of size 15 mm bore

Refixing of old steel tubing and connections in new or old position ( wall/floor/ceilings etc ) of size 20 mm bore

S & F in repair 15mm bore dia CP bib cock fancy type cast copper alloy, screwed down high pressurewith cruch or butterfly handle, screwed one end of iron pipe or for union and fixed.

S & F in repair 15mm bore dia CP stop valve cast copper alloy, screwed down high pressure with cruch or butterfly handle, screwed one end of iron pipe or for union and fixed.

S & F in repair 15mm bore dia CP angle valve cast copper aloyes, screwed down high pressure with cruch or butterfly handle, screwed one end of iron pipe or for union and fixed.

S & F shower rose fancy type brass chromium plated 125mm heavy duty pattern with swivel joints screwed for 15mm bore including jointing to pipe or unions dle, screwed one end of iron pipe or for union complete all as specified & directed.

S&F in repair Vitreous china wash down water closet pan (pedestal pattern), white including fixing bolts, flushing cistern and flush pipe connection to trap and to flushing pipe including provn of cement concrete beading complete all as specified and directed.

S&F EWC seat cover black colour of PVC complete all as specified & directed.

S&F PVC low level flushing cistern 10 ltrs capacity incl PVC float valves, PVC connection and out let pipes complete.

S & F in Vitreous china wash basin white, flat back size 550x400mm excluding tap, chain, plug but including brackets, waste fitting 32mm dia, brass chromiun plated for glazed ware sink,basin, with long screwed sanks and fly nuts flange end bedded in red lead cement and other end fixed complete all as specified & directed.

S & F in repair PVC connections 15mm size with PTMT nuts of length 450mm

S & F 15mm CP mixer suitable for WHB for fixing hot and cold water screwed down for iron pipe and fixed all as specified & directed.

S&F in repair Tubular towel rail 600mm long of 20mm chromium plated brass screws and wooden/plastic cleats complete all as specifed and directed.

S &F in repair PVC waste pipe for WHB of bore 32mm complete all as specified & directed.

S & F soap dish vitrous china white 160x160x90mm fix to wall with brass screw complete all as specified & directed.

Dismantling of brick (laid flat or on edge) or brick tile in floor chennals, kerbs, apron etc (each layer) laid, bedded and pointed in any mortar complete all as specified.

Demolition of mud in roof, any thickness, including plastering and leaping (what ever full thickness removed or only or part therefore).

M & L Roughening surface of old concrete surfaces by picking sweeping, cleaning and washing down with water to remove dust etc and brushing neat cement slurry with 3kg cement per Sqm including taking down tarfelt etc complete all as specified.

M & L PCC 1:2:4, type B1 using 20mm graded stone agg as in slope for roof, coping bending rounded or chamfered on edges complete all as secified and directed.

M & L for Water proofing treatment to RCC roof slab, walls, chhajjas etc, shall be carried out as specified below and as directed by Engineer-in-Charge. (a) M&L for 15mm thick plaster screed bed layer in CM 1:3 on concrete surfaces. (b) Preparing plastered surfaces of roof slab, walls, chhajjas etc, by brooming with broom sweeping free from dirt dust etc & evenly applying a coat of approved bituminous primer @ 0.20 Kg/Sqm of area complete all as specified. (c) Laying APP polymer modified approved membrane, non woven, polyester, weighing not less than 3.5 Kg/Sqm with laps & overlaps as specified & joints sealed and applied complete by torch application method all as specified & directed by Engr-in-Charge. Carrying out test by flooding water for 24 hrs for leakage & seepages and rectifying the same to the entire satisfaction of GE. (d) Finally applying a coat of solar reflective bituminous aluminium paint @ 0.15 ltr/Sqm on the top of membrane surfaces complete all as specified & as directed by Engr in Charge

Cutting channels, grooves or rebates n exc 15cm girth, and trimming surface with or without reinforcement all as specified by Engineer-in-Charge.

S&F SFRC manhole covers and frame medium duty of overal size 600mmX600mmX80 mm thick, factory made and test load 10 tonnes (MD-10), strength as per IS: 1726-1991 all as specified by Engineer-in-Charge.

