Providing Audio and Video systems, furniture arrangements and improvements works to the conventional centre

Amount

Supply and installation of Full Range modular line array speakers Freq Response 80 Hz–20 kHz (-10 dB) Dual 8-inch LF drivers and 3-inch titanium compression driver 110° horizontal x 12° (variable) vertical dispersion 136 dB maximum SPL., Variable inter-box anglesI/O: two 4-pole NL4 connectors wired in parallel , Make : JBL

Supply and Install of dual 15" Sub with Dual 15-inch woofers Frequency range: 32 Hz–250 Hz (-10 dB)136 dB maximum SPL,Built-in DSP includes crossover management, EQ, limiting, correction filters, phase-corrected processing and driver-protection circuitry Integrated 1,000 watt-per-channel, 6-channel amplifier. , Make : JBL

Supply and fixing of JBL Line array Bumber to max 8 nos of 308 Tops or one 325 Sub incluidng all cost etc complete.

Supply and Installation of 12inches Active wedge monitor 2-way, Bi-amped Powered Speaker, Bass-reflex , Frequency range (-10dB) 55 Hz - 20 kHz,Maximum Output Level (Measured peak, IEC noise@1m) 129 dB SPL

Supply and Install of 10Inches Active speaker , 2-way, Bi-amped Powered Speaker, Bass-reflex Frequency range (-10dB) 52 Hz - 20 kHz,Dynamic 700 W Processors HPF: OFF, 100 Hz, 120 Hz, 24 dB/Oct

Customised Yoke bracket for front fills, Gallery, FLYING Stack Speakers and Under gallery fills etc completd.

Supply ,installation of Audio DSP with router and signal processor 2in 8out etc completd.

Supply and Installation of 15 Inches Flying Stack speakers, Self Powered 15”, two-way,Maximum SPL (1m) Normal: 137 dB Boost: 137 dB , Frequency Range (-10dB) Main: 42.9 Hz - 19.5 kHz Monitor: 43.6 Hz - 19.3 kHz,Crossover Frequency 2 kHz, Power Rating 1500W (750W x 2), AC power input 100V - 240V ~ 50/60 Hz,LF Driver 1 x JBL 275G (15 in) woofer HF Driver 1 x JBL 2408H-2 37.5 mm (1.5 in) annular polymer diaphragm, neodymium compression driver, Coverage Pattern 90° x 50° nominal Directivity Index (DI) 10.2 dB, Directivity Factor (Q) 10.4Make : JBL

Supply and install of Yamaha 32 Channel Mixer with effects

Supply and Fixing of 10 Channel power conditioner 10 A Make : Furman

Supply and Install of Krycard 20KVA 1PH AIR cooled Servo stablizer with input voltage range (170V-270V) Make : Krycard

Providing of Calibration, installation and programming Charges etc completed.

Supply nad fixing of AV Rack with Mixer holder 1 unit etc completded.

Providing of Cables connectors, IEC sockets and and accessories Make: Beldon, Havells, Neutrik, including labour charges etc complete.

Supply and Installation of P 1.8 Qiangle Indoor LED Video wall Dimensions 30.4ft (W)x16.8 ft (H) With Nova Star 4K support video Processor , with Fitting and fabrication , Refresh rate ≥3840 hz

Supply and Installation of Krycard 30KVA 3PH AIR cooled Servo stablizer with input voltage range (360V-460V)

Providing of 30.4ft (W)x16.8 ft (H) Belden Cables connectors, Havells IEC and necessary accessories, Conduits as per the site

Supply and Installation of P 1.8 Qiangle Indoor LED Video wall Dimensions 24ft (W)x13ft (H) With Nova Star 4k video Processor , Fitting and fabrication, Refresh rate ≥3840, of an approved brand and quality etc complete.

Supply and fixing of Krycard 20KVA 1PH AIR cooled Servo 24ft (W)x13ft (H)stablizer with input voltage range (170V-270V) of an approved brand and quality etc complete.

