Loading
Loading…
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Tender Value
₹16.3 Cr
EMD Value
₹9.6 L
Closing Date
20 Feb 2026, 3:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Yes (up to 3 members)
No
Two Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
90 days
Expenditure
Capital (Works)
Above/Below/Par
WORKS
14 conditions · 3 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-I, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
The tenderer must have successfully completed any of the following during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or One similar work each costing not less than the amount equal to 60% of advertised value of the tender
Similar nature of work : Definition of single similar work: Any CLS or PI or RRI or EI or IBS/IBH or Double Distant work involving indoor and outdoor signalling work. Note 1: Tenderer may be required to submit the schedule of those works, Completion/Performance Certificates of which have been submitted by him/her in support of 30/40 /60 %(as the case may be) criterion of similar nature of work Note 2: a) Submission of 'Undertaking by the tenderer' that the equipment for EI or Axle Counter or AFTC or UFSBI shall be procured from RDSO approved sources and installation, testing and commissioning of EI or Axle Counter or AFTC or UFSBI shall also be got done from the same source including after sales support required during the warranty period AND b) After the award of the contract, MOU with RDSO approved source covering supply of equipment of EI or Axle Counter or AFTC or UFSBI. Installation, testing & commissioning of EI or Axle Counter or AFTC or UFSBI by the same RDSO approved source including after sales support required during the warranty period before supply of equipments is undertaken.
24 conditions · 10 needing a document upload
PAN card Copy should be enclosed.
Please submit the copy of the registration certificate as applicable, GSTIN certificate should be enclosed
Firm has to submit authorization letter for uploading documents on IREPS in case he/she is not an authorized person.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Tenderer should go through Annexure 1 & 2 of Tender Notice (attached in Tender Document)for list of documents required to be uploaded along with the offer
No post tender correspondence for submission of additional documents shall be entertained after opening of the Technical & Commercial offers. Even suomoto post tender letters of the tenders shall be treated as Null & Void
(i)Tenderers will examine various provisions of the Central Goods and Service Tax Act, 2017(CGST)/Integrated Goods and Service Tax Act,2017(IGST)/Union territory Goods and Service Tax Act,2017(UTGST)/respective states State Goods and Service Tax Act(SGST) also, as notified by Central/States Govt. and as amended from time to time and applicable taxes before bidding. Tenderers will ensure that full benefit of Input Tax Credit(ITC) likely to be availed by them is duly considered while quoting rates. (ii) The successful tenderer who is liable to be registered under CGST/IGST/UTGST/SGST Act shall submit GSTIN along with other details required under CGST/IGST/UTGST/SGST Act to railway immediately after the award of contract, without which no payment shall be released to the contractor. The contractor shall be responsible for deposition of applicable GST to the concerned authority. (iii) In case the successful tenderer is not liable to be registered under CGST/IGST/UTGST/SGST Act, the railway shall deduct the applicable GST from his/their bills under reverse charge mechanism(RCM) and deposit the same to the concerned authority
Provision of Double Distant signal on "B" route over Lucknow Division
P-II-LKO-SnT-DD-B-ROUTE
P-II-LKO-SnT-DD-B-ROUTE
Open
Works - General
24 Months
Unknown (Unspecified Location)
₹0
₹9.6 L
20 Feb 2026
29 Jan 2026
64 items across 1 schedule · ₹16,27,05,940.41 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | Excavating and refilling of trench to the level of ground with rammed earth as per Drg. No(NR/S&T/Con/1.1/97A) so as not to form a drain 0.3 Mtrs wide & 1mtr deep on both side of the station alongside the track. It shall conform to the safe distance as per signalling and cable plan in all type of soil, it also includes clearence of roots of trees and bushes Lesser depth due to site condition shall be paid proportionatly, after being certified so by site incharge. | Metre | 289800.00 | 60.2 | 1,74,45,960 |
| 2 | Excavating and refilling of trench 0.3 Mtrs wide & 0.8 mtr deep on pitched/stone/bricks paved surface,road/crossing/platform etc. and restoration of surafce to original condition. | Metre | 2700.00 | 139.7 | 3,77,190 |
