REPAIR RE CANNING PAINTING AND POLISHING TO WOODEN AND STEEL FURNITURE ITEMS AT AF STN JAMMU UNDER GE AF JAMMU

Amount

Taking down worned out/unsv components of the following wooden/steel furniture items, Supply and fix new component without any crack/any defects as pe shape and size specified on respective drawings and as directed by Engineer-in-Charge. WOODEN FURNITURE:- CHAIR DINING (FD-203/279)

Replacement of u/s Rear Legs of chair dining with new rear legs of seansoned hard wood free from cracks and knots, shape and size as shown on drawings

Descrption all as per ser item No 1(1.01) above but Front Legs

Descrption all as per ser item No 1(1.01)above but Side rail with holes for weaving (spacing of holes shall be as per old one)

Descrption all as per ser item No 1(1.01)above but Front/back rail with holes for weaving (spacing of holes shall be as per old one)

Descrption all as per ser item No 1(1.01) above but Bottom stiffener

Descrption all as per ser item No 1(1.01) above but Back stiffener

Provn of four Nos of wooden tringular bracket of size 75mm x 75mm to each chair made out 25mm thick hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge

PVC/Rubber Shoe as per sample approved

Re-canning of Chair dining as per Godrej pattern with 2 mm wide half round superior quality cane plastic after taking out existing cane. Border of canning shall be woven with 4 mm half round plastic cane of superior quality as shown in drawing and directed by Engineer-in-charge.

CHAIR DINING MAP (FD/MAP-II/05)

Replacement of u/s Rear Legs of chair dininng with new rear legs of seansoned hard wood free from cracks and knots, shape and size as shown on drawings

Descrption all as per ser item No 2(2.01) above but Front Legs

Descrption all as per ser item No 2(2.01) above but Bottom stiffener

Descrption all as per ser item No 2(2.01) above but Back stiffener

PVC/Rubber Shoe as per sample approved

Replacement of u/s PVC Seat with new PVC seat 4mm thick of PPCP material and weight not less than 0.50 kg with perforated holes shall be fixed in side the frame of seat with proper screws , PVC sheet of superior quality as shown in drawing and directed by Engineer-in-charge.

CHAIR WRITING WITH CUSHION (FD-1107)

Replacement of u/s Rear Legs of chair writing with cushion new rear legs of seansoned hard wood free from cracks and knots, shape and size as shown on drawings

Descrption all as per ser item No 3(3.01) above but Front Legs

Descrption all as per ser item No 3(3.01) above but side rail

Descrption all as per ser item No 3(3.01) above but front/back rail

Descrption all as per ser item No 3(3.01) above but Bottom stiffener

Descrption all as per ser item No 3(3.01) above but Back stiffener

Descrption all as per ser item No 3(3.01) above but Arm rest

Provn of one Nos of bottom cushion seat fixed on a frame with cover of size as per drawing shall be fixed with screws on chair as directed by Engineer-in-Charge

PVC/Rubber Shoe as per sample approved

Provn of one Nos of back cushion seat fixed on a frame with cover of size as per drawing shall be fixed with screws on chair as directed by Engineer-in-Charge

CHAIR DINING MAP (OFFICER) (FD/MAP-II/04)

Replacement of u/s Rear Legs of chair dining with new rear legs of seansoned hard wood free from cracks and knots, shape and size as shown on drawings

Descrption all as per ser item No 4(4.01) above but Front Legs

Descrption all as per ser item No 4(4.01) above but side rails

Descrption all as per ser item No 4(4.01) above but front rails

Descrption all as per ser item No 4(4.01) above but stifeners

Descrption all as per ser item No 4(4.01) above but teak wood stopper for support of the cushion and seat ply

Descrption all as per ser item No 4(4.01) above but 75mm thick 40 density cushion of approved from (Kurlon/Sleepwell) covered with approved tapestry cloth shall be fixed over 12mm thick ply as spacified in drawing

PVC Rubber Shoe as per sample approved

SOFA SET 4 Seater (FD-281/373)

Replacement of arms made out of teak wood duly french polish as per drawing complete.

