8260-SPECIAL REPAIRS TO ANIMAL STORE AND PROVISION OF AREA DRAINAGE, CAR PARKING AT OTA AND PROVN OFINTERLOCKING TILES AND CHEQUERED TILES AT QAE(N) AND NEAR TYPE-I AND II DGQA COMPLEX UNDER GE STM

Amount

Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings.

Suppl and fixing Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

Supply and fixing Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

Dismantling structural steel work including doors, gates but excluding framed truss etc.

S & F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.conforming to Fe 410-W (Gde-E- 250)quality-A

S&F mild steel work in tubular trusses, purlins, post, distance pieces including special shaped washer etc. complete using ERW or induction butt welded tubes confirming to IS 1161- 1979 grade St-240.

M&L Preparation of New or previously untreated steel surfaces and applying two coats of synthetic enamel paint over a coat of Redoxide primer.

M&L forRoughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc.

M&L for providing 50 mm thick PCC 1:2:4 type B1 using 20 mm graded stone aggregate as in floors and pavings etc.

Taking down chowkats or frames with shutters (without taking off shutters from frames) exc. 1.5 Sqm but n. exc 4 Sqm each including making good disturbed surfaces.

Taking down chowkats or frames with shutters (without taking off shutters from frames) n exc. 1.5 Sqm each including making good disturbed surfaces.

S&F Second class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints supplied and fixed.

S&F Second class hardwood 35 mm thick plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers; supplied and fitted to chowkats.

S&F MS flat iron as in hold fast, grills support to windows and similar small articles quality confirming to Fe-410-O or Fe- 310-O, complete all as specified and directed.

M & L for preparing surfaces of wood and wood based materials of any description and treated with tar or coal tar black paint treating ends of posts backs of chowkats etc area tarred exc 0.1 sqm but n exc 0.5 sq m each

M & L for preparing surfaces of wood and wood based materials of any description and treated with tar or coal tar black paint treating small articles such as stop covers gully gratings holdfasts ends of posts backs of chowkats etc area n exc 0.1 sqm each

S & F 100mm long butt hinges, medium weight, cold rolled mild steel, and fixed all as specified and as directed.

S&F Alumininum anodised barrel tower bolts of extruded section 200 mm size

S&F Extruded aluminium alloy handles, fabricated type, anodised 150 mm long

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded sections or cast aluminium alloy and fixed Length of bolt 300mm.

M & L for preparing surfaces of new wood or wood based surfaces any description not otherwise described over 10 cmm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets

S & F in true horizontel level modular false celling using hot dipped galvanised steel section. Exposed surface chemically cleaned capping prefinished in backed polyester paint 24 mm grids wall angle of size 3000mm x22 mm x22 mm used in the periphery of the celling fixed to the partition, RCC coloumn and wall using screws at 600 mm c/c. Main runner of size 24 mm x32mm x 3600mm suspended at 1200 c/c 4mm G I wire hanger safely fixed to the structural soffit of the RCC slab using 6mm anchor fastner at every 1200 mm c/c (max ) and 1200mm long cross tee of size 24mmx 23mm x1200mm to be interlocked between main runner at 600mm c/c (max) to form grid of 600mmx600mm. Tile to have PVC laminated in gypsum based tiles. (Make . Diamond )

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles

Material and Labour for Brickwork with fly ash modular bricks, straight or curved on plan exc 6m mean radius built in CM 1:6

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water etc

M&L Rendering 10mm thick on fair faces of brick work or concrete surfaces finished with even and smooth without using extra cement in CM 1:6

M&L Rendering 10mm thick on fair faces of brick work or concrete surfaces finished with even and smooth without using extra cement in CM 1:4

M&L Rendering 5mm thick on fair faces of brick work or concrete surfaces finished with even and smooth without using extra cement in CM 1:4

Supply only integral water proofing compound

M&L for complete removal of existing treatment and appling three coats of white wash

M&L for preparation of surfaces plastered or unplastered on new surfaces on walls and appling three coats of white wash

Demolition of cement concrete in ground floor & paving n.exc 15 cm thick below or above GL and removing the debris as directed

M & L PCC 1:3:6 type C1 using 20 mm graded stone aggregate, as in plinth protection 75 mm thick finished even and smooth without using extra cement including necessary form work all as specified

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out in hard/dense soil.