| 3 | Laying of signalling / telecomm / power cable of different cores as per Drg No(NR/S&T / Con /1.1/ 97C) and as per cable route plan approved by Railway through trenches, RCC pipe, DWC pipe, GI pipe etc. Meggering of cable should be done before and after laying.Cable will be made available at the store of concerned SSE/Sig or any other store N. Railway. Contractor has to transport it to work site at his own expenses. | Metre | 971000.00 | 7.13 | 69,23,230 |
| 4 | Supply and laying of second class bricks in the trench and laying as per Drg. No. (NR/S&T/Con/1.1/97A) and as per instruction of the site Engineer. [8*laying of cable] | Numbers | 2340000.00 | 7.19 | 1,68,24,600 |
| 5 | Termination of all the cores of all type of outdoor cables after its laying on both end.This also includes preparation of test report for core to core and core to earth on prescribed proforma for each core of the cable separately. This also includes dressing and lacing of cables on both ends.Proforma for testing and material for lacing to be supplied by the contractor. | Numbers | 28000.00 | 13.33 | 3,73,240 |
| 6 | Supply of terminal block M-6 (ARA terminals) Block 25mm centre small M-6 terminal made of PBT as per IRS spec. No.IRS-S-75/2006(Rev.2) & IRS drawing No. SA-23741/A (ALT.4) or latest. IInspection by RDSO | Numbers | 28000.00 | 75.76 | 21,21,280 |
| 7 | Supply of 4 conductor disconnect terminal block for test and measurement 0.8 sq.mm- 2.5 sq.mm centre marking with test slot for test plug 2mm/0.079IN and 2.3mm/0.091IN carreir rail DIN 35 front entry cage clamp connection Grey wago or similar as RDSO/SPN/189/2004 Ver.2.0 or latest. Inspection by RDSO/RITES | Numbers | 28000.00 | 140.4 | 39,31,200 |
| 8 | Supply of Steel carrier Rail 35x7.5mm/0.039 in thick unslotted, yellow with Chrome Wago or similar as per RDSO/SPN/189/2004 Ver.2.0 or latest. Inspection by RDSO/RITES | Metre | 1120.00 | 154.06 | 1,72,547.2 |
| 9 | Supply of End and Intermediate Plate 2.5mm/0.098 in Thick RDSO/SPN/189/2004 Ver.2.0 or latest. Inspection by RDSO/RITES | Numbers | 28000.00 | 19.48 | 5,45,440 |
| 10 | Supply of screw less end stop 10mm/0.394 in wide carrier rail DIN 35 Grey Wago or similar as per RDSO/SPN/189/2004 Ver.2.0 or latest. Inspection by RDSO/RITES | Numbers | 2800.00 | 16.37 | 45,836 |
| 11 | Boring and trenchless cabling along with supply and insertion of HDPE self lubricated pipes as per RDSO spec no. RDSO/SPN/204/2011 VER 1.1 of 50 mm/120mm dia with 6mm wall thickness in the bore at the depth of 1.4 meter to 2.1 meter from formation level(level of earth below ballast) as per drawing and as directed by engineer incharge by trenchless technology for laying of signalling /telecom/power cable under track /culvert etc. cable laying covered seperately.The following required coupling arrangeemnt should also be supplied: 1. Suitable snap fit couplers with rubber O ring, 2. Spacers, 3. Tees. 4. Bend. 5. End Cap(1 no=6mtr , straight pipe). (A) The cost shall include horizontal boring through any intermediate obstruction, either natural or manmade or any boundary etc. (B) The rate is inclusive of all the materials equipment and labour required for during trenchless horizontal boring under the railway track. Nothing extra shall be admissible on any account than the rate quoted above. (C) The Pipe is to be laid under railway track/road /culvert. All necessary arrangeemnt are to be provide and all precautions are to be end is not deviated from the horizontal level line by more tthan 250mm in horizontal and vertical direction. (D) The rate shall be inclusive of direction and protection of underground utilities encountered during boring. (E) The payment for boring shall be made only when DWC HDPE pipe are laid in the bore. Inspection: RITES for supply portion. | Metre | 6850.00 | 1,664.2 | 1,13,99,770 |
| 12 | Supply and fixing of GI Pipe as per specification No. IS:1239 (ISI Mark) make Jindal/Tata/Ajanta or Similar, size 75mm dia 3mm thick perforated at a distance of 20 cm or less of required length at culvert/bridges/along the cuttings, , suitably concreted at both ends as per drg. No. (NR/S&T/CON/1.4/97) to be filled with chattered compoun. GI pipe clamps of MS flats, bolts and nuts, chattered compound to be supplied by contractor .Inspection: Consignee for supply portion | Metre | 500.00 | 922.43 | 4,61,215 |
| 13 | Casting,concreting and curing of foundation and erection of App. Case single as per Drg. No (NR/S&T/ Con/2.7/97). A layer of 3mm of Bitumen compound has to be provided between foundation and location box to prevent ingress of water in the base of location box. All material such as cement, sand, aggregate & anchor bolts shall be supplied by the contractor. Contractor is required to execute all type of repair work of foundation if required during inserting the cable for termination. | Numbers | 112.00 | 5,189.89 | 5,81,267.68 |