Replacement of front legs of sofa set made out of teakwood duly french polish as per drawing complete.

Replacement of rear legs of sofa set made out of teakwood duly french polish as per drawing complete.

PVC Rubber Shoe as per sample approved

Foam cushion for sofa set size 525x525x100mm, 40 density, Make-Sleepwell duly covered with best quality tapestry cloth as approved by Engineer-in-Charge complete all as directed and specified Note:- Rate of tapestry cloth shall not be less than Rs 250/- per RM

SOFA SET 5 Seater (FD-281/373)

Replacement of arms made out of teak wood duly french polish as per drawing complete.

Replacement of front legs of sofa set made out of teakwood duly french polish as per drawing complete.

Replacement of rear legs of sofa set made out of teakwood duly french polish as per drawing complete.

PVC Rubber Shoe as per sample approved

Foam cushion for sofa set size 525x525x100mm, 40 density, Make-Sleepwell duly covered with best quality tapestry cloth as approved by Engineer-in-Charge complete all as directed and specified Note:- Rate of tapestry cloth shall not be less than Rs 250/- per RM

BED PLYTOP WOODEN (FD 246/247)

Head rest as shown on drawing

Foot Rest as shown on drawing

Long rail made of Ist class hard wood

Short rail made of Ist class hard wood

Stiffener made of Ist class hard wood

Replacement of unsv legs with new seasoned teak wood

Right angled MS bracket 200mm long x 25mm wide x 3mm thick duly fixed with screw

12mm thick BWR Ply wood top in one piece

CHAIR WRITING (FD-261/280)

Rear legs

Front Legs

Side rail with holes for weaving (spacing of holes shall be as per old one)

Front/back rail with holes for weaving (spacing of holes shall be as per old one)

Bottom stiffener

Back stiffener

Arm rest

Provn of four Nos of wooden tringular bracket of size 75mm x 75mm to each chair made out 25mm thick hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge

PVC/Rubber Shoe as per sample approved

Re-canning of Chair Writing as per Godrej pattern with 2 mm wide half round superior quality cane plastic after taking out existing cane. Border of canning shall be woven with 4 mm half round plastic cane of superior quality as shown in drawing and directed by Engineer-in-charge.

CHAIR EASY (FD-229)

Rear Leg

Front Leg

Side Rail

Front/Back Rail

Back Stiffener

Bottom Stiffner

Arms rest

PVC/Rubber Shoe as per sample approved

Re-canning of Chair easy as per Godrej pattern with 2 mm wide half round superior quality cane plastic after taking out existing cane. Border of canning shall be woven with 4 mm half round plastic cane of superior quality as shown in drawing and directed by Engineer-in-charge.

TEAPOY (FD-278/382)

Long rail

Short rail

Side stiffener

Centre stiffener

Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved by Engineer-in-charge. Sides of the MDF board shall be fixed with PVC edge band tape duly matched the colour with the board all as directed.

PVC/Rubber Shoe as per sample approved

Provn of eight Nos of wooden tringular bracket of size 75mm x 75mm to each teapoy made out 30mm thick hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge

PEG TABLE (FD-236/277/384)

Long rail

Short rail

Side stiffener

Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved by Engineer-in-charge. Sides of the MDF board shall be fixed with PVC edge band tape duly matched the colour with the board all as directed.

PVC/Rubber Shoe as per sample approved

TABLE WRITING (FD-275)

Long rail

Short rail

Drawer made out prelaminated MDF board and 6mm thick commercial ply at bottom and fitted with one 100mm chromium plated handle

Bottom centre stiffener

Bottom side stiffener.

Provn of six Nos of wooden tringular bracket of size 75mm x 75mm to each Table made out of 25mm thick hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge

Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved by Engineer-in-charge. Sides of the MDF board shall be fixed with PVC edge band tape duly matched the colour with the board all as directed.

