SPECIAL REPAIR TO BUILDING NO P 03 F1 PROVN OF 02 GUARD POSTS AT FLAG STAFF HOUSE AND PROVN OF ONE TOILET WITH BATHROOM NEAR BLDG NO P2 F OF HQ AFSOD UNDER GE W AGRA

Amount

Surface execavation n. exc 30 cm deep & averaging 15 cm deep & getting out in soft loose soil including cutting to required gradient and camber as for formation of roads/berms complete all as specified & as directed.

Excavating in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc or not exceeding 10 Sqm on plan for shafts, cesspits, manholes, pier holes, etc and getting out in loose/soft soil complete all as specified & as directed.

Excavating in post holes (or similar holes) each not exc. 0.5 cum, getting out in soft/loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified & as directed.

Removal of surplus excavated soil to a distance not exc 50m and depositing where directed at a level not exc. 1.5m above the starting point complete all as specified

Returning, filling in including spreading, leveling, watering and well ramming in layers not exc 25 CM as in soft/lose soil complete all as specified & as directed.

Spreding and levelling in layers not exc 25 cm thick well ramming including watering as required with excavated soil complete all as specified & as directed.

M & L for cement concrete 1:4:8, type D2 (Using 40mm graded stone aggregate) as in foundation & mass concrete complete all as specified & as directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc complete all as specified & as directed.

M & L for brick work with sub class ‘B’ brick old size bricks straight or curved on plan exc 6 Mtr mean radius built in CM (1:6) complete all as specified & as directed.

M & L for brick work with sub class ‘B’ brick old size bricks (Except bricks) straight or curved on plan exc 6 Mtr mean radius built in CM (1:6) complete all as specified & as directed.

S & F Rolled mild steel sections conforming to Gde Fe-410-0 or Fe-310-0 as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails & guides for sliding doors, fixed with angle cleats or other connecting plates complete.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an color having tensile strength of 550 MPa as in roof covering including ridge /cladding to wall, fixed with self tapping screws complete all as specified & as directed.

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified & as directed.

S&F for Factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified & as directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top &bottom rails. MS framed shall be covered with heat molded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail &bottom rail on either side & as gap insert for top rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS framed welded/sealed to stiles & rails with suitable PVC sheet beading & joined together with solvent cement complete all as specified & as directed.

S&F 100 mm size butt hinges extruded aluminium alloy with galvanized mild steel hinge pin anodized and fixed type B-22 complete all as specified & as directed.

S&F 150 mm size aluminum anodized barrel tower bolt of extruded section complete all as specified & as directed.

S&F alluminium anodized barrel tower bolt of extruded section, 200 mm long complete all as specified & as directed.

S&F 125 mm size aluminum cost type anodized handle complete all as specified & as directed.

S&F extruded aluminium anodized handle cast type 150 mm long complete all as specified & as directed.

S & F steel ventilator with top hung shutter including hinges of steel, peg stay etc. complete all as specified & as directed.

S & F frame work such as grills, guard bars and similar work confirming to Fe-410-0 or Fe 310-0 complete all as specified & as directed.

S&F galvanized M.S. wire cloth, 0.45 mm nominal dia of wire and average width of aperture 1.18 mm with tinned tacks complete all as specified & directed.

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.50 Sqm in each pane complete all as specified & directed.

S&F 3 mm thick figured glass, frosted head type and glazing with oil putty in square n.exc 0.5 sqm in each pane complete all as specified & as directed.

M&L Plain Cement concrete 1:2:4, type B-0 (using 12.5 mm greded stone aggregate) in leveling course, benching etc, finished even & rough to receive cement mortar screed bed complete all as specified & as directed.

M & L for coloured glazed ceremic tiles 300 x 200 x 5 to 6mm thick on vertical surfaces etc set and jointed in neat cement slurry and pointed in coloured cement to match tiles & screed bed 10 mm thick in C M 1:4 complete all as specified & as directed.

S&F PVC low level flushing cistern 10 Ltr capacity, white with all fittings and fixtures including brackets and 32 mm bore PVC flush pipe complete all as specified & as directed.

S&F PVC connections 15 mm Size & 450 mm long with brass check nuts on both ends complete all as specified & as directed.

S&F bib tap cost copper alloy chromium plated fancy type with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule in 15 mm bore complete all as specified & as directed.

S&F brass chromium plated two way brass angle stop cock 15 mm bore pipe complete all as specified & as directed.

S&F tubes medium grade galvanised pipe with all fittings laid in trenches in 15 mm bore complete all as specified & as directed.

S&F tubes medium grade galvanised pipe with all fittings laid in trenches in 20mm bore complete all as specified & as directed.

S&F rotational moulded polyethylene wator storage tanks (cylindrical vertical with closed top) tripple layer hoisted and fixed in position as specified in SSR Pt I 500 litre capacity complete all as specified & as directed.

S&F ball valve PTMT high pressure with polyethylene float and nut complete screwed for iron pipe or brass ferrule of 20mm bore complete all as specified & as directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any lenth with rubber ring joints, fixed to wall or floor complete all as specified & as directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any lenth with rubber ring joints, fixed to wall or floor complete all as specified & as directed.

S&F PVC (SWR) bends any radius 75mm dia complete all as specified & as directed.

S&F PVC (SWR) bends any radius 110mm dia complete all as specified & as directed.

S & F PVC (SWR) floor trap , plain with grating including jointing with solvent, dia of out let 75mm complete all as specified & as directed.

S&F Vitreous china urinal bowl type flat back size of 465X355X265 mm white (Minimum) with grating and union for discharge pipe (excluding flushing cistern, flush pipe) complete provide and fixing plugs, bedding urinal against wall in CM 1:2, securing urinal to plugs with and including 60mm long brass screws pointing around urinal back in cement with brackets, flush pipe, grating and union for discharge pipe (exclusive of fixing supply pipe flushing cistern trap and waste pipe) complete all as specified & as directed.

S&F vitrous china squating pan orissa pattern size 580 x 440 mm white with integrat foot rest fixed in repairs including provision of lime concrete bedding complete all as specified & as directed..

S&F vitreous china white wash hand basin flat back size 550x400mm excluding taps, waste, chain, and plug and porcelain stopper but including bracket & cutting for and pinning in end of brackets or erecting stand complete all as specified & as directed.

S&F pillar tap cast copper alloy with capstan head chromium plated screwed down with or without littered Hot & cold with long screwed shank and ply nut screwed for iron pipe of 15 mm bore dia complete all as specified & as directed.

S&F shelf of PTMT fixed and including chromium plated brass screws & wooden/plastic cleats (Minimum weight 300 gms) complete all as specified & as directed.

S&F chomium plated shower roses 125 mm size with or without swivel joints any size including fixing to steel pipe or unoin complete all as specified & as directed.

S&F Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed for 15 mm bore dia of pipe complete all as specified & as directed.

S&F Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed for 20 mm bore dia of pipe complete all as specified & as directed.

S&F tubular towel rail of brass chromium 20 mm dia D type , 60 cm long between flanges complete all as specified & as directed.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc.complete all as specified & as directed.

M&L rendering 10mm thick in CM 1:6 on fair face on concrete surfaces finished even and smooth without using extra cement on wall complete all as specified & as directed.

M&L rendering 15mm thick in cement mortar 1: 4 on other than fair faces of brick work or concrete surfaces, finished fair and even including using water proofing compound as per manufacturer's instructions complete all as specified & as directed. Note: WPC will be measured & paid separately under respective item.

M&L rendering 10 mm thick in CM 1:3 on fair facces of brick work or concrete surfaces finished the surface fair and even on ceiling complete all as specified & as directed.

M&L preparation of newly plastered surfaces of wall and applying three coat of white wash complete all as specified and directed.

M&L hard core of broken bricks of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface complete all as specified & as directed.

M&L cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate) in plinth protection 50mm thick finished even and smooth without using extra cement including making joint 12 wide to the full depth of PCC at max 3 mtrs and at every change of direction and filling the same with & including bitumen and sand 1:3 by weight complete all as specified & as directed.

M&L PCC (1:3:6), type C-2 (using 40mm graded crushed stone aggregate) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150mm bore SGSW pipe complete all as specified & as directed.

M&L salt-glazed stoneware (SGSW) grade 'A' pipes 150mm internal dia laid in trenches on concrete bed and jointed complete all as specified & as directed.

M&L precast reinforced cement concrete (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in manholes cover slab etc placed in position set in CM 1:6 complete all as specified and shown on drawings

M&L 40 mm thick damp proof course in cement concrete 1:2:4, type B-0 with Liquid water proofing compound to horizontal or vertical surfaces including necessary use & waste of formworkcomplete all as specified & as directed. Note:- Integral water proofing compound will be measured and paid seperately.

Supply only liquid waterproofing compound complete all as specified & as directed.

M&L precast cement concrete 1:2:4, type B-1 (using 20mm graded stone aggregate) in window or door cills, lintels, and setting in cement mortar 1:6 complete with joints to match complete all as specified & as directed.

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including crancking, bending spirally hooping ends binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & as directed.

M&L for TMT bars 5mm dia and over up to 10 mm dia, cut to length, bent to shape required, including crancking, bending spirally hooping ends binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips as in stirrups complete all as specified & as directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of cement base paint over a coat of primer complete all as specified & as directed.

Taking down chowkats or frames (w/o taking off shutters) from the frames n.exc 1.5 Sqm each complete all as specified & as directed.

Taking down chowkats or frames (w/o taking off shutters) from the frames exc 1.5 Sqm but not exc, 4 Sqm each complete all as specified & as directed.

S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified & as directed.

S&F pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, size of frame 125 x 60mm complete all as specified & as directed.

M&L for PCC 1:3:6, type C-1 (using 20mm graded stone aggregate) as in back filling of pressed steel door frames complete all as specified & as directed.

M&L 35 mm thick 2nd class HW plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified & as directed.

S&F 30mm thick second class hard wood glazed and skelton shutters open rebated and prepared to receive glass, gauge etc (without sash bars) edges of the framing plain, chamfered rounded, fitted with cut & mitred beads for securing glass etc, sizes of members of shutters as specified in SSR Part-I, section 8 clause 8.20 (a) supplied and fitted to chowkats complete all as specified & as directed.

S&Faluminium alloy anodised sliding door bolts with hasp and staple (bolt type) and fixing clips of sheets cast or extruded sections and fixing bolts and sliding bolts or extruded section of cast alum alloy and fixed length of bolt 250mm complete all as specified & as directed.

S & F 300 mm MS ordinary rat tail spring including roller and roller plate complete complete all as specified & as directed.

S&F in repair 25mm dia decorative powder coated drapery rod, colour as approved with seasoned teak wood rings and brackets, fix to wall complete all as specified & as directed.

Providing water proofing treatment over RCC roof including projection as follows :- (a) Complete removal of existing roof treatment of any description and in any position (b) The slab shall be finished with 10mm thick cement plaster in cement mortar 1:4 finished even and smoooth (without using extra cement) mixed with water proofing compound as per manufacturer's instructions. The cement plaster shall be provided while the concrete of the slab in green (c) Apply a coat of bitumious primer conforming to IS-3384 @ 0.3 liter/Sqm on the prepared surface of plaster. After drying of primer, apply a coat of hot blown VG 20 paving grade (60-80 penetration) bitumen conforming to IS-702 @ 1.2 Kg/Sqm of plastered surface. (d) Provide polymeric water proofing membrane ISI marked laid with overlaps, bonded with hot blown bitumen, end overlaps shall not be less than 150mm as side lap 75. Polymeric water proofing membrane should be five layered with centre core as 90 microns high molecular high density polythylene film Minimum weight of water proofing membrane shall be 3Kg per Sqm. The contractor shall produce purchase vouchers and test certficate from the manufcture for the same. (e) Over the poly meric water proofing membrane apply semi hot blown VG 20 paving grade (60-80 penetration) bitumen conforming to IS-702 @ 1.2 Kg/Sqm of roof surface and blinded with fine sand in dry condition @ 0.5 Kg/Sqm dusted over the bitumen coat (f) Covered fillet in PCC (1:2:4) type B-0 (using 12.5mm graded stone aggregate) radius 75mm be provided at the junction of roof and vertical surface such as paraper wall/mumty/chimney around opening and treatment mentioned above except fine sand) shall be applied followed by a cement plaster 20mm thick in ceement mortar (1:6). Complete treatment shall be carried out by the applicator of the manufacturer of membrane. (g) Laying 40mm thick brick tiles over bedding layer 20mm screed in CM 1:4. The cement mortar screed shall be mixed with polymer based liquid water proofing additive as per manufacturer’s instructions and tile joints shall be filled with 1:3 CM mixed with crude oil as per SSR 2009(Part I).

M&L preparation of newly plastered surfaces of wall and applying two coats of oil emulsion distemper over a coat of chalk whiting complete complete all as specified & as directed.

M&L for preparation by complete removal of existing treatment of wall surfaces and applying two coats of oil emulsion distemper over a coat of wall care putty of 1mm thick complete all as specified & as directed.

M&L preparation of newly platered surfaces of wall and applying two coats of weather proof exterior emulsion (APEX) over a coat of primer complete all as specified & as directed.

M&L preparation of old decorated wal surfaes by complete removal of existing treatment and applying two coats of weather proof exterior emulsion (APEX) over a coat of primer complete all as specified & as directed.

M&L for preparation of new or previously untreated wooden surfaces over 10cm in width or grith and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified & as directed.

M&L for preparation of new or previously untreated steel surfaces over 10cm in width or grith and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & as directed.

M&L for preparation of old decorated surfaces of wooden and applying one coat of synthetic enamel paint complete all as specified & as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/metal frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

Demolition of cement concrete ( unreinforced) in gd floor and paving n.exc 15 cm thickness below or above the ground level complete all as specified & as directed.

M&L for 40 mm thick cement concrete 1:2:4, type B-1 (using20mm graded stone aggregate) as in flooring, finished cement concrete surface even and smooth with using extra cement complete all as specified & as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified & as directed.

M&L for coloured Non skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15 mm thick screed bed in CM (1:6) complete all as specified & as directed.

M&L for coloured Non skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including screed bed or bedding layer of mortar 20 mm thick in CM (1:6) for laying floor finishes complete all as specified & as directed.

M&L for coloured Non skid ceramic tiles 7 to 8 mm thick (square/ rectangular) polished, on vertical surfaces such as skirtings, dados and risers to steps etc. . set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick backing coat in CM 1:4 all as specified and directed.

M&L for 75 mm thick cement concrete 1:4:8, type D-2 (using 40mm graded crushed stone aggregate) as in sub-base complete all as specified & as directed.

M&L in repair Chequered cement concrete tiles 20cmx2ocmx25mm thick with grey cement and pigment in floors etc set and jointed in neat cement slurry and pointed with white cement and coloured pigment to match the tiles over 15mm thick screed bed in CM 1:6. complete all as specified and directed.

S&F sand stone slabs 50 mm thick as in sun shades, chhajas, shelves, landings cover stone etc n.exc 2mtr in length set in pointed in cement mortal 1:4 complete all as specified & as directed.

M&L for preparation of newly plastered surfaces and applying three coats of white wash on ceiling complete all as specified & as directed.

M&L cement concrete1:3:6, type C-2 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed

S & F Joist, channel, angle, post or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated Fe-410W(GdeE-250) quality B complete all as specified and directed

S & F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and directed

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendents, regulators, sockets, lamp holders, light fitting etc removing materials to store for keeping in safe custody for taking credit or reuse serviceable fittings/fixtures and making good the disturbed surfaces of wall/floors complete all as specified & as directed.

M&L for Point wiring in concealed conduit with 1.5 Sqmm PVC insulated flame retardent low smoke(FRLS) single core stranded copper conductor for one light/fan/bell point in and including PVC conduit 19/20 mm dia to be terminated in pressed steel terminal boxes with 3 mm thick bakelite sheet top cover including 1.5 sqmm PVC insulated "Flame Retardent Low Smoke"( FRLS)" single core stranded copper earth continuity conductor controlled by one switch and/or one regulator complete all as specified and directed. (Wiring shall be made as per colour code in IS for Phase, neutral and earth)

All as per Item No. 107 above but for one socket outlet 5/6 Amps on independent bd controlled by one switch.

All as per Item No. 107 above but for one socket outlet 5/6 Amps controlled by one switch on same board with other switches

All as per item No 107 above but one socket out let 15/16 Amps controlled by one switch on independent board and wiring with 2.5sqmm cable.

S&F switch piano flush type single pole, 5/6 Amps one way, 230 volts, complete all as specified & as directed.

S&F switch piano flush type single pole, 15/16 Amps one way, 230 volts, all as directed complete all as specified & as directed.

S& F socket outlet 5/6 Amps flush type piano 5 pin 230 volts complete all as specified & as directed.

S&F socket outlet 15/16 Amps multipurpose 3 pin 230 V complete all as specified & as directed.

S&F ceiling rose surface bakelite 62.5 x 25 mm size 3 terminals complete all as specified & as directed.

S&F lamp holder , insulated body ,with back plate suitable for batten fitting complete all as specified & as directed.

S&F electronic steping up type ceiling fan regulator suitable to operate at 230 volts 50 Hz, AC supply complete all as specified & as directed.

Supply & fix in replacement surface/wall mounting LED batten 20 watt luminaire having Aluminium housing and integrated electronic driver with mounting accessories complete with lamp holders fixed to wall/ ceiling with fixing accessories and connecting up with & including twin twisted copper flexible wire of size 0.75 sqmm from ceiling rose to fittings complete all as specified & directed. Make:- Havells cat part No-LUMILINEPLUSBS20WLED865SPCSS or equivalent Model of Philips/Bajaj/CG as approved by GE.

Supply & fix in replacement, outdoor street light LED 40 watt luminaire white powder coated with extruded grey aluminium housing and robust construction with reflector cover pre anodised and flat white high transmission acrylic cover or toughened glass, natural white type with electronic driver, connector block etc with internally prewired fixed to building with and including 1.20M long bracket made out of 40mm dia light grade GI pipe bent to shape & providing clamps 2 Nos made out of 50 x 6 mm Flat iron/MS clamps & 12mm dia bolts, nuts & washers etc and connecting up with & including twin twisted copper flexible wire from ceiling rose to fittings complete all as specified & directed. Make:- Havells cat part No- ENDURAPEARLNEOSL40WLED757PASYTOPC or equivalent as approved by GE.

Taking down care fully sub main wiring / service connections of any size including batten/ conduit, and making good the disturbed surfaces of wall/ floor .

M&L sub main wiring of two single core PVC insulated unsheathed stranded copper conductor cables of size 6 Sqmm, 1100 volts grade drawn through and including 20mm dia PVC concealed conduit of 1.2 mm wall thickness including all fixing accessories, and 2.5sqmm PVC insulated stranded copper conductor cable as earth wire(green colour) connected to earth dolly complete all as specified and directed. (Phase-Red, Neutral – black in colour of cable) Note:- Both running cables including earth wire shall be measured & paid for as single length.

Taking down distribution boards any size any type including MCB TPN/SPN/SP etc and making good the disturbed surfaces complete all as specified & as directed.

S&F in replacement of unserviceable MCB DB sheet metal enclosure single pole and neutral 415 V with 200 Amps standard bus bar of suitable size and common neutral link and earth bar all enclosed on standard steel sheet flush mounting type double door factory fabricate complete without MCB and with encosure blank plates for unused way suitable for 8 way flush in wall complete all as specified & as directed.

S & F MCB SPN 40 Amps 240 Volts C, series complete all as specified and directed

S & F MCB 6 to 20 Amps SP, 240 Volt C, series complete all as specified and directed.

M & L earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm size, buried directly in ground (earth pit not less than 2.25 M deep below normal ground level) with top edge of the plate not less than 1.5 M below normal ground level connected to and including galvanised steel earth lead wire of 4 mm dia, including 15 mm bore GI light grade protection pipe upto 1 Mtr above the floor level of the buildings where main switch, DB etc, situated, earth lead wire connected to the earth plate by means of GI bolts, nuts, washers and earth plate surrounded by 150 mm thick alternate layers of charcoal or cock dust mixed with common salt 20 mm bore medium grade GI watering pipe PCC pit in PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate) cover of precast RCC 1:2:4 type B-1(using 20 mm graded stone aggregate) duly reinforced with 8 mm formed or twisted bars @ 100 mm c/c both ways, GI wire mesh, GI sheet funnel necessary excavation in soft/ Looose soil and deposited the surplus soil to a distance not exceeding 50 mtr away from starting point, all as per electrical plate no:3 of SSR part-1 .

Supply and fix XLPE insulated armoured heavy duty multistranded electric cable with aluminium LT conductor 1100 volts grade ISI marked laid in trenches, fixed to wall, poles etc all as specified and directed of size 16 sqmm 2 core.

M&L sub-class 'B' bricks, well burnt, laid breadth wise along the length for cable laid in trenches over sand cushion laid for UG Cable protection, complete all as specified and as directed.

M&L for sand cushioning dry fine for cable cushioning 8 cm below the cable and 15 CM above cable complete all as specified & as directed.

M&L sub main wiring of two single core PVC insulated unsheathed stranded copper conductor cables of size 4 Sqmm, 1100 volts grade drawn through and including 20mm dia PVC concealed conduit of 1.2 mm wall thickness including all fixing accessories, and 2.5sqmm PVC insulated stranded copper conductor cable as earth wire(green colour) connected to earth dolly and making good the disturbed surface complete all as specified and directed. (Phase-Red, Neutral – black in colour of cable) Note:- Both running cables including earth wire shall be measured & paid for as single length.

Supply and fix MCB DB sheet metal enclosure factory fabricated SINGLE door SPN 2 way with 200 amps rated bus bar 240 volts complete all as specified and directed.

M/S Solanki Brothers

SahaDevSingh Constructions

M/s J S & SONS

kedar nath

Balaji Associates

3Krishna Enterprises

Narendra & Co.