Loading
Loading…
Loading…
Tender Value
₹2.0 Cr
EMD Value
₹2.5 L
Closing Date
28 Jan 2026, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
Above/Below/Par
SIG/NORTH
14 conditions · 2 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or V whichever is less ;where V= Advertised value of the tender in crores of Rupees N=Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, asper the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information asper format-6, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
The tenderer must have successfully completed or substantially completed any one of the following categories of work(s)during last 07 (seven) years, ending last day of month previous to the one in which tender is invited:(i)Three similar works each costing not less than the amount equal to30% of advertised value of the tender, or (ii)Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii)One similar work costing not less than the amount equal to 60% of advertised value of the tender.
Defination of Similar Work :- Any signaling work involving outdoor work and / or addition and /or alteration in existing Indoor signaling system. OR any CLS or RI or EI or TPWS or IBS or ABS or BPAC work involving indoor and/or outdoor. Similar work to include indoor if the tendered work involves addition and / or alteration in existing indoor signaling system and outdoor if the tendered work involves outdoor work. OR Any such work involving activities as given in the name of the tendered work.
14 conditions · 5 needing a document upload
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
The tenderer shall clearly specify whether the tender is submitted on his own or on behalf of a partnership concern. If the tender is submitted on behalf of a partnership concern, he should submit the certified copy of partnership deed (PD) along with the tender and authorization to sign the tender documents on behalf of partnership firm. If these documents are not enclosed along with the tender documents, the tender will be treated as having been submitted by individual signing the tender documents. The tenderer whether sole proprietor, a limited company or a partnership firm if they want to act through agent or individual partners should submit along with the tender or at a later stage, a power of attorney(POA) duly stamped and authenticated by a Notary public or by Magistrate in favour of the specific person whether he or they be partners of the firm or any other person specifically authorizing him or them to submit the tender, sign the agreement ,receive money, witness measurement, sign Measurement Books, compromise, settle, relinquish any claims preferred by the firm and signed No claim certificate and refer all or any dispute to arbitration.
Tenderer should clearly state the status of firm and submit the relevant document in support of authentication, in absence of following/relevant documents the offer of tenderer is summarily rejected: (A)Self-declaration /proprietorship certificate in case of proprietor firm along with POA if any. (B) Partnership deed and power of attorney in case of partnership firm. (C)Certified copy of an extract of resolution passed by the board of directors in case of limited firm or Private Limited Company
(a) Sole Proprietorship Firm: (i)All documents in terms of Para 10 of the Tender Form (Second Sheet)of Tender document
(b) HUF: (i)A copy of notarized affidavit on Stamp Paper declaring that he who is submitting the tender on behalf of HUF is in the position of 'Karta' of Hindu Undivided Family (HUF) and 1.1.2 he has the authority, power and consent given by other members to act on behalf of HUF. (ii)All other documents in terms of Para10 of the Tender Form (Second Sheet)of Tender document
(c) Partnership Firm: (i)All documents as mentioned in para18 of the Tender Form document
(d) Company registered under Companies Act2013: (i)The copies of MOA (Memorandum of Association) / AOA (Articles of Association) of the company (ii)A copy of Certificate of Incorporation(iii)A copy of Authorization/Power of Attorney 1.1.4 issued by the Company (backed by the resolution of Board of Directors) in favour of the individual to sign the tender on behalf of the company and create liability against the company. (iv)All other documents in terms Para 10 of the Tender Form (Second Sheet) of Tender document
(e) LLP (Limited Liability Partnership): (i)A copy of LLP Agreement (ii)A copy of Certificate of Incorporation (iii)A copy of Power of Attorney/Authorization issued by the LLP in favour of the individual to sign the tender on behalf of the LLP and create liability against the LLP. (iv)An undertaking by all partners of the LLP that they are not blacklisted or debarred by Railways or any other Ministry / Department of the Govt. of India from 1.1.5 participation intenders / contracts as on the date of submission of bids, either in their individual capacity or in any firm/ LLP or JV in which they were/ are partners/members. Concealment /wrong information in regard to above shall make the contract liable for determination under Clause 62 of the Standard General Conditions of Contract.(v)All other documents in terms of Para 10 of the Tender Form(Second Sheet).
