CERTAIN SANCTIONED SPECIAL REPAIR, REVENUE AND MINOR WORKS AT MIRAN SAHIB UNDER GE JAMMU

Amount

B/R Portion: - Dismantling wall and ceiling boards (fibre, pulp, insulation etc), or insulation boards / slabs / blankets, any thickness any type including cover fillets complete all as specified and as directed.

Taking down chowkhats or frames not exceeding 1.5 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and as directed.

Taking down chowkhats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and as directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and as directed.

Material and labour for 10 mm thick rendering in cement mortar (1:6) on other than fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for 5mm thick rendering in cement mortar (1:3) on ceiling surfaces finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for rendering 15mm thick on fair faces of brick / concrete surfaces built in cement mortar (1:4), finished even and smooth with water proofing compound without using extra cement complete all as specified and as directed. Note: - Water proofing compound will be measured and paid separately.

Material and labour for preparation of surface and applying three coats of white wash on newly plastered surface of ceiling complete all as specified and as directed.

Material and labour for preparation of old plaster or painted surfaces of ceiling and applying two coats of white wash complete all as specified and as directed.

Material and labour for preparation of new surface and applying two coats of oil bound distemper new plaster surface over 1 mm thick putty complete all as specified and as directed.

Material and labour for complete removal of existing surface and preparation of old surface and applying two coats of oil bound distemper over 1 mm thick putty complete all as specified and as directed.

Material and labour for preparation of new surface and applying two coats of exterior emulsion / weather proof paint over a coat of primer over and including 1 mm thick putty on plastered surface complete all as specified and as directed.

Material and labour for complete removal of existing surface and preparation of old surface and applying two coats of exterior emulsion / weather proof paint over a coat of primer over and including 1 mm thick putty on plastered surface complete all as specified and as directed.

Material and labour for rendering 20mm thick in cement mortar (1:4) on concrete surface such as chajjas, upward fascias, roof surfaces and similar items including two or more dubbing coat, surface finished even and fair without using extra cement including mixing of liquid waterproofing compound (Liquid water proofing compound shall be measured and will be paid separately) upto height of four storeyed building with all necessary formwork, scaffolding, lifting arrangement for external surface upto 4 storey buildings) complete all as specified and as directed by Engineer-in-Charge.

Material and labour for washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster (1:4) (1 cement : 4 coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster (1:1/2:2) (1 cement : ½ coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing the top layer with brushes and water to expose the stone chippings complete all as specified and as directed.

Material and labour for 75mm thick cement concrete (1:3:6) type C-1 (using 20mm graded crushed stone aggregate) as in floor / plinth protection laid in suitable panels finished even and fair. 6mm joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 85/25 or 80/100 grade and three parts of sand (all by weight) complete all as specified and as directed.

Supply and fixing solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tube, supplying and fixing in opening as per specification and drawing complete all as specified and as directed.

Supply and fixing factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of mild steel tubes for top and bottom rails. Mild steel frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, Panelling of plain colour PVC sheet to be fitted in the mild steel frame welded / sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification complete all as specified and as directed.

Supply and fixing 100 mm size butt hinges medium weight cold rolled mild steel complete all as specified and as directed.

Supply and fixing 35 mm thick plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I) kiln seasoned complete all as specified and as directed.

Supply and fixing 35mm thick second class hard wood factory made glazed and skeleton shutters, open, rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part - I, Section 8, clause 8.20 (a) complete all as specified and as directed.

Supply and fixing box type steel windows / Ventilator (factory made) outer frame made out of ERW tube 'P' section 65 X 45 X 25 mm and shutter of ERW tube 'P' section 50mm X 35mm X 20mm openable (double shutter) with glazed shutter on external side and gauzed shutter on internal side including steel pintel hinges steel handle 100 mm long mild steel tower bolt 02 no's on each shutter stopper of 'Z' section and its locking arrangement and mild steel hook and eyes suitable for fixing cooler / AC window complete all as specified and shown on drawings No CEPZTD-324/07 Sh 1/3 to 3/3 and as directed. Notes: - The quoted rates shall also include: - (i) One shop coat of zinc chromate primer on all exposed surface and one coat of tar on the ends of steel surface in contact with bricks / concrete surface. (ii) 4 no's MS steel lugs made of 20X5 mm Iron flat 200 mm long. (iii) 10 mm Sq Bar grill / guard bar design as per drawing. (iv) PCC block for embedding lugs. (v) Two coats of synthetic enamel paint. (vi) Galvanized mild steel wire clothes power woven 0.46mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed.

Supply and fixing pressed steel frames (factory made) made out of 1.25 mm thick black mild steel sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete size of frame 105 x 60mm including bottom of each chowkhat to be welded with 2 No's 25 x 25 x 3mm thick flat iron projecting 10 cm on either side complete all as specified and as directed.

Supply and fixing pressed steel frames (factory made) made out of 1.25 mm thick black mild steel sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete size of frame 125 x 60mm including bottom of each chowkhat to be welded with 2 No's 25 x 25 x 3mm thick flat iron projecting 10 cm on either side complete all as specified and as directed.

Dismantling wrought iron or mild steel work as in cooler stand etc. complete all as specified and as directed.

Supply and fixing mild steel framed works such as grills, framed guard bars, etc and similar work as in cooler stands etc. conforming to Fe 410-0 or Fe 310-0 complete all as specified and as directed.

