GE U(N) 53 2022 23 REPAIR TO FLOORING PLASTERING INTERNAL WATER SUPPLY ETC OF TRANSIT CAMP HQ SUB AREA PROVOST UNIT R CENTRE UP AND DOWN CONVEY GROUND AND TA BN COY INCLUDING MD JCO ORS ACCN UNDER GE (N) UDHAMPUR

Amount

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc. ,complete all as specified and directed by the Engineer-in-Charge.

M&L for rendering 15 mm thick on fair faces of brick work in cement mortar 1:4 finished even and smooth without using extra cement and with using Water proofing compound .(Water proofing compound shall be measured and paid sepratly ) ,complete all as specified and directed by the Engineer-in-Charge.

M&L for rendering 10 mm thick in cement mortor 1:6 on fair face on brick/concrete surfaces and finished even and smooth without using extra cement ,complete all as specified and directed by the Engineer-in-Charge.

M&L for two coat of cement base paint over a coat of alkali resistant primer paint including preparation of newly plastered of wall ,complete all as specified and directed by the Engineer-in-Charge.

M&L for two coats of oil bound distember over a coat of primer over two coats of approved wall care putty 2 to 3mm thick over and including preparation of new plastered surfaces of wall ,complete all as specified and directed by the Engineer-in-Charge.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and recast concrete articles complete all as specified and directed by the Engineer-in-Charge.

M&L for brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM(1:6) with old size bricks complete all as specified and directed by the Engineer-in-Charge.

All as per item No. 07 above herein before, but except bricks. Note-Old bricks obtained against dismantling shall be used.

M&L for half brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM(1:6) with old size bricks complete all as specified and directed by the Engineer-in-Charge.

Disconnection of existing tanks, setting side for repairing, cleaning etc and hoisting after cleaning and removing all scale and dirt etc from tanks and from mouth of circulating pipe etc of capacity exc 500 to n.exc 1000 ltr and including endorsed the ward ' CLEANED ON WITH DATE' with white paint including replacement of broken/ unserviceable fitting such as elbow, Tea ,socket,nipple of any size etc,complete all as specified and directed by the Engineer-in-Charge.

M&L for hacking out old broken glass (any thickness, size, quality or description) from metal/ Aluminium frames including punching or drilling out old glazing pins/ spring clips ,complete all as specified and directed by the Engineer-in-Charge.

S&F in repairs 5.0 mm thick tinted sheet glass, ordinary quality and glazing with oil putty/ Aluminium rubber beading in squares exceeding 0.5 Sq.M in each pane ,complete all as specified and directed by the Engineer-in-Charge.

S&F in repairs 3 mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sq.M in each pane ,complete all as specified and directed by the Engineer-in-Charge.

Taking up/down steel tubing and connections including cleaning for refixing or removal to store 15mm bore pipes ,complete all as specified and directed by the Engineer-in-Charge.

Taking up/down steel tubing and connections including cleaning for refixing or removal to store 20 mm bore pipes ,complete all as specified and directed by the Engineer-in-Charge.

Taking up/down steel tubing and connections including cleaning for refixing or removal to store 40 mm bore pipes.

S&F 15 mm bore steel water Tubing 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors ,complete all as specified and directed by the Engineer-in-Charge.

All as per SI no 17 above but except pipe ,complete all as specified and directed by the Engineer-in-Charge.

S&F 20 mm bore steel water Tubing 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors ,complete all as specified and directed by the Engineer-in-Charge.

All as per SI no 19 above but except pipe ,complete all as specified and directed by the Engineer-in-Charge.

S&F 40 mm bore steel water Tubing 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors ,complete all as specified and directed by the Engineer-in-Charge.

All as per SI no 21 above but except pipe ,complete all as specified and directed by the Engineer-in-Charge.

S&F 20 mm Gun metal , global or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in repair ,complete all as specified and directed by the Engineer-in-Charge.

S&F 40 mm Gun metal , global or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in repair ,complete all as specified and directed by the Engineer-in-Charge.

M&L for cutting chases in stone concrete block or slab, walls , pinning in , making good to facing where required and pointing in cement mortar 1:3 to ends of edges of landing steps, cills, sunshed, shelves, lintels, etc ; and cutting chease for water tubing or concealed conduit wiring , etc, and making good cutting not exc 10 cm girth ,complete all as specified and directed by the Engineer-in-Charge.

Demolition of un-reinforced cement concrete in roofs,floors ( other than ground floors), beams, staircase, landing, chajjas and similar suspended work.of and pavings not xceeding 15 cm thickness(below or above ground level) complete all as specified and directed by the Engineer-in-Charge.

M&L for 75 mm thick Cement concrete type D-2 , 1:4:8 using 40 mm graded aggrigate as in subbase complete all as specified and directed by the Engineer-in-Charge.

Demolition of stone slabs and tiles laid bedded and pointed in any mortar of any description or thickness in floors, aprons etc complete all as specified and directed by the Engineer-in-Charge.

M&L for machine pressed precast conrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 grade laid over and inclusive 30 mm thick sand filling complete all as specified and directed by Engr-in-Charge

M&L for machine cut kota stone slab flooring 18-20mm thick over 15 mm th cement screed in CM 1:4 base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by the Engineer-in-Charge.

All as per SI no 30 above but as in skirting/dado etc. ,complete all as specified and directed by the Engineer-in-Charge.