(f) Registered Society & Registered Trust: (i)A copy of Certificate of Registration (ii)A copy of Memorandum of Association of Society/Trust Deed (iii)A copy of Power of Attorney in favour of 1.1.6 the individual to sign the tender documents and create liability against the Society/Trust. (iv)A copy of Rules & Regulations of the Society (v)All other documents in terms of Para 10 of the Tender Form (Second Sheet) of tender document
Information as per Para 16 of GCC Part (1)(Tender form second sheet Annex-I) related to Employment/Partnership Etc. of Retired Railway Employees and Clauses 59 (9) & 62 (1) (xv) to GCC regarding employment etc. Of retired government officers by railway contractors
Certificate of Information regarding EMPLOYMENT/PARTNERSHIP etc. of Retired Railway Employees with the tender as per the attached proforma, Format 11 of tender document
Certificate of NO RELATIVE being an employee of Western Railway as per attached Performa Format10 of Tender document
Signalling work in connection with Improvement & Upgradation of Yard at VYARA & UKAI SONGADH under ADEN / VYARA jurisdiction of Udhna-Ukai Songadh Section of Mumbai Division, Western Railway.
SG_216_2_145_WA~WR
SG_216_2_145_WA
Open
Works - General
6 Months
Mumbai, Maharashtra
₹0
₹2.5 L
28 Jan 2026
29 Dec 2025
14 Jan 2026
200 items across 2 schedules
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 52,82,615.32 | ||
| — | 600.00 | — | — | ||
| G.I. Bonding wire soft for track circuit bonding 8 S.W.G.(4mm Dia.) or as per instructions of EngineerIn-Charge. | — | — | — | 40,902 | |
| — | 4000.00 | — | — | ||
| Channel Pins MS(Galvanized) single roove, 7 mm suitable for 4mm dia bonding wire as per spec No IRSS 17 & RDSO Drg No. S-69/M. | — | — | — | 24,160 | |
| — | 450.00 | — | — | ||
| Drill bits 7.2 mm or as as per instructions of Engineer In-Charge. | — | — | — | 40,428 | |
| — | 3000.00 | — | — | ||
| Copper Lugs 16 to 25 Sqmm for power cable or as per instructions of Engineer In- Charge. | — | — | — | 28,650 | |
| — | 4.00 | — | — | ||
| PVC Jacketed wire rope for track lead connections. PVC jacketed wire rope should be of Galvanized steelwire rope 6mm dia (6x19 stranded wire with steel core of 6 mm dia) sheathed with PVC 2mm wall thickness, overallthickness being 10mm. PVC sheath should be made of type 6 compound as per IS 5831 of 1970.Reclaimed or recycledmaterial should not be used. 100mts bundle required. | — | — | — | 22,212.68 | |
| — | 4.00 | — | — | ||
| Ground connections, complete set suitable for IRS type/approved TWS point Machine 220mm with hot dip galvanised. | — | — | — | 1,77,304 | |
| — | 20.00 | — | — | ||
| Contractor Unit Assly CU Base Assly 851241034-S, RDSO Drg.No. RDSO/S 10911, CG Drg.No.CHS-10911. | — | — | — | 2,43,108.4 | |
| — | 10.00 | — | — | ||
| Transparent cover sub assembly complete with Cover support LH RH, 853087001-S as per RDSO,approved CG drg. No. CSQ-10920 10915. | — | — | — | 3,681.6 | |
| — | 20.00 | — | — | ||
| Terminal Bank Assembly complete, 855032009-S as per RDSO, approved CG Drg. No.CPME-1124. | — | — | — | 39,270.4 | |
| — | 10.00 | — | — | ||
| Waterproof Galvanized MAIN COVER ASSEMBLY complete spare for POINT Machine comprising of Maincover, CRANK HANDLE HOLE SUB. ASSY, KEY HOLE LOCK SUB. ASSY, DOOR LOCK, RUBBER GASKET of MAIN COVERASSY, Rubber GASKET (C.H. HOLE LOCK ASSY.), CRANK HANDLE HOLE LOCK BASE, CRANK HANDLE HOLE LOCK LID,PIN (for C.H. HOLE LOCK S/A), RUBBER GASKET (C.H. HOLE LOCK ASSY. LOCKING CAM, KEY code 856051010-s alongwith Fixing material to trap accumulated air as per Drg no R-ST- 12161, modification in cover as per consigneerequirement. Thickness of cover material:- 2mm, galvanizing and power coating shall be done on cover. (InspectionAgency-RITIES/Consignee) | — | — | — | 1,72,114.8 | |