| 14 | Supply of Apparatus Single with 'E' type locks and key ward No 42 complete as per drawing No. RDSO/S-11500 or latest. Handle should be at the rate of one each 4 nos appratus case. Inspection: RITES | Numbers | 112.00 | 21,191.77 | 23,73,478.24 |
| 15 | Provision, preparation & fixing of backlite hylum sheet 910x600x6mm. Funiture class wooden shelf of size 900x450x25mm duly fixed by angle iron piece of different size inside the single app case. Hylum board shall be fixed on angle iron frame of 25mmx25mmx3mm. Angle iron frame will be fixed in loction boxes secured by nuts and bolts. This includes wiring, fixing of fuses, ARA terminal, fixing of Shelf type, 'Q' series relays & other type of relays on squire bars, fixing & jamming of cable with 2" salwood plank provided at the bottom. This will includes opening, passing & jamming armour of each cable in the hole drilled separately for each cable through salwood plank & all cable entry points on location boxes, location huts,JBs, relay room/batt room to be closed with suitable masonary works covered with sand and plastering, writing description of terminal, drawing of circuits inside app. case. Painting from outside as well as inside with Red Oxide & Aluminium paint is covered separately. Size of lettering to be 100mm & as per site engineer's instruction.All materials such as teakwood shelf, hylum board, salwood plank,angle iron, square bar, nuts &bolts etc. shall be supplied by the contractor. ARA terminal & HRC fuse will be supplied by the Railway. (i) App. case single involving wiring of relays | Numbers | 112.00 | 5,526 | 6,18,912 |
| 16 | Supply of apparatus case steel half with 'E' type locks and key ward No. 42 as per drawing No. RDSO/S-11507 or latest. Handle should be at the rate of one each per 4 Nos apparatus case. Inspection: RITES | Numbers | 224.00 | 17,147.15 | 38,40,961.6 |
| 17 | Casting, concreting and curing of foundation and erection of app. Case half as per Drg, No (NR/S&T/ Con/2.8/97). A layer of 3mm of Bitumin compound has to be provided between foundation and location box to prevent ingress of water in the base of location box. All material such as cement, sand, aggregate & anchor bolts shall be supplied by the contractor.Contractor is required to execute all type of repair work of foundation if required during inserting the cable for termination. | Numbers | 224.00 | 5,190.99 | 11,62,781.76 |
| 18 | Provision, preparation & fixing of backlite hylum sheet 450x600x6mm. Furniture class wooden shelf of size 450x450x25mm duly fixed by angle iron piece of different size inside the half app case. Hylum board shall be fixed on angle iron frame of 25mmx25mmx3mm. Angle iron frame will be fixed in loction boxes secured by nuts and bolts. This includes wiring, fixing of fuses, ARA terminal, fixing of Shelf type, 'Q' series relays & other type of relays on squire bars, fixing & jamming of cable with2"salwood plank provided at the bottom. This will includes opening, passing & jamming armour of each cable in the hole drilled separately for each cable through salwood plank & all cable entry points on location boxes, location huts,JBs, relay room/batt room to be closed with suitable masonary works covered with sand and plastering, writing description of terminal, drawing of circuits inside app. case. Painting from outside as well as inside with Red Oxide & Aluminium paint is covered separately. Size of lettering to be 100mm & as per site engineer's instruction.All materials such as teakwood shelf, hylum board, salwood plank,angle iron, square bar, nuts &bolts etc. shall be supplied by the contractor. ARA terminal & HRC fuse will be supplied by the Railway. (i) App. case half not involving wiring of relays | Numbers | 112.00 | 3,607.15 | 4,04,000.8 |
| 19 | ii)App. case half involving wiring of relays | Numbers | 112.00 | 4,053.29 | 4,53,968.48 |
| 20 | Supply and installation of earth electrodes as per std. practice. The item includes digging of pit in earth, 3 Mtrs. deep and fixing earth electrode pipe. Casting of cement concrete enclosures as per drg. No. (NR/S&T/CON/6.4/97). The soil treatement shall be done as per std. pratice. The item includes provision of mild steel flat of size 35mm x 6mm (as per IRSEM) and nut bolted connection of MS flat with earth electrode. The other end of mild steel flat to be connected to block instrument, cable sheath of power equipment, signal base, apparatus case, CT rack / relay racks, other equipments as per the instruction of Engr. at site & IRSEM. Earhting connection location to location shall be done through cable which shall be provided by Railway. Complete materials such as earth electrodes as per drg. No. ( NR/S&T/CON/6.3/97), cement, wiring material, nut bolt for connection & mild steel flat of size 35mm x 6mm or 210 sqm as per SEM etc. to be supplied by the contractor. Inspection: RITES for supply portion | Per Earth | 448.00 | 3,720.95 | 16,66,985.6 |
