Interior and Fit-out works of IIFCL office, E300, 3rd Floor at World Trade Centre, Tower-E, Nauroji Nagar, New Delhi-110029

Total (DSR+MR) or Estimated Cost put in the Tender 199,250,004.79

Digitally signed by RAJ PAL

SCHEDULE OF QUANTITIES - CIVIL WORKS

S NO DSR/MR DESCRIPTION QUANTITY UNIT RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR NON DSR

1 FLOORING WORKS

CEMENT CONCRETE: Providing and laying in position CEMENT CONCRETE of specified grade exluding the cost of centring and shuttering-all work upto plinth level.

4.1.8 1: 4: 8 (1 Cement: 4 coarse sand: 8 graded stone aggregate 40mm nominal size) 179.10 CUM 6812.00 1220029.20

RAISED FALSE FLOOR: Providing and fixing removable raised/false access flooring with systemand its components of approved make for different plenum height with

possible height adjustment upto 50mm, comprising of modular loadbearing floor panels supported on G.I. rectangular stinger frame workand G.I. Pedestal etc. all

complete, as per the architectural drawings, as specified and as directed by Engineer-in-charge consisting of:

(a) Providing at required spacing to form modular framework, pedestals made out of GI tube of thickness minimum 2 mm and 25 mm outer diameter, fully welded on to

the G.I. Base plate of size 100mm x 100mm x 3mm at the bottom of the pedestal tube, G.I. pedestal head of size 75mmx75mmx3.5 mm welded with GI fully threaded

stud 16mm outer diameter with two GI Check nuts screwed on the stud for level adjustment upto 50mm, locking and stabilizing the pedestal head in position at the

required level. The pedestals shall be fixed to the subfloor (base) through base plate using epoxy based adhesive of approved make or the machine screw with rawl

(b) Stringers system in all steel construction hot dipped galvanized ofrectangular size 570x20x30x0.80mm thick having holes at both ends for securing the stringers on

to the pedestal head using fully threaded screws ensuring maximum lateral stability in all directions, the grid formed by the pedestal and stringer assembly shall receive

the floor panel, this system shall provide adequate solid, rigid support for access floor panel, the system shall provide a minimum clear uninterrupted clearance

1.02 between the bottom of the floor for electrical conduits and wiring etc. all complete as per the architectural drawings, as specified and as directed by the Engineer-in-

(c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static high pressure Lamination of 800H grade (FS800H). Access Floor

panel shall be steel welded construction with an enclosed bottom pan with uniform pattern of 64 hemispherical cones. The top and bottom plates of Steel Gauges: top

0.6 mm and bottom 0.7 mm fused spot welded together (minimum 64 welds in each dome and 20 welds along each flange). The panel should be Corroresist epoxy

coated for lifetime rust protection and cavity formed by the top and bottom plate is filled with Pyrogrip noncombustible Portland cementitious core mixed with lightweight

foaming compound. The access floor shall be factory finished with Anti-static High Pressure laminate with Non Warp technology upto 1mm thickness for superior

adhesion and Surface flatness within 0.75mm.The panel is to withstand a Concentrated Load of 363 kgs applied on area 25mm x 25mm without collapse in the centre

of the panel which is placed on four steel blocks. The panel will withstand and Uniformly Distributed Load (UDL) minimum 1250 kg/sqm and an impact load of 50kg all

complete as per the approved manufacturers specification and as per the direction of Engineer-in-charge. All specification must be printed on the side of the panel to

ensure the quality of the product.

11.54.2 450mm Finished Floor Height (FFH). 48.50 sq m 5977.35 289901.48

ALUMINIUM SKIRTING: Supply of 100mm Aluminium (Grade 6063) Skirting with 15 micron anodising In Natural Finish. Thickness 1.30 to 1.50mm. Designed to

conceal screws. Seamless finish. Complete with Rubber/ PVC Jointers and Gasket.

ENGINEERED WOODEN FLOORING: Supplying and Installation of engineered wooden flooring of total thickness 13 mm -16 mm, Toplayer PEFC controlled Core

1.04 MR board PEFC controlled Backing layer PEFC controlled sources Wood Veneer 2 mm Tongue and groove Length Uniclic Width Uniclic Multifit Domestic use Conditions 481.50 sq m 6168.00 2969892.00

as per direction of engineer in charge.

VITRIFIED TILES: Providing and laying Vitrified tiles full body with smooth surface in floor (thickness 15 mm to be specified by the manufacturer), with water

absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified

quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, approved make Kajaria, Somany, RAK or equivalent. as per direction of

Engineer-in charge.

c MR Special Subway Tile 95.00 sq m 3563.00 338485.00

CARPET TILES: Providing and laying carpet tile flooring. Carpets shall be of Type 6 nylon loop pile carpet tiles/Plank. The carpet shall have sufficient gauge (1/10 ~

1/12) with sufficient stitches (10~13) per inch. The carpet shall be solution dyed fibre content or with injection printing technology. The carpet shall have the pile height

ranging from (2.0 ~ 3.0) mm with average density higher than 4500 Oz/ cubic yard. The total thickness of the carpet tile shall also range from (5.5 ~ 6.0) mm.

ITALIAN MARBLE: Providing and laying machine cut, mirror polished, Italian Marble brass brass inlay stone flooring laid in required pattern in linear portion of the

building all complete as per architectural drawings, with 18mm thick stone slab laid over 20mm (average) thick base of cement mortar 1: 4 (1 cement: 4 coarse sand)

1.07 MR laid and jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry admixed with pigment to match the marble shade including rubbing,

curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

18 mm thick Italian Marble stone slab in all colour and shade 358.00 sq m 6438.00 2304804.00

IPS FLOORING: 52mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4

graded stone aggregate 20 mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6

mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry,

but excluding the cost of nosing of steps etc. complete.

TOTAL FLOORING WORKS 2157175.35 9919859.18

Digitally signed by RAJ PAL

S NO DSR/MR DESCRIPTION QUANTITY UNIT RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR NON DSR

2 FALSE CEILING WORKS

GYPSUM BOARD CEILING: Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from

M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick

with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other

flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate

G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered

flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips

2.01 12.45 made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm

long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of

gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush

finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150

mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light

fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in

Charge but excluding the cost of painting with

12.45.1 12.5mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) 1098.38 sq m 1355.80 1489189.03

WOODEN VENEER CEILING: Providing and fixing wooden veneer ceiling by Fixing Natural OAK Veneer 4mm on 12mm underlay Fire retardant Ply fixed to a subframe

made using 50mmx50mm Kiln seasoned and chemically treated hollock wood fixed to RCC ceiilng using Fasteners.

POLISH: Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as

detailed below:

1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos.

2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs.

3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this

2.03 MR wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on 240.94 sq m 2467.00 594408.85

which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs.

4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion.This 1st coat is allowed to dry

for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor

pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete coat to be done in 1 or 2 layers without gap of time.) as

per direction of Engineer-in-Charge.

BAFFLE CEILING: Providing & fixing polylam blades vertical & horizontal baffle system, exhibiting space-delineating characteristics. The system comprises baffles

50mm wide & 100 Deep thickness of minimum 0.5mm GMS, installed at 150mm C/C. The C shaped shaped carrier rails run perpendicular to themain baffles profiles.

Individual baffle lengths between 300 and 2400 mm can be selected. Baffle are supplied with the end cap matching the similar finish of baffle. Tolerances according to

TAIM, DIN EN 13964 and quality controlled to ISO 9001:2015 approved by SIS. Substructure for POLYLAM®• Vertical baffle system consisting of C shape carrier of

minimum 1.2mmthickinstalled perpendicularly to baffles, same was hanged to wall with the help of wall anchor fasteners. Baffles to be connectedperpendicular to C

shaped carriers with the help of baffle hanger brackets. The primary profiles must be connected to oneanother with longitudinal splice connectors. C shaped baffle

carriers to be installed at maximum distance of 1200mm. in a length of 2400 mm baffles.Manufacturer shall have the fully automatic powder coating system with power

and free conveyorize 3mtr/minute capacity. Powder coating plant shall be equipped with latest modern technology with fully automatic inline Pre-treatment using nano

technology, Inline automatic water Drying system after pre-treatment. Mode of Measurements: Measurements shall be wall to wall without any deductions for lights,

diffuses, columns etc.. IN WOODEN FINISH

LINEAR OPEN CELL CEILING: Providing and fixing of Star 3 linear cell ceiling made out of Aluminium. The assembled cell ceiling panels shall be in size of 600x1200.

The assembled cell ceiling panels shall made out of main blades in 3mm (W) x 20mm (H) in 1200mm (L), installed at 30mm c.c. and cross connected to secondary

blades in 9mm(W) x 22mm (H) in 600mm (L) with 375mm pitch. The assembled cell ceiling panels are then clipped into U-94 carriers in Aluminium, pre-coated in black

2.05 MR enamelled finished at 1200mm c.c. Wire clips shall hold the cell ceiling panels into the U-94 carriers. Once the U-94 carriers are installed then primary angles made out 380.00 sq m 7538.00 2864440.00

of GMS, type U1040 are cross connected to the U-94 carriers at 1200mm c.c. for lateral bracing The whole ceiling shall be suspended by M6 threaded rods installed

100mm c.c.All panel modules must be hingeable through wire clips.Finish of cell ceiling panels: metallic silver in RAL 9006.

Digitally signed by RAJ PAL

S NO DSR/MR DESCRIPTION QUANTITY UNIT RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR NON DSR

WOOD GRILLE CEILING & WALL PANELLING: Providing & fixing of Knauf WoodWorks Grille with backer made of compressed natural bamboo with Knauf 24mm

Prelude 43 black exposed grid. The Grille panels shall be made of rapidly renewable natural bamboo core having density 600+Kgs/m3 as per BS EN323 (1993) and

bending strength of 96+ N/mm2 as per BS EN310 (1993). The Grille panel shall have a seven layer UV coating of thickness 0.09-0.11mm as per BS EN71 finished to

natural or carbonized shades. The Grille panel shall be of nominal size 35x300x2400mm comprising 8 blades/slats of 35x16x2376mm with centre to centre spacing of

37.5mm fixed through Backer of size 12x22x300mm having centre to centre spacing of 300mm and additional end backers at 150mm from both the edges. Ledger of

6.5x24x2400mm shall be used for covering face of wall angle. Open edges shall be covered using Edge Caps of 44x19x2400mm and Blade Junction of

66x38x2400mm shall be used along the connection of two Grille panels. The Grille panel when used with Knauf 20mm Optra Black Glasswool infill panels shall have an

NRC of 0.9 (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) as per ASTM C423. The Grille panel shall have a fire

performance of Class B according to EN13501-1. The Grille panel shall have moisture content of 8-14% as per IS 1708 (Part 1):1986 and a Humidity Resistance (RH)

SUSPENSION: The tile shall be installed on Knauf Prelude 43 Black with 24 mm wide T - section flanges having rotary stitching on all T sections i.e., the Main Runner,

1200 mm & 600 mm Cross Tees with a web height of 43mm, 35mm and 30mm respectively. The deflection loading of the system shall be 17.8 kg/m2 (as per standard

installation layout mentioned below) and main beam tested as per ASTM C635 (Deflection limit less than L/360) with a deflection loading of 21.4kg/m. The end details

of the main beam and cross tee shall be made of pre hardened steel fixed to the ends. The cross tee to provide double locking between “cross tee to cross tee” and

“cross tee to main beam”. All main beam to main beam and cross tee to cross tee connection shall have a pull out strength of more than 100kg. The T Sections shall

be made of hot dipped galvanized steel of 100 gsm as per IS 277 (2003) and pre-painted steel with baked polyester paint with 0T bending capability. All exposed panel

ends to be covered using edge caps. All wall angles to be covered using ledgers. Installation should be carried out as per Knauf recommended procedure. The grid

shall be installed with suspension system of Knauf make.

INSTALLATION: To comprise main runner spaced at 1200mm centre to centre securely fixed to the structural soffit using Knauf suspension system (specifications

below) at 1200mm maximum centre. The First/Last Knauf suspension system at the end of each main runner should not be greater than 450mm from the adjacent

Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm centre to form 1200 x 600 mm module. Cut cross tees longer than 600mm

require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees.

Perimeter trim to be Knauf wall angles of size 3000x19x19mm, secured to walls at 450 mm maximum centre to centre.

Metal spring backer clips shall be used to fix the Grille panel to suspension with a grid formation of 600mm along the blade/slat and 2 pieces along each backer (total 8

clips per full panel size) for every individual panel. Raise the panel up against the suspension system and align the backers with the suspension system. Push upwards

on the spring backer clip to engage the clip tabs on to the suspension system flange. Ensure that both clip tabs engage the suspension system flange.

KNAUF SUSPENSION SYSTEM accessories manufactured and supplied by Knauf consisting of M6 Anchor Fasteners with hanger hole, pre–Straightened Hanger wire

of dia – 2.5 mm of 1.80 m length having a tensile strength of 344-413 MPa and a minimum loading strength of 110 kgs. Additionally, adjustable hook clips made of

0.7mm thick Grade 1 C55 galvanized spring steel of dimension 100 x 20mm and 4 mm aquiline wire to be used for level adjustment during installation purpose in main

PERFORATED GYPSUM CORRIDOR CEILING: Supply and installation of Danoline acoustic self supporting ceilings – Corridor 400 - 9.5x400x1800mm high grade,

glass fibre reinforced, acoustic, white painted, gypsum panel with acoustic perforation,as Micro - round 6x6mm c/c 15mm type NRC - 0.70, Corridor 400 panels are

with integrated metal profile on the back, to be installed in free span without suspension hangers.

The tiles are furnished with a grey/white absorbent felt backing with an airflow resistance of 330-460 Ns/m³ (DIN 53887). RH - 90% LR - 82.6% Fire Class A2-s1,d0

2.07 MR SUSPENSION - The flex-profile is an integrated part of the Corridor ceiling plank. The suspension system from approved manufacturers consists of reinforced wall 240.66 sq m 5893.00 1418209.38

angles and 38mm main runners are used between sections and lines of Corridor planks.

Cleaneo Technology - Air purification & Air quality.Active reduction of air polluants thanks to Cleaneo Technology effectively reduces concentrations of VOC’s like

alcohol, aldehydes, ketons and esters as well as unpleasant odours from e.g. food or cigarette smoke. Air purification properties tested according to CEN standards

and VDI guidelines by Fraunhof Insistute for Building Physics

PERFORATED GYPSUM BOARD CEILING: Providing and fixing suspended false ceiling- Danoline: Solopanel Size 1188x1998x12.5mm Globe perforation 8/18 with

8.7% perforation with NRC upto 0.6 : Regular round perforation of glass fibre reinforced gypsum material, which includes providing and fixing GI perimeter channels of

size 0.55 mm. Thk. having one flange of 20 mm and another flange of 30 mm and web of 27 mm along the perimeter of the ceiling, screw fixed to brick wall/ partition

with help of nylon sleeves and screws, at 610 mm centers. The suspended GI intermediate channels of size 45 mm,0.9mm thk with two flanges of 15 mm each from

the soffit at 900 mm centers with ceiling angle of width 25mm x 10mm x 0.55mm thk fixed to soffit with GI cleat and steel expansion fasteners. Ceiling section of 0.55

mm thk having web of 51.5mm & two flanges of 26mm each with lips of 10.5mm are fixed to the intermediate channels with help of connecting clips and in direction

2.08 MR perpendicular to the intermediate channel with centers of 333 mm perforated gypboard is then screw fixed to ceiling section with 25 mm dry wall screws at 300 mm 243.26 sq m 3152.00 766768.13

centers to G.I. framing in perfect level. Screw fixing is done mechanically either with screw driver or drilling machine with suitable attachment. Finally the boards are to

be joined and finished so as to have a flush look with uniflot.

Cleaneo Technology - Air purification & Air quality.Active reduction of air polluants thanks to Cleaneo Technology effectively reduces concentrations of VOC’s like

alcohol, aldehydes, ketons and esters as well as unpleasant odours from e.g. food or cigarette smoke

Air purification properties tested according to CEN standards and VDI guidelines by Fraunhof Insistute for Building Physics.

The false ceiling surfaces shall be prepared to the satisfaction of the Architect, and shall be applied with two coats of primer to the satisfaction of Architects.

300x1200 SUSPENDED FALSE CEILING : Providing and fixing suspended false ceiling microlook tegular edge tile with 15 mm thickness ,easily demountable tile,

manufactured from High density glass wool , visible surface is a batch painted glass tissue in white, back of the tile covered with glass tissue. Size 1200x600x15mm

Acoustics-Sound absorption(Alpha W) - 0.95 at 200 mm o.d.s as per EN ISO 354 Acoustics-Sound absorption Class - Class A at 200 mm o.d.s as per EN ISO

2.09 MR 11654Acoustics-Articulation class - 180 as per ASTM E1111, ASTM E1110,NRC - 0.9 NRC as per ASTM C 423,Humidity Resistance -Permanent ambient RH up to 304.43 sq m 3084.00 938862.12

95% at 30*C without sagging, warping and delaminating ( 13964:2014). Fire Safety - Tested and classified as non combustible according to EN ISO 1182 with reaction

to fire classification class A2 s1 d0 according to EN 13501-1 - European Standard.

TOTAL FALSE CEILING WORKS 1489189.03 12637354.50

Digitally signed by RAJ PAL

S NO DSR/MR DESCRIPTION QUANTITY UNIT RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR NON DSR

3 WALL FINISHES WORKS

GLASS PARTITION (FIXED DOUBLE GLAZED GLASS PARTITION): Supply & Installation of Aluminum profile with top & bottom profiles of size 82mm x 38mm in

Natural Anodized / Black finish. Partition sides to be fixed with mullion and it's covers should be easily accesible while removal of glass, if & when required. Glass to be

fixed with suitable EPDM gaskets for insertion of combination of 10mm thick clear toughened glass + 58 to 62 mm Air Gap + 12 mm thick clear Toughened Glass.

Glass should not placed directly on profiles for giving more strength. It should be placed on aluminium spacer profiles and spacers should be covered with cover

profiles. Partition Glass joineries consists of two-way Polycarbonate I-profiles, 90 Degree Polycarbonate L-Junction and Polycarbonate T-Junction profiles.

Polycarbonate profile joineries to be fixed with double sided adhesive tape & profiles to be inserted in the joint instead of sealing it with sealants. Polycarbonate profiles

to be used to give continuity glass effect. Hardware for fixing profiles to be used as per manufacturer standard. Profile & hardware should be from same brand to give

end to end solution. Costs should be inclusive of necessary Hardware for fixing of profiles & installation charges.

FRAMED HINGED GLASS DOOR: Supply & Installation of Framed Hinged Door with Profile size of 55x32mm along with necessary seals. Doors to be fixed on Hinges

& Lock with lever handle for rebated door in matt black/ natural Alu finish with Top Mounted Door Closer along with Slide Channel on Top and saddle plate for fixing on

3.02 MR the Glass door suitable for 10mm thick clear toughened glass. Necessary seals to be provided all around the doorframe. Necessary Hardwares includes Lock with 65 Nos. 75381.00 4899765.00

Lever Handles, Seals, Hinges & door closers as per manufacturer's standard. Installation rates should be inclusive and vendor shall provide end to end solution.

WOODEN DOOR FRAMES: Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold

3.03 fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).

9.1.1 Second class teak wood 0.26 cu m 142949.70 37309.87

WOODEN BATTENS: Providing and fixing specified wood frame work consisting of battens 50x25mm fixed with rawl plug and drilling necessary holes for rawl plug etc.

3.04 including priming coat complete.

8.27.1 Kiln seasoned and chemically treated hollock wood 1 CUM 187277.65 187277.65

FLUSH DOOR SHUTTERS: Providing and fixing on all height prefabricated factory made 40mm thick flush door shutter in existing door frame bounded with BWP type

synthetic resin adhesive & wooden fillers as per IS 848 -1974 shutter should be confirm IS:2202 (part-1) non decorative type flush door of area up to 1.80 to 2.50 sqm

and nothing shall be paid on account of size variation upto 5% plus mimus of make Greenlam, Duro, Century or Equivalent with both side 4mm thick decorative teak

veneering of make sapele/white american oak/vintage teak including fixing on all edges 8mm thick second class teak wood margin/lipping with 8 mm thick clear

vision/frosted glass fitted vertically in flush door shutter of make Saint Gobin, Modi Guard & Hindustan National Glass fixed all-round by 4mm thick second class teak

wood margin/molding and size of cut in flush door shutter will be approx. 200x1800mm or as per approved drawing and one no. of door rubbershutter finished

complete with PU polish all-round i/c SS butt hinges and SS screws all complete as per the direction of engineer-in-charge. (Note: this item is inclusive of all material,

T&P and labour involved and the work shall be executed as per the approved drawing).

WOODEN LIPPING: Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door

shutter to be measured).

FLUSH DOOR FLOOR MACHINE : Providing Double cylinder Floor Spring D-120 for Wooden door with Closing Force EN 4 with Maximum door weight 120 Kg.

3.07 MR Maximum door width 1250 mm.Closing speed : 130° Final closing speed : 15-0°. Hold Open (standard): 90° hold open. Weight of floor spring approx : 6kg, 5,00,000 6 SET 15039.00 90234.00

cycles Tested. approved make and model all complete as per the direction of Engineer-in-charge.

3.08 MR TOP & BOTTOM STRAP : Providing top and Bottom Strap for wooden doors of approved make and model all complete as per the direction of Engineer-in-charge. 6 SET 748.00 4488.00

FLUSH DOOR DEAD LOCK : Providing and Fixing 160 mm Euro Dead lock with Rose rings for wooden doors of approved make and model all complete as per the

direction of Engineer-in-charge.

FLUSH DOOR LOCK CYLINDER : Providing and Fixing 60 mm Eco Pin Cylinder 1CK SS Cylinder One side knob and one side regular key for wooden doors of

approved make and model all complete as per the direction of Engineer-in-charge.

FLUSH DOOR HANDLE : Providing 32x840 mm SS 304 H type Handle for wooden doors. Material : Stainless Steel.

Finish : Satin Stainless Steel (SSS). of approved make and model all complete as per the direction of Engineer-in-charge.

WOODEN DOOR LOCK: Providing and Fixing Dead lock Back set- 50 mm with Key Hole of approved make and model all complete as per the direction of Engineer-in-

GLASS FILMS: Providing & Fixing Frosted Translucent, cast PVC, self-adhesive vinyl, special CRYSTAL-effect film to reproduce Sand-blasting effect on glass with

customised designs, thickness of 2 mil (0.05mm) without adhesive & 3mil (0.8) with adhesive having minimum tensile strength of 3.5 pound/inch at 73 F (0.6 kg/cm at

23 C). Adhesion after 24hrs of installation should be 4 pounds/inch (0.7 kg/cm) on Acrylic, Glass Polycarbonate: MCS warranty of 3yrs (if exposed to direct sunlight) to

15yrs (indoors).

TOILET DOOR MORTIZE LOCK: Providing and Fixing ss 304 D Type Tube Lever Mortise Combi SET with 60 mm Cylinder keyless and Lock Body SS for wooden

Toilet doors of approved make and model all complete as per the direction of Engineer-in-charge.

TOILET DOOR LOCK BODY : Providing and Fixing 240 mm lock body for wooden doors of approved make and model all complete as per the direction of Engineer-

Digitally signed by RAJ PAL

S NO DSR/MR DESCRIPTION QUANTITY UNIT RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR NON DSR

TOILET DOOR CLOSER : Providing and Fixing Door closer Hercules -60 kg for wooden doors of approved make and model all complete as per the direction of

Engineer-in-charge.

TOILET DOOR HINGES : Providing and Fixing SS 304 Hinges Four Ball Bearing 100x75x3 mm (with screws) for wooden doors of approved make and model all

complete as per the direction of Engineer-in-charge.

LACQUERED GLASS: Providing and fixing of 6mm thick annealed SGG Planilaque Evolution (premium GRIHA rated lacquered glass from Saint-Gobain) of approved

color by Architect/ Client / Customer, fixed with SGG ULTRAFIX (compatible neutral core silicon/ double sided tape) on a perfectly leveled 12mm thick water proof

marine plywood / MDF / Mineral fibre board which is mounted on the RCC wall/any other structure. Lacquered glass must be made industrially (via curtain coating

3.18 MR process); opaque (if viewed against a support wall), coated with PU lacquer (50 micron thick); color consistency (measured by Minolta spectrophotometer CM5081); 362.39 SQM 5004.00 1813418.33

highly durable (passes PERSOZ hardness test for minimum 220 oscillatios); humid resistant (conforms to BS EN 1036 1999); environmentally friendly (no lead, no

arsenic, no copper, noformaldehyde); appropriate recycled content (12% post industrial/ 6% post consumer); compressive strength (1000 MPa) & tensile strength (40

MPa), same as float glass;

GYPSUM BOARD PARTITION: Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame

work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm

wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia

meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48mm wide having one flange of 34 mm and other flange 36 mm and

0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing

9.105 of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450mm centre to centre, and fixing

3.19 of boards to both side of frame work by 25mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300mm centre to centre. The boards are to be

fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99mm width (0.9mm thick having two flanges of 9.5mm each) to be

provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with

recommended jointing compound, jointing tape, angle beads at corners (25mmx25mmx0.5mm), joint finisher and two coats of primer suitable for board as per

manufacturer's specification and direction of engineer in charge all complete.

75mm overall thickness partition with 12.5mm thick double skin fire rated Glass Reinforced Gypsum (GRG) plaster board conforming to IS: 2095: part 3 (Board with BIS

certification marks)

ACRYLIC SOLID SURFACE CLADDING: Supply & Installation of 12 mm thick Thermoformable Acrylic Solid Surface Sheets (DuPont Corian/ Tristone/ Lotte), over a

robust substrate made out of BWP/ Flexi Ply/ MS- Aluminum sections etc. as required, to achieve stated design intent. ASS in 12mm thickness, shall be manufactured

as per guidelines of ISO 19712. ASS sheets to be cut, pasted and finished over the substrate as provided, to achieve smooth and seamless finish. Item cost include

intend adaptation, supply, freight and installation of ASS sheets to site, wastage, finishing, creating provisions/ cut-outs for accessories and final placement of table.