Supply and fixing factory made single extruded WPC (Wood Polymer Composite) solid door / window / Ceosetory windows and other frames / chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of 'K' value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder / rice husk / wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 grams) fabricated with mitred joints after applying PVC solvent cement and screwed with full body threaded star headed stainless steel screws having minimum frame density of 750 kg / cum, screw withdrawal strength of 2200 N (Face) and 1100 N (Edge), minimum compressive strength of 58 N/mm², modules of elasticity 900 N/mm² and resistance to spread of flame of Class 'A' category with property of being termite / borer proof, water / moisture proof and fire retardant and fixed in position with mild steel hold fast / lugs / stainless steel dash fasteners of required dia and length complete all as specified and as per directions of Engineer-in-Charge. Notes: - (i) Mild steel hold fast / lugs or stainless steel dash fasteners shall be paid for separately. (ii) For WPC solid door / window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Supply and fixing modular auto concealed soft closed hinges 35mm, 110 degree size fixed to cupboard complete all as specified and as directed.

Supply and fixing in repair 18 mm thick factory made 100 % solid WPC flush shutter (for cupboard and vanity etc) made from co-extruded three layer rigid foam sheet (single extruded) with 0.8 to 1 mm thick outer layer having density not less than 1400 kg/cum and density of central core not less than 600 kg/cum manufacturer by an ISO 9001/2015 certified company complete all as specified and as directed.

Supply and fixing 18 mm thick factory made 100 % solid WPC flush shutter (for cupboard and vanity etc) made from co-extruded three layer rigid foam sheet (single extruded) with 0.8 to 1 mm thick outer layer having density not less than 1400 kg/cum and density of central core not less than 600 kg/cum manufacturer by an ISO 9001/2015 certified company complete all as specified and as directed.

Supply and fixing magnet catcher 50 mm size for kitchen cupboard shutter complete all as specified and as directed.

Supply and fixing stainless steel handle 100mm fixed to cupboard complete all as specified and as directed.

Supply and fixing 75 mm size butt hinges medium weight cold rolled stainless steel complete all as specified and as directed.

Material and labour for PCC (1:3:6) type C-0 (using 12.5 mm graded crushed stone aggregate) as in back filling, bed block for hold fast etc complete all as specified and as directed.

Material and labour for PCC (1:2:4) type B-1 (using 12.5 mm graded crushed stone aggregate) as in coping, benching on corner of joints, as in roof kerbs rounded or chamfered on edges etc complete all as specified and as directed.

Supply and fixing aluminium handles 'D' type anodised 150 mm long ISI marked complete all as specified and as directed.

Supply and fixing aluminium handles 'D' type anodised 125 mm long ISI marked complete all as specified and as directed.

Supply and fixing 150 mm long aluminium anodised barrel tower bolt of extruded section ISI marked complete all as specified and as directed.

Supply and fixing 200 mm long aluminium anodised barrel tower bolt of extruded section ISI marked complete all as specified and as directed.

Supply and fixing 300 mm long dia 16mm aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section complete all as specified and as directed.

Supply and fixing second class hard wood small fittings such as brackets of any type, shaped door and windows stops and the like article not exceeding 200 Cu.cm each and fixed complete all as specified and as directed.

Supply and fixing mild steel enamelled helical door spring 150 mm (ISI marked) size including roller and roller plate, fixed to wooden / steel frames by any means as required complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.0 mm and fixed with tinned tacks or galvanised wire staple complete all as specified and as directed.

Supply and fixing 3mm thick sheet glass, ordinary quality glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

Material and labour for preparing surface of new wood and wood based material of any description and girth, not otherwise described and treated with two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

Material and labour for preparing surface of new steel material of any description and girth, not otherwise described and treated with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

Material and labour for providing and fixing in position suspended false ceiling system using 'E' grid suspended ceiling grid system. The size of grid shall be 600 X 600mm with GI frame work, main runner 39X24mm, cross tee 29X24mm and wall angle 22.2 X 22.2mm using 4mm thick high pressure stream cured non primered classic / designer variant 'E'-Board ISI Marked IS No : 14862-2000. Fibre cement 'E' Board to be placed in the gird of 'E' grid suspended ceiling grid system duly suspended by 4mm dia GI bar hangers from the purlins of the roof with butterfly clips including dismantling wall and ceiling boards (fibre pulp / insulation) any thickness including cover fillets including taking down all electric fittings fixed with ceiling and refixing the same in position after replacing the ceiling complete all as specified and as directed.

Demolition of concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Material and labour for 25 mm thick PCC (1:2:4) type B-0 (using 12.5mm graded crushed stone aggregate), as in sub base / floor complete all as specified and as directed.

Material and labour for non skid ceramic colour tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm screed bed in cement mortar (1:6) complete all as specified and as directed.

Material and labour for non skid ceramic coloured tiles 7 to 8mm thick, edgeless, area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match shade, pattern, laying etc of tiles including 15mm screed bed in cement mortar (1:6) complete all as specified and as directed.

Description all as per Ser item No 52.00 here-in-before but as in skirting over and including 10 mm thick rendering in cement mortar (1:4) complete all as specified and as directed.

