SPECIAL REPAIR TO ROOF, TOILETS, MAIN HALL AND BALCONY OF BLDG NO P-12 UNDER GE WEST MATHURA

Amount

Taking down chowkhats with shutter (without taking off shutters from the frame) area not exc. 1.50 Sqm each complete all as specified and directed.

Taking down chowkhats with shutter (without taking off shutters from the frame) area exc. 1.50 Sqm but n.exc 4.00 sqm each complete all as specified and directed.

S&F 140mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F aluminium anodised barrel tower bolts, 150mm long of extruded section complete all as specified and directed.

S&F 100mm long stainless steel handles, oval type complete all as specified and directed.

S&F for 40mm thick flush shutter solid core construction with block board core & ply wood face panels, commercial type on both faces complete all as specified and directed by Engineer-in-charge.

M&L for preparation of new wooden or wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-Charge.

S&F decorative laminate type 1, 0.9mm thick of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and directed.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube complete all as specified & shown in relevant drawing of item No. 08095 in MES Schedule (Part-II) and directed by Engineer-in-Charge.

S&F Factory Made Solid PVC Moulded Door Shutters 28 to 30 mm thick (stile:), with particle board core and 2,4 or 6 raised panel design with 5mm thick Moulded PVC Sheet on the front Face & 5mm Plain colour PVC sheet on back face, fixing in frame at site complete specification & drawing as per SSR complete all as specified and directed.

M&L for preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-charge.

Dismantling brick/PCC terracing tiles single layer from roof laid and pointed in cement mortar ncluding cleaning and stacking serviceable tiles for re use and balance removing/disposal off from the site complete all as specified and as directed by Engineer-in-charge.

Demolition of mud or bricks in roofs any thicknees and in any position and leaping over roof terrace removing the demolished material to a distance exc 250 m n,exc 500 m and depositing where directed at a lavel n, exc 1.5 m above starting point, complete all as specified and as directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off premises outside MoD land complete all as specified and directed.

M&L for vitrified ceramic tiles dark shed/double charged/ultracharged 8-10mm thick (square/ rectangular) polished area of each tile exceeding 0.42sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick cement screed bed in CM (1:4) complete all as specified and directed.

All as per item No 15.00 (here-in-before) above but as in skirting over 10mm thick backing coat in CM (1:3) complete all as specified and directed.

M&L for Non skid Ceramic coloured tiles 7-8 mm thick (square/ rectangular) polished, area of each tiles exc 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 15mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L Coloured Glazed ceramic tiles in vertical surface 450x300x7 mm with highlighter thick set and jointed in neat cement slurry and pointed in white or colour cement to match incl 10mm thick plaster in cement mortar (1:3) complete all as specified and directed.

M&L for 18-20mm thick Granite (of any type, shade and colour as appoved by GE), work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like including 20mm screed bedding in cement mortar (1:4) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

Rounding (half round) to edges of garnite slabs one edge, such as in steps, cooking platform, and other similar situations etc complete all as specified and directed.

M&L for 18-20mm thick Granite (of any type, shade and colour as appoved by GE), including both side polished, roughening fully rounded edges, fixed to wall as in urinal partition complete all as specified and as directed.

Taking down cement plaster on brick or stone walls etc. including racking out joints, hacking for key, scrubbing down with water, any description etc. complete all as specified and as directed.

M&L for rendering 15 mm thick in CM 1:4 including water proofing compound on fair face of brick or concrete surface, finished even and smooth without using extra cement complete all as specified and directed. Note : Supply only WPC shall be measured and paid seperately.

M&L for rendering 15mm thick on other than fair faces of brick work or concrete surfaces in cement mortar (1:6) finished even and fair without using extra cement complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified and directed.

M&L for rendering 5mm thick in CM (1:4) as on ceiling complete all as specified and directed.

M&L for preparation of new plastered surface of wall and applying two coats of acrylic distemper over one coat of primer over 1mm thick wall care putty complete all as specified and directed.

M&L for preparation of new plastered surface of wall and applying two coats of cement base paint over a coat of cement base primer complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for preparation of old treated surfaces of ceiling and applying two coat of white wash complete all as specified and directed.

