CA NO. CWE SGNR - 78 OF 2020-21 SPECIAL REPAIRS TO SINGLE OFFICERS ACCOMMODATION BUILDING NO. P-08 AT MILITARY STATION LALGARH JATTAN

Amount

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Demolition of reinforced cement concrete of any description and in any position not otherwise specificlly provided for (reinforcment cut as required to faciliate demolition) complete all as specified and directed by Engineer-in-Charge.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc. complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster on brick / stone walls including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed by Engineer-in-Charge.

M&L for brickwork with fly ash bricks, straight or curved exc. 6 m mean radius built in cm 1:6 complete all as specified and directed by Engineer-in-Charge.

M&L for Vitrified Ceramic tiles 10 mm thick (square/ rectangular) light shed polished, area of each tiles exceeding 0.36 sqm,but not exceeding 0.42 sqm in floors etc. over and including 15 mm thick screed bedding in cement mortar 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match the floor complete all as specified and directed by Engineer-in-Charge.

M&L for Vitrified Ceramic tiles 10 mm thick (square/ rectangular) light shed polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm,on vertical surfaces such as skirting / dados over and including 10 mm thick backing coat in cement mortar 1:4, set and jointed in neat cement slurry and pointed in white or coloured cement to match the floor complete all as specified and directed by Engineer-in-Charge.

M&L for joint free non skid ceramic coloured tiles 7 to 8 mm thick (square/ rectengular) area of each tile exc 0.06 Sqm but not exc 0.11 Sqm in floor over and including 15 mm thick screed bedding in cement mortar 1:6, set and jointed in neat cement slurry and pointed in coloured cement to match the floor complete all as specified and directed by Engineer-in-Charge.

M&L for glazed ceramic coloured tiles of size 350 X 250 X 7 mm / 450 x 350 x 7 mm thick on vertical surfaces such as skirting / dados over and including 10 mm thick backing coat in cement mortar 1:4, set and jointed in neat cement slurry and pointed in coloured cement to match the floor complete all as specified and directed by Engineer-in-Charge.

M&L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed by Engineer-in-Charge.

M&L for machine cut Kota stone slab flooring 20-25 mm thick (minimum size 55cm x 55cm) laid over and including 15 mm thick screed base in cement mortar (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and mirror polishing complete all as specified and directed by Engineer-in-Charge.

M&L for machine cut kota stone slab 20-25 mm thick in riser of steps, skirting, dado and pillar laid over and including 10 mm thick backing coat in cement mortar 1:4 set and jointed in neat cement slurry mixed with pigment to match shade of the slab including rubbing and plishing complete all as specified and directed by Engineer-in-Charge.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed by Engineer-in-Charge.

Formwork to chajjas, troughs and similar items including edges , for rough surface of concrete, complete all as specified and directed by Engineer-in-Charge.

M&L for reinforced cement concrete 1:1.5:3 type A-1 using 20mm graded stone aggregrate in Chajjas; complete all as specified and directed by Engineer-in-Charge. Note : Reinforcement shall be measured and paid seperately.

S&F mild steel TMT bars 10mm dia and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clip complete all as specified and directed by Engineer-in-Charge.

M&L for rendering, 15 mm thick on brick work or concrete surfaces in cement mortar 1:6 on wall finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for rendering, 15 mm thick on brick work or concrete surfaces in cement mortar 1:4 on wall finished even and fair complete all as specified and directed by Engineer-in-Charge.

M&L for two coats of oil bound distemper on newly plastered surfaces of walls paint over 3mm thick wall care putty including preparation of surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for complete removal of existing treatment and two coats of oil bound distemper over 3 mm thick wall care putty on plastered surfaces of walls including preparation of surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for 3 coats of white wash on newly / old plastered surfaces incl preparation etc. complete on wall complete all as specified and directed by Engineer-in-Charge.

M&L for two coats of cement base paint on newly / old plastered surfaces incl preparation etc. complete on wall complete all as specified and directed by Engineer-in-Charge.

Dismantling of brick tiles in floor laid dry and pointed in cement mortar complete all as specified and directed by Engineer-in-Charge.

Demolition mud in roofs, any thickness, including plastering and leeping complete all as specified and directed by Engineer-in-Charge.

M&L PCC (1:7:12) using 40mm graded stone aggregate as filling of sunken floors/bottom and side of drain complete all as specified and directed by Engineer-in-Charge.