Work shall be done by company's authorized Quality Network (QN) fabricator, as per satisfaction of Engineer-in-Charge. Colours : Basic, Solid and small speckled

WINDOW BLINDS : Providing & supplying of fabric venetian Window Blinds as per the approved sample, consisting of 3" vane size having head rail, rotator rail and

bottom rail made of aluminium alloy 6063-T6 PER ASTM B221 - 85 extruded profile, powder coated and provided in standard natural white color. The rolling tube

should be made up of aluminium alloy from extruded profile of 34mm dia. The head rail dimensions should be of suitable size according to the length of head rail and

space available and finished with fabric cover matching with the louver fabric. The cassette should conceal the working mechanism rotary-clutch. (White polycarbonate

spring tempered rotary clutch which raises), lower and tilts the blinds. White polycarbonate limit assemblies control vane over-rotation, located on either side of

3.21 MR individual blinds. The room darkening fabric of Blind should be of anti-static polyester vanes which have facings between two sheer layers (50 mm wide) to reduce 156.75 SQM 10793.00 1691802.75

glare. Sheer layers should be of white 100% knit polyester, the colors, textures and opacities as approved. The fabric shall be made of spun- bonded 100% polyester

fiber (having green guard certification) treated with soil & dust repellent requiring minimum regular interval cleaning. GREEN GUARD Gold certified for low-emitting

products to maintain Indoor environment. Up to 80% ultraviolet protection with vanes open and 90% with vanes closed. The shading to be operated by Easy rise

mechanism with a continuous cord loop operating system. All parts, components & hardware are in approved shade as per direction of Engineer-incharge.

PELMET: Fabricate and install pelmet made of 19mm thick board, up to 300mm high and in line with external glazing as per details of Architect. Rate to include

finishing exposed surfaces of the Pelmet with 1mm laminate.

ZINC CLADDING : Supply & Installation of ZINC Titanium (conforming to EN 988 stndards) Interlocking wall cladding panels in VMZINC Pigmento Finish. The wall

cladding system shall comprise of the following as described .ZINC 0.8 mm interlocking panels of 233 mm width and max 2000 mm length. Panels are formed with

interlocking lap at panel edges and smooth, flat pan; designed to be field assembled in sequential installation by engaging edges of each panel to edge of adjacent

3.23 MR panel. Panels are attached to supports/substrates using stainless screws located under edges of the panels The Panels Shall be Installed over the Aluminium box 11.25 SQ M 17269.00 194276.25

Section of 50x25x1.6 mm thick @ 600mm c/c horizontal and vertical with Screws/ Rivets of suitable size as recommended by manufacturer .THe zinc titanium

manufacturer shall have regisetered office in India and shall have supplied zinc titanium cladding to government projects in last 5 years . Installation to be carried out by

manufacturer approved installation agencies who has completed zinc cladding projects in India.

3.23a MR Supply & Installation of ZINC Flashings in same finish and material for corners, top, botom, site detailing 6.00 RM 3139.00 18834.00

3.24 13.26 Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete 100.00 sqm 262.70 26270.00

Digitally signed by RAJ PAL

S NO DSR/MR DESCRIPTION QUANTITY UNIT RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR NON DSR

13.85 Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.

13.85.3 With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre 100.00 sqm 73.95 7395.00

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the

surface even and smooth complete.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and

13.83 manufacture, including applying additional coats wherever required to achieve even shade and colour

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing

3.29 and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge.

14.1.2 With cement mortar 1:4 (1cement: 4 coarse sand) 100.00 Sqm 560.50 56050.00

5.5mm THICK HDHMR BOARD (BOTH SIDE RAW): Providing and fixing in wall lining, partitions etc. Confirming to ASTM E-84-2021 class1 BOTH side raw, having

even grade low emission, high moisture resistance, fire resistance, borer, termite & fungus resistance, green material and environmental friendly with necessary fixing 50.00 Sqm 504.00 25200.00

arrangement and screws etc. , complete as per direction of Engineer-in-Charge

5.5mm thick HDHMR Board

11 mm THICK HDMR BOARD ( BOTH SIDE RAW ): Providing and fixing 11mm thick HDHMR board in wall lining, partitions etc. both side raw. Extra density, high

3.31 MR moisture resistance, borer, termite & fungus resistance, green material and environmental friendly with necessary fixing arrangement and screws etc. Complete

11 mm thick HDHMR Board 3705.36 SQM 1079.00 3998083.44

5.5mm THICK HDHMR BOARD ( ONE SIDE LAMINATE ): Providing and fixing in wall lining, partitions etc. Confirming to ASTM E-84-2021 class1 one side 1mm

decorative Lamination and other side raw, having even grade low emission, high moisture resistance, fire resistance, borer, termite & fungus resistance, green material

and environmental friendly with necessary fixing arrangement and screws etc. , complete as per direction of Engineer-in-Charge

5.5mm thick HDHMR Board 3100.22 SQM 720.00 2232155.70

ALUMINIUM FRAME: Providing and fixing partition, frame work in 50x25x1.5mm Aluminium Section placed at 600mm centre to centre both ways (horizontal & vertical)

3.33 MR fastened to floor, ceiling and horizontal member. The item includes providing and fixing 50mm thick polyester synthetic insulation as insulation of 100 GSM. 1852.68 SQM 1347.00 2495559.96

FIBRE WALL COVERING: Supply & Installation of Glass fiber based homogenous Woven/ non-woven .1mm thick, 100-200 GSM Density brethable Wall Coverings.

Material to be fire certified with minimum Euroclass BS1D0 certification under EN13501, no harmful chemical coated with Oekotex Standard 100 certification and non-

3.34 MR toxic in nature for closed enviornments with A+ attested for emission in indoor air. Installation to be done over smooth, dry and dust-free substrate as specified with 177.50 SQM 1508.00 267670.00

OEM recommended adhesive by the supplier's authorized installer team. Installation measurement as per the entire area (concealed/visible) installed. Finished as per

satisfaction of E.I.C. PAINTABLE

ITALIAN MARBLE FOR WALL CLADDING: Providing and laying machine cut, mirror polished, Italian Marble of 18mm thickness for wall in linear portion of the building

all complete as per architectural drawings, laid over 20mm (average) thick base of cement mortar 1: 4 (1 cement: 4 coarse sand) laid and jointed with white cement

slurry admixed with pigment to match the marble shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-

3D ACOUSTIC PET WALL PANELLING: Providing and fixing Smart Acoustical Wall Panels with square edges made of Polyester fiber substrate 12mm thick with

acoustical properties and with an option of 12 colours as per the choice of the Architect/ Person in-charge, providing a minimum sound absorption level of 0.50-0.90

NRC, to be affixed to wall using Adhesive. The material should adhere to Formaldehyde emission standards of GB18580-2001 class E1, asbestos-free, non-toxic, non-

irritant and recyclable. Material to have fire resistance as per B1 Chinese standards. The sheets to have density of 200 kg/m3 and weight of 2.0 kg/m2. The sheets to

be made available as per the V groove design approved by Architect/ Person in charge(attached Pic). Cutting to be in done by supplier using blade cutting as per

LAMINATE PANELLING: Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective

3.37 surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.

TOTAL WALL FINISHING WORKS 6945065.85 25644407.50

Digitally signed by RAJ PAL

S NO DSR/MR DESCRIPTION QUANTITY UNIT RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR NON DSR

4 MISCELLANEOUS WORKS

MODULAR KITCHEN - UNDER COUNTER STORAGE CABINETS:

Modular kitchen - Under counter storage cabinets:

Providing & fixing factory made modular kitchen cabinets in modular type knockable cabinet boxes with openable shutters and sufficient number of drawers made of 18

mm thk.HDHMR board with lamination in frosty white laminate with 0.8 mm laminate complete with 0.8 mm edge banding.All shelves should be supported on approved

quality SS pins and shall be adjustable for different heights as per requirements.Shutters and drawers fascia shall be at least 18mm thic with laminate on both sides

4.01 MR with 18mm wide 2mm thick PVC edge banding, All Shutters/ drawers finished in high gloss acrylic of approved make- Rehau,Ornare,Senosan and having handless 16.65 SQM 21994.00 366200.10

profiles.The cabinet boxes of floor units will be supported by 100mm height vertical adjustable legs (Hettich make) which will be covered with PVC skirting (Rehau or

equivalent make) in brushed aluminum finish attached by hardware of skirting. The unit shall be fixed to the floor/ wall/slab using metal screws of appropriate size and

raw plugs. Only front face area of cabinets and skirting from floor to top of boxes shall be considered for measurement and payment. Cabinet boxes size would be

varies from 400x580x710MM to 1000x580x710MM (approx.) and join together as per site requirements etc. Handle Profile, Aluminum Handle Profile for lift ups, O*

Hinges, Corner Hinges, PVC legs, Skirting, Connector, Screws, Wall Mount set complete all as per the direction of Engineer-in-Charge.

MODULAR KITCHEN - OVERHEAD STORAGE WALL UNITS:

Modular Kitchen - Overhead storage wall units:

Providing & fixing factory made modular kitchen cabinets in modular type knockable cabinet boxes with openable shutters and sufficient number of drawers made of 18

mm thk. HDHMR board with lamination in frosty white laminate with 0.8 mm laminate complete with 0.8 mm edge banding.All shelves should be supported on approved

quality SS pins and shall be adjustable for different heights as per requirements.Shutters and drawers fascia shall be at least 18mm thic with laminate on both sides

with 18mm wide 2mm thick PVC edge banding, All Shutters/ drawers finished in high gloss acrylic of approved make- Rehau,Ornare,Senosan and having handless

profiles. The unit shall be fixed to the floor/ wall/slab using metal screws of appropriate size and raw plugs. Only front face area of cabinets and skirting from floor to

top of boxes shall be considered for measurement and payment. Cabinet boxes size would be varies from 400X320X710MM to 1000X320X710MM (approx.) and join

together as per site requirements etc. Handle Profile,Aluminum Handle Profile for lift ups,O* Hinges,Corner Hinges,PVC legs,Skirting,Connector,Screw,Wall Mount set.

Complete all as per the direction of Engineer in Charge.

4.02A MR Providing and fixing of Innotech with metal sides and quadro channels .Make.Hettich,Samsung,Irex,Hafale 10 Each 7943.00 79430.00

4.02B MR Providing and fixing of Bottle pulout 200mm. Make Hettich, Samsung,Irex,Hafale 3 Each 12335.00 37005.00

WATERPROOFING: Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of:

(i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off

junction of vertical and horizontal surface.

(ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction

of vertical and horizontal surface.

(iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area.

(iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

SHOP DRAWINGS: Preparation of complete set of shop drawings including finishing, MEP services, details, design calcualtions etc. and for prepration of as built

4.04 MR drawing any other details as and when desired by Engineer Incharge/ client. A qualified professsional for the purpose shall be appointed after due appproval from 1.00 LS 2000000.00 2000000.00

Engineer-In-Charge.

Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to

4.05 1.1.18 approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge. Note - item to be applicable in urban areas 10.00 cum 494.10 4941.00

having directions for restricted hours for movement/ plying of load carrying motor vehicle of 3.5 cum or more.

4.1. Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

4.1.3 1:2:4 (1 cement : 2 coarse sand (zone-lll) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) 5.00 cum 7878.50 39393.00

5.9 Centering and shuttering including strutting, propping etc. and removal of form for

5.9.1 Foundations, footings, bases of columns, etc. for mass concrete 9.00 sqm 392.15 3529.00

5.22A Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. 10.00 kg 107.85 1079.00

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in

6.4.1 Cement mortar 1:4 (1 cement : 4 coarse sand) 8.89 cum 9344.35 83071.00

6.13 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.

6.13.1 Cement mortar 1: 3 (1 cement: 3 coarse sand) 10.00 sqm 1150.50 11505.00

DEMOLITION & DISMANTLING WORKS

Demolition of brickwork manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per

the direction of the engineer in charge

4.12 15.12.2 Dismantling door, windows and clerestory widows (steel or wood) shutter including chowkats, architrave, holdfasts etc complete and stacking within 50 metres lead 5.00 Nos 502.75 2513.75

Digitally signed by RAJ PAL

S NO DSR/MR DESCRIPTION QUANTITY UNIT RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR NON DSR

AUTOMATIC DOUBLE SLIDING DOOR : Supply and installation of Automatic Double Sliding door (1800x3000mm) operator ES 250 Pro Easy 4150mm opearator with

double Sliding compliant with European standards and produced according to the guidelines for power-operated windows, doors and gates, BGR 232, the UVV and

the VDE regulations. TÜV design tested for 1 Million Cycle of opeartion in accordance with low voltage guidelines of IEC /EN 60335-2-103 and fulfils EN 16005 and DIN

18650-1 / DIN 18650-2 standards. The Profile Finish should be Silver Anodized E6/C0, with operator dimensions (H x D) not exceeding 150 x 180 mm and of length as

required to suit the opening size given below. dormakaba ES250 Pro Easy Operators are with very sturdy design , Self balancing Panel suspension system and with

Anti-Jump fitting. The track profile should be separate from the main profile for enabling reduction in vibration insulation, With Optional backplate for easy Installation.

16 bit intelligent Microprocessor-controller unit should be handled without any external handheld unit , Self-learning, with adjustable parameters for opening and closing

speed with an incremental value of 10cm/sec , Max. 30 Sec. hold-open time and opening and closing force, reversing when obstruction is encountered, with SMPS,

4.13 MR Class of protection IP 20. The Max. opening and close force by the opeartor should not exceed 150N and Max. Power consumption doesnot exceed 180W during 2.00 Nos 299977.00 599954.00

opeartion mode. The operator is used with EM failsafe lock The optional activators are via Nemo Combi sensor sensor with 2x Microwave for activation and double

rows of 24 spots failsafe Safety infra curtains without the need of Photocell. Program Switch with Knob, ES 250 Pro Easy, Max Panel Weight Carrying Capacity of 2 X

125 Kgs. The system shall have constant power supply 230V+ 5%, 50Hz, AC. The Opeartor is combined with dormakba ST-Flex Profile System suitable to hold 12mm

Toughned Glass with correct size of rubber gaskets. The profile size not exceeding 30x47 mm and ST Flex has Valid Environmental Product Declartaion Certification

as per ISO 14025 and 15804. The Operator assembly / production units must fulfill valid quality management systems of ISO 9001: 2015 and also have Environmental

Management System of ISO 14001: 2015 Certifications for product approval.Automatic door operator includes Key Programme switch , cable, Both side sensor, EM

Providing & fixing Danoline Access Panel of size mentioned below having - 1. Outer aluminium frame - thickness : 1.5mm ( plus 0.2mm thick powder coating) Material

: ENAW6063. 2. Inner Aluminium frame - thickness: 1.5mm (plus 0.2mm thick powder coating) Material : ENAW6063. 3. Corner fittings, inner frame - material: Hot

dipped galvanized steel plate Thickness 2.0mm, with zinc Coating of 200g. 4. Corner fittings, outer frame - material: Hot dipped galvanized steel plate Thickness

2.0mm, with zinc Coating of 200g. 5. 12mm plasterboard ( Knauf Brand) Type: moisture resistant ( MR) in green plasterboard liner. 6. Screw ( self - drilling black

phosphate ) - Material: mild steel C1018 - 1022. 7. Sealing strip, width, thickness - width: 9.0mm, thickness: 4.0mm. 8. Snap Lock ( spring catch/ catch lock ) - Type of

lock: touch latch, Material of lock: plastic ABS, cold rolled steel Q235. 9. Hinge - Thickness : 4.0mm, Length: 82mm; Material: SS2172 ( cold drawn steel wire ). 10.

Powder coating - Color: white, RAL 9010

Providing & fixing Danoline Access Panel of size mentioned below having - 1. Outer aluminium frame - thickness : 1.5mm ( plus 0.2mm thick powder coating) Material

: ENAW6063. 2. Inner Aluminium frame - thickness: 1.5mm (plus 0.2mm thick powder coating) Material : ENAW6063. 3. Corner fittings, inner frame - material: Hot

dipped galvanized steel plate Thickness 2.0mm, with zinc Coating of 200g. 4. Corner fittings, outer frame - material: Hot dipped galvanized steel plate Thickness

4.15 MR 2.0mm, with zinc Coating of 200g. 5. 12mm plasterboard ( Knauf Brand) Type: moisture resistant ( MR) in green plasterboard liner. 6. Screw ( self - drilling black 2 Nos. 4290.00 8,580.00

phosphate ) - Material: mild steel C1018 - 1022. 7. Sealing strip, width, thickness - width: 9.0mm, thickness: 4.0mm. 8. Snap Lock ( spring catch/ catch lock ) - Type of

lock: touch latch, Material of lock: plastic ABS, cold rolled steel Q235. 9. Hinge - Thickness : 4.0mm, Length: 82mm; Material: SS2172 ( cold drawn steel wire ). 10.

Powder coating - Color: white, RAL 9010 : 600x600

Providing & fixing Danoline Access Panel of size mentioned below having - 1. Outer aluminium frame - thickness : 1.5mm (plus 0.2mm thick powder coating) Material :

ENAW6063. 2. Inner Aluminium frame - thickness: 1.5mm (plus 0.2mm thick powder coating) Material : ENAW6063. 3. Corner fittings, inner frame - material: Hot

dipped galvanized steel plate Thickness 2.0mm, with zinc Coating of 200g. 4. Corner fittings, outer frame - material: Hot dipped galvanized steel plate Thickness

2.0mm, with zinc Coating of 200g. 5. 12mm plasterboard ( Knauf Brand) Type: moisture resistant ( MR) in green plasterboard liner. 6. Screw ( self - drilling black

phosphate ) - Material: mild steel C1018 - 1022. 7. Sealing strip, width, thickness - width: 9.0mm, thickness: 4.0mm. 8. Snap Lock ( spring catch/ catch lock ) - Type of

lock: touch latch, Material of lock: plastic ABS, cold rolled steel Q235. 9. Hinge - Thickness : 4.0mm, Length: 82mm; Material: SS2172 ( cold drawn steel wire ). 10.

Powder coating - Color: white, RAL 9010

Providing & fixing Danoline Access Panel of size mentioned below having - 1. Outer aluminium frame - thickness : 1.5mm (plus 0.2mm thick powder coating) Material :

ENAW6063. 2. Inner Aluminium frame - thickness: 1.5mm (plus 0.2mm thick powder coating) Material : ENAW6063. 3. Corner fittings, inner frame - material: Hot

dipped galvanized steel plate Thickness 2.0mm, with zinc Coating of 200g. 4. Corner fittings, outer frame - material: Hot dipped galvanized steel plate Thickness

2.0mm, with zinc Coating of 200g. 5. 12mm plasterboard (Knauf Brand) Type: moisture resistant (MR) in green plasterboard liner. 6. Screw (self-drilling black

phosphate) - Material: mild steel C1018 - 1022. 7. Sealing strip, width, thickness - width: 9.0mm, thickness: 4.0mm. 8. Snap Lock (spring catch/ catch lock) - Type of

lock: touch latch, Material of lock: plastic ABS, cold rolled steel Q235. 9. Hinge - Thickness : 4.0mm, Length: 82mm; Material: SS2172 (cold drawn steel wire). 10.

Powder coating - Color: white, RAL 9010

CUSTOMISED STORAGE UNIT: Supply and fixing of full height storage units (upto 450mm depth) made out of 18mm plywood finished with approved .8mm laminate

4.18 MR on the inside and outside. Hardware used of Hettich make.Compleate as per the direction of Engineer in charge 74.00 SQM 26726.00 1977724.00

FIRE GLASS WITH FRAME - Supply & Installation of Frame with Glass , Firetech cold- formed steel frame with 120 minutes of integrity and radiation control (EW120).

The system confirms to IS:3614 (Part II) or EN 1634-1:1999, tested and certified. The frame shall be finished with a approved fire resistant primer or powder coating in

desired shade as per the direction of Engineer- incharge. Glass - The glass should be 13mm clear 120 min fire rated for integrity, Radiation control (EW120) and partial

insulation (EI30), Non wired toughened interlayed glass with a light transmission of 86%, U-value of 5.0W/Sqmt K, solar factory of 0.72, energy transmission 66% and a

sound reduction of 38 (-1, -2) dB and compliant to class 1 (B) 1 category of Impact resistance as per EN 12600. The glass shall provide bi-directional (Symmetrical) fire

MOTOR FOR BLINDS - Providing and fixing of powerView AC Silent Motor with noise level of 40dB operating on Pebble Remote for better ergonomics having 6

channels for multiple shades operation. It comes with a Built- In Dry contact input pot on the motor head for low voltage automation convenience. The remote and

4.20 MR motor operate on a frequency which is 2.4 Ghz used for regular civil operation. Motor embedded with advanced features and technology of voice enabled control if 30 Nos. 20000.00 600000.00

used along with Hub and WiFi Nominal Torque (Nm): 3 Output Speed: 30 rpm Limit switch turns: 160 revolutions Mains Voltage: 230V / 50Hz, Power Consumption: 90

W Nominal Current Consumption (A): 0.39 Operating Mode: 4 Min Degree of Protection: IP 44

Digitally signed by RAJ PAL

S NO DSR/MR DESCRIPTION QUANTITY UNIT RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR NON DSR

BLINDS REMOTE - Providing and programming of Pebble remote that comes in ten different colours that is used to move blinds UP, DOWN, START and STOP with

4.21 MR single comand. It comes with six different channels with each channel can have upto 4 blinds paired. It also has favourite button to set favourite blind position and all 12 Nos. 4000.00 48000.00

blinds paired with the remote goes to favourite position with single click. All the keys in the remote lights up once touched.

TOTAL MISCELLANEOUS WORKS 162489.55 6668247.35

Digitally signed by RAJ PAL

SCHEDULE OF QUANTITIES - SANITARY & PLUMBING WORKS

S NO DESCRIPTION UNIT QTY RATE

2023/ MR AMOUNT AMOUNT

Supply, Installation, Testing and Commisioning of SINGLE LEVER CONCEALED BASIN MIXER

(WALL MOUNTED) WITH SPOUT (COMPOSITE ONE PIECE BODY)

MR 2 Supply, Installation, Testing and Commisioning of TABLE TOP BASIN, SIZE: 630x460x130mm EACH 1 20890.00 20890.00

Supply, Installation, Testing and Commisioning of suitable compatible WASTE COUPLING 32MM-

FULL THREAD- WITH CERAMIC CAP-*130MM HEIGHT *65MM CERAMIC CAP

Supply, Installation, Testing and Commisioning of BOTTLE TRAP (WITH INTERNAL PARTITION)

32mm SIZE WITH 300mm & 190mm LONG WALL CONNECTION PIPES & WALL FLANGE

Supply, Installation, Testing and Commisoning of RIMLESS, BLIND INSTALLATION WALL HUNG

MR 5 WC WITH UF SOFT CLOSE SLIM SEAT COVER, HINGES AND ACCESSORIES SET, SIZE: EACH 1 15087.00 15087.00

MR 6 Supply, Installation, Testing and Commissioning of PNEUMATIC CONTROL PLATE EACH 1 6641.00 6641.00

MR 7 Supply, Installation, Testing and Commisoning of ANGULAR STOP COCK WITH WALL FLANGE EACH 1 4823.00 4823.00

Supply, Installation, Testing and Commissioning of CONCEALED STOP COCK WITH ADJUSTABLE

WITH WALL FLANGE 15mm

Supply, Installation, Testing and Commisiong of HAND SHOWER (HEALTH FAUCET) WITH 8mm

DIA 1.2 METER LONG FLEXIBLE TUBE AND WALL HOOK ALD-CHR-573 or equivalent

Supply, Installation, Testing and Commisiong of PNEUMATIC SINGLE PIECE SLIM CONCEALED

MR 10 CISTERN BODY WITH INSTALLATION KIT & “S-TYPE” DRAIN PIPE CONNECTION SET FOR EACH 1 8044.00 8044.00

WALL HUNG WC (WITHOUT FLUSH CONTROL PLATE)

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

17.28.2 Flexible pipe

Providing and fixing mirror of superior glass (of approved quality) complete with 6mm thick hard board

ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing C.P. brass angle valve for basin mixer and gyser points of approved quality

13 conforming to IS : 8931

18.53.1 15 mm nominal bore EACH 8 574.30 4594.40

Cutting chases in brick masonry walls for following diameter sand cast iron/centrifugally cast (spun)

iron pipes and making good the same with cement concrete 1:3:6 (1 cement: 3 coarse sand: 6 graded

14 stone aggregate 12.5 mm nominal size) including necessary plaster and pointing in cement mortar

1:4 (1 cement : 4 coarse sand) :

18.76 Cutting holes upto 30x30cm in walls including making good the same.

18.76.1 With common burnt clay F.P.S. (non modular) bricks EACH 2 416.80 833.60

Making chases upto 7.5 X 7.5 cm in walls including making good and finishing with matching surface

after housing G.I. pipe etc.

Digitally signed by RAJ PAL

S NO DESCRIPTION UNIT QTY RATE

2023/ MR AMOUNT AMOUNT

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot &

cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with

clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent

cement and testing of joints complete as per direction of Engineer in Charge.

Internal work - Exposed on wall

18.7.2 20mm nominal outer dia pipes METRE 20 335.00 6700.00

18.7.3 25mm nominal outer dia pipes METRE 20 401.55 8031.00

18.7.4 32mm nominal outer dia pipes METRE 5 518.75 2593.75

18.7.5 40mm nominal outer dia pipes METRE 5 702.95 3514.75

18.7.6 50mm nominal outer dia pipes METRE 5 934.15 4670.75

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot &

cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at

1.00 m spacing.

This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting

chases and making good the same including testing of joints complete as per direction of Engineer in

Concealed work including cutting chases and making good the walls etc.,

18.8.1 15mm nominal outer dia pipes METRE 20 497.80 9956.00

18.8.2 20mm nominal outer dia pipes METRE 20 537.60 10752.00

18.8.3 25mm nominal outer dia pipes METRE 5 627.25 3136.25

18.8.4 32mm nominal outer dia pipes METRE 5 739.30 3696.50

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards

19 and weighing not less than 690 gms.