Material and labour for glazed ceramic coloured tiles (450 x 350 mm) x 7 mm thick as in dados, skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick rendering in cement mortar (1:4) complete all as specified and as directed.

Material and labour for 16 to 18mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing into white cement (1:2) using marble dust with admixture of pigment to match shade of granite over and incluidng 20mm thick screed bed of cement mortar (1:6) including taking down old complete all as specified and as directed.

Dismantling stone slabs laid dry and tiles of any description or thickness in floors, aprons etc. and rubbish off the premises complete all as specified and as directed.

Material and labour for machine cut kota stone slab flooring 18-20mm thick as in floor to match the shade of the slab including 20mm screed bed in cement mortar (1:6) including rubbing, polishing complete all as specified and as directed.

Material and labour for machine cut kota stone slab flooring 18-20mm thick as in riser in step, skirting / dado to match the shade of the slab including rubbing and polishing over and including 10mm rendering in cement mortar (1:4) complete all as specified and as directed.

Taking up or down 15 mm bore steel tubing and connections including cleaning for refixing or removal to store complete all as specified and as directed.

Taking up or down 20 mm bore steel tubing and connections including cleaning for refixing or removal to store complete all as specified and as directed.

Dismantling water tanks exceeding 250 and not exceeding 500 litres complete all as specified and as directed.

Supply and fixing 500 litre capacity rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) three layers hoisted and fixed in position complete all as specified and as directed.

Supply and fixing in repair vitreous china squatting pan 'Orissa' pattern, size 580 x 440 mm white, with integral foot rest and 'P' or 'S' trap and connection to flushing pipe, anti-syphonage pipe complete including provision of cement concrete bedding complete all as specified in SSR part - I and as directed.

Supply and fixing in repair vitreous china wash basin, white, flat back, size 550 x 400 mm excluding taps, waste, chain and plug and porcelain stopper but including brackets, waste coupling cutting, waste pipe for and pinning in ends of brackets or erecting stand complete all as specified and as directed.

Supply and fixing in repair PVC valveless, symphonic action type, flushing cistern, 10 litres capacity, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and as directed.

Supply and fixing in repair low density PVC connections commercial quality 15mm bore with PTMT nuts of length 450mm complete all as specified and as directed.

Supply and fixing in repair low density PVC waste pipe 32 mm bore for flushing cistern complete all as specified and as directed.

Supply and fixing in repair 15 mm bore bib taps long nose / long body, cast copper alloy chromium plated fancy type with capstan head handle screwed down, screwed for brass, weight not less than 450 grams ferrule and fixed complete all as specified and as directed.

Supply and fixing in repair 15 mm bore angle valves, cast copper alloy chromium plated fancy type, half turn, screwed down, high pressure, with crutch or butterfly handle, weight not less than 450 grams screwed both ends for iron pipe or for unions complete all as specified and as directed.

Supply and fixing in repair 15 mm bore brass stop cock, cast copper alloy chromium plated with long shank and cup (concealed type), high pressure, with capstan head handle, weight not less than 450 grams screwed both ends for iron pipe or for unions complete all as specified and as directed.

Supply and fixing in repair 15mm dia chromium plated pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot or Cold' with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and as directed.

Supply and fixing in repairs 20 mm dia gun metal, globe or gate valve with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed.

Supply and fixing in repairs shower rose brass chromium plated with swivel joint of size 125 mm cast copper alloy chromium plated fancy type with chromium plated neck 9" long made to shape, weight not less than 350 grams complete all as specified and as directed.

Taking down eaves, gutters and rainwater pipes (any size or pattern) including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and as directed.

Supply and fixing 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, bends, Tees complete fixed to walls at any height complete all as specified and as directed.

Supply and fixing 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, bends, Tees complete laid in trenches or in floors complete all as specified and as directed.

Supply and fixing 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, bends, Tees complete fixed to walls at any height complete all as specified and as directed.

Supply and fixing 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, bends, Tees complete laid in trenches or in floors complete all as specified and as directed.

Supply and fixing in repair PVC (SWR) bends 110 mm radius complete all as specified and as directed.

Supply and fixing in repair 110 mm PVC (SWR) junction single (T) equal / unequal complete all as specified and as directed.

Supply and fixing in repair PVC (SWR) bends / shoes any radius of 75 mm dia complete all as specified and as directed.

Supply and fixing in repair PVC (SWR) bends any radius provided with access door of 110mm dia complete all as specified and as directed.

Supply and fixing in repair PVC (SWR) bends any radius provided with access door of 75mm dia complete all as specified and as directed.

Supply and fixing stack clamps made out of 50mm x 5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stay to walls or roof for 75 mm bore pipe complete all as specified and as directed.

Supply and fixing stack clamps made out of 50mm x 5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stay to walls or roof for 100mm bore pipe complete all as specified and as directed.

Supply and fixing in repair 75 mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement including jointing to waste pipe fixed in cement concrete (1:2:4) type B-1 complete all as specified and as directed.

Supply and fixing 20 mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (minimum weight - 210 grams) complete all as specified and as directed.

Supply and fixing in repair brass chromium plated towel rail 20 mm dia 'D' type 60 cm long between flanges complete all as specified and as directed.

Supply and fixing in repair mild steel peg set of six power coated as approved by GE complete all as specified and as directed.

