Repair of Main Building, Boundary Wall, Campus Development Work, Construction of Toilet, Interior and Furnishing Work of Senior Officer Quarter No.-2 at Dindayal Nagar, Ranchi

Amount

Earth work in excavation in foundation trenches in ordinary soil ( vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I.

Providing coarse clean sand in filling in in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume)

Providing designation 75B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I.

Providing and laying cement concrete in kerbs, steps and the like at or near ground level excluding the cost of centering, shuttering and finishing. 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

Providing designation 75B brick work in C.M (1:6 ) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size)

1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level.

1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Providing designation 75A brick work in C.M (1: 6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I.

Providing designation 75 B brick work in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including, providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing:

1:1½:3 (1 cement : 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for

Foundations, footings, bases of columns, etc. for mass concrete

Columns, Pillars, Piers, Abutments, Posts and Struts

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers

providing Tor steel reinforcement of 8mm dia rods as per approved design and drawing exclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. TMT Fe 500 (only valid for SAIL & TATA STEEL JSPl , Steel

providing Tor steel reinforcement of 10mm,12mm,& 16mm. dia bars as per approved design and drawing inclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I.

(a) 10mm (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)}

(b) 12mm (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)})

Providing 6mm cement plaster (1:4) in celling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Supplying, fitting, and fixing M.S. Grill made of 20X6mm M.S. Flate as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction of E/I. (where materials is not supplied by the deptt.)

Providing two coat of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface throughly , scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5 mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineer- in-Charge.

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC ‘C’ channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the ‘C’ Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer’s specification & drawing.

30 mm thick pre laminated PVC door shutters

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels.

Area of slab upto 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Marble work

Providing and fixing machine cut, mirror/ eggshell polished , Marble stone work for wall lining (veneer work) including dado, skirting, risers of steps etc., in required design and pattern wherever required, stones of different finished surface texture, on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with white cement slurry @ 3.3 kg/sqm including pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing, polishing etc. all complete as per Architectural drawings, and as directed by the Engineer-in-Charge.

18 mm thick Italian Marble stone sIab,PerIato, Rosso verona, Fire Red or Dark Emperadore etc

Water proofing for Old and New Roof Slab :- Providing and laying water proofing treatment on roof slab by applying two Component, factory designed, ready to use, acrylic modified flexible

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Hot finished welded type tubes

roviding and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /seIf tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and laying 60 mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Providing and laying vitrified Paring / Industrial tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 4457:2007, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 300x300 x 10 mm sizes.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.

For thickness of tiles 10 mm to 25 mm

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

Size of Tile 600 x 1200 mm

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

Size of Tile 600x600 mm

Providing and fixing false ceiling at all heights including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I):2011 (Board with BIS certification marks)

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Providing two coats of plastic emulsion paint of approved shade and make over old surface including washing cleaning and preparing the walls scaffolding washing of floor and taxes all complete as per building specification and direction of E/I.

Finishing walls with textured exterior paint of required shade :

New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm

Providing & Applying high quality acrylic modified resin based texture of Dholpur/Red sand stone Pattern with anti algae and UV resistance properties to be applied as intermediate finish in desired pattern @ 43.04 kg/10 sqm to form film of 1- 1.5 mm thickness after scrapping and properly cleaning the surface to remove loose particles from the plaster surface, followed by top coating with Premium Acrylic Smooth exterior paint with Silicone additives of required shade by two or more coats @ 1.43 litre/10 sqm, complete as the direction of Engineer -in-Charge.

Providing two coats of oil bound distemper of approved shade and make over old surface including washing cleaning and papering the walls, scaffolding, washing of floors and taxes all complete as per building specification and direction of E/I.

Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body.

Using R2 series with frame (70 mm & above) x (40 mm & above) & both glazed and fly screen sash (25 mm & above) x (50 mm & above) with zinc alloy (zamak) powder coated touch locks with hook. (Height upto 1.2 metre).

Casement door double panel with French (False) Mullion with zinc alloy (zamak) 3D hinges, multi-point locking system with cylinder, zinc alloy (zamak) powder coated handles on both sides.

Using R3 series with frame (55 mm & above) x (50 mm & above) & sash (55 mm & above) x (85 mm & above) & French (False) mullion (55 mm & above) x (60 mm & above). (Height upto 2.5 metre).

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with :

5.5 mm thick glass panes

Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete.

Providing two coat of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface throughly , scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 250 mm

Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed in DSR 2023 as per building specification and instruction of E/I all complete

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointing with white cement including rubbing, polishing and cost of curring taxes and royalty all complete as per building specification and direction and E/I.

With "A" grade white 15X15cm Tiles.

Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking at site dump manure from approved source, including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment) :

Screened through sieve of I.S. designation 20 mm

Rough dressing the trenched ground including breaking clods

Fine dressing of the ground

Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of officer-in-charge

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately

Holes 60 cm dia, and 60 cm deep

Providing and stacking of Bottle palm of ht. 210-240 cm bottom girth 30-35 cm well developed in big HDPE bags

Providing and stacking of Bottle palm of ht. 270-300 cm bottom girth 40-50 cm well developed in big HDPE bags as per direction of the officer-in-charge.Each

Point Wiring in PVC Conduit, with Modular type Switch: Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with modular type switch, modular plate, suitable size of GI box etc as required.

Group-C

Power Plug wiring in PVC Conduit (2X4 Sq.mm) :- Wiring for light/power plug with 2x4 Sq.mm FR PVC insulated copper conductor songle core cable in surface/recessed PVC conduit along with 1 No. 4 Sq.mm FR PVC insulated copper conductor single core cable for loop earthing etc. as required.

Circuit/Sub-main wiring in PVC Conduit:- Wiring for circuit / sub-main wiring along with earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required.

2x1.5 Sqmm + 1x1.5 sqmm earth wire(for Single Separate 5A from nearest switch board )

2x2.5 Sqmm + 1x2.5 sqmm earth wire (for switch board circuit to LDB and UPS 6 A Sockets Circuit).

2x4.0 Sq.mm + 1x4.0 Sq.mm earth wire. (AC & GYZER)

2x6 Sqmm + 1x6 sqmm earth wire

4x6 Sqmm +2x6 sqmm earth wire.(to be used for all LDB)

4x10 Sqmm +2x10 sqmm earth wire.(to be used for all PDB)

1 x 1.5 sq.mm

3 x 1.5 sq.mm

S/F PVC Conduit: Supplying and fixing of following sizes of Rigid 2 mm thick PVC conduit alongwith the accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required for TV and TEL out lets.

S/F Modular type Switch / Socket:- Supplying and fixing following modular type switch / socket on the existing modular plate and switch box including connections but excluding modular plate etc as required. (to be used in switch board with sockets)

5/6 amps, one way modular switch

15/16 amps, one way modular Switch

5/6 amps, 3 pin modular socket

6/16 amps, 6 pin modular socket

S/F Modular type electronic fan regulator:- Supplying and fixing stepped (two module) type fan regulator on the existing modular plate switch box including connections but excluding modular plate etc as required.

S/F light plug point with modular type accessories:- Supply and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 5 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch, connection, painting etc as required.

S/F power plug point with modular type accessories:- Supply and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular type switch, connection, painting etc as required.

S/F Ceiling Rose:- Supplying and fixing 2 pin ceiling rose on the existing junction box/ wooden block including connection etc as required.

S/F Batten / Angle Holder:- Supplying and fixing batten / angle holder including connection etc as required.

S/F Electonic Musical Call Bell:- Supplying and fixing electronic musical call bell suitable for D.C./A.C. single phase, 230Volts, complete etc as required.

ITC fluorescent fitting directly on surace:- Installation, testing and commissioning of Pre-wired fluorescent fitting /compact fluorescent fitting of all types, complete with all accessories and tube etc.directly on surace or ceiling/ wall, including connection with 1.5 Sq. mm. FR PVC insulated, copper conductor, single core cable and earthing etc. as required.

ITC fluorescent fitting with down rods:- Installation, testing and commissioning of Pre-wired fluorescent fitting /compact fluorescent fitting /2x20W LED Tube light of all types, complete with all accessories and tube etc.directly on surace or ceiling/ wall, including connection with 1.5 Sq. mm. FR PVC insulated, copper conductor, single core cable and earthing including supplying and fixing ball & socket arrangement, 2 No. down roads of 20 mm dia x 1.6 mm thick steel conduit (up to 30 cm lenght), painting & wiring the down rods with 1.5 sq.mm. PVC Cu. conductor sinlge core cable and earthing etc. as required.

S/F Extra Down Rod:- Providing and fixing extra conduit down rod of 20 mm dia, 2x10 cm, length with 2x1.5 Sq.mm FR PVC insulated copper conductor, single core cable including painting etc. as required. (Note more than 5 Cm. length shall be rounded to the nearest 1) (Extra Down Rod For Ceiling Fan)

ITC Exhaust Fan upto 450 mm sweep:- installation of exhaust fan upto 450 mm sweep in the existing opening, including making the hole to cut the size of the above fan, making good the damage, including connection, testing, commissioning etc as required.

S/F SP MCB DB:- Supplying and fixing following way, SP&N MCB distribution board of sheet steel for 240 Volts on surface /recess complete with tinned copper bus bar, neutral busbar, earth bar, detachable gland plate, interconnections, phophatized and powder coated painted including earthing etc. as required ( But without MCB/RCCB/ ISOLATOR). Make- L&T/Legrand/ Schneider.

16Way Double Door.

S/F TP MCB DB: Supplying and fixing following way,three pole and neutral sheet MCB distribution board, 415 volts on surface/recess complete with tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections,phosphatised and powder painted including earthing etc. as required ( But without MCB/RCCB/ ISOLATOR). Make- L&T/Legrand/ Schneider.

6 ways (4+18) Double Door. (horizontal type)

S/F 'C' series MCB:- Supplying and fixing 240/415 V, 10 kA, 'C' series, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc, as required.

6/32A Single Pole

6-32 A DP MCB

50/63A TPN (To use as incommer for all TPN D.B.)

80mm dia Earthing Electrode 2mtr. Length / 80mm dia Earthing Electrode 3mtr. Length / 50mm dia Earthing Electrode 2mtr. Length/50mm dia Earthing Electrode 3mtr. Length & Backfill Compound chemical 4 Bag(per bag 25 KG)

S/L 8 SWG copper wire in ground:- Supplying and laying of 8 SWG copper wire at 0.50 meter below ground level for conductor earth electrod, including soldering etc. as required.

P/F 25 x 5mm G.I. earth strip in surface/recess :- Providing and fixing 25mmx5mm G.I. earth strip in surface /recess for connections etc. as required and making the earth grid for all G.I. Earthing pits of the building.

Supply of 1400 mm (56") BLDC 5 STAR 32W CEILLING FAN

Supply fiting fixing and testing fof 400 mm (16") sweep AC 230/250 volts, 50 HZ Wall Mounting Revolving Fan with brackets, cooper winding 5 star rated etc. complete all electric room etc. (Make : Usha/ Bajaj / Crompton / Havells)

Supply of 230 mm (9") Exhaust fan (Metal body) suitable for single phase 230 volts, 50 Hz., AC supply complete with motor, louvers/shutters etc. complete as required. Make- Havells / Usha / Crompton/ (METAL BODY)

Supply, fitting, fixing & testing of 15W LED recessed Downlighter with cutout dia 145 mm suitable of Armstrong /CRG/TRAC/USG/Celotex/ POP Muduler Celling . Must be white Power doatedpreseure die cast aluminum housing for superior heat management and beautifully designed with white modled in engineering plastic Make :- .Trilux/ Lighting Technology/Philips.

Supply, fitting, fixing and testing of building outer lighting luminaire aerodynamically shaped single piece pressure die-cast Aluminum luminaire with high power LEDs as light source and electronic driver (IP65), along with 45/48W LED Lamp, as Energy saving as per drawing prescribed reflector and heat resistant toughened flat glass cover, with 5ft long 40mm dia G.I. pipe with 3 Nos. of iron clamps , anchor nut bolts with double washers as per direction of E/I or consultant as per drawing prescribed reflector and heat resistant toughened flat glass cover (IP-65) and in compliance to IEC Safety Standards. LM 79 and LM 80 reports to be submitted with all accessories. Make :- .Trilux/ Lighting Technology/ Philips.

LED BATTEN (20/22W)

1.5Tr. 5 Star split A.C (Inverter Type) IS-1391-part-I

2.0Tr. 5 Star Split A.C (Inverter Type) IS-1391-part-I

copper tube of size 1/4" for split ac unit 1/1.5/2/3 tr capacity including nitride rubber insulation

copper tube of size 1/2" for split ac unit 1/1.5/2/3 tr capacity including nitride rubber insulation

drain pipe for AC

4 core 4sqmm Copper cable

Outdoor stand for 2.0tr split AC

CAT 6 wire

approved make LED Bollard fitting with cylindrical shape, height 600 to 850mm, 8/9Watt with Die cast aluminium housing opel with PC diffuser, IP:65/54 IS:10322 part 5

40/45W LED Clear approved make LED Post top made in die cast aluminium housing with decorative clear/opal acrylic diffuser and IP65 protection IS:10322 part 5/ section 3

Fabrication,installation with 16swg MS sheet with one coat steel primer and two coat spray painting with approved shade making PCC plinth and foundation including fitting fixturing connection transpotation upto work site, labour charge etc all complete as reqd.(Main Cubical Panel) a) 100Amp 4pole 35 KA MCCB 2nos b)150/160 Amp 4pole 35 KA MCCB 2nos c)100 Amp Changeover 2nos d) 40 Amp DP MCB "C" Series 10KA breaking Capacity 4nos e)Voltmeter 1nos f) Amp meter 1nos g)C.T.Coil 3 nos h) Iidicator lamp 3nos i) 45mmx 10mm copper strip (busbar)15 kg

S/F Modular Computer board cosisting switch & socket in 8 modular board etc as per required

1.24.1 5/6 amps, one way switch 1 X67=67 1.24.3 15/ 16 amps, one way switch 1 X102=102 1.24.4 5/6 amps, 3 pin socket outlet 1 X 88=88 1.24.5 15/16 amps, 6 pin socket outlet 2 X 145=290 1.27.4 8/9 module box 1X288=288

S/F Modular Computer board cosisting switch & socket in 6 modular board etc as per required

1.24.3 15/ 16 amps, one way switch 2 X102=204 1.24.5 15/16 amps, 6 pin socket outlet 2 X 145=290 1.27.3 6 module box 1X240=240

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge

20 mm nominal outer dia Pipes

Providing and fixing on wall face unplasticised Rigid PVC rain waterpipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

75mm dia

110mm dia

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Single tee with door

75mm dia

110mm dia

Single tee without door

75mm dia

110mm dia

75mm dia

110mm dia

Carriage of matarials

Sand - 8km

Bricks - 8km (1k + 7p)

Chips - 22 km

Local Sand - 3 km

Supplying Fitting and Fixing 6 mm VEGAS EXTERIOR HPL SHEET,

Providing Fitting & Fixing opal jali do - do

Supplying fitting and fixing UniversalCloser (suitable for both anti-clockwise and clockwise doorswithout any change in the parts ofcloser)

Supplying fitting and fixing Sun screen Roller Blind

Supplying fitting fixing all height wall paneling with 12mm ply wood over 50mm x 25mm aluminum section veener fininsh with all taxes and royalty all complete as per E/I

Providing, fitting anf fixing upper cabinet/lower cabinet/rack/book shelf/wall unit including the cost of all material and lanour excluding taxes & royalties all complete as per building specification and instruction of E/I

Providing and fixing 30mm Flush door of ply wood Century or ISI mark water proof ply grade and pasting with 4mm Veneer of green Decor make at both side with all material and labour all complete (including all fancy type fitting) as per building specification and direction of E/I.

Supplying Fitting and fixing Triple burner gas stove

Supplying Fitting and fixing wall mount baffle filter decorative kitchen chimney

Supplying FittingI-Comp Intel Core i5 12500 8 GB/ 0GB HDD/ Windows 11 Professional

Supplying fitting and fixingPEWI Modular Metal Drawer FileCabinet Pedestal 680 millimeter400 millimeter 450 millimeter

Supplying fitting and fixing Canon Multifunction Machines Mfm, On Site OEM Warranty 1 Year

Supplying fitting and fixingTitan Plastic Dial And Hands WallClocks

Supplying fitting and fixing Computer Table consists of Computer table with key board drawer and table top

Supplying Fitting and Fixing Revolving Chair with Knee

Supplying fitting and fixing Angular 1 Seater Sofa With Leatherite Cover

Supplying fitting and fixing HARLISON Sofa Sets, Number of seats 5

Supplying fitting and fixing Bharat Bhushan & co. RectangularCENTRE TABLE with Temperedglass Top of 914mmX914mm

Supplying fitting and fixing Executive Table with One side pedestal unit and E.R.U

HARLISON Non-Revolving and Non-Tilting chair with Armrest

Supplying fitting and fixing kings Furnishing Executive Tablewith One side pedestal unit andE.R.U

Supplying fitting and fixing HP S Non-Revolving and Non-Tilting chair with Armrest

Supplying fitting and fixing Revolving Chair withKnee tilt Synchronic mechanism RK EMPIRE

Supplying fitting and fixing DNR SYSTEMS Revolving ChairWith Arm Tilt working withtorsion bar mechanism

Supplying fitting and fixing GREENSCAPE 1 Seater Sofa WithFabric Cover

Supplying fitting and fixing GODREJ INTERIO 1 Seater Sofa With Fabric Cover

Supplying fitting and fixing GRAPHIC Single storage SideTable, H 650 mm mm X D 500 mm GRAPHIC (Side Table)

Supplying fitting and fixing Angular 2 Seater Sofa With FabricCover

Supplying fitting and fixing 3 Seater Sofa With Fabric Cover

Wooden Single BedWITHOUT STORAGE BOX 1830 915125

Supplying fitting and fixing g g corporation--G GCORPORATION Mattress kapok-JSS Specifi cation small

Supplying fitting and fixing COTT-LIN Handloom Cotton BedSheets as per IS 745 Variety No - 12(140 g) of Size 229 x 140 cm

Supplying fitting and fixing JAI HIND Blanket Navy andBlanket Hospital as per IndianNavy Specifi cation NoDCV/PROV/BLANKET/2007available

Supplying fitting and fixing Bombay Dyeing TOWEL WHITE

Supplying fitting and fixing Onlymat 100cm X 60cmDecorative Coir Mats

Supplying fitting and fixing geeken Stainless Steel Dust Bin 2Bin Mounted with 3 Pole capacity50 ltr

Supplying fitting and fixing Vijay Round Glass Flower Pots OrPlant

Supplying fitting and fixing NEELKAMAL Without Lid 1400 mlWater Jug

Supplying fitting and fixing GODREJ INTERIO Pillow - Synthetic

Supplying fitting and fixing PUREREST Cotton Pillow 33 cm x 56 cm

Supplying fitting and fixing V J Interior Plastic Moulded Chair With Arms Without Cushion Single Piece Plastic Moulded

Matrix PABX System-EPABXCOMPLETE AS PER DETAILEDSPECIFICATION with extensionsNA analog trunk ( FXO) NA

Panasonic ABS Telephoneinstrument single push button

HOLA ! ABS Telephone instrumentsingle push button

Supplying fitting & Fixing AVB Round Plastic Flower Pots Or Plant do - do

EWC with soft closing seat cover

ADHUNIK SWITCHGEARS Push ButtonType Flushing Cistern Dual FlushSystem 10 LTR

HINDWARE Box Rim Type EuropeanPattern Toilet Seat

2 way bib coak for health faucet

Health faucet with 1 Meter Long Easy Flex tube in Chrome Finish & wall flap

HINDWARE Vitreous China Sinks /Wash Basins Flat Back andRectangle

Jaquar viterous china sinks /wash basin

Parryware Vitreous China Sinks /Wash Basins Other Pattern andRectangle

Wast coupling 32mm size full therade

Tall boy

PRIMA 15 mm Brass Fancy Tap PRIMA

Angle cock

Connection Pipe With Nuts ADHUNIK SWITCHGEARS

Towel rail

PRIDE Towel Rail Stainless Steel PRIDE

Towel Ring

Soap Dish

PRIDE liquid soap dispenser, Capacity100 Milliliter

Corner Glass Shelf

PRIDE 15 mm Brass Fancy Tap PRIDE (CP Wall Mounted Sink Mixer)

Jaquar Bathroom Hand Shower CastBrass Grade LCB-2 of IS:292/1983

Jaquar Bathroom Body Showers CastBrass Grade LCB-2 of IS:292/1983

PRIMA 15 mm Brass Fancy Tap PRIMA

BAJAJ 25 liter 4 Star Water Heater

Add 18 % GST (in Basic Rate must fill 12)

Add 1% Labour Cess (in Basic Rate must fill 1)

Ms Gokul Construction