18.51.1 15 mm nominal bore EACH 2 798.95 1597.90

Providing, fixing, jointing and testing in position of ISI marked UV stabilized UPVC pipes for soil,

waste, and vent, Type-B as per IS : 13592 suitable for rubber ring joints, including all neccessary

specials and fittings (confirming to IS:14735) i.e. bends, tees, junctions (with or without doors),

reducers, WC connectors, couplers, expansion joints / bellows, cowels, clamps, rubber rings, clean

outs etc. fixing at wall/ ceiling/ floor level supported by clamp & hangers etc. in concealed / inside

duct / under floor & basement ceiling / external work etc. including chase cutting as required,

excavation and back filling in all kind of soils, suspended from floor under false ceiling or embedding

20 the pipes laid under floors / building in 75 mm. alround 1:2:4 cement concrete (1 cement : 2 coarse

MR sand : 4 graded stone aggregate 20 mm nominal size) including cost of shuttering for proper

completion of the work, breaking and making good the walls and floors etc. after pipes have been

duly laid and tested. The rubber ring shall confirm to IS:5382.

The Pipes will be supported with threaded G I rods & U clamps with nuts, washers etc on 50x50x5

mm slotted angle. The cost will include all support arrangements. The work includes commissioning

of all pipes lines as per drawings and specifications and as directed by engg-in-charge at site.

a 110 mm dia (Wall Thickness - 3.2 to 3.8 mm) METRE 40 536.00 21440.00

b 75 mm dia (Wall Thickness - 3.2 to 3.8 mm) METRE 10 416.00 4160.00

Digitally signed by RAJ PAL

S NO DESCRIPTION UNIT QTY RATE

2023/ MR AMOUNT AMOUNT

Providing, fixing, jointing and testing in position ISI marked (IS:4985) UPVC pipes of min 6 Kg/

Sqcm rating with fitting for waste pipe from fixtures to floor trap including reduces, enlarger, socket,

MR 21 couplers, bends, tees etc including fixing at wall/ ceiling level supported by clamp & hangers etc.

cutting holes in wall/ floors/ slabs and making good the same with cement concrete 1:2:4 complete as

Providing & fixing UPVC Floor trap of self cleansing design with stainless steel grating complete in

MR 22 all respects.

Plain Floor Trap (4" Ht) with 50 / 75 outlet and with height raiser EACH 5 536.00 2680.00

MR 23 Extra for providing & fixing 125 mm dia C.P. grating in place of C.I. grating over floor traps. EACH 5 726.00 3630.00

Providing & fixing of SS Floor Cleanout, round or square with rubber seal and flat round cover with

screws and other required fitting complete as required.

Supply, Installation, testing and commisioning of toilet waste water super quiet portable pumping

station. Pump upto vertical 5 meters and horizontal 100 meter from toilet to vertical shaft with inlet

connection in portable pump side inlet of 50, 75, 110 as per requirement to complete the work as per

the directions of engineer in charge

Providing and fixing stainless steel tray below sewage pipe of size 200x200x200 mm of grade SS304

including all accessories

Supply, Installation, Testing and Commisiong of HIGH FLOW SINGLE LEVER CONCEALED

DIVERTOR FOR BATH & SHOWER

MR 28 Supply, Installation, Testing and Commisiong of SPOUT FOR BUILT IN BATH/SHOWER MIXER EACH 1 9377.00 9377.00

Supply, Installation, Testing and Commisiong of OVERHEAD SHOWER 350x350MM ROUND EDGE

MR 29 SQUARE HEAD SINGLE FLOW (BODY & FACE PLATE STAINLESS STEEL WITH CHROME EACH 1 24100.00 24100.00

PLATED) WITH RUBIT CLEANING SYSTEM

MR 30 Supply, Installation, Testing and Commissioning of 15 litre geyser EACH 2 12004.00 24008.00

MR 31 Supply, Installation, Testing and Commisiong of SOAP DISH HOLDER EACH 1 4392.00 4392.00

MR 32 Supply, Installation, Testing and Commisiong of TUMBLER HOLDER EACH 1 4309.00 4309.00

Supply, Installation, Testing and Commisiong of TOWEL RACK 600MM LONG WITH LOWER

MR 34 Supply, Installation, Testing and Commisiong of ROBE HOOK EACH 1 2045.00 2045.00

MR 35 Supply, Installation, Testing and Commisiong of TOILET ROLL HOLDER WITH COVER EACH 1 4978.00 4978.00

MR 36 Supply, Installation, Testing and Commisiong of TOWEL HOLDER EACH 1 3336.00 3336.00

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets

17.10 and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good

37 the walls wherever required :

17.10.1 Kitchen Sink with Drain Board

Supply, Installation, Testing and Commisiong of single lever sink mixer (table mounted) with

MR 38 extractable hand shower dual flow complete with 1.2 m long tube with 450 mm long braided hoses EACH 1 8131.00 8131.00

Digitally signed by RAJ PAL

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

S NO DSR 2022/ MR DESCRIPTION UNIT QUANTITY RATE DSR AMOUNT NDSR AMOUNT

A POINT WIRING

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface / recessed medium class PVC conduit,

A.1 with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS

PVC insulated copper conductor single core cable etc as required.

Wiring for group controlled (looped) light point/ fan point/call bell point (without independent switch

etc.) with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/ recessed

A.2 PVC conduit, and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single

core cable etc as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core

A.3 1.12 cable in surface/ recessed medium class PVC conduit alongwith 1 No 4 sq. mm FRLS PVC Metre 34920 334.00 11663280.00

insulated copper conductor single core cable for loop earthing as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box

including connections but excluding modular plate etc. as required.

1.24.4 3 pin 5/6 amp socket outlet Each 1133 122.00 138226.00

1.24.5 6 pin 15/16 amp socket outlet Each 85 197.00 16745.00

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding

A.5 1.26 modular plate as required. Each 200 40.00 8000.00

Supplying and fixing following size/module, GI box along with Modular base & cover plate on

existing modular metal boxes etc. as required.

B SUBMAIN AND CONTROL WIRING

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC insulated

copper conductor, single core cable in surface/ recessed medium class PVC conduit as required

B.1 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

1.14.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 50 439.00 21950.00

1.14.10 4 X 10 sq. mm + 2 X 6 sq. mm earth wire Metre 480 1005.00 482400.00

1.14.11 4 X 16 sq. mm + 2 X 6 sq. mm earth wire Metre 480 1365.00 655200.00

Digitally signed by RAJ PAL

S NO DSR 2022/ MR DESCRIPTION UNIT QUANTITY RATE DSR AMOUNT NDSR AMOUNT

Supplying and making end termination with brass compression gland and aluminium lugs for

9.1 following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV

grade as required.

Supply of following XPLE armourned 1.1 KV grade conforming to I.S.7098/1554Aluminium

Conductor Cables :

Supply of following sizes of PVC sheathed PVC/XLPE insulated Aluminium conductor armoured

cable of 1.1 KV grade conforming to IS:7098 part-1 / IS:1554 part-1 respectively & ISI marked.

(b) 3.5 C x 95 Sqmm XLPE cable RM 100 864.00 86400.00

(c ) 3.5 C x 70 Sqmm XLPE cable RM 100 680.00 68000.00

(d) 3.5 C x 50 Sqmm XLPE cable RM 100 510.00 51000.00

(e) 3.5 C x 35 Sqmm XLPE cable RM 100 378.00 37800.00

Supply of following sizes of copper cables -PVC sheathed PVC/XLPE insulated Copper conductor

C.3 MR armoured cable of 1.1 KV grade conforming to IS:7098 part-1 / IS:1554 part-1 respectively & ISI

(a) 4 C x 16 Sqmm XLPE copper cable RM 400 1446.00 578400.00

(b) 4 C x 25 Sqmm XLPE copper cable RM 100 2253.00 225300.00

(c ) 3.5 C x 35 Sqmm XLPE copper cable RM 50 2686.00 134300.00

(d) 3.5 C x 50 Sqmm XLPE copper cable RM 50 3224.00 161200.00

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker

2.10 suitable for inductive load of following poles in the existing MCB DB complete with connections,

testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete

with connections, testing and commissioning etc. as required.

Digitally signed by RAJ PAL

S NO DSR 2022/ MR DESCRIPTION UNIT QUANTITY RATE DSR AMOUNT NDSR AMOUNT

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB

distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus

bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But

D.4 without MCB/ RCCB/ Isolator)

MR 12 way (4 + 36), Double door Each 25 9081.00 227025.00

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual

2.14 current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing

MCB DB complete with connections, testing and commissioning etc. as required.

E PROVISIONS FOR VOICE, DATA, SECURITY & TV SYSTEMS

Supply, installation, testing & Commissioning of 1 module 16A SWITCH SP 1 way for floor box.

E.2 MR Supply, installation, testing & Commissioning of 2 module 16 A Socket for floor box box. Set 4 577.00 2308.00

Supply, installation, testing & Commissioning of Specific Backbox for Carpet for Floor Box along

E.3 MR with LID and TRIM for tiles/ marble 15 to 20mm thickness material for headband and single cable Set 2 12106.00 24212.00

outlet/ glavanized steel, paint RAL 7031 for floor box .

Supply, installation, testing & Commissioning of Specific Backbox for Wooden Flooring for Floor

E.4 MR Box along with LID and TRIM for tiles/ marble 15 to 20mm thickness material for headband and Set 2 6803.00 13606.00

single cable outlet/ glavanized steel, paint RAL 7031 for floor box.

Supply, installation, testing & Commissioning of flat support plate 8 module for integration of

Mechanism for Floor Box

Supply, installation, testing & Commissioning of waved support plates for 4 module (2x2) modules

E.6 MR for Floor Box Set 4 1533.00 6132.00

Supplying and fixing following modular switch / socket on the existing modular plate & switch box

1.24 including connections but excluding modular plate etc. as required.

1.24.7 TV socket outlet Set 38 148.00 5624.00

Supply, Installation, Testing and Commisioning of Galavanized Iron (GI) Raceways along with

MR required suitable number of GI couplers for joining raceways and fixing GI brackets and all

accessories complete in all respect as per the directions of engineer in charge

(a) 300mmx38mm(GI) - 3 compartment Mtr 500 3603.00 1801500.00

E.9 (b) 225mmx38mm(GI) - 3 compartment Mtr 200 2960.00 592000.00

Supply, Installation, Testing and Commisioning of Junction boxes for direct access to cables at the

intersection of raceways supplied completely with base and cover plates, height adjustable junction

box 65- 90 mm including all accessories ss plate of 3mm thick complete in all respect as per the

E.10 directions of engineer in charge

Digitally signed by RAJ PAL

S NO DSR 2022/ MR DESCRIPTION UNIT QUANTITY RATE DSR AMOUNT NDSR AMOUNT

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE

E.11 1.19 insulated, shielded with fine tinned copper braid and protected with PVC sheath in the exisitng Meter 1520 47.00 71440.00

surface/recessed steel/ PVC conduit as required

Supplying and fixing of following sizes medium class PVC conduit aong with accessories in

1.21 surface/ recess including cutting the wall and making good the same incase of recessed conduit

Supplying and Installation of following size perforated of painting with powder coating M.S. cable

trays of perforation of not more than 17.5% in convinient sections, joined with connectors

E.13 suspended from the cieling with MS suspenders including bolts and nuts painting suspenders etc

4.1.6 450 mm width x 50 mm depth x 2 mm thickness Metre 100 1137.00 113700.00

Supply, Installation, Testing and Commisioning of USB charger- 3000mA/15 Watts- Type C- 1

module complete in all respect

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and

F.1 5.6 providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 SET 10 13838.00 138380.00

metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as

F.4 5.16 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. MTR 2000 70.00 140000.00

G PANEL BOARDS

Designing, fabricating, transporting, unloading, storing, fixing in position, testing and

commissioning the following sheet steel cubicle type panels fabricated from 1.6mm thick CRCA

sheet, dust and vermin proof, outdoor type double door with canopy, TPN Panels with hinged

lockable doors fabricated from 2mm thick CRCA sheet, suitable for 415V, 3 phase 4 wire 50Hz AC

supply with rear access for cable alley and with segregated bus-bar chamber with tinned

aluminium bus bar and including supplying and fixing following switchgears, meters and

accessories, inter-connections, bonding to earth, powder coated painting and marking as

specified. Switch boards complete as per schematic diagram:

Type of construction: Form 3

IP classification: 42

The LT PANEL shall be electrically inter-locked as shown in Schematic diagram and as detailed in

the Specifications

Colour: Gray Powder Coated, as per approved sample.

1 nos, 250 Amps. 4 pole MCCB , i.e four pole Moulded Case Circuit Breaker of fault breaking

capacity 25 KA (ICS=ICU up to 433 V) complete in all respect

Digitally signed by RAJ PAL

S NO DSR 2022/ MR DESCRIPTION UNIT QUANTITY RATE DSR AMOUNT NDSR AMOUNT

TPN aluminum bus bars of minimum of 320 Amps capacity with heat shrinkable colored sleeves

and I/C DMC/SMC bus bars supports at required intervals complete for cross section, size

supports & their spacing etc. for withstanding fault level of 25 MVA for 1 Sec.

(a) 63 Amps, TPN, MCB - 6 Nos.

(b) 40 Amps, TPN, MCB - 4 nos

Panel complete as above Each 1 250000.00 250000.00

G.2 MR Floor Panels

Designing, fabricating, transporting, unloading, storing, fixing in position, testing and

commissioning the following sheet steel cubicle type panels fabricated from 1.6mm thick CRCA

sheet, dust and vermin proof, indoor type TPN Panels with hinged lockable doors fabricated from

2mm thick CRCA sheet, suitable for 415V, 3 phase 4 wire 50Hz AC supply with rear access for

cable alley and with segregated bus-bar chamber with tinned aluminium bus bar and including

supplying and fixing following switchgears, meters and accessories, inter-connections, bonding to

earth, powder coated painting and marking as specified. Switch boards complete as per schematic

Type of construction: Form 3

IP classification: 42

The LT PANEL shall be electrically inter-locked as shown in Schematic diagram and as detailed in

the Specifications

Colour: Gray Powder Coated, as per approved sample.

1 nos, 250 Amps. 4 pole MCCB , i.e four pole Moulded Case Circuit Breaker of fault breaking

capacity 25 KA (ICS=ICU up to 433 V) complete in all respect

TPN aluminum bus bars of minimum of 320 Amps capacity with heat shrinkable colored sleeves

and I/C DMC/SMC bus bars supports at required intervals complete for cross section, size

supports & their spacing etc. for withstanding fault level of 25 MVA for 1 Sec.

(a) 63 Amps, TPN, MCB - 4 Nos.

(b) 40 Amps, TPN, MCB - 10 nos

Panel complete as above Each 2 250000.00 500000.00

G.3 MR UPS Output Panel

Designing, fabricating, transporting, unloading, storing, fixing in position, testing and

commissioning the following sheet steel cubicle type panels fabricated from 1.6mm thick CRCA

sheet, dust and vermin proof, indoor type TPN Panels with hinged lockable doors fabricated from

2mm thick CRCA sheet, suitable for 415V, 3 phase 4 wire 50Hz AC supply with rear access for

cable alley and with segregated bus-bar chamber with tinned aluminium bus bar and including

supplying and fixing following switchgears, meters and accessories, inter-connections, bonding to

earth, powder coated painting and marking as specified. Switch boards complete as per schematic

Type of construction: Form 3

IP classification: 42

Digitally signed by RAJ PAL

S NO DSR 2022/ MR DESCRIPTION UNIT QUANTITY RATE DSR AMOUNT NDSR AMOUNT

The LT PANEL shall be electrically inter-locked as shown in Schematic diagram and as detailed in

the Specifications

Colour: Gray Powder Coated, as per approved sample.

One (1) nos, 200 Amps. 4 pole MCCB , i.e four pole Moulded Case Circuit Breaker of fault

breaking capacity 25 KA (ICS=ICU up to 433 V) complete in all respect

TPN aluminum bus bars of minimum of 320 Amps capacity with heat shrinkable colored sleeves

and I/C DMC/SMC bus bars supports at required intervals complete for cross section, size

supports & their spacing etc. for withstanding fault level of 25 MVA for 1 Sec.

(a) 63 Amps, TPN, MCB - 4 nos

(b ) 40 Amps, TPN MCB - 10 nos

Panel complete as above Each 1 314297.00 314297.00

H SAFETY ITEMS

Providing and fixing MV danger notice plate of 200mm x 150mm made of mild steel, atleast 2 mm

H.1 2.21 thick, and vitreos enamelled white on both sides and with iscription in single red colour on front Nos. 6 269.00 1614.00

side as required

Supply, Installation, Testing and Commissiong of Hot-swappable Modular Type 75 KVA/KW (3 no

25 kva module + 1 no of 25 kva redundant module)True Online Double Conversion UPS 3Phase

Input - 3Phase Output UPS having Decantralized Architecture. Module size should be 25 kVA with

multi controller. IGBT Based Rectifier and IGBT Based Inverter Batteries:12 V, SMF

I.1 Amararaja/Exide with minimum VAH capacity of 60000 suitable for 30 minutes backup with each Nos. 1 3166017.00 3166017.00

ups Along with Accessories Rack, Interlinks, SFU, DC Cable Upto 5 Meters complete in all respect

as per the directions of the engineer in charge. UPS should have availability of Input /Output

isolator, Inbuilt manual bypass along with phase sequence corrector. UPS Efficiency shall not be

Total of Electrical items 19432533.00 11617163.00

Digitally signed by RAJ PAL

SCHEDULE OF QUANTITIES - HVAC WORKS

DSR HVAC TOTAL

S No 2019/DSR DESCRIPTION UNIT QUANTITY RATE AMOUNT

EM 2018 DSR (INR) NON-DSR (INR)

Supply Installation, Testing & Commissioning of modular type Variable Refrigerant Flow/Variable

Refrigerant Volume air cooled Outdoor units suitable for cooling and heating, having all

hermetically sealed inverter type Scroll Compressor(s), minimum two compressors for above 14

HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R 410

A Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The unit shall

deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without

tripping. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply. The

unit shall be filled with first charge of the refrigerant and ready for use as required. The COP at

AHRI conditions shall not be less than 3.1 and IEER not less than 6.5 .

2 2 Supply, installation, testing and commissioning of following minimum capacity 4-way flow

2.1 2.4 VRV/VRF

1.6 TR Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre- Each 6 30204.00 181224.00

Supply, installation, testing and commissioning of following minimum capacity VRV/VRF High wall

type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise

fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic

expansion valve, outer cabinet, cord less remote control, drain pan, necessary accessories etc.,

suitable for operation on 230 V ± 10%, 50 Hz, single phase AC supply, complete as required. The

unit shall have automatic force shut down provision in case of fire on receiving signal from BMS

System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19

Degree C WB temperature.

Lifting, Shifting, Supply, Installation, Testing & Commissioning of Interconnecting "Y" & "T" Joints

i.e. Refnet Joints/ Header with Insulation for refrigearnt piping

Refrigerant Piping

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of

following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete

5 5 with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including

accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric

nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid

lines, all accessories as per specifications etc. as required :

5.1 5.1 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 240 245.00 58800.00

Digitally signed by RAJ PAL

DSR HVAC TOTAL

S No 2019/DSR DESCRIPTION UNIT QUANTITY RATE AMOUNT

EM 2018 DSR (INR) NON-DSR (INR)

5.2 5.2 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 800 331.00 264800.00

5.3 5.3 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 240 466.00 111840.00

5.4 5.4 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 800 588.00 470400.00

5.5 5.5 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 150 707.00 106050.00

5.6 5.6 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 150 865.00 129750.00

5.7 5.7 25.4 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 50 1022.00 51100.00

5.8 5.8 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 50 1108.00 55400.00

6 1.14 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC

insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as

Supply, installation, testing and commissioning of PVC drain water with necessary clamps, fittings

such as bends tees etc. and duly insulated.

40 mm dia (9mm thick insulation) Rm 1300 374.00 486200.00

Total HVAC-VRV WORKS 3872830.00 756474.00

Digitally signed by RAJ PAL

SCHEDULE OF QUANTITIES - HVAC WORKS

DSR (E & M- Non DSR

S NO DESCRIPTION UNIT QUANTITY RATE DSR AMOUNT

2022)/ MR AMOUNT

VAV BOX (WITH INTEGRAL SOUND ATTENUATOR)

Supply and Installation of pressure independent rectangular VAV unit with integral sound attenuator made

of 22G GI sheet casing length 900mm consisting of 25mm thick 48kg/m3 density fiber glass wool covered

with tissue paper ,elliptical volume control damper , calibrated differential pressure sensor (DPT sensors)

at inlet complete with digital Thermostat.(All VAV shall be factory calibrated).

Supply, installation, testing and commissioning of Variable Frequency Drive (VFD) 380-400 VAC, IP-54

MR Chassis, RFI class A1 (C2), No brake chopper.

a VFD upto 35 HP or as directed by the engineer in charge Nos. 2 180000.00 360000.00

DUCT PRESSURE SENSORS

Supply, Installation and Testing of pressure sensors to be installed in supply air ducts. Quoted price

3.0 MR shall be inclusive of necessary conduting, copper control cabling from the sensors to the respective VFDs Nos. 8 17500.00 140000.00

as per "Approved Shop Drawings".

Supply, Installation, Testing & Commissioning of Silent type circular /rectangular inline fans for exhaust air

complete with sheet metal casing, 25mm thick acoustic insulation, direct driven centrifugal fan, motor with

proper protection and inspection door. Fan shall be suitable for operation on 220+6 % volts, 50 Hz,1

phase AC power supply. Flanges to be provided on both sides to facilitate duct connections. Fan shall be

installed as shown in the drawings and will be of following characteristics:

All single phase inline fans shall be provided with factory fitted speed regulators. All Fans Should be

complete with Plug Top & necessary power cable.

Fans shall have low noise level in rage of 35-40dBA @3m and shall be suitable for indoor installations.

a 200 CFM S P of 13-14 for Toilet Nos. 1 6449.00 6449.00

b 500 CFM S P of 13-14 for Kitchen Nos. 1 9500.00 9500.00

5.0 Tube Axial Fan

Supply Installation, testing and commissioning of supply air Tube Axial flow fan of following capacity with

GSS casing and aluminium alloy impellers with high efficiency aero-foil sections, blades, the impeller

directly driven by TEFC induction motor suitable for 3 Phase 50 Hz 415 V ± 10 %, complete as required.

This cost shall include the cost for suitable panel, DOL starter, breakers etc compete in all respect as per

the directions of engineer in charge.

9000 cfm at 15 mm static presuure for fresh air/exhaust air With Class "H" insulation. NOS 6 143910.00 863460.00

Supplying, Fixing, testing and commissioning of fire dampers in supply air duct/main branch and return air

path as and where required of required sizes i/c control wiring,the damper shall be motorized and spring

return so as to close the damper in the event of power failure automatically and open the same in case of

6.0 16.20 power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The

damper shall also be closed in the event of fire signal complete as required and as per specifications.

(Fire damper shall ve suitable for 120 minutes fore rating as per NBC norms)

Digitally signed by RAJ PAL

GI Gravity Louver

7.0 MR Supply, installation, testing and commissioning of GI Gravity Louver complete with neoperene rubber

gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications.

8.0 VOLUME CONTROL DAMPER

MR Supply, Installation and Testing of GI box type volume control dampers as per the specifications and shop

a drawings. SQM 15 5900.00 88500.00

- For Rectangular Ducts

Supply, Installation, Testing and Commisioning of powder coated GI sheet metal factory fabricated flat oval

ducting with fittings and gripple wire supports. The factor of gripple support to suit the duct weight with

necessary anchor fastners and hook arrangements with suitable thickness etc., confirming to SMACNA

9.0 MR standards. Duct should be fabricated by using CNC machines including neccesary civil works as per site

condition. The joints shall be seamless and ducts joining shall be done using rivets only. The ducts shall be

powder coated with RAL color as per architect approval. The complete ducting cost shall be including 9

mm thick nitrile rubber thermal with insulation internally. The insulation used for factory lining shall be of

self adhesive type.

a MR Thickness 0.63 mm sheet SQM 800 1721.00 1376800.00

b MR Thickness 0.80 mm sheet SQM 500 2023.00 1011500.00

c MR Thickness 1.00 mm sheet SQM 200 2340.00 468000.00

d MR Thickness 1.25 mm sheet SQM 100 2900.00 290000.00

Diffusers & Grills

Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume control

dampers as per specifications.

Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume

control dampers complete as required

Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminium with aluminium

volume control dampers with anti smudge ring & removable core.

Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminium without volume

control dampers with anti smudge ring & removable core.

Supply, Installation, Testing of 125mm deep antivibration flexible joints at the outlet of air handling

14.0 MR units/ductable split units//inline fans. Flexible connections shall be constructed using imported fire retardant RM 100 1440.00 144000.00

fabric with extruded aluminium frame/flange on both sides of approved make.

Supply, Installation, Testing and Balancing of linear slot diffusers as per the approved shop drawings and

specifications. Each slot shall be 25mm wide. The diffuser face shall be a one piece extrusion so there are

no visible joints. Slot diffusers shall be complete with end caps either as end plates or end angles or

integral part, air control blades etc. Slot diffuser have a variable neck length and the diffuser face could be

15.0 MR optionally be fitted to the plenum box on site. Diffuser shall have provision to access collar dampers for air

All Return air diffusers in false ceiling to be properly supported from real slab using chains or gripple wires.

3 slot/2slot, powder coated extruded aluminium diffusers of approved colour & shade. SQM 10 12500.00 125000.00

Digitally signed by RAJ PAL

Supply, Installation and Testing of Bird Screens with GI wire mesh to be installed at the suction of fresh

16.0 MR air/discharge of Exhaust air as per the specifications and shop drawings. Sample of bird screen to be got SQM 10 5436.00 54360.00

approved from consultants and Clients prior to procurement.

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile

rubber (Class "O") insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints

17.0 shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as

per specifications and as required.