M&L for complete removal of existing treatment and preparation of old surface of walls and applying two coats of acrylic distemper over one coat of primer including 1mm thick wall care putty on wall etc complete all as specified and directed.

M&L for applying a coat of two component elastomeric acrylic polymer modified cementitious water proofing coating, having properties of 80 % elongation as per ASTM D412, resisting 5 bars hyrostatic pressure as per DIN 1048, reduction to rapid chloride shall be 70 as per DIN 1048, crack bridging upto 1.2mm as per ASTM 4548.5. The mixing ratio of the coating shall be 2 parts of powder & 1 part of liquid without any water addition in the mixing, etc., complete as per manufacturers specifications and sprinkle sand at 10-15 gram per sqft for better grip with plaster complete all as specified and directed.

M&L preparation of new plastered surfaces for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @1.43 litre/10 sqm over and including priming coat of exterior primer applied @0.90 litre/10 Sqm complete all as specified and directed.

M&L for complete removal and preparation of old treated surfaces for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @1.43 litre/10 sqm over and including priming coat of exterior primer applied @0.90 litre/10 Sqm complete all as specified and directed.

S&F GI spout pipe 50 mm dia tubes,light grade galvanised, with all fitting, laid in treanches complete all as specified and as directed.

Cutting holes into or through brick walls not exceeding 15 Sq cm built in mud mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required complete all as specified and directed by Engineer-in-charge.

Taking up or down steel tubing and connections of 15 mm bore pipe complete all as specified and as directed.

Taking up or down steel tubing and connections of 20 mm bore pipe complete all as specified and as directed.

M&L for 15 mm nominal bore Mild steel galvanised water tubing, medium grade, with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

M&L for 20 mm nominal bore Mild steel galvanised water tubing, medium grade, with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

S&F 100mm CI pipes soil, waste and vent pipe in any length with or without ears, with cement joints fixed to wall including applying a coat of black japaned paint on outer surface of pipes including taking down old unserviceable CI pipe and fittings complete all as specified and directed.

S&F 100mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and as directed by Engineer-in-charge.

S&F 100mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified and as directed by Engineer-in-charge.

S&F 100mm CI Branch pieces, single T (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified & directed.

S&F 100mm CI Branch pieces, single T (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door complete all as specified and as directed by Engineer-in-charge.

S&F 75mm CI pipes soil, waste and vent pipe in any length with or without ears, with cement joints fixed to wall including applying a coat of black japaned paint on outer surface of pipes including taking down old unserviceable CI pipe and fittings complete all as specified and directed.

S&F 75mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and as directed by Engineer-in-charge.

S&F 75mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified and as directed by Engineer-in-charge.

S&F 75mm CI Branch pieces, single T (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified & directed.

S&F 75mm CI Branch pieces, single T (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door complete all as specified and as directed by Engineer-in-charge.

M&L for bands, straps, supports or stays for rainwater , Ventilating pipes, including bolts , if required; hooks ( stay), heavy, for large gates; hook and lintle hanges; large hasps and staples ; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters ; knee piece inserts; two way and three ways straps , plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed.

S&F in repair 15mm dia stop cock cast copper alloy, fancy type with, chromium plated long shank and cup with crutch or butterfly handle screwed down high pressure, screwed both ends for iron pipe complete all as specified & directed by Engineer-in-charge. Make : Cat Part No F1015201 of Cera or equivalent in approved makes as specified.

S&F in repair 15 mm bore bib tap, cast copper alloy, chromium plated, long body, fancy type screwed down and screwed for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-charge. Make : Cat Part No F1015151 of Cera or equivalent in approved makes as specified.

S&F in repair PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and as directed.

S&F in repairs vitreous china urinal Half stall type of size 350mm x 340mm x 615mm, white incl CP spreader screwed for iron pipe and fixed complete including providing and fixing plugs with and including 60mm long brass screws, pointed around urinal back in cement, fixing discharge pipe, flush pipe, grating and union for discharge complete all as specified and directed. Make : Cat Part No S4020113 of Cera or equivalent in approved makes as specified.