| 21 | Casting,concreting and curing of foundation of main signal as per Drg No. NR/S&T/Con / 2.1/97. All material such as Anchor bolts cement, sand, aggregate to be supplied by the contractor. | Numbers | 112.00 | 10,536.07 | 11,80,039.84 |
| 22 | Fixing of CLS surface base, bolting on the foundation. Erection of CLS post with signal unit on the top or on an offset bracket and fitting ladder and guard to the post at the top Concreting ladder base and embedded into the ground with supporting bracket in the middle. Blanking of the ladder for a distance of 1 feet between the height 6'9"and 7'9"from the rail level by MS angle and MS sheet 0.6mm thick wherever required. This includes provision of wooden ( sal ) cross arm 1Mx1M for CLS unit prior to the commissioning, fixing of AC / DC lit LED Signal unit and hood on CLS unit,wiring the CLS unit and fixing the signal.Elevation and distance of foundation from track shall be in accordance with schedule of dimension for Indian Railway published by Government of India & approved Drawings. All items for the above work except items mentioned in Annx B-2 shall be supplied by the contractor including following items. (i) U bolt for offset bracket. (ii) Wooden cross arm 1Mx1M (iii) MS sheet and MS angle for blanking of ladder (iv) Wire mesh guard, U-lock for unit , nuts and bolts etc for the following.(a) 3/4-aspect of colour light signal. | Numbers | 112.00 | 4,319 | 4,83,728 |
| 23 | Supply of CLS Signal post 4.6 Metre and ladder 4.5 M with bases ( 140mm dia, tubler) and platform confirming to IRS:S-6-81 and Drg. No 2011/M and for the ladder RDSO Drg No. SA- 23153(adv)or latest .Inspection: RITES | Numbers | 112.00 | 20,501.59 | 22,96,178.08 |
| 24 | Fabrication, Supply and fixing of retroreflective P/G/C markers with complete fittings as per approved Drg. No. NR/S&T/CON/6.2/97. All material required for the job such as MS sheet, MS angle. Nut and bolts, paint and painting materials will be supplied by the Contractor. The P and G markers shall be as per Drg. No.S 23456(Adv) & SA 23477(Adv) respectively. Inspection by Consignee for supply portion | Numbers | 112.00 | 811.38 | 90,874.56 |
| 25 | "Supply of colour light signal unit 3/4-Aspect complete without lamp holder, lamp, lense and signal transformer as per IRS-S-26/64 & RDSO Drg No , SA-23002 A/M(Adv) or latest, SA- 23001 A/M(Adv) or latest with hand cuff lock 2 No.Inspection: RITES | Numbers | 112.00 | 21,325.67 | 23,88,475.04 |
| 26 | Supply of Relay plug in type, style AC LED all aspect AC lamp proving relay.Unit with in built current transformer type slow to release neutral line relay 4F/4B contacts, front & back contacts metal to carbon, shall be suitable for working in series with the 100 V AC, LED signal lamp rated at 15 W confirming to RDSO spec STS/E/Relays/AC Lit LED signal/09-2002 Amdt 1 or latest, BRS:941A, IRS-S- 34 & IRS-S-23/88, as applicable. The interlocking code for this unit shall be ABDHK type.Inspection: RDSO | Numbers | 336.00 | 4,855.98 | 16,31,609.28 |
| 27 | Supply of Relay AC immune ,plugin type,style QNA1,DC neutral line relay,24V DC 8F/8B contacts,front & back contacts metal to carbon with plug board retaining clip & connectors confirming to BRS-931A,IRS:S60/78 IRS:S34/68 & IRS:S-23/88 as applicable.The interlocking code for this unit shall be ABDGH or latest.Inspection: RDSO | Numbers | 560.00 | 4,911.58 | 27,50,484.8 |
| 28 | Supply of Relay,Non AC immune ,plug in type,style QN1,DC neutral line relay,24V DC 8F/8B contacts,front & back contacts metal to carbon with plug board retaining clip & connectors confirming to BRS-931A,IRS:S60/78 IRS:S34/68 & IRS:S-23/88 as applicable.The interlocking code for this unit shall be ABCDF or latest.Inspection: RDSO | Numbers | 1120.00 | 4,056.47 | 45,43,246.4 |
| 29 | DC neutral line relay QNA1K (QSA3), AC immune, DC neutral line 24V, 12F/4B contacts, complete with plug board, retaining clip and connectors. Conforming to BRS 930A, (as applicable) IRS:S34 & IRS:S23 or latest.Inspection: RDSO | Numbers | 336.00 | 6,390.47 | 21,47,197.92 |