Supply and fixing of acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool

having density of 32 kg/m³, with 25 mm X 25 mm GI section of 1.25 mm thick, at 600 mm centre to centre

18.0 16.21 covered with Reinforced Plastic tissue paper and 0.5 mm thick perforated aluminum sheet fixed to inside SQM 10 708.00 7080.00

surface of ducts with cadmium plated nuts, bolts, stick pins, CPRX compound etc. complete as required

and as per specifications

The Active Air Purification system should consist of Supply, Installation, Testing and commissioning of

Bipolar Ionisation System. The Bipolar Ionisation System shall be of Needle Point Model (Needle Point)

should have Nitinol (nickel titanium) Needles and Carbon Fibre Brush Model, System should produce

positive and negative ions for creating a Bio Climate rich in ions and hence neutralising harmful pollutants

including pathogens, Volatile Organic Compounds and Particulate Matter within the occupied space.The

ionizer shall be installed at the fan inlet of fan coil units, VRF cassettes, ductless splits, AHU and Ductable

HVAC System. The Unit should accept 12-24 VAC/DC. Product should have UL 867 and UL 2998

certification (for zero ozone emission), UL 2043 (for Fire and Smoke Safety), ISO 16000, CSA C22.2# 187

on atleast any one product. The OEM shall have Efficacy test report on SARS-CoV-2 OMICRON VARIANT

and from any Internationally/Nationally recognised Laboratory.

Smart Indoor Air quality monitor to measure Air quality parameters including AQI, PM1, PM2.5, PM10,

CO2, Humidity and Temperature. In addition to the mentioned sensors of the base device, you can

customize it to measure more parameters by adding extra sensors. This monitor should be a 3-tier

architecture including sensor Hardware, secure cloud infrastructure, monitoring apps including dashboard,

20.0 MR android/IOS apps, where ever requires. Dashboard should be customisable and IOT (Internet of things)

enabled with view and management for all of your locations on one dashboard so that you can easily

identify and address any air quality issues. Sensors should be soft calibratable. The System should be

capable of providing periodic Preventive maintenance for automated after sales support service in form of

notification/ alerts and user interaction through dashboard application.

Air Quality Monitor Nos 6 75796.00 454776.00

Digitally signed by RAJ PAL

Supply, installation testing and commissioning of Router / Supervisory Controller which will manage the

VAV information and communicates on BACnet®/ LONWORKS® protocol to monitor and Control the

VAVs from BMS software on PC in accordance with the approved shop drawings and technical

specifications. Connecting the final daisy loop from all VAV to Supervisory Controller shall be part of the

scope. The communication between Supervisory controller and BMS software in PC should be on IP. Cost

include powder coated Panel for Supervisory Controller of required size with 24 Volts provision which

includes power cable, plug, transformer and with all necessary accessories for mounting on wall in

accordance with the approved shop drawings and technical specifications.

Supply, Laying, Termination of ISI Certified 2 Core 1.0 sq.mm ATSC, FRLS,PVC insulated, Unarmored,

Tinned Copper, twisted, shielded, PE insulated, VAV Communication Cable with proper ferrules, lugs and

other necessary accessories. The spec shall meet the system manufacturer specifications.

Supply, Laying, Termination of ISI Certified 4 Core 1.0 sq.mm ATSC, FRLS ,PVC insulated, Unarmored,

23.0 MR Tinned Copper, twisted, shielded, PE insulated, VAV Communication Cable with proper ferrules, lugs and Rmt 400 280.00 112000.00

other necessary accessories. The spec shall meet the system manufacturer specifications.

Supply & Laying of ISI Certified 1" dia PVC Conduit with bends, collar, saddles, saddle base and other

accessories for Signal Cable / DDC Communication Cable

TOTAL HVAC WORKS 1381944.00 9242957.00

Digitally signed by RAJ PAL

SCHEDULE OF QUANTITIES: LIGHTING

S No Item Description Product Image Unit Quantity Rate DSR Amount NDSR Amount

Supply, Installation, Testing and Commissioning of Recess type 6W non-dimmable LED downlighter neutral

white (4000 K) with LED having pressure die cast aluminium hang body having high efficiency diffuser with

more than 85% transmittance with rated life of L-70 @50000 hrs having system lumen output better than 750

lumens,with efficacy better than 125 lumen/ watt with CRI>90 & Driver efficiency> 90% (Driver complaince

IEC 62384,IEC 61547,IEC 61347-2-13,EMICISPR15, THD<10%,PF>0.95 ) etc. with inbuilt protection against

1 short circuit,Miswiring,over voltage and surge protection upto 3 KV including making suitable arrangement for Nos 200 4087.00 817,400.00

fixing complete as required complete as reqd.

Supply, Installation, Testing and Commissioning of Recess type 15W non-dimmable LED downlighter neutral

white (4000 K) with LED having pressure die cast aluminium hang body having high efficiency diffuser with

more than 85% transmittance with rated life of L-70 @50000 hrs having system lumen output better than

1875 lumens,with efficacy better than 125 lumen/ watt with CRI>90 & Driver efficiency> 90% (Driver

complaince IEC 62384,IEC 61547,IEC 61347-2-13,EMICISPR15, THD<10%,PF>0.95 ) etc. with inbuilt

2 protection against short circuit,Miswiring,over voltage and surge protection upto 3 KV including making Nos 85 5749.00 488,665.00

suitable arrangement for fixing complete as required complete as reqd.

Supply, Installation, Testing and Commissioning of Surface type 15W non-dimmable LED downlighter neutral

white (4000 K) with LED having pressure die cast aluminium hang body having high efficiency diffuser with

more than 85% transmittance with rated life of L-70 @50000 hrs having system lumen output better than

1875 lumens,with efficacy better than 125 lumen/ watt with CRI>90 & Driver efficiency> 90% (Driver

complaince IEC 62384,IEC 61547,IEC 61347-2-13,EMICISPR15, THD<10%,PF>0.95 ) etc. with inbuilt

3 protection against short circuit,Miswiring,over voltage and surge protection upto 3 KV including making Nos 178 5561.00 989,858.00

suitable arrangement for fixing complete as required complete as reqd.

Supply, Installation, Testing and Commissioning of non-dimmable Suspended /surface 36W LED linear

light(1200mm) Linear ultra modular fixture made up of extruded aluminium housing and multi LED anti glare

system having system lumen >3900 with luminaire efficacy 130LPW , CRI >90, UGR<19 CCT 4000K. The

luminaire rated life (L70) 50000 hours with inbuilt protection against short circuit,Miswiring,over voltage and

surge protection upto 3 KV PF.0.95 and THD<10% (Driver complaince IEC 62384,IEC

61547,IEC 61347-2-13)including making suitable arrangement for fixing including connection with 3 x 1.5

sq.mm. PVC insulated FRLS PVC sheathed copper conductor etc as required.

Digitally signed by RAJ PAL

S No Item Description Product Image Unit Quantity Rate DSR Amount NDSR Amount

Supply, Installation, Testing and Commissioning of non-dimmable Suspended /surface 36W LED linear

light(1200mm) Linear ultra modular fixture for making continous linear arrangement including cascading kit

etc made up of extruded aluminium housing having high efficiency diffuser with more than 85% transmittance,

system lumen >3900 with luminaire efficacy 130LPW , CRI >90 ,UGR<19 CCT 4000K. The luminaire rated

life (L70) 50000 hours with inbuilt protection against short circuit,Miswiring,over voltage and surge protection

5 upto 3 KV PF.0.95 and THD<10% (Driver complaince IEC 62384,IEC 61547,IEC 61347-2-13)including MTR. 290 8308.00 2,409,320.00

making suitable arrangement for fixing including connection with 3 x 1.5 sq.mm. PVC insulated FRLS PVC

sheathed copper conductor etc as required.

Supply, Installation, Testing and Commissioning of recess type 36W non-dimmable LED (direct/indirect) of

295 x 1195 mm size with aesthetically designed extruded aluminium housing & injection molded PC

component diffuser with efficacy better than 110 Lumen/watt (minimum total lumen delivered package 3900),

with CCT=4000K, CRI>90, PF>0.95,THD<10% & with Driver having efficiency >85% .Service life of 50,000

hrs @ L 70 etc complete as required.

Supply, Installation, Testing and Commissioning of 20W/M LED flexible strip made of 240 LED / meter and

Flexible FR4 PCB with copper contacts. CCT = 4000K, CRI >90. With aluminium extrusion casing.

Supply, Installation, Testing and Commissioning of 150W non-dimmable Constant voltage power supply with

24VDC output and 220VAC input, PF> 0.95, THD < 10%, 6KV Surge protection, Sorchit Circuit Protection,

Open Circuit protection, over load protection including connection with 3 x 1.5 sq.mm. PVC insulated FRLS

PVC sheathed copper conductor etc as required.

Supply, Installation, Testing and Commissioning of STRETCHED FABRIC CEILING: Supply & installation of

fabric false ceiling / wall formed out with TRANSLUCENT Printed fabric coverings made out of

polyester knitted fabric coated with Polyurethane (PU). The TRANSLUCENT Printed fabric width of 2m, 3m,

4.1m &5.1m with weight of 200gm/m2, thickness of 0, 3 mm. The appearance of fabric is matt, smooth and

uniform with blanq color and light transmission of 50%. The tear strength of fabric should be accordance to

CH: 4,5daN; TR: 6,5 daN. The fire rating should be accordance to B-S1, d0. The fabric should be

humidity resistant and free of carcinogenic substances(CMR) or volatile organic Compounds (VOC’s). At

9 labeling in accordance with the French decree no. 2011- 321, Oeko-Tex standard100 certified. Fabric MTR. 55 13199.00 725,945.00

should be installed with approved manufacturer guidelines. It comes with 10- year manufacturer

guarantee. The installation of TRANSLUCENT Printed fabric should be dry installation & done at room

temperature using CLIPSO PVC, ABS Grippers. Clipso ceiling base to be made of MS or Wooden frame

finishing to a flush finish of tapered and square edges in desired design as per architect specification.Supply

of LED Lights behind the Fabric Wall/ False ceiling in modules/ PCB with recommended wattage as per

manufacturer's standards to give an effect of ambient lighting. LED make MLS/ Bridgelux / Osram- SMD

2835, LED spacing / Pitch should be atleast 73 -80mm with beam angle of 170 degree, Colour temperature

shoud be as per design intent 3000K/4000K/6000K. Wattage of 8- 10W/mtr. LED modules/ PCB should

Supply, Installation, Testing and Commissioning of recessed trimless track with 4 wire / conductors suitable

for mounting of non-dimmable lights, made of extruded aluminium powder coated in black colour. It should

come with suitable accesries such as mounting clips, end caps etc and front cover.

Digitally signed by RAJ PAL

S No Item Description Product Image Unit Quantity Rate DSR Amount NDSR Amount

Supply, Installation, Testing and Commissioning of non-dimmable track mounted 18W LED linear light

(22mm wide) which is installed magnetically to the track, Linear ultra modular fixture made up of extruded

aluminium housing and multi LED anti glare system having system lumen >2340 with luminaire efficacy

11 130LPW , CRI >90, UGR<19 CCT 4000K. The luminaire rated life (L70) 50000 hours with inbuilt protection Nos 96 7370.00 707,520.00

against short circuit,Miswiring,over voltage and DC-DC 48VDC input Driver (Driver complaince IEC

Supply, Installation, Testing and Commissioning of Recessed / Surface mountedPIR based Human Body

Infrared Detector is a high-performance motion sensor designed for seamless integration into residential,

commercial, and industrial spaces. Operating on AC220V, it features a detection range of 6–8 meters with a

120° angle, making it ideal for efficient lighting control or security systems. The embedded design ensures a

12 sleek installation in walls or ceilings, maintaining aesthetic appeal while providing reliable functionality. Nos 120 3283.00 393,960.00

This device uses advanced infrared technology to detect human movement with high sensitivity and

adjustable timing settings ranging from 10 seconds to 7 minutes. Its compact size ensures easy installation,

while its durable ABS material offers long-term reliability. The sensor supports a maximum load 200W LED or

fluorescent lights, making it suitable for various applications.

Digitally signed by RAJ PAL

SCHEDULE OF QUANTITIES: IT

S No Description UNIT QUANTITY RATE DSR AMOUNT NDSR AMOUNT

A. UTP Components for Data

Supply, Fixing & Laying of CAT 6A UTP cable 23 AWG solid copper conductors

1 for Connectivity of Hub room to End Point.High Speed Gigabit Ethernet U/UTP, 250 MHz, Mtr 51825 48.00 2,487,600.00

Class E, 23 AWG, Unshielded Cable, C6

Supply, Installation, Testing and Comissioning of I/O port for CAT6A cable termination at

Work Station end. Keystone Unshielded Outlet, 180DG C6

Supply, Installtion, Testing and Commissioning of CAT6A patch cord 2 Mtr (7 feet) for

3 information outlet (I/O) to end user device connectivity. High Speed Gigabit 24AWG U/UTP Nos. 386 240.00 92,640.00

Supply, Installation, Testing and Comissioning of CAT6A patch cord 1 Mtr (3 feet) for

4 information outlet (I/O) to Rack End Redantant device connectivity. High Speed Gigabit 24AWG Nos. 386 191.00 73,726.00

U/UTP Patch Cord, C6

Supply, Installation, Testing and Comissioning of 24 port Loaded Jack Panel for CAT6A cable

termination at rack end. Data Active

Supply, Fixing & Laying of High-Speed Gigabit Ethernet UTP 250 MHz Class E Cables for

Category 6 Consists of 23AWG Solid Bare Electrolytic Grade Copper Conductors, HDPE

Insulated Twisted 4 Pair, RipCord, and LSZH Outer Jacket. These structured cables are suitable

for Gigabit Ethernet (1000 Base-T) requirements for applications such as High-Speed Data,

Voice & Video Signals over LANs, Server Farms, and Other Bandwidth Sensitive Indoor

Supply , Installtion , Testing and Comissioning of Category 6 UTP RJ45 keystone jacks

conform to class E performance. The Press-Fit technology is able to complete the insertion of the

IDC and RJ-45 contacts into a PTH (Plated-Through Hole) on a PCB (Printed Circuit Board). The

connection is established without using solder. Press-Fit technology connections avoid quality

problems such as cold Spots, voids, splatters, and cracks, and it is highly reliable than soldering.

Press-Fit technology does not use solder, it uses no lead (Pb) and there is no extra heat on the

connections. It makes the connections clean, reliable, and meets RoHS standards.

Supply , Installtion , Testing and Comissioning of 24 port Loaded Staggered Jack Panel

for CAT6 cable termination at rack end. Voice Active

Supply , Installtion , Testing and Comissioning of Category 6 UTP 2 Mtr Patch cords are

manufactured using high quality un-shielded 4 Pair Stranded cables, and features cable strain

relief boot with plug latch protection cap. These high-performance components are available in a

broad range of lengths. They are designed to meet or exceed Cat6 specifications. Conductors

are securely mated with an unshielded RJ45 plug design to deliver superior performance.

Supply, Installation, Testing and Comissioning of 2 Port British Style Shuttered Face

Plate white for I/O fixing at user side

Supply, Installation, Testing and Comissioning of 4 Port British Style Shuttered Face

Plate white for I/O fixing at user side

Supply, Installation, Testing and Comissioning of 24 port Loaded Staggred Jack Panel for

CAT6 cable termination at rack end. Riser Active

Supply, Installation, Testing and Comissioning of 400 pair MDF box complete with Krone

14 Supply, Installtion, Testing and Comissioning of 50 pair riser cable Mtr 400 262.00 104,800.00

C. Network Rack and Other Accessories

Digitally signed by RAJ PAL

SITC of 42U 800x1000 Server Rack with perforation, Glass Door, Cable managemenet, 6/16A

power strips-2 nos, Castors, 4 fan for cooling, Rack should have shelves - 4 nos

Digitally signed by RAJ PAL

SITC of L3 Switch with 24-port 10G/1G SFP28 with modular uplinks ,24 ports - L3 - managed -

stackable,Rack-mountable 1U,Switching capacity: 2000 Gbps ¦ Switching capacity with stacking:

3000 Gbps ¦ Forwarding rate: 1488 Mpps ¦ Forwarding rate with stacking: 2232 Mpps,IPv4

routing table entries: 39000 ¦ Flexible NetFlow entries: 128000 ¦ Direct IPv4 routes: 24000 ¦

Indirect IPv4 routes: 15000 ¦ IPv6 routing table entries: 19500 ¦ VLAN IDs: 4094 ¦ Switched virtual

interfaces (SVIs): 1000 ¦ Multicast routing flow table: 8000 ¦ QoS scale entries: 4000 ¦ ACL scale

16 entries: 5000 ¦ PVST instances: 300 ¦ STP Virtual Ports for PVST: 13000 ¦ STP Virtual Ports for Nos. 2 971,423.00 1,942,846.00

MST: 13000 ¦ Routed ports: 448,OSPF, IS-IS, RIP-1, RIP-2, IGMP, VRRP, PIM-SM, OSPFv3,

PIM-SSM, policy-based routing (PBR), RIPng,SNMP 1, RMON 1, RMON 2, SNMP 3, SNMP 2c,

CLI, NETCONF, RESTCONF,IEEE 802.3, IEEE 802.3u, IEEE 802.1D, IEEE 802.1Q, IEEE

802.3ab, IEEE 802.1p, IEEE 802.3af, IEEE 802.3x, IEEE 802.3ad (LACP), IEEE 802.1w, IEEE

802.1x, IEEE 802.1s, IEEE 802.3at, RAM 16 GB,Flash Memory 16 GB, Expansion Slots 1 (total)

/ 1 (free) x expansion slot

SITC of Access Switch with minimum of 48-port Data Switch, 48x10/100/1000 copper ports,

Software Network Essentials, Virtual Networks 4, Stacking bandwidth 160GBPS, Total number of

MAC addresses 3200, Total number of IPv4 routes (ARP plus learned routes) 14,000 (10,000

direct routes and 4,000 indirect routes), IPv4 routing entries 4000, IPv6 routing entries 2000,

Multicast routing scale 1000, DRAM 4GB, Flash 4GB, Switching capacity 176GBPS, Forwarding

SITC of Hardware controller managed Indoor Wi-Fi 6 (802.11ax) Access Point, 4x4 MIMO with

four spatial streams, 2.4 GHz, peak gain 3 dBi, internal antenna, omnidirectional in azimuth, 5

18 GHz, peak gain 4 dBi, internal antenna, omnidirectional in azimuth, 1x 100, 1000, 2500 Nos. 27 31,875.00 860,625.00

Multigigabit Ethernet (RJ-45) – IEEE 802.3bz, Management console port (RJ-45), USB 2.0, 2048

MB DRAM, 1024 MB flash

SITC of Access Switch with minimum of 48-port POE Data Switch, 48x10/100/1000 PoE

ports,Software Network Essentials,Virtual Networks 4,Stacking bandwidth 160GBPS,Total

number of MAC addresses 3200,Total number of IPv4 routes (ARP plus learned routes) 14,000

(10,000 direct routes and 4,000 indirect routes),IPv4 routing entries 4000,IPv6 routing entries

2000,Multicast routing scale 1000,DRAM 4GB,Flash 4GB,Switching capacity

176GBPS,Forwarding rate 261.9GBPS

20 SITC of 10 Gig SR transceivers/equivalent LC connector MM Nos. 44 19,638.09 864,076.00

SITC of Wireless Controller with IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX

specification, 1000BASE-T, 1000BASE-SX, 1000-BASE-LH, IEEE 802.1Q VLAN tagging, IEEE

802.1AX Link Aggregation, Web-based: HTTP/HTTPS, Command-line interface: Telnet, Secure

Shell (SSH) Protocol, serial port

22 SITC of Fiber Patch Cords 24 2,500.00 60,000.00

Digitally signed by RAJ PAL

Schedule of Quantities: EPBAX

S No Description UOM Qty Rate DSR Amount NDSR Amount

Supply, Installation, Testing & Commissioning of EPBAX with 2 PRI and 300 analog

extension expandable till 500 extensions capable of being PCM/TDM with voice mail,

auto apending , call forwarding etc facilities with operator console complete in all

respect as per the directions of engineer in charge

2 Analog Phone with Speaker 288 1,508.00 434,304.00

Digitally signed by RAJ PAL

Schedule of Quantities: IP BASED CCTV SYSTEM

S No Description Unit Qty Rate DSR Amount NDSR Amount

SITC of 5MP IR Vandal Proof Dome Network Camera Lens Size: 3.0mm – 13.5mm motorized vari-focal lens, Aperture

F1.4 – F3.2, NDAA Compliance must approved, Security: SSL Encryption, Multi-User Authority, IEEE802.1x, IP

Filtering, HTTPS , IR Distance : 30M IR, Memory Support : Micro SD 512 GB, Two-way Audio Communication

supported, Audio Compression Algorithm: ADPCM 16K, G.726, G.711 u-Law, G.711 a-Law DC12V/PoE, IP67 and K10

rating, Image Sensor: 1/2.8” CMOS Maximum Resolution: 2592 x 1944, 11, Video Resolution: 4:3 : 2592x1944,

H.264, Dynamic Range: 120dB, True Day & Night: Yes (ICR) MJPEG Scanning Mode: Progressive Scan COLOR : 0.15

lux @ F2.0 B/W : 0 lux (IR LED ON), Shutter Speed (Auto) 1/10000s~1s, True day/night, WDR 120db, 3D DNR, HLC &

1 BLC, Quadruple streams, Four Streams individually configurable, Privacy Masking: 8 Zone, Camera shall confirm Nos. 32 49,950.00 1,598,400.00

ONVIF Profile S, Smart codec by ROI, MTBF time 1,25,000 Hours @40 degree (Report to be submitted), Inbuilt

Analytics Motion Detection, Alarm in, Tampering and Trip Zone, Shall provide Quadruple streams, Object , SSL

Encryption, Multi-User Authority, IEEE 802.1x, IP Filtering, HTTPS , Operating Temperature: -40°C ~ +55°C (-40°F ~

+131°F) , Operating Humidity: 0% to 90% non-condensing, Certification: BIS/UL, FCC, CE approval. MAC Address: The

MAC address of the proposed IP cameras must be registered in the same name of the OEM. The IP Camera OEM must

confirm that the MAC address of the surveillance cameras; OUI must be in the name of the OEM. etc complete as per

specifications of this and directions of Engineer-in- Charge

Supply, Installation, Testing & Commissioning of 32 Channel IP network video recording capability Rack mount NVR

with Redundant Power Supply and minimum 8 Slots, should support H.264/H.265 compression, network incoming

throughput of 850 Mbps and 12MP recording resolution, time division multiplexing, real time recording of multiple

cameras, storing digitized and compressed images on internal hard disk drives for fast search and retrieval either locally

2 at the unit, or from a remote workstation using a Graphical User Interface (GUI), should allow all connected cameras to Nos. 1 375,529.00 375,529.00

be discovered and configured automatically, simultaneous live view, record, play back, data transmission in real time,

maximum throughput of 400 Mbps, UHD 1920 ips, support H.264/H.265 compression, 2X – 12X digital zoom in live

view mode, 2X – 12X digital zoom in playback mode, time lapse, event, time lapse + event, pre / post-event, panic

recording schedule, recording bitrate control mode: CBR and VBR, alarm, audio, motion, trip zone, video loss, text-in,

Supply Installation Testing & Commissioning of 43 inch Full HD LED monitor including wall mount brackets/ clamps/

desk mounting stand.

4 Supply and fixing of RJ45 Connector Nos. 34 20.00 680.00

Supply, Installation, Testing and Comissioning of I/O port for CAT6A cable termination at Work Station end.

Keystone Unshielded Outlet, 180DG C6

Supply, Installation, Testing and Comissioning of 1 Port British Style Shuttered Face Plate white for I/O fixing at user

Supply, Fixing & Laying of CAT 6A UTP cable 23 AWG solid copper conductors for Connectivity of

7 Hub room to End Point.High Speed Gigabit Ethernet U/UTP, 250 MHz, Class E, 23 AWG, Unshielded LSZH Cable, RM 2550 50.00 127,500.00

Supply, Installation, Testing and Comissioning of 24 port Loaded Jack Panel for CAT6A cable termination at rack end.

Supply, Installation, Testing and Comissioning of CAT6A patch cord 2 Mtr (7 feet) for information outlet (I/O) to

end user device connectivity. High Speed Gigabit 24AWG U/UTP Patch Cord, LSZH, C6

Supply, Installation, Testing and Comissioning of CAT6A patch cord 1 Mtr (3 feet) for information outlet (I/O) to Rack

End Redundant device connectivity. High Speed Gigabit 24AWG U/UTP Patch Cord, LSZH, C6

SITC of Access Switch with minimum of 48-port POE Data Switch, 48x10/100/1000 PoE+ ports, Virtual Networks 4,

Stacking bandwidth 160GBPS, Total number of MAC addresses 3200, Total number of IPv4 routes (ARP plus learned

11 routes) 14,000 (10,000 direct routes and 4,000 indirect routes), IPv4 routing entries 4000, IPv6 routing entries 2000, Nos 1 446,706.00 446,706.00

Multicast routing scale 1000, DRAM 4GB, Flash 4GB, Switching capacity 176GBPS, Forwarding rate 261.9 GBPS

Digitally signed by RAJ PAL

Schedule of Quantites: ACCESS CONTROL

S NO DESCRIPTION UNIT QUANTITY Rate DSR Amount NDSR Amount

Supply, Installation, Testing and Commisioning of Face detection Reader with Supports smart card

technologies mifare/Desfire, Face Capacity: 1000 minimum and upgradable, Reliable Face Recognition

1 Technology, 25-30 persons can punch in the reader in less than a minute,Ethernet connectivity for reliable Nos 15 46,039.00 690,585.00

communication, USB Host Data Transfer Complete all as per the RFP Specifications and Approval of

Engineer In-charge.

Supply, Installation, Testing & Commissioning of Web based Access Control and T&A software with

Intrusion and Alarm Managment Features. software should offer a comprehensive solution for managing

biometric devices, card readers, QR Reader, Bluetooth Readers, NFC Readers and access controllers. It

should enable users to enroll individuals' biometric data and controller information within a single

enrollment process. This ensures convenience and efficiency for system administrators. Additionally, the

software should support modules such as Access Control, Time & Attendance,Visitor Management,

Vehicle Access Management, Mobile based Attendance, Guard Tour Management, and other relevant

functionalities, all utilizing the same database, No separate database for any of the module will be allowed

except third party Integration if required, This promotes future scalability and streamlined data

management , The Time & Attendance software provides a comprehensive set of flexible functions to meet

2 various organizational requirements. These functions include the ability to manage multiple organizations, Nos 1 78,390.00 78,390.00

implement late-in and early-out policies, define overtime policies, handle absenteeism, manage multiple

holidays and holiday schedules, manually enter and correct entry-exit events, and generate attendance

summaries. These functions offer versatility in managing and monitoring employee attendance effectively.