Providing of 24ft (W)x13ft (H) Belden Cables and connectors and patches,Installation and calibration charges.

Supply and Fixing of 100W LED PARCAN Light, 3200K, 9°-30° Manually adjustable, manual / DMX control, fully RDM compliant when in DMX mode, Light output @ 2 Mtr >35,000 lux at spot mode, Spun Aluminum housing with black powder coated with matt finish. Model : CAN LED PARCAN Make : Canara Lighting

Supply and Fixing of 400W LED Blinder Light, 3200K, 40°, manual / DMX control, fully RDM compliant when in DMX mode, Light output @ 2 Mtr >8,000 lux, MS housing with black powder coated with matt finish. Model : CAN LED BLDR 400 Make : Canara Lighting.

Supply and Fixing of 54 x 3W RGBW LED PAR Light, 15°, Manual / DMX control, fully RDM compliant when in DMX mode, Light output @ 2 Mtr >10,000 lux, Die casted Aluminum housing with black powder coated with matt finish. Model : CAN LED PAR 543 Make : Canara Lighting

Supply and fixing of 200W LED Profile Light, 3200K, 19° beam angle, manual / DMX control, fully RDM compliant when in DMX mode, Light output @ 2 Mtr >20,000 lux, PVC or Aluminium housing with black finish. Model : CAN LED PRO 219 Make : Canara Lighting.

Supply and Fixing of 150W LED Moving Head with beam effect, color wheel, Gobos, Prism, manual / DMX control, fully RDM compliant when in DMX mode, Light output @ 2 Mtr >60,000 lux at spot mode, Engineered plastic & alloy housing with black finish. Model : CAN LED MH 150P Make : Canara Lighting.

Supply and Fixing of Premium quality LED PAR Light with latest RDM technology for user friendly operation with below specifications: Base Color 3200K Color Mixing LED Configuration: Multiple Nos Individual 3200K LED Configuartion Power cable: 3 core 1 sq. mm. copper PVC insulated Channels: 1 DMX-512 Beam angle: 15° Control mode: RDM, DMX512 & Manual Fully RDM Compliant in DMX Mode for the Lighting Console mentioned in this project.Model : CAN LED PAR 543T Make : Canara Lighting.

Providing of Lighting bar over stage area consists of : - 1. Fixed FOH Light Bar #32. Fixed Stage Light Bar #6Model : Custom.

Supply and Fixing of Diecast Aluminium C Clamp for all Lights, Safety bond for all Lights ,Identification name plate Model : ACC-10, SB-15, INP-79

Supply ,Installation of RDM Compatible Digital Lighting console with Minimum following specifications. 1024 Channel, 2 Universe, No. Of Direct Fixture Control : Atleast 96, No. Of Faders : Atleast 16, No. Of Submasters : Atleast 10, Atleast 3 Encoder Wheels, LCD Display for Navigation, Should support ART-NET Port, Fully RDM Compiant in DMX Mode Make : Canara Lighting.

Supply and Fixing of Power control system consisting of Direct Lighting Distribution Board for all the lighting points with necessary Indicators and safety controls. Power Junction boxes for Lights, Splitter & console etc & Internal earthing system & installation Hardwares required for successful installation. Make : Canara Lighting

Supply and Fixing of Digital Dimming DMX Network for the LED Lights including DMX Splitter for the Light dimming network, DMX dimming junction boxes, Loop box for the dimming network, XLR connectors and Termination plugs.Make : Canara Lighting.

Wiring of Stage luminaries using 3core 1.5sq.mm FRLS flexible power cables & DMX signal cables run inside the MS perforated cable trays with termination at the Power distribution centre panel for all points.

Supply and fixing Shure MX418 D/C of an approved brand and quality etc complete.

Supply and fixing Shure BLX 24 IN / PG58 Mic of an approved brand and quality etc complete.

Supply and fixing Shure BLX 14IN / Lavelier Mic of an approved brand and quality etc complete.

Supply and fixing 4 Channel Audio TX Over Shielded CAT 6 of an approved brand and quality etc complete.

Supply and fixing 4 Channel Audio RX Over Shiielded CAT 6 of an approved brand and quality etc complete.

Supply and Installation of 16 Channel Mixer with effects

Supply and Laying of Belden Microphone Cables Neutrik connectors, Conduits as per the site requirements

Providig and fixing 50W Recess Round COB LED light 4K of an approved brand and quality etc complete.

Providig and fixing 14.4W Out door LED Strip light of an approved brand and quality etc complete.

Providig and fixing LED Neon Flexi Connector Luker LS of an approved brand and quality etc complete.

Supply and Fixing of L&T / ABB Make Distribution Boards , MCB , RCB for the main hall as per the site requiremnent

Laying of electric wires for cob lights, Strip lights , audio and video with necessary sockets and switches for the auditorium as per the site requiremnent

Earthing arrangements with GI Earth Plate including charcoal and salt with necessary excavation in all soils and to full depth as may be required and masonry work, re-filling the sides of foundation with excavated earth as per the standard specification and as directed by the Departmental Officers.

Providig and Fixing of LED Surface Light fittings of an approved brand and quality etc completed

Providing of Side Wall Decorative Lights with wiring and labour etc completed

Providing of Exit light for 10 units with wiring and installation etc complete.

Providing of Step Light for 20 units with wiring and installation etc complete.

Providing and fixing Electrical provision for FOH Lighting with necessary Accessories etc complete.

Providing and fixing Electrical provision for Audio System with necessary Accessories etc complete.

Providing and fixing Electrical provision for LED Wall with necessary Accessories etc complete.

Providing and fixing 90mm thick Fixed wings which comprising of Aluminium frame @600mm c/c both ways up , comprising of 18mm to commercial ply (Green ply or equivalent) fixed on aluminium frame on both sides, finished with 1mm thick laminates of approved shade , including 50mm Anutone PolySynth of 1000 gsm shall be placed in the cavit. The wings to be fixed upto the false ceiling level of 6feet in width include all complete as per the drawings.

Providing and Fixing of Proscenium Panelling Works for the stage using One side teak wood sheet of 3.5mm thick will be fixed over the water proof plywood and finishing with wood putty and melamine polishing using the frame support

Providig and fixing of Seating Arrangments including all cost of materials and labour charges ,transportation etc complete.

Providing of VIP Seating Arrangements including all cost of materials and labour charges ,transportation etc complete.

Providing and fixing Acoustic Wall Panelling anutone make in channelled wood works perforated panels of width 192mm, thickness of 15mm and length of 2400mm or as per required by the Departmental Engineer made of a high density fibre board with minimum 725 kg./m3 density substrate with a laminated facing as per the approved shade and finish and a melamine balancing layer on the reverse side. The boards shall have a special peforation pattern where the visible surface has a "Helmholtz" fluted perforation of 3mm width and 21mm of visible panel Nos. The edges of the panels shall be "tongue-and-grooved" to receive special clips for installation. The back of the perforated panel shall have sound absorbing non woven acoustical fleese having NRC of 0.52. The panels shall be mounted on special aluminium splines using clips provided and approved by the Engineer-in-Charge

Supply and Installation of Perforated Acoustic Wall Panelling WhiteLock G.F Superfine ReInforced Gypsum with high durable grade ,fire retardant and sag free grade of Size 595 x 595mm x 12mm thick back lined with sound fleece . The panel should be fixed with G.I. channels of 50 x 25mm are fixed on the wall . The panel should be backlined with 50 mm 1000 GSM PolySynth adhered by using suitable method to give better NRC upto 0.8 - 0.85 and as directed as per the drawing . The perimeter , Intermediates and joiints is levelled with Gypsum Panels as per the design