| 30 | Supply of wiring materials as per IRS spec. No. IRS-76/89 with amendment no.2 or latest Copper wire, PVC sheathed & PVC insulated sizes as under: (a) Power wire 1x6 sq mm (RED & BLACK colour) .Wire to be procurred from RDSO approved source.Inspection by consignee. | Kilometre | 5.00 | 59,860.21 | 2,99,301.05 |
| 31 | "Fabrication, supply and fixing of relay rack of size 2200mm x 690mm along with scaffolding as per as per Drg. No. NR /S&T/ CON/ 4.3/97-A made of angle iron of size 45mmx 45mm x 6mm along with outer frame made of angle iron of size 65mm x 65mm x 8mm fitted with M.S. Squares bars duly ionized, descriptions strips to accommodate pluging -type relay/groups/points contractor units /ECRs/HMUs. All fixing material like anti-tilting device, hylam sheet (Grade P2) of 6mm thickness if required, bolts & nuts, washers, insulator, shoe, angle iron flats, L-bolts, catenary wires and cement concrete etc will be suppled by contractor. This includes cleaning, priming by red oxide, painting & description etc. with ISI mark paints. Inspection by Consignee." | Numbers | 27.00 | 19,214.73 | 5,18,797.71 |
| 32 | Wiring of relays in relay room/relay huts/location box as per appd wiring diagrams. All wiring material including resistances and condensers and wires etc.to be supplied by contractor . It also includes dressing, bunching , lacing and fixing of relay bases. | Numbers | 2352.00 | 501.56 | 11,79,669.12 |
| 33 | "Design,Fabrication and supply for Alteration in existing Electronic Interlocking ,Alteration in existing operating panel Modification to existing Interface & Logic Circuits, Application software of VDU & MT, Alterations to the Relay Racks wiring as per the modified Interface circuits along with the supply of necessary wiring material and required Input/output cards and any other type of card,PCB,DC-DC module of Mini IPS , All types of relays and racks for relays & EI equipments, fixture mounting arrangements, fully wired Domino with LED for existing operating panel and accessories necessary to make EI system functional. It includes Installation ,Factory Acceptance Test & Site Acceptance test as per the modified application logic and Commissioning as per RDSO specification No. RDSO/SPN/192/2005 or RDSO/SPN/192/2019 or latest with amendments, as per special condition of contract and technical specifications (including all relevant and latest RDSO Technical Advisory Note (TAN)) and SIP enclosed.It also includes : " Supply of "As built" documents (i) Technician / Jr. Engineer (Installation and Maintenance Level) - Manual for Installation, Testing, Commissioning and Maintenance of the System (6Sets for each EI). (ii) EngineerLevel - Technical & System Module for diagnostic & Troubleshooting for Repair centre (6Sets for each EI). (iii) HigherManagement Level - Functioning and System Over View (6 Sets for each EI). (iv)Completion Documents as per special condition of Contract (6Sets for each EI). (v) Supply ofdocuments as per Technicalspecification Para - 10.1 ofRDSO Specification no RDSO/SPN/192/2005 (6 Sets for each EI). It also includes : "wiring, testing, validation of additional relays in data logger system . The contractor shall supply all the accessories to make VDU/MT functional with EI system through OFC connectivity. It also includes any other accessories required (like simulation panel, lamp board etc.) to make EI system functional. System must be compatible with working in RE area. Inspection: RDSO for supply portion - Any sub item which is not inspected by RDSO will be inspected by Consignee). " | Numbers | 16.00 | 26,37,579.47 | 4,22,01,271.52 |
| 34 | Supply and fabrication of domino units with cover plates and LED as per approved panel diagram, each of size 54x34mm completely wired up similar to Electrostar make .Each domino unit should have all the 15 contact terminals wired up as per technical specification. color of Panel button or LED with domino should be as per panel diagram & instruction of site engineer .Inspection: Consignee for supply portion. | Numbers | 110.00 | 1,179.96 | 1,29,795.6 |
| 35 | Supply of 200 way tag blocks conforming to drg no. SA-24751 or latest and as per IRS:S- 77/2006(Rev.1) or latest with latest Corr/Rev./Amdt. Inspection by Consignee | Numbers | 112.00 | 1,369.41 | 1,53,373.92 |
| 36 | Fixing, wiring & soldering of 200 way tag blocks, conforming to drg No .SA-24751 or latest and as per IRS:S-77/2006(Rev.1) or latest with latest Corr/Rev./Amdt., on cable termination rack/relay rack/block rack/HV rack as per Drg.No.NR/S&T/CON/4.3/97A. | Numbers | 112.00 | 171.69 | 19,229.28 |
| 37 | Modification of the existing domino type operating cum indication panel as per approved panel diagram | Numbers | 11.00 | 4,216.88 | 46,385.68 |