Software should be a certified that meets the ISO 9001:2015 (Quality Management Systems), ISO

14001:2015 (Environmental Management Systems), and ISO 27001:2013 (Information Security

Management Systems) standards. These certifications validate the Software adherence to internationally

recognized standards in quality, environmental responsibility, and information security.The Software shall

have "Vulnerability Assessment Security Closure Report of Access Control and Time and Attendance

Software" along with Audit Certificate should be issued Cert-In Empanelled government Organizations

CDAC/STQC etc. Integration is required with the existing system of client at their existing office and

nothing extra shall be paid for the same.

Supply, Installation, Testing & Commissioning of Access IP Controller with Enclosure and Power Supply

Unit : 2 Door 4 Reader with RS485 OSDP, Security Features: Authorized IP address filtering, IP Client

Proxy Host communications protected by TLS 1.2/1.1 or AES 128/256 bit data encryption for optimal data

protection, Crypto memory chip, IO Expansion connection protected by AES Capacity: Cards/Users :

240000 Offline Event Log: 5,0000 & Communications Built in TCP/IP, IPV4, IPV6, RS-485, Inputs: Seven

unsupervised/supervised, Two unsupervised dedicated for cabinet tamper and UPS fault monitoring,

Outputs: Four relays, Power : 12 to 24 Vdc 10 %, 500 mA maximum , Supports up to 520 inputs and 516

3 outputs, 16 card formats per active reader, 8 per offline reader, Open Supervised Device Protocol (OSDP) Nos 7 59,555.00 416,885.00

and OSDP SC compliant, Anti-passback support, Area-based, reader-based, or time based Nested area,

hard, soft, or timed forgiveness, Encrypted database, Supports up to nineteen (19) digit card numbers,

Intrusion Alarm Functions: Area monitoring, Standard alarm masking , Fire Integration; open all doors from

hardware itself, Temperature: -55 to +85 °C, storage, 0 to +70 °C, operating, Humidity: 5 to 85 % RHNC,

Micro USB Port, SD card upto 8 GB. Certifications and Compliances:UL294 Recognized, FCC Part 15

Subpart B, CE Compliant, RoHS, NIST Certified Encryption etc. as per specifications of this tender etc

complete as required and directions of Engineer-in- Charge.

4 Supply, Installation, Testing & Commissioning of 12V, 5 Amp. SMPS with MS Box Certified . Nos 7 2,915.00 20,405.00

Supply, Installation, Testing & Commissioning of Smart card Mifare smart Card , distance upto 2.5"

Memory Type EEPROM, 1K bit memory Complies with ISO/IEC standards for thickness. Lifetime Warranty

.etc. as per specifications of this tender etc complete as required and directions of Engineer-in- Charge.

1 Digitally signed by RAJ PAL

Schedule of Quantites: ACCESS CONTROL

S NO DESCRIPTION UNIT QUANTITY Rate DSR Amount NDSR Amount

Supply, Installation, Testing & Commissioning of Electro Magnetic Lock Double Leaf as per door design,

Fail safe type, Holding force: 272kg(600lbs), Inbuilt Door contact , Current Drain:320mA/12VDC, Built-in

voltage spiker suppressor to protect the lock body and equipments, lock body and armature with chemical

plating anticorrosion finished, With LED light & Compatiable brackets (L/U/ZL), Bracket shall included as

per door's design only, CE Certified etc. as per specifications of this tender etc complete as required and

directions of Engineer-in- Charge.

Supply, Installation, Testing & Commissioning of Electro Magnetic Lock Single Leaf as per door design,

Fail safe type, Holding force: 272kg(600lbs), Inbuilt Door contact , Current Drain:320mA/12VDC, Built-in

voltage spiker suppressor to protect the lock body and equipments, lock body and armature with chemical

plating anticorrosion finished, With LED light & Compatiable brackets (L/U/ZL),Bracket shall included as

per door's design only, CE Certified etc.as per specifications of this tender etc complete as required and

directions of Engineer-in- Charge.

Supply, Installation, Testing & Commissioning of Stainless Steel SS 304 Grade, Push Button, Heavy Duty

Material , NO, NC Based, 4 Amp @125 VAC.

9 Supply Installation Testing and Commissioning of 8 Core -conductor20 to 22 AWG. Mtr 350 221.00 77,350.00

Supply Installation Testing and Commissioning of AC 3 Core Plain Copper conductor, PVC

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in

11 surface/recess including cutting the wall and making good the same in case of recessed Metre 500 201.00 100,500.00

conduit as required 25 mm.

2 Digitally signed by RAJ PAL

Schedule of Quantities: Integrated Audio Visual System

S No Item Description UoM QTY Rate DSR Amount NDSR Amount

SITC of Digital Standees with sleek and slim design with tempered glass protection with digital sinage and IR

1 touch option. Minimum 55" display for better viewing and for 24x7 operation with native resolution of Nos 1 152,940.00 152,940.00

1080x1920 and brightness 350cdm2 contrast ratio 5000:1 with all required accessiores

SITC of 86" 4k, UHD Professional Signedge Display with 500 NITS, 24*7 ,Built in SOC/ Media Playerwith Quad

Core Processor, Built in Open Platform Android 11, 3X HDMI, Audio Input Audio Output, Built in Speaker(12W

2 x 2) ;Including mounting bracket, Built-in Chromecast, Dolby Digtial audio HDMI-CEC device linking supported, Nos 1 459,385.00 459,385.00

3 USB(2.0), 3*HDMI(2.0 Side), Headphone Out, 1 *RJ 45, SPDIF out, Built In 2.4 GHZ Wifi,, With 3 years on

SITC of 75" 4k, UHD Professional Signedge Display with 400 NITS, 24*7 ,Built in SOC/ Media Player with

Quad Core Processor, Built in Open Platform Android 11, With Built in Bluetooth, 2X HDMI, Audio Input Audio

Output, Built in Speaker(10W x 2) ;Including mounting bracket, Built-in Chromecast , HDMI Arc, Dolby Digtial

3 audio, The built-in SOC is powered by Google's Android Platform, HDMI-CEC device linking supported, 2 Nos 4 260,798.00 1,043,192.00

USB(2.0), 3*HDMI(2.0 Side), Headphone Out, 1 *RJ 45, SPDIF out, Built In 2.4 GHZ Wifi,CPU Built in With

Cortex-A55*4, 1.1 GHz Processer, 2 GB RAM, 20 W built speakers, With 3 years on Site Warranty

SITC of 65" 4k, UHD Professional Signedge Display with 400 NITS, 24*7 ,Built in SOC/ Media Player with

Quad Core Processor, Built in Open Platform Android 11, With Built in Bluetooth, 2X HDMI, Audio Input Audio

Output, Built in Speaker(10W x 2) ;Including mounting bracket, Built-in Chromecast , HDMI Arc, Dolby Digtial

audio, The built-in SOC is powered by Google's Android Platform, HDMI-CEC device linking supported, 2

USB(2.0), 3*HDMI(2.0 Side), Headphone Out, 1 *RJ 45, SPDIF out, Built In 2.4 GHZ Wifi, With 3 years on

SITC of 55" 4k, UHD Professional Signedge Display with 500 NITS, 24*7 ,Built in SOC/ Media Player with

Quad Core Processor, Built in Open Platform Android 9, Surface Haze 28%,With Built in Bluetooth, 3X HDMI

2.0 , Audio Input Audio Output, Built in Speaker(10W x 2) ;Including mounting bracket, Built-in Chromecast,

5 Dolby Digital audio, The built-in SOC is powered by Google's Android OpenPlatform, 2 USB(2.0), 3*HDMI(2.0 Nos 4 106,278.00 425,112.00

Side), Headphone Out, 1 *RJ 45, SPDIF out, Built In 2.4 GHZ Wifi,CPU Built in With Cortex-A55*4, 1.1 GHz

Processer, 2 GB RAM & 16 GB Storage, 20 W built speakers, With 3 years on Site Warranty

SITC of 43" 4k, UHD Commercial Display with 400 NITS, 24*7 ,Built in SOC/ Media Player with Quad Core

Processor 2.4 GHZ Wifi, CPU Built in With Cortex-A55*4, 1.1 GHz Processer, Built in Google Certified Android

11 Operating System, 2.0GB, DDR3 2133Mhz and Memory Flash 16GB EMMC, Inbuilt OTT App,With Built in

6 Bluetooth, Audio Input & Audio Output, Built in Speaker(10W x 2), Built-in Chromecast , Basic Hotel Model Nos 5 69,750.00 348,750.00

Function ,HDMI Arc Function, Dolby Digital Audio, HDMI-CEC device linking supported, 2 USB(2.0) x 1 , USB

3.0 x 1, 3*HDMI(2.0 Side),HDR10/HLG, Headphone Out, 1 *RJ 45, SPDIF out, With 3 years on Site Warranty

SITC of Fixed Wall Mount, capable of holding up to 75 kg and supports 37" to 100" displays, VESA Compliant

etc all complete

SITC of E Ink Label 4.2 Inch E-paper Smart Label ESL Bluetooth and Customization Goodisplay etc all

SITC gateway per Tag Includes : Design and Selection of Accessories and Tag Placement Gateway Location

Identification for Optimized Operations, in line with Meeting Room Layout Gateway Mounting and Fixing

Accessories Estimation Tag Updating in the System Testing of All Tags Standard Template Design and Upload

etc all required

SITC of Ultra Thin Retractable Touch Monitor Lifter With Screen, Material: Full aluminum alloy, Monitor: 15.6

inch FHD Screen (16:9) , Resolution ratio: 1920*1080 , Screen Brightness: 400 cd/m2 , Contrast: 1500:1 Full

Angle Automatic Pitch Angle: 15 degree Manual Pitch Angle: 0-30 degree Interface: HDMI+RS232 I/O+USB

With Anti-Pinching Function etc all complete

Digitally signed by RAJ PAL

Schedule of Quantities: Integrated Audio Visual System

S No Item Description UoM QTY Rate DSR Amount NDSR Amount

SITC of Room booking system with remote and on-the-spot booking on an interactive touch screen, 6-inch(4.3)

interactive screen, full capacitive touch screen interface, has 3 month of battery autonomy or better, Resolution

1024 × 758 pixels.Viewing Angle 180°, connectivity 2.4 GHz Wi-Fi (IEEE 802.11 b/g/n) standard, WPA2-PSK

support, WPA2-EAP support etc all complete

SITC of Cable Cubby with flip top, cover and 6 Pass Through Holes for multi-format cables, 2 Universal Power

Socket , 1 HDMI, 1 USB-C for Data Transfer, made of aluminium etc all complete etc all complete

SITC of All in One Conference Unit, Camera Sensor 1/2.5″, CMOS, Effective Pixel: 8.0M, 4 x MEMS mic array,

AEC | ANS | AGC 180° Pickup Angle pickup Range: 5-8m (16-26ft) A.I. camera with smart backlighting, auto-

framing, speaker & presenter tracking, Inputs / Outputs 1x USB-C Input with Alt-Mode, 1x HDMI Input, 1x HDMI

Output etc all complete

SITC of Video conferencing Codec with Dual HDMI, supports 4K presentation, Support 256 AES Encryption,

4K PTZ camera with Group Framing and Lecturer tracking, 10.1”inch Touch Controller with mute and unmute

LED indicator, 1x IP Microphone with 20 feet range, POE+ Injector, 10 Meter HDMI cable, 3 year supportetc all

SITC of Universal Switcher with HDMI and USB-C connectivity, 2 HDMI Inputs, 2 USB-C connectivity (4K

Video, Audio, Data, Power charge), 2 HDMI Outputs, 4 USB-A 3.0 Connection (for USB Devices), 2

15 USB-B 3.0 Connection (for PC hosts), USB host switching, Analog audio de-embedding, Charging via USB- Nos 2 447,899.00 895,798.00

C up to 60w, Supports HDMI 4K signal formats (4K UHD @60Hz RGB 4:4:4, up to 18 Gbps), DP Alt Mode,

HDMI 2.0, HDMI 1.x, DVI Signal Support, HDCP 1.x, HDCP 2.2 support etc all complete

SITC of 2x1 matrix for AV over IP with USB-C, HDMI 2.0 and USB 2.0 ports Full 4K HDMI 2.0 transmitter (4K

UHD @ 60Hz RGB 4:4:4, up to 18 Gbps), Video, USB2.0, Ethernet, GPIO and Serial. USB-C connectivity for

4K video, audio, control signals and charging via USB-C up to 100W (120W total). Advanced automated room

automation/control features. etc all complete

SITC of Receiver for recieving HDMI 2.0 + RS-232 + bidirectional IR, over 10G copper network cable. HDCP,

3D and 4K / UHD ( 60Hz RGB 4:4:4 , 60Hz YCbCr 4:4:4) compliant with HDR support etc all complete

SITC of Receiver for receiving HDMI 2.0 + RS-232 + bidirectional IR, over 10G copper network cable with

18 analog audio output, KVM, and full USB2.0 support. HDCP, 3D and 4K / UHD ( 60Hz RGB 4:4:4 , 60Hz YCbCr Nos 1 302,425.00 302,425.00

4:4:4) compliant with HDR support. etc all complete

SITC of Control Unit (CU) for AV Over IP product line Directly accessible SDVoE API, 3 RJ45-type Ethernet

19 connectors for flexible network configuration, Occupancy sensor connector Two RS232 connectors for device Nos 1 228,286.00 228,286.00

control GPIO interface for device control etc all complete

Digitally signed by RAJ PAL

Schedule of Quantities: Integrated Audio Visual System

S No Item Description UoM QTY Rate DSR Amount NDSR Amount

Supply, installation, testing, and commissioning of Conference Controller that incorporates Digital Signal

Processing. The Controller should have the capability to control a minimum of 50 Discussion Units, with the

option to expand up to 150 Discussion Units by configuring multiple Controller Units. To ensure redundancy,

the Controller Unit should be equipped with 4 Bus Connections (4 branches or 2 closed loops). The Controller

should be accessible and configurable through an Integrated Web Server. Additionally, it should feature Two

USB Connections for connecting USB Storage Devices to enable direct recording of the meeting. In case the

First USB Storage Device becomes full, the Second USB Storage Device should automatically take over. The

Controller should also have the capability to integrate with Camera Control. It should be equipped with an LCD

20 a display to facilitate various Conference Modes, including Direct access, Request, Push to talk, FIFO, Vox Nos 1 455,000.00 455,000.00

control, Selectable Voice Activation, and Volume control ranging from 0 dB to -46 dB + "OFF". Furthermore, the

Controller should incorporate Digital Acoustic Feedback Reduction and offer Audio Input and Output

connectivity for external systems such as amplifiers, wireless microphones, and audio/video conference

systems. The Audio Quality should be 16Bit digital. The Controller should feature a Power Saving Mode that

allows it to enter a sleep state if left ON. In terms of connectivity, it should have Balanced XLR input, 1

Unbalanced RCA input, 2 Unbalanced RCA outputs, 4 Bus connections (4 branches or 2 loops), LAN

connection, 2 USB connections, and 1 Lockable Power connection. A Headphone Port should also be

included. The Controller should be certified with CE..

Supply, installation, testing, and commissioning of Chairman Discussion Unit with a Removable Microphone

measuring a minimum length of 400mm. The Chairman Discussion Unit should be equipped with built-in Digital

Signal Processing and come with Priority and Next-in-Line Configuration. The Priority button will silence all

delegate microphones, allowing only the chairperson to speak, while the Next-in-line button will give the floor to

the next speaker in a waiting list of speakers who have requested to speak. User Button with Feedback, a

shielded microphone that is immune to mobile phone interference, a high-quality integrated loudspeaker, a

headphone output with volume adjustment, and loop-through, daisy-chain cabling. Additionally, the unit should

20 b have a Bi-color bar indicator, be compatible with a Screw Lock Microphone measuring 400mm in length, and Nos 1 95,000.00 95,000.00

have different LED signaling for Mic On/Off or Request-to-Speak Push Button. The audio quality should be

16Bit digital, with a frequency response of 25 Hz-15,000 Hz (± 3 dB). The microphone should have a 400mm

gooseneck length, a unidirectional, cardioid polar pattern, a maximum SPL of 110 dB SPL (1% THD+N) at

1kHz, an S/N ratio of > 67 dB(A), and a sensitivity of (-40.5±2) dBV @ 1Pa, 1kHz. The microphone should also

feature a ring indicator that lights up red when active and green when in request mode. The connection should

be a screw lock, and the material should be brass. The unit should be certified with CE and BIS.

Supply, installation, testing, and commissioning of Delegate Discussion Unit with a Removable Microphone

measuring a minimum length of 400mm. The delegate Discussion Unit should be equipped with built-in Digital

Signal Processing and come with on off button, User Button with Feedback, a shielded microphone that is

immune to mobile phone interference, a high-quality integrated loudspeaker, a headphone output with volume

adjustment, and loop-through, daisy-chain cabling. Additionally, the unit should have a Bi-color bar indicator, be

compatible with a Screw Lock Microphone measuring 400mm in length, and have different LED signaling for

Mic On/Off or Request-to-Speak Push Button. The audio quality should be 16Bit digital, with a frequency

response of 25 Hz-15,000 Hz (± 3 dB). The microphone should have a 400mm gooseneck length, a

unidirectional, cardioid polar pattern, a maximum SPL of 110 dB SPL (1% THD+N) at 1kHz, an S/N ratio of >

67 dB(A), and a sensitivity of (-40.5±2) dBV @ 1Pa, 1kHz. The microphone should also feature a ring indicator

that lights up red when active and green when in request mode. The connection should be a screw lock, and

the material should be brass. The unit should be certified with CE and BIS.

SITC of Audio, Video and Control (AV&C) Processor, 64 x 64 audio channels, 8 Input channels and GPIO, Full-

21 featured Control engine (with feature license), 8 AEC Processors, up to 32 x 32 Dante audio channels (8 x 8 Nos 1 467,999.00 467,999.00

included), USB AV bridging, Full-featured Q-SYS Control engine (with optional feature license).

Digitally signed by RAJ PAL

Schedule of Quantities: Integrated Audio Visual System

S No Item Description UoM QTY Rate DSR Amount NDSR Amount

SITC of 6.5-inch, 2-Way Ceiling Speaker, Rated Power: 60W, Frequency Range: 65 Hz – 20 kHz, Sensitivity:

88 dB, Rated Coverage 135° conical DMT, Maximum continuous SPL 106 dB, Nominal impedance: 8 / 16

Ohm, Transformer taps: 60W / 30W / 15W at 100 / 70V, IP-34 Rated, Low-saturation and low-loss 70/100V

transformers with 16Ω bypass, UL and CE Certified etc all complete

SITC of 4 Channel Class-D Amplifier, Power (per channels driven): 200 W at 8 Ω / 4 Ω / 100V / 70V, FlexAmp

Technology, Frequency Response: 20 Hz – 20 kHz, Signal to Noise > 103 dB, Input impedance >10k, balanced

or unbalanced, User-configurable operating modes, UL, CE, RoHS/WEEE compliant etc all complete

SITC of 4 x 4 USB 3.2 Gen 1 Industrial Hub Switch, Enables 4 computers to share 4 USB 3.2 Gen1 devices

24 Support port selection via remote controller or RS-422/RS-485 link through 5-pin terminal block Supports DC 9- Nos 1 69,898.00 69,898.00

24V power input by terminal block, Supports USB BC 1.2 and over current protection

SITC of Expension Module for RS232 /RS485/RS422 Communication Port, Gigabit LAN, Four bi-directional

RS232 serial ports, Power over Ethernet (PoE) capable etc all complete

Supply, Installation, Testing & Commissioning of High Definition, In wall Multi-touch Touch Screen Controller

with 24-bit color display. Viewable Screen Dimensions (diagonal) – 7-inch or better, Resolution - 1280 × 800 or

26 better, Brightness - 400 Nits or better, Aspect ratio – 16:10 or better, Power – PoE or better, Mounting – Wall Nos 1 305,950.00 305,950.00

and Tabletop, Orientation - Vertical / horizontal. Configurable LED’s on both side or similar for status indication.

Sensors - Ambient Light Sensor, Proximity Detection or better.

SITC of 8-Port Gigabit PoE+ Ethernet Smart Switch with 2 SFP Ports and Cloud Management etc all complete

28 SITC of Wireless Access Point etc all complete Nos 1 29,648.00 29,648.00

SITC of 2 Meter Premium High Speed HDMI 2.0b Flexy Cable, Bandwidth up to 18Gbps, Up to

29 4096x2160@60Hz at RGB 4:4:4 video resolution, High Dynamic Range (HDR10), Dolby Vision and Hybrid Nos 47 4,975.00 233,825.00

log–gamma (HLG) video etc all complete

SITC of 15 Meter Active Copper HDMI Cable, Data Rate: Up to 18.2Gbps, Colour Depth: Up to 16 bits, Colour

Formats: RGB 4:4:4 / Y’CBCR 4:2:2 / Y’CBCR 4:2:0, Consumer Electronic Control (CEC), Auto Lip-Sync

Correction, Audio Return Channel (ARC), Enhanced Audio Return Channel (eARC), High Dynamic Range

(HDR) etc all complete

SITC of 2 Meter USB Full-Featured Type-C cable for USB 3.1 Gen2, 4 Lane Displayport Alt mode (4K60FPS

31 Video and Audio), Supporting peripherals via USB 2.0 up to 480 Mbps (Mouse, Keyboard, Thumb Drive, Nos 21 5,980.00 125,580.00

Speakerphone and Webcam) etc all complete

SITC of 15 Meter USB 3.1 Gen1 SuperSpeed Active Extension Cable TypeA/male to TypeA/female, Supports

32 4K Webcam, SSD storage, Native USB2/USB1 and USB3 extension, Plug and play compatible with PC, Mac, Nos 9 77,054.00 693,486.00

and Linux etc all complete

SITC of 2 Conductor 16 AWG Speaker Cable, stranded Bare copper conductors, PVC/Nylon insulation, PVC

jacket (as per actual) etc all complete

34 SITC of Category 6A Cable, 4 Pair, S/FTP, PVC jacket (as per actual) etc all complete Metre 305 80.00 24,400.00

35 SITC of Various Cables, relay modules & Connectors etc all complete Nos 30 14,573.00 437,190.00

SITC of 16U, Equipment Rack, with Front & Side doors, 4 No Fan Assembly, on Top of the Rack, 4 Caster

36 wheels, 2 no Shelfs to mount the equipments which are not rack mounted, 8X2, 5/6 Amp. Power Distribution Nos 1 31,708.00 31,708.00

Unit, Cable Manager & Sufficient Rack hardwares etc all complete

Digitally signed by RAJ PAL

SCHEDULE OF QUANTITIES - FIRE ALARM

S NO DSR/MR DESCRIPTION UNIT RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR NON DSR

SITC of UL268 10th edition compliance and FM approved Intelligent Addressable multi- criteria detector

(optical and thermal sensors) complete with standard base, facility to mount in different comprehensive

environment, Tri-color detector-status LED with 360 ° view, microprocessor circuitry with error

check; detector self-diagnostics and supervision programs,Rate-of-Rise Detection: 15°F / min.

(8.3°C / min.) - Fixed: 135°F (57°C) , Field programmable as rate-of-rise or fixed temperature, Polarity

insensitive, Superior EMI and RFI immunity, RoHS compliant. Detector shall have in-built isolator for

better reliability, circuit integrity and advanced fault finding. Manufacturers not having in-built Isolator

feature in detector shall consider Isolator base in place of standard base OR separate Isolator before

and after every detector to comply the same without any extra cost. It shall include

surface/recessed MS Box complete with all connections etc as required.

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two

LED, metallic cover complete with all connections etc as required.

SITC of UL Listed and FM approved Intelligent Addressable Rate of Rise and Fixed

temperature detector complete with standard base, Seven (7) field-selectable settings in a temperature

range of 135°F – 174°F (57.2°C – 78.9°C) , a low-temperature warning of 40°F (4.4°C), facility to

mount in different comprehensive environment, Tri-color detector-status LED with 360 ° view,

microprocessor circuitry with error check; detector self-diagnostics and supervision programs, Field

programmable as rate-of-rise or fixed temperature, Polarity insensitive, Superior EMI and RFI

immunity, RoHS compliant. Detector shall have in-built isolator for better reliability, circuit integrity and

advanced fault finding. Manufacturers not having in-built Isolator feature in detector shall consider

Isolator base in place of standard base OR separate Isolator before and after every detector to

comply the same without any extra cost.

Supplying, installation, testing & commissioning of fault isolator complete with base as required.

SITC of UL Listed Sounder cum Strobe rated at 75 dBA @ 3m for Audible annunciation and 75cd

flashintg at 1 Hz for visual indication.

SITC of UL listed and FM approved Intelligent addressable Class X type (Style 7), Control Module

with built in dual isolator, polarity insensitive, Tri color LED for status (Green for Normal,Yellow for

Faulty and RED for activation), Operating Temp and RH: 0-49 deg C and <=95%. Module shall have

in-built isolator for better reliability, circuit integrity and advanced fault finding. Manufacturers not having

in-built Isolator feature shall provide separate Isolator before and after every Module to comply the same

without any extra cost. (For AHU & Staircase Pressurization Fans, Hooters/ Sounders/ Strobes etc.)

Supplying, installation, testing & commissioning of addressable phone control module complete as

SITC of UL listed and FM approved Intelligent addressable Class X type (Style 7), Monitor Module

with built in dual isolator, polarity insensitive, Tri color LED for status (Green for Normal,Yellow for

Faulty and RED for activation), Operating Temp and RH: 0-49degC and <=95%. Module shall have in-

built isolator for better reliability, circuit integrity and advanced fault finding. Manufacturers not having

in-built Isolator feature shall provide separate Isolator before and after every Module to comply the same

without any extra cost. (For Flow Switch Monitoring/ Gass suppresion Integration etc.)

Digitally signed by RAJ PAL

SCHEDULE OF QUANTITIES - FIRE ALARM

S NO DSR/MR DESCRIPTION UNIT RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR NON DSR

SITC of UL268 10th edition compliance and FM approved Intelligent Addressable Duct detector with

10ft sampling pipe (optical and thermal sensors) complete with standard base, facility to mount in

different comprehensive environment, Tri-color detector-status LED with 360 ° view, microprocessor

circuitry with error check; detector self-diagnostics and supervision programs,Rate-of-Rise Detection:

9 MR 15°F / min. (8.3°C / min.) - Fixed: 135°F (57°C) , Field programmable as rate-of-rise or fixed temperature, Nos 4.00 19,551.00 78,204.00

Polarity insensitive, Superior EMI and RFI immunity, RoHS compliant. Detector shall have in-built isolator

for better reliability, circuit integrity and advanced fault finding. Manufacturers not having in-built Isolator

feature in detector shall consider Isolator base in place of standard base OR separate Isolator before and

after every detector to comply the same without any extra cost.

SITC of UL listed and FM approved Intelligent addressable Class X type (Style 7), Manual Pull

Station Single Action, Shock and Vibration Resistant, with built in dual isolator, polarity insensitive, Tri

color LED for status (Green for Normal,Yellow for Faulty and RED for activation), T-45 Key Reset

10 MR lockset for easy maintenance, Operating Temp and RH: 0-49degC and <=95%. MCP shall have in-built isolator Nos 4.00 6,384.00 25,536.00

for better reliability, circuit integrity and advanced fault finding. Manufacturers not having in-built Isolator

feature shall provide separate Isolator before and after every MCP to comply the same without any extra

Supplying, installation, testing & commissioning of One controller supports 12 zones, expandable up-to 492

11 MR zones with 24-zone routers, Control and routing of 4 simultaneous audio channels,EN 54-16 system Nos 1.00 379,832.00 379,832.00

SITC of Call station with soft touch button 15 freely programmable buttons,Customization via built-in display

12 MR and keys, Provision for installing emergency button and key switch,EN 54-16 system certification etc all Nos 1.00 178,560.00 178,560.00

13 MR Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as required. Nos 110.00 1,401.00 154,110.00

Supplying, installation, testing & commissioning of Power amplifier, 480W,Multiple outputs - 70 V / 100 V

14 MR and 8/4 ohm, Temperature controlled forced front to back ventilation, directly stackable, Mains, battery back- Nos 1.00 135,938.00 135,938.00

up, and pilot tone supervision, Dual inputs with priority switching complete as required.

Supplying & laying of 2x1.5 sqmm fire alarm FS armoured cable, 600/1000V rated with annealed

15 MR copper conductor having XLPE insulation, steel wire armouring & FS outer sheath complete as required Mtr 1,620.00 254.00 411,480.00

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing

surface / recessed steel conduit of following pairs, cores and size including connections and

interconnections etc. as required.

Supplying and Laying of 2x1.5sqmm FS unarmourd cable

Supplying and fixing 25 mm dia MS flexible pipe with PVC coating along with all ancillaries and accessories

like coupler etc. as required.

Supplying & Fixing of battery operated illiminated "EXIT" signage, with 2hrs power Battery backup

complete as required.

SITC of Remote Paging Microphone should be fully digital connected via CAT6 Cable with Controller.

The Microphone should have capability to make announcement in 96 Zones and have all call facility.

The Microphone shall have ability to control music and should be able to route the music in zones. Microphone

should have maximum zones capacity up to 120 Zones. The Microphone should have LED indication for

the different faults, the unit shall be able to indicate AC, DC, Fault, Mic and Test status through LED.. The

Unit shall have 2 RJ45 ports for Microphone so that the other microphone shall be able to link with the

unit. The Microphone shall have ability to Communication limit up to 600 Meters

Digitally signed by RAJ PAL

SCHEDULE OF QUANTITIES - FIRE ALARM

S NO DSR/MR DESCRIPTION UNIT RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR NON DSR

Supply, Installation, Testing and Commisioning of Interface Card for BMS fire integration compatible

with exisiting system

Supply, Installation, Testing and Commisioning of repeater panel having 160 character display with

backlit control compatible with existing system

SITC of UL864 10th Edition UL Listed and FM approved Analog Addressable 4 Loop Fire Alarm

control panel. Panel shall be running on full digital protocol with 32 bit Microprocessor . The Panel shall be

complete with 6" color touch screen LCD Display. Fire alarm panel should have minimum capacity of 2500

detectors and devices in any combination and capable of making upto 50 loops in single panel using

additional Loop cards. Each addressable loop shall be capable of taking 250 addresses per loop

configuring either as all detectors or modules or any mix of both. The panel shall have the Fire

Fighter Touch Screen Graphical Display panel to inform & guide Fire Fighters for carrying out Fire

Fighting operations. The display shall have Hazmat icons indicating the presence of any

22 MR explosive gas, liquids, poison,fumes etc. If this feature is not available in fire alarm panel then Nos 1.00 444,220.00 444,220.00

additional fire fighter touch panel along with necessary hardware and software should be

provided by the manufacturers for fire fighters to guide them during emergency without any extra

cost. To expedite system troubleshooting, the system cards shall have ground fault detection and

diagnostic LEDs by card. In the display,simple building floor plan can be loaded in bitmap or jpeg format,

On the map, the user will see an icon indicating the location of the event in the building in addition to

a 'You-Are-Here' symbol to tell the responding person exactly where they are in the building in relation to the

event. The system shall be polarity insensitive. The panel shall support degrade mode operation and shall

have battery backup of 24 hrs in normal condition and 30 minutes in Alarm condition.

Digitally signed by RAJ PAL

SCHEDULE OF QUANTITIES: FIRE PIPING, HYDRANTS, SPRINKLERS AND ACCESSORIES

S No DSR 2022/ DESCRIPTION QTY UNIT RATE TOTAL TOTAL AMOUNT

S No DSR 2022/ DESCRIPTION QTY UNIT RATE TOTAL TOTAL AMOUNT

DSR (INR) NON-DSR (INR)

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe

conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees,

18.7 flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling

1 with suitable clamp/support frame and painting with two or more coats of

synthetic enamel paint of required shade complete as required :

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type

2 sprinklers of rating 68 degree centigrade with required accessories :

18.21.1 Pendant type 410 Each 522.00 214020.00

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL

Listed) of stainless steel complete with 15 NPT on reducer thread with

maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with

branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT

female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of

following sizes complete as required.

Providing and fixing ISI Marked of approved make Fire Extinguishers complete

with all accessories as per manufacturer's specifications.

a) MR CO2 gas nozzle type - 9 Litre capacity (IS:15683). 4 NOS 12912.00 51648.00

b) Mechanical Foam gas cartridge type. 9 Kg capacity (IS:15683). 4 NOS 2932.00 11728.00

c) ABC dry powder stored pressure type 6 kg capacity (IS:15683). 4 NOS 4746.00 18984.00

Digitally signed by RAJ PAL

SCHEDULE OF QUANTITIES: FURNITURE

S No Item Description Technical Specifications Category/ Area QTY Rate Images for Ref. Only

Director Room Table & Side Table

Overall Size : W 2300 x D 1000 x H 750mm & Side Unit Extention: W 1400 x D 550 x H 600mm.Back Unit Overall Size

W 1500 x D 600 x H 750mm. The table shall be made of partical and MDF board E1 norms with verneer finish.The

tabletop shall be 45mm thick supported on 3 drawer pedestal and side return unit. The front modesty shall be made up

of 18mm thick pre laminate partical board with the 600mm height.The side table design should be such that it has

flexibility to be fixed either in right hand side or left hand side of the user during the time of assembly.3 equal drawer top

1 MD Room Table MD ROOM 1 590000 590000

supported pedestal shall be provided under the table top. Side return unit shall be 1400L x 550D 600H shall be made of

of partical and MDF board E1 norms with verneer finish. The side unit shall consist of 3 drawer and openable shutter

with all the hardware like hings and handle.Back Unit Overall Size W 1500 x D 600 x H 750mm shall be made of of

partical and MDF board E1 norms with verneer finish.The back unit shall consist of openable shutter made of 18mm

thick pre laminate partical board with all side pvc edge band.The OEM shall ISO 9001, BIFMA Level 2 certification &

IGBC gold certified manufacturing facility.

High Back Chair : The overall size of Chair shall be Total height 1150 to 1250 +/-5 mm, over all width should be 520 +/-

5mm and Overall depth should be 470 +/-5mm. Back Width 360 mm at Top and 500mm at bottom, Seat Width 520 +/-5

mm, Seat Depth 470+/-5 mm and Seat height 455mm to 555 mm +/-5mm. Seat & back PU cushion shall be uplhostered

with pure leather on user touch points. The Chair should be provided with Synchro tilt Mechanism with Multi lock

features. The mechanism shall allow 360 degree revolving feature along with height adjustablility. Single die casted right

trapezium shaped arm rest overall size of 250 L x 190 H & having top upholstered leather on top. The width of the

2 MD Leather chair MD chair 1 52000 52000

armrest shall be 60mm and overall length on top surface shall be 260mm. The chair back shall have S-curved. Multi lock

and seat adjustable nob shall be provided on the left side below the seat. Tension adjustment knob shall be provided

under seat. The Gas Lift used shall be class 4 tested as per ANSI BIFMA standards. Chair shall be provided with

aluminium die cast pedetstal having twin castors 50 mm dia with PA6 material complying to ANSI/ BIFMA X 5.1 2017

standards. The OEM shall ISO 9001, BIFMA Level 2 certification & IGBC gold certified manufacturing facility.

Mid Back Chair : The overall size of Chair shall be Total height 1050 to 1150 mm, over all width should be 520 mm and

Overall depth should be 470 mm. Back shall be tappered design having width 360 mm at top and 500mm at bottom,

Seat Width 520 mm, Seat Depth 470 mm and Seat height 455mm to 555 mm. Seat & back PU cushion shall be

uplhostered with leatherette. The Chair should be provided with Synchro tilt Mechanism with Multi lock features. The

mechanism shall allow 360 degree revolving feature along with height adjustablility. Single die casted right trapezium

3 shaped arm rest having overall size of 250 L x 190 H & having top upholstered leather with foam. The width of the MD visitor chair 3 43000 129000

armrest shall be 60 mm and overall length on top surface shall be 260mm. The chair back shall have S-curved. Multi

lock and seat adjustable nob shall be provided on the left side below the seat. Tension adjustment knob shall be

provided under seat. The Gas Lift used shall be class 4 tested as per ANSI BIFMA standards. Chair shall be provided

with aluminium die cast pedetstal having twin castors 50 mm dia with PA6 material complying to ANSI/ BIFMA X 5.1

2017 standards. The OEM shall ISO 9001, BIFMA Level 2 certification & IGBC gold certified manufacturing facility.

The overall size of the sofa shall be 2350 L x 790 D x 790 H. Sofa inner frame structure shall be made mainly from the

combination of treated pine wood of 20-25mm thick & neem based plywood sheets. The polyurethane (PU) foam of

density 32 and 40 shall be used in seat constructions and 32 density foam used in back construction along with the

webbing belts. Seat height should be 440mm (+/- 10mm) and seat depth shall be 525mm (+/- 20mm). Each sofa MD ROOM &

individual set type shall consist of 4 metal legs of 200 mm height that shall be laser cut and press formed in 2mm thick EXECUTIVE

CR steel in complaince with IS 513: 2008. The legs shall be formed in V-shape with 125 x 125mm length flanges on its WAITING

top face and moulded leg bush shall be fixed at its bottom that shall support height adjustment of upto 10mm. To suppor LOUNGE

thte sofa two nos wide flanges of the leg shall be be provided. Legs shall be pretreated through nano ceramic process

that shall be environment friendly to enable powder coating to the thickness of 50-80 microns. The fabric used shall be

450-475 gms per meter having abrasion resistance of more than 50K rubs high quality polyester fabric.The OEM shall

The overall size of the sofa shall be 850 L x 790 D x 790 H. Sofa inner frame structure shall be made mainly from the

combination of treated pine wood of 20-25mm thick & neem based plywood sheets. The polyurethane (PU) foam of

density 32 and 40 shall be used in seat constructions and 32 density foam used in back construction along with the

webbing belts. Seat height should be 440mm (+/- 10mm) and seat depth shall be 525mm (+/- 20mm). Each sofa

individual set type shall consist of 4 metal legs of 200 mm height that shall be laser cut and press formed in 2mm thick

Single seater CR steel in complaince with IS 513: 2008. The legs shall be formed in V-shape with 125 x 125mm length flanges on its MD ROOM

sofa top face and moulded leg bush shall be fixed at its bottom that shall support height adjustment of upto 10mm. To suppor SOFA

thte sofa two nos wide flanges of the leg shall be be provided. Legs shall be pretreated through nano ceramic process

that shall be environment friendly to enable powder coating to the thickness of 50-80 microns. The fabric used shall be

450-475 gms per meter having abrasion resistance of more than 50K rubs high quality polyester fabric. The OEM shall

ISO 9001, BIFMA Level 2 certification & IGBC gold certified manufacturing facility.

The overall size of glass table shall be 1200L x 600W x 425H. The table top shall be made of 8mm thick toughned

glass. The understructure shall be made of 19mm SS round tube. Leg shall be provided ABS shoe to protect from MD ROOM &

streched.The OEM shall ISO 9001, BIFMA Level 2 certification & IGBC gold certified manufacturing facility. EXECUTIVE

6 Center table 3 18723 56169

Digitally signed by RAJ PAL

SCHEDULE OF QUANTITIES: FURNITURE

S No Item Description Technical Specifications Category/ Area QTY Rate Images for Ref. Only

The overall size of glass table shall be 600L x 600W x 505H. The table top shall be made of 8mm thick toughned glass.

The understructure shall be made of 19mm SS round tube. Leg shall be provided ABS shoe to protect from MD ROOM &

streched.The OEM shall ISO 9001, BIFMA Level 2 certification & IGBC gold certified manufacturing facility. EXECUTIVE

7 Side table 6 13950 83700

The overall size of table shall be 2400L x 1900D x 760H. The main table top shall be size of 2200L x 950D with return

table shall be size of 1900L x 600D x 600H.The table top shall be made of 70mm thick E1 grade MDF with 0.6mm

natural walnut veneer and shall be 8 layers painting finish. The table top shall be resting on one side of side unit and

other side of gable end. Table gable end shall be made of 70mm thick E1 grade MDF with 0.6mm natural walnut veneer,

8 layers painting finish. The table front modesty shall be provided with 390mm height.The side table design should be

CEO and CGM such that it has flexibility to be fixed either in right hand side or left hand side of the user during the time of assembly. CEO and CGM

Table Fixed side return with 2 drawers, single swing door and open space for CPU, with holes for customer put their sockets. Room

Wire Management: 1 No. Aluminium Flip Up and provision to mount swicthes and sockets on metal cable Dump and

vertebra considered for wire uptake from floor to cable dump.Two pieces wirebox on table top, one is multi-functional for

wiring management and another just cover.Top covered by PU leather.The OEM shall ISO 9001, BIFMA Level 2

certification & IGBC gold certified manufacturing facility.

The overall size of Chair shall be : Back width: 480 mm, Total height: 1175 – 1275 mm, Back height- 705 mm. Seat

width: 500 mm, Seat depth: 460 mm, Seat height: 465-565 mm. Seat & Back shall duly upholstered with leatherette .

Leatherette shall of 75% PVC & 25% polyester – 630 GSM, Abrasion resistance of 50,000 cycles.Fixed armrest shall be

provided made of aluminium arms for luxury ergonomic chair. Knee tilt mechanism shall be provided having tilt tension

adjustment & height adjustment at same level on right hand side of user & any position locking level at the left hand side

of user.Singleswage Gas lift - Class 4 tested -ANSI BIFMA performance standards. The pneumatic height adjustment

CEO High Back shall have adjustment stroke of 95 -100 mm as per the seat height criteria and 360° revolving.The 660mm dia (26 CEO Room and

Chair inches) five pronged base shall be made out of Aluminium casting process, Reinforced with bottom ribbing for additional CGM chair

strength. The base shall be 107 mm height, 660 mm pitch centre diameter & 760 mm with castors. It shall be with

Aluminium natural color.

The overall size of Chair shall be : Back width: 480 mm, Total height: 945 - 1045 mm, Back height- 475 mm. Seat width:

500 mm, Seat depth: 460 mm, Seat height: 465-565 mm. Seat & Back shall duly upholstered with leatherette .

Leatherette shall of 75% PVC & 25% polyester – 630 GSM, Abrasion resistance of 50,000 cycles.Fixed armrest shall be

provided made of aluminium arms for luxury ergonomic chair. Knee tilt mechanism shall be provided having tilt tension

adjustment & height adjustment at same level on right hand side of user & any position locking level at the left hand side

CEO Visitor Back of user.Singleswage Gas lift - Class 4 tested -ANSI BIFMA performance standards. The pneumatic height adjustment CEO Room and

Chair shall have adjustment stroke of 95 -100 mm as per the seat height criteria and 360° revolving.The 660mm dia (26 CGM chair

inches) five pronged base shall be made out of Aluminium casting process, Reinforced with bottom ribbing for additional

strength. The base shall be 107 mm height, 660 mm pitch centre diameter & 760 mm with castors. It shall be with

Aluminium natural color.

The overall size of the sofa shall be 1750 L x 790 D x 790 H. Sofa inner frame structure shall be made mainly from the

combination of treated pine wood of 20-25mm thick & neem based plywood sheets. The polyurethane (PU) foam of

density 32 and 40 shall be used in seat constructions and 32 density foam used in back construction along with the

webbing belts. Seat height should be 440mm (+/- 10mm) and seat depth shall be 525mm (+/- 20mm). Each sofa

individual set type shall consist of 4 metal legs of 200 mm height that shall be laser cut and press formed in 2mm thick

12 2 seater sofa CR steel in complaince with IS 513: 2008. The legs shall be formed in V-shape with 125 x 125mm length flanges on its CEO Room 2 58824 117648

top face and moulded leg bush shall be fixed at its bottom that shall support height adjustment of upto 10mm. To suppor

thte sofa two nos wide flanges of the leg shall be be provided. Legs shall be pretreated through nano ceramic process

that shall be environment friendly to enable powder coating to the thickness of 50-80 microns. The fabric used shall be

450-475 gms per meter having abrasion resistance of more than 50K rubs high quality polyester fabric. The OEM shall

ISO 9001, BIFMA Level 2 certification & IGBC gold certified manufacturing facility.

The overall size of glass table shall be 1200L x 600W x 425H. The table top shall be made of 8mm thick toughned

glass. The understructure shall be made of 19mm SS round tube. Leg shall be provided ABS shoe to protect from

streched.The OEM shall ISO 9001, BIFMA Level 2 certification & IGBC gold certified manufacturing facility. CGM

13 Center table 6 18723 112338

Digitally signed by RAJ PAL

SCHEDULE OF QUANTITIES: FURNITURE

S No Item Description Technical Specifications Category/ Area QTY Rate Images for Ref. Only

The overall size of table shall 2000L x 800D x 780H with Side Unit Extention 1010L x 500D x 650H. The table top shall

be made of 25mm thick with Pre laminate Partical board with all side 2mm pvc edge band finish. The working table top

shall have size of 1800L x 800D. The table top visible side shall be 50mm thick. The edge of table top shall be cover

with L-shaped alumimum extrusion with size of 10mm x 15mm.This aluminium extrusion shall increase the overall look of

the table top.The main table top shall be supported on one side top supported pedestal and other side of side unit. 3

equal drawer unit shall be provided with size of 495 W x 800D x 650H. The drawer unit shall be made of 18mm thick pre

laminate partical board with 2mm pvc edge band finish.The front modesty shall be made of 18mm thick pre laminate

Partical board with 450mm height. Modesty shall be fitted on gable end with helps of mini fix. Wire Management: 1 No.

Aluminium Flip Up and provision to mount swicthes and sockets on metal cable Dump and vertebra considered for wire

Cabin table with

uptake from floor to cable dump. Side return unit shall have overall size of 1010L x 500D x 650H.The body of side unit

14 side and back GM cabin 5 155109 775545

shall be made of 18mm thick pre laminte Partical board with 2mm PVC edge band finish.The side table design should be

such that it has flexibility to be fixed either in right hand side or left hand side of the user during the time of assembly.

The side unit shall have one openeble shutter with 2 equal compartment to keep the documents and rest area shall have

open compartment.The overall size of Back unit shall be 1800L x 400D x 2000H. The back unit top shall be made of

25mm thick pre laminate partical board with 2mm pvc edge band on all the side. The side pannel shall have made of

18mm thick pre laminate partical board with 2mm pvc edge band finish all the visible side. The storage consist of 2

openeble door with size of 450W x 1940H and 2 openable shutter with height of 780mm at the floor level. In middle of

the storage shall have openable compartment and the shelf of openable compartment shall be made of 25mm thick pre

laminate partical board with 2mm pvc edge band in the viasible side of shelf. The door shall be operated by leatherette

strip handle. The OEM shall ISO 9001, BIFMA Level 2 certification & IGBC gold certified manufacturing facility.

Mid Back Chair: The overall size of Chair shall be height 1050 to 1170 +/-5 mm, Back Width 495 mm at Top and 385mm

at bottom, Seat Width 500 +/-5 mm, Seat Depth 390 to 450 +/-5 mm and Seat height 480mm to 600 mm +/-5mm range.

And over all chair width should be 690 +/-5mm and Overall chair depth should be 630 to 690 +/-5mm. Seat should be

made up of foam pre moulded at 55 kg/m3 density. hardness of 25+ 3kgf at 50% deflection conforming to IS 3400. Seat

shall be upholstered with Polyester & viscose- 380 GLM, Abrasion- > 45000 cycles. The chair shall be supplied with

Lenear Mesh at the back & shall be provided With 290mm width, 180mm height Headrest. Adjustable Lumbar Support

full length of size 325 mm,105 mm height and 3mm thickness in contoured form can travel upto 30mm at the back . The

Revolving chair

15 Chair should be provided with knee tilt Mechanism with Multi lock features. The mechanism shall allow 360 degree GM 5 21,950 109750

revolving feature along with height adjustablility. chair shall have seat sliding mechanism.Four Way Adjustable Arms to

be provied with height adjustment button made of Delrin P 500 and arm height adjustability nob shall be provided under

the armrest. The mechansim shall possess seat to back recline ratio of 3:7.Tension adjustment knob shall be provided

under seat. The Gas Lift used shall be class 4 tested as per ANSI BIFMA standards. Nylon Base to be provied. Twin

castors 60 mm dia with PA6 material complying to ANSI/ BIFMA X 5.1 2017 standards.The Back, Armrest and pedestal

shall be provided in same Grey colour.The OEM shall ISO 9001, BIFMA Level 2 certification & IGBC gold certified

manufacturing facility.

The overall size of Chair shall be height 915 to 1015 +/-5 mm, Back Width 415 mm at Top and 450mm at bottom, Seat

Width 480 +/-5 mm, Seat Depth 440+/-5 mm and Seat height 460mm to 560 mm +/-5mm range. over all chair width

should be 560 +/-5mm and Overall chair depth should be 670 +/-5mm. Seat should be made up of foam pre moulded at

55 kg/m3 density. hardness of 25+ 3kgf at 50% deflection conforming to IS 3400. Seat shall be upholstered with micro

fabric 100% polyster 180 GSM abrasion > 50000 cycles. No flamming or progressive smoldering within one hour of

placement of the cigarettes. Fire rated fabric confirming to BS EN 1021 (match) should be used. The back frame shall

be made up of PPGF and the injection molded in grey color, armrest also in grey color. The chair shall be supplied with

16 Revolving chair Mesh Back rest. The Chair shall be Greenguard certified. The Chair should be provided with center tilt two position lock GM 15 11931 178965

Mechanism. The mechanism shall allow 360 degree revolving feature along with height adjustablility. Fixed arms

connected to seat and back in the same contour. The mechansim shall possess seat to back recline ratio of 1:1. The

Gas Lift used shall be class 4 tested as per ANSI BIFMA standards. Nylon Base in grey color to be provied. Twin

castors 50 mm dia with PA6 material complying to ANSI/ BIFMA X 5.1 2017 standards. the axle pin shall be rust

protected zinc passivated. The base shall be made up of mild steel powder coated in grey shade to match the entire

grey theme of chair.The OEM shall ISO 9001, BIFMA Level 2 certification & IGBC gold certified manufacturing facility.

The overall size of the sofa shall be 2350 L x 790 D x 790 H. Sofa inner frame structure shall be made mainly from the

combination of treated pine wood of 20-25mm thick & neem based plywood sheets. The polyurethane (PU) foam of

density 32 and 40 shall be used in seat constructions and 32 density foam used in back construction along with the

webbing belts. Seat height should be 440mm (+/- 10mm) and seat depth shall be 525mm (+/- 20mm). Each sofa

individual set type shall consist of 4 metal legs of 200 mm height that shall be laser cut and press formed in 2mm thick

CR steel in complaince with IS 513: 2008. The legs shall be formed in V-shape with 125 x 125mm length flanges on its

17 3 seater sofa Reciption 15 69000 1035000

top face and moulded leg bush shall be fixed at its bottom that shall support height adjustment of upto 10mm. To suppor

thte sofa two nos wide flanges of the leg shall be be provided. Legs shall be pretreated through nano ceramic process

that shall be environment friendly to enable powder coating to the thickness of 50-80 microns. The fabric used shall be

450-475 gms per meter having abrasion resistance of more than 50K rubs high quality polyester fabric.The OEM shall

ISO 9001, BIFMA Level 2 certification & IGBC gold certified manufacturing facility.

Digitally signed by RAJ PAL

SCHEDULE OF QUANTITIES: FURNITURE

S No Item Description Technical Specifications Category/ Area QTY Rate Images for Ref. Only

The overall size of the sofa shall be 1750 L x 790 D x 790 H. Sofa inner frame structure shall be made mainly from the

combination of treated pine wood of 20-25mm thick & neem based plywood sheets. The polyurethane (PU) foam of

density 32 and 40 shall be used in seat constructions and 32 density foam used in back construction along with the

webbing belts. Seat height should be 440mm (+/- 10mm) and seat depth shall be 525mm (+/- 20mm). Each sofa

individual set type shall consist of 4 metal legs of 200 mm height that shall be laser cut and press formed in 2mm thick CGM & GM

18 2 seater sofa CR steel in complaince with IS 513: 2008. The legs shall be formed in V-shape with 125 x 125mm length flanges on its 2 56000 112000

top face and moulded leg bush shall be fixed at its bottom that shall support height adjustment of upto 10mm. To suppor

thte sofa two nos wide flanges of the leg shall be be provided. Legs shall be pretreated through nano ceramic process

that shall be environment friendly to enable powder coating to the thickness of 50-80 microns. The fabric used shall be

450-475 gms per meter having abrasion resistance of more than 50K rubs high quality polyester fabric. The OEM shall

ISO 9001, BIFMA Level 2 certification & IGBC gold certified manufacturing facility.

The overall size of the sofa shall be 850 L x 790 D x 790 H. Sofa inner frame structure shall be made mainly from the

combination of treated pine wood of 20-25mm thick & neem based plywood sheets. The polyurethane (PU) foam of

density 32 and 40 shall be used in seat constructions and 32 density foam used in back construction along with the

webbing belts. Seat height should be 440mm (+/- 10mm) and seat depth shall be 525mm (+/- 20mm). Each sofa

individual set type shall consist of 4 metal legs of 200 mm height that shall be laser cut and press formed in 2mm thick

19 single seater sofa CR steel in complaince with IS 513: 2008. The legs shall be formed in V-shape with 125 x 125mm length flanges on its 17 33000 561000

top face and moulded leg bush shall be fixed at its bottom that shall support height adjustment of upto 10mm. To suppor

thte sofa two nos wide flanges of the leg shall be be provided. Legs shall be pretreated through nano ceramic process

that shall be environment friendly to enable powder coating to the thickness of 50-80 microns. The fabric used shall be

450-475 gms per meter having abrasion resistance of more than 50K rubs high quality polyester fabric. The OEM shall

ISO 9001, BIFMA Level 2 certification & IGBC gold certified manufacturing facility.

The overall size of glass table shall be 1200L x 600W x 425H. The table top shall be made of 8mm thick toughned

glass. The understructure shall be made of 19mm SS round tube. Leg shall be provided ABS shoe to protect from

streched.The OEM shall ISO 9001, BIFMA Level 2 certification & IGBC gold certified manufacturing facility. CGM & GM

20 Center table 15 17000 255000

The overall size of glass table shall be 600L x 600W x 505H. The table top shall be made of 8mm thick toughned glass.

The understructure shall be made of 19mm SS round tube. Leg shall be provided ABS shoe to protect from

streched.The OEM shall ISO 9001, BIFMA Level 2 certification & IGBC gold certified manufacturing facility.

21 Round Table For All 15 13950 209250

Meeting table in size of 3600 x 1200 x 750 (WDH)mm.

The worksurface of the table shall be made up of 25mm thick Pre-laminate particle board as per E1 norms and its edges

duly sealed with 2mm PVC Lipping on automatic machine at visible sides. Two Long sides of the work surface shall be

provided with reverse tapered edge design created by chamfering the board at 45 degree inside for 17mm length &

keeping 8mm straight & then edges sealed with 2mm thick PVC Lipping on automatic machine. Leg: shall be made up of

12 pax Meeting high pressure aluminum die casted 20 degree tapered, number “7” shape & oblong cross section of about 55mm on top,

22 Meeting room 1 80188 80188

Room 45mm at bottom and of 725mm length to get 750mm table height, it shall acts as vertical structural support member,

connected by a horizontal cross beams 50x25x1.6thk (16g) ERW tube & connected to the Aluminium diecast vertical

legs through a high pressure Aluminium diecast 90deg – 02 way connectors. Wire Management: 450mm Aluminium Flip

Up and provision to mount swicthes and sockets on PVC cable dump and Vertical wire entry cover made up of steel

sheets.Understructure shall powder coated upto 40 to 60microns.The OEM shall ISO 9001, BIFMA Level 2 certification &

IGBC gold certified manufacturing facility.

Meeting table in size of 3600 x 1500 x 750 (WDH)mm.

The worksurface of the table shall be made up of 25mm thick Pre-laminate particle board as per E1 norms and its edges

duly sealed with 2mm PVC Lipping on automatic machine at visible sides. Two Long sides of the work surface shall be

provided with reverse tapered edge design created by chamfering the board at 45 degree inside for 17mm length &

keeping 8mm straight & then edges sealed with 2mm thick PVC Lipping on automatic machine. Leg: shall be made up of

12 pax Meeting high pressure aluminum die casted 20 degree tapered, number “7” shape & oblong cross section of about 55mm on top,

23 45mm at bottom and of 725mm length to get 750mm table height, it shall acts as vertical structural support member, Meeting room 1 97678 97678

connected by a horizontal cross beams 50x25x1.6thk (16g) ERW tube & connected to the Aluminium diecast vertical

legs through a high pressure Aluminium diecast 90deg – 02 way connectors. Wire Management: 450mm Aluminium Flip

Up and provision to mount swicthes and sockets on PVC cable dump and Vertical wire entry cover made up of steel

sheets.Understructure shall powder coated upto 40 to 60microns.The OEM shall ISO 9001, BIFMA Level 2 certification &

IGBC gold certified manufacturing facility.

Digitally signed by RAJ PAL

SCHEDULE OF QUANTITIES: FURNITURE

S No Item Description Technical Specifications Category/ Area QTY Rate Images for Ref. Only

Meeting table in size of 3000 x 1500 x 750 (WDH)mm.

The worksurface of the table shall be made up of 25mm thick Pre-laminate particle board as per E1 norms and its edges

duly sealed with 2mm PVC Lipping on automatic machine at visible sides. Two Long sides of the work surface shall be

provided with reverse tapered edge design created by chamfering the board at 45 degree inside for 17mm length &

keeping 8mm straight & then edges sealed with 2mm thick PVC Lipping on automatic machine. Leg: shall be made up of

10 pax Meeting high pressure aluminum die casted 20 degree tapered, number “7” shape & oblong cross section of about 55mm on top,

24 45mm at bottom and of 725mm length to get 750mm table height, it shall acts as vertical structural support member, Meeting room 1 91920 91920

connected by a horizontal cross beams 50x25x1.6thk (16g) ERW tube & connected to the Aluminium diecast vertical

legs through a high pressure Aluminium diecast 90deg – 02 way connectors. Wire Management: 450mm Aluminium Flip

Up and provision to mount swicthes and sockets on PVC cable dump and Vertical wire entry cover made up of steel

sheets.Understructure shall powder coated upto 40 to 60microns.The OEM shall ISO 9001, BIFMA Level 2 certification &

IGBC gold certified manufacturing facility.

Meeting table in size of 6000 x 1500 x 750 (WDH)mm.

The worksurface of the table shall be made up of 25mm thick Pre-laminate particle board as per E1 norms and its edges

duly sealed with 2mm PVC Lipping on automatic machine at visible sides. Two Long sides of the work surface shall be

provided with reverse tapered edge design created by chamfering the board at 45 degree inside for 17mm length &

keeping 8mm straight & then edges sealed with 2mm thick PVC Lipping on automatic machine. Leg: shall be made up of

18 pax Meeting high pressure aluminum die casted 20 degree tapered, number “7” shape & oblong cross section of about 55mm on top, Board meeting

Room 45mm at bottom and of 725mm length to get 750mm table height, it shall acts as vertical structural support member, room

connected by a horizontal cross beams 50x25x1.6thk (16g) ERW tube & connected to the Aluminium diecast vertical

legs through a high pressure Aluminium diecast 90deg – 02 way connectors. Wire Management: 450mm Aluminium Flip

Up and provision to mount swicthes and sockets on PVC cable dump and Vertical wire entry cover made up of steel

sheets.Understructure shall powder coated upto 40 to 60microns.The OEM shall ISO 9001, BIFMA Level 2 certification &

IGBC gold certified manufacturing facility.

Back width shall be : 525mm , Total height : 1000 to 1100 mm, Back height- 550 mm, Seat width :520 mm, Seat depth :

460 mm, Seat height : 460 to 560 mm. Outer back shall be injection moulded with PAGF 30% and Inner with PP,

upholstered with 620 G/Y, 100% elastomer nylon mesh – Abrasion- >100000 rubs. Chair back connected to two

directional adjustable Polypropylene lumbar support for achieving comfortable seating posture to the user. Fabric

REVOLVING upholstery : Seat shall be upholstered with SDR knitted fabric with FR grade passing California technical bulletin

HEAD MAIN 117,Sec E: 2000. Knit mesh fabrics are comprised of evenly spaced openings that create breathable effect, It is light

26 CHAIR CUSHION weight , durable and easy to clean. Synchro tilt mechanism offered in Multi lock feature. Twin Casters 60mm dia with Meeting room 8 29000 232000

SEAT & MESH Nylon material complying with ANSI / BIFMA X 5.1 – 2017 standards. The 660mm PCD (26 inches) five pronged base

fabricated with CR Sheets of 1.2 mm thick. Single swage Class 4 tested -ANSI BIFMA performance standards.

The overall size of Chair shall be width 600 +/-5mm, depth 640 +/-5mm. Total height shall be 995 to 1095 +/-5 mm, Back

Width 425 mm at Top and 500mm at bottom, Seat Width 500 +/-5 mm, Seat Depth 470+/-5 mm and Seat height 470mm

to 570 mm +/-5mm range. Seat shall be made up of foam pre moulded at 55 kg/m3 density. hardness of 25+ 3kgf at

50% deflection conforming to IS 3400. Seat shall be uplhostered with micro fabric 100% polyster 180 GSM abrasion >

50000 cycles. Fire rated fabric confirming to BS EN 1021 (match) should be used. The chair shall be supplied with Mesh

Back rest. The back frame shall be made up of Injection molded PPGF 20%. Adjustable Lumbar Support made up of PU

REVOLVING having size 365 mm x 110 mm x 25mm thick shall be provided for better comfort. The Chair should be provided with Self

27 CHAIR CUSHION Calibrating Multilock Mechanism (Bio Snchyro mechansim) that should adjust the tension of the back sensing weight of Meeting room 60 11680 700778

SEAT & BACK the user. The chair shall be Greenguard certified. The mechanism shall allow 360 degree revolving feature along with

height adjustablility. The chair shall be provided fixed armrest. The mechansim shall possess seat to back recline ratio of

3:7. The Gas Lift used shall be class 4 tested as per ANSI BIFMA standards. Nylon Base shall be provided.Twin castors

50 mm dia with PA6 material complying to ANSI/ BIFMA X 5.1 2017 standards. The base shall be 660 mm PCD (26

inches) five pronged bases made up of PA6, 30% glass filled reinforced with bottom ribbing for additional buttress and

strength.The OEM shall ISO 9001, BIFMA Level 2 certification & IGBC gold certified manufacturing facility.

The overall size of the meeting table is 1200 dia.he top shall be made up of 25mm thick pre laminated partical board

with 2mm PVC edge band. Leg: shall be made up of high pressure aluminum die casted 20 degree tapered, number “7”

shape & oblong cross section of about 55mm on top, 45mm at bottom and of 725mm length to get 750mm table height,

it shall acts as vertical structural support member, connected by a horizontal cross beams 50x25x1.6thk (16g) ERW tube

28 Round table Round Table 4 36711 146844

& connected to the Aluminium diecast vertical legs through a high pressure Aluminium diecast connectors.The OEM

shall ISO 9001, BIFMA Level 2 certification & IGBC gold certified manufacturing facility.

Digitally signed by RAJ PAL

SCHEDULE OF QUANTITIES: FURNITURE

S No Item Description Technical Specifications Category/ Area QTY Rate Images for Ref. Only

The Overall size of the Dinning table shall be 1600 x 900 x 760. Supplying 6-seater dining table whoseLeg: shall be

made up of high pressure aluminum die casted 20 degree tapered, number “7” shape & oblong cross section of about

55mm on top, 45mm at bottom and of 725mm length to get 750mm table height, it shall acts as vertical structural

support member, connected by a horizontal cross beams 50x25x1.6thk (16g) ERW tube & connected to the Aluminium

Dinning table diecast vertical legs through a high pressure Aluminium diecast connectors. Top surface shall be 10mm thick toughened Executive

with chair coloured glass resting on 18mm thick prelaminated particle board E1 norms duly tapered for better aesthetics. The Dinnig table

chairs shall be made up of wooden legs & frame. The back shall be made up of bent ply curved till armrest sides duly

finished. The seat shall be made up of foam upholstered with high quality fabric. The OEM shall ISO 9001, BIFMA Level

2 certification & IGBC gold certified manufacturing facility.

1 Way Compactor

Construction:- All components like front mechanism box, shelvings, clading sheet etc. shall be made out of superior

quality of CRCA sheets. It shall consist of storage units of 450mm deep, movable and bolted to undercarriage that rolls

on the channels firmly embedded to the ground. The size of storage body shall be: width 915 mm, depth 450 mm and a

height of 1980 mm (overall variance +/- 50 mm) including the storage body height with undercarriage The main body

should be rigid knock down construction is made of out of Side /tack/top Panels made up of minimum 0.8mm thick

CRCA steel. Each body block should consists of one single fixed unit, one double mobile one single mobile unit and add

on as per site conditions and each unit should have 5 loading levels formed by 4 nos of adjustable shelves. The storage

body units shall be bolted to the undercarriage. The shelf panel of storage unit should be made of 0.8mm thick CRCA

steel having UDL of 40-50 Kg per shelf. The shelves should be mounted on support brackets & its level should be

adjustable. There should be 4 adjustable shelves per body giving 5 loading levels. The under carriage should be made

30 1 Bay compactor Record room 12 44000 528000

with HR sheet min 2.5 min suitably fabricated using welding to take the loads. The MSU should be running on a

guidetrack of size 28 mm M.S. round with necessary bracing/channel and base plate. Rails should be 25 mm square

bright bar. The OEM shall have IGBC gold rated factory certification. The bodies including shelves and undercarriages

should be given 7 tank antirust surface treatments and finished with powder coating using epoxy polyester powder of 50-

60microns. A centralized locking arrangement should be provided through the locking stiffener mounted onto back of

single last unit so that it gets locked on channels when all the units are brought together. All the' units should be

provided with chrome plated handles. All the MSU should be provided with the features such as mechanical drive with a

handle for mechanically assisted drive mechanism consisting of a series of sprocket and chain mechanism for smooth

movement of the compactor with minimum effort. It should be fitted with safety guard which is to be engaged when

entering the common aisle. This should prevent from operating system when an individual is in the working aisle. The

guide track should be provided with an end stopper to avoid derailment of the units. It should be provided with the label

2 Way Compactor

Construction:- All components like front mechanism box, shelvings, clading sheet etc. shall be made out of superior

quality of CRCA sheets. It shall consist of storage units of 450mm deep, movable and bolted to undercarriage that rolls

on the channels firmly embedded to the ground. The size of storage body shall be: width 915 mm, depth 450 mm and a

height of 1980 mm (overall variance +/- 50 mm) including the storage body height with undercarriage The main body

should be rigid knock down construction is made of out of Side /tack/top Panels made up of minimum 0.8mm thick

CRCA steel. Each body block should consists of one single fixed unit, one double mobile one single mobile unit and add

on as per site conditions and each unit should have 5 loading levels formed by 4 nos of adjustable shelves. The storage

body units shall be bolted to the undercarriage. The shelf panel of storage unit should be made of 0.8mm thick CRCA

steel having UDL of 40-50 Kg per shelf. The shelves should be mounted on support brackets & its level should be

31 2 Bay compactor adjustable. There should be 4 adjustable shelves per body giving 5 loading levels. The under carriage should be made Record room 72 40000 2880000

with HR sheet min 2.5 min suitably fabricated using welding to take the loads. The OEM shall have IGBC gold rated

factory certification. The MSU should be running on a guidetrack of size 28 mm M.S. round with necessary

bracing/channel and base plate. Rails should be 25 mm square bright bar. The bodies including shelves and

undercarriages should be given 7 tank antirust surface treatments and finished with powder coating using epoxy

polyester powder of 50-60microns. A centralized locking arrangement should be provided through the locking stiffener

mounted onto back of single last unit so that it gets locked on channels when all the units are brought together. All the'

units should be provided with chrome plated handles. All the MSU should be provided with the features such as

mechanical drive with a handle for mechanically assisted drive mechanism consisting of a series of sprocket and chain

mechanism for smooth movement of the compactor with minimum effort. It should be fitted with safety guard which is to

be engaged when entering the common aisle. This should prevent from operating system when an individual is in the

working aisle. The guide track should be provided with an end stopper to avoid derailment of the units. It should be

Digitally signed by RAJ PAL

SCHEDULE OF QUANTITIES: FURNITURE

S No Item Description Technical Specifications Category/ Area QTY Rate Images for Ref. Only

The overall size of L-shaped worksatation shall be 1500-1350x600x750/1200h. The table top shall be size of 1500-1350

x 600 with 300mm radius at the user side.The partition based system shall be with main and return spine in 60 mm thick

made by 1.2 mm thick CRCA sheet confirming to IS 513: (2008), IS 13871:1993.Under table top 18mm thick PLP gable

end shall be provided to support the table top. The profile of verticals should be able to slide the tiles thickness of 6 mm.

The verticals shall have multiple slots for carrying the data and power cables and provision for fixing MS brackets Slots

shall be provided at different heights for fixing table top brackets, tiles and shelves. There shall be minimum three slots

at different levels to accommodate raceways at skirting and table top levels. There shall be options of carrying the

cables both above and below the table top as per the requirement. The slot cut out should be made by CNC machines

to avoid sharp edges and burr. There shall be minimum four horizontal members in each frame- top , middle levels and

at the skirting level. The horizontal members shall be made from CRCA sheets formed in “C” shape in hydraulic press.

The CRCA sheets shall be confirmed to IS 513: (2008), IS 13871:1993. The horizontal members shall be fabricated with

welded joints to the vertical which makes the frames sturdy and facilitates carriage of cables at different levels. The

middle cross members shall have minimum two slots for carriage of cable vertically from the floor to the raceways. The

vertical and the cross members shall be CO2 MIG welded to IS 816, ISO 9692- ISO 9692-3. The bottom cross member

Record Room should be elevated by 120 mm from the floor level. All the frames should be fitted with M10 leveling bolts to adjust to

32 ground undulations and capable of adjustment +/- 20 mm. the MS bolt shall be zinc pacified with insert molded in PVC Record room 2 52122 104244

shoes. All frames are fixed with aluminum trims confirming to IS – 733. The top and end trims shall be minimum 1.2 mm

thick extrusions confirming to IS-733:2017 and ISO -2768-2, EN AW 755-2, EN AW 573-3. These trims are finished in

an epoxy powder coating finish. The aluminum trims and MS brackets shall be powder coated. The aluminum trims and

MS brackets undergoes 7 step rust resistance pre treatment process viz degreasing, pickling as per IS standard

conforming to ASTM D 1186, ASTM D 1737, DIN 5156, IS 2360, IS 101, ASTM D 522, 523. ASTM D3451 – 06, -DIN EN

14901 - DIN EN ISO 9227, IS 3618 – 2016. After pre pre-treatment process, the components are NANO coated and

passified for better adhesion of paint as per IS 3618 - 2016. The product shall be bifma level 2 certified. The

components are powder coated with epoxy polyester powder to the thickness of 50-60 microns as per IS 101 and oven

baked at 180 degrees for getting the scratch resistance finish.Product undergoes the following testing process for

durability and functionality, cross cut test for ensuring adhesion of powder coating as per IS standard, Salt spray test

for ensuring the rust resistance. The connectors to the frames should have Aluminum die cast connectors confirming to

IS 742, IS 2600, ADC-12 material confirming to ASTM E 1251-2011, IS 7658-1990 & IS 11035 – 2014, IS 1608 –

2018.Panel Finishes : Finishes of panel above the worktop can be fabric pinup/fabric/laminate + Glass writable marker

board or single finish tile with raceway on main spine. Finishes of main spine panel below the worktop the hollow panel

RECEPTIONS should be made of PLPB tile. Raceway can be provided above/below the worktop.The OEM shall ISO 9001, BIFMA

Reception table

The overall size of the reception table shall be 2400 mm length, 750 mm depth & 1050 mm height. On the front side

both ends shall be provided with groove design strips to enhance the overall look. At the centre of the front side L shape

surface shall be provided fixed up with hinges to paste logo of the department if required. The entire table shall be made

RECEPTION AND up of 25mm / 18mm thick pre laminated particle board of E1 norms. Inside of table a working height shelf should be Receptions

CORIDOR AREA provided or height 750 mm to keep desktop/ laptop and normal working with sitting. the edges of the visible surface shall area

be sealed with 2mm thick PVC lipping on automatic machine. The OEM shall ISO 9001, BIFMA Level 2 certification &

IGBC gold certified manufacturing facility.

Digitally signed by RAJ PAL

SCHEDULE OF QUANTITIES: FURNITURE

S No Item Description Technical Specifications Category/ Area QTY Rate Images for Ref. Only

The worktop height shall be 750 mm & height including partition screens shall be 1100mm. The worktop shall be made

up of 25mm thick pre-laminated particle board of grade E1 low emitting material. The understructure shall be made up of

MS powder coated legs having enhanced look with 08 facestrapezoidal cross section size 52mm x 52mm x 52mm x

26mm with chamfered corners and thickness of 1.6mm. Edges of the leg should not have sharp edges. For safety of

users a radius of R3.20 mm should be provided. The vertical legs shall be connected by horizontal beams with the help

of aluminum die cast connector that joints the legs vertically and horizontally with pipe of cross section 50 x 25 mm x 1.6

mm thickness. The die cast connect size shall be L shaped having angle of 10 degrees for vertical leg side. The Diecast

connector will have same shape as of Trapezoidal vertical leg at one side and another side matching to horizontal cross

section 50x25. The Intermediate leg: Two Verticals of Intermediate leg will have to be with 60x40mm rectangular ERW

tubes and both legs are joined using a beam section of 40x40x1.6mm thk at the top side. The 60x40 verticals to have

Workstation with through “U” notch or through cut out of 40x41mm size at the top side to locate 40x40 cross beam. For ease of wire Workatation

3 drawer pedestal management, a 300 mm length & 142mm breadth flip up cover made up of aluminum having soft closure should be Area

provided. A flip down mechanism enabled cable tray shall be provided below the worktop to mount switches and

sockets. The front fabric screen shall be provided as per workstation size, made up of 18 mm thick prelam particle board

of grade E1 upholstered by fabric, having aluminum extrusion at all three sides having cross section size of 12mm x

5mm & joined at all 4 corners with Zinc mazak5 die cast connector of size 15 L x 15 H x 12mm W. Pedestal - 2D+1F in

size of 400W X 450D X 600Ht. The workstation shall be bifma level 2 certified. The prelaminated particle board of

approved shade confirming to E1 norms. Top & Sides shall be18mm Thk pre laminated particle board. Back panel shall

be 9 mm Thk pre laminated particle board. Edge: All exposed area with 2mm thick PVC edge lipping on automatic

machine. The drawers front & filling shall be provided with sleek finger groove handle less design for a streamlined look.

Finger groove shall be created by providing a reverse tapered profile edge of 6mm straight surface & 12 mm tapered

towards inside at 45 degree & then sealed with minimum 2mm thick PVC lipping on automatic machine. Lock: Regular

lock shall be provided. The OEM shall ISO 9001, BIFMA Level 2 certification & IGBC gold certified manufacturing

a Workstation Size - 900L x 600D x 750H 35 24500 857500

b Workstation Size - 1050L x 600D x 750H 8 26899 215194

c Workstation Size - 1200L x 600D x 750H 66 28315 1868808

d Workstation Size - 1500L x 600D x 750H 96 28000 2688000

Table : The overall size of table shall be 1800L x 750D x 750H. & side storage 900L x 450D x 750H. with Back unit

1200L x 450D x 750H. The worktop shall be made up of 25mm thick PLPB, Modesty Panel shall be 18mm thick PLPB

both E1 norms duly sealed with 2mm pvc edge band. Modesty shall be connected with 3 nos L-shape pressure

aluminium die casted connector of 50 mm width. The understructure shall be made up of MS powder coated legs having

enhanced look trapezoidal cross section size 52mm x 52mm x 52mm x 26mm with chamfered corners and thickness of

1.6mm. Edges of the leg should not have sharp edges. For safety of users a radius of R3.20 mm should be provided.

The Trapezoidal tube shall be connected with die cast connectors at top, leg shoe & levelers at bottom. High pressure

aluminum die cast connectors shall of ADC-12 material confirming to ASTM E 1251-2011, IS 7658-1990 & IS 11035 –

1190. The vertical legs shall be connected by horizontal beams with the help of aluminum die cast connector that joints

the legs vertically and horizontally with pipe of cross section 50 x 25 mm x 1.6 mm thickness. The die cast connect size

shall be L shaped having angle of 10 degrees for vertical leg side. The Diecast connector will have same shape as of

Table with Side Trapezoidal vertical leg at one side and another side matching to horizontal cross section 50x25. Wire Management:

35 and Back 300mm Aluminium Flip Up and provision to mount swicthes and sockets on PVC cable dump and Vertical wire entry MD PS 1 72656 72656

Storage cover. Side Composite Storage (Openable Shutter +2D+1F) Top & Sides : 18mm Thk pre laminated particle board Back

E1 norms: 9mm Thk pre laminated particle board Shutters : 18mm Thk pre laminated particle board Handle. Handless

Finger groove shall be created on top edge of shutter doors by providing a reverse tapered profile edge of 6mm straight

surface & 12 mm tapered towards inside at 45 degree & then sealed with minimum 2mm thick PVC lipping on automatic

machine. Suitable number lock shall be provided. The Back unit overall size shall be 1200 x 450 x 750 (WDH) mm.

Central part shall have two drawers at top & one filling below and shutter storage at either ends Top shall be made up of

18 mm thick pre laminated particle board E1 norms, Back shall be made up of 9 mm thick pre laminated particle board

with 2mm PVC edge lipping, Shutters & drawer front shall be made up of 18 mm thick pre laminated particle board.

Edge: All exposed shall be sealed with 2mm thick PVC edge lipping. The hinged doors top and drawer top shall be

provided with finger groove handle-less design for a streamlined look. Finger groove shall be created by providing a

reverse tapered profile edge of 6mm straight surface & 12 mm tapered towards inside at 45 degree & then sealed with

minimum 2mm thick PVC lipping on automatic machine. Suitable lock shall be provided. The OEM shall ISO 9001,

BIFMA Level 2 certification & IGBC gold certified manufacturing facility.

Digitally signed by RAJ PAL

SCHEDULE OF QUANTITIES: FURNITURE

S No Item Description Technical Specifications Category/ Area QTY Rate Images for Ref. Only

Table : The overall size of table shall be 1650L x 750D x 750H. & side storage 900L x 450D x 750H. with Back unit

1200L x 450D x 750H. The worktop shall be made up of 25mm thick PLPB, Modesty Panel shall be 18mm thick PLPB

both E1 norms duly sealed with 2mm pvc edge band. Modesty shall be connected with 3 nos L-shape pressure

aluminium die casted connector of 50 mm width. The understructure shall be made up of MS powder coated legs having

enhanced look trapezoidal cross section size 52mm x 52mm x 52mm x 26mm with chamfered corners and thickness of

1.6mm. Edges of the leg should not have sharp edges. For safety of users a radius of R3.20 mm should be provided.

The Trapezoidal tube shall be connected with die cast connectors at top, leg shoe & levelers at bottom. High pressure

aluminum die cast connectors shall of ADC-12 material confirming to ASTM E 1251-2011, IS 7658-1990 & IS 11035 –

1190. The vertical legs shall be connected by horizontal beams with the help of aluminum die cast connector that joints

the legs vertically and horizontally with pipe of cross section 50 x 25 mm x 1.6 mm thickness. The die cast connect size

shall be L shaped having angle of 10 degrees for vertical leg side. The Diecast connector will have same shape as of

Table with Side Trapezoidal vertical leg at one side and another side matching to horizontal cross section 50x25. Wire Management:

36 and Back 300mm Aluminium Flip Up and provision to mount swicthes and sockets on PVC cable dump and Vertical wire entry DGM 12 69353 832240

Storage cover. the product shall be bifma level two certified. Side Composite Storage (Openable Shutter +2D+1F) Top & Sides :

18mm Thk pre laminated particle board Back E1 norms: 9mm Thk pre laminated particle board Shutters : 18mm Thk pre

laminated particle board Handle. Handless Finger groove shall be created on top edge of shutter doors by providing a

reverse tapered profile edge of 6mm straight surface & 12 mm tapered towards inside at 45 degree & then sealed with

minimum 2mm thick PVC lipping on automatic machine. Suitable number lock shall be provided. The Back unit overall

size shall be 1200 x 450 x 750 (WDH) mm. Central part shall have two drawers at top & one filling below and shutter

storage at either ends Top shall be made up of 18 mm thick pre laminated particle board E1 norms, Back shall be made

up of 9 mm thick pre laminated particle board with 2mm PVC edge lipping, Shutters & drawer front shall be made up of

18 mm thick pre laminated particle board. Edge: All exposed shall be sealed with 2mm thick PVC edge lipping. The

hinged doors top and drawer top shall be provided with finger groove handle-less design for a streamlined look. Finger

groove shall be created by providing a reverse tapered profile edge of 6mm straight surface & 12 mm tapered towards

inside at 45 degree & then sealed with minimum 2mm thick PVC lipping on automatic machine. Suitable lock shall be

The overall size of Chair shall be width 600 +/-5mm, depth 640 +/-5mm. Total height shall be 995 to 1095 +/-5 mm, Back

Width 425 mm at Top and 500mm at bottom, Seat Width 500 +/-5 mm, Seat Depth 470+/-5 mm and Seat height 470mm

to 570 mm +/-5mm range. Seat shall be made up of foam pre moulded at 55 kg/m3 density. hardness of 25+ 3kgf at

50% deflection conforming to IS 3400. Seat shall be uplhostered with micro fabric 100% polyster 180 GSM abrasion >

50000 cycles. Fire rated fabric confirming to BS EN 1021 (match) should be used. The chair shall be supplied with Mesh

Back rest. The back frame shall be made up of Injection molded PPGF 20%. Adjustable Lumbar Support made up of PU

DGM High back having size 365 mm x 110 mm x 25mm thick shall be provided for better comfort. The Chair should be provided with Self

37 Calibrating Multilock Mechanism (Bio Snchyro mechansim) that should adjust the tension of the back sensing weight of DGM & MD PS 13 11680 151840

the user. The chair shall be Greenguard certified. The mechanism shall allow 360 degree revolving feature along with

height adjustablility. The chair shall be provided fixed armrest. The mechansim shall possess seat to back recline ratio of

3:7. The Gas Lift used shall be class 4 tested as per ANSI BIFMA standards. Nylon Base shall be provided.Twin castors

50 mm dia with PA6 material complying to ANSI/ BIFMA X 5.1 2017 standards. The base shall be 660 mm PCD (26

inches) five pronged bases made up of PA6, 30% glass filled reinforced with bottom ribbing for additional buttress and

strength.The OEM shall ISO 9001, BIFMA Level 2 certification & IGBC gold certified manufacturing facility.

The overall size of Chair shall be height 915 to 1015 +/-5 mm, Back Width 415 mm at Top and 450mm at bottom, Seat

Width 480 +/-5 mm, Seat Depth 440+/-5 mm and Seat height 460mm to 560 mm +/-5mm range. over all chair width

should be 560 +/-5mm and Overall chair depth should be 670 +/-5mm. Seat should be made up of foam pre moulded at

55 kg/m3 density. hardness of 25+ 3kgf at 50% deflection conforming to IS 3400. Seat shall be upholstered with micro

fabric 100% polyster 180 GSM abrasion > 50000 cycles. No flamming or progressive smoldering within one hour of

placement of the cigarettes. The chair shall be greenguard certified. Fire rated fabric confirming to BS EN 1021 (match)

DGM Visitor Mid should be used. The back frame shall be made up of PPGF and the injection molded in black color, armrest also in black

back chair color. The chair shall be supplied with Mesh Back rest. The Chair should be provided with center tilt two position lock

Mechanism. The mechanism shall allow 360 degree revolving feature along with height adjustablility. Fixed arms

connected to seat and back in the same contour. The mechansim shall possess seat to back recline ratio of 1:1. The

Gas Lift used shall be class 4 tested as per ANSI BIFMA standards. Nylon Base in grey color to be provied. Twin

castors 50 mm dia with PA6 material complying to ANSI/ BIFMA X 5.1 2017 standards. the axle pin shall be rust

protected zinc passivated. The base shall be made up of nylon glass filled black color. The OEM shall ISO 9001, BIFMA

Level 2 certification & IGBC gold certified manufacturing facility.

Digitally signed by RAJ PAL

SCHEDULE OF QUANTITIES: FURNITURE

S No Item Description Technical Specifications Category/ Area QTY Rate Images for Ref. Only

The partition based system shall be with main and return spine in 60 mm thick made by 1.2 mm thick CRCA sheet

confirming to IS 513: (2008), IS 13871:1993. The profile of verticals should be able to slide the tiles thickness of 6 mm.

The verticals shall have multiple slots for carrying the data and power cables and provision for fixing MS brackets Slots

shall be provided at different heights for fixing table top brackets, tiles and shelves. There shall be minimum three slots

at different levels to accommodate raceways at skirting and table top levels. There shall be options of carrying the

cables both above and below the table top as per the requirement. The slot cut out should be made by CNC machines

to avoid sharp edges and burr. There shall be minimum four horizontal members in each frame- top , middle levels and

at the skirting level. The horizontal members shall be made from CRCA sheets formed in “C” shape in hydraulic press.

The CRCA sheets shall be confirmed to IS 513: (2008), IS 13871:1993. The horizontal members shall be fabricated with

welded joints to the vertical which makes the frames sturdy and facilitates carriage of cables at different levels. The

middle cross members shall have minimum two slots for carriage of cable vertically from the floor to the raceways. The

vertical and the cross members shall be CO2 MIG welded to IS 816, ISO 9692- ISO 9692-3. The bottom cross member

should be elevated by 120 mm from the floor level. All the frames should be fitted with M10 leveling bolts to adjust to

Cubical Pannel ground undulations and capable of adjustment +/- 20 mm. the MS bolt shall be zinc pacified with insert molded in PVC

Table shoes. All frames are fixed with aluminum trims confirming to IS – 733. The top and end trims shall be minimum 1.2 mm

thick extrusions confirming to IS-733:2017 and ISO -2768-2, EN AW 755-2, EN AW 573-3. These trims are finished in

an epoxy powder coating finish. The aluminum trims and MS brackets shall be powder coated. The aluminum trims and

MS brackets undergoes 7 step rust resistance pre treatment process viz degreasing, pickling as per IS standard

conforming to ASTM D 1186, ASTM D 1737, DIN 5156, IS 2360, IS 101, ASTM D 522, 523. ASTM D3451 – 06, -DIN EN

14901 - DIN EN ISO 9227, IS 3618 – 2016. The workstations shall be bifma level 2 certified. After pre pre-treatment

process, the components are NANO coated and passified for better adhesion of paint as per IS 3618 - 2016. The

components are powder coated with epoxy polyester powder to the thickness of 50-60 microns as per IS 101 and oven

baked at 180 degrees for getting the scratch resistance finish. Product undergoes the following testing process for

durability and functionality, cross cut test for ensuring adhesion of powder coating as per IS standard, Salt spray test

for ensuring the rust resistance. The connectors to the frames should have Aluminum die cast connectors confirming to

IS 742, IS 2600, ADC-12 material confirming to ASTM E 1251-2011, IS 7658-1990 & IS 11035 – 2014, IS 1608 – 2018.

Panel Finishes : Finishes of panel above the worktop can be fabric pinup/fabric/laminate + Glass writable marker board

or single finish tile with raceway on main spine. Finishes of main spine panel below the worktop the hollow panel should

Table : The overall size of table shall be 1500L x 600D x 750H. & side storage 900L x 450D x 750H. with Back unit

1200L x 450D x 750H. The worktop shall be made up of 25mm thick PLPB, Modesty Panel shall be 18mm thick PLPB

both E1 norms duly sealed with 2mm pvc edge band. Modesty shall be connected with 3 nos L-shape pressure

aluminium die casted connector of 50 mm width. The understructure shall be made up of MS powder coated legs

having enhanced look trapezoidal cross section size 52mm x 52mm x 52mm x 26mm with chamfered corners and

thickness of 1.6mm. Edges of the leg should not have sharp edges. For safety of users a radius of R3.20 mm should be

provided. The Trapezoidal tube shall be connected with die cast connectors at top, leg shoe & levelers at bottom. High

pressure aluminum die cast connectors shall of ADC-12 material confirming to ASTM E 1251-2011, IS 7658-1990 & IS

11035 – 1190. The vertical legs shall be connected by horizontal beams with the help of aluminum die cast connector

that joints the legs vertically and horizontally with pipe of cross section 50 x 25 mm x 1.6 mm thickness. The die cast

connect size shall be L shaped having angle of 10 degrees for vertical leg side. The Diecast connector will have same

Cubical Table shape as of Trapezoidal vertical leg at one side and another side matching to horizontal cross section 50x25. Side

40 with Side and Composite Storage (Openable Shutter +2D+1F) Top & Sides : 18mm Thk pre laminated particle board Back E1 norms:

back storage 9mm Thk pre laminated particle board Shutters : 18mm Thk pre laminated particle board Handle. Handless Finger

groove shall be created on top edge of shutter doors by providing a reverse tapered profile edge of 6mm straight surface

& 12 mm tapered towards inside at 45 degree & then sealed with minimum 2mm thick PVC lipping on automatic

machine. Suitable number lock shall be provided. The Back unit overall size shall be 1200 x 450 x 750 (WDH) mm.

Central part shall have two drawers at top & one filling below and shutter storage at either ends. The workstation shall

be bifma level two certified. Top shall be made up of 18 mm thick pre laminated particle board E1 norms, Back shall be

made up of 9 mm thick pre laminated particle board with 2mm PVC edge lipping, Shutters & drawer front shall be made

up of 18 mm thick pre laminated particle board. Edge: All exposed shall be sealed with 2mm thick PVC edge lipping. The

hinged doors top and drawer top shall be provided with finger groove handle-less design for a streamlined look. Finger

groove shall be created by providing a reverse tapered profile edge of 6mm straight surface & 12 mm tapered towards

inside at 45 degree & then sealed with minimum 2mm thick PVC lipping on automatic machine. Suitable lock shall be

L ShapedThe OEMof

Cubicle shall ISO 9001,

overall Size - BIFMA

1500L1Level 2 certification

x 1500L2 x 1200H,& having

IGBC gold certified

table of sizemanufacturing

- 1500 x 600 xfacility.

750 ht with side Office

storage and back storage Assistant

Storage Drawer Pedestal: It shall be of size of 400 x 450 x 600 (WDH) mm made up of 18mm thick Pre-laminate particle

board as per E1 norms and its edges duly sealed with 2mm PVC Lipping on automatic machine at visible sides. Drawer

front & sides shall be made up of 18mm, back 9 mm thick pre laminated particle board of E1 grade with visible edges

sealed with 2mm PVC edge band. The drawer top surface shall be provided with finger groove handle-less design.

Finger groove shall be created by providing a reverse tapered profile edge of 6mm straight surface & 12 mm tapered Workstation

towards inside at 45 degree & then sealed with minimum 2mm thick PVC lipping on automatic machine. Suitable lock area

shall be provided. The axle pin shall be rust protected zinc passivated. The OEM shall ISO 9001, BIFMA Level 2

certification & IGBC gold certified manufacturing facility.

Digitally signed by RAJ PAL

SCHEDULE OF QUANTITIES: FURNITURE

S No Item Description Technical Specifications Category/ Area QTY Rate Images for Ref. Only

The overall size of Chair shall be height 915 to 1015 +/-5 mm, Back Width 415 mm at Top and 450mm at bottom, Seat

Width 480 +/-5 mm, Seat Depth 440+/-5 mm and Seat height 460mm to 560 mm +/-5mm range. over all chair width

should be 560 +/-5mm and Overall chair depth should be 670 +/-5mm. Seat should be made up of foam pre moulded at

55 kg/m3 density. hardness of 25+ 3kgf at 50% deflection conforming to IS 3400. Seat shall be upholstered with micro

fabric 100% polyster 180 GSM abrasion > 50000 cycles. No flamming or progressive smoldering within one hour of

placement of the cigarettes. Fire rated fabric confirming to BS EN 1021 (match) should be used. The back frame shall AGM/AM/MANE

Executive & be made up of PPGF and the injection molded in black color, armrest also in black color. The chair shall be supplied with

office Asst. chair Mesh Back rest. The Chair should be provided with center tilt two position lock Mechanism. The chair shall be

Greenguard certified. The mechanism shall allow 360 degree revolving feature along with height adjustablility. Fixed

arms connected to seat and back in the same contour. The mechansim shall possess seat to back recline ratio of 1:1.

The Gas Lift used shall be class 4 tested as per ANSI BIFMA standards. Nylon Base in grey color to be provied. Twin

castors 50 mm dia with PA6 material complying to ANSI/ BIFMA X 5.1 2017 standards. the axle pin shall be rust

protected zinc passivated. The base shall be made up of nylon glass filled black color. The OEM shall ISO 9001, BIFMA

The 2 certification

1500 certified

x 450 x 1800manufacturing

(WDH) mm. Topfacility.

shall be made up of 18mm thick pre laminated particle

board and Back shall be made up of 9 mm thick pre laminated particle board with 2mm PVC edge lipping, Shutters shall

be made up of 18 mm thick pre laminated particle board. 4 Shutters to be provied for uper & lower compartment. Edge:

Full Height All exposed shall be sealed with 2mm thick PVC edge lipping. Locking faciltity should be provided for safe storage of Workstation

Storage documents. The prelaminated board used shall be of E1 norms. The OEM shall ISO 9001, BIFMA Level 2 certification & area

IGBC gold certified manufacturing facility.

The overall size shall be 1500 x 450 x 1200 (WDH) mm. Top shall be made up of 18mm thick pre laminated particle

board E1 norms and Back shall be made up of 9 mm thick pre laminated particle board with 2mm PVC edge lipping,

Shutters shall be made up of 18 mm thick pre laminated particle board. 4 Shutters to be provied for compartment.

PLANTER Planter Box Shall height of 150mm to keep the planter pot. Edge: All exposed shall be sealed with 2mm thick PVC edge Workstation

45 STORAGE FOR lipping. The hinged doors top shall be provided with finger groove handle-less design for a streamlined look. Finger 15 30000 450000

AISLE groove shall be created by providing a reverse tapered profile edge of 6mm straight surface & 12 mm tapered towards

inside @ 45 degree & then sealed with minimum 2mm thick PVC lipping on automatic machine. Locking faciltity should

be provided for safe storage of documents.The OEM shall ISO 9001, BIFMA Level 2 certification & IGBC gold certified

manufacturing facility.

The overall size shall be 1200 x 450 x 1200 (WDH) mm. Top shall be made up of 18mm thick pre laminated particle

board E1 norms and Back shall be made up of 9 mm thick pre laminated particle board with 2mm PVC edge lipping,

Shutters shall be made up of 18 mm thick pre laminated particle board. 4 Shutters to be provied for compartment.

Planter Box Shall height of 150mm to keep the planter pot. Edge: All exposed shall be sealed with 2mm thick PVC edge

PLANTER lipping. The hinged doors top shall be provided with finger groove handle-less design for a streamlined look. Finger

46 STORAGE FOR groove shall be created by providing a reverse tapered profile edge of 6mm straight surface & 12 mm tapered towards 2 27217 54433

AISLE inside @ 45 degree & then sealed with minimum 2mm thick PVC lipping on automatic machine. Locking faciltity should

be provided for safe storage of documentsThe OEM shall ISO 9001, BIFMA Level 2 certification & IGBC gold certified

manufacturing facility.

The overall size shall be 1050 x 450 x 1200 (WDH) mm. Top shall be made up of 18mm thick pre laminated particle

board E1 norms and Back shall be made up of 9 mm thick pre laminated particle board with 2mm PVC edge lipping,

Shutters shall be made up of 18 mm thick pre laminated particle board. 4 Shutters to be provied for compartment.

Planter Box Shall height of 150mm to keep the planter pot. Edge: All exposed shall be sealed with 2mm thick PVC edge

PLANTER lipping. The hinged doors top shall be provided with finger groove handle-less design for a streamlined look. Finger Workstation

47 STORAGE FOR groove shall be created by providing a reverse tapered profile edge of 6mm straight surface & 12 mm tapered towards 1 23329 23329

AISLE inside @ 45 degree & then sealed with minimum 2mm thick PVC lipping on automatic machine. Locking faciltity should

be provided for safe storage of documentsThe OEM shall ISO 9001, BIFMA Level 2 certification & IGBC gold certified

manufacturing facility.

The overall size of the café table is 1200 dia. The top shall be made up of 18mm Hydroshield material to enable use of

table in cafeteria and water reistant. Leg: shall be made up of high pressure aluminum die casted 20 degree tapered,

number “7” shape & oblong cross section of about 55mm on top, 45mm at bottom and of 725mm length to get 750mm

table height, it shall acts as vertical structural support member, connected by a horizontal cross beams 50x25x1.6thk

CAFETERIA Cafeteria

48 (16g) ERW tube & connected to the Aluminium diecast vertical legs through a high pressure Aluminium diecast 10 32000 320000

connectors.Understructure shall powder coated upto 40 to 60microns. The OEM shall ISO 9001, BIFMA Level 2

certification & IGBC gold certified manufacturing facility.

Digitally signed by RAJ PAL

SCHEDULE OF QUANTITIES: FURNITURE

S No Item Description Technical Specifications Category/ Area QTY Rate Images for Ref. Only

The overall size of chair height shall be 770mm, Depth 640mm and Width shall be 620mm. The lounge chair seating

height shall be 440mm. The chair understructure shall have 4 legs that should be interconnected with each other

through frame. The understructure of the chair shall be made from solid wood i.e properly treated & seasoned kiln dried

CAFETERIA beach wood, finished with clear synthetic PU coating for the best resilence and high durability. The chair understructure Cafeteria

CHAIR should be 1.6mm thickenss swaged tube.The legs shall be in angular design & thicker on the top & thinner on the

bottom side. Understructure shall powder coated upto 40 to 60microns.The OEM shall ISO 9001, BIFMA Level 2

certification & IGBC gold certified manufacturing facility.

TOTAL 28134403

Digitally signed by RAJ PAL

SCHEDULE OF QUANTITIES: GAS SUPPRESSION SYSTEM

S No Description Unit Qty Rate DSR Amount NDSR Amount

Supply, Installation, Testing and Commissioning of 80 ltrs Seamless Cylinder with Valve with all

accessories( Pressure Guage +Low pressure supervisory switch,Low Pressure Connection Tee

Cable, Pneumatic actuator, Manual Actuator, Flexible Discharge Hose, Tee, Check Valve,

Flexible Actuation Hose, Pressure Switch for gas release input, Low Pressure Connection Unit,

Connection kit for End of Line, Elbow), Sinorix FK5112 gas, Electromagnetic Actuator, Discharge

Nozzles Drilled for 360 degree covereage, M.S. Seamless pipes as per ASTM A 106 Gr. B,

schedule 40 with necessary fittings, Manifold for Cylinders , Cylinder MOUNTING WLL CLAMP,

DNE (Don’t Enter Gas released) Sign board, GRE (Gas release Exit) Sign board, Gas Release

Panel, Gas Abbort Switch, Gas Relase Switch, Sounder cum Strobe

A Server Room Nos 1 699506.00 699506.00

Digitally signed by RAJ PAL

SCHEDULE OF QUANTITIES: VESDA

S No Description Unit Qty Rate DSR Amount NDSR Amount

1 Vesda Laser Focus Panel VLF 250 xtralis Nos. 2 252,000 504,000.00

2 Power Supply for above panels Nos. 2 42,500 85,000.00

3 Capillary set Nos 6 14,870 89,220.00

5 25 mm dia 2 mm thickness pipings Lot 2 10,000 20,000.00

6 Electronic Hooter Cum Strobe Nos. 2 1,200 2,400.00

Digitally signed by RAJ PAL

SCHEDULE OF QUANTITIES: RODENT SOLUTIONS

S No Description Unit Qty Rate DSR Amount NDSR Amount

RODENT SOLUTIONS FOR SERVER ROOM

1 Master Console Panel Capable of connecting to 12 Sattleites complete Nos. 2 28,600.00 57,200.00

2 Satellite Detector units complete as required Nos 18 1,680.00 30,240.00

3 Wire Bundles 2 core complete as required and as per specifications. Set 2 5,000.00 10,000.00

4 Bracket Stand complete as required and as per specifications. Nos. 1 4,500.00 4,500.00

Digitally signed by RAJ PAL

SCHEDULE OF QUANTITIES: RODENT & WLD SOLUTIONS

S No Description Unit Qty Rate DSR Amount NDSR Amount

WATER LEAK DETECTION FOR SERVER ROOM

Supply of 4 Zone microprocessor based water leak detection panel with Nos

inbuilt keypad and LED indications of the zones in alarm or fault

2 water leak detection cable Nos 40 2,388.00 95,520.00

3 Electronic hooter Nos 2 1,200.00 2,400.00

Digitally signed by RAJ PAL

SCHEDULE OF QUANTITIES: LANDSCAPE

S NO DSR/MR Description Unit Qty Rate DSR Amount Non DSR Amount

Supply of full soil fill conical shaped planters of specified volume and dimensions in stone finish or

equivalent. planters to be indigenously made by rotational moulding, with homogeneous recyclable,

industrial grade polymer-resin mix, and textured surface. planters should have an integrated water

1 outlet hole & plug, single layered peel-proof construction, light weight, rust proof, uv stabilized, anti-

frost feature without any joints, and easy to clean. planter supplier must give 1 year warranty against

MR any fading or cracking for both indoor and outdoor use. green plant and laying is extra. potting

instructions as per company catalogue.

Supply of double layered translucent backlit cylinderical shaped - hand carfted pattern planters of

volume 40 ltr; approx. dimension 40(h)x18.5(d) in granite/ stone/ solid finish or equivalent. planters

to be indigenously made by rotational moulding, with homogeneous 100% recyclable, industrial

grade polymer-resin mix, with textured surface and stone match finishes. planters to have concealed

shock resistant back lighting system with secured supply wire and an integrated water outlet hole &

plug, peel proof construction, asbestos free, light in weight, without any joints, rust proof, uv

stabilized, anti-frost feature and easy to clean. planter supplier must give 1 year warranty against

any led, fading or cracking for indoor and outdoor use.

3 MR Plantation: Supply and installation of Natural Plant with sand, fertilizer etc. Nos 50.00 1,800.00 90,000.00

Providing & fixing Artificial silk plants with combination 3 or 4 types uniformly

distributed plants as ceiling suspended creepers with necessary wire or hanging

arrangement included. Plants which ultraviolet blocking chemicals are impregnated into

4 MR the materials during the manufacturing process. These chemicals are blended with the plastic Sqm 175.00 6,000.00 1,050,000.00

or PVC parts Installation . Suspended creepers shall be installed in laminated finish trays duly

suspended from the ceiling with twisted rods of size and design as per the detailed drawings

Digitally signed by RAJ PAL

SCHEDULE OF QUANTITIES-SIGNAGE

S No DSR/ MR Description Quantity Unit Rate DSR Amount NDSR Amount

Providing and fixing of signage made out of acrylic sheets of 6mm

thickness. Height of each letter will be 450mm and in width proportionally.

Letters to be fixed on the partition using industrial grade adhesive. Depth

of each letter to be 75mm

Providing and fixing of signage made out of acrylic sheets of 6mm

thickness. Height of each letter will be 250mm and in width proportionally.

Letters to be fixed on the partition using industrial grade adhesive. Depth

of each letter to be 36mm

Providing and fixing of signage for bathroom doors, server room etc made

3 MR out of laser cut SS sheet of 2mm thickness and size 300mmx150mm 55 Nos. 15000.00 825,000.00

powder coated to black

Digitally signed by RAJ PAL