PVC/Rubber Shoe as per sample approved

TABLE 900mm x 600mm with drawer and without drawer (FD-283/284)

Long Rail

Short Rail

Bottom Side stiffener

Bottom Centre stiffener

Drawer made out prelaminated MDF board and 6mm thick commercial ply at bottom and fitted with one 100mm chromium plated handle

Provn of six Nos of wooden tringular bracket of size 75mm x 75mm to each Table made out of 25mm thick hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge

Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved by Engineer-in-charge. Sides of the MDF board shall be fixed with PVC edge band tape duly matched the colour with the board all as directed.

PVC/Rubber Shoe as per sample approved

TABLE DINING 6/8 PERSON( FD-239/273,376,FD-30)

Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved by Engineer-in-charge. Sides of the MDF board shall be fixed with PVC edge band tape duly matched the colour with the board all as directed.

Long rail

Short rail

Stiffener

Provn of eight Nos of wooden tringular bracket of size 75mm x 75mm to each Table made out of 40mm thick hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge

PVC/Rubber Shoe as per sample approved

TABLE DRESSING LADIES (FD-251/378/395)

5mm thick Mirror of size 365mmx1220mm with Back ply of 6mm thick commercial plywood and wooden frame of existing shape & size. Make- Saint Gobin/Gold plus

Sliding glass shutter of 3mm thick as per existing.

Drawer of 6 mm thick ply wood commercial with 18mm pre-laminated MDF board as per existing shape and size

Knob as per sample approved

TABLE BED SIDE (FD-248 /276)

Top 18/19mm thick both side prelaminated MDF board fixed with PVC edge band tape

Side made of 18/19mm thick both side prelaminated MDF board fixed with PVC edge band tape

Shelf made of 18/19mm thick both side prelaminated MDF board fixed with PVC edge band tape

Bottom made of 18/19mm thick both side prelaminated MDF board fixed with PVC edge band tape

Back shall be made of 6mm thick ply wood commercial as per existing shape and size and shown in drgs and directed

Leg frame with 4 Nos leg and stiffener as per drawing made Ist class hard wood (teak) duly french polished.

TABLE CENTRE (FD-274/375)

Long rail

Short rail

Side stiffener

Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved by Engineer-in-charge. Sides of the MDF board shall be fixed with PVC edge band tape duly matched the colour with the board all as directed.

PVC/Rubber Shoe as per sample approved

TABLE DRESSING GENTS(FD-230/379)

Looking glass complete with frame and back ply. As per drawing Make- Saint Gobin/ Gold Plus

Drawer of 6 mm thick ply wood commercial with front 18mm pre-laminated MDF board and Knob as per existing shape and size

Provision and replacement of CP knobs 32mm in brown colour as per sample

Side board (FD-26,FD-371,& FD-372)

Provision and replacement of sides of the side prelaminated particle board 18mm board veneered

Provision and replacement of old/UNSV drawer with teak wood sides and pre-laminated particle board 18mm thick on front and plywood 6mm thick commercial quality at the bottom. Make :- Kitply, Greenply, Archidply

Provision and replacement of doors of the side board made of pre-laminated board 18mm thick with teakwood edging door fixed with piano hinges. Make :- Kitply, Greenply, Archidply

Provision and replacement of top made out of pre-laminated particle board 18mm thick.

Provision and replacement of bottom frame made of 18mm thick teak wood and fixed with screws all as shown on drawings.

Provision and replacement of hard wood legs of side board all as per drawings.

Provision and replacement of CP knobs 32mm in brown colour as per sample

Table Bed side MAP (FD/E6/MAP/15(R)

Provision and replacement of drawer on 18mm Thick Pre laminated Partical board with telescopic channel as per drawings .