S&F in repairs towel rail chromium plated 20mm dia ‘D’ type, 600mm long complete all as specified and directed by Eng-in-charge.

S & F rotational moulded polyethylene water storage tank 750 Ltr capacity (cylindrical vertical with closed top) hoisted and fixed in position with all necessary GI fittings complete all as specified in SSR Pt I including taking down old unserviceable water tank, ball valve & tank nipple complete all as specified and directed by Eng-in-charge.

S&F Ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe 20mm bore or brass ferrule and fixed complete all as specified and directed by Engineer-in-Charge.

S&F 20mm GI nipple suitable for HDPE water tank complete all as specified and directed.

S&F in repair Low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc. complete all as specified and directed.

M&L for cutting chases, pining in, making good to facing where required and pointed in CM (1:3) for concealed steel water tubing & like and making good, match with existing surfaces by applying white wash/colour wash cutting not exc 10cm girth complete all as specified and directed.

Demolition of cement (un-reinforced) concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15 cm thickness below or above ground level complete all as specified and directed by Engineer-in-Charge.

S&F in repair Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including setting the trap and pan in concrete and32mm dia PVC flush pipe complete including jointing to socket of flushing rim, complete all as specified and directed.

S&F in repair vitreous china wash down, water closet pan (pedestal pattern), white including fixing bolts and connection to flush pipe and drain out going pipe and closet seat cover black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, CP jet including PVC connection complete all as specified and directed.

S&F in repairs Toilet paper holder with flat recessed type stainless steel complete all as specified and directed by Engineer-in-Charge.

S& F in repair for Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F in repairs PVC 10 ltrs syphonic action type flushing cistern, low level with inlet, ball valve, float and handle including brackets, flush pipe of PVC 32mm bore and connection to WC pan complete all as specified and directed.

M&L decorative mouldings using POP of cross sectional dimension not exc 50 Sqcm as per pattern and design as approved and fixed in position including praparation of surface and applying two coats of oil bound distemper, complete all as specified and directed.

S&F non wooven paper backed vinyle wallpaper digitally print, best quality fixed with best quality of adhesive to wall complete all as specified & directed Note:- Finish,design and colour of wall paper shall be approved by GE.

S & F in repair table top wash hand basin white of size 550 x 440 mm and waste fitting 40mm brass chromium plated and waste pipe and 15mm dia PVC connection with brass nuts complete all as specified and as directed. Make : Cat Part No S2020103 (Cafe) of Cera or equivalent in approved makes as specified.

S&F in repair vitreous china wash basin, white, flat back, size 600mm x 400mm x 120mm including waste pipe and brackets but excluding tapes, chain and plug etc complete all as specified and directed by Eng-in-charge. Make : Cat Part No S2020141 (Cafe) of Cera or equivalent in approved makes as specified.

S&F high clarity mirror for bathroom, built in energy efficient LED strips arround the mirror, anti fog resistance, contact control, touch movement sensors, wall mounted all as specified and directed.

S&F in repairs for stainless steel 25mm dia as in curtain rod including brackets and side holders complete all as specified and as directed.

Providing and fixing of 12 MM Thick Engineer wooden flooring, classification of use 32/23 with a surface abrasion resistance of class AC5 (average 4500 cycles), impact resistance of Class IC2, resistance to cigarette burn with a rating of 5(EN 438-2:05), swelling after 24 hrs in warm water is less then 12%, Modulus of rupture of 53.3 newton/mm2, Internal bond 1.78 newton/mm2, surface soundness 1.01 newton/mm2(EN 13329:2000) with a 0.2 mm thick wear layer on top of a High Density Fiber substrate core (density ~ 948.3 Kgs/M3) of plank size 1200 mm X 120 mm (minimum) having Lock & Fold locking arrangement and Aqua Seal edges for better spill resistance. Surface finish will be Embossed in Register (EIR) or Hand Sculpted (HS). Underlayment for laminate flooring made of natural color foam 2mm thick including end profile, transition profile, reducer, stair nosing and T profile complete all as specified. Make : Asian flooring India Pvt Ltd / Green Panel / Lamiwood.

M&L for Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S& F in repairs for 6mm plywood grade BWP, type BB, fixed with screws to timber frame work all as specified and directed

S&F in repairs for 18mm particle board medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timberframework all as specified and directed.

Supply and fixing in repairs breathe class 'A' acoustic fabric for walls, acuastically transparent fabric, designed to abrorb mild to high frequency sound, manufactured from 100% polyester, having minimum weight of 500 gm/m (+/-5%), 80,000 cycles abrasion resistance, colour fastness wet : 4 and dry : 5, flamability ASTM E-84 class 1 or A fixed with SR adhesive, approved for use in Dolby atmos studios, auditorium and cinema halls all as specified and directed by Engineer-in-charge. Make : MMT Acoustix / Welspun / D Decor / Reliance Textiles / AYM Syntex

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including ridges as in roof covering at a height of approx 20 m all as specified & directed.

S&F pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of colour as approved by GE and having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws at a height of approx 10 m all as specified.

S&F pre- painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ridge/cladding to wall, fixed with self tapping screws at a height of 10m all as specified

Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles. Note :This work has to be performed upto a height of 15 m

M&L for brick work with sub class 'B' bricks old size bricks, straight or curved on plan to any radius, built in cement mortor (1:4) complete all as specified and directed. Note :This work has to be performed upto a height of 15 m.

M&L for preparation of new plastered surface of wall and applying two coats of cement base paint complete all as specified and directed.

M&L for Cement concrete (1:3:6) type C-1 using 20mm graded stone aggregate as in copings of roof parapits complete all as directed. Note :This work has to be performed upto a height of 15 m.

S&F mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, cooler stand 12mm sq guard bar, framework of water tanks and similar works of quality Fe 290 (Gde E-165) etc complete all as specified and directed by Engineer-in-charge.

S&F rolled mild steel as in Joist, channel, angle or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length directed) and similar work conforming to Gde E-250 (Fe 410-W) quality `A’ all as specified and as directed.

M&L for providing and fixing with MS surface by duly welding MS wire mesh wt not exc 4 Kg /sqm before fixing, surface should be cleaned and should be free from dirt, oil grease etc complete all as specified and directed

M&L for 75 mm thick PCC (1:3:6) type C-2 using 40 mm graded crushed stone aggregate as in plinth protection, finished fair and even complete all as specified and directed by Engineer-in-charge. Note :- Plinth protection shall be laid to slope (1 in 30) in bays not exceeding 3 metre in length and joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with sealing compound grade B. Cost of ceiling compund is included in the unit rate of this item.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

S&F mineral fiber XL 1/4" reveal accoustical suspended ceiling system with silhouette exposed grid. The tiles should have humidity resistance (RH) of 99%, minimum NRC 0.7%. Light reflectance shall be more than 85% thermal conductivity K=0.052-0.057 w/mk. colour shall be white, fire perfomance class 0/class 1 (BS 4760 in module size of 600mmx600mmx15mm with bioblock coating on the face of tiles. The tiles shall be laid on silhouette profile grid system with 15mm with flanges incorporating 6mm central reveal in white/black colour and with a web height of 45mm and and load carrying capacity of minimum 15.68kg/sqm. silhouette, main runner (144" x 9/16" x 1-3/4") and cross runner (96" x 9/16" x 1-3/4"), face dimension 9/16" 15mm shall have mitred end and birdsmouth notches to provides mitred juction.Tee section shall have a galvanising of 125gms/sqm complete all as specified and directed. Note: This work has to be performed upto a height of 15 m. Make for Mineral Fibre Board and Silhouette exposed grid : Arm Strong / Hunter Dougles / Gyproc

M&L for false ceiling with 10mm thick plaster of paris sheets fixed with machine screws with and including GI channel 18 guage thick grid work, main joist placed at 750 mm centre to centre hanging with 6 mm dia GI wire suspenders from roof, J hook bolts and nuts etc and treating the POP sheets with thin layer of POP with gypsum anhydrous binder and prepare the surface till smooth surface is achieved and applying two coats of plastic emulsion paint complete all as per manufacturer's instructions complete all as specified and directed.

S&F GI lay in metal ceiling system of 600 x 600mm module which includes provides and fixing 'C' wall angle of size 20 x 30 x 20 mm of 0.5 mm thick prepainted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm c/c , suspending the main main C carrier os size 10 x 38 x 10 mm made of GI steel 0.7mm thick from the soffit with help of soffit cleat 37 x 27 x 25 x 1.6mm, rawl plugs of size 38 x 12 mm and C carrier suspension clip and main carrier bracket at 1000mm c/c. Inverted triangle shaped spring Tee having height of 24mm and width of 34 mm made of GI steel 0.45mm thick is then fixed to main C carrier and in direction to perpendicular to it at 600mm c/c with help of suspension brackets. Where ever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120gm/sqm(both side inclusive, fixing with clip in tiles into spring T with and including providing following type (Item No 95.00 & 96.00) ceiling board :-

GI metal ceiling lay in plain beveled edge global white colour tiles of size 600 x 600mm and 0.5mm thick with 25mm height, made of GI sheet having galvanizing of 100gm/sqm (Both side inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending complete all as specified and directed

GI metal ceiling lay in plain beveled edge global white colour tiles of size 600 x 600mm and 0.5mm thick with 25mm height, made of GI sheet having galvanizing of 100gm/sqm (Both side inclusive) and 20% perforation area with 1.8mm dia holes and having NRC of 0.5 electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation.complete all as specified and directed.

S&F hollow corrugated shape PVC wall lining consisting of 5mm thick decorative colour PVC sheet inclusive of solvent cement and fixing and incl beading at sides on PVC frame as per specifications all as specifed complete all as specified and directed.

S&F Collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete all as specified and directed.

S&F plain 1.25 mm thick GI sheet for covering crumple joints comple all as specified and directed.

S&F in reapirs stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.

S&F in repair sensored pillar tap 15mm bore cast copper alloy with capstan heads, chromium plated screwed down high pressure fancy type long screwed shank and fly nuts for iron pipe complete all as specified and directed. Make : Cat Part No F6010101 of Cera or equivalent in approved makes as specified.

S&F in repairs sensored half stall urinal of size 320mm x 300mm x 525mm complete all as specified. Make : Cat Part No S4010102 of Cera or equivalent in approved makes as specified.

S&F in repair vitreous china wash down, water closet pan floor mounted, cascade type of size 645mm x 345mm x 680mm, white combined with flushing cistern including fixing bolts and connection including slum soft seat cover complete all as specified and directed. Make : Cat Part No S1013161 of Cera or equivalent in approved makes as specified.

S&F stainless steel pipe for railing incl cutting , drilling, welding and fixing in position as directed by Engr-in-charge complete all as specified and directed.

S&F 10mm thick toughened glass with SS fixing arrangements in SS pipe complete all as specified and directed.

S&F 12mm thick toughened glass door with film of size exceeding 1.5 Sqm but not exceeding 3.00 Sqm including steel connectors, top and bottom pivots, stoppers, other fixtures required and all type of locking arrangement & brass handles fancy type 300mm long hole to hole on both side complete including taking down old unserviceable glass door complete all as specified and directed. Note:- Old glass door / partitions be removed and making good jambs, cills with the similar adjacent materials.

M&L for 100 mm outet diameter cast iron nahani trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

Dismantling loose/disintegrated portion of RCC Chajjas, bands, shelves, beams, coloumn or slab and similar work including support if required and stitching of cracks with MS U clamps of 8mm dia @ 150mm c/c with inserting concrate block strecthner with cement mortar (1:3) mixed with adhesive chemical (polymer based) and reinforced with PVC chicken mash formwork including where ever required and finished with 10mm thick plastering in CM (1:4) finished even & smooth without using extra cement including preparation of surfaces to receive finishes complete all as specified and directed.

M&L for water proofing treatment with APP modified bituminous membrane 3mm thick consisting of the following for RCC roof:- (a) Cleaning plastered roof surfaces and applying a coat of Oxidised bitumen based solvented primer @0.3 Kg/Sqm of approved make on top of dry surface of RCC roof complete all as specified and directed. (b) M&L for APP modified polymeric waterproofing membrane 3mm thick with non woven polyster core of approved make applied by heating one surface of membrane with LPG torch with lap of 100mm and the overlap shall be seated by flame complete all as per manufacture instructions and as directed.

M &L Cement concrete tiles 25cm x 25cm x 20mm thick, machine pressed; set jointed and pointed in neat cement slurry in floors/roof, and cut and polished incl 20 mm screed bedding layer in CM 1:4 complete all as specified & directed.

M&L for coloured vitrified paving tiles (any colour) of size 30cm x 30cm x 10mm thick, with gray cement & pigment set, jointed and pointed in neat cement slurry in floors laid over and including 15mm screed bedding in cement mortar (1:4) complete all as specified and directed.

Taking down surface / concealed copper / aluminium point wiring (light, bell, fan, socket or power) complete, including fixtures and fittings such as switches, ceiling roses, lamp holders, pendants, sockets, regulators, tubelight fittings, bulb, etc and making good disturbed surfaces with plaster on walls, floors etc complete all as specified and directed.

M&L for Point wiring complete with 2.5 sqmm single core FRLSH PVC insulated cable with multi stranded copper condutor in and including PVC conduit 20mm dia and thickness not less than 1.5mm, ISI marked with all accessories for surface or concealed conduit as directed at site incl chase cutting for one light/fan point controlled by one one way switch including MS sheet sunken box concealed on wall duly painted inside and outside with one coat of red oxide primer and two coats of black bituminous paint with 3mm thick hylum brand bakelite sheet cover for fixing switches, sockets, regulators etc. alongwith 2.5 sqmm multi stranded FRLSH, PVC insulaedcopper cable as continuous earth connected to common earth and earth dolly including making good the disturbed surfaces complete all as specified and as directed.

M&L for Point wiring complete with 4 sqmm single core FRLSH PVC insulated cable with multi stranded copper condutor in and including PVC conduit 20mm dia and thickness not less than 1.5mm, ISI marked with all accessories for surface or concealed conduit as directed at site incl chase cutting for one light/fan point controlled by one one way switch including MS sheet sunken box concealed on wall duly painted inside and outside with one coat of red oxide primer and two coats of black bituminous paint with 3mm thick hylum brand bakelite sheet cover for fixing switches, sockets, regulators etc. alongwith 4 sqmm multi stranded FRLSH, PVC insulaedcopper cable as continuous earth connected to common earth and earth dolly including making good the disturbed surfaces complete all as specified and as directed.

All as per Sl item No 113.00 above herein before but one socket out let 5 pins 5 Amp on the independent board complete all as specified and directed.

All as per Sl item No 113.00 above herein before but one socket out let 5 pins 5 Amp on the same board but with other switches complete all as specified and directed.

S & F modular type 6A one way SP switch 1 module confirming to IS: 3854-1997 with finger proof terminal complete all as specified and directed.

S & F modular type 2/3 pin 6 Amps socket 2 module conforming to IS: 1293-2005 complete all as specified and directed.

S & F modular type 16 A one way SP switch 1 module confirming to IS: 3854-1997 with fingure proof terminal complete all as specified and directed.

S & F modular type 2/3 pin 16 Amps socket 2 module conforming to IS: 1293-2005 complete all as specified and directed.

S&F in repair Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB complete all as specified and directed.

S & F modular type 120W step fan regulator of 2 module size conformng to IS: 11037-1984 complete all as specified and directed.

S & F Modular Blank plate 1 module suitable for Modular switch boards all as specified and as directed.

S & F Modular cover plate 8 modules complete all as specified and directed.

S & F Modular cover plate 4 modules complete all as specified and directed.

S & F Modular cover plate 3 modules complete all as specified and directed.

S & F Metal flush box 3 module complete all as specified and directed.

S & F Metal flush box 4 module complete all as specified and directed.

S & F Metal flush box 8 module complete all as specified and directed.

S & F ceiling rose three terminal, 230 Volts PVC / Polycarbonate body, complete all as specified and directed.

S & F LED (1.2 M) smartbrite extra batten made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having a nominal system lumen output of 2000 lumen/20 watt at a minimum system efficacy of 2000 lumen per 20 watt and total power consumption not more than 20 watt including driver of capacity 10 KA. it has a rated system life time of 25000 burning hours at L70 and should have a colour temperature of 6500 K, CRI>80, THD<10% AND PF>0.95 complete all as specified and directed.

S & F of LED (0.6 M)/ 2 ft smartbrite extra batten made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having a nominal system lumen output of 1150 lumen/10 watt at a minimum system efficacy of 1150 lumen per 10 watt and total power consumption not more than 10 watt including driver of 5 KA capacity. it has a rated system life time of 25000 burning hours at L70 and should have a colour temperature of 6500 K, CRI>80, THD<10% AND PF>0.95 complete all as specified and directed.

S&F in repair Security Light of 35 watts of new generation energy saving & environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having IP65 protection and impact resistance of IK07 with 10KV Built -in-Surge Protection Devision,should have a colour temperature of 6500 K, CRI>80, THD<10% AND PF>0.95 including suitable pipe, clamps, nut and bolts for mounting the light all as specified and directed

Supply and fixing in repair round shape 15 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete.( Note ligts need to be installed at the height of 11 mtr all necessary T & P required should be arranged by the contractor without any extra cost)

Supply and fixing in repair LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete.

S & F in repair LED step light, 2 watt, step glow surface mounted anthracite stair light,warm white complete all as specified and directed.

S & F in repair LED flood light ,150 watt, natural white,IP66 4kV,18000 limen,color temp 5700K and housing material aluminiun complete all as specified and directed.

S & F in repair ENTECH signs & Displays EXIT Red colour Safety sign 5 inch height contour light box complete all as specified and directed.

S & F in repair picture light for display warm white ,7 watt complete all as specified and directed.

S & F in repair Step light down step light alluminium Profile for strips width 64mm,height 29mm,diffuser material PC , diffuser finish frosted with end caps and mounting clips complete all as specified and directed.

M&L for sub main wiring with two single core 2.5 Sqmm PVC insulated FRLS multistranded flexible copper conductor cable 660/1100 volts grade down in through non metalic PVC casing caping with and including PVC insulated 2.5 Sqmm single core single strand copper conductor as continous earth wire in green colour connected to common earth dolly including taking down old unserviceable submain wiring complete all as specified and as directed Note : 1. Two runs of cable, one run of earth wire, one run of PVC casing capping will be measured and paid one unit.

M&L for sub main wiring with two single core 4.0 Sqmm PVC insulated FRLS multistranded flexible copper conductor cable 660/1100 volts grade down in through non metalic PVC casing caping with and including PVC insulated 4.0 Sqmm single core single strand copper conductor as continous earth wire in green colour connected to common earth dolly including taking down old unserviceable submain wiring complete all as specified and as directed Note : 1. Two runs of cable, one run of earth wire, one run of PVC casing capping will be measured and paid one unit.

M&L for sub main wiring with two single core 10 Sqmm PVC insulated FRLS multistranded flexible copper conductor cable 660/1100 volts grade down in through non metalic PVC casing caping with and including PVC insulated 410 Sqmm single core single strand copper conductor as continous earth wire in green colour connected to common earth dolly including taking down old unserviceable submain wiring complete all as specified and as directed Note : 1. Two runs of cable, one run of earth wire, one run of PVC casing capping will be measured and paid one unit.

M&L for concealed submain wiring with PVC insulated FRLS-H multistranded copper conductor cable of size 16 Sqmm drawing into and including rigid non metallic PVC conduit, medium grade not less than 25 mm dia ISI marked ivory colour with all conduit fittings and fixing accessories and 16 Sqmm FRLS-H multistranded copper conductor cable as continuous earth wire including cutting chasing ,making existing colour on the wall and taking down unserviceable submain complete all as specified and directed. (Note :- two runs of 16 Sqmm copper wire and one run of 16 sqmm copper earth wire alongwith PVC conduit shall be meausred as one unit)

S&F in repair DB TPN factory made distribution boards double door, protection class IP-42 suitable for mounting MCB's , DBs conforming to IS-13032, IS-8623, BS-5484 with min 200 Amps rating copper bus bar, 12 Ways, 415 V complete all as specified and directed.

S&F in repair DB factory made distribution boards double door, protection class IP-42 suitable for mounting MCB's , DBs conforming to IS-13032, IS-8623, BS-5484 with min 200 Amps rating copper bus bar, 08 Ways, 240 V complete all as specified and directed.

S&F in repair DB factory made distribution boards double door, protection class IP-42 suitable for mounting MCB's , DBs conforming to IS-13032, IS-8623, BS-5484 with min 200 Amps rating copper bus bar, 04 Ways, 240 V complete all as specified and directed.

Supply and fixing in repair TPN (triple pole & neutral) 40-100 A , 415V 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the DB complete with connection testing and commissioning all as specified and directed.

Supply and fixing in repair MCB SPN (single pole & neutral) 32 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

S & F MCBs of 'C' series SP (single pole) 6 to 32 amps having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs complete all as specified and directed.

Supply and fixing in repalcement exhaust fans 450 mm sweep metallic body, heavy duty, four blade, double ball bearing, 1400 RPM, minimum air delivery discharge 1710 CMH suitable for SP, 230/250V, 50 Hz AC supply with protective bird guard with louver shutters including grouting of frame in wall and connecting with and including 3 run 1.5 Sq mm single core, PVC insulated but unsheathered FRLSH multistranded copper conductors cable from ceiling rose to exhaust fan complete all as specified and directed. Note : Old exhaust fan deposit to MES store yard.

M & L in replacement of Earthing complete with galvanized steel earth plate electrode 60cmx60cmx 6.3mm thick buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 meter below normal ground level, connected to galvanised earth lead wire 4.0 mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in elecrical plate No 3 of MES SSR Part I connected to main DB or main control board all as specified and testing on completion including provision of earth wire portected by galvanised iron 40 mm bore light grade pipe with all fittings from the earth electrode fixed along pole with and including 25 x 6 mm flat iron clamp, bolts, nuts and washers and watering pipe shall be 20 mm bore GI medium grade from Top of the earth electrode to bottom of the earth pit and earth electrode shall be surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides including all excavation and earth work in any type of soil and removal of soil upto 50 metre, PCC pit with pre-cast RCC cover with handle with 10mm dia, charcoal/salt, funnel, CI frame etc complete all as specified and directed.

M & L for taking down split AC of any capacity by disconnecting all electric connection and refrigerant connection pipe and keeping in safe custody and refixing the same complete all as specified and directed.

M&L for servicing of split type AC of capacity 1.5 / 2 TR of any type or make by opening the condenser unit fixed on roof top and cooling unit fixed inside the building, and cleaning the complete condenser unit and cooling unit including fins and checking / testing of all parts for its serviceability, and oiling / greasing of motors, replacing worn-out bushes of blower, rectification of unusual noise, checking of refrigerant standing pressure, topping of refrigerant gas upto the required level, replacement of minor parts such as nut / bolt washers etc. and reassembling of complete unit including testing for smooth functioning complete all as specified and directed.

S & F in repair suction and discharge copper tube of existing size with insulation and 3 core copper wire 2.5 sqmm complete all as specified and directed. Note : Suction, discharge, insulation and copper wire all are measured as one unit.

Taking down ceiling fan / wall fan of any capacity by disconnecting all electric connection and keeping in safe custody and refixing the same complete all as specified and directed.

M/S MAMTA CONSTRUCTIONS (BID ID -3124355)

M/S SHRI RAM INFRASTRUCTURE (BID ID -3125693)

Ms Kamal Kant Agarwal (BID ID -3125521)

ms Jyoti traders (BID ID -3125443)

shyam construction (BID ID -3125546)