ADDN ALT CUM SPECIAL REPAIRS TO OFFRS JCOS OR/MES KEY PERSONNEL MD ACCN INCLUDING FAFA ACCN AT VIDHAYA VIHAR UNDER GE AWC MHOW

Amount

M & L for Roughening / taking down existing roof treatment surfaces including plaster over old concrete roof by picking, sweeping clean and washing down with water to remove dust etc. all as specified and directed.

M & L Brushing neat cement slurry with 3 Kg of cement per Sqm for bonding of old concrete surface to new concrete/plaster surfaces complete.

M & L Cutting out cracks to 6 mm wide 'V' section in existing roofs or terrace (if cracks > 2.5 mm wide), cleaning out, wetting, grouting with and including chemical compound SUPER LATEX of DR. FIXIT of PIDILITE INDUSTRIES LTD or SBR LATEX of STP LTD,, water and cement Sand slurry in the proportion of (1:3) by weight mix or as per manufacturers instructions all as specified and directed complete.

M & L PCC 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate) mixed with integral waterproofing chemical PIDIPROOF LW of DR FIXIT of PIDILTE INDUSTRIES LTD or STP No. 1 (LIQUID) of STP LTD @ 200 millilitre per 50 Kg per cement, as in padding on roof surface for correcting / making proper slope on roof, and finishing the surfaces fair and even without using extra cement complete all as specified. Note:- Liquid WPC shall be measured and paid separately.

M & L 10 mm thick rendering in CM (1:3) mixed with integral water proofing chemical compound PIDIPROOF LW of DR FIXIT of PIDILITE INDUSTRIES LTD or STP No 1 (liquid) of STP Ltd @ 200 mililitre per 50 Kg cement as per manufacturers instructions over concrete surface and finishing the surface fair and even without using extra cement complete all as specified.Note:- Liquid WPC shall be measured and paid separately.

Supply only liquid water proofing compound complete PIDIPROOF LW of DR FIXIT of PIDILITE INDUSTRIES LTD or equivalent make STP No 1 of STP Ltd.

M&L Water proofing treatment on "Non approachable / non accessible roof" surface (Horizontal & Vertical surfaces) in following sequence through authorized applicator of the manufacturer all as specified and directed complete. (i) Cleaning of new rendered surface properly and drying the surfaces. (ii) Applying a coat of oxidised bitumen based solvent primer @ 0.30 Kg/ Sqm. (iii) Laying 3 mm thick APP modified water proofing membrane with 100 mm over laps sealed and bounded to the surfaces by 'torchon' method. (iv) Applying two coats of bitiminous aluminium pait @ 200 Gram / Sq M (minimum) in two coats. Make incorporated : HYPERPLUS of IWL (INDIA) LTD or equivalent in Pidilite industrries Ltd / STP Ltd all as specified and as manufacturer instruction complete.

M & L for plain aluminium sheeting 0.56mm thick bright finished bent/cut to shape ( for covering parapet top, side of roof projection and other similar works) fixed with flat aluminium 10 x 2 mm and screw PVC raw plug @ 300 C/C distance complete all as specified and as directed by GE.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specially provider for complete.

M&L for PCC 1:5:10 mass cement concrete type E2 as in suken floor complete

Dismantling PVC water tanks Exc 250 ltrs but not 500 ltrs including taking down of float valve and removing from site complete.

S&F 1000 Ltrs capacity double layer (ISI marked) rotational moulded polyethylene water storage tanks, (cylindrical vertical with closed top) hoisted and fixed in position, all as specified in SSR part I complete.

S&F in repair ball valve/float ball high pressure of PTMT 20mm with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed minimume weight 210 gm etc all as specified and directed.

Taking up or down existing steel tubing and connection complete for following sizes:-

15 mm dia

20 mm dia

Supplying, fixing, jointing and testing galvanised steel water tubing medium grade with all fittings such as bend, elbow, socket reducer etc fixed to walls and ceilings or laid in floors, complete for the following sizes: -

15 mm dia bore

20 mm dia bore

Dismantling of floor hearth or wall tilling including cement mortar bedding (but not backing) and rubbish of the premisses complete all as specified and directed.

M&L non skid/mat finish ceramic colour tiles 7 to 8 mm thick(square/ rectagular) area of each tile exceeding 0.11 sq m but not exceeding 0.18 sqm (Colour and design of tiles as approved by GE), in floors etc, and jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

M&L glazed ceramic coloured tiles size 300mm x 450 mm x 6-7 mm thick (Colour and design of tiles as approved by GE) on vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L non skid/mat finish ceramic colour tiles 7 to 8 mm thick(square/ rectagular) area of each tile exceeding 0.18 sq m but not exceeding 0.38 sqm (Colour and design of tiles as approved by GE), in floors etc, and jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

M & L for double charged vitrified cerameic tiles 9 to10mm thick light shade (square/rectangular ) polished, area of each tiles not exceeding 0.36 sqm in floor/skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 20 mm thick screed in cement mortar 1:4 complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar complete all as specified and directed

M&L Granite 18-20 mm thick(of any type) work (table rubbed and polished) for wall lining (Veneering to wall) and laid on cill of parapit wall over 12 mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite colour Red or brown as per direction of GE

M & L 22 - 25 mm thick mirror polish machine cut Kota stone slab in flooring or treads single piece of steps over and including 15mm thick screed bed in cement mortar 1:6, laid and jointed with grey cement slurry mixed with pigment to match with shade of slab including rubbing complete all as specified and as directed. Note:- The size of Kota stone slab shall not less than 550 mm x 550 mm cut size, except the location where the balance portion remain less than size as specified above.