Provision and replacement of 18mm Thick Pre laminated Partical board top with PVC edging fixed to frame (25mm projection on three spaces) as per drawings.

Provision and replacement of 18mm MS square pipe(500mmx450mm) (18 gauge) black powder coated as per drawings.

Provision and replacement of handles as per drawings and sample apporoved by Engr-in-charge.

Table Dressing Ladies MAP (FD/MAP-II/07)

5mm thick electro copper plated mirror shall be fixed/replace over 6mm thick plywood back.

Replacement of sides with new sides of 18mm thick pre-laminated MDF board.

Replacement of sides with new top of 18mm thick pre-laminated MDF board.

Replacement of sides with new back of 18mm thick pre-laminated MDF board.

Replacement of sides with new front of 18mm thick pre-laminated MDF board.

Replacement of bottom of side units with 12mm thick commercial plywood.

Side and back drawers to be repaired with 12mm thick pre-laminated MDF board.

Replacement of old/unsv knobs of drawers.

Replacement of vertical hardwood members of size 45mm x 30mm.

Replacement of horizontal support of size 30mm x 20mm.

Stool of dressing table - Replacement of heavy duty revolving nylon double wheels at base.

Replacement of seat of the with 75mm thick foam of 40 density coverd with tapestry cloth as approved by Engr-in-charge.

Mirror Dressing Gents (FD/E6/MAP/16)

Replacement of looking mirror of size 5mm thick fixed inside the teakwood frame made out of the 38mm x 25mm section as per drawing.

Replacement of teak wood beading of size 6mm thick around the edges of shutter and drawer.

Replacement of glass shelves of 5mm thickness to be fixed inside the box as shown in drawing.

Replacement of the old hasp & stapples.

Replacement of old/UNSV magnetic catchers.

Table card 900 x 900mm (FD-88,352)

Top of the table made out of partical board 18mm thick with 1mm pre-laminated exterior grade with teakwood beading all-around duly polished as per drawing.

Legs of table as per drawing

Long rail of table as per drawing

Stiffeners H type of the table as per drawing

PVC/Rubber Shoe as per sample approved

Table Dining 120 x 90cm (FD/MAP-II/03)

Replacement of top of table with 18mm thick BWR plywood of grade A with 1mm thick laminated sheet pasted over the ply with suitable screws from under neath, edges of top shall be coverd with 6mm thick teak wood as per drawing.

Replacement of wooden corner brackets made to shape of size 100mm x 100mm x35mm thick.

Replacement of long rails as per drawing

Replacement of short rails as per drawing

Replacement of legs as per drawing

PVC/Rubber Shoe as per sample approved

Polishing of Wooden Furniture Item : All wooden and steel surfaces of the following furniture items wheather exposed to view or not when placed in position shall be polised with high gloss french polish and painted with high glossy paint to be finished as directed by Engineer-in-Charge duly preparation of surface with emery paper and applying putty as and where required:-

CHAIR DINING (FD-203/279)

CHAIR DINING MAP (FD/MAP-II/05)

CHAIR WRITING WITH CUSHION (FD-1107)

CHAIR DINING MAP (OFFICERS) (FD/MAP-II/04)

Sofa four seater (FD-281)

Sofa 5 seater (FD-281/373)

BED PLYTOP WOODEN (FD 246/247)

CHAIR WRITING (FD-261/280)

CHAIR EASY (FD-229)

TEAPOY (FD-278/382)

PEG TABLE (FD-236/277/384)

TABLE WRITING (FD-275)

TABLE 900mm x 600mm WITH DRAWER and WITHOUT DRAWER (FD-283/284)

TABLE DINING 06/08 PERSON( FD-239/273)

TABLE BED SIDE (FD-248 /276)

TABLE CENTRE (FD-274/375)

TABLE DRESSING LADIES (FD-251/378/395)

TABLE DRESSING GENTS(FD-230/379)

Side board (FD-26,FD-371,& FD-372)

Table Bed side MAP

Table Dressing Ladies MAP (FD/MAP-II/07)

Mirror Dressing Gents (FD/E6/MAP/16)

Table card 900 x 900mm (FD-88,352)

Table Dining 120 x 90cm (FD/MAP-II/03)

STEEL FURNITURE Charpoy GI Pipe (FD-220)

3 way Galvanized Iron Elbow 32 mm dia. Note weight of each elbow shall not be less than 450 gm

Galvanized iron check nut 32mm dia.Note:-weight of each check nut shall not be less than 125gm

Long rail of 32 mm dia galvanized iron pipe medium grade incl threading at both ends as directed

Short rail converted out of retrieved Long rail, Item No 1(c) above incl cutting, threading as required and directed

Leg converted out of retrieved Short rail, Item No 1(d) above incl cutting, threading as required and and directed

Provn of Two Nos MS cleat as shown on drg to hold the MNF set and one MS plate at the bottom to each Leg converted out of retrieved Short rail

Provision of two no 6mm thick x 50 mm width MS flat strip of 900 mm long by drilling four nos screw to long rail. All as specifed.

12mm thick ply wood top BWR Grade ISI Marked of size 1950mm x 900mm (Single piece) Make Kitply, centurey and equalent including replacement of old plywood or newar.

BED HARD STEEL (FD/E6/MAP/08(R)

12mm thick ply wood top of size 1950mm x 900mm (Single piece) BWR Grade ISI Mark with MS screws, complete all as specified Make Kitply, centurey and equalent

Replacement of 18mm thick prelaminated particle board at head side of the bed as specified

Replacement of 18mm thick prelaminated particle board at foot side of the bed as specified

PVC shoes at the bottom of leg.

CHAIR COMPUTER (FD/E6/MAP/01)

Replacement of complete seat with new moulded foam cushioned 40mm density as shape and size covered with tapestry cloth as approved along with PVC liping all round, complete all as specified

All as per item No 28.01 here-in-before but for back frame

Replacement of Hand rest one piece made of black integral skin,reinforced with MS insert it. Hand rest have slope towards front as specified

Replacement of Pedestal assembly complete

Replacement of Twin wheels coasters (set of five) press fitted at the bottom of leg.

CHAIR WRITING MAP (FD/E6/MAP/12)

Replacement of exising tapestry of seat frame with new tapestry cloth of seat frame approved by Engr-in-charge with PVC liping all round complete all as specified and directed by Engr -in charge Note- Cost of tapestry not less than Rs 250/ RM.

All as per item No29.01above but for back frame

Replacement of Hand rest one piece made of black integral skin,reinforced with MS insert it. Hand rest have slope towards front as specified

Replacement of complete seat and back with new moulded foam cushioned 40mm density as shape and size, covered with tapestry cloth as approved along with PVC liping all round, complete all as specified

Rubber stopper at the bottom of leg.

Chair Verandah MAP(FD/MAP-II/06)

Taking out old U/S PVC seat and back and rubber shoes from chair verandah, removing of foreign materials from the iron frame by rubbing with sand paper, painting two coats with white synthetic enamel paint and replace PVC seat and back with 4 mm thick of weight not less that 1.85 Kgs and PVC ribs on seat and back of superior quality as directed by Engineer-in-Charge

PVC/Rubber shoes as per sample approved

CHAIR REVOLVING LONG/LOW BACK

Replacement of complete seat with new moulded foam cushioned 40mm density as shape and size covered with letherate as approved along with PVC liping all round, complete all as specified

All as per item No 31.01 here-in-before but for back frame

Replacement of Hand rest one piece made of black integral skin,reinforced with MS insert it. Hand rest have slope towards front as specified

replacement of Pedestal assembly complete with hyradlic shocker as directed by Engr-in-charge

Replacement of Twin wheel coasters press fitted at the bottom of leg.