Supply and fixing in repair drapery curtain rod of metalic 25 mm dia covered with PVC coating including mild steel bracket, end ball, rounded block (coated with brown / cherry / golden colour) of approved pattern and shade fixed in position by drilling holes in walls and fixed the brackets with rawl plug and steel screws complete all as specified and as directed.

Supply and fixing in repair glass shelf rectangular size 450mm x 150mm, 5 mm thick glass with stainless steel bracket as per sample kept in AGE B/R office complete all as specified and as directed.

Supply and fixing in repair cabinet mirror of PVC moulded size 600 x 450 mm as per sample kept in AGE B/R office complete all as specified and as directed.

Supply and fixing in repair sinks with drainage board made of stainless steel 1 mm thick in kitchen with plugs, washers and waste coupling, waste pipe including bedding in cement mortar on wall including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460 mm, bowl size 410mm x 330mm x 160 mm complete all as specified and as directed.

Demolition of cinder concrete of any description and in any position and removing the rubbish from work site complete all as specified and as directed.

Taking down existing sunken treatment and cleaning sunken surface by washing and rubbing etc. and removing the material retrieved to a distance not exceeding 500 m where directed. Material and labour for providing water proofing treatment to sunken floors all as given below: - (a) Making fillet of size 25mm x 25mm at corner of slab and wall with polymer modified cementitious (PMC) mortar consisting of one part of tapecrete P-151, two parts of cement and 6 parts of fine sand by weight. (b) Sealing of joints of pipe with epoxy putty CICO POXY LC or epoxy mortar CICO POXY 2125. (c) Cleaning the concrete surface by brushing and watering and applying a coat of tapecrete P-151 Acrylic Polymer Modified cementitious slurry consisting of one part of TAPECRETE P-151 and two parts of cement by weight. The coating shall be carried out upto 300mm above FFL and shall be allowed to dry for 4-6 hours. (d) Appying a coat of TAPECRETE brush topping 1.5mm thick consisting of one part of TAPECRETE P-151, two parts of cement and two parts of silica sand by weight and cured to 2 days. (e) Applying 15mm thick plaster in cement mortar (1:4) mixed with CICO super @ 100ml per 50 Kg cement on treated surface. (f) Material and labour for cement concrete (1:5:10) type E-2 as in filling of sunken floor. Note: - Ponding test should be performed for 48 hours as per directions of Engineer-in-Charge.

Material and labour for galvanised iron spout 25mm dia light grade, fixed to walls complete all as specified and as directed by Engineer-in-Charge.

Material and labour for plastering 10mm thick in cement mortar (1:3) using 100% coarse sand on roof surface including water proofing compound as per manufacturer's instructions complete all as specified and as directed by Engineer-in-Charge.

Supply and applying two coats of undiluted thick coats of acrylic reinforcement liquid applied elastometric water proofing membrane with ultravoilet resistant properties and solar reflective properties over one coat of primer (3:1 water dilution) before applying second coat insert smart care roof tape corner/joints and allow it to dry then apply further coat complete all as specified and as directed. Note: - Every coat time gap should be minimum 6 hours.

Supply only liquid water proofing compound complete all as specified and as directed.

Supply and fixing floor door stopper of aluminium alloy body and tongue 140 mm anodised with hard drawn steel spring fixed in floor complete all as specified and as directed.

Dismantling timber scantling 40 Sqcm and over in section in any position as in unframed work complete all as specified and as directed.

Dismantling timber scantling in fillets, posts, rafters, purlins etc under 40 Sqcm in section complete all as specified and as directed.

Dismantling AC corrugated, semi corrugated sheets in roof covering including ridge complete all as specified and as directed.

Supply and fixing pre-painted galvalume aluminium zinc coating galvanised iron based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 MPs as in roof covering fixed with self tapping screws or L-type or J-type or cranked hook bolts complete all as specified and as directed.

Supply and fixing pre-painted galvalume aluminium zinc coating galvanised iron based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 MPs as in ridge of roof fixed with self tapping screws or L-type or J-type or cranked hook bolts complete all as specified and as directed.

Supply and fixing structural steel / tubular section work as in roof trusses (framed), post, trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections or mild steel tube pipe) including distance pieces, cleats etc Fe-410W (Grade 'E'-250) quality 'A' including shop coat of primer complete all as specified and as directed.

Demolition of brick work or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars, drains etc but excluding ashlars facings, dressed stone work and precast concrete articles complete all as specified and as directed.

Material and labour for brick work with sub class ‘B’ bricks straight or curved on plan exceeding 6m mean radius built in cement mortar (1:6) complete all as specified and as directed.

Material and labour for brick work with sub class 'B' bricks straight or curved on plan to any radius in half brick thick wall in cement mortar (1:4) complete all as specified and as directed by Engineer-in-Charge.

Excavation in trenches not exceeding 1.5m wide, not exceeding 1.5m in depth for foundation, etc, or for shafts, wells cesspits, manholes, pier holes, for laying of drain pipes etc not exceeding 10 Sqm on plan and not exceeding 1.5m in depth and getting out in hard / dense soil complete all as specified and as directed.

Demolition / breaking of drain pipes (salt glazed ware, AC or reinforced concrete) set in cement mortar and taking out off trenches and removing the debris from the site of 150mm / 200 mm dia pipe including demolition of cement concrete, haunching etc complete all as specified and as directed.