| 38 | Supply and installation including wiring of DC-DC converter in IPS 10A(24-40V) make M/s HBL,Amarraja or Statcon.All wiring material,connectors,lugs for installation to be provided by contractor.Inspection: RDSO for supply portion. | Numbers | 112.00 | 25,488 | 28,54,656 |
| 39 | "Supply of electric fuse complete with fuse block (base) for Railway signalling non detoriorating type low voltage fuse assembly 0.63A/2Amp/6Amp/10A/16Amp. to suit . Specn. No.IRS: S-78/2006 and fuse block made of PBT/Polycarbonate as per IRS:S-75/2006 (Rev.2 & Amd.2) and drg no. 23748 (IRS), Alt-4 or latest. Fuse block shall be suitable for round head type fuses. Inspection by- RDSO." | Numbers | 2240.00 | 190.96 | 4,27,750.4 |
| 40 | Supply of electronic Cable Route Locator/Tracer equipment of C-scope/Stanley/3M make or similar RDSO recommended. (i) Cable avoidance tool DXL2 digital under ground cable & pipe locating receiver and cable avoidance tool. (ii) SGV2 signal generator. (iii) Signal lamp accessory ST- SC. (iv)Carry bag ST-CB and as per technical specification.Inspection - RITES | Numbers | 8.00 | 3,14,383.77 | 25,15,070.16 |
| 41 | Fabrication, supply and fixing of concrete cable marker as per RDSO drg. No. SDO/Cable Laying/020, dt.31.10.11. The marker shall be fixed at various places of cable route as per instruction of Eng. at site. Inspection by Consignee. | Numbers | 4830.00 | 1,398.38 | 67,54,175.4 |
| 42 | Supply and installation of RFID electronic marker for S&T underground cable wlth progammble memory for saving the user specific data inside the RFID electronic marker memory chip,later recordable by electronic marker locator during locating(1O cm diameter with floating coil to keep detection circuit always Horizontal for better detection) which can be buded to depth of 5ft Placing in trench. Inspection by RITES FOR SUPPLY PORTION. | Numbers | 2500.00 | 2,729.72 | 68,24,300 |
| 43 | Supply of Megger 500V/100V AC Philips or similar make . Inspection by Consignee | Numbers | 8.00 | 6,768.15 | 54,145.2 |
| 44 | "Supply of tool kit for JE/SE/SSE for Maintenance as per tech spec. given below: (1) Digital Multi Meter suitable for axle counter ranges 20 Amp AC/DC make protek 506 or similar- 1 no. (2) Digital clamp Multi Meter range up to 100 Amps for AC/DC current make SEW or similar - 1 no. (3) Leather Tool Bag for keeping tool kit -1 no. 4) Plier Sealing with sealing code bit -1 no. (5) Plier Wire Cutting 8"" make Taparia or similar -1 no. (6) Nose Plier 4"" make Taparia or similar -1 no. (7) Wire Stripper - 1 no. (8) Screw Driver set mutli port type -1 set (9)Track shunt resistance 0.5 ohm -1 no. (10) Soldering Iron 230V AC/65 watt -1 no. (11) Soldering Iron 230V AC/35 watt with diffrerent type replacement soldering head - 1 no. (12) Soldering Iron 110V AC/35 watt -1 no. (13) Mesuring Tape steel 30 meters - 1 no. (14) Mesuring Tape steel 3 meters - 1 no. (15) Rechargable Torch Superior quality -1 no. (16) File Flat 8"" long - 2 nos. (17) File Round smooth 8"" long - 2 nos. (18) File Flat Bsterred 8"" long - 2 nos. (19) Electric Drill Machine Portable 6mm make wolf or similar -1 no." Inspection by Consignee. | Numbers | 8.00 | 64,192.12 | 5,13,536.96 |
| 45 | Supply and installation of data logger failure analyser with configuration INTEL Core I-7, 4GB DDR3 SD RAM, cache 8MB, level 2, 500GB HDD or better or SSD for data input .It also include supply of 32'' LED FULL HD monitor, A-4 size Laser printer, online UPS 1KVA with 30min backup, computer table and chair.The data logger failure analyser should be compatible for configuration the system in case of any alteration in the yard interlocking in future. Inspection by Consignee | Job | 5.00 | 93,223.71 | 4,66,118.55 |
| 46 | Alteration/installation,wiring,testing,commisioning of datalogger as per RDSO spec no. IRS:S- 99/2006 or latest and as per techincal specification.execution shall be done by OEM. | Job | 11.00 | 19,631.71 | 2,15,948.81 |
| 47 | Designing , preparation of locking table, selection table, circuit diagram,contact analysis chart, relay rack chart etc; preparation of operating & indication panel Domino type diagram, (circuit shall be designed by the contractor with the use of Q series relays on the basis of approved signal Interlocking plan and obtaining approval of Competent Authority). The operating & indication panel may have addition & alteration to an extent of 5% variation in number of Domino.Designing should be as per Railway specifications and as per latest rules prescribed by Rly. This also includes preparation of cable route plan,Cable core chart,Station working rule diagram, Power supply arrangement,Cable termination chart in relay room and location boxes,Location wiring plan,Cable insulation chart,Fuse analysis,Indoor circuit diagram,Track circuit jumper plan,Terminal and Contact analysis chart, Outdoor circuits and other outdoor diagrams and obtaining approval of the engineer as per following :- Supply of 6 copies of complete set of superior quality paper including one set laminated, properly bound in file with cushioned cover. Software backup of complete set in the form of CD (2 Nos.) One complete set of tracings Design through CAD. Drawings in A-3 size & plan in bigger size papers. (six sets) | Job | 56.00 | 52,945.56 | 29,64,951.36 |