| — | 50.00 | — | — | ||
| Switch Plate lubricant Cenolube 100 or better NLGI 1.5 GRADE Black colored Grease which should be non asphaltic Non bituminous blend of very heavy oils, inert thickeners and lubricating solids coupled with molybdenum disulfide and graphite with no traces of chlorinated solvent such as 1,1,1 trichloroethane which are flammable and harmful to the environment. Should have a blend of select high viscosity index solvent refined severely hydrofinished paraffin base oils and synthetic base fluids. It should incorporate solid lubricants &additives to fill & lubricate micronized asperities to provide & form many films on the contact surfaces to prevent metal-to- metal contact. It shall be designed to be hand applied providing a tough adherent Lubricant film with Tacky semi-dry finish reducing contaminant adhesion. It should act as a SURFACE POLISH with high shear stability and UV protection. The grease Should Not form a difficult to remove thick DRY film which requires scrapping & solvent cleaning of Switch Plate specially before reapplication The grease should Not need Cleaning or scrapping before Reapplication. The Grease should be formulated for tropical climates and should not contain pour point depressants and should Not be too thin. The grease shall be Resistant to water wash off & dilution, water insoluble, non-melt and chemically resistant to exposed environment. The grease shall be formulated with Extreme Pressure additives, rust and corrosion inhibitors, anti-wear additives to protect external surfaces against the harsh elements in severe climates, thus reducing rust binding and adhesive wear on switch plates. Water washout-Excellent (ASTMD1264) <1% ASTM D4049 -water Spray Resistance (simulating rain).Minimal grease loss (<10%) under high-pressure water spray.(ASTM G154 )- UV Resistance (Fluorescent UV Light Exposure- Gloss retention of 90% or higher after 1,000-2,000 hours of exposure. Four Ball Weld LOAD (ASTM- D2596) >600 Kg, Copper corrosion 24 hrs. @ 100c (ASTM D 4048) 1a -1b,(ASTM D4289) - Compatibility with Rubber SealsMinimal swelling (<5% change in volume). No softening or hardening (<10% change in hardness). No cracking or surface degradation. packing /25kg Drum. /180 kg drum Inspection by RITES with GCTC from NABL accredited lab . | — | — | — | 2,47,500 | |
| — | 20.00 | — | — | ||
| Supply of Nylon Insulation for Thick Web point machine, consist of Insulating. (1) plate- 02 Nos . as per RDSO Drg. No-S-34041(2) Nylon Insulation bush-8 Nos , as per RDSO Drg. No- (a) S32199-04 Nos . (b) S-8813-04 Nos , (3) Nylon Insulation Washer 08 Nos, as per RDSO Drg. No. (a) S8640/1-04 Nos . (b) S-8640- 04 Nos. 2) Through rod Insulation = 1 no Bush(RDSO Drg No. CSE8640/1, 2 nos Washers (CSE8640/2) 3) Lock slideInsulation -2 nos Bushes (RDSO Drg No- CSE 8640/A) 4 nos Washers (RDSODrg No. CSE-8640/1). 4) Detection slide insulation =2 nos Bushes (RDSO Drgno. 8641/A), 4 nos Washers (RDSO Drg No-8640/1). 5) SSD Insulation Rod =1no. Plate (RDSO Drg No S325/M), 2 nos . Bushes (RDSO Drg No-T10372), 4nos. Washers (RDSO Drg No T- 10371). 6) SSD Insulation in Rail 1 no . Washer(RDSO Drg No washer : S8640) 1 no Bush (RDSO Drg No S8641/A) 7) Pbracket Insulation :- Insulation Plate 01 (RH) RDSO Drg No: S3265 Insulation Plate = 01 No (LH) RDSO Drg no. S3266 , Insulation Bushes=04 nos. RDSO Drgno S23199 Insulation Washer : 04 nos . RDSO Drg no. S8640. | — | — | — | 19,918.4 | |