Material and labour for concrete bed to 150 mm bore pipe (1:4:8) in type D-2 (using 40mm graded crushed stone aggregate) including haunching against the sides of pipe complete all as specified and as directed.

Supply and fixing and laying 150 mm thick reinforced concrete pipes class NP-2 laid and jointed complete with collars as in trenches complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm complete all as specified and as directed.

Removal of surplus excavated soil to a distance exceeding 250 m and not exceeding 500m and deposited where directed at a level not exceeding 1.5 m above the starting point complete all as specified and as directed.

Material and labour for providing precast cement concrete in cover slab (for manhole) (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) set in cement mortar (1:4) complete all as specified and as directed.

Material and labour for mild steel TMT bars 10 mm dia and over cut to length, bend to shape etc complete binding with and including mild steel annealed wire not less than 0.09 mm dia conforming TMT bars complete all as specified and as directed.

Description all as per Ser item No 117.00 here-in-before but 5 mm dia and over and including 10mm dia in stirrups, spacers and binders etc complete all as specified and as directed.

Material and labour for cement concrete (1:3:6) type C-2 (using 40mm graded crushed stone aggregate) in foundation, filling and mass concrete complete all as specified and as directed.

Taking out of solid / semi solid sludge from existing main holes of any size and any depth and burying the entire sludge / sludge water into excavated pit of adequate size including excavation and covering with earth or disposing off into covered vehicles outside the peripherry of defence land to a distance exceeding 1 KM including taking off RCC / iron main holes covers and refixing the same after clearing complete all as specified and as directed.

Material and labour for cement concrete type (1:3:6) type C-2 (using 40 mm graded crushed stone aggregate) as in surface channels complete all as specified and as directed.

Material and labour for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement complete all as specified and as directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Material and labour for reinforced cement concrete (nominal mix) (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

Material and labour for formwork to flat soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) rough finished complete all as specified and as directed.

Material and labour for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exceeding 20 cm wide and sides of RCC / PCC bands in walls, horizontal or sloping and similar work exceeding 10 cm but not exceeding 20cm wide complete all as specified and as directed.

Supply and fixing in repair PVC (SWR) vent cowl of radius of 75 mm dia complete all as specified and as directed.

Supply and fixing in repair soap dish steel chromium plated 100 mm size complete all as specified and as directed.

Supply and fixing in repair plate rack stainless steel of size 600 x 900 mm fixed with washer and plugs complete all as specified and as directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in any type of soil complete all as specified and as directed.

Material and labour for PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) as in mass concrete, in foundation complete all as specified and as directed.

Material and labour for RCC (1:2:4) type B-0 (using 12.5 mm graded crushed stone aggregate) as in cement concrete, in PCC band and lintel band, in lintels upto 1.5m clear span and other similar bands, plinth courses complete all as specified and as directed.

Material and labour for cutting chases, pinning in, making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc. and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting not exceeding 10 cm girth complete all as specified and as directed.

Material and labour for brick work with fly ash bricks (old size brick), straight or curved on plan exceeding 6 m mean radius built in cement mortar (1:6) complete all as specified and as directed.

Material and labour for brick work with fly ash bricks, straight or curved on plan to any radius in half brick wall built in cement mortar (1:4) complete all as specified and as directed.

Material and labour for hardcore of gauge not exceeding 63 mm of broken stone or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

Material and labour for 75 mm thick PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) in floor, as sub base complete all as specified and as directed.

Material and labour for provision of roof treatment with polymeric water proofing membrane all as given below: - (a) Material and labour for plastering 10 mm thick in cement mortar (1:3) using 100% coarse sand on roof surface including water proofing compound as per manufacturer's instructions and as directed by Engineer-in-Charge. (b) Applying a coat of bituminuous primer conforming to IS : 3384-1986 @ 0.25 Iitres / Sqm on prepared surface and allowed to dry. (c) Applying and laying 3mm thick APP membrane having non woven polyester matt at core and covered with high quality polymeric asphaltic protected thermo fusible HMHDPE film on both sides with over laps 10 cm and 15 cm at longitudinal and transverse direction respectively and sealed by flame, sealing all overlaps complete including treatment at all junctions and corners. The membrane shall be torched into groove on vertical plane and groove sealed with cement mortar (1:3). (d) Material and labour for two coats of aluminium paint on membrane surface 1338.40 complete all as specified and directed.

Supply and fixing 15 mm dia galvanized pipes medium grade with all fittings and fixed complete wall and ceiling or laid in floors complete all as specified and as directed.

Supply and fixing 20 mm dia galvanized pipes medium grade with all fittings and fixed complete wall and ceiling or laid in floors complete all as specified and as directed.

Supply and fixing 25 mm dia galvanized pipes medium grade with all fittings and fixed complete wall and ceiling or laid in floors complete all as specified and as directed.

Supply and fixing rotational moulded polyethylene water tank (cylindrical vertical closed top) hoisted and fixed in position capacity of tank 1000 litres and supply and fixing ball brass valve high pressure with polythene float and fly nut complete 20mm bore screwed to pipe for brass complete all as specified and as directed.

Material and labour for preparing plastered surface and applying three coats of white wash on wall complete all as specified and as directed.

Material and labour for preparing plastered surface and applying two coats of cement based paint on wall over a coat of primer complete all as specified and as directed.

Material and labour for providing edge moulding to 18-20mm thick granite stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete all as specified and as directed.