| 48 | Supply, Installation, testing and commissioning of Electrically Operated lifting barrier assembly as per RDSO Spec. No. RDSO/SPN/208/2012 (version 2.0) or latest consisting of 2 nos. of electrically operated lifting barriers, 2 pedestals, 8 band circuit controller with limit switches, hand cranks, 2 electric motors, 110V AC, without centrifugal switch, 2 GI Boom in 4 sections of 8 feet each with 2 retroreflective stop boards, boom light boxes, MS counter weight, 2 nos. of boom support for resting boom etc. The item also consists of following items: a) Supply of motorized boom locking /unlocking assembly with electrical coil complete (1no. each) b) supply of level crossing gate control panel floor mounting type with swithches and buttons sheet metal fabricated, (1 No) c) Supply of push button for operating the gate with 2 NO/NC contact, green colour-close & Amberopen, Siemens or Kaypee or similar make (1 no.) d) Supply of solid state electronic flasher 24V DC operated (1 no. each). e) Supply of dual tone warning bell with 20W horn & 15W amplifier (2 no. each). It also includes fabrication, wiring, fixing of gate indication panel in Gate lodge/Goomty Inspection by RDSO for Supply portion. | Numbers | 2.00 | 6,15,436.13 | 12,30,872.26 |
| 49 | Supply of Electronic Timer relay, 24 V DC (60sec) Inspection by RDSO | Numbers | 2.00 | 3,627.57 | 7,255.14 |
| 50 | Supply, Installation & Commissioning of Emergency Sliding Boom complete with all accessories for L/B gate. Inspection by RITES FOR SUPPLY PORTION | Numbers | 2.00 | 2,88,049.73 | 5,76,099.46 |
| 51 | "Supply, installation and wiring complete KLCR and its box in location boxes, supply, installation, wiring of heavy duty push button, LED indicator on MS sheet as per N.R. practice for crank handle locking. This work includes fixing & wiring of magneto telephones as per instructions of the site Engr. This includes all materials such as heavy duty push button, LED indicator (10mm), MS sheet of 4.5mm thick, nuts and bolts, fixing materials for the magneto telephone, and wiring materials to be supplied by contractor. Inspection by RDSO FOR SUPPLY PORTION." | Job | 2.00 | 19,755.37 | 39,510.74 |
| 52 | Supply of Transformer 3KVA 230V/130/110V as per IRS Spec No.S-72-88 with latest amendment. Inspection by RDSO | Numbers | 2.00 | 15,085.33 | 30,170.66 |
| 53 | True RMS mini Clamp meter 100 Amp AC/DC make Metravi 4673 , fluke or similar Precision down to 1mA and 0.1mV, with resolution of min. 1 mA .100A AC/DC current measurement 600V AC/DC voltage measurement 20 Mohm resistance measurement The meter comprises of minimum additional facility of AC/DC voltage measurement, Resistance measurement, continuity measurement. with One year warranty and backlight display facility inspection :consignee | Numbers | 20.00 | 8,708.93 | 1,74,178.6 |
| 54 | Dismantling of lifting barrier/ gate leaves complete set along with winch , wire rope, boom locking arrangements.Alldismantled material to be transported and stack in the store of DY.CMM/AMV/LKO store depot or SSE/Sig/RRI/LKO or any other store of N.Rly as per consignee. Note :- Before dismantling joint survey is to be done with the site engr. and report to be submitted to the site engr. (1 Job= 1 Lifting barrier) | Job | 2.00 | 3,389.03 | 6,778.06 |
| 55 | Dismantling and releasing of single signal post which includes dismantling of signal fittings electrical and mechanical both wheel of sorts ,GI pipe , Pully stakes , wire run from cabin to signal post etc .All dismantled material to be transported and stack in the store of DY.CMM/AMV/LKO store depot or SSE/SIG/RRI/LKO or any other store of N.Rly as per consignee. Note :- Before dismantling joint survey is to be done with the site engr. and report to be submitted to the site engr. (1 Job= 1 Signal) | Job | 30.00 | 1,402.55 | 42,076.5 |
| 56 | Loading, Leading & unloading of released materials from site to the Dy.CMM/Alambagh store or any other store at Lucknow Division by contractor. | MT-Km | 1000.00 | 5.94 | 5,940 |
| 57 | Earth work for excavation and refilling around location boxes and signals etc. where necessary including 50M lead and 1.5M lift. The lead is to be measured from centre of gravity of location to the centre of filling and lift from main ground level. The earth work should be well rammed including breaking of clods, leveling and dressing etc. as per instruction of Engineer at site. | cum | 100.00 | 156.94 | 15,694 |
| 58 | Concreting unscheduled item in concrete of 1:3:6 ratio in cement, coarse sand and aggregate 25mm at different places in the yard and plastering top in fine plaster of 1:4 cement sand ratio. It also includes the excavation of earth as required at site and as per instruction of site in charge. The volume in cubic meters shall include the volume occupied by angle or flat or GI pipe required to be embedded in the casting. Cement coarse sand and aggregate 25mm are to be supplied by the contractor. | cum | 280.00 | 3,481.86 | 9,74,920.8 |
| 59 | Shifting of Apparatus case Single: It includes the Excavation of pit in and around the existing location boxes very carefully without damaging the working cables and shifting and turning the location boxes to clear of the infringment as instructed by the railway repsentative at site. The work includes ensuring the safety of the signalling system, releasing the cables coils to give access for shifting/ turning the location boxes. Necessary masonary work and earth work in and around the location boxes to the required level shall be done as instructed by the Railway representative at site, if the existing earth connection to the location boxes are disturbed the earth wires shall be the properly reconnected. (All materials required for the work shall be supplied by the contractor). | Numbers | 30.00 | 4,457.26 | 1,33,717.8 |
| 60 | Shifting of Apparatus case Half: It includes the Excavation of pit in and around the existing location boxes very carefully without damaging the working cables and shifting and turning the location boxes to clear of the infringment as instructed by the railway repsentative at site. The work includes ensuring the safety of the signalling system, releasing the cables coils to give access for shifting/ turning the location boxes. Necessary masonary work and earth work in and around the location boxes to the required level shall be done as instructed by the Railway representative at site, if the existing earth connection to the location boxes are disturbed the earth wires shall be the properly reconnected. (All materials required for the work shall be supplied by the contractor). | Numbers | 30.00 | 2,950.81 | 88,524.3 |
| 61 | Engaging mechanical lifter or other machineries for lifting of location box , leveling the formation, dismantling any infringing structures, clearing and removing debris etc with all lead and lifts etc., complete and as per the instruction of railway representative at site. | Hour | 50.00 | 1,032.61 | 51,630.5 |
| 62 | Cleaning, scrapping, painting & lettering of all newly installed & existing gears such as signals, point equipment, track circuit equipment with TC No. on rail, apparatus cases, JB, TLJB, point Roding, cranks, compensators etc. including gate equipment if existing in station section as per the provision of IRSEM. All paints (ISI marked) shall be approved by Railway Engineer and painting materials to be supplied by the contractor. This includes writing, and painting requirement of all indoor and outdoor gears along with marking of all circuit Nos. near terminal and terminal boards/rack in apparatus cases, Jn .boxes, relay room, SM room, writing of relay nomenclature, fuse Nos. and equipment nomenclature as per the approved plans and as per provision of IRSEM. (1 JOB = 1 Station) | Job | 27.00 | 24,282.93 | 6,55,639.11 |
| 63 | Supply and provision of straight through joints thermo shrink jointing kit with the help of thermo shrink jointing kit as per specifications, drawings and stipulations of tender documents and as per approved cable route plan at various locations for 06 Quad/04 Quad cable. Jointing kits to be supplied as per RDSO specification IRS:TC 77- 2012 (Rev.-3) or latest amendments . Inspection by RITES. | Numbers | 100.00 | 7,667.91 | 7,66,791 |
| 64 | Monthly Basis Hiring Services - MUV; 2000 Km; Outstation 24*7 Non AC MUV with sitting capacity of 4 or more people Mahindra Bolero Camper, Tata Xenon, Mahindra Imperio etc. | Vehicle- Month | 12.00 | 44,330.54 | 5,31,966.48 |
| Schedule total | ₹16,27,05,940.41 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
TDbroute-5finalBW_compressed_1.pdf
GCC_April-2022_2022_CE-I_CT_GCC-2022_POLICY_27_04_22.pdf
ACS1to10.pdf
CPROnotice.pdf
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .