SPECIAL REPAIRS TO BLDG NO EXCLUDING SERVANT QUARTER AT MILIT GIRINAGAR PUNE 411025

Amount

(B/R PORTION) Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc. 15 cm thickness (below or above ground level) and removing demolished materials from site all as specified and directed.

Demolition of reinforced cement concrete, (other than ground floors), shelves, chajjas, slabs and similar work carefully and matching to adjoining disturbed surfaces and removing demolished materials from site all as directed.

Dismantling single layer Manglore pattern or similar tiles in roofing including ridge tiles, stacking serviceable tiles for reuse and removing rubbish off the premises complete all as specified and directed.

M&L for Roof tiles, Mangalore pattern or similar tiles in roofing, interlocking at side joints, laid dry complete all as specified and directed.

All as per srl item no 4.00 here in before but except tiles complete all as specified and directed.

M&L for Ridges or hip tiles to suit mangalore pattern of roofing tiles, bedded and jointed in cement mortar 1:6 etc complete all as specified and directed.

Dismantling battens for tiles, shingle etc. of any size including tilting fillets spaced exc. 15 cm complete all as specified and directed.

M&L 2nd class hard wood clean sawn battens at 30 cm spacing having sectional area exc. 5 and not exc.15 Sqcm complete all as specified and directed.

All as per srl item no 8.00 here in before but fixing only complete all as specified and directed. NOTE:- Serviceable battens obtained from BOQ item No. 7.00 shall be reused under this item.

M&L for 2nd class hardwood, clean sawn, in scantling timber work including dismantling of old U/s scantling and removing rubbish off the premises all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets/AC boards, any thickness, including cover fillets complete all as specified and as directed.

M&L for anodised aluminium snap grid frame work of size 605 X 605 mm for false ceiling alongwith hangers 6 mm dia GI (upto 1200 mm length) adjusting leval fixed to roof by means of ceiling cleats made out of GI flat 40 X 3 mm size 60 mm long and expansion hold fasteners 12.50 mm dia 40 mm long and complete all as specified and as directed.

M&L for 12 mm thick decorative Gyproc grey waterproof gypsum board fixed or laid/inserted to aluminium framework fixed in jointless finish with jointing compound and tape as per manufacturer's instructions complete all as specified and directed. .

M&L for Eaves/weather boarding with 20mm thick fibre cement board (Non asbestos) and fixed with self drilling and tapping screws of CSK head and joints finished with jointing compound and fibre tape as per manufacturer's instructions complete of approved arch pattern, size, colour and shape including dismantling of old boarding/eaves board fixed in any position complete all as specified and directed. Make:- V-Board (Vishaka Indurstires Ltd)/Everest/Charminar/Ramco as approved.

Taking down chowkats or frames of wooden or steel exc 1.5 sqm & n.exc. 4 Sqm with Shutters (without taking off shutters from the frames) complete all as specified and directed.

M&L for pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified, supplied and fixed size 125X60 mm complete all as specified and directed.

M&L for pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified, supplied and fixed size 105X60mm complete all as specified and directed.

M&L for PCC 1:3:6 type C-0 (using 12.5mm graded stone aggregate) as in filling steel frames etc. incl necessary form work complete all as specified and directed.

M&L for 35 mm thick Flush shutters with lipping all around of solid core construction with block board core and ply wood face panels commercial type on both side complete all as specified and directed.

M&L for factory made 35mm thick 2nd class H/wood Glazed and skeleton shutters, open rebated and prepared to receive 12mm thick toughened glass, gauge etc. (with sash bars) edges of ramming plain, chamfered or rounded, fitted with cut of and mitred beads for securing glass, gauge etc of size of members of shutters as specified in SSR Part-I section 8 clause No. 8.2(a) and fitted to chowkats complete all as specified and as directed.

S&F Flush shutter solid core 35 mm thick with block board core and plywood face panels commercial type on both side and one face is covered with decorative face veneer with lipping/frame to match complete all as specified and directed by Engr-in-Charge

M&L for door viewers eye brass 75mm complete all as specified and directed.

S&F stainless steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm & fixed with stainless steel wire staples all as specified & directed.

M&L for Preparation of new/old wooden surfaces exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

M&L Framed work such as grills,gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, frame work of water tanks and similar work conforming to Fe-290.Gde-E-165 complete all as specified and as directed.

S & F in repairs MS plain black sheet 1.25 mm thick in hearths covering to doors shutters, chullah hood etc with plain 40mm lap joints or welded/riveted seams including bending, turning up, mitred angles etc. as required complete all as specified and as directed.