Supply and fixing vitreous china squatting pan 'Orissa' pattern, size 580 x 440 mm white, with integral foot rest and 'P' or 'S' trap and connection to flushing pipe, anti-syphonage pipe complete including provision of cement concrete bedding complete all specified in SSR part - I complete all as specified and as directed.

Supply and fixing vitreous china white under counter wash basins (595 x 420 x 200 mm) oval shape, including waste pipe, brackets and connecting pipe fixed complete all as specified and as directed.

Supply and fixing PVC valveless, symphonic action type, flushing cistern, 10 litres capacity, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and as directed.

Supply and fixing low density PVC connections commercial quality 15mm bore with PTMT nuts of length 450mm complete all as specified and as directed.

Supply and fixing low density PVC waste pipe 32 mm bore for flushing cistern complete all as specified and as directed.

Supply and fixing 15 mm bore bib taps long nose / long body, cast copper alloy chromium plated fancy type with capstan head handle screwed down, screwed for brass, weight not less than 450 grams ferrule and fixed complete all as specified and as directed.

Supply and fixing 15 mm bore angle valves, cast copper alloy chromium plated fancy type, half turn, screwed down, high pressure, with crutch or butterfly handle, weight not less than 450 grams screwed both ends for iron pipe or for unions complete all as specified and as directed.

Supply and fixing 15 mm bore sawn neck pillar cock cast copper alloy, chromium plated with angular knob fixed to 15mm dia mild steel pipe complete all as specified and as directed.

Supply and fixing 20 mm dia gun metal, globe or gate valve with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed.

Supply and fixing 75 mm PVC (SWR) junction single (T) equal / unequal complete all as specified and as directed.

Supply and fixing PVC (SWR) vent cowl of radius of 75 mm dia complete all as specified and as directed.

Supply and laying vitreous china urinals, flat back size of 465 x 355 x 265 mm white with grating and union for discharge pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar (1:2), securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe, brackets and chromium plated waste coupling including urinal spreader complete all as specified and as directed.

Supply and fixing 125 mm chromium plated stainless steel grating with or without waste hole complete all as specified and as directed.

Material and labour for PCC (1:3:6) type C-2 (using 40 mm graded crushed stone aggregate) in foundation of manholes complete all as specified and as directed.

Material and labour for RCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) in precast manhole cover and cover slab for septic tanks and including necessary formwork and moulds etc and set in cement mortar (1:4) complete all as specified and as directed.

Material and labour for cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (½ round or 3/4 section) in cement concrete (1:2:4) type B-1 smooth finished and reforming benching as required of 150mm dia pipe complete all as specified and as directed.

Material and labour for RCC (1:2:4) nominal mix type B-1 (using 20mm graded crushed stone aggregate) as in foundations including rafts, footings, foundation beams, plinth beams, bases for columns etc.; basement slabs, under reamed piles and mass concrete etc complete all as specified and as directed.

Material and labour for RCC (1:2:4) nominal mix type B-1 (using 20mm graded crushed stone aggregate) as in columns, pillars, piers, posts and struts etc complete all as specified and as directed.

Material and labour for RCC (1:2:4) nominal mix type B-1 (using 20mm graded crushed stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span etc complete all as specified and as directed.

Material and labour for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work; vertical or to batter etc complete all as specified and as directed.

Material and labour for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and as directed.

Material and labour for formwork to sides of pillars, posts, struts, piers, columns and stanchions etc complete all as specified and as directed.

Material and labour for rendering 15mm thick on brick work or concrete surfaces on other than fair faces of brick work built in cement mortar (1:6) and finished even and smooth without using extra cement complete all as specified and as directed.

Supply and fixing shower rose brass chromium plated with swivel joint of size 125 mm cast copper alloy chromium plated fancy type with chromium plated neck 9" long made to shape, weight not less than 350 grams complete all as specified and as directed.

Supply and fixing brass chromium plated towel rail 20 mm dia 'D' type 60 cm long between flanges complete all as specified and as directed.

Supply and fixing mild steel peg set of six power coated as approved by GE complete all as specified and as directed.

Supply and fixing soap dish steel chromium plated 100 mm size complete all as specified and as directed.

Material and labour for construction of septic tank for 25 users capacity including excavation and earth work in ordinary soil, foundation with PCC (1:2:4) type B-1, brickwork in cement mortar (1:4), RCC (1:2:4) type B-1 slab, RCC precast manhole cover having 6mm plate embedded around with angle iron frame, vent shaft and sludge chambers etc all as shown on drawing no. CEPZ/C-TD-013-13 complete all as specified and as directed. Note: - Rate quoted includes final depth of Invert level of septic tank on the basis of longitudinal slope of sewage line.

Material and labour for construction of soakage well 1.80 M dia and 3.0 M (Effective depth) deep excavation in any type of soil foundation in PCC (1:3:6) walls of honey combed brick work with top ring of M-25 concrete including intercepting chamber and screen chamber made of brick work in cement mortar RCC cover slab M-25/SFRC cover interconnecting pipes of RCC /DEC complete filled with brick bats as shown on drawing no. CEPZ/C-TD-013-13 complete all as specified and as directed.

Material and labour for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design and pattern as in footpath, parks, lawns, drive ways or light traffic parking etc. of required strength, thickness and size / shape made by table vibratory method using PU mould, laid in required colour and pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding / laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed.