Ditto all as per item No 23 above but as in skirting or vertical surfaces over and including 10 mm thick rendering in cement mortar 1:4, complete all as specified and as directed.

Taking down chowkhats or frames not exc 1.5 sqm each without taking off shutter from the frame complete.

Taking down chowkhats or frame exc 1.5 sqm but not exc 4 sqm with shutter (without taking off shutter frome the frame) complete

S & F 125 x 60 mm size Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate,hold fast includ etc., complete as specified

S & F 105 x 60 mm size Pressed steel frames for door with one or more rebates including necessary lugs, hinges, lock strike plate,hold fast include etc., complete as specified

M&L for PCC (1:3:6) type C-1 with using 20mm graded stone aggregate as in bed blocks, coping, for fixing holdfast/lugs,filling hollow space of pressed steel door frame etc including necessary form work all complete as specified and as directed.

M & L 2 nd class hard wood 35 mm thick Plain , framed panelled shutters ( any number of panels), with panels of timber flat on both sides (feather edged) or of veneered particle board medium density, wood particle board with commercial face veneers fitted to chowkats complete all as speciifed and directed.

S & F 2 nd class hard wood 35 mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass , gauze, etc, (without sash bar) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR Part-I, section 8, clause 8.24 (a) fitted to chowkats complete all as specified and directed. Note :- Glass pane and wire mesh shall be measured and paid separately in respective supply only item.

M & L providing factory made 100% solid WPC (wood polymer composite) door frame 90 mm X 45 mm (straight) single rebated, made form wood polymer composite) Single extruded process) material compressing of virgin PVC polymer of K value 57-60 (suspension grade). calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and nor toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body treaded star headed screws having minimum frame density of 780 kg/ cbm. Manufactured by ISO 9001-2015 certified company , having good screw holding capacity (screw withdrawal strength of (Min 990 N) minimum compressive strength of 58 N/mm square, modulus elasticity 900N/mm square and resistance to spread of flame of class A category with property of being termite/ borer proof, water/ moisture proof & fire retardant & fixed in position with SS dash fasteners / hold fast of required dia the and lenght, all as directed by the engineer-in-charge. material test certificate and authentication should be compulsory provided by the manufacturing company (hold fast or dash fasteners shall be paid separately). Make : SYNTEX/RAJSHRI plastiwood equivalent as approved by the GE.

M & L providing factory made 24 mm Thick 100% solid WPC (Wood Polymer Composite) Plain/ laminated flush door shutter of required size comprising of virgin PVC resin of K value 57-60 (suspension Grade) calcium carbonate and natural fibers (wood powders/ rice husk/ wheat husk) and non toxic additives made from extrusion process WPC foam sheet single extruded (inner) with density not less than 650 kg/cbm. Manufacturred by An ISO 9001-2015 certified company having good screw holding capacity (screw withdrawal strenght of 2000N (Face) & 1100 N (Edge), minimum compressive strength of 50N/mm square, modulus of elasticity 850N/mm and resistance of spread of flame of class A category with property of being termite/ borer free. water / moisture proof and fire retardant and fixing stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws. all as per direction of engineer-in-charge, material test certificate and aughentication should be compulsory provided by the manufacturing company for WC/ bathroom/ toilet/ kitchen/ balcony doors. Make : SYNTEX/RAJSHRI plastiwood equivalent as approved by the GE.

S & F 100 mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete .

S & F aluminium 200 mm long anodised barrel tower bolts ISI marked of extruded section and fixed complete.

S & F aluminium 150 mm long anodised barrel tower bolts ISI marked of extruded section and fixed complete.

S & F 150 mm size aluminium handles cast type, anodised ISI marked complete

S & F 250 mm aluminium alloy, anodised sliding door bolt ISI marked with hasp, staple (bolt type) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sec or cast aluminium and fixed complete.

S & F 300 mm mild steel, ordinary rat tail rod pattern spring including roller and roller plate complete fixed to steel frame / wooden frame including necessary welding, cutting, opening of wall for fixing bracket and making good complete.

S & F in repair powder coated aluminium door seal 30mm wide and length as per requirement of site including dust/insect arrestor complete all as specified and directed.

S & F Powder coated aluminium sliding glazed windows with three track shutter sliding (two shutters glazed and one shutter wire mesh) shall be two part as upper part shall be three movable shutter and lower part consist three shutter (one openable in centre and both side fixed type shutter with frosted glass) with following specification including MS grill of 10mm solid square bar of 150mm c/c horizontal and two 10mm soli square bar vertically alongwith alround frame using 30mm x 3mm flat with necessary welding and fixing anchorage included and making good the adjacent side of jombs of windows by plastering in CM 1: 3 even and smooth complete etc . shifting of existing cooler stand where required complete all as specified and as directed by Engr-in-charge. (Note :- The rate for fixing of MS grill shall be included in quoted rates)

(i) Windows frame of cross section 101mm x 44mm x 1.5mm thick. (Min) (ii) Three way track for sliding shutters of cross section 91.8mm x 31.75mm x1.1mm thick.(Min) (iii) Sliding shutter frame of cross section 40 x 18 x 1mm thick.(Min) (iv) 4 mm thick glass superior quality.(Min) (v) IDPE Rubber guasket for fixing of glass. (vi) Locking cleats per shutter -01 Nos.(Min) (vii) Sliding rollers per shutter - 02 Nos.(Min) (viii) Stainless steel wire cloth 0.30mm nominal dia of wire and average width of aperture 1.40mm for shutters 01 Nos. (ix) fixing screw for frame with wall per windows- 08 Nos.

S & F powder coated aluminium ventilator cross section conforming to IS 63.5 x 38.10 x 1.5mm consisting of two partions upper portion shall have louvers with 3mm thick pin headed glass and aluminium wire cloth 0.30mm nominal dia of wire and average width of aperture 1.56m fixed with aluminium beads and securing on outer face of frame and lower portion of ventilation shall be fixed with 3mm thick pin headed glass with IDPE rubber gasket including aluminium beads, including MS grill of 10mm solid square bar of 150mm c/c horizontal and two 10mm soli square bar vertically alongwith alround frame using 30mm x 3mm flat with necessary welding and fixing anchorage included and including preparation of jombs all around in CM 1:3 finishing even and smooth complete all as specified and directed. (Note :- The rate for fixing of MS grill shall be included in quoted rates)

M&L mild steel framed work such as grills , gratings, etc., with ends of bars shouldered and/ or riveted, or forged in to spikes; framed guard bars ; barred iron doors; ladders; framed balusters ; walk ways ; railings; frame work of water tanks and similar work conforming to Fe-290 Gde E-165 complete all as specified.

S& F 18/19 mm thick Block boards, grade 2 quality, interior grade, commercial type, conforming to IS fixed with screws timber frame work as in cupboard , wardrobe etc.

M & L 0.9 mm thick Decorative laminate type 1, of surface finish, colour and pattern as approved, conforming to IS fixed with approved adhesive over 18/19 mm thick plywood as per manufacturer's instructions complete all as directed and specified.

S&F Aluminium, anodised, barrel tower bolts of extruded section and fixed, 100 mm length of bolt, ISI marked complete all as specified.

M & L 2nd class hard wood n.exc 6 sq.cm Plain fillets square, rectangular or triangular in section, clean sawn, secured with nails or brads.complete all as directed and specified.

S&F Aluminium handles, cast type anodised 'D' shaped , 100mm long ISI marked all as specified.

S & F 100 mm length Hasp and staple, mild steel, wire type stove enemelled black , including bolt to hinge plate and fixed with screws complete all as specified and directed.

M & L for preparation old painted surfaces of steel and iron work of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M & L Preparation of New wood or previously untreated surfaces of any description , not otherwise description, over 10 cm width or grith apply two coat of synthetic enemel paint (ordinary tint) over a coat of pink primer complete all as specifed and directed.

Hacking out old broken glass pane (any thickness , size, quality or description) from steel frame glazed with putty or fixed with beads.

M & L for 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc. 0.5 sq m in each pane complete all as specified and directed.

M & L for 3 mm thick figured glass ordinary quality and glazing with oil putty in square not exc. 0.5 sq m in each panecomplete all as specified and directed.

S & F in repairs Galvnised mild steel wire cloth, 0.56mm conforming to I S nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, wooden beads or galvanised wire staples etc complete all as specified and directed.

Demolition of Brick work built in cement mortar including all quoins arches pillars etc complete all as specified and directed

M&L Brick work with sub class 'B' modular brick straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed

M & L for reparing of RCC projection, chajjas,roofs,facia, colum etc by necessary preparation i.e scrapping ,cutting,chiseling,derusting and cleaning exposed reinforecement, surfaces of damaged, loose RCC surfaces and applying one coat of rust remover by brushing to rusted reinforecemnt to remove loose rust particles and allow to dry it for 2 to 3 Hrs , insert the new reinforcement to damaged portion by drillig hole at required distance , fill the epoxy in to the hole by 2/3 of the hole and insert the reinforcement in the hole, and binding the reinforcement at rusted portion of reinforcement, apply cement slurry on entire damaged area , and plaster the surfaces with cement , sand and Polymer liquid in 1: 3 : 15% of cement by weight ) and water as required , mixing properly and plaster the surface , finished even and smooth by making the edge water dropping groves complete all as specified and directed. Note : - Cost of formwork shall be deemed to be included.

M&L for 10 mm thick rendering in cement mortar (1:6) first coat on fair faces of brick walls or concrete surfacesand in cm 1:4, 5mm thick second coat over first coat , mixed with water proofing compound as per manufacturer instructions, finishe fair and even without using extra cement all complete as specified and as directed incl taking down existing plaster.

Supply only Integral water proofing compound complete.

M&L for rendering 10mm thick plastering in CM (1:6) finished even & fair all as specified incl taking down plaster.

M&L for rendering 5mm thick in CM 1:3 as in soffits of ceiling and Rcc cjhaja/ Facia roof projections finished fair & even all as specified incl taking down plaster

M&L for applying three coats of white washing on new plastered surfaces of ceiling including preparation complete all as specified and as directed.

M & L preparing old decorated plaster or un-plastered surfaces of ceiling and applying one coat of white wash complete all as specified and as directed.

M & L Preparing newly plastered or unplastered wall surfaces all as specified and directed.

M&L for applying two coats of cement base paint on new plastered surfaces of wall including preparation complete all as specified and as directed.

M&L for preparing of old surfaces of walls and applying one coat of cement base paint all complete as specified and directed.

Complete removal of old treatment on internal surfaces of wall by scrapping , and washing etc all as specified.

M&L for applying 1 mm Avg thick wall care putty on wall on internal old/new wall surfaces as per manufacturerer instruction complete all as specified and as directed

M & L for applying two coats of oil bound distemper over a coat of primer on prepared wall putty surfaces of internal wall all as per specified and directed. (Note :- Paint shall be applied with roller only and work shall be only executed through authorized , certified applicator after approval obtained from GE).

Demolition of cement concrete (un reinforced) in ground floor and paving n. exc. 15cm thickness (below or above ground level complete.