M&L for two coats of synthetic enamel paint over a coat of red oxide on new/old steel surfaces exc. 10 cm width or girth etc. complete all as specified & directed.

S&F for 300mm long brass sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified and directed.

S&F for 140 mm long brass body and tongue with hard drawn steel spring door stopper fixed to door bottom rail complete all as specified and directed.

S&F 150mm brass handles, cast type, polished bright complete all as specified and directed.

S&F 200mm long decorative brass barrel tower bolts, with cast or sheet barrel and rolled and cast bolts fixed complete all as specified and directed.

S&F in repairs readymade 9 feet pulley operated cloth drying system, aluminium anodised 22mm outer dia pipe, channel assembly, locking system to hide rope knot, ropes 4mm dia HDPE double core & fitting material etc. complete all as specified and directed. Make:Easy dry or equivalent and approved by EIC.

S&F 125mm, double action spring hinges, mild steel with steel wire spring, stove enamelled complete all as specified and directed.

S&F in repair Stainless steel fancy chromium plated 25mm dia as in curtain rods all as specified and directed

S&F Stainless steel chromium plated brackets suitable for 25mm dia curtain rod (minimum projection from wall 75mm) fixed in wall including drilling, rawl plug, screws etc. complete all as specified and directed.

S&F stainless steel chromium plated 6 Pin, 45Cm to 60Cm long hanger fixed to wall with screws complete all as specified and as directed.

Dismantling plain or corrugated steel sheeting any gauge thickness including Nainital or similar pattern roof covering complete all as specified and directed..

M&L 0.63mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with self tapping screws in roofs, walls with grade of zinc coating 275 complete all as specified and directed.

All as per item No. 39.00 here in above but fixing only except sheeting complete all as specified and directed.

M & L for 0.63 mm Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with self tapping screws in roof ,wall with grade of zinc coating 275 complete all as specified and directed.

S& F 2nd Class Hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and as directed.

S&F in repairs 18mm thick prelaminated particle board interior grade, conforming to IS-12823, Gde-I prelaminated both side with decorative choice lamination as in cupboard shutters, Kitchen cabinets etc fixed with screw including 3mm thick, ist class HW(TW) beading all around on edging to timber frame work all as specified and directed by Engr-in-Charge.

S&F continuous (Piano) hinges mild steel bright finished or electro galvanised width of flap 30mm complete all as specified and directed.

S&F 125mm cupboard handles fixed with nuts screws and washer of aluminium anodised complete all as specified and directed.

S&F Hasp and staples safety type aluminium with mild steel hinge pin including bolt to hinge plate and fixed with screws of 125mm size complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube, all as mentioned in Item No. 8095 of SSR Part-II. complete all as specified and directed.

S&F factory made solid panel decorative PVC door shutter 30mm thick (stiles) consisting of frame made out of M.S tubes for top & bottom rails; M.S frame shall be covered with heat moulded plain colour PVC ‘C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per manufacturer's instructions complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubish off the premises complete all as specified and as directed.

M & L for 25mm thick Cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in sub base or levelling course complete all as specified and directed.

M&L for non skid, ceramic tiles 7 to 8mm thick (Square/Rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 Sqm coloured tiles, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete over and including 15mm thick screed bed in CM 1:6 complete all as specified & directed.

S&F, glazed ceramic tiles coloured 450 x 350mmx 7-8 mm thick in wall/dado etc, set & jointed in neat cement slurry & pointed in white or coloured cement to match with & over rendering 15 mm thick in CM 1:6 on stone masonry surfaces or surfaces other than fair face of brick work/ concrete surfaces complete all as specified and directed.

M&L for coloured glazed ceramic highlighter tile of size 450 x 350mm x 7 to 8mm thick, colour and pattern as approved by GE, as in vertical surface set and jointed in neat cement slurry using grey cement and pointed in coloured cement to match the colour of tiles over and including 10mm thick screed bed in cement mortar 1:3 etc complete all as specified & as directed.

M&L for coloured glazed double charged vitrified ceramic tiles 9-10mm thick (square/Rectangular) polished, area of each tile not exceeding 0.36 sqm as in floors, set and jointed in neat cement slurry and pointed in coloured cement to match with tiles, laid over and including 20mm thick screed bed in CM 1:6 all as specified and directed by Engr-in-Charge.

M&L for coloured glazed double charged vitrified ceramic tiles 9-10mm Thick (square/Rectangular) polished, as in skirting, set and jointed in neat cement slurry and pointed in coloured cement to match with tiles, laid over and including 10mm thick backing coat in CM (1:3). all as specified and directed by Engr-in-Charge.

S & F in repairs Machine cut cuddappa stone slab one side polished 20 to 25mm thick, set and jointed in neat cement slurry and pointed in coloured cement to match, laid over and including 20mm screed bed in cement mortar (1:6) complete all as specified and as directed. .

M & L in repairs for granite 18mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

Rounding edges of stone one edge, such as in steps, cooking platform, window cill and other similar situation complete all as specified and as directed.

M&L for 75mm thick PCC 1:3:6 type C2 (using 20mm graded stone aggregate) as in plinth protection complete all as specified and as directed.

M&L PCC 1:2:4 (nominal mix) Type B-0 (using 12.5mm graded stone aggregate) in shelves, chajjas, slabs and similar work carefully and matching to adjoining disturbed surfaces all as directed.

M&L 40mm thick PCC 1:2:4 type B-1(using 20mm graded stone aggregate) as in flooring, finished even and smooth without using extra cement. complete all as specified and as directed.

Taking down cement plaster, any description on brick, concrete or stone walls or ceiling including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off outside MD land all as specified and directed.

Demolition of Brickwork or stone masonary built in Cement mortar including all quions, arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and as directed.

M&L precast cement concrete block masonry with solid block, type C-1,1:3:6 mix ( using 20mm graded stone aggregate ), exc 10cm in width and setting in cement mortar 1:6 complete all as specified and directed.

Racking out joints/pointing to random rubble or polygonal rubble uncoursed or brought up to courses buit in cement or cement lime mortar complete all as specified and as directed.

M&L for keyed pointing to random or polygonal rubble uncoursed or brought upto courses in cement mortar 1:4. complete all as specified and as directed.

M & L for Rendering 15 mm thick on stone masonry or concrete work in CM 1;6. finished even and smooth without using extra cement complete all as specified and directed.

M & L rendering 15mm thick on stone masonry surface or concrete surface finished even and smooth without using extra cement in cement mortar 1:4 complete all as specified and directed.

M & L for Rendering 10 mm thick of fair faces of brick work or concrete work in CM 1;6. finished even and smooth without using extra cement.

M&L 5 mm thick rendering in CM 1:3 on concrete surface of ceiling, finished even and smooth without using extra cement complete all as specified and as directed.

M&L for preparation of surfaces and applying 2 mm thick wall care putty on walls internally or externally on new/old plaster surface of walls complete all as specified and directed by Engr-in-charge.

M&L for two coats of oil bound distpemper over a coat of primer on New surfaces of wall including preparation of plastered surface of wall complete all as specified and as directed.

M&L for two coats of oil bound distpemper over a coat of primer on Old surfaces of wall including preparation of plastered surface of wall complete all as specified and as directed.

M&L for applying two coats of oil bound distpemper over a coat of primer on new surfaces of ceiling complete all as specified and directed.

M&L for applying two coats of oil bound distpemper over a coat of primer on old surfaces on old surfaces of ceiling complete all as specified and directed.

M&L for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/Litre and UV resistance as per IS 15489:2004, Alkali & Fungal resistance exterior paint of required shed (Company Depot Tinted) with silicon additives @ 1.43 Litre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 Lit/sqm over new/old surfaces including complete removal of existing paint by bio wash, necessary scaffolding required for painting work, safety measures etc complete all as specified and directed

M&L French polishing on surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on old works with two or more coats and applying one coat of touchwood complete all as specified and directed

S & F 100 mm butt hinges medium weight cold rolled mild steel and fixed complete all as specified and directed

S & F 150 mm long aluminium anodised barrel tower bolt complete all as specified and directed

S & F 150 mm Handles medium weight cold rolled mild steel complete all as specified and directed

S&F Gun metal globe or gate valve with iron wheel head screwed both ends size 20mm for iron pipe, fixed complete all as specified and as directed.

Taking down 15 mm bore steel water tubing and connections complete all as specified and directed.

Taking down 20 mm bore steel water tubing and connections complete all as specified and directed.

S&F for steel water tubes, 20mm bore medium grade, galvanized with & including all fittings and fixed complete to walls, ceiling or laid in floor complete all as specified & directed.

All as per item no 84.00 here in befor but 15mm complete all as specified & directed.

M&L for cutting chases, pinning in stone, concrete block walls making good to facings where required and pointing in cement mortar 1:3 for concealed water tubing and making good complete all as directed.

S&F in repairs 500 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position all as specified in SSR Part-I, connecting up pipes including 15 mm bore ball brass valves, high pressure, with polythene float and fly- nut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

S&F in repairs 1000 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position all as specified in SSR Part-I, connecting up pipes including 20 mm bore ball brass valves, high pressure, with polythene float and fly- nut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

S & F in repairs PVC connection 45 cm long 15 mm bore with 2 Nos PTMT check nuts complete all as specified and directed.

S & F in repairs vitreous china wash down water closet pan Pedestal any colour including fixing bolts etc including PVC seat cover white with flat PVC low level flushing cistern 10 Ltr capacity with all internal fitting, inlet, outlet pipe connections etc complete all as specified and direcrted.

S & F in repairs for vitreous china, squatting pan of 'Orissa' pattern, size 580 mm x 440 mm, white, with 'P' of 'S' Trap, front or back inlet and integral foot rests any pattern, including provision of lime concrete bedding, 10 litres capacity PVC low level flushing cistern, all internal fittings, inlet, outlet pipe connections etc complete all as specified and as directed.

S&F in repairs vitreous china wash hand basin pedestal type, white, 550x 400mm flat back including providing CI brackets, PVC waste pipe 32mm dia, CP brass waste coupling 32mm dia etc, 15mm bore CP fancy type pillar tap all as specified and directed.

S & F stainless steel grating doom 125mm dia complete all as specified.

S&F in repairs Chromium Plated Toilet Paper Holder complete all as specified and as directed

S & F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf corner type three tyres with chromium plated brackets, bracket guard and railing 30cm size incl screws, fixed as in repair complete all as specified and directed.

S&F in repair 125mm chromium plated shower roses with shower arm with or without swivel joints, any size including fixing to uPVC/Steel pipe complete all as specified and as directed.

S&F in repairs Hand shower (health faucet) (ABS Chromium plated) with 8mm dia, 1.2mtr long flexible tube and wall hook complete all as specified and as directed. Make: Jaguar,Cera or Equivalent in specified makes and as approved.

S&F in repairs Chromium plated Jet Spray with CP connection pipe for EWC 15mm bore with fittings complete all as specified and directed. Make Jaguar/Cera or Equivalent in specified makes and as approved.

S&F 15mm dia bore, two way bib tap, long body, fancy type, brass chromium plated, with crutch handle, screwed down for uPVC/iron Pipe complete all as specified and directed.

S&F in repair sinks made of stainless steel 1mm thick kitchen with plugs, washers and waste coupling; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm including waste pipe complete complete all as specified and as directed.

S&F in repairs Brass CP mixer including connection pipes for mixing hot or cold water screwed down for uPVC/iron pipe and fixed complete all as specified and as directed.

M&L for 100mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed.

S&F in repairs Bib taps fancy type chromium plated for 15mm bore pipe, screwed for iron pipes or for brass ferrule all complete as specified and as directed.

S&F in repair fancy type, chromium plated angular stop cock fixed with wall flange for 15mm bore of pipe complete all as specified and as directed.

S&F in repairs brass chromium plated tubular towel rail 20mm dia including brackets both side complete complete all as specified and as directed.

S&F brass chromium plated bracket for towel rail complete all as specified and as directed.

S & F in repairs soap dish chromium plated of size 100 x 100 mm any type fixed with chromium plated brass screws complete all as specified.

S&F factory made 50mm thick 900 x 600mm manhole cover with additional frame for fixing, of precast RCC 1:2:4 type B1 (using 20mm graded stone aggregate) finished the surface even and fair including reinforcement as per manufacturer's design and set in CM 1:4 and handles including demolition of old existing RCC cover (Reinforcement required to cut as facilitate to domolition) of any description and in any position complete all as specified and directed.

Cutting into existing manholes for connecting new drains internal dia of pipe 200mm making good to pipe & to or finished and reforming benching as required. 3/4 section in cement concrete (1:2:4) type B-1, smooth cutting out existing benching for forming branch channel (1/2) rendering complete all as specified and as directed.

M&L for provided reinforced cement concrete pipe 150mm bore class NP-2 with collars laid and jointed with cement all as specifed and directed .

M&L for concrete bed to drain pipes including pipes under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:4:8 type D-2 for 150mm dia pipe complete all as specified and directed.

M&L for cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in surface channels and drains including necessary form work for sauccer drain complete all as specified and directed.

Extra for forming fair finished drain or channel 45cm inner girth in cement concrete, using extra cement, incl forms, moulds, mitred /stopped ends etc complete all as specified and directed.

S&Fin repairs PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to wall of size 110mm bore complete all as specified and directed.

S&F PVC (SWR) pipes, single socketed in any length with rubber ring joints, laid in trenches or in floor of 75mm bore complete all as specified and directed.

S&F in repairs PVC (SWR) pipes, single socketed in any length with rubber ring joints, joints fixed to wall of 75mm bore complete all as specified and directed.

S&F in repair for Stack clamps for bore (any dia) of pipe out of 50 mm by 5 mm flat iron and 16mm dia round iron stays,100mm including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.

S&F PVC (SWR) junction, (Single Tee) equal or unequal 110mm bore complete all as specified and directed.

S&F PVC (SWR) junction, (Single Tee) equal or unequal 75mm bore complete all as specified and directed.

S&F PVC (SWR) bends any radius 110 mm bore complete all as specified and directed.

S&F PVC (SWR) bends any radius 75 mm bore with trap door complete all as specified and directed.

S & F PVC (SWR) vent cowl 110mm Bore complete all as specified and directed.

S & F PVC (SWR) vent cowl 75mm Bore complete all as specified and directed.

S&F PVC (SWR) gully traps 125/100 setting and jointed in cement solvent. complete all as specified and directed.

M&L for rolled mild steel roof trusses ( framed),trussed,purlin crane,gantries,rails and fastening,and heavy framing( beam,tee,anglechannel or flat sections) including distance pieces,cleats etc( Fe 410 w Gde -E 250 quality-A) complete all as specified and directed.

S&F pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering/clading to wall, fixed with self tapping screws complete all as specified and directed.

S&F pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in ridges, roof covering/clading to wall, fixed with self tapping screws complete all as specified and directed.

S&F steel work in tubular /square/rectangular trusses ,cantileve,purlin staging including special shaped washer etc. complete using ERW or induction butt welded tubes confrming to IS 1161-1979 grade St-240 complete all as specified and directed.

Dismentling of mild steel work of as in gates,door,fencing post etc but excluding framed truss complete all as specified & directed.

S&F mild steel framed work conforming to Fe-290 (Gde E-165), as in doors or gates of angle or other section with gusset plates,rails,braces,etc. complete drilled for fixing steel sheeting or other covering to be prepare for hanging including either hooks or hinges etc.

Dismantling fencing wire mesh,any type complete all as specified and as directed .

Supply only, chain link fencing of MS galvanized fencing, any size or type as approved complete all as specified and as directed. NOTE:- Dia of wire shall be as directed by EIC. Actual weight shall be measured at site & paid accordingly.

Fixing only chain link fencing including line wires, any mesh , size and type fixed to any type of standards, rails, straining bolts, etc., incliding provision of binding wire complete all as specified and directed Note : Supply only chain link fencing and line wire will be measeured and paid separetly.

S&F mild steel round bars 10mm dia and over cut to length bent to shape required including cranking, bending, spirally for hooking ends stiffeners confirming to FE-410-W ( Gde E 250) quality-A or Fe 290 (Gde E-165) complete all as specified and as directed .

M&L Mild steel flat iron fillets (for securing wire mesh) including all necessary drilling, bolting or riveting etc and similar work conforming to FE-290 Gde E-165complete all as specified and as directed .

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed to other, or screwed both ends, each screwed end to be fitted with washers and hexagonal or square nut length of bolt n exc 5cm long and dia of neck 11 to 15mm complete all as specified and as directed .

M&L for preparation of new steel surfaces of any description, n.exc 10cm in width or girth when unconnected with other painting or when painted in a different tint and applying two coats of synthetic enamel paint over a coat of primer complete all as specified and as directed .

M&L for preparation of new steel surfaces of any description, exc 10cm in width or girth when unconnected with other painting or when painted in a different tint and applying two coats of synthetic enamel paint over a coat of primer complete all as specified and as directed .

Dismantling posts or struts (wood, steel or RCC), any section, including taking out embeded portion from natural ground and making good disturbed ground complete all as specified and directed.

Excavating in post holes (or similar holes) each n.exc 0.50 cum in any type of soil and getting out returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25 cm watering and removing surplus soil n.exc 50m and making good the surface in hard/dense soil complete all as specified and directed.

M & L for PCC 1:3:6 type C2 ( using 40mm graded stone aggregate ) as in foundation filling or mass concrete or simillar work complete all as specified and as directed .

S&F hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts;posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc.,and similar work conforming complete all as specified and as directed .

S&F for Modular kitchen cabinet and wall mounted cabinet comprising of with and including necessary all other fixing arrangement and screws as per requirement at site etc. All cabinet made of 18mm thick glossy/matte finish solid waterproof MDF board and outer side and top side shall be of 18mm thick prelam coloured solid MDF board, for fixing the items fitted in position and complete all as specified and directed by Engr-in-Charge.

S&F 12mm thick glossy/Matte Finish solid waterproof MDF board for kitchen wall cabinet back side and etc. comprising of with and including necessary all other fixing arrangement as per requirement at site. For fixing the items fitted in position to wall minimum screws size 120mm complete all as specified and directed by Engr-in-Charge.

S&F for stainless steel grill pattern Bottle Rack size 8"wide and 20" deep including stainless steel channels of make Hettich,Godrej or Hafale. Dia of stainless steel bar used to make grill pattern shall be minimum 5mm fixing the items fitted in position and complete all as specified and directed by Engr-in-Charge. Make :- Johnson kitchen, Hafele, Godrej interio and Hettich as approved.

S&F for stainless steel grill pattern basket of size 21"x4"x20" deep including stainless steel drawer channels of make :- Hettich, Godrej or Hafale as approved. Dia of stainless steel bar used to make grill pattern shall be minimum 5mm. Fixing the items fitted in position and complete all as specified and directed by Engr-in-Charge.

S&F for stainless steel grill pattern basket of size 21"x6"x20" deep including stainless steel drawer channels of make :- Hettich, Godrej or Hafale as approved. Dia of stainless steel bar used to make grill pattern shall be minimum 5mm. Fixing the items fitted in position and complete all as specified and directed by Engr-in-Charge. Make :- Johnson kitchen, Hafele, Godrej interio and Hettich as approved.

S&F for stainless steel grill pattern basket of size 21"x8"x20" deep including stainless steel drawer channels of make :- Hettich, Godrej or Hafale as approved. Dia of stainless steel bar used to make grill pattern shall be minimum 5mm. Fixing the items fitted in position and complete all as specified and directed by Engr-in-Charge. Make :- Johnson kitchen, Hafele, Godrej interio and Hettich as approved.

S&F for stainless steel perforated cuttlery box of size 21"x4"x20" deep and including stainless steel drawer channels of make :- Hettich, Godrej or Hafale as approved. Thickness of stainless steel sheet be 1mm thick, fixing the items fitted in position and complete all as specified and directed by Engr-in-Charge. Make :- Johnson kitchen, Hafele, Godrej interio and Hettich as approved.

S&F for stainless steel grill pattern Grain Trolley with base of size 21"x24"x20" deep and including stainless steel channels of make :- Hettich, Godrej or Hafale as approved. Dia of stainless steel grill shall be minimum 5mm. Fixing the items fitted in position and complete all as specified and directed by Engr-in-Charge. Make :- Johnson kitchen, Hafele, Godrej interio and Hettich as approved.

S&F for stainless steel grill pattern Plate rack of size 21"x8"x20" deep and including stainless steel channels of make :- Hettich, Godrej or Hafale as approved. Dia of stainless steel grill shall be minimum 5mm. Fixing the items fitted in position and complete all as specified and directed by Engr-in-Charge. Make :- Johnson kitchen, Hafele, Godrej interio and Hettich as approved.

S&F for stainless steel grill pattern Cup and Soucer rack of size 21"x6"x20" deep and including stainless steel channels of make :- Hettich, Godrej or Hafale as approved. Dia of stainless steel grill shall be minimum 5mm. Fixing the items fitted in position and complete all as specified and directed by Engr-in-Charge. Make :- Johnson kitchen, Hafele, Godrej interio and Hettich as approved.

S&F chromium plated auto hinges split box type overlay door mounting option, opening angle 110degree fixed, with screw all as specified and directed by Engr-in-Charge. Make :Kea SCH or Hettich as approved.

S&F 100mm long stainless steel decorative cupboard handles fixed with nuts, screws and washer complete all as specified and directed.

M&L for 304 grade stainless steel frame work for fixing of modular kitchen below kitchen platform including necessary welding, fixing in true level and position as per availability of size below kitchen platform complete all as specified and directed by Engr-in-Charge.

Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc. 15 cm thickness (below or above ground level) and removing from site complete all as specified and directed.

M&L for Hardcore of gauge n exc 63mm, deposited, spread and levelled in layers in not exc 15cm thick water and rammed to a true surface Complete all as specified and directed.

M&L cement concrete type D-2 1:4:8 (40mm graded stone aggregate) as in sub base 75mm thick complete all as specified and directed.

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete coloured, glossy finish paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; Complete all as specified and directed.

S&F for glossy finished chequered cement concrete tiles 30cmx30cmx30mm /20 cm x 20cm x 25 mm (as approved) thick set jointed with grey cement and pigment and pointed in neat cement slurry with and including 15 mm thick screed bed of CM(1:6) in floors complete all as specified and as directed.

M&L for cement concrete 1:2:4 type B-1(using 20mm graded aggregate) in kerb or mud stop rounded or champhered on edge complete all as specified and directed.

EM PORTION Taking down carefully aluminium / copper point wiring complete (light, fan socket & power) including unserviceable fixtures and fittings such as switches ceilimg roses pendents regulators sockets light fittings etc complete removing material for taking credit & making good disturbed wall / floor etc complete all as directed by Engineer-in-Charge

Taking down sub main wiring complete including fitting and fixtures, removing materials for making good disturbed surfaces of walls, floors, roof etc, all as specified and as directed.

Taking down carefully unserviceable DBs any type/size With MCCBs/MCBs//Isolator etc and disconnecting and making good disturbed surfaces complete all as directed.

M&L Point wiring complete with 1.5 sqmm single core PVC insulated and unsheathed cable 1100 volts, FRLS grade with multistranded copper conductor ISI marked drawn through & including heavy duty PVC conduit duly concealed fixed in walls / roofs / floors / ceiling etc. and including provision of 1.5 sqmm stranded copper conductor cable as earth continuity conductor and connected to common earth dolly including concealed modular flush boxes including Modular box , modular cover plates with frame mounting for housing the switches, socket outlets etc, all as specified and directed. NOTE:- Cost of cutting chases and making good the distrubed surfaces to match with existing finish shall deemed to be included in quoted rate. (a) One light point controlled by one way switch.

(b) One light point controlled by Two way switch.

(c) One fan/exhaust fan point controlled by one switch and one regulator.

(d) One bell/buzzer point controlled by one bell push button on independent.

(e) One 3 pin switch socket outlet point 5 Amps on independent board.

(f) One 3 pin switch socket outlet point 5 Amps on same board with other switch.

All as per above item No. 167.00 but with copper conductor cable for one 3 pin socket outlet, 15 amp independent, with cable 2.5 sqmm size.

S & Fix modular switch 1 way 6A, 1 module all as directed.

S & Fix modular switch 2 way 6A, module all as directed.

S & Fix modular switch1 way 16A, 1 module all as directed.

S & Fix modular socket out let 6A 2/3 on combined 2 module all as directed.

S & Fix modular socket out let 6A/16A-2/3 pin combined 2 module all as directed.

S & Fix Ceiling rose surface backlite 65x50mm 3 terminals complete all as directed.

S&Fix fan regulator electronic 2 modular type volts AC 50 HZ,4 step complete all as directed.

S & Fix Bell push modular type SP 6 Amps all as directed.

S & Fix call bell (Ding Dong) 240 V, 50 Hz all as directed.

S & Fix Batten General purpose suitable for single LED Tubelight with integral LED driver, available in single / double side connection suitable for mount LED tube rod 1 x 18 watts including necessary electric connections 3 core 1 sqmm insulated copper wire from ceiling rose to tube light fitting complete all as specifed and directed by Engineer-in-charge.

S & Fix LED Tubelight (single side connection) with very high efficacy suited for installation in existing tubelight luminaire with G13 lamp holders to give glare free light with necessary fixing arrangement etc complete all as specifed and directed by Engineer-in-charge.

S&F LED Tube light fitting 10 watt, 230 volts, sleek and seamless profiled extruded aluminium batten with an efficient diffuser to illuminate work and retail spaces complete with all accessories all as specified & directed by Engr-in-Charge.

Supply and Fix wall light fitting gold finish fixture with cognac hammered glass diffuser suitable for 7.5 W LED filament lamp E27 base including with suitable lamp all as specified & directed by Engr-in-Charge.

Supply and Fix of down light 18 Watts LED elegantly designed sleek surface mounted pressure die-cast aluminium luminaire in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation and independent electronic LED driver all as specified & directed by Engr-in-Charge.

Supply and Fix of PVC/Polycarbonate angle holder including provision of 7 watts LED bulb all as directed.

S & Fix 30 Watts LED new generation energy saving and environmental friendly long life LED building light made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens embedded PC cover having Bottom Opening seperate driver compartment with IP66 protection and impact resistance of IK08 all as directed.

Supply and Fix 25 watts Gate light fitting New generation, post-top, energy saving, environmental friendly, long life aesthetically designed with symmetrical light distribution, spun aluminium landscape luminaire with high power LEDs as light source all as directed.

Taking down the defective ceiling fan / Exhaust fan of any sweep and make after disconnecting electrically & mechanically and examine & carry out the servicing/overhauling the ceiling fan by thoroughly cleaning the bearing, shaft, stator, rotor & applying the lubricant / grease to the bearing including applying one coat of painting, replacing of broken canopy, re-fixing, testing in all respect for smooth running complete all as directed.

Supply and fixing ceiling fans complete with blades, down rods, and accessories, regulator type 230 V, 1200 mm sweep. Five star rated with brushless direct current motor (BLDC) and deposit the old fan to the store complete all as directed.

S&F exhaust fan, AC, single phase, 240 V, 250 mm sweep, PVC body with louvers, including connected with 3 core 1.5 sq mm copper conductor cable from ceiling rose to exhaust fan all as specified and as directed

S&F exhaust fan, AC, single phase, 240 V, 230 mm sweep, 4 blades Steel body with louvers, with making suitable size hole in any type wall, with good finishing including connected with 3 core 1.5 sq mm copper conductor cable from ceiling rose to exhaust fan all as specified and as directed

Taking down the existing unserviceable Geyser and after disconnecting electrically & mechanically and examine & carry out the servicing/overhauling the geyser by thoroughly cleaning the tank, thermostat, heatingelement and LED Lamp indicator, testing in all respect for smooth running and refixing complete all as directed.

Supply and fix electric water heater, storage type with heating element of 2 KW capacity 25 litre, BEE 5 Star rated, with temperature control knob and analogue temperature indicator complete with all accessories such as safety valve, thermostate, NRV, connection piece etc deposit the old unserviceable geyser to the store all as directed by Engr-in-charge.

S&Fix MCB DB VTPN 4 ways,with metal double door ,IP -43 protection suitable for MCCB as incommer and MCB as out going,VTPN DB's 415 volt 3 phase complete with appropriate size copper bus bar and neutral link as required at site and including cutting chases to wall for fixing of DB and making good distrubed wall/surface all as required at site i.e directed by Engr-in charge.

S & Fix sheet metal enclosure distribution board SPN, 8 ways 240 volts, with 200 amps rated bus bar, with IP 43 protection and double door, suitable for mounting MCBs including taking down old MCB DB complete all as directed..

S & Fix sheet metal enclosure distribution board SPN, 2 way 240 volts, single door, suitable for mounting MCBs all as specified and as directed including taking down old MCB DB complete all as directed.

Supply and fixing MCCB Four pole, 415 volts, 63 Ampere, rupturing capacity 16 KA, in the DB complete all as specified and directed.

S & Fix of RCCB single pole and neutral, 240 volts, 30 mA, 40 Ampere, rupturing capacity complete all as specified and directed.

S & Fix of MCB single pole, 240 volts, 6 to 40 Ampere, rupturing capacity 10 KA, ‘C’ series complete all as specified and directed.

S & Fix Metal plug and socket DB's with MCB 20A SP for AC complete all as directed..

M & L for submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable , multistranded on the surface through and including suitable size of PVC conduit on walls/roofs/ceiling with its accessories all as specified and directed by Engr-in -charge for the following:- (a) 2x1.5 sq mm and 1x1.5 sq mm as earth wire

(b) 2x4.0 sq mm and 1x4 sq mm as earth wire

(c) 2x6.0 sq mm and 1x6 sq mm as earth wire

Taking down the existing electric meter of Single / Three Phase any capacity and make after disconnecting electrically and carry out the cleaning and refixing, reconnecting including applying one coat of paint on existing ms box of electric meter testing in all respect fo smooth running complete all as directed by Engr -in charge.

Supply and Fix 8 W Bollard LED light New generation, energy saving, environmental friendly, long life aesthetically designed aluminium landscape luminaire for diffused lighting with high power LED as light source including excavation, PCC foundation and suitable water proof junction box for connecting the lights complete all as directed.

S & Fix outdoor type FRP junction box light weight suitable for pole mounting inclduing MCB SP 6 Amps single pole, flat iron clamp duly painted with two coats of aluminium paint over a coat of red oxide primer and GI nut, bolts, washers and necessary connector for loop in loop out cable connection and suitable size galnds, of size 200 x 140 x 95 mm complete all as directed.

Supply & lay LT UG cable XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area of the following:- (a) 4 Core 25 Sqmm

(b) 2 Core 6 Sqmm

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m wide and not exceeding 1.5 m depth and getting out soft / loose soil for laying cables / pipes / erection of poles etc. complete all as directed.

Removing excavated material (soil) not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as directed.

Returning filling in soil including spreading levelling watering well ramming in layers not exceeding 25 cm each complete all as directed.

Supply & Laying 50 mm outside dia double wall corrugated pipe (DWC) ISI Mark for enclosing cable below ground / road surface, to a required depth, including suitable size coplers for jointing of pipe all as per site requirement complete all as directed.

M & L Earthing complete with galvanised steel earth plate electrode 60x60cmx06mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion complete all as directed. NOTE:- Cost of earth lead & protection pipe upto 7.5 M shall deemed to be included in quoted rate.

Bharekar Construction

SUN Enterprises

M/S P D TUPE

Samyak Engineers

sagar construction

S G Enterprises