M & L Lime concrete terracing as specified in roof (excluding bitumen tack coat) complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 15mm thick on brickwork or concrete surfaces in cement mortar 1:4 and finished fair and even including mixing of WPC in mortar complete all as specified and directed by Engineer-in-Charge.

Supply only integrated water proofing compound complete all as specified and directed by Engineer-in-Charge. Make:- Dr Fixit/Fosroc/BASF/STP

M&L For roof treatment to RCC Roof as follows:- (a) Cleaning the roof surfaces throughly using wire brushes to ramove sharp projections,cleaning joints,washing,drying and removing all dirt/dust to receive concrete padding plaster etc. (b) Providing 15mm thick screed bed or bedding layer of cement mortar (1:4) with WPC, finished even and smooth without using extra cement. (c) Provide one coat of approved bituminus primer @ 100 gms per sqm over dried plastered surface. (d) Laying 3mm thick APP membrane (mineral finish) reinforced with non woven polyster fabric by torch application. the overlapping while torching shall be 75mm on longitudnal direction and 100mm on the transverse direction complete all as specified and directed by Engineer-in-Charge. Make:- STP, Dr fixit/pidilite,Texca india ltd/Tikitar Dansona /Bengal Bitumen Notes:-(I)all joints and change in direction should be covered with cement mortar (1:3) mixed with SBR latex @ 200ml/bag of cement as per site requirment and cured well before laying membrane by torching. (II) All angles and abuttments should be sealed well with extra care to ensure full bondage. (iii) Water proofing treatment shall be got carried out by approved authorised applicator of manufacturer only. the name of firm shall be got approved from GE before carring out the work . (iv) The independent testing of membrane for technical parameters given in perticular specifications shall be carried out from Govt approved labs having facilities for testing of membrane. (v) The guarantee of treatment shall be for minimum 10 yrs reckoned from date of complition of whole work.

M&L PCC 1:2:4 type B-1, using 20mm graded stone aggregate as in roof kerbs or mud stops, rounded or chamfered on edges including necessary form work etc complete all as specified and directed by Engineer-in-Charge.

S&F Framed work such as grills,gratings,etc. With ends of bar shouldered or riveted or forged into spikes framed guard bars barred iron doors ladders framed balusters walk ways railings frame work of watertanks and similar works conforming to fe. 290 Gde-E-165 complete all as specified and directed by Engineer-in-Charge.

M&L for Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frames n.exc 1.5 sq. m each with shutters (without taking off shutters from the frame) complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frames exc 1.5 sq. m but n.exc 4.0 sq. m each with shutters (without taking off shutters from the frame) complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of any description exc 1 Sqm and n.exc 2 Sqm each complete all as specified and directed by Engineer-in-Charge.

S&F framed work as in chowkats of doors windows of angle iron ,gates or other section with gusset plates, rails, braces etc conforming to Gde Fe 410-0 complete all as specified and directed by Engineer-in-Charge.

S&F hold fast of flat iron 25 x 3 mm conforming to Fe-290 or Fe 330 including preparing the surfaces & treated with two coats for coaltar & sanded with clean sharp sand complete all as specified and directed by Engineer-in-Charge.

S&F powder coated aluminium frame/shutter for doors, windows, ventilators and aluminium partition with one or more rebates including jointing cleats glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete with locking arrangements for fixing with powder coating on aluminium sections, minimum thickness of poweder coating shall be 50 micron as per the specification. The top and bottom horizontal members and vertical members adjacent to wall shall be fixed with floor, ceiling, walls and cills where required and fixed with the help of rawl plugs and screws or with fixing clips or with expansion hold plate fastners. Aluminium section shall be smooth, rust free, straight, mitred and jointed mechanically whereever required complete in all respect complete all as specified and directed by Engineer-in-Charge.

S&F powder coated anodised aluminium fully glazed window & ventilator door shutters side hung type, aluminium section weighing exc. 0.55 kg/ m (1.50 to1.80mm th) including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminum snap beading screws etc. long handles 2 Nos, hinges type B-21 100 mm long (4 Nos), aluminium door stopper, PVC door chock in each door shutter and necessary accessories as required complete all as specified and directed by Engineer-in-Charge. Note : Glass/grill will measured and paid separately

M&L 4.8 mm thick sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 Sq. m in each pane with solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specified and directed by Engineer-in-Charge.

M&L for Cement concrete 1:3:6 type C–1 (using 20mm graded crushed stone aggregate) as in coping, hold fast, bed blocks or similar block etc complete all as specified and directed by Engineer - in - Charge.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed by Engineer-in-Charge.

S&F factory made solid PVC door shutter 30 mm thick (style) consisting of frame made out of mild steel tubes for top and bottom rails frame shall be covered with heat moulded both side Prelam PVC `C' channel having a PVC sheet strip of 20 mm width stuck and both side Prelam PVC sheets for top rail and bottom rail, panelling of both side Prelam PVC sheet to be fitted in the mild steel frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement, supplying and fixing in the frame complete all as specified and directed by Engineer-in-Charge.

S&F 100 mm long butt hinge, extruded aluminium alloy with galvanised mild steel hinge pin, anosied and fixed type B-21 complete all as specified and directed by Engineer-in-Charge.

S&F 200 mm long aluminium anodised barrel tower bolt, of extruded sections complete all as specified and directed by Engineer-in-Charge.

S&F 150 mm long aluminium anodised handle, cast type complete all as specified and directed by Engineer-in-Charge.

Taking down existing shutter and refixing in same opening shutters of any description exc 1.0 Sqm but not exc 2.0 Sqm each complete all as specified and directed by Engineer-in-Charge. Note:- 'Refixing' includes taking down, easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc.

S&F 35 mm thick 2nd class hard wood factory made plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed by Engineer-in-Charge.

S&F 35 mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) complete all as specified and directed by Engineer-in-Charge.

S&F flush shutter 25mm thick solid core construction with block board core and plywood face panels; commercial type on both sides as cupboard and kitchen shutters complete all as specified and directed by Engineer-in-Charge.

S&F 100 mm long butt hinge, medium weight, cold rolled mild steel complete all as specified and directed by Engineer-in-Charge.

S&F 300 mm long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed by Engineer-in-Charge.

S&F for 300mm long aluminium alloy, anodised, sliding door bolt type not less than 16mm dia fixed complete all as specified and directed by Engineer-in-Charge.

S&F as 300mm ordinary rat tail rod pattern springs including roller and roller plate complete mild steel fixed complete all as specified and directed by Engineer-in-Charge.

M&L Block board, 19/20mm thick, grade 1 quality, exterior grade, decorative type with decorative face veneer on both face, fixed with screws to timber frame work complete all as specified and directed by Engineer-in-Charge.

M&L plain fillets, square, rectangular or triangular in section, wrought, secured with nails or brads, sectional area exc 3 & n.exc 6 Sq.cm of 2nd class hard wood complete all as specified and directed by Engineer-in-Charge.

S&F continous (piano) hinges, mild steel, bright finish or electrogalvanised (width of flaps 30mm ) complete all as specified and directed by Engineer-in-Charge.

S&F 125mm hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed by Engineer-in-Charge.

S&F 125 mm long aluminium anodised handle, cast type complete all as specified and directed by Engineer-in-Charge.

S&F Stainless steel wire cltoth 0.63mm nominal dia of wire and average width of of aperture 1.40mm and fixed with stain less steel wire staples complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 61 here-in-above but for fixing in repairs complete all as specified and directed by Engineer-in-Charge.

M&L 12 mm thick Pre-laminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed by Engineer-in-Charge.

S&F 150 mm long floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring complete all as specified and directed by Engineer-in-Charge.

M&L preparation of new or previously untreated wooden surface of any description not otherwise described over 10 cm width or girth and apply two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed by Engineer-in-Charge.

S&F drapery rods, coloured, standrad quality, powder coated not less than 25mm dia with heads at both ends and middle support, rings, etc. complete all as specified and directed by Engineer-in-Charge.

S&F in repair corner glass shelf 200mm with Abs brackets complete all as specified and directed by Engineer-in-Charge.

S&F in repair brass hat pegs, solid body, 125 mm to 175 mm (4 legs) complete all as specified and directed by Engineer-in-Charge.

S&F in repair towel rails 20mm dia 600mm long brass chromium plated superior quality brass chromium plated fancy type complete all as specified and directed by Engineer-in-Charge.

S&F in repair stainless steel grating round or square 150mm size (minimum weight 100gms) complete all as specified and directed by Engineer-in-Charge. Note :- The minimum weight shall be as given in SSR or in relevant IS.

S&F in repair chromium plated fancy type soap dish complete all as specified and directed by Engineer-in-Charge.

S&F vitreous china wash down water closet pan (pedestral pattern), white (excluding fixing bolts ,flushing cistern and flush pipe), including pedestral pan and trap,including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc complete all as specified and directed by Engineer-in-Charge.

S&F In repair plastic water closet seat, white closed pattern with flat bottom,and cover and mild steel chromium plated or aluminised hanging device seat and cover for water closet (European type) complete all as specified and directed by Engineer-in-Charge.

S&F in repair stainless steel chromium plated jet spray (butter fly or ''L'' bend) suitable for EWC includimg 1m tube and necessary nut bolts complete all as specified and directed by Engineer-in-Charge.

S&F in repairs PVC valve less, syphonic action type flushing cistern,10 ltrs capacity low level, white, with inlet ball valve, float, handle and telescopic pipe and connection to pipe and flush pipe of polyethylene of low or high density or PVC, 32mm dia, for low level cistern complete all as specified and directed by Engineer-in-Charge.

S&F in repair vitreous china wash hand basin coloured Flat back of size 550x400mm, long screwed shank fly nut flange end including cutting for and pinning in ends of brackets in 1:3 CM including 32mm dia chromium plated waste coupling / trap complete all as specified and directed by Engineer-in-Charge.

S&F pillar tap, fancy type, cast copper alloy chromium plated with capston head, screwed down high pressure with or without lettered with long screwed shank and fly nuts, screwed for iron pipe of 15 mm bore complete all as specified and directed by Engineer-in-Charge. Note : Weight not less than 450 gms

S&F in repair bib tap, fancy type, cast copper alloy, chromium plated, with crutch or butterfly handles, screwed down, screwed for iron pipe or for brass ferrule & fixed suitable for 15mm bore iron pipe complete all as specified and directed by Engineer-in-Charge. Note :- The minimum weight of tap shall be as given in SSR or in relevant IS.

S&F in repair bib tap 2-Way double handle with flange, fancy type, cast copper alloy, chromium plated, with crutch or butterfly handles, screwed down, screwed for iron pipe or for brass ferrule & fixed suitable for 15mm bore iron pipe complete all as specified and directed by Engineer-in-Charge. Note :- The minimum weight of tap shall be as given in SSR or in relevant IS.

S&F in repair angle valve/stop cock/stop valve fancy type, cast copper alloy, chromium plated screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union, size 15mm bore complete all as specified and directed by Engineer-in-Charge. Note :- The minimum weight of tap shall be as given in SSR or in relevant IS.

S&F in repair 15mm Concealed stop cock fancy type, cast copper alloy, chromium plated screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union, size 15mm bore complete all as specified and directed by Engineer-in-Charge. Note :- The minimum weight of concealed stop valve shall be as given in SSR or in relevant IS.

S&F in repair brass chromium plated 4'' Multi flow round shape single flow ( ABS Body chrome plated with gray face plate ) with rubit cleaning system with 240mm arm & flange including fixing to 15mm bore pipe complete all as specified and directed by Engineer-in-Charge.

S&F in repair brass chromium plated Liquid soap dispenser including fixing to 15mm bore pipe complete all as specified and directed by Engineer-in-Charge.

S&F in repair chromium plated fancy type health faucet with 1mtr tube & hook complete all as specified and directed by Engineer-in-Charge.

S&F PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed by Engineer-in-Charge.

Dismentling of water tanks of capacity exc 500 and n.exc 1000 ltrs and removing from site complete all as specified and directed by Engineer-in-Charge.

S&F rotational moulded polythene water storage tank 500 ltr (ISI Marked, three layers) capacity vertical with closed top hoisted and fixed in position all as specified in SSR part-I. complete all as specified and directed by Engineer-in-Charge.

S&F in repair gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of 20mm bore fixed in repair complete all as specified and directed by Engineer-in-Charge.

S&F in repair ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed in 20mm dia bore pipe complete all as specified and directed by Engineer-in-Charge.

Taking down 15 mm dia steel GI tubing including all connected fittings of any dia and in any position including cleaning for re fixing the serviceable pipe complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 91 here-in-before but for 20mm dia pipe complete all as specified and directed by Engineer-in-Charge.

S&F 15 mm dia galvanised steel tubing medium grade including necessary fittings like sockets, tees, elbows, reducers, unions etc fixed to walls / ceiling complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 93 here-in-before but for 15mm dia pipe fixing only complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 93 here-in-before but for 20mm dia pipe complete all as specified and directed by Engineer-in-Charge.

Dismantling of cast iron pipes, jointed in cement mortar and tabing out of trenches if required upto 100mm dia complete all as specified and directed by Engineer-in-Charge.

Dismantling of cast iron pipes, jointed in cement mortar and tabing out of trenches if required 75mm dia complete all as specified and directed by Engineer-in-Charge.

Supply & fixing 100 mm bore cast iron sand cast soil, waste and vent pipe in any length with or without ears fixed to wall with cement joints complete all as specified and directed by Engineer-in-Charge.

Supply & fixing 75 mm bore cast iron sand cast soil, waste and vent pipe in any length with or without ears fixed to wall with cement joints complete all as specified and directed by Engineer-in-Charge.

Fixing only 100 mm bore cast iron sand cast soil, waste and vent pipe in any length with or without ears fixed to wall with cement joints complete all as specified and directed by Engineer-in-Charge.

Fixing only 75 mm bore cast iron sand cast soil, waste and vent pipe in any length with or without ears fixed to wall with cement joints complete all as specified and directed by Engineer-in-Charge.

M&L in repairs 75mm dia cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate complete all as specified and directed by Engineer-in-Charge.

S&F in repairs branch pieces single (equal or unequal) ordinary or inverted (spring or socket type) or with paralled branch 100mm dia but with oval access door complete all as specified and directed by Engineer-in-Charge.

S&F in repairs branch pieces single (equal or unequal) ordinary or inverted (spring or socket type) or with paralled branch 75mm dia but with oval access door complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 75mm cast iron sanitary connections-short connections pipe of length upto 300mm with socket fixed complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 100mm cast iron sanitary connections-short connections pipe of length upto 300mm with socket fixed complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 75mm bore cast iron bends (any radius) dimining pieces or tapers (larger bore measured) with oval access door fixed with cement joints complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 100mm bore cast iron bends (any radius) dimining pieces or tapers (larger bore measured) with oval access door fixed with cement joints complete all as specified and directed by Engineer-in-Charge.

Taking down eaves gutters and rainwater pipes (any size or pattern) including all fittings, heads, shoes, bends, swan-necks etc., including cleaning or refixing or removal to Store complete all as specified and directed by Engineer-in-Charge. Note : measured overalll as fixed along the cente line over fittings and accessories

S&F 110 mm dia PVC SWR pipe, single socketed in any length with rubber ring joints fixed with clamps to walls complete all as specified and directed by Engineer-in-Charge.

S&F 75 mm dia PVC SWR pipe, single socketed in any length with rubber ring joints fixed with clamps to walls complete all as specified and directed by Engineer-in-Charge.

S&F 110 mm bore PVC (SWR) branch piece double (single Y) equal or unequal complete all as specified and directed by Engineer-in-Charge.

S&F 110 mm dia PVC (SWR) bend any radius complete all as specified and directed by Engineer-in-Charge.

S&F 75 mm dia PVC (SWR) bend with access door any radius complete all as specified and directed by Engineer-in-Charge.

S&F PVC (SWR) floor trap, 75 mm dia with grating including jointing with solvent cement etc complete all as specified and directed by Engineer-in-Charge.

M&L PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 32 mm dia low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors complete all as specified and directed by Engineer-in-Charge.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated curved roofing steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including fixing of ridge complete all as specified and directed by Engineer-in-Charge.

S&F in repair sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed by Engineer-in-Charge.

Taking down carefully copper/aluminium point wiring (light, socket or power) complete (fittings such as switches, ceiling roses, pendants, regulatos, sockets etc to be measured separately), and making good disturbed surfaces of walls, floors etc to match with existing surfaces complete all as specified and directed by Engineer-in-Charge.

Taking down MCB with sheet metal enclosure, main switch, DB etc and making good disturbed surfaces to match with existing surfaces complete all as specified and directed by Engineer-in-Charge.

Taking down sub main wiring of any size/capacity and making good disturbed surfaces to match with the existing surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for concealed Point wiring with two single core PVC insulate, unsheathed multistranded copper conductor cable of size 1.5 sq.mm (FRLS) drawn in and including electrical grade PVC conduit 20 mm dia concealed on wall/ceiling/floor including PVC insulated unsheathed earth wire with multi stranded copper conductor of size 1.5 sq.mm(FRLS) including MS shunk sheet metal box with modular sheet top cover of required module for mounting switches, sockets etc for One Light point controlled by one, one way switch complete all as specified and directed by Engineer-in-Charge. Note - quoted rate shall include making good to the disturbed surfaces including plastering and painting to match with the existing colour.

All as per Srl item No. 123 here-in-before but for one ceiling/exhaust fan point controlled by one switch and regulator complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 123 here-in-before but for one 3 pin switch socket outlet, 5 Amp on the same board with other switches complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 123 here-in-before but for one 3 pin 5 amps switch socket outlet point on independent board complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 123 here-in-before but for one bell/buzzer point controlled by one bell push complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 123 here-in-before but for two way point controlled by two way switch complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 123 here-in-before but for wiring with 4 sq.mm multistranded cable and earth wire with copper conductor of size 4 sq.mm for 15 amps power point complete all as specified and directed by Engineer-in-Charge.

Supply and fix Modular piano switch flush button single pole one way 10 Amps complete all as specified and directed by Engineer-in-Charge.

S &F modular piano socket 2 in 1, 2/3 pin 6 amp flush type 240 volts AC complete all as specified and directed by Engineer-in-Charge.

Supply and fix modular piano socket 2 in 1, 3 pin 5 amp and 16 amp flush type 240 volts AC complete all as specified and directed by Engineer-in-Charge.

Supply and fix modular piano switch 15 amp flush type 240 volts AC complete all as specified and directed by Engineer-in-Charge.

S & F LED tube light fitting 1 x 18 W, AC 230 V integral sleek polycarbonate LED Channel with white acrylic cover incl making connection complete all as specified and directed by Engineer-in-Charge.

Supply and fix lamp holder insulated body with back plate for angle/batten fitting with LED of 09 watt complete all as specified and directed by Engineer-in-Charge.

Supply and fix ceiling rose surface bakelite two to three terminals/plate 5 amps complete all as specified and directed by Engineer-in-Charge.

Supply and fix sheet metal enclosure DB single pole and neutral for 240 volts 8 way with 200 Amps rated busbar flush/surface mounting double door including wooden board complete all as specified and directed by Engineer-in-Charge.

Supply and fix Vertical MCBDB distribution box 3 phase TPN 4 ways double door as MCCB 125 Amp 16 KA as incommer with bus bar rating 200 Amps vertical type dust and vermin proof complete all as specified and directed by Engineer-in-Charge.

Supply and fix MCB single pole 240 volt 5-32 amps 10 KA, complete all as specified and directed by Engineer-in-Charge.

Supply and fix MCB SPN 240 volt 40 amp 10KA complete all as specified and directed by Engineer-in-Charge.

Supply and fixing PVC Blanking Plates one way with internal lock complete all as specified and directed by Engineer-in-Charge.

Material & Labour for Sub Main Wiring with two run single core 10 Sqmm PVC insulated unsheathed (FRLS) cable with stranded copper conductor drawn in PVC conduit & accessories Suitable size with and including 10 Sqmm copper green colour earth wire complete all as specified and directed by Engineer-in-Charge. NOTE-two run of 10 sq.mm & One run of 10 sq.mm & One run of PVC conduit with accessories shall be measured as One length.

S&F sheat metal incl single pole and neutal with 02 Pin and earth plug and socket complete with 01 single pole 20 Amps 240volts, MCB complete incl necessary fixing arrangement and all incoming and outgoing electric connection complete all as specified and directed by Engineer-in-Charge.

Material & Labour for Sub Main Wiring with two run single core 4 Sqmm PVC insulated unsheathed (FRLS) cable with stranded copper conductor drawn in PVC conduit & accessories Suitable size with and including 4 Sqmm copper green colour earth wire complete all as specified and directed by Engineer-in-Charge. NOTE-two run of 4 sq.mm & One run of 4 sq.mm & One run of PVC conduit with accessories shall be measured as One length.

Earthing complete with galvanized steel earth plate electrode 600mm x 600mm x 6mm buried directly in ground vertically to a depth not less than 2.25 Mtr below normal ground level connected to GI strip 32mm x 6mm dia by means of bolts, nuts, check nuts and washers complete including earthing pit, chemical compound, earthing lead 32mm x 6mm dia upto 7.5 Mtr, 20mm dia medium grade GI watering pipe, GI protection pipe 40mm dia earth pit in PCC 1:2:4 type B-1 using 20mm graded stone aggregate RCC pit cover including earth work complete all as shown in electrical plate No. 5 of SSR-2009 (Part-I) complete all as specified and directed by Engineer-in-Charge. Note : The unit rate shall be include for excavation and earth work in any type of soil / strata, PCC 1:2:4, type B-1 for pit and RCC 1:2:4 type B-1 for cover with 8mm dia CTD bar @ 150mm centre to centre both way, funnel with watering pipe 20mm dia medium grade, 15mm dia light grade GI pipe upto 7.5 Mtr long, wire mesh complete all as specified and directed by Engineer-in-Charge.

Taking down ceiling fan,dismantling, repairing complete with changing of bearing & bushed, lubricating and repainting, fixing back in position and reconnecting with 1.5 Sqmm 3.0 core wire complete all as specified and directed by Engineer-in-Charge.

S & F LED building security light fitting 45 watt with epoxy powder coated sheet aluminium housing, with epoxy powder coated CRCA sheet steel grey tray, clear acrylic cover and accessories complete incl street light bracket made out of 25 mm dia GI medium grade pipe 0.6 mtr long complete with 2 sets of FI clamps made out of 30x5 MS flat & nuts, bolts & washer including painting to clamp with two coats of aluminium silver paint over a coat of primer after taking down old u/s one complete all as specified and directed by Engineer-in-Charge.

M&L for taking down geyser 25 ltr capacity single phase 240 volt 50 Hz and refixing the same incl all electrical connection and two Nos PVC pipe, heating element, Indicating lamp and thermostat ISI marked and paintingthe same complete all as specified and directed by Engineer-in-Charge.

Supply and fix single phase tamper proof energy meter 10-60 Amp single phase complete all as specified and directed by Engineer-in-Charge.

S&F for Modular fan step regulator 120 watt , 2 module complete all as specified and directed by Engineer-in-Charge.

M&L for repair to door hinges of MS housing of size 100x.90 m icluding necessary welding and painting the panel with two coat of synthaticenamelled paint over a coat ofred oxide primer complete all as specified and directed by Engineer-in-Charge.

Supply and fix fresh air fan 230 mm sweep 240 vot 50 Hz plastic body complete with louvers complete all as specified and directed by Engineer-in-Charge.

Supply and fix Exhaust fan metalic body 300 mm sweep 240 vot 50 Hz with louvers complete incl making hole, fastners etc. complete all as specified and directed by Engineer-in-Charge.

M&L for MS perforated cable tray 1.25 mm thick 100 mm width in length of 2.5 meter each connected with connector/tees etc with cover, to be fixed horizontally/ vertically complete including fixing accessories, fittings and fixtures complete all as specified and directed by Engineer-in-Charge.

M&L for cutting circular/rectangular holes in wall suitable for 300 mm sweep exhaust fan/Fresh air fan including smothening, plastering and making good disturbed surfaces with 1:3 cement mortarand, painting, complete with fixing of suitable wiremess for protection from birds complete all as specified and directed by Engineer-in-Charge.

Supply, laying and testing of Cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured, electric power cable with stranded aluminium conductor 1100 Volt grade of size 50 Sqmm 3.5 core complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches not exc 1.5 m wide and n. exc 1.5 m deep in soft/loose soil for foundation/ cable etc n exc 10 Sqm on plan and n exc 1.5 Sqm in depth complete all as specified and directed by Engineer-in-Charge.

Returning, filling in including spreading levelling, watering and well ramming in layer n. exc 25 cm thick complete all as specified and directed by Engineer-in-Charge.

Removing surplus soil to a distance n. exc 50 m and depositing where directed at level n. exc 1.5 m above the starting point complete all as specified and directed by Engineer-in-Charge.

M&L sand cushioning with dry coarse sand to under ground cable 230 mm deep (80 mm below and 150 mm above the cable) complete all as specified and directed by Engineer-in-Charge.

M&L brick protection with sub class'B' brick laid flat across the cable complete all as specified and directed by Engineer-in-Charge.

Supply and fix GI pipe light grade of size 50 mm bore in wall/pole complete all as specified and directed by Engineer-in-Charge. -------------------------------------------------------------------------- Note : A sum of Rs. 34,446.00 will be deducted on account of credit for dismantled/ demolished / taken down material. Please refer details on Srl Page No. 33 & 34 (Schedule of Credit) of Tender document

M/s Tarun Traders

Aggarwal brothers and company

ram rattan dass aggarwal

M/s AKG Engineers & Contractors