S&F steel peg set colour coated of six as per sample approved by GE

S & F in repair for 18/19mm thick one side decorative lamination and other side balancing white sheet consisting of carcass 18/ 19mm thick PVC sheet including 6mm thick one side decorative and other side balancing white sheet and 20mm wide and 1mm thick PVC EDGE Bending pasted to edges of PVC board with approved adhesive and self tapping screws all as specified and directed.

S&F sheet glass ordinary quality, 3mm thick and glazing with oil putty in square n.exc. 0.5 Sqm in each pane.

S & F 3 mm thick figured glass pin head type and glazing with oil putty n exc 0.5 Sqm in each pane.

Moulding of kota stone/marble stone full round complete all as specified.

M & L numbering tiles of size 100x200mm duly marked with letters and numbers with paint and fixed in CM (1:4) for numbering of bldgs all as directed and specified.

Taking down carefully copper / aluminium point wiring (light / fan socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc for taking credit including making good the disturbed surfaces to match with the existing all as specified and directed.

Material & labour for point wiring with 1.5 Sq.mm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed FRLS copper conductor cable with and including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 20mm dia or higher, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall on wall including sunk zinc coated pressed steel terminal box of 1.60mm thick with 3mm thick plastic laminated sheet top cover, brass screws, cup washers etc complete all as specified and directed for One light / bell / buzzer point controlled by one, one way switch 06 Amps, all as specified and directed.

All as per srl item No- 112 here-in-before but for one light point controlled by two way switches complete.

All as per srl item No- 112 here-in-before but one fan point controlled by one, one way switch 06 Amps.

All as per srl item No- 112 here-in-before but one 3 pin, 06 Amps socket outlet point on independent board controlled by one, one way 06 Amps switch.

All as per srl item No-112 here-in-before but one 3 pin, 06 Amps socket outlet point on same board controlled by one, one way 06 Amps switch.

All as per Serial Item No-112 above but point wiring with 4 Sqmm single core FRLS cables and earth continuity wire of 4 Sq mm single core FRLS cable for one 3 pin 15 Amps socket out let point controlled by one, one way switch on independent board complete all as specified and directed.

S&F bell push, flush type, 06 Amps, 230 volts with switch frame complete.

Supply & fixing switch piano flush type, 06 Amps, single pole, one way, 250 volts complete all as specified & directed.

Supply & fixing switch piano flush type, 16 Amps, single pole, one way, 250 volts with switch frame complete all as specified & directed.

Supply & fixing socket outlet 2 in 1, 5 pin, 06 Amps, flush type, 250 volts with socket frame complete all as specified & directed.

Supply & fixing socket outlet 2 in 1, 3 pin, 06 Amps and 3 pin, 16 Amps, flush type, 250 volts with socket frame complete all as specified & directed.

Supply and fixing ceiling fan regulator, stepped type of 0 to 04 rotary steps, electronic, 02 module, humfree, AC, 230 volts, 100 watts, duly ISI marked complete all as specified & directed.

Supply and fixing ceiling rose, 6 Amps, 250 volts, AC, ISI marked with three equal size terminals and PVC / Polycarbonate insulated body of 50 x 25mm size complete all as specified & directed.

Supply and fixing ding dong bell, AC, 230 volts, single pole complete all as specified & directed.

Supply and fixing in repair decorative wall mounting, fixture with opal PC diffuser suitable for 10/12 watt LED Lamp, lamp holder, including 12 Watts LED bulb of 6500 K of B22 base cap, and all accessories pre-wired including connecting up complete all as specified and directed.

Supply and Fixing in repair surface and wall mounted LED batten 10 watt 2 feet long extruded aluminium housing provided for efficient heat dessipation with polycarbonate diffusser and integrated electronic drive suitable for mirror fittings, all accessories pre-wired including connecting up with twin core flat flexible copper conductor cable of suitable size complete all as specified and directed.

Taking down of exsting u/s tube light fitting and supply and fixing in repair on surface and wall mounted LED batten with polycarbonate housing and initigarated electronic drive 20 Watt fixture 4 feet provided for efficient heat dissipation with policorbonate diffuser and integrated electronic driver and all accessories pre-wired including connecting up with twin core flat flexible copper conductor cable of suitable size with connector block complete all as specified and directed.

Taking down of exiting u/s security light fitting and supply and fixing energy saving security light fitting of 45 watts LED Versatile pressure die-cast aluminium IP 66 roadway luminaire with high power LED as light source comprising with electronic driver and all accessories pre-wired incl connecting up with PVC insulated copper conductor cable 1.5 Sqmm, 3 core as required for connections and 50 mm bore light grade G. I. tube mounting bracket of 1.5 meter in length, bend to shape at 140 degree in ‘L’ shape and fixed to wall by means of 02 nos. of 40 x 5 mm flat iron clamps, nuts, bolts and washers etc complete all as specified and directed.

Supply and fixing Ventilating fan wall mounted type of 200 mm sweep, 230 volts, AC, 50 Hz capacity, cutting of hole in wall, making of wooden frome, all arrangements for mounting of fan including making good of disturbed surface etc complete all as directed by Engineer - in - charge.

Supply & fix water heater storage type, electric, capacity 25 litres complete and depositing old/UNSV to MES store.

Material and labour for sub main wiring with 06 Sqmm nominal cross sectional area, two single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable with and including continuous earth wire of size 04 Sqmm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 25 mm dia, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and making good to the disturbed surfaces to match the existing including taking out the unserviceable sub main wiring complete all as specified & directed.

Supply and fixing in repair sheet metal enclosure distribution board, single pole and neutral, AC, 240 volts, 08 way, with 200 Amps rated copper bus bar and metal door with IP - 43 & IK 09 protection along with cable end box for above DB and flush to wall including all cutting etc in wall and making good to the disturbed surfaces to match the existing complete all as specified directed.

S&F (in replacement) industrial type SPN enclosure with a two pin and earth plug and socket complete with and including MCB SP, AC, 230 volts of 20 Amps, 'C' curve 10 KA breaking capacity and flush to wall including all cuttings & chases etc in wall and making good to the disturbed surfaces to match the existing complete

Supply and fixing in repair sheet metal enclosure distribution board triple pole and neutral (VTPN), AC, 440 volts, 04 ways with 200 Amps rated copper bus bar and metal door with IP 43 & IK 09 protection along with cable end box for above DB and flush to wall including all cutting etc in wall and making good to the disturbed surfaces to match the existing complete all as specified and directed and comprising of the following:- Make :-Legrand/Havells/Indoasian/Schneider (a) MCCB, 125 Amps, 04 pole, AC, 415 Volts of 16 KA breaking capacity complete - 01 No. Make :- Legrand/Havells/Indoasian/Schneider (b) MCB, SP, AC, 240 volts of 40 Amps, "C" curve, 10 KA breaking capacity - 12 Nos. Make :- Legrand/Havells/Indoasian/Schneider

Supply and fixing in repair MCB, SP, AC, 240 volts of 06 to 32 Amps capacity "C" curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified & directed.

Supply and fixing in repair MCB, SPN, AC, 240 volts of 40 Amps capacity "C" curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified & directed.

Material & labour for earthing complete with galvanised mild steel earth plate electrode 60cmx60cmx6mm thick buried vertically in ground (earth pit not less than 2.25meter deep below ground level) with top edge of the plate not less than 1.5meter below normal ground level steel earth plate connected with GI wire 04mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15mm bore light grade all as shown in elect plate No 3 on serial page No 497 of SSR part I - 2009 and connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150mm thick around GI earth plate, GI pipe medium grade 20mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover 40mm thick in PCC 1:2:4 type B1 duly reinforced with MS Bars 6mm dia at the rate of 75mm center to center both way with 12mm dia lifting handle and pit / chamber in PCC 1:3:6 type C1, Angle iron 40mmx40mmx3mm frame for pit cover including testing on completion complete all as specified and directed.

Taking down ceiling fan any make from ceiling carefully, cleaning to remove any type of sticky dust with cleaning material as required and re-fixing in its original / desired location with necessary connection incl provision of cable from ceiling rose to connector of fan after repairing, greasing, oiling, replacement of minor items such as pins, nut bolts, flexible wire etc incl spray painting with synthetic enamel paint in white colour complete

SHYAM ENTERPRISES

Adhunik Builders

M/S GDR CONSTRUCTIONS

garnet engineers contractors

The new hut furnitures

M/s SAAR ENGINEERS

Shivom Projects Private limited