M&L for PCC 1:4:8, type D2 (using 40 mm graded agg) as in foundation, filling and mass concrete.

M&L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 all as specified.

M&L for PCC 1:2:4 type B-1 (using 20 mm graded agg) as in coping, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including form work all as directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends etc.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:4, finished even and smooth w/o using extra cement.

Removing excavated materials to a distance n exc 50m and depositing where directed at a level n exc 1.5m above the starting point.

M&L mild steel TMT bars 10mm dia and over, cut to length, bent to shape required incl cranking, bending spirally for hooping for columns, hooking ends and binding with and incl mild steel wire annealed, not less than 0.9mm dia or securing with clips.

M&L for precast cement concrete 1:2:4, type B1 using 20mm graded aggregate as in drain cover slabs with 40mm dia holes made in the cover slabs to drain run off set in cement mortar 1:6 complete all as specified.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25cm in hard/dense soil.

Surface excavation n. exc (not exceeding) 30 cm deep and averaging 15 cm deep and getting out hard/dense soil.

M&L for hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface of broken stone or boulders.

M&L for 100mm thick PCC 1:4:8, type D2 using 40 mm graded stone aggregate as in sub base of floors and pavings etc.

M&L for 100 mm thick PCC 1:2:4, type B1 using 20 mm graded stone aggregate as in flooring and paving etc.

M&L for sand filling under floors including spearding and levelling inlayers n exc. 25 cm thick, watering and consolidation.

M&L for machine pressed precast concrete interlocking paver block any shape and size conforming to IS 15658-2006 of 60 mm thickness, M-35 Grade of cement concrete with grey cement and pigment all as directed by Engr-in-Charge.

Excavating post holes (or similar holes) each n exc 0.5 cu m, getting out hard/ dense soil including removing surplus soil to a distance n exc 50m and making good surface.

M&L for PCC 1:2:4, type B2 using 40 mm graded stone aggregate as in foundation, filling and mass concrete.

M&L for Brickwork with fly ash old size bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 all as specified.

M&L for Brickwork with fly ash old size bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4 all as specified.

S&F mild steel work in tubular trusses, purlins, post, distance pieces including special shaped washer etc. complete using ERW or induction butt welded tubes confirming to IS 1161- 1979 grade St-240.

S&F S&F mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe 410-W (Gde- E- 250) quality-A

S&F Mild steel rag or lewis bolts, screwed one end, with hexagonal or square nuts and washers, the other end enlarged and jagged or lewised, exc 30 cm long of diameter of neck 20 mm .

M&L for preperation of new steel surfaces of any description, over 10 cm in width or girth and applying two coats of synthetic enamal paint over a coat of red oxide primer complete all as specified and as directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet bent to curve as required at site (of any radius) of 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall/valley gutter etc fixed with self tapping screws all as specified and directed.

S&F MS work for bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 all as directed.

S&F Mild steel flat iron for wind ties including drilling holes, securing bolt etc and similar work conforming to Fe-290 Gde-E 165.

S&F PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints fixed to walls, laid in trenches or in floors all as directed.

Preparing of new plaster surfaces and applying three coats of white wash on walls.

M&L for forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound Grade A.

Roughening surface of old concrete floor by picking sweeping clean and washing down with water to remove dust, etc

M&L coloured chequred cement concrete tiles 30cmX30cmX25mm thick (premium quality), set joined and pointed in neat cement slurry in floors with grey cement and pigment incl 15mm cement screed bed CM 1:4 complete all as specified and directed,

RMK INDUSTRIES

Sri Mahalakshmi Enterprises