| — | 600.00 | — | — | ||
| PVC tube for bootleg outside dia 15mm, inside dia 11mm thickness 2 mm 50 mtrs each coil. | — | — | — | 5,172 | |
| — | 2.00 | — | — | ||
| Supply of Digital Insulation Tester 100V/250V/500V range of Model Rish insu 20 Make :RISHABH or MECO or similar. | — | — | — | 16,480.8 | |
| — | 2.00 | — | — | ||
| Digital low current clamp meter to measure current leaks (parasitic draw down to 1 mA) and electric loads from 1mA to 100 Amp AC/DC, Voltages from 0 to 600V AC/DC, small jaw size to measure current in signalling circuit, 4 digit display. Make -Fluke, GTC/KEW, Scope or superior with better specification as mentioned with all accessories like test lead, batteries and carrying case, sample may be got approved from consignee before supply. | — | — | — | 36,388.68 | |
| — | 2.00 | — | — | ||
| Professional AC/DC clamp meter 3 ¾ digit, true RMS measurement, For Measurement of DC/AC currents up to 1000A, Voltage up to 600V, resistance up to 40 M, and frequency up to 1 MHz with a set of leads & carrying case. Model - DCM39A or equivalent/ higher make Motwane /Stanley /Fluke/ Megger. | — | — | — | 25,707.18 | |
| — | 2.00 | — | — | ||
| Supply of Digital Earth Resistance tester three terminal type with LED display, 1999 count, KOICO model 5600 or any reputed make approved by engineer in-charge. | — | — | — | 26,713.68 | |
| — | 2.00 | — | — | ||
| Road Measuring Cycle, made of Aluminum with 05 digit counter, foldable with the bag. | — | — | — | 9,031.68 | |
| — | 2.00 | — | — | ||
| Radiodetection Precision Pipe and Cable locator / Route tracer Brand: Radiodetection (Detailed Description/Specification as per Product # 1 of GeM Contract No. GEMC-511687782278007 dt.21/02/2025) | — | — | — | 9,99,990 | |
| — | 2.00 | — | — | ||
| Battery operated Rail core drilling machine with quick action clamping system on track along with 18 mm TCT rail core drill. Maximum core cutting capacity 36 mm, rated speed 250/450 RPM. Battery type Lion, Battery voltage 50V, battery pack capacity 4AH. Number of batteries supplied- 2 Nos with suitable charger 1 no. Special designed pressurized internal spindle cooling to give maximum life of core cutter by avoiding heating. 3 sets of 22, 13, 16, 7.2 gauze drills adapters to be provided along with the machine. Weight of the machine 18.5 kgs maximum. Make- Eibenstok, Bosch, KPT with all accessories suitable for the Railway Signalling and along with carrying case. | — | — | — | 2,25,696.24 | |
| — | 2.00 | — | — | ||
| Canon A3, A4 and LegalColour Laser ComputerPrinter cum scanner ofreputed make as pertechnicalspecification.Model may be got apprvoedfrom Railway in-chargebefore supply of material. | — | — | — | 4,30,198 | |
| — | 4.00 | — | — | ||
| Main Signal Post Tubular 140 mm Dia, 5.6 Mtr Length as per IRS: S-6/81 or Latest & RDSO Drg. No. SA-24625 (Advance). (ALL MS PARTS HOT DIP GALVANIZED -100 MICRON) | — | — | — | 43,581.64 | |
| — | 4.00 | — | — | ||
| Supply of 1. CI Base (As per IRS S-10 & RDSO Drg. No. 2011/M With latest assembly).2. Pinnacle.3. Ladder Assembly, as per RDSO Drg. No. SA-23156, with Base, Ladder Guards, Platform, Front Maintenance Platform, MS Supporting bracket to Support Ladder.4. Signal Front Staging Complete Assembly for CLS Unit.5.Signal back staging as per extent WR Practice. | — | — | — | 13,005.32 | |
| — | 4.00 | — | — | ||
| Signal Number Plate (CSTEDrg No CSTE/6186) All material required for this work shall be supplied by thecontractor. Material used for number plate should comply with the specification ETI/OHE/33A(12/97) Rev-8. CSTEdrawing is to be followed for dimensions only. | — | — | — | 2,462.36 | |
| — | 2.00 | — | — | ||
| Offset brackets for Main Signal, made of tubular steel, outer diameter 140 mm, thickness of pipe 4.5mm. horizontal length of pipe 545 mm & vertical length of pipe 324 mm with fixing arrangement on Main Signal post asper Drawing No SW/554/G/R. | — | — | — | 8,878.56 | |
| — | 2.00 | — | — | ||
| 2 Aspect LED Signal Housing made of SS-304 (Min 1.6mm thick) duly powder coated in black, with background plates, prewiring for LED Signals, Terminal strip, Reflective strips on rear side, ventilation and Pole Mounting & locking attachment, suitable for RE area. The design shall confirm to IP-54 as per unit description as Width 260mm, Depth 200mm, Height 650mm as per Drawing No.- DRM/SG/1021(2A) of STAINLESS STEEL (SS- 304) 2 ASPECT COLOR LIGHT LED SIGNAL UNIT (LED lighting unit will be supplied by railway) | — | — | — | 57,155.44 | |
| — | 2.00 | — | — | ||
| 4 Aspect LED Signal Housing made of SS-304 (Min 1.6 mm thick) duly powder coated in black, with background plates, prewiring for LED Signals, Terminal strip, Reflective strips on rear side, ventilation, Pole Mounting & locking attachment, suitable for RE area . The design shall confirm to IP-54 as per unit description as Width 260mm, Depth 200mm, Height 1100mm as per Drawing No.- DRM/SG/1021 (4A) of STAINLESS STEEL (SS-304) 4 ASPECT COLOR LIGHT LED SIGNAL UNIT (LED lighting unit will be supplied by railway) | — | — | — | 66,607.72 | |
| — | 2.00 | — | — | ||
| Position Light Shunt Signal Unit Complete with Post (made of GI Pipe of 80 mm Diameter Medium ClassIS Spec. No. IS: 1239 Pt. 1/1990) Base, Hood, and Cover, etc. as per Drg. No. SA-23840, Signal Number Plate, suitablefor LED Signal Lighting Unit. (Supply of LED Unit is not covered in this item). | — | — | — | 9,060.14 | |
| — | 2.00 | — | — | ||
| Position Light Shunt Signal Unit Complete, with offset bracket, hood, Cover etc. as per Drg. No. SA-23840 suitable for LED Signal Lighting Unit. (Supply of LED Unit is not covered in this item). | — | — | — | 6,719.48 | |
| — | 4.00 | — | — | ||
| Supply of SS Location box made of SplGrade SS 304 of size as per drg. No.DRM/SG/945 (Half app. Case).Dimension of Case should be as perDRM/SG/945. It includes Angle frameRelay frame fixture , earthing Rod ,Drawing Board, Glass ReinforcedPolyester Sheet Moulding Compoundssheet for fixing ARA terminal, Lock etc.as per WR CSTE Drg No. 6285.Manufacturer's certificate in regard tograde of stainless steel and test reportshall be submitted at the time of supply.Inspection by RITES. | — | — | — | 2,07,992.24 | |
| — | 4.00 | — | — | ||
| Supply of Modular Location Box as perWR CSTE Drg No. 6285 Modular Type SS304 Full Location Box. It includes Angleframe Relay frame fixture , earthing Rod, Drawing Board, Glass ReinforcedPolyester Sheet Moulding Compoundssheet for fixing ARA terminal, Lock etc.as per WR CSTE Drg No. 6285.Manufacturer's certificate in regard tograde of stainless steel and test reportshall be submitted at the time of supply.Inspection by RITES | — | — | — | 3,49,809.32 | |
| — | 8.00 | — | — | ||
| IS 13410: Glass Reinforced Polyester Sheet Moulding Compounds (SMC) Size of Sheet : 1000x1000x8. | — | — | — | 43,109.36 | |
| — | 2400.00 | — | — | ||
| Disconnect Terminal Block, Screw RDSO/SPN/189/2004. With the latest amendments. | — | — | — | 1,40,472 | |
| — | — | — | RDSO | ||
| — | — | — | Spec. | ||
| — | 240.00 | — | — | ||
| Supply of End plate 2.5mm/0.091 in thick as per site requirement. | — | — | — | 2,656.8 | |
| — | 480.00 | — | — | ||
| Supply of End Stopper 10mm/0.0394 in width as per site requirement. | — | — | — | 5,212.8 | |
| — | 70.00 | — | — | ||
| Supply of Carrier Rails for above 35mm x 7.5mm, 1mm/0.039 in thickness un-slotted type as per site requirement. | — | — | — | 7,971.6 | |
| — | 60.00 | — | — | ||
| Maintenance Free EarthElectrode of length 3m,including supply of 3 bags ofEarth enhancement material forearthling (10KGs/bag) for eachelectrode & other accessoriesas per Drg. No. SDO / RDSO/E&B/001 and RDSO Spec No.RDSO / SPN/197/2008. Thisitem includes the followingitems: (a) Copper bonded steelearth electrode of 3.0 meterlong & 17.2 mm dia with Cu- bonding thickness of min 250micron - 1 no. (b) Earth-enhancing compound (10Kg/Bag) - 3 No. (c) Cu- strip200 X 25 X 6 mm to terminateearth rod = 1no. (d) Cu-strip300 X 25 X 6 mm (MEEB) = 1no. (e) Cu-strip 150 X 25 X 6mm (SEEB) = 1 no. (Inspectionby RDSO) | — | — | — | 6,24,184.8 | |
| — | 60.00 | — | — | ||
| Supply of Fiber/SMC/FRP/RCCEarth Chamber asperinstructions of EngineerIncharge as per site requirementas perSTS/E/TAN/3006 ver 3.0 | — | — | — | 38,940 | |
| — | 40.00 | — | — | ||
| Supply of Copper Bus Bar 200 x 25 x 6 mm SEEB to terminate earth rod. | — | — | — | 13,216 | |
| — | 40.00 | — | — | ||
| Supply of Copper Bus Bar 150 x 25 x 6 mm SEEB. | — | — | — | 10,384 | |
| — | 40.00 | — | — | ||
| Supply of Copper Bus Bar 300 x 25 x 6 mm MEEB. | — | — | — | 16,048 | |
| — | 200.00 | — | — | ||
| Supply of Copper strip of 25 x 2mm for interconnectiing of earth pits. | — | — | — | 1,15,640 | |
| — | 100.00 | — | — | ||
| Supply of 35 Sq mm maulti strand signle core PVC insualted copper cable for connecting earth bus bar to earth electrode. | — | — | — | 42,252 | |
| — | 2400.00 | — | — | ||
| ARA Terminal blocks with links made of PBT Spec No.s/75/2006 (Rev - 2) with latest amendments and RDSO Drg.No.SA-23741A Alt.4. | — | — | — | 1,80,000 | |
| — | 400.00 | — | — | ||
| High density polyethylene pipes (HDPE) of 110 mm/125 mm outer Dia, 10 mm wall thickness, along with one coupler for every 6 Mtr. As per spec. No. Is 4984:2016 with latest amendments and material grade: PE 80. | — | — | — | 2,80,400 | |
| — | 20.00 | — | — | ||
| Double Walled Corrugated (DWC) HDPE Pipe with associated collars etc. as per RDSO Specification No. RDSO/SPN/204/2011 or latest anti-rodent & anti-oxidant and non-flame propagating type in 6 meters straight length and of size 120 mm outer die,& 103.5 mm inner dia. . One of the following coupling arrangements should also be supplied with each pipe as per the site requirement. 1) Suitable snap fit coupler with rubber 'O-Ring 2) Spacers 3) Tees 4) Bend, 5) End-cap (The total quantity of above items is equal to no. of pipes supplied.) DWC pipe shall be marked at every 1 mtr length in such a way that manufacturer's name, vender name and year of manufacture can be easily identified. Color -Bright Orange; Test Check by Consignee & Sample check by JAG officer. | — | — | — | 38,244 | |
| — | 40.00 | — | — | ||
| — | 2.00 | — | — |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
TD145VYAUSD.pdf
ATTACHMENT
TD145VYAUSD.pdf
CORRIGENDUM
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .