REPAIR/ MAINT OF DG SET, AMF PANEL, FIRE FIGHTING EQPT, SECURITY LIGHT, HIGH MAST DISTRIBUTION SYSTEM, REPLACEMENT OF LT UG CABLE, REPAIRS TO HARD STANDING, FENCING AND OTHER MISC NATURE OF BR EM WORKS AT AFS MADH ISLAND UNDER GE AF THANE

Amount

Maintenance for DG Set 250 KVA, Make - Crompton Greaves, through authorised service agency of OEM , Location :(DG SET -1, Near Library Area AFS Madh) complete all as directed Note :- Spares required for above maint will be measured and paid separately under relevent items involving the following scope of works :- (I) Scope of works :- (a) Check the sample of coolent concentration (b)Check the fan belt for tension and replace if needed. Check exhaust condensate drain and remove any debris or dust.(c ) Check exhaust condensate drain and remove any debris or dust.(d) Examine the charge level of batteryand check for any loose connection and de-scale carbon deposits if any on terminals and application petroleum jelly.(e) Check the air cleaner components and clean the dirt with air pressure.(f) Check and adjust the voltage level of the battery charger.(g) Drain out the water from the container of the bottom of the filter housing and fuel tank.(h) Check the control panel wiring, Instrumentation, contacts fuses, etc.(j) Check the specific gravity of battery every month and condition of Plates once in three months.(k) Check the serviceability of safety controls of Engine.(l) Checking of all electricalconnectons for its proper tightness.(m) Check AVR connections & power cable connections for tightness.(n) Check RPM/Frequency and adjust it.(o) Checking of Load balancing of alternator/AMF panel output(p) Check the condition wire breaded / nonbreaded hoses of engine. (II) In addition to above the following checks will be carried out by contractor on Quartely basis( once in 3 month) :-(a) Replace the fuel filter and oil filter.(b) Clean the crank case breather.(c) Check the radiator hoses. (III) In addition to above the following checks will be carried out by contractor Half yearly (once in six month) :- (a) Greasing of Alternator Bearing(b) Cleaning the diesel tank.(c) Check the installation.(d) Checking of exhaust back pressure.(e) Checking of temperature of exhaust.(f) Check the performance of radiator. (IV) Unit rates quoted shall be inclusive of the following : (a) Checking of all rotary and stationery parts of engine and adjust/repair the defects as required for satisfactory running of DG set.(b) Cleaning and refitting the air cleaner.(c) Cleaning of fuel filter assembly and replacement of filter element along with rubber 'O' ring.(d) Replacement of 'V' belt for driving radiator fan/ water Pump/Battery charger alternator with proper adjustment. Repair to nozzle by replacement plunger & spring valves. Replacement of high pressure stainless steel tubing not less than 1 m length from FIP to nozzle including Benjoo bolts, copper washer etc. Replacement of upper gasket kit.(e) Renewal of oil filter elements including checking of serviceability of lubricants oil pump and repair where necessary for proper oil pressure.(f) Drain out the lub oil and refill new oil after proper cleaning.(g) Checking and adjustment of tappet clearance. Note :- (i) In case of any breakdown service engineer shall attend the break down immediately and make the DG Set Serviceable within 24 working hrs. (ii) Repair, if any must be carried by Contractor through authorised workshop of original manufacturer and Payment will be made to the contractor on Produce of Original Manufacturer's Bills/vouchers.

Ditto all as per item No -1 here-in-before but for 125 KVA DG Sets Make:- Kirloskar ( Power House DG -1) complete all as directed by Engineer in-Charge.

Ditto all as per item No -1 here-in-before but for 125 KVA DG Sets Make:- Kirloskar ( Power House DG-2) complete all as directed by Engineer in-Charge.

Ditto all as per item No -1 here-in-before but for 82.5 KVA DG Sets Make:- Kirloskar ( AFNET SUB station DG -1) complete all as directed by Engineer in-Charge.

Ditto all as per item No -1 here-in-before but for 82.5 KVA DG Sets Make:- Kirloskar ( AFNET SUB station DG-2) complete all as directed by Engineer in-Charge.

Ditto all as per item No -1 here-in-before but for 62.5 KVA DG Set Make:-Crompton Greaves, ( Near SMC Hall station DG -1 ) complete all as directed by Engineer in-Charge.

M&L for Draining out the old sludgs oil from the DG set and replace with new oil as recommended by Mfg complete all as directed by Engineer in-Charge.NOTE : Draining out of Oil shall be done twice in year each time reffiling/Top up )

Supply and fixing for Industrial Battery of 12 Volt,180 AH capacity suitable for 82.5 to 250 KVA DG Sets heavy duty, 25 plates includidng removing existing unserviceable battery from existing places and cleaning of battery terminals and clamps properly and refixed and reconnected complete all as directed by Engineer in-Charge.

Servicing of AMF Panel suitable for 62.5 KVA DG Set to 250 KVA DG Set including cleaning properly with blower, checking of control wiring , replacement of burnt out / damaged wiring connections, calibration of control relay, replacement of control fuses / MCBs all as directed by Engineer in-Charge. NOTE :- Spare parts shall be measured and paid seperately in respective item of this schedule if required as Supply only.

Supply only for LED type Indicator indication lamps R,Y,B) complete all as directed by Engineer in-Charge.

Supply only for Push Buttons with element complete all as directed by by Engineer in-Charge. Make : L&T or Telimechanic

Supply only for Control relay 9/11 pin 12 /24 volt DC of suitable for 62.5 KVA to 125 KVA DG Set complete all as directed by Engineer in-Charge. .

Supply only for CT of ratio upto 150 / 5 10 VA burdan complete all as directed by Engineer in-Charge.Make:- AE/NIPPON

Supply only for HRC fuse 200 Amp complete all as directed by Engineer in-Charge. . Make : L&T/SEIMENS

Supply only for PVC insulated & unsheathed singal core multi strandred copper cable of size 4 sq mm for control wiring complete all as directed by Engineer in-Charge.

Supply only for PVC insulated & unsheathed singal core multi strandred copper cable of size 2.5 sq mm for control wiring complete all as directed .by Engineer in-Charge.

Supply only for PVC insulated & unsheathed singal core multi strandred copper cable of size 1.5 sq mm for control wiring complete all as directed by Engineer in-Charge.

Material and Labour in repairs of Temperature gauge complete all as directed by Engineer in-Charge.

Supply only for Oil Pressure Guage 0-10 Bar complete all as directed by Engineer in-Charge.

Supply only for Digital Frequency meter complete all as directed by Engineer in-Charge.

Supply only for DC Volt meter 0 to 20 volt complete all as directed by Engineer in-Charge.

Supply only for DC Ammeter 0 to 20 Amp complete all as directed by Engineer in-Charge.

Supply only for Excitation coil for 250 KVA DG set complete all as directed by Engineer in-Charge.

Supply only for AVR card for 125 KVA DG set complete all as directed by Engineer in-Charge.

Supply only for AVR card for 82.5 KVA DG setcomplete all as directed by Engineer in-Charge.

Supply only for AVR card for 62.5 KVA DG set complete all as directed by Engineer in-Charge.

Material and Labour for servicing of Turbo charger including Replacemnt of Turbo charger kit for capacity 250KVA /125 KVA/82.5KVA/62.5KVA complete all as directed by Engineer in-Charge.

Material and Labour in Servicing of Self Starter 24 Volt DC for 250 KVA DG Set, dissmantling complete,& replacement of solenoid field coils. cleaning the cummutator strips including replacing the bearing, bends pinion re-assembling, connecting and testing complete all as directed by Engineer in-Charge.

Ditto all as per item No 29 here-in- before but for capacity 125 KVA DG set complete all as directed by Engineer in-Charge.

Ditto all as per item No 29 here-in- before but for capacity 82.5 to 62.5 KVA DG set complete all as directed by Engineer in-Charge.

Material and Labour in repairs of self starter 12 volt DC for 62.5 to 82.5 KVA DG set including all accessories complete all as directed by Engineer in-Charge.

Material and Labour for in repairs of Feed Pump for Aquastic DG set for capacity 62.5 to 82.5 KVA complete all as directed by Engineer in-Charge.Make -Kirloskar

Dis-connecting the alternator from the engine of capacity 250 KVA by removing the coupling & outgoing cable transporting the alternator to authorized maintenance service center for repairsCleaning the armature, applying one coat of varnish and heating and assembling the alternator at workshop and testing at NO load, transporting the same to the site , re-connecting the alternator to the engine after proper alignment including testing and commissioning complete all as directed by Engineer in-Charge.

Ditto all as per item No 34 here-in- before but for 125/ 82.5 KVA DG Sets complete all as directed by Engineer in-Charge.

Draining out the Water from engine of capacity 250KVA the radiator , dis-mantling the leaking radiator assembly from the engine body, transporting to workshop, cutting the bottom chambers, repairing the damaged pipes, brazing the leaking portions ,descaling / clearing all the blocked pipes including repairing the fins, brazing the bottom chambers, testing the radiator for leakages, transporting the same to the site and re-fixing and testing complete all as spd and directed by Engineer in-Charge.

Ditto all as per item No 36 here-in- before but for 125 / 82.5 KVA DG Set complete all as directed by Engineer in-Charge.

Material and Labour in taking down carefully Old rusted silencer & exhaust pipe from engine scraping & cleaning in side & out side applying one coat of zink primer for out side silencer pipe & providing self adjestive Asbasto Rope 12 mm dia from engine to exhaust pipe and painting with 2 coat of syenthetic enameled paint for expose portation of exhaust, complete all as directed by Engineer in-Charge.

Material and Labour scraping the peeled paint of DG set, preparing the surfaces, cleaning the dust and dirt etc of (alternator and engine) applying 2 coats of synthetic enamel paint of approved shade and writing of MES/SM No on the set all as directed of capacity 250/125/82.5/62.5 KVA complete all as directed by Engineer in-Charge.

Supply olny solenoid Switch 12 Volt DC complete all as directed by Engineer in-Charge.. Make: Kirloskar

Supply only Battery terminal Heavy duty made of brass with nut and bolt including washers suitable for 12 volt DC battary complete all as directed by Engineer in-Charge..

Supply only Radiator Hose pipe as per existing set for 62.4/82.5 KVA complete all as directed by Engineer in-Charge.

Supply only Door hinges assembly for Aquastic DG set complete all as directed by Engineer in-Charge.

Supply only Heavy duty Automatic electronic battery charger suitable for 12/24 Volt DC complete all as directed by Engineer in-Charge.

Supply only Ignition Switch for capacity up to 250,125,82.5 KVA DG set complete all as directed by Engineer in-Charge.

Supply only solenoid Switch 24 Volt DC for 125/250 KVA DG Set as per existing complete all as directed by Engineer in-Charge.

Supply only Coolant premix as manufafacture recommendations and required for top up for Accostic DG set complete all as directed by Engineer in-Charge.

Supply only refilling of distilled water for top up battary 12 volt DC complete all as directed by Engineer in-Charge.

Supply only Air Filter inside & out side for capacity 250 KVA DG Set complete all as directed by Engineer in-Charge.

Supply only Primary Fuel Filter for capacity 250 KVA DG set complete all as directed by Engineer in-Charge.

Supply only Secondray Fuel Filter for capacity 250 KVA DG set complete all as directed by Engineer in-Charge.

Supply only Lubricating Oil Filter for capacity 250 KVA DG set complete all as directed by Engineer in-Charge.

Supply only Fuel pipes with benjo bolt and washers.For capacity 250 KVA DG set complete all as directed by Engineer in-Charge.

Supply ony V- Belt as per existing size for capacity 250 KV DG set complete all as directed by Engineer in-Charge.

Supply only Air Filter inside & out side for capacity up to 125 KVA DG set complete all as directed by Engineer in-Charge.

Supply only Primary Fuel Filter for capacity up to 125 KVA DG set complete all as directed by Engineer in-Charge.

Supply only Lubricating Oil Filter for capacity up to 125 KVA DG set complete all as directed by Engineer in-Charge.

Supply only Primary Fuel Filter for capacity for 62.5/82.5 KVA DG set complete all as directed by Engineer in-Charge.

Supply only Secondary fuel filter for capacity for 62.5/82.5 KVA DG set complete all as directed by Engineer in-Charge.

Supply only lubricating Oil Filter for capacity 62.5/82.5 KVA DG set complete all as directed by Engineer in-Charge.

Supply only super by pass oil filter for 125 KVA DG set complete all as directed by Engineer in-Charge.

Supply only Fuel pipes for capacity up to 125 KVA DG set complete all as directed by Engineer in-Charge.

Supply only Vee Belt as per existing size for capacity up to 125 KVA DG set complete all as directed by Engineer in-Charge.

Supply only fuel governing controler for 250 KVA DG set complete all as directed by Engineer in-Charge.

Supply only Coolant hose set suitable for 250 KVA DG set complete all as directed by Engineer in-Charge.

Supply only Coolant hose set suitable for 125 KVA DG set complete all as directed by Engineer in-Charge.

Supply only Coolant hose set suitable for 82.5 KVA DG set complete all as directed by Engineer in-Charge.

Supply only Coolant hose set suitable for 62.5 KVA DG set complete all as directed by Engineer in-Charge.

Supply only Fuel hose set suitable for 250 KVA DG set complete all as directed by Engineer in-Charge.

Supply only Fuel hose set suitable for 82.5 KVA DG set complete all as directed by Engineer in-Charge.

Supply only Fuel hose set suitable for 62.5 KVA DG set complete all as directed by Engineer in-Charge.

Dismantling existing defective earthing PCC chamber and RCC cover and providing new PCC chamber in PCC 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) and precast RCC 1:2:4 type B-1 cover, 60mm thick reinforced with 8mm tor steel bars @ 75 mm c/c both ways, with MS 12 mm dia bar lifting handle complete all as specified and directed by Engineer in-Charge.

M&L in repairs for Earth continuity conductor or main earthing lead fixed to wall on batten/saddles or recess or chases or burried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc of size 4 mm GI Wire complete all as specified and directed by Engineer in-Charge.

Taking down old GI strip/Copper Strip of any type and size complete all specified and directed by Engineer in-Charge.

M&L for Earth continuity conductor or main earthing lead fixed to wall on batten/saddles or recess or chases or burried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc of size 32x6mm GI Strip complete all as specified and directed by Engineer in-Charge.

M&L for Earth continuity conductor or main earthing lead fixed to wall on batten/saddles or recess or chases or burried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc of size 25x3 mm Aluminium Strip complete all as specified and directed by Engineer in-Charge.

M&L for Earth continuity conductor or main earthing lead fixed to wall on batten/saddles or recess or chases or burried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc of size 32 x 6mm copper Strip complete all as specified and directed by Engineer in-Charge.

M&L for Earth continuity conductor or main earthing lead fixed to wall on batten/saddles or recess or chases or burried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc of size 20 x 3 mm Copper Strip complete all as specified and directed by Engineer in-Charge.

Taking down steel tubing of any grade and size, laid under ground or fixed on wall/floor etc complete all as specified and directed by Engineer in-Charge.

M&L for GI tubing, Medium grade, fixed on wall/pole/floor/ceiling of the following sizes complete all as specified and directed by Engineer in-Charge.of the following dia:-

(a) 25 mm bore

(b) 20 mm bore

(c )15mm bore

Supply and fix in repairs Test point terminal block made up of gunmetal or phosphorus bronze 75mmx75mmx25mm drilled and screws including 8mm dia 25mm long hex head screws and connecting to earth strip acomplete all as specified and directed by Engineer in-Charge.

S&F in Replacement of 25 mm bore gun - metal glove or gate Valves,with iron Wheel head,Screwed both ends for iron pipe and fixed for GI pipe including taking out unservicable gate valve from existing pipe line complete all as specified and directed by Engineer in-Charge.

M & L for maintenance free chemical Gel based earthing, Pipe in Pipe type having 80 mm dia 3 mtr long GI pipe(Wall thickness of 3.2 mm) and 7.50 m long GI earthing lead of size 4 sqmm with 60 Kg ENNOV back fill compound , Model No ELE-380-GIPP of INNOV Infra Solution Ltd including necessary excavation and earth work in any type of soil, perforated watering pipe, funnel with wire mesh, earth lead protection pipe light grade, PCC Chamber 1: 3 :6 type C1 ( for even finish on both the faces ) and RCC cover 1:2:4 type B1, 550 x 550 x 50 mm thick with 8 mm dia TMT bars 150 mm c/c both ways with 2 Nos of handles of 10 mm dia all as required at site including testing on completion and taking down of old earthing all as directed by Engineer in-Charge. Note : (1) 7.50 RM GI earth lead including GI pipe light grade is deemed to be included in the quoted rates, beyond 7.50 RM shall be measured and paid separately. (2) Earth resistance of earth pit should be less than 1.0 Ohms on testing after completion. If the desired earth resistance is not obtained the earthing will be redone at no extra cost.

M & L for Earth recharger/Earth resistance reducing compound of 6 KG per buckets comprising of ion and catalyser for reduction of earth resistance as well as retaining moisture in the earth pit with certified( ERDA, NABL, ROHS, IS3043, IEEE IS RULES) and without corroding the earth pit material suitable for all type of earth pit all as specified and as directed by Engineer in-Charge. Note-(a) Percentage reduction of earth resistance should be min 70 Percentage (b) Earth resistance value should be retain atleast 1.5 years. (c) contractor will submit earth resistance value before and after utilization of material.

M&L for Brazing of copper strip joints for copper strips of any size complete all as specified and as directed at site by Engineer in-Charge.

Supply and fix in repairs for the following items to be incorporated in repairs to earthings as per direted by Engineer-in-Charge.of the following:-

(a) Charcoal

(b) Common Salt

(c ) Funnel with wire Mesh

M&L for testing and measuring the earth resistance value of the existing earthings / Down conductor / air terminal after disconnecting the earth continuity conductor from the test point , applying secondary voltage across the terminals, maintaining proper record of the measurement in presence of the users rep, MES rep, submitting the test records, pouring saline water in the earth pit to achieve low earth resistance, observing the same complete all as directed at site by Engineer-in-Charge. Note:1. Earthings within the station premises shall be checked for proper functioning subject to a period of atleast once a month or in case of poor earth value intimated by user, whichever earlier. 2. Materials and earth work for renovation of earthing shall be measured and paid separately under respective item of Sch A 4. Rates quoted shall be deemed to include the cost of brazing / fixing of earth strip upto test terminal as required at site.

Supply and fix in repairs Test point Air termination, single pointed, copper rod 12 mm dia and 300 mm long complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repairs Test point Air termination, single pointed, Aluminium Rod 12 mm dia and 300 mm long complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repairs to following items to be incorporated in repairs to lightening protection system under trench/ground/floor complete all as specified and directed by Engineer-in-Charge. Of the following dia:-

GI pipe 15 mm dia medium grade

GI pipe 40 mm dia light grade for earth lead protection pipe

GI pipe 15 mm dia for light grade earth lead protection pipe

GI Pipe 40 mm dia medium grade 3 Mtr long for support to Air Termination including necessary Stay wire 10 mm dia with one side dead plug drilled with hole of 12 mm dia complete all as specified and directed

Porcelain insulator with nut bolt and washer suitable for fixing copper/gi/aluminium strip on wall or ceiling

Epoxy insulator 100 mm dia conical shape

M&L for PCC 1 : 3 : 6 type C1 with 20 mm stone aggregate for foundtation / concrete blocks / earthing chamber / chamber cover set in cement mortar 1:4 complete all as directed by Engineer-in-Charge.

Supply and fix sheet steel enclosure for test terminal block of size 150x150 mm made out of 2 mm thick dully Powder Coated CRCA sheet for fixing test terminal block all as directed by Engineer-in-Charge.

Testing of earth resistance of the existing earthing by using earth tester obtaining required test result and submit the report all as specified and directed by Engineer-in-Charge. Note : Earth tester required for testing of resistance shall be included in quoted rates.

M&L in repairs fire alarm system conventional 4 zone FAP control panel complying completeall as spd and directed by Engineer-in-Charge.

M&L in repairs fire alarm system conventional 16 zone FAP control panel complying complete all as specified and directed by Engineer-in-Charge.

M&L in repairs MCP conventional ABS complete all as spd and directed by Engineer-in-Charge.

M&L in repairs Electronic Hooter 24 Volts DC complete all as spd and directed by Engineer-in-Charge.

M&L in repairs optical smoke detector complete all as spd and directed by Engineer-in-Charge.

Supply and fixing PVC insulated heavy duty armoured copper conductor of size 2x1.5 sqmm cable for fire alarm complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches n. exc. 1.5 M in width and 1.5 M in deep for laying of pipes and getting out in Soft / loose soil complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches n. exc. 1.5 M in width and 1.5 M in deep for laying of pipes and getting out in hard /dense soil complete all as specified and directed by Engineer-in-Charge.

Returning, filling in, including spreading, leveling, watering and well ramming in layers n. exc. 25 cmcomplete all as specified and directed by Engineer-in-Charge.

Removing excavated material n. exc. 50 M away, depositing as directed at level n. exc. 1.5 M above starting point complete all as specified and directed by Engineer-in-Charge..

Supply and spreading in trenches clear dry sand for cable protection and punning down gently 10 cm below the cable and 15 cm above the cable all as specified and directed by Engineer-in-Charge.Note :- Punning thickness only measured.

Taking out old unreinforced precast concrete cable coverclass LV type1 flat size 250x150x40 mm during excavation of trenches complete all as specified and directed by Engineer-in-Charge.

S&F unreinforced precast concrete cable cover factory made embossed the mark “LT CABLE” class LV type1 flat size 250x150x40 mm during excation of trenches all as specified and directed by Engineer-in-Charge.

Taking down GI pipe laying in trenches for UG cable protection of any sizes pipe complete all as specified and as diercted by Engineer-in-Charge.

Supply and lay in trenches / along the wall / floor pipes GI light grade of size 80 mm with and including all fittings and accessories complete all as specified and and directed for cable protection complete all as specified and directed by Engineer-in-Charge.

Supply and lay in trenches / along the wall / floor pipes GI light grade of size 40 mm with and including all fittings and accessories for cable protection complete all as specified and directed by Engineer-in-Charge.

Taking down any sizes of of LT UG cable XLPE with aluminum conductor multistranded , PVC insulated and PVC sheeted heavy duty 1100 Volts grade under ground cable complete all as specified and as directed by Engineer-in-Charge.

Supply and lay cable XLPE Insulated armored, heavy duty electric power cables (heavy duty) 1100 Volts grade cross sectional area with stranded aluminium conductor of size 10 sq mm 2 Core complete all as specified and directed by Engineer-in-Charge.

Supply and lay cable XLPE Insulated armored, heavy duty electric power cables (heavy duty) 1100 Volts grade cross sectional area with stranded aluminium conductor of size 10 sq mm 4 Core complete all as specified and directed by Engineer-in-Charge.

Supply and lay of LT UG cable XLPE with aluminum conductor multistranded 1100 volts grade in armored, heavy duty electric power cables (heavy duty) 1100 Volts grade cross sectional area with stranded aluminium conductor of size 16 sq mm 4 Core complete all as specified and directed by Engineer-in-Charge.

Supply and lay of LT UG cable XLPE with aluminum conductor multistranded 1100 volts grade in armored, heavy duty electric power cables (heavy duty) 1100 Volts grade cross sectional area with stranded aluminium conductor of size 25 sq mm 4 Core complete all as specified and directed by Engineer-in-Charge.

Supply and lay of LT UG cable XLPE with aluminum conductor multistranded 1100 volts grade in armored, heavy duty electric power cables with stranded aluminium conductor, 1100 volts grade, cross-sectional area of size 35 sq mm 3.5 Core complete all as specified and directed by Engineer-in-Charge.

Supply and lay of LT UG cable XLPE with aluminum conductor multistranded 1100 volts grade in armored, heavy duty electric power cables with stranded aluminium conductor, 1100 volts grade, cross-sectional area of size 95 sq mm 3.5 Core complete all as specified and directed by Engineer-in-Charge.

Supply and lay of LT UG cable XLPE with aluminum conductor multistranded 1100 volts grade in armored, heavy duty electric power cables with stranded aluminium conductor, 1100 volts grade, cross-sectional area of size 70 sq mm 3.5 Core complete all as specified and directed by Engineer-in-Charge.

S&F copper cable flexible PVC insulated 3 x 2.5 sqmm single core along with earth wire in PVC conduit from FRP box to flood light/street light fitting ,including aluminium flat clamp 25 X 4 mm with suitable nuts,bolts and washers etc all as specified and directed by Engineer-in-Charge.

S&F copper cable PVC round sheathed (flexible) industrial cable 3 x 10.0 sqmm single core along with earth wire for high mast lights maintenance all as specified and directed by Engineer-in-Charge.

S & F Rigid non-metallic concealed PVC conduit 20 mm dia inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc.complete all as specified and as directed by Engineer-in-Charge.

Taking down any type any breaking capacity MCCB complete all as specified and as directed by Engineer-in-Charge.

S&F Cable jointing kit for 1100V (Earthed) grade cable for straight through joint complete with jointing material and accessories suitable for 3.5 core XLPE armoured aluminium conductor cable of size 50 to 95 sqmm complete all as specified and directed by Engineer-in-Charge.

M&L for cutting existing road/hard standing not exc 50x60 cm in wide & depth getting out excavated material for laying GI tube , for passing through LT cable, returning filling & well rammaing watering finish suraface 10 cm from top using PCC 1:1.5:3; including removal of surplus soil complete all as specified and directed by Engineer-in-Charge.

M & L for maintenance free chemical Gel based earthing, Pipe in Pipe type having 80 mm dia 3 mtr long GI pipe(Wall thickness of 3.2 mm) and 7.50 m long GI strip earthing electrode of size 25 x 4 mm with 60 Kg ENNOV back fill compound , Model No ELE-380-GIPP of INNOV Infra Solution Ltd or equivalent including necessary excavation and earth work in any type of soil, perforated watering pipe, funnel with wire mesh, earth lead protection pipe light grade, PCC Chamber 1: 3 :6 type C1 ( for even finish on both the faces ) and RCC cover 1:2:4 type B1, 550 x 550 x 50 mm thick with 8 mm dia TMT bars 150 mm c/c both ways with 2 Nos of handles of 10 mm dia all as required at site including testing on completion and taking down of old earthing all as directed by Engineer-in-Charge. Note : (1) 7.50 RM GI earth strip including GI pipe light grade is deemed to be included in the quoted rates, beyond 7.50 RM shall be measured and paid separately. (2) Earth resistance of earth pit should be less than 1.0 Ohms on testing after completion. If the desired earth resistance is not obtained the earthing will be redone at no extra cost.

M & L in repairs for Copper Strip of size 20 x3 mm and including taking out unserviceable Copper strip complete all as specified and directed by Engineer-in-Charge.

Demolition of Cement concrete in ground floor and paving n.exc 15 cm thickness (below or above) ground level including removal all as specified and directedby Engineer-in-Charge.

S & F in replacement sheet metal enclosure for double door DB made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted TP & N 4 ways, 415 Volts, ISI marked 200 amps bus bar stove enameled dust and vermin proof, IP42 suitable for incorporation MCBs and isolators etc including taking down unserviceable old DB any type including MCB etc and including making good disturbed surfaces of walls as necessaty complete all as specified and directed by Engineer-in-Charge.

S & F in replacement sheet metal enclosure for double door DB made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted TP & N 8 ways, 415 Volts, ISI marked 200 amps bus bar stove enameled dust and vermin proof, IP42 suitable for incorporation MCBs and isolators etc including taking down unserviceable old DB any type including MCB etc and including making good disturbed surfaces of walls as necessaty complete all as specified and directed by Engineer-in-Charge.

M&L for PCC (1:3:6) type C2 (using 20 mm graded stone aggregate as in sub base to floor 100 mm thick finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

S & F in replacement MCB ‘B’ series type suitable for 415 volts, 10 KA, AC supply 40 to 100 Amps, triple pole and neutral (TPN) with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer-in-Charge.

S & F in replacement MCB ‘B’ series type suitable for 240 volts, AC supply 6 to 32 Amps, S P & N with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer-in-Charge.

S & F in replacement MCB ‘B’ series type suitable for 240 volts,10 KA, AC supply 6 to 32 Amps , single pole (SP) with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer-in-Charge.

S & F in replacement MCCB 415 volts grade with adjustable short circuit and over load of following rating all as specified and directed by Engineer-in-Charge.of the following:-

63 Amps, 16 KA, 3 Pole

100 Amps, 16 KA, 3 Pole

125 Amps, 16 KA, 3Pole

160 Amps, 36 KA, 3 Pole

200 Amps, 36KA, 3 Pole

Supply & Fix in replacement LED flood light fitting 210 Watts , 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection with impact and corrosion resistant ,Pressure die cast aluminium housing, heat resistant toughened glass with frame, uniform distribution ,including fixing arrangments with angle iron and suitable nut,bolt,washer etc on wall /on pole complete all as specified and as directed by Engineer-in-Charge.

M&L for MS chequered plates in replacement of not less than 6 mm thick of sizes Fe 410-W (Gde E- 250) Quality 'A' incl cutting , welding of strip on the edges for proper fixing and provn of handles for lifting & fixing arrangement as shown & directed.incl taking out the old & unserviceble chequered plates.including one coat of primer & 2 coats of synthetic enamelled paint of approved colour all as directed by Engineer-in-Charge.

Material and Labour for repairing of LT Panel of not exc of sizes 2.5 Mtr x 2 Mtr x 0.80 Mtr doors/shuttering to welding and bracing of hinges, tinkering, and replace worn out rusted unserviceable doors/compartment shutters front sides and back side lock system including replace worn out rubber gaskets/feeding of compartment doors/shutters, decorbonising of all cable terminals, Busbars (R,Y,B &N) aluminium/copper cleaning inside of panel housing with help of air belower heavy duty complete all as specified and directed by Engineer-in-Charge.

Material and Labour for repairing of LT Panel of not exc of sizes 2 Mtr x 1.5 Mtr x 0.80 Mtr doors/shuttering to welding and bracing of hinges, tinkering, and replace worn out rusted unserviceable doors/compartment shutters front sides and back side lock system including replace worn out rubber gaskets/feeding of compartment doors/shutters, decorbonising of all cable terminals, Busbars (R,Y,B &N) aluminium/copper cleaning inside of panel housing with help of air belower heavy duty complete all as specified and directed by Engineer-in-Charge.

Material and Labour for repairing of feeder pillar box of not exc of sizes 2 Mtr x 1.5 Mtr x 0.80 Mtr doors/shuttering to welding and bracing of hinges, tinkering, and replace worn out rusted unserviceable doors/compartment shutters front sides and back side lock system including replace worn out rubber gaskets/feeding of compartment doors/shutters, decorbonising of all cable terminals, Busbars (R,Y,B &N) aluminium/copper cleaning inside of panel housing with help of air belower heavy duty complete all as specified and directed by Engineer-in-Charge.

S& F in repair LED indication lamp for indication of (R,Y,B) 230 Volts including connections and taking out unserviceable indication Lamp complete all as specified and directed by Engineer-in-Charge.

S&F in repair Volt meter 0-500 Volt digital type including connections and taking out unserviceable Volt meter complete all as specified and directed by Engineer-in-Charge.

S&F in repair Ampere meter 0-400Amps digital type including connections and taking out unserviceable Ampere meter complete all as specified and directed by Engineer-in-Charge.

S&F in repairs of epoxy insulators suitable to fixing of earth conducors including all fixing accessories saddles. screws, Nut and bolts complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repairs/Replacement of of the undermentioned items to be incorporated in street light fittings including taking down street light from pole and refixing it on pole after replacement of driver complete all as specified and directed by Engineer-in-Charge.of the followng:-

LED Driver for 1 x 60 watt LED street light complete all as specified and directed by Engineer-in-Charge. Make -Crompton/Bajaj/Havells or Equivalent.

LED Driver for 1 x 90 watt LED street light complete of make -Crompton/Bajaj/Havells or Equivalent.

LED Driver for 1 x100 watt LED flood light complete of make -Crompton/Bajaj/Havells or Equivalent.

LED Driver for 1 x200 watt LED flood light complete of make -Crompton/Bajaj/Havells or Equivalent.

S & F in replacement street light timer, single phase for 8 KW light load comprising of nature switch, contactor and MCB housed in a pole mountable enclosure complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement LED street light fitting 90 Watt 230 V, surge protection 10 KVA, AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.& Supply and fixing to wall / on pole including fixing arrangement with suitable galvanized iron pipe 35 mm bore “light grade” brackets 1 mtr length bent to shape to obtained required shape including clamps, nuts / bots / washers etc connecting with suitable flexible copper wire of size 23/0.0076 complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement LED street light fitting 60 Watt 230 V, surge protection 10 KVA, AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.& Supply and fixing to wall / on pole including fixing arrangement with suitable galvanized iron pipe 35 mm bore “light grade” brackets 1 mtr length bent to shape to obtained required shape including clamps, nuts / bots / washers etc connecting with suitable flexible copper wire of size 23/0.0076 complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement post top lantern LED type 40 watt 230 watt volts AC outdoor type with decorative post top for 360 degree indirect light IP 65 protection with impact and corrosion resistant complete with driver and lamp complete.complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in replacement LED land scape light/bollard light/garden light with excellent light output through its sleek PMMA window ensuring max illumination aspect in surrounding, 10W/9 W with 900mm height extruded aluminium cylindrical section housing IP-65 rated complete with base & log bolt grafite grey epoxy cationic powder coated all accessories including PCC foundation for fixing arrangement on ground complete all as specified. and directed by Engineer-in-Charge..

S&F copper cable flexible PVC insulated 3 x 2.5 sqmm single core along with earth wire in PVC conduit from FRP box to street light fitting ,including aluminium flat clampt 25 X 4 mm -03 Nos with suitable nuts,bolts and washers etc all as specified and directed by Engineer-in-Charge.

S&F copper cable PVC round sheathed (flexible) industrial cable 3 x 10.0 sqmm single core along with earth wire for high mast lights maintenance all as specified and directed by Engineer-in-Charge.

Supply & Fix in Replacement of GI Bracket made out of 40 mm dia medium grade GI tube up to 1.5 m long bend to shape 115 degree off set shape, fixed with 2 nos of suitable MS Flat clamp of size 40x5 mm with necessary nut bolts & washers and applying two coats of synthetic enameled paint over one coat of zinc oxide primer for clamp complete all as specified and directed by Engineer-in-Charge.

Material and Labour for painting of steel tubular pole 9 mtr long with one coat of aluminium paint including preparation old surface with scrapping of steel tubular poles Including numbering of pole no with black oil paint ,incl 2 strips of white & yellow paint , alternate upto a height of 1.2 mtrs complete all as specified and directed by Engineer-in-Charge.

Material and Labour for painting of Pre-stressed concrete pole 9 mtr long with one coat of white colour weatherproof snowsum paint including numbering of pole no with black oil paint ,incl 2 strips of white & yellow paint , alternate upto a height of 1.2 mtrs complete all as specified and directed by Engineer-in-Charge.

Supply and fix in replacement FRP cable looping box of size 250mm x 150mm x 100mm With connector block 4 Way , 1 Nos of MCB SP 6 Amp 10KA, etc including suitable Brass gland, including provision for connecting earth continuity conductor etc. all as specified and directed by Engineer-in-Charge. Make :- SINTEX / NATIONAL / NATRAJ.

Material and Labour for cement concrete Type C2 1:3:6 (40 mm graded aggregate of 150 mm thickness in foundation filling and mass concrete for filling of road cutting and making good for disturbed surfaces complete all as specified and directed by Engineer-in-Charge.

Material and labour for lowering of LED light fiitings mounting ring 20 Mtr to 30 Mtrs height carefully with help of highly skilled electrician and labours to mannually/electrically, Servicing Repair and replacement of spares of forward/reverse operation induction motor 3 phase 415 volts 2 HP capacity including greasing and oiling. Servicing of forward/reverse operation Gear box including greasing and oiling, dismantling and taking chain of motor to gear box, taking down unserviceable LED Light fittings and replacement of Suitable drivers of existing capacity/ Make its serviceable,supply and replace wire rope for lift side for suitable gauges/size,replacement of timer with power contactor three phese 415 volts AC 32 Amps capacity, After repairing of LED light fittings tesiting and make serviceable of all fittings and lifting of mounting rings to existing places, After repairing of LED light fittings tesiting and make serviceable of all fittings and lifting of mounting rings to existing places complete all as specified and directed by Engineer-in-Charge.

S & F timer switch with astronomical timer switch min 8KW, 3 pole, 230 V suitable for street light control including all assessories complete set all as specified and directed by Engineer-in-Charge.

Supply & Fix in replacement LED flood light fitting 120 Watts , 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection with impact and corrosion resistant ,Pressure die cast aluminium housing, heat resistant toughened glass with frame, uniform distribution ,including fixing arrangments with angle iron and suitable nut,bolt,washer etc on wall /on pole complete all as specified and as directed by Engineer-in-Charge.

Dismantling wrought iron or mild steel work of any discrption not otherwise provided for all as specified and directed by Engineer-in-Charge.

S&F posts and struts, brackets in fencing including cutting tops to shape as directed, drilling holes,notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc.,and similar work conforming to Fe-290 Gde E-165 all as specified and directed by Engineer-in-Charge.

M&L preparation of new steel surfaces of any description and applying two coats of synthetic enamel paintover a coat of red oxide primer all as specified and directed by Engineer-in-Charge.

S & F as in repairs Galvanized, 2 strand, steel barbed wire 2.24 mm dia barbed wire with 2mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts including securing or tying at crossing with and provision of galvanized mild steel wire steples or steel pins, etc , all as specified and as directed by Engineer-in-Charge.

M&L for galvanized Concertina coil, duly stretched, maintaining a dia of 600mm, concertina coil placed in U shape angle iron post erected over boundary wall and fixed to angle iron with 3mm dia GI bearer wire and fixed as in repairs, all as specified and directed by Engineer-in-Charge.

Demolition of cement Concrete of any description and in any position not otherwise specifically provided for, complete all as specified and directed by Engineer-in-Charge.

M&L for concrete(Type B2 1:2:4) in walls or retaining walls,any thickness, size or shape including pilasters, buttresses columns, pillars,boundary pillars and posts (including caps and bases) all as specified and directed by Engineer-in-Charge.

M&L Formwork to faces of walls,retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses,etc.; vertical or to batter all as specified and directed by Engineer-in-Charge.

M&L for cement concrete type B1(1:2:4) in copings ,apex stones, kerbs rounded or chamfered angles, drain beds and throating complete all as specified and directed by Engineer-in-Charge.

Raking out joints/ pointing to random rubble masonry, courced or uncourced built in cement mortar, complete all as specified by Engineer-in-Charge.

M&L for Raised pointing to random or polygonal rubble, uncoursed or brought upto courses in CM (1:4), complete all as specified and direted by Engineer-in-Charge.

Demolition of cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level), complete all as specified and direted by Engineer-in-Charge.

M&L for 75mm thick cement concrete type D2 1:4:8 as in sub bases, sub floors etc , complete all as specified and directed by Engineer-in-Charge.

M&L for rubber moulded glossy finish coloured Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors over 15mm thick screed bed in CM 1:6, complete all as specified and directed by Engineer-in-Charge.

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block (anti fungel) of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; including removing old damaged tiles complete all as specified and directed by Engineer-in-Charge.

Dismaintling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed by Engineer-in-Charge..

Supply and fix Pre-painted Galvalume Aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified and directed by Engineer-in-Charge.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles , complete all as specified and directed by Engineer-in-Charge.

M&L for brick work with sub class B bricks , straight or curved on plan exc 6m mean radius built in cement mortar 1:6 all as specified and directed by Engineer-in-Charge.

M&L Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted except stone, built in cement mortar 1:4, complete all as specified and direted by Engineer-in-Charge..

M&L for Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto courses, Hammer dressing with maximum depression on face from straight edge held against the dressed surface n exc. 20mm for granite or trap stone, complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster on brick wall including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 15mm thick CM 1:4 on brickwork or concrete surface of walls and finised surfaces even and smooth without using extra cement , complete all as specified and directed by Engineer-in-Charge.

Removing of debris / earth obtained from demolition items / excavation including loading /unloading etc , outside MD Land, upto 60 KM as per BMC guidelines all as specified and directed by Engineer-in-Charge.

NANGIA AND CO (BID ID -3237826)