Material and labour for providing cement concrete (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and as directed.

E/M Portion: - Taking down old unserviceable copper / aluminium point wiring concealed / batten (light, fan, socket or power) complete including fixture and fittings such as switches, sockets, ceiling roses, bell push, bell electric, lamp holder, bulk head fitting, pendants, regulators, sockets, light fitting and any type of switch board wooden / iron, round block etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors etc complete all as specified and as directed.

Material and labour for sub main wiring with proper colour coding, insulated, unsheathed, multistranded, copper conductor FRLS, cable of 2 run 6 Sqmm for phase and neutral and one run of 6.0 Sqmm for earth wire unsheathed, multistranded, copper conductor FRLS, drawn through the existing rigid PVC concealed conduit fixed on wall. Two runs of cable for phase / neutral and one run of cable for earth will be measured and paid as one unit length including taking down of old wiring complete all as specified and as directed. Note: - Wiring shall be done in proper colour coding.

Material and labour in replacement for wiring for circuit with proper existing colour coding, insulated, unsheathed, multistranded, copper conductor FRLS, cable of 1 run 1.5 Sqmm for phase, drawn through the existing rigid PVC concealed conduit fixed on wall for inverter connection of light and fan point complete all as specified and as directed.

Material and labour for complete point wiring with 1.5 Sqmm single core multistranded copper conductor FRLS insulated and unsheathed heavy duty cable in colour code including continuous earth wire with cable of size 1.5 Sqmm copper conductor flexible FRLS insulated drawn in and including concealed PVC rigid conduit medium grade ISI marked after cutting chases in wall, plastering after concealing conduit including modular galvanised flush boxes of suitable size and white cover plate with frame as per relevant IS for mounting modular switches, sockets, fan regulators etc and including making good the disturbed surface as per existing complete all as specified and as directed by Engineer-in-Charge for the following: -

Description all as per Ser item No 181.00 here-in-before but for multi 5 pin 5 amp socket outlet on same board complete all as specified and as directed.

Description all as per Ser item No 181.00 here-in-before but for multi 3 pin socket outlet 5 amp socket on independent board complete all as specified and as directed.

Description all as per Ser item No 181.00 here-in-before but for one light point controlled by two 2 way switches, with cable 1.5 Sqmm complete all as specified and as directed.

Description all as per Ser item No 181.00 here-in-before but for one bell / buzzer point controlled by one push button on the same board with other switches or independent with cable 1.5 Sqmm size complete all as specified and as directed.

Description all as per Ser item No 181.00 here-in-before but for multi 3 pin 15 Amp socket outlet independent controlled by 15 Amp switch with 2.5 Sqmm copper conductor multistranded cable PVC insulated FRLS and unsheathed cable in and including PVC rigid concealed conduit 20/25 mm dia and unsheathed copper conductor multistranded cable 2.5 Sqmm as earth wire FRLS PVC insulated in green color complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair modular switch 1 way 6 A, 1 module, 240 volts ISI marked complete all as specified and as directed.

Supply and fixing in repair modular socket, 6A - 5 pin combined 2 module, 240 volts ISI marked complete all as specified and as directed.

Supply and fixing in repair modular switch 2 way 6A, 1 module, 240 volts ISI marked complete all as specified and as directed.

Supply and fixing in repair modular bell push 6A, 1 module, 240 volts ISI marked complete all as specified and as directed.

Supply and fixing in repair modular switch 1 way 16A, 1 module, 240 volts ISI marked complete all as specified and as directed.

Supply and fixing in repair modular socket 6A/16A - 6 pin combined 2 module, 240 volts ISI marked complete all as specified and as directed.

Supply and fixing in repair ceiling rose, 3 Phase / PVC / polycarbonate isolated body complete all as specified and as directed.

Supply and fixing in repair calling bell Ding Dong AC 230 Volts, single pole complete all as specified and as directed.

Material and labour in replacement for fan regulator stepped electronic type suitable for AC, 240 V complete all as specified and as directed.

Material and labour in replacement for lamp holder, PVC / polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed.

Material and labour in replacement self ballast LED retrofit lamp with PVC body and PC Diffuser 9 watt 230 Volt 6500K complete all as specified and as directed.

Supply and fixing in replacement LED light fitting 1 x 20W, 220 V, AC decorative box type complete with LED tube rod 20 watts driver, holder and power factor >0.95, 100 Lumen/Watt, 6500 K cool day type conforming to ISI including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete (4' ft long) complete all as specified and as directed.

Supply and fixing in replacement LED light fitting 1 x 9 W / 1 X 10W bulk head luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and fixing in replacement LED light fitting mirror type with high output diffuser 2 feet, 12 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Taking down existing unserviceable ceiling fan repair / maintenance including replacement of unserviceable spare parts i.e. bearing, bush, PVC connector, PVC clamp, canopy, capacitor including painting, rewinding of any make / type and size (1200 / 1400 mm sweep) with super enamelled copper wire of appropriate gauge as existing to obtain the specified and satisfactory RPM as per manufacturer's specification including replacement of all insulation materials, varnishing, heating, drying, assembling of stator / rotor, connection and testing complete all as specified and as directed.

Supply and fixing in replacement of vertical distribution board (TP&N) 4 way double door suitable for and including MCCB 125 Amp 16 KA four pole as incomer and outgoing MCB's and should be IP-43 protected with copper bus bars, neutral links, earthing bar including taking down old unserviceable distribution board / MCB any type complete all as specified and as directed. Notes: - (i) MCB's shall be measured and paid separately. (ii) TPN distribution board and MCCB should be of same make.

Supply and fixing in replacement 415 V 10 KA 'B' curve MCCB TPN 125 Amp capacity in the distribution board complete with connection, testing and commissioning complete all as specified and as directed.

Material and labour for replacement of distribution board sheet steel powder coated for MCB with copper bus bar and neutral link earthing stud SPN 8 way 240 volts double door complete all as specified and as directed by Engineer-in-Charge. Note: - Distribution board and MCB's should be of same make.

Supply and fixing in replacement of SPN 40 to 63 Amp rating 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB distribution board complete with connection, testing and commissioning complete all as specified and as directed.

Supply and fixing in replacement 240 V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 Amp, in the MCB distribution board complete with connection, testing and commissioning complete all as specified and as directed.

Taking down existing serviceable / unserviceable electric meter alongwith existing angle iron steel box from the wall and refixing electric meter in position after repair / replacement of MCB TPN box including replacement of PVC flexible conduit for cable protection complete with making the existing wall neat and clean including patch work, plaster, brick work and white wash as per site requirement complete all as specified and as directed.

Material and labour in replacement for earthing complete with galvanised mild steel earth plate electrode of size 600 x 600 x 6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 metre deep below normal ground level with top edge of the earth plate not less than 1.5 metre below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised iron including PCC pit in PCC (1:2:4) type B-1 precast RCC cover slab using reinforcement with suitable handle made of round bar including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion complete all as specified and as directed.

Material and labour for point wiring for one light / fan / call bell point controlled by one 5 Amp switch with 1.5 Sqmm single core multistranded copper conductor FRLS, PVC insulated (unsheathed) heavy duty cable including continuous earth wire of size 1.5 Sqmm copper conductor multistranded FRLS, PVC insulated (unsheathed) drawn into and including new concealed PVC rigid / 1.8 mm wall thickness ISI marked including new cast iron / pressed steel terminal boxes including 3.00mm thick hylam brand IS-2036 marked, laminated sheet cover for mounting switches, sockets, fan regulators etc complete all as specified and as directed. Notes: - (a) Wiring shall be done by using proper colour coding. (b) Earth wire shall be of green colour. (c) On RCC roof / ceiling PVC conduit shall be provided on surface with proper fixing clamps all as directed by Engineer-in-Charge.

Description all as per Ser item No 209.00 here-in-before but for multi 5 pin 5 amp socket outlet on same board complete all as specified and as directed.

Description all as per Ser item No 209.00 here-in-before but for multi 3 pin 15 Amp socket outlet independent controlled by 15 Amp switch with 2.5 Sqmm copper conductor multistranded cable PVC insulated FRLS and unsheathed cable in and including PVC rigid concealed conduit 20/25 mm dia and unsheathed copper conductor multistranded cable 2.5 Sqmm as earth wire FRLS PVC insulated in green color complete with new cast iron / pressed steel sunken black with hylum top sheet cover complete all as specified and as directed.

Supply and fixing socket outlet 5 Pin, 5 A, flush type complete all as specified and as directed.

Supply and fixing switch piano, flush type single pole one way 5 Amp, 240 volts complete all as specified and as directed.

Supply and fixing ceiling rose, 3 Phase / PVC / polycarbonate isolated body complete all as specified and as directed.

Material and labour switch piano flush button single pole one way 15 Amp complete all as specified and as directed.

Material and labour socket outlet 3, 5 pin and 15 Amp multipurpose shuttered type complete all as specified and as directed.

Material and labour for lamp holder, PVC / Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed.

Material and labour for self ballast LED retrofit lamp with PVC body and PC Diffuser 9 watt 230 Volt 6500K complete all as specified and as directed.

Supply and fixing LED light fitting 1 x 20W, 220V, AC decorative box type complete with LED tube rod 20 watts driver, holder and power factor >0.95, 100 Lumen/Watt, 6500 K cool day type conforming to ISI including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete (4' ft long) with LED rod 20 watt, 230 Volts 50 Hz complete all as specified and as directed.

Supply and fixing LED light fitting 1 x 9W / 1 X 10W bulk head luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and fixing exhaust fan made of sturdy engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, copper winding of sweep 300m complete all as specified and as directed.

Material and labour for distribution board sheet steel powder coated for MCB with copper bus bar and neutral link earthing stud SPN 2 way 240 volts double door complete all as specified and as directed by Engineer-in-Charge. Note: - Distribution board and MCB's should be of same make.

Supply and fixing 240 V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 AMP, in the MCB distribution board complete with connection, testing and commissioning complete all as specified and as directed.

Supply and laying and testing cable XLPE insulated screened PVC bedded galvanised steel strip or wire armoured, electric power cable (Heavy duty) with stranded aluminium conductor 1100 V grade cross sectional area 10 Sqmm, 2 core in and including taking out old one complete all as specified and as directed.

M/S Sukhmani Construction Co. (BID ID -3100046)

M/s KULDEEP KUMAR CONTRACTOR (BID ID -3100385)