M&L for PCC 1:3:6 type C2 using 40mm graded aggregate 75mm thick as in plinth protection, finished concrete surfaces even and smooth without using extra cement

S & F in repairs Sink with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes coupling , including bedding in cement mortar to dwarf wall or including fixing cantiliver brackets and connecting union to pipe overall size 915 mm x 460mm bowl size 410 mm x 330 x 160 mm complete all as specified and directed. Make :- Nirali , Diamond ,Jain Brothers Sanitation Pvt Ltd

S & F in repairs vitreous china wash hand basin white, flat back of size 550mm x400mm fixed on and including cast iron cantilever bracket, 32mm dia brass waste coupling and 32 mm dia PVC waste pipe including fixing of tap, waste fitting etc complete.. Note :- Pillar tape shall be measured as supply only under respective item

supply only 15 mm dia bore pillar tap fancy typecast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered ‘HOT’ or ‘COLD’ with long screwed shanks and fly-nuts, screwed for iron pipe complete .

S & F( in repairs) Vitreous chaina wash down water closet pan (pedestal pattern), white including pedestrial pan and trap, including seat cover for pedestial pan and connecting to drain or outgoing pipe and to flushing pipe, antisyphonage pipe etc complete all as specified and directed. Make :- Parryware (Super fine), Hindware,Johnson Pedder .

Supply only ( ISI Marked) Coloured Plastic water closet seat, back, closed pattern with flat bottom , and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S & F in repair vitreous china squatting pan “ORISSA PATERN” of size 580 mm x 440 mm, white, with integral foot rest (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, anti syphonage pipe etc and making good to floor complete.

Supply only10 Ltr capacity,PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets with and including 32 mm dia PVC flush pipe complete all as specified and directed. Note:-Fixing only rate is included in item No above.

Supply only PVC connection pipe 15 mm dia 450 long with PTMT nut at both ends complete.

S & F (in repair) brass chromium plated angle cock 15 mm dia screwed for iron pipe or brass ferrule, complete. Make : Plumber Cat No FLP-0507/Prayag Cat Part No 7810/ Jaquar Cat Part No CQT-23059 complete all as specified .

S & F in repair brass chromium plated towel rail 20 mm outer dia Bracket type, 60 cm long between flanges with and including chromium plated brass screws and wooden / plastic cleats, complete. Make : Plumber Cat part No U-0911/Prayag Cat Part No BA-10/Jaquar Cat Part No AQN-7711 complete all as specified and directed.

S & F in repair over head shower with arm & flnge of chromium plated with or without swivel joints, any size, including fixing to 15mm dia steel pipe for required length or union Make: Plumber Cat part No.ITP-2401/Prayag BOS-90 Cat Part No SHP-524/Jaquar Cat Part No OHS 1989 complete all as specified and directed

S&F in repair 15 mm dia consealed type stop valves, cast copper alloy, chromium plated, screwed down, high pressure with handle, screwed both ends for iron pipe or union complete all as specified and directed

S&F 15mm dia Bib tap chromioum plated with crutch or butterfly handle sorewed down screwed for iron pipe or for brass ferrule and fixedcomplete. Make : Plumber Cat part No FLP-0203 /Prayag- PIS-08, Jaquar Cat No CON-107KN complete all as specified and directed.

S&F in repairs powder coated steel peg set having 06 Nos spikes fixed to wall complete all as specified and directed (Make as spproved by GE)

S & F in repair PVC bath cabinet box mirror type with shutter complete. (Make :- Prayag Cat No -551 or equilent of plumber/ESS/jaquar etc.)

S&F harrison rail/curtain rod, mild steel chromium plated with fixing bracket, stops and complete fitment all as specifed and as directed.

S & F in repair corner shelf of 300 mm size with ABS brackets complete. Make : Prayag Cat No - BEA - 52 or equiilent of Jaquare CAT NO - CAN-1173/Plumber CAT NO- U-0921 complete all as directed and specified.

Supply only 15 mm dia bore basin mixture brass chromium plated with capstan heads screwed down high pressure with or without letter ‘HOT’ or ‘COLD’ with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed. (Make : Plumber Cat part No AZT-3104/Prayag : Cat part CAT NO-8750/ Jaquar Cat Part No FLR-5167NB)

S & F in repair CP Thumbler Holder, complete all as specified and directed by Engineer-incharge. MAKE:- Plumber Cat Part No. U-0914/ Prayag Cat Part No BA-16/ Jaquar cat Part No-AQN-7741

S & F in repair Bidet spray (Health faucet) with 1 meter tube and holder, complete all as specified and directed. (Make : Plumber Cat No IT - 1904 ITALIAN / Prayag Cat Part No- BEA-87 /Jaquar CAT PART NO - ALD-CHR-583)

S & F in repair CP Toilet paper holder, complete all as specified and directed by Engineer-incharge. MAKE:- Plumber Cat Part No. U-0916/Jaquar Cat Part No AHS1551 /OR Prayag Cat No- BA-88 complete all as specified and directed.

S&F in repair CP wall mixer, for mixing hot and cold water fancy type cast copper alloy , with capstan heads, chromium plated , screwed down for 15 mm bore pipe,high pressure with long screwed shanks and fly-nuts , screwed for iron pipe ISI Marked of other specified.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets of any thickness, including cover fillets complete.

M&L false ceiling with GI powder coated frame work and 4mm thick, white pre-premiered and painted self embossed, reinforced designer board conforming IS- 14862 and ISO-8336, duly suspended with ceiling complete all as specified and directed by Engr-in-charge.

S & F in repair Gun-metal, globe of gate balve /flush cock of 20mm bore with iron wheel head, screwed both ends for iron pipe etc all as specified.

S & F in repair PVC (SWR) nahani trap with grating having diameter of outlet 75 mm including joining to waste pipe with solvent cement complete.

S & F in repair 110 mm dia bore. PVC (SWR) pipes single socketed in any length with rubber ring joints,laid in floor/ trenches complete all as specified and directed.

S & F in repair 75mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring joints,laid in floor/ trenches complete all as specified and directed.

S & F in repair 110 mm dia bore. PVC (SWR) pipes single socketed in any length with rubber ring joints,fixed to walls complete all as specified and directed.

S & F in repair 75mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls complete all as specified and directed.

S & F in repair 110 mm dia bore PVC (SWR) bends with acess door any radius with solvent rubber ring joints, fixed complete all as specified and directed.

S & F in repair 75mm dia bore PVC (SWR) bends with acess door any radius with solvent rubber ring joints, fixed complete all as specified and directed.

S & F in repair 110 mm dia bore PVC (SWR) junction single, single (T) equal or unequal with acess door with solvent rubber ring joints, fixed complete all as specified and directed.

S & F in repair 75mm dia bore PVC (SWR) junction single, single (T) equal or unequal with acess door with solvent rubber ring joints, fixed complete all as specified and directed.

S & F in repair 110 mm dia bore PVC (SWR) branch piece single (single Y) equal or unequal with rubber ring joints, fixed complete all as specified and directed.

S & F in repair 75mm dia bore PVC (SWR) branch piece single (single Y) equal or unequal with rubber ring joints, fixed complete all as specified and directed.

S & F in repair 110 mm dia bore PVC (SWR) vent cowl rubber ring joints, fixed complete all as specified and directed.

Excavation in trench in avy type of soil not exceeding 1.5M wide and not exceeding 1.5M in depth for sewage line, manhole etc not exceeding 10 sqm on plan and getting out in any type of soil complete.

Returning, filling in Soft/Loose soil including spreading, watering and well ramming in layers n. exc 25 cm thick in any type of soil complete.

Removing excavated material to a distance n exc 50M and deposited where directed at a level n. exc 1.5M above the starting point complete.

Demolition and breaking up drain pipe of dia 150 mm (internal dia) (salt glazed stoneware, AC or reinforced conrete) set in cement mortar complete all as specified and directed.

M & L cement concrete bed to drain pipe including packing under and haunching against side of pipe after they are laid and tested in cement concrete 1:3:6 type D-2 using 40 mm graded stone aggregate for the 150 mm internal dia of pipe complete all as specified and directed

Demolition of reinforced cement concrete of any description for manhole cover, slab of septic tank & soak well etc complete.

M & L providing pre-cast cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in cover slab of manholes, septic tank, soak well etc set in cement mortar 1:4 with plain fair faces including chamfered weathering, throating etc including necessary use and waste of form work complete.

S & F mild steel TMT bars 10 mm dia and over as in reinforcement, cut to length, benty shape required including cranking, bending, spirally for hooping for columns, hooking ends and hinding with mild stee wire (annealed) not less than 0.9 mm dia or securing with clips complete.

Surface excavation n. exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in any type soil complete all as specified and directed

M & L hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface

M & L PCC 1:4:8 type D-2 using 100 mm graded stone aggregate as in mas concrete complete all as specified and directed.

M & L 60 mm thick Machine pressed precast concrete interlocking paver blockfixing with grey cement and pigments OF " I " shape or as approved by GE ,and any colour and size confirming to IS 15658-2006 of M-35 Grade set , laid over 50 mm (average) thick dust sand cushioning,filling of joints with sand & compaction using surface vibrator after filling of joints lain in any pattern as decided by Engineer-In-Charge including packing of sides by cement concrete finishing surfce even and smooth complete all as specified and as directed. Note : Sand cushioning shall be measured and paid separately .

S & F Joist channel, angle or tee, square or rectangular tubler sections fixed independently or as purlin, rafter or post incl cutting to dead length where required notching drilling firing riveting and/or welding or connecting with bolts and nuts providing and fitting angle cleats fish plates, gusset plates etc complete all as specified and directed (Fe-410-W (gde-E-250) quality A) complete

S & F Pre-painted galvalum aluminium zinc coating steel based corrugated steel sheet 0.50mm thick (total coated thickness) of any colour having tensile strength of 550 Mpa minimum, yeild strength, it shall be coated with hot dip alloy of 55% aluminimum, 43.5% zinc,1.5% Silicon and finished with resin coat on both surface @ 150 gm/ sqm of coating as specified and shall be fixed with hot dip galvanised, self drilling and self tapping screws neoprened and EDPM washers as in roof covering all as directed at site all as specified and dircted.

Treating the soil under the plinth protection at the rate of 5 litre of emulsion per square metre of surface area.complete all as directed and specified.

Treating of soil under existing floors using emulsion @ one litre per hole , 300 mm apart including drilling and pluging 12 mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match existing floors.

M& L At points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete

M&L for preparation old decorated surface of wall/ceilling to be done by mechanical means/smart painting technique coats of acrylic latex base exterior grade (100% ACRYLIC) over a coat of primer at any height including necessary scaffolding complete alongwith five year warrantly complete all as specified and directed (Make:- Asian Paints Apex/ Dulux Weather Shield or equvalent). Note:- Painting work shall be executed through authorized and certified applicator of paint manufactures of paint companies. 2. Approval shall be obtained from GE for make/manufacturers and applicator before engagement in the work. 3. Contractor shall provide five year written guarantee certicate for the paint work.

M&L for applying one coat primer acrylic polymer modified water proofing coating (Brushband of FOSROC or equivalent) and over that two coats of acrylic polymer modified two component elastometric water proofing membrane coating (Brush band of Fosroc or equivalent) complete all as specified as per manufacturers instruction as directed (Make :- Dr Fixit, Fosroc, Sika) . Note :- 1. This item shall only be executed through level 4 or level 5 certified and authorized applicator of the company. 2. A warranty for 5 years in the form of written agreement shall be submitted by the contractor. 3. The rate quoted by the contractor shall include all the provisions mentioned in this item including notes.

Refixing of existing water tank including all necessary fittings and fixtures complete all as specified and directed.

Taking down copper /aluminium point wiring (light, fan, bell,socket or power) complete including fixture and fittings such as switches , ceiling roses , pendent , regulators, sockets, light fitting etc. Removing materials to store for keeping in safe custody or for taking credit (credit a for above items should be made as per condition seperately) and making good distrubed surfaces of walls, floors etc.

Taking down old/unserviceable distribution board by disconnection of electric connection carefully SPN DBs/TPN DBs/ Main Switch including old unserviceable MCCBs/ MCBs, Isolators, etc and making good to disturbed surface all as specified and directed at site.

Taking down carefully copper/aluminium Sub main wiring of any size from surface/concealed /existing conduit of any height and removing materials at site and making good disturbed surfaces of walls, floors roofs etc complete all as specified and directed.

Taking down existing geyser of any capacity after disconnecting all necessary electrical and water supply connections and deposit to MES store yard of AGE E/M No II complete all as specified and as directed.

Taking down ceiling fan/ exhaust fan of any sweep after disconnecting all necessary electrical connections from ceiling rose to fan, fan blades and deposit to MES store yard of AGE E/M No II complete all as specified and as directed.

Taking down existing single phase electric energy meter of any capacity after disconnecting all necessary electrical connections and deposit to MES store yard of AGE E/M No II complete all as specified and as directed.

M&L for point wiring with 1.5 Sq mm single core PVC insulated unsheathed copper FRLSH multi stranded conductor cable in and including Concealed PVC conduit of size 20/25mm ISI marked inclusive of tees ,bend ,elbows etc upto and including sunk in anodized pressed steel box for housing switch socket etc with white laminated 3 mm thick sheet cover ISI marked of suitable size complete including PVC insulated multi stranded copper conductor 1.5 Sq mm FRLSH cable as earth wire to common earth dolly for connection to ceiling rose to earth terminal including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed by Engr-in-charge for following :-

(a) One light point controlled by one, one way switch 5 Amps

(b) One fan point/ exhaust fan point controlled by one, one way switch 5 Amps and regulator

(c) One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

(d) One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent boad.

(e) One light point controlled by one, two way switch 5 Amps

(f) One bell point controlled by one, bell switch 5 Amps

Ditto all as per item No 135 here in before but using 2.5 sq mm single core copper conductor cable of multistranded FRLSH PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of 2.5 sq mm copper conductor FRLSH PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly.

M & L for Point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5 Sq. mm (nominal area), two single core, PVC insulated and unsheathed FRLSH cable 1100 volts grade ISI-694 marked drawn through in and including heavy duty, PVC concealed conduit of white/ ivory colour including all accessories after chasing in wall/ceiling etc, heavy duty ISI marked, with GI sunken boxes 1.2 mm thick, 60 mm deep with earth dolly duly, covered with modular white cover plate with inner frame suitable for modular switches, including PVC insulated multistranded copper conductor 1.5 Sqmm (nominal area) single core FRLSH cable as earth continuity conductor to common earth and connecting to earth dolly including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed for the following :-

(a) One light point controlled by one, one way switch 5 Amps

(b) One fan point/ exhaust fan point controlled by one, one way switch 5 Amps and regulator

(c) One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent boad.

(d) One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

(e) One bell point controlled by one, bell switch 5 Amps

Ditto all as per item No 137 here in before but using 2.5 sq mm single core copper conductor cable of multistranded FRLSH PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of 2.5 sq mm copper conductor FRLSH PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly.

Ditto all as per item No. 137 here in before but using 4.0 sq mm single core copper conductor FRLSH cable of multistranded PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of 4.0 sq mm PVC insulated copper conductor FRLSH cable as earth continuity conductor along with wiring and connecting to the common eath dolly. (for AC Point)

S & F for Switch Piano type single pole 5 amp, 230 Volts complete all as specified and directed at site.

S & F for Switch Piano type 2 way switch 5 amp, 230 Volts complete all as specified and directed at site.

S & F for switch bell push piano type 5 amp, 230 Volts Complete all as specified and directed at site.

S & F for socket outlet 2 in 1 , 5 pin, 5 amp, 230 Volts complete all as specified and directed at site.

S & F for Ceiling rose, surface Bakelite with 3 terminals, ISI marked for batten fitting complete all as specified

S & F for stepped type electronic fan regulator flushType complete all as specified and directed at site.

S & F for Modular Switch , single pole, one way, and 5/6 Amp single module complete all as specified.

S & F for Modular Switch , single pole, one way, and 15/16 Amp single module complete all as specified.

S & F for Modular Socket outlet multipurpose having provision for 3 pin, 5/6 Amp and 2 pin, 5/6 Amp, 2 module complete all as specified.

S & F for Modular Socket outlet multipurpose having provision for 3 pin, 15/16 Amp and 3 pin, 5/6 Amp, 2 module complete all as specified.

S & F for modular step type fan regulator 120 watt 2 module suitable for 230 volt 50 Hz AC supply complete all as specified and as directed.

S & F for for Bell push modular 6 Amps single module complete all as specified.

S & F for lamp holder PVC / Polycarbonate type with back plate suitable for batten/ slanting fittings complete all as specified and directed.

S & F for Bell Electric Ding dong type suitable for operation on 230 volt 50 HZ A C supply complete all as specified and as directed

S & F for Modular type TV Socket out let complete all as specified and as directed.

M & L for Sub main wiring with approved colour coding as per IS with four single core PVC insulated FRLSH cable with stranded copper conductor of size 6 Sq mm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc two runs of PVC insulated with 6 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire complete all as specified and as directed. Note:- Four runs of 6 sqmm cable, two runs of 6 sqmm cable and one run of PVC conduit will be measured as one unit

M & L for Sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLSH cable with stranded copper conductor of size 6 Sq mm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc one run of PVC insulated with 6.0 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire complete all as specified and as directed. Note:- Two runs of 6 sqmm cable,one run of 6 sqmm cable and one run of PVC conduit will be measured as one unit

S & F for sheet metal enclosure MCB DB TPN 4 way Vertical type with 200 Amps rated bus bar 415 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed. (Make:- LT/Schneider/Legrand/ABB)

S & F for sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed. (Make:- LT/Schneider/Legrand/ABB)

S & F for MCB tripple pole and neutral rated capacity 63 Amps, 415 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed. (Make:- LT/Schneider/Legrand/ABB)

S & F for MCB Single pole and neutral rated capacity 40 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed. (Make:- LT/Schneider/Legrand/ABB)

S & F for MCB Single pole rated capacity 5 to 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.(Make:- LT/Schneider/Legrand/ABB)

S & F for metal clad box suitable for 230 volt 50 Hz AC supply three pin with MCB SP 20/32 Amps including removal of old unserviceable one complete all as specified and as directed complete all as specified and as directed (Make:- LT/Schneider/Legrand/ABB)

Supply and fixing in replacement of water heater storage type of 5 Star rating, capacity 25 liters with , glass coated heating element to protect the heating element from oxidation and carbonization. The geyser should be tough enough to withstand pressure upto 8 bars . The inner tank should have a minimum 7 years warranty . The geyser should have ELCB or shock safe plug including PTMT connections 15 mm size with nuts and length of 450 mm with all fixing arrangements. complete all as specified and as directed. (Make:- Havells/Jaquar/Racold)

Supply and fix in replacement of ceiling fan 1200 mm sweep , BLDC fan,BEE rated 5 star ceiling fan or above with 350 RPM or above with power factor of >/=.0.90 for air delivery of 220 M/Cum minimum service value of 7 with electronic modular type fan regulator 1 module or with remote, complete all as specifeid and as directed. (Make:- Havells/Orient/Crompton)

Labour only for refixing the celing fan/ Exhaust fan obtained from item No 133 above with replacement of unsv 3 core PVC insulated PVC sheated 3 core multistranded copper conductor cable of size 23/ 0.193 from ceiling rose to fan terminal including over hauling the fan, painting of ceiling fans complete with two coats synthetic enamel paint by spraying including filling cavities with filler after cleaning all dust etc. including replacing canopies, rubber bushesh, nut, bolt & washers complete all as specified and as directed.

S & F for Highly efficient LED Bulbs, 10 W, 5 star rated used as a ready replacement for existing GLS/CFL direct fit lamp,in B-22 cap of Make Bajaj, Havells, Philips, Wipro complete all as specified and directed

S & F for Decorative wall mounted luminaire made out of polycarbonate with unbreakable globe suitable for LED bulb and provosion of LED bulb 10 watts 5 star rated complete all as specified and as directed. (Make Havells Cat No LHDLO6160099 or its equvalent in Philips, Bajaj).

S & F for LED 10 watts lumen output of 1100 lumens batten aluminium extruded with decorative end caps complete all as specified and as directed. (Make- Bajaj Cat Part No BCLSB 10 NW or its equivallent model in Wipro, Philips, Havells).

S & F for Energy saving new generation 10 watts LED bulk head fitting IP 65 luminaire with opel diffuser pre wired with warranty option of 5 years from date of installation and necessary mounting arrangements , provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including LED bulb complete all as specified and as directed. (Make :- Havells/ Bajaj Cat No BIBWP 10W LED or its equvalent in Philips, Wipro)

S & F for wall mounted LED tube light fitting 18 to 20 watts batten with, system efficency >= 100 lumens/watts for surface mounted, anodized extruded aluminium housing, high transmissitivity diffuser, high lumen ouput box type fitting, 230 volts and intregrated electronic driver connector block etc with warranty option of 5 years from date of installation complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed. Make :- Bajaj Cat part No BCLAB 20W WH LED P, Wipro Cat part No LL20-281-XXX065-ALI or its equvalent in Philips, Havells.

S & F for Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 for security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 30 watts, system efficacy > = 110 lumen/watts, THD <10% and warranty of 5 years from date of installation with pre wired and necessary mounting arrangements and provision of 2.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as directed by Engineer- in-charge. (Make :- Wipro/Havells/Bajaj / Philips)

S & F for energy efficient exhaust fan of 230 mm sweep made of metal body Ventil Air -DS type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base compelte all as specified and directed. (Note : Cost of suitable opening wall for fixing exhaust fan incl making good of diturbed surfaces & painting to match with the existing surfaces is deemed to be included in overall rate quoted). Make: Havells/ Bajaj/ Crompton)

S & F for PVC non-metallic rigid conduit ISI marked heavy duty white/ Ivory colour and its accessories heavy duty ISI marked of size 20 mm dia for LAN, telephone and TV connections including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed.

Supply and fixing of Three Phase Electronic Energy Meter accuracy Class 1.0, 240V, with in-home display 10-60A, 3 Nos self locking meter seal, LCD diplay with optical port, anti temper features, LCD test ,serial no, Date, RTC,Cumulative Kwh, Last bill Kwh, Instanteous Load, Last bill MD, Instantaneous KW,Volts,PF,HZ, MD, total Tamper Count, Self Billing Code, Battery backup in absence of power for display active energy kwh, including all incoming and out goinig connections.- 04 Nos incl meter protection box made out of GI Sheet 2mm thick of suitable size to accommodate 3 phase meter with suitable locking arrangements and operator door, providing glass view for meter display painting with metallic paint over a coat of red oxide primer incl making good disturbed painting to match with existing surface (Make- L&T, Cat No:WM301BC7D10 / Secure/Havells)

Supply, installation, commissioning and testing indoor type LT wall mounting Panel Board of minimum size 1.00 m (height) x 1.00 m (breath) x 0.30m (depth) factory made CPRI approved panel, weather, dust & vermin proof indoor, double door, front openable, including four comparment for fixing of five Nos single phase meter and MCB and porviding glass view for reading of meter and providing rubber/ PVC gasket of suitable size all sides of door, with copper busbar wrapped with PVC tape/sleeves with maintained the colour code and copper strip/wire busbar of suitable size to MCCB input and MCCB/MCB output of suitable length for connection of cable from main busbar, made out of 2.00 mm thick mild steel CRCA sheet with suitable size angle iron supporting frame including applying two coats of Powder coated paint over a coat of red oxide zinc chrome primer over exposed external & internal surfaces suitable for 3 phase 4 wire system 415/440 volts grade including complete internal wiring with 1.5 sqmm copper wire and connections of all outgoing / incomming existing cable of any size complete all as directed by Engineer-in-Charge. (JCO, OR, Civilian Md Accn)

OUTGOING :- (a) MCB, Single pole & neutral, 40 amps, 240 volts, ‘C’ curve, 10 KA all complete as specified and as directed - 05 Nos (b) Fixing only serviceable existing electric meter- 05 Nos (obtained from taking down item)

Taking down existing old Extg unserviceable LT UG/ service cable of any description and size complete all as specified and directed.

Excavation in trenches not exceeding 1.5 metre wide & not exceeding 1.5 meter in depth for foundation ,laying of cable or pipe ( where provide for protection of cable or fixing poles and stay and getting out in soft/loose soil including trimming the sides and forming bottom surfaces to required levels complete all as specified and as directed by Engr-in-charge.

Returning, filling in trenches in soft/loose soil in layers n.exc. 25 cm after laying of cables including spreading, levelling, and well ramming complete all as specified and directed.

Removing surplus excavated soil to a distance n.exc. 50 metre and depositing where directed at a level n.exc.1.5 metre high from the starting point.

Material and labour for approved river sand cushioning for under ground cable in trenches 8 cm before laying and 15cm after laying of cable and punned thickness of sand shall be measured and paid for 18 cm only after punned /consolidated thickness complete all as specified and directed.

Supplying and laying un-reinforced precast concrete cable cover, class LV, Type-1, flat,size 250mm x 150mm x 40mm, ISI marked, laid flat across the cable length for cable protection embossed with LT 1100 Volts electric on the top surface complete all as specified and directed. (Make: Mahtab tiles / Alankar Tiles/Pearlers Industries/SIND Mozaic Gujrat/JJ Concrete Lucknow).

Supply and laying galvanised iron pipe 'light Grade' 40 mm in trenches , under floors, roads, along poles for protection of cables with all necessary fittings, including sealing ends complete all as specified and directed . (Make Jindal/Prakash Surya/Tata)

Supply and laying galvanised iron pipe 'light Grade' 25 mm in trenches , under floors, roads, along poles for protection of cables with all necessary fittings, including sealing ends complete all as specified and directed. (Make Jindal/Prakash Surya/Tata)

Boaring holes horizontally under Road without damaging the surface of road (minimum 1.0 Mtr below the road surface with the help of GI tubing of anydia not exceed 80 mm bore for passing of UG cable all as specified and as directed (GI pipe laid shall be measured seperately).

Supply and laying & testing and commisioning LT underground cable 1100 volts grade, XLPE insulated and PVC sheathed heavy duty armoured with multi staranded aluminium conductor laid in pipes, trenches/ducts, on poles etc of size 3.5 core x 35 Sqmm complete all as specified and directed

Supply and laying & testing and commisioning LT underground cable 1100 volts grade, XLPE insulated and PVC sheathed heavy duty armoured with multi staranded aluminium conductor laid in pipes, trenches/ducts, on poles etc of size 4.0 core x 16 Sqmm complete all as specified and directed

M & L for earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground vertically (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.50 mtr deep below normal ground level, connecting to GI earth wire 4mm dia by means of bolts, nuts, check nuts, and washers of galvanized iron or steel connected to earth test point including 15 mm dia. medium grade protection pipe for earth lead complete with charcoal and common salt including watering arrangement with galvanized iron pipe light grade 20 mm dia, PCC Chamber, CI frame and cover, MS funnel with wire mesh all as shown in electrical plate no 3 of SSR part I including excavation and earthwork in any type of soil/strata and testing on completion. Note :- GI earth wire 4 mm dia and 15 mm dia protection pipe upto 7.5 mtr from earth plate is deemed to be included in rate quoted.

m/s jethanand bhatia

M/S Umashanker Mishra