S & F reflective chequered cement concrete tiles 30 cm by 30 cm by 25 mm thick, with grey cement and pigments, set, jointed over 10 mm thick screed bed in CM 1:4, and pointed in neat cement slurry in floors complete all as specified and directed by the Engineer-in-Charge.

Dismantling floor,hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by the Engineer-in-Charge.

M&L for non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement lurry and pointed in white or coloured cement to match including 15 mm screed bed 1:4 cement mortar complete all as specified and directed by the Engineer-in-Charge.

M&L for non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed with spacer and laid with epoxy grout in neat cement slurry and pointed to match including 15 mm screed bed 1:4 cement mortar complete all as specified and directed by the Engineer-in-Charge.

M&L for glazed ceramic tiles 300x450x7 mm to 8mm thick in vertical surfaces such as skirting, dadao and risers to steps over 10 mm thick in CM(1:4) incl taking down from existing surfaces complete all as specified and directed by the Engineer-in-Charge.

M&L for vitreous china wash down water closet (pedestal pattern) white complete, including connection to drain pipe and to flushing pipe antisyphonage pipe etc, fixed in repair,,complete all as specified and directed by the Engineer-in-Charge.

M&L for plastic water closet seat, closet pattern with flat bottom and cover and incl mild steel chromium plated or aluminum hinges device complete fixed in repairs , ,complete all as specified and directed by the Engineer-in-Charge.

S&F flush pipe with rubber washer in repairs of PVC 32 mm dia for low level cistern pipes, ,complete all as specified and directed by the Engineer-in-Charge.

S & F for waste pipe in repairs of dia 32mm for WHB/Sink, ,complete all as specified and directed by the Engineer-in-Charge.

S & F for waste pipe in repairs of dia 40mm for WHB/Sink, ,complete all as specified and directed by the Engineer-in-Charge.

S&F in repairs 32mm bore dia of CP brass waste coupling suitable for WHB, ,complete all as specified and directed by the Engineer-in-Charge.

S&F in repairs 40 mm bore dia of CP brass waste coupling suitable for Kitchen sink ,complete all as specified and directed by the Engineer-in-Charge.

M&L for health faucet, brass, chromium plated, with 1000mm long 8mm dia chrome finish flexible pipe with wall hook, fixed in repairs c,complete all as specified and directed by the Engineer-in-Charge.

Dismantling water tanks of exceeding 500 & not exceeding 1000 ltrs and removing to store,complete all as specified and directed by the Engineer-in-Charge.

S&F rotational moulded polyethylene water storage tanks three layer construction white in colour, ( cylindrical vertical with closed top) IS 12701-1996, hoisted and fixed in position all as specified in SSR Part-I of Capacity 500 litres including all fitting accessories, complete all as specified and directed by the Engineer-in-Charge.

S&F 20 mm ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed in position complete all as specified and directed by the Engineer-in-Charge.

M&L for 50 mm thick Cement concrete type C-2 , 1:3:6 using 40mm graded aggrigate Finishing surfaces of concrete topping even and fair finishes (without using extra cement) as in plinth protection/leveling course all as specified and directed by Engr-in- Charge.

S&F jet spray, brass, chromium plated, heavy duty, including flexible pipe suitable for 15mm bore water connection; for EWC fixed in repair ,complete all as specified and directed by the Engineer-in-Charge.

S&F in repairs stainless steel wire cloth of 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainless steel wire staples, ,complete all as specified and directed by the Engineer-in-Charge.

Taking down shutters and refixing in same opening shutters of any descp exc 1 sqm but n.exc 2 sqm complete all as specified and directed by the Engineer-in-Charge.

S&F in repairs MS helical door spring 300mm size including roller and roller plate fixed to wooden or steel frames with welding/fitted with screws etc, ,complete all as specified and directed by the Engineer-in-Charge.

S&F in reapirs MS powder coated curtain rods with bracket fixed to wall with suitable screws and onion type end brackets all as per approved design/colour/pattern fixed ,complete all as specified and directed by the Engineer-in-Charge.

S&F Aluminium powder coated (match with door shutters) Hydraullic door closer suitable for aluminium glass door shutters of 851 to1000 mm in width and of weight between 61 to 80 kgs and fixed. ,complete all as specified and directed by the Engineer-in-Charge.

S&F Mortice lock with two lever MS body (vertical type) 100mm length of latch with 3 set of keys fixed in door shutter with proper in position complete complete all as specified and directed by the Engineer-in-Charge.

Checking of plumbing work ,joinery (wooden/steel) iron/aluminium mongery, pelmet box, door springs etc requiring carpentry/plumbing work and carrying out minor repairs such as tightening of screws/nails, minor adjustment of joinery, door /windows, water taps, stop cocks, water tank, water supply pipe line etc. by means of planer/chisling etc. including petty repairs material like screws/nails, plug etc. to make it functional, complete all as specified and directed. Note : 1. Any items required to be replaced shall be paid under respective items and in that case those items shall not be measured and paid. 2. The contractor or his authorised rep shall collect the complaint of all carpenter work from complaint cell /Engr-in-charge daily and all complaint will be rectified by the contractor with in same day than the returned the complaint slip after completion of complaint and get recipt from concered JE/Engr-in-charge .If he fails to complete the work with in same day then recovery will be made @50.00 per day .

M/S GURU DEV BUILDERS

M/S PARDEEP KUMAR

joginder singh and sons

JOGINDER SINGH