WBPWD/AE/MSDSS/NIeT-06/2025-26

Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete (a) Depth of excavation not exceeding 1,500 mm. Connecting Corridor For Toilet

Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work) (a) With earth obtained from excavation of foundation

Supplying and laying Polythene Sheet (150gm / sq.m.) over damp proof course or below flooring or roof terracing or in foundation or in foundation trenches

(A) Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity

(I) Cement concrete with graded stone ballast (40 lTIm size excluding shuttering) In ground floor (a) 1:3:6 proportion

Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor) (g 2S mm to 30 mm shuttering without staging in foundation

(c) Steel shuttering or 9 to 12 mm thick approved quality ply board shuttering in any concrete work

Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes. (i) Pakur Variety

Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant IS codes a) Pakur Variety

Relnforcement for reinforced concrete work in all sorts of structures Including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and dlrectlon. (a) For works in foundation and upto roof Of grlgUnd floor/Upto 4 m

Brick work with 1st class bricks in cement mortar (1:6) (a) In foundation and plinth

(bj In superstructure, ground floor

125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor

Supplying& laying 20 mm designer chequered tiles of any shade and of approved quality as per IS: 1237: 1980 laid in patterns as directed in pavement, footpath including necessary underlay 25 mm thick average cement mortar (1:3) complete in all respect with all labour and materials [using cement slurry @ 4.4 kg/Sq.m at bacl‹ side of tiles. Cement of mortar & slurry will be supplied by the Department. Border concrete if necessary to be paid separateIyJ.

Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out jolnts Including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] (i) With 1:6 cement mortar (c) 15 mm thick plaster

(b) 20 mm thick plaster

(ii) With 1:4 cement mortar (c) 10 mm thick plaster

Neat cement punning about 1.5mm thick in wall, dado, window sill, floor etc. NOTE:Cement 0.152 cu.m per100 sq.m. Connecting corridor

Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. In Ground Floor: (a) One Coat

Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer's specification and as per direction of Engineer-in- Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. In Ground floor (Two Coat) b) Premium 100% Acrylic Emulsion

(a) M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor. (Add extra @ 1% for each addl. floor upto 4th floor and @ 1.25% for each addl. floor above 4th floor (li) Grill weighing above 16 Kg./sq.mtr and above In G.F

Supplying, fitting and fixing windows and ventilators with or without integrated grills conforming to IS 1038-1975 and manufactured from rolled .‘‘ steel sections conforming to IS 7452-1974 with non-friction projecting type, box type hinges, glazing clips, lugs locking bracket, handle plate etc, Including hoisting in position, straightening if required, fiXing lugs in cement concrete ( 1:2:4) with stone chips 20 mm down cutting holes and mending good damages to match with existing surface complete in all respect excluding glazing. (b) Openable steel windows as per IS sizes with Side hung shutters and horizotal glazing bars. [The extra rate admissible for the openable portion only]

(c ) Extra over item no. 17 for, (ii) Top hung side hung ventilators as per I.S. sizes 580 mm for Toilet ventilator

(viii) M.S. integrated grill as per approved design integrated with steel window or ventilator, joints continuously welded with M.S. flats and bars.

(vi) steel peg stay 300 mm long including fitting and fixing.

(a) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc

(A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : (b) On steel or other metal surface : With other than hi-gloss of approved quality (iv) Two coats (with any shade except white)

Supplying best Indian sheet glass panes set in putty and fitted and fixed with nails and putty complete. (In all floors for internal wall & uptlD 6 m height for external wall)

Supplying, fitting and fixing c.i. pipes of TATA Make with all necessa accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, shOFt piece etc. fitted with holder bats clamps, including cutting pipes, making threads, fitting, flxing etc. completein all respect including cost of all necessary fittings as required.J”oin ing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately) (A) For Exposed Work (ii) 25 mm dia. medium quality

(ii) 15 mm dia. medium quality

Supplying, fitting and fixing Peet's valve fullway gunmetal standard pattern best quality of approved brand bearing I.S.I. marking with fittings (tested to 21 kg per sq. cm.). (A) For Exposed Work (vii) 25 mm dia For Toilet

Supplying, fitting and fixing bib coCk or stop cock. (ii) Chromium plated Bib Cock long body with wall flange with aerator (Equivalent to Code No. 512 & Model - Tropical / Sumthing Special of ESSCO or similar brand)

(d) (i) Chromium plated angular Stop Cock with wall flange (Equivalent to Code No. 5053 & Model - Florentine of Jaquar or similar brand).

(i) chromium plated Concealed Stop Cock (Equivalent to Code No. 514(A) & Model - Tropical / Sumthing Special of ESSCO or similar brand).

Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 dFld threaded to match wlth GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment wil( be made for accesories, specials. Payment for painting will be made seperately) (A) For Exposed Work PVC Pipes 40 mm

Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. specification with P.V.C. fittings complete,C.I. brackets including two coats of painting to bracket etc

Supplying P.V.C. water storage tank of approved quality with closed top with lid (Black) - Multilayer (a) 500 litre capacity

Labour for hoisting plastic water storage tank. (i) Upto 1500 litre capacity. capacity (a) Upto 1st story from G.L

Labour for punching hole in plastic water storage tank upto 50 mm dia

Supplying, fitting and fixing white vitreous china best quality approved make wash basin with C.I. brackets on 7S mv x 75 ITIL Wooden blocks, C.P. waste fittings of 32 mm dia., one approved quality brass C.P. pil(ar cock of 15 mm dia., C.P. chain with rubber plug of 30 mm diä., approved quality P.V.C. waste pipe with C.P. nut 32 mm dia., 900 mm long approved quality P.V,C. connection pipe with heavy brass C.P. nut including mending good all damages and painting the brackets with twO COdtS Of approved paint. (iii) 630 mm X 450 mm size

Supplying, fitting and fixing pedestal of approved make for wash basin (white)

Supplying,fitting and fixing approved brand P.V.C. CONNECTOR white flexible, with both ends coupling with heavy brass C.P. nut, 1S mm dia. (v) 900 mm long

Supplying,fitting and fixing approved brand 32 mm dia.P.V.C. waste pipe, with PVC coupling at one end fitted with necessary clamps (iv) 1050 mm long

Supplying, fitting & fixing Aluminium domical grating. (iii) 100 mm For Toilet

Supply of UPVC pipes (B Type) & fittings conforming to 15-13592-1992 (A) (i) Single Socketed 3 Meter Length (b) 110 mm

(B) Fittings (ii) Plain Tee (b) 110 mm

(i) Door Tee (b) 110 mm

x) Bend 87.5° (b) 110 mm

xi) Door Bend (T.S.) (b) 110 mm

xv) Vent Cowl (b) 110 mm For Toilet

xvi) Pipe Clip (b) 110 mm

Labour for fitting and fixing U.P.V.C. pipes for above ground work including cost of jointing materials etc. fitting and fixing all necessary specials, cutting pipes, cutting holes in walls or R.C. floor where necessary and mending good all damages excluding the cost of masonry or concrete work, if necessary, but including the cost and fitting and fixing holder bat clamps (any floor) or for underground work including cutting trenches upto 1.5 metre and refilling the same complete as per direction of the Engineerin-charge. (Payment will be made on centre line measurement of the total pipeline including specials. {A) Above ground (b) 110 mm For Toilet

Supplying, fitting and fixing E.W.C. in white glazed vitreous chinaware of approved make complete in position with necessary bolts, nuts etc. (a) With ’P’ trap

Supplying, fitting and fixing Flat back urinal (half stall urinal) in white vitreous chinaware of approved make in position with brass screws on 75 mm X 75 mm X 75 mm wooden blocks complete. (i) 635 mm X 395 mm X 420 mm

Supplying, fitting and fixing Closet seat of apprOvI?ą make with lid and C.P. hinges,rubber buffer and brass screws complete. (a) E.W.C. (ii) Plastic (hallo v type) white For Toilet

Supplying, fitting and fixing bevelled edged mirror 5.5 mm thick silver. (ii) 600 mm X 450 mm

Supplying. fitting and fixing towel rail with two brackets (iii) 25 mm dia. and 750 mm long

Supplying, fitting and fixing PTMT Smart Shelf of approved make of size 300 mm.

Constructing Inspection pit of inside measurement 600mm X 600mm X upto 600mm (depth) with 250 mm thick 1st. class brick work in cement mortar (1:4) on alí sides, bottom of the pit consisting of 100 mm thick cement concrete (1:3:6) with stone chips over a layer of jhama brick flat soling, 15 mm thick (1:4) cement plaster to inside walls and out-side walls upto G.L. and 20 mm.thick (1:4) plaster to bottom of the pit, providing necessary inyert with cement concrete (1:3:6) with stone chips as per direction, neat cement finishing to entire internal surfaces, top of the pit covered with 100 mm thick R.C.C. slab (1:1.5:3) with stone chips and necessary reinforcerrients upto 1% and shuttering including 6 mm thick cement plaster (1:4) in ali external surfaces of the slab and one 560 mm dia. R.C.C. manhole cover of approved make supplied, fitted and fixed in the slab with necessary fittings,necessary earthwork in excavation in all sorts of soil, filling sides of the pit with earth and removing spoils after work complete in all respect with all costs of labour and materia

Construction of septic tank of different capacities as per approved drawing with 1st class brick work in cement mortar (1:4) İncluding two 560 mm dia. R.C.C. manhole cover(heavy typejof approved make supplied, fitted and fixed in the 100mm thick R.C.C (1:1.5:3) top slab with necessaryfind ce, 20mm thick cement plaster (4 : 1) with neat cementfinish to the internal surfaces and 15 mm thick cement plaster (< : 1) tO Outside wall upto 200 mm (ii) For 20 users

Construction of circular soak well 2.5 metre deep In all types of sandy soils with dry brick work upto 1.6 metre from the bottom havlng 150 mm intermediate cement brick work (1:4) band all round and cement brick work (1:4) upto 0.90 metre from top with 20mm thick cement plastering (1:4) to inside face upto the depth of cement brick work, 15mm thick cement plaster (1:4) on outer face from top of the well upto G.L. and 6 mm thick cement plaster (1:4) on top of the R.C.C. cover slab including filling bottom 1.00 metre of inside of the well with brick metal (50 mm to 63 mm size) including R.C.C. cover slab of 100 mm thick with cement conc (1:1.5:3) with stone chips with necessary reinforcement and shuttering including one 560 mm dia. R.C.C. manhole cover (heavy type)of approved make supplied, fitted and fixed in the cover slab with necessary fittings, making nacessary arrangements for pipe connections, excavation of well including shoring, dewatering and removing the exess earth from the premises as per direction complete in all respect with all costs of labour and materials. With 250 mm thick dry brick work and 250 mm thick cement brick work (1:6) and 1.00m inside dia (ii) For 20 users

Supplying, fitting and fixing fibre reinforced polymer (FRP) Composite door frame as per approved section with glass fibre reinforced plastic moulded skins and a special sandwich core, so as to impart monolitaheic composite structure as per approved technology of Department of Science and Technology (DST) tO SdÏïSfy IS: 4020 door testing performance criteria.. (i) 66mm x 90mm

Supplying, fitting & fixing fibre reinforced polymer (FRP) Composite door shutters as per approved design with glass fibre reinforced plastic mouldedskins and a special sandwich core, so as to impart monolitaheic composite structure as per approved technology of Department of Science and echnology (DST) to satisfy IS:4020 door testing performance criteria. In groUFld flOOF. (i) 32 mm thick

Iron butt hinges of approved quality fitted and fixed with steel screws, with isl mark. (vi) 100mm. X 50mm. X 1.25mm

Iron hasp bolt of approved quality fitted and fixed complete(oxidised) with 16mm dia rod with centre bolt and round fitting. (b) 250mm long

Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete: (a) With continuous plate base (Hexagonal/ Round rod) (v) 125 mm grip x 12 mm dia rod.

Anodised aluminium barrel / tower/ socket bolt (full covered) of approved manufactured from extruded section conforming to I.S. 204/74 fitted and fixed with cadmium plated screws: (iv) 150mm long x 10mm dia. bolt. (iv) 150mm long x 10mm dia. bolt.

Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each ti(e & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including toughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint fil(ing using white cement slurry @ 0.20kg/Sq.m. (a) Area of each tile upto 0.09 Sq.m (ii) Other than Coloured decorative including white (A) Flaor

(a) Area of each tlle upto 0 09 Sq m (ii) Other than Coloured decorative includj!!g White

Acrylic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturer's specification) including cleaning and smoothning of surface.

Please Enable Macros to View BoQ information