IMPROVEMENT OF BATHROOM, TOILET AND KITCHEN AT BALIDAN STAMBH, SAINIK ARAM GRAH AND SUNJUWAN UNDER GE JAMMU

Amount

Demolition of brick work or stone / boulder masonry built in cement mortar including all quoins, arches, pillars etc., but excluding ashlar facing, dressed stone work and precast concrete articles complete all as specified and as directed.

Demolition of cement concrete (unreinforced) or tiling etc in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed.

Demolition of cement concrete (reinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed.

Taking down cement plaster / wall tiles including backing etc from brick / stone walls / concrete surfaces including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

Taking down chowkhats or frames including shutters (without taking off shutters from the frame) not exceedinh 1.5 Sqm each complete all as specified and as directed.

Taking down chowkhats or frames including shutters (without taking off shutters from the frame) exceeding 1.5 Sqm but not exceeding 4.0 sqm each complete all as specified and as directed.

Taking down shutters of any description exceeding 1 Sqm and not exceeding 2 Sqm each complete all as specified and as directed.

Taking down easing and adjusting shutters of any description exceeding 1.00 Sqm and not exceeding 2.00 Sqm each and re-fixing in the same opening complete all as specified and as directed.

Material and labour for brick work with sub class ‘B’ bricks (old size), straight or curved on plan exceeding 6m in mean radius, built in cement mortar (1:6) complete all as specified and as directed.

Material and labour for brick work with sub class ‘B’ bricks (old size), straight or curved on plan exceeding 6m in mean radius, built in cement mortar (1:6) but except brick i.e. using serviceable bricks obtained from Ser item No. 9.00 here-in-before complete all as specified and as directed.

Material and labour for pressed steel frames of size 125mm x 60mm made of 1.25mm thick mild steel sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate complete all as specified and as directed. Note: - PCC for filling of hollow portion shall be measured and paid for separately.

Material and labour for pressed steel frames of size 105mm x 60mm made of 1.25mm thick mild steel sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate complete all as specified and as directed. Note: - PCC for filling of hollow portion shall be measured and paid for separately.

Material and labour for PCC (1:3:6) nominal mix type C-0 (using 12.5mm graded crushed stone aggregate) as in filling of pressed steel door frames / chowkhats complete all as specified and as directed.

Material and labour for PCC (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) as in anchoring hold fast, parapets, coping, apex plates, bed plates and the like including weathering, slightly rounded or chamfered angles and throating etc. complete all as specified and as directed.

Material and labour for 35mm thick second class hard wood (Sal / Hollock), glazed and skeleton shutters (factory made), open, rebated and prepared to receive glass or gauge etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., size of members of shutters as specified in clause 8.24 (a) of SSR Part-I complete all as specified and as directed.

Material and labour for 35mm thick factory made second class hard wood (Sal / Hollock) plain, framed, panelled shutters (two panels) with lock rail and panels of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial face veneers on both sides. The size of rail and style as per IS–1003 (Part-I), kiln seasoned and chemically pressure treated, fitted to chowkhats complete all as specified and as directed.

Supply and fixing solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tube, supplied and fitted in openings as per specification and drawing shown in SSR Part-II complete all as specified and as directed.

Material and labour for factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made of mild steel tube for top and bottom rails. Mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of plain colour PVC sheet 5mm thick to be fitted in mild steel frame welded / sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplied and fitted in the frame at site as per specification and drawings shown in SSR Part-II complete all as specified and as directed.

Supply and fixing in repair aluminium anodized powder coated (minimum thickness 50 micron) sliding window (Two track) consisting of two shutter of glazed including all necessary fittings and flyproof mesh shall be fixed on external face of window frame with aluminium beads, the following items shall be included in quoted rate of this item: - (a) Aluminium powder coated frame of section 63.5 x 38.10 mm x 1.02 mm thick with or without rebate. (b) Aluminium powder coated window shutters of section 40 x 18 mm x 1.25 mm thick (Both shutter of glass) including self locking catch and roller etc. (c) 4.0 mm thick coloured or tinted glass glazing as in aluminium window / ventilator with aluminium hollow beading / glazing clip (included with shutters) size 19mm x 17mm made out of 0.70mm thick hollow section weighing not less than 0.97 Kgs / RM including rubber gasket. (d) Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples and aluminium beads.

Description all as per Ser item No 19.00 here-in-before but as in bath / water closet vents (sliding upside) complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing butt hinges 100 mm long, stainless steel, medium weight and fixed complete all as specified and as directed.

Supply and fixing in repair aluminium alloy, anodised, sliding door bolt 300 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed.

Supply and fixing aluminium anodised, barrel tower bolts 200 mm of extruded section and fixed complete all as specified and as directed.

Supply and fixing aluminium anodised, barrel tower bolts 150 mm of extruded section and fixed complete all as specified and as directed.

Supply and fixing aluminium anodised handles 150 mm of extruded section and fixed complete all as specified and as directed.

Supply and fixing aluminium anodised handles 125 mm of extruded section and fixed complete all as specified and as directed.

Supply and fixing in repair for floor door stopper of 140mm long cover plate of aluminium alloy body and tongue anodised with hard drawn steel spring, fixed in floor complete all as specified and as directed.

Supply and fixing mild steel 300mm, ordinary rat tail rod patttern springs including roller and roller plate complete fixed with screws or necessary welding to pressed steel door frame complete all as specified and as directed.

Supply and fixing stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and as directed.

Taking up or down steel tubing of 15mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings complete all as specified and as directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing, etc. and making good, cutting not exceeding 20 cm girth in brick walls complete all as specified and as directed.

Supply and fixing CPVC (Chlorinated polyvinyl chloride) pipes, bore (inner dia) of pipe in 15 mm of pressure rating 10 kgf / cm² fixed complete to walls, ceilings or in floors etc., any type of pipe complete all as specified and as directed. Note: - The rates for pipe including all pipe fittings such as ends, elbows, unions, tees, reducing tees, adapters, sockets, plugs, house clips as well as brass threaded fittings for all opening / connections such as bib taps / Stop valve etc.

Supply and fixing steel water tubing 15 mm bore medium grade galvanised with all fittings (ISI marked) fixed complete to walls, ceiling or laid in floors complete all as specified and as directed.

Taking up or down steel tubing of 20mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings complete all as specified and as directed.

Supply and fixing CPVC (Chlorinated polyvinyl chloride) pipes, bore (inner dia) of pipe in 20 mm of pressure rating 10 kgf / cm² fixed complete to walls, ceilings or in floors etc., any type of pipe complete all as specified and as directed. Note: - The rates for pipe including all pipe fittings such as ends, elbows, unions, tees, reducing tees, adapters, sockets, plugs, house clips as well as brass threaded fittings for all opening / connections such as Bib taps / Stop valve etc.

Refixing of old steel tubing 20 mm bore and connections in new or old position (walls, ceiling, floor etc.) complete all as specified and as directed.

Supply and fixing rotational moulded polyethylene water storage tanks three layers of 500 litres capacity ISI marked (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part - I including 20mm thick Ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (minimum weight 20mm-210 grams) including dismantling of old broken water tanks and refixing of inlet, outlet and overflow pipe etc complete all as specified and as directed.

Supply and fixing rotational moulded polyethylene water storage tanks three layers of 1000 litres capacity ISI marked (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part - I including 20mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (minimum weight 20mm-210 grams) including dismantling of old broken water tanks and refixing of inlet, outlet and overflow pipe etc complete all as specified and as directed.

Supply and fixing in repair 20 mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (minimum weight 15mm-142 grams / 20mm-210 grams / 25mm-455 grams / 40mm - 690 grams) complete all as specified and as directed.

Supply and fixing in repair CPVC (Chlorinated polyvinyl chloride) pipes, bore (inner dia) of pipe in 25 mm of pressure rating 10 kgf/cm² fixed complete to walls, ceilings or in floors etc., any type of pipe complete all as specified and as directed. Note: - As overflow pipe extended upto rain water pipe or 45 cm beyond external face of wall.

Supply and fixing in repair overhead shower, 65 mm ABS shower (without arms) complete all as specified and as directed. Makes: - PRAYAG, cat No BS-29 or equivalent in Jaquar, Prima, Kohler.

Supply and fixing in repair soap dish, vitreous china white, approximate size 160 x 160 x 90mm complete all as specified and as directed.

Supply and fixing in repair corner glass shelf with bracket fixed with chromium plated brass screws and wooden / plastic cleats complete all as specified and as directed. Make: - ACN-1173 of JAQUAR or equivalent in Prayag, Cera.

Supply and fixing in repair vitreous china squatting pan of pattern, long pan, 'Orissa pattern', size 580 x 440 mm white with integral foot rests (excluding flushing cistern and flush pipe) but including provision of lime concrete complete all as specified and as directed.

Supply and fixing in repair vitreous china wash down water closet pan (Pedestal pattern) white (excluding fixing bolts, flushing cistern and flush pipe) but including plastic water closet seat, white, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed.

Supply and fixing in repair for plastic water closet seat, white, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed.

Supply and fixing in repair hand shower (health faucet) mild steel chromium plated for 15 mm dia pipe with 1.25 m long flexible tube chrome finish and wall hook for water closet complete all as specified and as directed.

Supply and fixing in repair toilet paper holder with flat recessed type stainless steel complete all as specified and as directed.

Supply and fixing in repair PVC valveless, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle (including bracket, supply and fixing flush pipe PVC 32 mm dia) capacity of 10 litres complete all as specified and as directed.

Supply and fixing in repair vitreous china urinal, half stall type, white (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and as directed.

Supply and fixing in repair urinal spreader of PTMT any colour for fixing with 15 mm dia pipe (minimum weight 60 grams) complete all as specified and as directed.

Supply and fixing in repair sink with drainage board made of stainless steel 1 mm thick with plugs, washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brackets of angle iron and connecting union to pipe over all size 915 mm x 460 mm and bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

Supply and fixing in repair stainless steel plate rack (utensil rack) of size (900mm x 750mm x 250mm) made out of AISl 304 stainless steel 0.63 mm thick sheet fixed with brass screws of required size including necessary fittings / nuts, bolts and washers complete all as specified and as directed.

Supply and fixing in repair vitreous china wash basin, white flat back, size 550 x 400 mm excluding taps, waste chain and plug and porcelain stopper but including vitreous china pedestal and PVC waste pipe with union, flexible suitable for wash hand basin or urinal, 32 mm dia complete all as specified and as directed.

Supply and fixing 32 mm dia low density polyethylene pipes (LDPE) of pressure rating 6 kgf / cm² suitable for waste pipe etc fixed complete to walls, ceilings or in floors etc complete all as specified and as directed.

Supply and fixing in repair towel ring of PTMT or brass chromium plated fixed with and including chromium plated brass screws and wooden / plastic cleats (minimum weight 90 grams) complete all as specified and as directed.

Supply and fixing in repair brass chromium plated towel rail 20mm dia 'D' type 60 cm long between flanges complete all as specified and as directed.

Supply and fixing in repair sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed.

Supply and fixing in repair stainless steel, hat and coat hooks, solid body, 175mm to 250 mm complete all as specified and as directed.

Supply and fixing PVC connection 15 mm bore with PTMT nuts of length 450 mm long complete all as specified and as directed.

Material and labour in repair PVC (SWR) floor trap, dia of outlet in 75 mm, plain including grating but including jointing with solvent cement fixed complete all as specified and as directed.

Supply and fixing PVC grating square, 150 mm (hinge pattern and with or without hole) complete all as specified and as directed.

Supply and fixing in repair stop valve (ISI marked), cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 20 mm bore and fixed complete all as specified and as directed.

Supply and fixing in repair bib tap 15 mm bore long body, brass chromium plated, fancy type (long shank), with crutch or butterfly handle screwed down, screwed for iron / PVC pipe or for brass ferrule and fixed complete all as specified and as directed.

Supply and fixing in repair stop valve / angle valve (ISI marked), fancy type, chromium plated with long shank and cup (concealed type) screwed down high pressure with crutch or butterfly handle, screwed both ends for iron / PVC pipe or for unions of 15 mm bore and fixed complete all as specified and as directed.

Supply and fixing in repairs 15mm bore brass wall mixer 3-in-1 system with provision for both hand shower and overhead shower complete with 115mm long bend pipe, connecting legs and wall flange mixing hot and cold water, screwed down for 15mm dia iron pipe complete all as specified and as directed. Note: - Hand shower and overhead shower will be measured and paid separately. Makes: - CON-SOL 6281 of JAQUAR or equivalent in KOHLER, ARTIZE.

Supply and fixing in repair brass chromium plated mixer 15 mm bore for mixing hot and cold water suitable for wash hand basin etc, screwed down for iron pipe and fixed complete all as specified and as directed.

Supply and fixing in repair sink mixer with regular spout brass chromium plated for iron / PVC pipes 15 mm bore, screwed for iron pipe and fixed complete all as specified and as directed.

Supply and fixing in repair pillar taps, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without letter Hot or Cold with long screwed shanks and fly nuts screwed for 15 mm dia bore of pipe complete all as specified and as directed.

Material and labour for sunken slab treatment: - (a) 15mm thick plaster in cement sand mortar (1:3) mixed with water proofing compound, all as per manufacturer’s instructions shall be applied both on floor and wall. The surfaces then shall be cured and allowed to dry. All the joints of pipe shall be sealed properly. (Note: - Provision of PVC spout pipe as extended 45 cm beyond external face of wall to be measured and paid separately). (b) Apply a coat of moisture cured high tensile elastomeric modified polyurethane based liquid membrane on floor as well as on wall as per manufacturer’s instructions, after the treatment over, sunken portion shall be kept full of water for at least one week to check that no seepage is seen from the external wall / concrete surfaces.

Material and labour for cement concrete (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) as in mass filling, in sunken slab of toilets complete all as specified and as directed.

Supply and fixing in repair 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.

Supply and fixing in repair 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floor complete all as specified and as directed.

Supply and fixing 110 mm bore PVC (SWR) bends any radius, with or without excess door complete all as specified and as directed.

Supply and fixing 110 mm bore PVC (SWR) junction single, (single 'T') equal or unequal, with excess door complete all as specified and as directed.

Supply and fixing 110 mm bore PVC (SWR) vent cowl complete all as specified and as directed.

Supply and fixing in repair 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.

Supply and fixing in repair 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floor complete all as specified and as directed.

Supply and fixing 75 mm bore PVC (SWR) bends any radius, with or without excess door complete all as specified and as directed.

Supply and fixing 75 mm bore PVC (SWR) branch piece, single (Single 'Y') equal or unequal, with excess door complete all as specified and as directed.

Material and labour for non skid ceramic jointless coloured tiles, 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match over and including 15mm thick screed layer in cement mortar (1:4) complete all as specified and as directed.

Material and labour for non skid ceramic jointless coloured tiles, 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match over and including 15mm thick screed layer in cement mortar (1:4) complete all as specified and as directed.

Material and labour for glazed ceramic coloured tiles of size 450mm x 300mm, thickness 7mm as in vertical surfaces such as skirting, dado, wall etc., set and jointed in neat cement slurry and pointed with coloured cement to match over and including 10mm thick rendering in cement mortar (1:4) complete all as specified and as directed.

Material and labour for 20 mm thick granite black (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like including pointing into white cement (1:2) using marble dust with admixture of pigment to match shade of granite laid over and including screed bed or bedding layer of mortar 15mm thick for laying floor in cement mortar (1:4) finished even and rough to receive top layer complete all as specified and as directed.

Material and labour for 25 mm thick (average thickness) PCC (1:2:4), type B-0 (using 12.5mm graded crushed stone aggregates) as in floor by maintaining required gradient / undulation, finished even and fair complete all as specified and as directed.

Material and labour for rendering 5 mm thick plaster in cement mortar (1:3) on concrete surfaces as in ceilings finished even and smooth without using extra cement including additional thickness provided as floating / setting coat to cover exposed reinforcement of concrete slab complete all as specified and as directed.

Material and labour for preparing newly plastered surfaces and applying three coats of white wash as in ceiling etc complete all as specified and as directed.

Material and labour for preparing of plastered surfaces of ceiling, old decorated surfaces and applying two coats of white wash complete all as specified and as directed.

Material and labour for rendering 10 mm thick on fair faces of brick work or concrete surface in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for preparation of newly plastered surface of wall and applying two coats of oil bound distemper white or tinted shade complete all as specified and as directed.

Material and labour for rendering 15 mm thick in two layers (10 mm in base layer in (1:6) and 5 mm thick in (1:4) in second layer) on fair faces of brick work or concrete surface in cement mortar (1:4) finished even and smooth without using extra cement including water proofing compound complete all as specified and as directed. Note: - Water proofing compound will be measured and paid separately.

Supply only liquid water proofing compound @ 0.200 Litre per 50 kg of cement or as per manufacturer's instructions complete all as specified and as directed.

Material and labour for preparing newly plastered or concrete surfaces of wall and applying two coats of all weather coat or apex paint complete all as specified and as directed.

Material and labour for preparation of new or previously untreated steel or iron surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

Material and labour for preparing of new or previously untreated surfaces of wood of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

Material and labour for 50 mm thick cement concrete (1:2:4) type B-2 (using 40mm graded crushed stone aggregate) as in plinth protection finished even and smooth using extra cement (including necessary joint filling with mixture of paving bitumen and sand in (1:3)) complete all as specified and as directed.

Material and labour for TMT bars (Fe 500),10 mm dia and over in reinforcement cut to length, bent to shape required including bending spirally cranking, hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Material and labour for precast reinforced cement concrete (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in cover slab set in cement mortar (1:6) complete all as specified and as directed. Note: - Reinforcement shall be measured and paid separately.

NOTE NO 1: - Samples of materials as approved will be kept in GE's sample room. NOTE NO 2: - All fittings and fixtures mentioned above will be fixed to the satisfaction of Engineer-in-Charge and GE. NOTE NO 3: - Warranty certificate to the Engineer-in-Charge where ever applicable shall be submitted by the Contractor at the time of fittings.

M/S VED PAUL MAHAJAN (BID ID -3087703)

M/S Sukhmani Construction Co. (BID ID -3078824)

M/S TRIKUTA BUILDERS (BID ID -3078839)