ALMIRAH LARGE STEEL WITH SHELVES (FD-351/1031) /Almirah Small/ Medium steel (FD-350 /1032/243)/ Locker Bedside Steel (FD-257/1029) :-

Shutter (Single Leaf) for Almirah Large Steel made of 1.6 mm thick MS sheet and shall be applied a coat of red oxide primer on both side after preparation surfaces

All as per Item 32.01 here-in-before but for Almirah Small/medium steel

All as per Item 32.01 here-in-before but for Locker Bedside Steel

Shelves made of 1.25 mm thick MS sheet and shall be applied a coat of red oxide primer on both side after preparation surfaces for almirah Large steel

All as per Item 32.04 here-in-before but for Almirah Small/medium steel

All as per Item 32.04 here-in-before but for Locker Bedside Steel

Six Levers brass lock for Almirah Large Steel/Almirah small/Med Steel Make : Godrej/Harrison/Link with duplicate keys

Three way Locking Device for Almirah Large Steel of 10 mm dia MS rod as per trade pattern incl a coat of red oxide primer

All as per Item 32.05 here-in-before but for Almirah Small/medium steel

Chromium plated Steel Handle 125mm for Almirah Large Steel/Almirah small/Med

Chromium plated MS Key plate fixed with screw and nuts for Almirah Large Steel/Almirah small/Med

Chromium plated 100mm Steel Handle 'D' type for Locker Bedside steel

Leg for Almirah Large Steel/Almirah small/Med Steel made of 1.6 mm thick MS sheet with Gas welding incl a coat of red oxide primer

75mm Chromium plated haps & stapple fixed with rivets of locker steel

Hanging Rod for Locker bed side steeel of 1.6mm thick chromium plated MS Rod

CHAIR CB STEEL WITH ARMS/WITHOUT ARMS ( FD-75(M)

Seat frame of Chair CB Steel with Arms of 1st class hard wood duly polished with high class black polish incl weaving with 2 mm wide half round plastic cane with Godrej pattern & border with 3 mm wide plastic cane superior quality fixed as shown in drawing

All as per item No (33.01) here-in-before but back frame

All as per item No(33.01) here-in-before but Seat frame for Chair CB Steel without Arms

All as per item No (B305.01) here-in-before but back frame

Arms rest for Chair CB Steel with Arms of 1st class hard wood duly polished with high class black polish

PVC cap at top of the frame of the chair (02 Nos to each chair)

PVC Shoe at bottom of the frame of the Chairs (04 Nos to each chair)

TABLE OFFICE CLERK/TYPIST STEEL (FD-84(M)/1004/FD-1006)

Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved by Engineer-in-charge. Sides of the MDF board shall be fixed with PVC edge band tape duly matched the colour with the board all as directed.

Drawer made of 22 gauge MS sheet with a coat of red oxide primer

Six levers Lock of Godrej/Harrison with duplicate keys.

Cutting down wornout portion of MS Tube of the steel frame and replace with 25mm dia 1.6mm wall thickness MS tube in one piece not less than 250mm duly welding to bring into original size as per drawing, applying of red oxide primer after preparation of surface. Upto 300mm long and piece will be counted as one.

PVC Shoe at bottom of the leg of the Table

TABLE OFFICE OFFICER STEEL (FD-84(M)/1003)

Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved by Engineer-in-charge. Sides of the MDF board shall be fixed with PVC edge band tape duly matched the colour with the board all as directed.

Drawer made of 22 gauge MS sheet with a coat of red oxide primer

Six levers Lock of Godrej/Harrison with duplicate keys.

Cutting down wornout portion of MS Tube of the steel frame and replace with 25mm dia 1.6mm wall thickness MS tube in one piece not less than 250mm duly welding to bring into original size as per drawing, applying of red oxide primer after preparation of surface. Upto 300mm long and piece will be counted as one.

PVC Shoe at bottom of the leg of the Table

CHAIR executive long back lethaerate (TP)

Replacement of complete seat with new moulded foam cushioned 40mm density as shape and size covered with letherate as approved along with PVC liping all round, complete all as specified

All as per item No (36.01.01) here-in-before but for back frame

Hand rest one piece made of black integral skin,reinforced with MS insert it. Hand rest have slope towards front as specified

Pedestal assembly complete with hyradlic shocker as directed by Engr-in-charge

Twin wheel coasters press fitted at the bottom of leg.

Briefing chair with writing pad complete Godrej PCH-1712

Re-canning of Chair Writing as per Godrej pattern with 2 mm wide half round superior quality cane plastic after taking out existing cane. Border of canning shall be woven with 4 mm half round plastic cane of superior quality as shown in drawing and directed by Engineer-in-charge.

Replacement of writing pad with new MDF board writing board and directed by Engr-in-charge.

Writng Pad fix with sutable screws

Rubber stopper at the bottom of leg.

Charpoy IP Hardtop (FD/MAP-II/01)

Replacement of old/Unsv plywood with 12mm thick commercial plywood with proper nut and bolt of size as per drawing

PVC hard rubber shoes

Chair School with Hand Board (FD/E-6/MAP/05)

Replacement of old/Unsv one piece PVC seat and back of size as per drawing

Replacement of old/Unsv hand board with 18mm thick prelaminated particle with PVC edging (hinged on right hand side screwed to 25mm hollow steel pipe inserted in 20mm MS rod welded to fame) of size as per drawing.

PVC rubber shoes

Chair Verandah (FD-256, 259, 359)

Taking out old U/S cane/newar and rubber shoes from chair verandah, removing of foreign materials from the iron frame by rubbing with sand paper, and welding UNSV frame, painting two coats with white synthetic enamel paint and recanning seat and back with 4 mm wide half round white plastic cane of superior quality as directed by Engineer-in-Charge

PVC/Rubber shoes as per sample approved

Table Computer FD/E6/MAP/03

Provision and replacement of top 18mm Thick Pre laminated Partical board as per drawings.

Provision and replacement of18mm Thick Pre laminated Partical board drawer 75mm deep on telescopic channel as per drawings.

Provision and replacement of18mm Thick Pre laminated Partical board key board tray on telescopic channel as per drawings.

Provision and replacement of 25 mm thick sqare pipe side support of Table computer as per drawings.

Provision and replacement of legs with nylon buffer of Table computer as per drawings.

Painting of Steel Furniture Item : All steel surfaces of the following furniture items wheather exposed to view or not when placed in position shall be painted with high glossy paint to be finished as directed by Engineer-in-Charge duly preparation of surface with emery paper and applying putty as and where required:-

BED HARD STEEL (FD/E6/MAP/08(R)

CHAIR WRITING MAP (FD/E6/MAP/12)

Chair Verandah MAP(FD/MAP-II/06)

ALMIRAH LARGE STEEL WITH SHELVES

Locker Bed Side steel

Almirah small/medium steel

CHAIR CB STEEL WITH ARMS/WITHOUT ARMS ( FD-75(M)

TABLE OFFICE CLERK/TYPIST STEEL (FD-84(M)/1004/FD-1006)

TABLE OFFICE OFFICER STEEL (FD-84(M)/1003)

Briefing chair with writing pad complete Godrej PCH-1712

Charpoy IP Hardtop (FD/MAP-II/01)

Chair School with Hand Board (FD/E-6/MAP/05)

Chair Verandah (FD-256, 259, 359)

Table Computer FD/E6/MAP/03

SCHEDULE 'A' PART-II (Schedule of credit) Credit amount of Rs (Refer schedule of credit) for retrieved material mentioned in Sch 'A' Part-II of Tender documents in PDF form will be deducted offline during acceptance of tender of lowest bidder.

M/s Sunny Gupta (BID ID -3487326)

JAINCO STEEL INDUSTRIES (BID ID -3487731)

VEE KAY IND (BID ID -3485221)