SPL REPAIR TO BLDG NO P 51 JCOS MESS AND PROVISION OF 02 X GARBAGE BINS COVERED WITH WIRE MESH AND GATE AT JALIPA MIL STATION UNDER GE ARMY BARMER

Amount

Taking down cement plaster of any description, any thickness from surfaces of walls/soffits of roof projections & chajjas /ceilings etc. incl raking out joints, hacking for keys, scrubbibg down with water etc complete all as specified and directed.

M&L for rendering 15mm thick in CM (1:6) on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing surfaces, trowelled to even and fair finish without using extra cement complete all as specified and directed.

M&L for 2.0mm thick wall care putty on wall complete all as specified and directed.

M&L for preparing new plastered or unplastered surfaces of walls, and applying two coats of oil emulsion distempering over a coat of interior wall primer complete all as specified and directed.

M&L for preparing new plastered or unplastered surfaces of walls, and applying three coats of white wash complete all as specified and directed.

M&L for complete removal of existing treatment, plastered or unplastered old surfaces of walls, including filling of cracks/holes by crack filler, removing unnecessary nails applying two coats of oil bound distemper/ emulsion over a coat of interior wall primer over 2mm thick wall care putty complete all as specified and directed.

M&L for complete removal of existing treatment, plastered or unplastered old surfaces of walls, including filling of cracks/holes by crack filler, removing unnecessary nails and applying three coats of white wash complete all as specified and directed.

M&L for rendering 5mm thick in CM (1:3) as on concrete surfaces in ceiling finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparing new plastered or unplastered surfaces of ceiling, and applying three coats of white wash complete all as specified and directed.

M&L for complete removal of existing treatment, plastered or unplastered old surfaces of ceiling, including filling of cracks by crack filler, removing unnecessary nails and applying three coats of white wash complete all as specified and directed.

M&L for rendering 15mm thick in CM (1:4) with using WPC on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing surfaces, finished even and smooth without using extra cement complete all as specified and directed. Note : WPC shall be measured and paid separatley.

M&L for preparation of new plastered surfaces of walls and applying two coat of cement based paint over a coat of external primer complete all as specified and directed.

M&L for Complete removal of existing treatment surfaces of walls and applying two coats cement based paint over a coat of external primer complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for Providing, cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, roof, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded for chamfered angles and throating, as directing complete all as specified and directed .

M&L for applying neat cement slurry with 3 kg of cement per sqm with mixing of liquid water proofing compound as per manufacturer instructions over surfaces roof, terrace, projection, chajjas, walls after prepration and cleaning of surfaces complete all as specified and directed.

M&L for rendering 10mm thick cement plaster in CM (1:3) on concrete surfaces of roof, terrace, projection, chajjas, walls (old or new), finished even and smooth (without using extra lime or cement) with mixing of WPC as per manufacturer instructions complete all as specified and directed. (Note : WPC shall be measured and paid separately)

M&L for Applying evenly a priming coat with bituminous primer at 4 Kg per 10 sq metre over plastered/concrete surfaces including prepration complete all as specified and directed.

M&L for laying of APP based polymeric membrane minimum weight 3Kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt not less than 150gm/sqm) by torched application method laid over and including applying evenly a tack coat of industrial bitumen S-35 grade (30/40) at the rate of 1.2 kg per Sq.m including cleaning surfaces by on and as per manufacturer instructions complete and all as specified and directed.

M&L for 40mm thick cement concrete type B-0, 1:2:4 (12.5mm graded aggregate) over roof, terrace in concrete including using integral WPC as per manufacturer's instructions, well compacted and fair finish, with forming by cutting 10mm wide and 10mm deep "V" grooves, cleaning out and filling solidly with a hot mixture, mastic bitumen, size of panel with groove shall not exceeding 0.40 sqm complete all as specified and directed.

Supply only integral liquid water proofing compound complete all as specified and directed.

Demolition of stone slabs and tiles laid, bedded and pointed in any mortar of any description or thickness in floors, aprons etc complete all as specified and directed.

M&L for Glazed ceramic tiles of size 450mm x 300mm x 7mm thick (coloured) of superior quality fixed on vertical surfaces such as skirting/dado etc, set and jointed in neat cement slurry over 10mm thick backing coat in CM (1:4) and pointed in coloured cement to match complete all as specified and directed.

M&L for non skid ceramic tiles of size 7 to 8mm thick (coloured) (Square/rectangular) area of each tile exc 0.06 but n exc 0.11 sqm, in floors, set & jointed in neat cement slurry and pointed in coloured cement over 15mm thick screed bed in CM (1:4) complete all as specified and directed.

M&L for non skid ceramic tiles of size 7 to 8mm thick (coloured) (Square/rectangular) area of each tile exc 0.18 but n exc 0.38 sqm, in floors, set & jointed in neat cement slurry and pointed in coloured cement over 15mm thick screed bed in CM (1:4) complete all as specified and directed.

All as per Sl item No 25 above but in skirting over 10mm thick backing coat in CM (1:4) complete all as specified and directed.

M&L for 30mm thick PCC 1:2:4 Type B1 with 20mm graded stone aggregate as in levelling course in floor complete all as specified and directed.

M&L for Kota stone slab 20-25mm thick (in single piece as vertical support and horizointal base for granite top) in cooking platform, jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete complete all as specified and directed.

M&L for Machine cut kota stone slab flooring 20-25mm thick over and including screed base 15mm thick in CM (1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab inclunding rubbing and polishing complete all as specified and directed.

M&L for Kota stone slab 20-25mm thick (in single piece) in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab inclunding rubbing and polishing including backing coat 10mm thick in CM (1:4) complete all as specified and directed.

M&L for 20mm thick Granite (of any type in single piece) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified.

Demolition of wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards / slabs / blankets, any thickness, including cover fillets complete all as specified and directed.

M&L for Providing and fixing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions including GI frame work for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel at 457mm centre to centre, fixed on slab complete all as specified and directed.

M&L for preparing new plastered or unplastered surfaces of ceiling, and applying two coats of distemper oil emulsion over a coat of interior primer over 3mm thick wall care putty complete all as specified and directed.

Dismantling of boarding any description fixed in any position with nails complete all as specified and directed

S&F for 18mm thick MDF prelaminated board, prelaminated one side with decorative choice lamination matt finish & other side balancing white lamination fixed with screws as in cupboard shutters with self closing hinges 02 Nos in each shutter and fancy SS handles 01 No 100mm size in each shutter and drawer of bed room, kitchen and internal shelves, kitchen cabinets, partitions and drawers of any size complete all as specified and directed .

S&F for kitchen baskets 100 % stainless steel, non - magnetic, multilayer chrome plated, argon welded, double sealed ball bearing mechanism capable of holding plates, cup, saucers, bowls and dongas with 470x485x200 mm of carcass including moving drawer channels complete all as specified & directed . Make : Prod code No. 5904 of Godrej or techno commercially equivalent make in Hettich/Lifetime ISI marked

S&F for kitchen baskets 100 % stainless steel, non - magnetic, multilayer chrome plated, argon welded, double sealed ball bearing mechanism capable of holding plates, cup, saucers, bowls and dongas with 470x485x150 mm of carcass including moving drawer channels complete all as specified & directed . Make : Prod code No. 5903 of Godrej or techno commercially equivalent make in Hettich/Lifetime

S&F for Cup and Saucer Basket 100 % stainless stee , non - magnatic, multilayer chrome plated, argon welded, double sealed ball bearing mechanism capable of holding plates, cup, saucers, bowls and dongas with 420x485x100 mm of carcass including moving drawer channels complete all as specified & directed . Make : Prod code No. 6130 of Godrej or techno commercially equivalent make in Hettich/Lifetime

S&F for Perforated Cutlery Basket 100 % stainless steel, non - magnatic, multilayer chrome plated, argon welded, double sealed ball bearing mechanism capable of holding plates, cup, saucers, bowls and dongas with 420x485x100 mm of carcass including moving drawer channels complete all as specified & directed . Make : Prod code No. 6133 of Godrej or techno commercially equivalent make in Hettich/Lifetime

S&F for Thali-Plate Basket 100 % stainless steel, non - magnatic, multilayer chrome plated, argon welded, double sealed ball bearing mechanism capable of holding plates, cup, saucers, bowls and dongas with 420x485x200 mm of carcass including moving drawer channels complete all as specified & directed. Make : Prod code No. 6138 of Godrej or techno commercially equivalent make in Hettich/Lifetime

S&F in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers, waste pipe and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets or stone slab and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

Taking down shutters of any description exc 1 sq.m and n exc 2 sqm each complete all as specified.

Taking down shutters of any description exc 1 Sqm and n exc 2 Sqm each and refixing in same opening after cutting by chishel or hand saw, peeling by plane, fixing/ re-placing of hinges, repairing etc including all nales screws, pieces, small let in for making good where hinges, etc. have been removed from chowkhats or frames, for the replacing of frame if required, shutters, etc. including painting or oiling to match, if required complete all as specified and directed. (Note : Hinges shall be measured and paid separately)

Taking down chowkhats or frames (without taking off shutters from the frame) n. exc 1.5 Sqm complete all as specified and directed.

S&F for 35mm thick 2nd class HW plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F for 2nd class H.W. glazed & skeleton shutter 35mm thick factory made open rebated & prepared to receive glass gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass,gauge etc size of members of shutter as specified in SSR part-I , section 8, clause 8.24 (a) complete all as specified and directed.

M&L for preparation of New or previously untreated wood and wood based surfaces of any description over 10cm in girth or width and painting with two coats of synthetic enamel paint over a coat of primer complete all as specified and directed.

M&L for preparation of old painted wood and wood based surfaces of any description over 10cm in girth or width and painting with two coats of synthetic enamel paint complete all as specified and directed.

S&F for stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire stapples complete all as specified and directed.

S&F in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire stapples, wooden doors, steel windows, Aluminium windows including removing of wooden beading, flat iron, alm cleats etc and refixing of the same, if beading, iron flat or alm cleat if found broken during replacement of wire mesh the same will be replaced with new, complete all as specified and directed.

S&F for PVC door frames of sizes 50 x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS Square tube in opening of suitable size complete all as specified and directed.

S&F for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. complete all as specified and directed.

M&L for cement concrete (1:4:8) type D2 using 40mm graded stone aggregate in foundations, filling and mass concrete complete all as specified and directed.

M&L for 75 mm thick cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregate) as in plinth protection including making joint at every 2.5mtr interval and at corner and filled with mixture of bitumen and sand and finished even and fair and laid in alternate bays complete all as specified and directed.

S&F for 100mm long butt hinges medium weight cold rolled mild steel complete all as specified and directed.

S&F for aluminium floor door stoppers double legged length 140mm with hard drawn steel spring fitted in floor complete all as specified and directed.

S&F for 150mm long Aluminium anodizes barrel tower bolts of extruded section complete all as specified and directed.

S&F 150 mm size aluminium anodized handle complete all as specified and directed.

M&L for 300mm long aluminium alloy anodized sliding door bolts with Hasp and staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F mild steel ordinary rat tail rod pattern spring 300mm size including roller & roller plate and incl welding complete all as specified and directed.

S&F in repair 25mm dia fancy stainless steel curtain rod with fancy fixing brackets, fancy stops/supports, rollers etc. complete all as specified.

S&F in rep vitreous china wash down water closet pan (pedestal pattern), white including connection to drain (or outgoing pipe) and to flushing pipe with and including flush pipe and plastic water closet seat, white closed pattern with flat bottom, cover and mild steel hinges device complete all as specified and directed.

S&F in repair PVC valveless flushing cistern, low level white with inlet ball valve float and handle including brackets complete fixed capacity of flush 10 ltrs complete all as specified and directed.

S&F in repairs wash hand basins, vitreous china,of size 560x400x205mm (oval shape counter type) including cutting for and pinning in stone slab if required or erecting on stone slab stand inclusive of fixing of supply and including waste pipe etc complete all as specified and directed.

S&F in repairs CP wall mixer for mixing (HOT/COLD) bathroom water, with wall cap of CP Brass, screwed down, screwd for iron pipes 15mm bore complete all as specified and directed.

S&F in repairs 15mm bore pillar taps long body, cast copper alloy with capstan heads, chromium plated, fancy type screwed down high pressure with or without lettered “HOT” or “COLD” with long screwed shanks and fly nuts complete all as specified and directed.

S&F in repair brass CP wash hand basin mixer fancy type single lever without poput waste system with 450mm long braided hoses with necessary fixing arrangements complete all as specified and directed. Make : Model No. FLR-5001B of JAQUAR make or techno commercially equivalent model in Kolher/ Grohe.

S&F in repair brass CP sink mixer fancy type with regular spout with necessary fixing arrangements complete all as specified and directed. Make : Cat No. 7655 of Prayag or techno commercially equivalent model in Cera/ Jhonson/Hindware.

S&F in repair 15mm bore Bib taps CP fancy type, cast copper, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repair 15mm bore, 450mm long, PVC connections with brass unions internally threaded both ends complete fixed to iron pipe at both ends as fixed in repairs complete all as specified and directed.

S&F in repair CP fancy type stop valves ,cast copper alloy, screwed both ends for iron pipe or for union of 15mm bore complete all as specified and directed.

S&F in repairs 15mm bore stop valves ,cast copper alloy, chromium plated with long shank and cup (concealed type) complete all as specified and directed.

S&F in repair 1.0m length Hand faucet MS chromium plated with hanging device fixed complete all as specified and directed.

S&F in repair 1.0m length Jet water spray including MS chromium plated hanging device complete all as specified and directed.

Dismantling of water tanks of capacity 1000 ltrs (RCC hume Pipe/PVC) including disconnecting all connections etc. complete all as specified and directed.

S&F for new rotational moulded polythylene water storage tank of capacity 1000 ltrs (cylindrical/vertical with closte top) hoisted and fixed in position all as specified in SSR Part-I including providing and fixing brass ball valve high pressure with polythene float and fly nut, 20mm bore complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified and directed.

Taking up or down 20mm bore steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified and directed.

Taking up or down 25mm bore steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified and directed.

S&F for 16mm bore of CPVC of food grade pipes SDR 11 and plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

S&F for 20mm bore GI tubing medium grade with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

S&F for 25mm bore GI tubing medium grade with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

S&F in repair 20mm bore Gun metal gate valves with iron wheel head screwed both ends for iron pipes complete all as specified and directed.

S&F in repair 25mm bore Gun metal gate valves with iron wheel head screwed both ends for iron pipes complete all as specified and directed.

S&F in repair Brass chromium plated shower rose 125mm size complete all as specified and directed.

S&F in repair brass chromium plated Tubular towel rail 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

S&F in repair for 75mm bore of PVC (SWR) pipes single socketed in any length with rubber ring joints laid on wall complete all as specified and directed.

S&F in repair for 110mm bore of PVC (SWR) pipes single socketed in any length with rubber ring joints laid on wall complete all as specified and directed.

S&F for 75mm bore PVC (SWR) bend any radius complete all as specified and directed.

S&F for 110mm bore PVC (SWR) bend any radius complete all as specified and directed.

S&F for 75mm bore PVC (SWR) junction single, (Single T) equal or unequal with access door complete all as specified and directed.

S&F in repair stainless steel soap dish, approximate size 130x120x30mm complete all as specified and directed.

S&F in repair Toilet paper holder with flat recessed type stainless steel complete all as specified and directed.

S&F in repair sheet glass corner wall mounted shelf assembly consisting of 5.5mm thick sheet glass 220mmX220mm size with chromium plated bracket guard and railing 50mm high complete all as specified and directed.

S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

Cutting chases in stone, concrete block or slab walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth all as specified and directed.

Dismantling wrought iron or mild steel work of any description, complete all as specified and directed.

S&F for MS framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed.

M&L for preparation of New or previously untreated steel or iron surfaces of any description over 10cm in girth or width and painting with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Demolition of cement concrete (reinforced) in roofs, floors (other than ground floors), beams staircases, landing, chajjas, and similar suspended work complete all as specified and directed.

M & L for RCC (nominal mix) Type B1 1:2:4 (20 mm graded aggregate) in chajjas complete all as specified and directed.

Formwork to chullah hoods, chajjas, troughs and similar items including edges, flat rough finished surfaces of concrete complete all as specified and directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

All as per Srl item No 107 above but 6mm to 8mm dia complete all as specified and directed.

Demolition of brickwork or stone, PCC block, boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stone work and precast concrete articles complete all as specified and directed.

M&L for walling of random rubble uncoursed ,well bonded ,bedded and solidly hearted built in CM (1:4) and brought up to course complete all as specified and directed.

All as per Srl item No 110 above but except stone complete all as specified and directed.

Extra over lime or sand stone, stone walling for hammer dressing to face stones and dressing or face beds and joints, with maximum depression on face from straight edge held against the dressed surface n exc. 20mm, as specified, of random rubble walling, uncoursed or brought upto courses complete all as specified and directed.

Dismantling of timber scantlings framed work in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section complete all as specified and directed.

M&L second class hard wood clean swan, timber fixed in scantling of unframe roof work all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in concrete bed to 150mm bore drain pipes including packing under & haunching against the sides of pipes after they are laid & tested for 150mm bore pipe including demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement concrete mortar complete all as specified and directed.

M&L for Reinforced concrete pipes 150mm bore class NP-2, laid and jointed complete with collars, complete all as specified and directed.

M&L for precast cement concrete 1:2:4 type B-1 using (20mm aggreates) set in CM (1:4) as in cover slabs (for manhole etc) & simillar articles with plain faces complete (Reinforcement will be measured and paid separately) all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out hard/dense soil complete all as specified and directed.

Returning, filling in including spreading, levelling, watering & well ramming in layers n.exc 25cm complete all as specified and directed.

M&L for Machine pressed precast concrete interlocking paver block rubber moulded any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade over 25mm thick sand cushioning complete all as specified and directed.

M&L for Chipping of 50mm average thickness unsound/weak concrete material from slabs, beams, columns, footings etc. and plaster with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts complete all as specified and directed.

M&L for Cleaning & applying rust remover on (CICO Clean-o rust) in two coats over rusted reinforcement surface of RCC members and providing anti corrosive coating with two component epoxy based zinc rich primer/Rust passivation Inhibitor coat at the rate of 2-3 sq. mtr/ltr not less than 50 microns dft with CICO ZINCILATE-500 or equivalent to reinforcement surface as per manufacturer’s instructions including all machinery, tools tackles and clearing of debris. Make: CICO Technologies Ltd, M/s Sika India Pvt Ltd, M/s Bostik India Pvt Ltd, M/s Choksey chemicals Pvt Ltd, M/s Thermax Ltd, M/s Master builder solution (BASF) or techno commercially equivalent . (Note : Entire Exposed Surface of RCC members after chipping shall be measured and paid.)

S&F of new steel or rebars by drilling holes with 10 mm to 25mm dia and 100 to 200mm deep/wide as per IS code of 10D formula and filling the holes after inserting of reinforcement dia 8 to 16mm for anchoring at ends/shear connector and filled the holes with one or two component styrene free vinylester resin anchor or two components, styrene & cement free epoxy- acrylate fixing and anchoring compound ( having the technical parameters mentioned in material specifications) using standard sealant applicator gun after drilling holes of required diameter at required locations, for holding / fixing / placing in position the steel mesh reinforcement at desired level/ stretching. (Note : Steel/reinforcement shall be paid and measured separately) . Make: CICO Technologies Ltd, M/s Sika India Pvt Ltd, M/s Bostik India Pvt Ltd, M/s Choksey chemicals Pvt Ltd, M/s Thermax Ltd, M/s Master builder solution (BASF) or techno commercially equivalent

M&L for providing Micro concrete M-50 (Minimum grade) with CICO MICROCRETE at the rate of 25kg per 0.0125 m3 with 20% properly graded 5mm to 10mm silt free aggregate as per manufacturer instructions and mixing concrete with mechanically electrically operated mixer machine, compaction with proper vibrator, including all necessary scafolding if required etc all as specified and directed. Make: CICO Technologies Ltd, M/s Sika India Pvt Ltd, M/s Bostik India Pvt Ltd, M/s Choksey chemicals Pvt Ltd, M/s Thermax Ltd, M/s Master builder solution (BASF) or techno commercially equivalent . (Note : Rates for the drilling of holes of floor slab/ columns/ Beams or Junction or RCC beam, column and floor slab for column and beams main bars of any dia including filled the same holes with one or two component styrene free vinylester resin anchor or two components, styrene & cement free epoxy- acrylate fixing and anchoring compound shall be deemed to be included in quoted rates.)

M&L for Epoxy Bonding Agent suitable for bonding new to old concrete, bricks and steel components, bricks, tiles etc after the prepration of old concrete/RCC surface by cleaning and removing of dust, dirt, loose particles, laitance etc by wire brushing, scrapping and washing with water complete all as per manufacturer's instructions. Make: CICO Technologies Ltd, M/s Sika India Pvt Ltd, M/s Bostik India Pvt Ltd, M/s Choksey chemicals Pvt Ltd, M/s Thermax Ltd, M/s Master builder solution (BASF) or techno commercially equivalent

M&L for injection grouting for the RCC members like column, beam, slab etc with the mixture of fine sand and cement with appropriate pressure and machinery, ratio of material is (1:1) or directed by Engineer-in-charge for the repairing of cracks, holes, voids, honeycombing, damage of structural member etc, drill the ports or holes, distance between two nozzles/nipples approx 0.50m in RCC member, having dia 2.5cm and 5.0cm deep and fix the nozzle/nipple of the grouting machine/hose pipe, filled the properly cracks and holes of structural member, all around or surface area of RCC member with epoxy, polyster or cementious materials give time to seal to be hardened, inject the grout material in the RCC member till RCC member voids saturated completely, for the same process to be repeated 02 or 03 times after some interval, refix the nipples properly without damazing the RCC members and holes of the same filled properly with non shrinkage material of min M-50 grade, complete all as specified and directed. Note : Rates of the all requires machinery, tools etc for the injection grouting shall be deemed to be included in quotated rates.

M&L for Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified & directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil complete all as specified & directed.

M&L for broken stone or boulders hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified & directed.

Removing excavated soil n exc. 50m & depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified & directed.

M&L Pre-cast cement concrete block type C-1 (1:3:6) in CM 1:6 masonry with solid blocks exc.10 cm in width and setting in mortar complete all as specified & directed.

M&L 25mm damp proof course type B-0 (1:2:4) to horizontal or vertical surfaces including necessary formwork complete all as specified & directed.

M&L 100mm thick PCC type B-2, (1:4:8) using 40mm graded stone aggregate complete all as specified & directed.

M&L rendering 10mm thick on fair faces of brick work or concrete surfaces in CM 1:6 complete all as specified & directed.

M&L for Plastering 15mm thick in CM (1:6) s on stone wall surface finishing the surface even & smooth with out using extra cement complete all as specified & directed.

M&L for Preparation of new plastered surfaces of wall and applying two coats of white wash complete all as specified & directed.

S&F Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 for portions framed and hung as gates, including pintle hinges, stops,hand-made sliding bolts, etc complete all as specified & directed.

S&F 4mm dia galvanised steel wire, 150x100mm mesh, made up into mattresses or cages, lapped, wired and laid in position, including closing after filling complete all as specified & directed.

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long (Diameter of neck is between16 to 20mm) complete all as specified & directed.

M&L 25mm thick Cement concrete type B-0, 1:2:4 (12.50 mm graded aggregate) as in coping complete all as specified & directed.

Cutting holes in n brick walls built in cement mortar or cement lime mortar and stone walls built in lime mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified & directed.

M&L for 100mm thick cement concrete type type C-2, 1:3:6 (40mm gradedaggregate) as in plinth protection complete all as specified & directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

Taking down unserviceable main switch/DB, Teak wood boards etc complete all as specified and directed.

Taking down submain wiring of any size complete all as specified and directed.

M&L for point wiring in (concealed/surface as per site conditions) with PVC insulated, unsheathed, single core multistandard copper conductor cable( FRLS) of size 1.5 Sqmm, 1100 volts grade including 1.5 Sqmm PVC insulated, unsheathed, copper conductor cable for earth continuity wire to be drawn through in and including PVC conduit medium grade ISI marked with its acessories including necessary pressed steel terminal boxes flushed in wall and 3 mm thick ISI marked laminated sheet cover and SS screws with cup washers for fixing switches, sockets, fan regulators etc. including all necessary wall cutting chases and making good disturbed surfaces in cement mortar 1:3 for one light /fan/CB point controlled by one switch, complete all as specified and directed.

All as per Srl item No 147 above but for one 3/2 Pin 5 Amp socket out let point on the independent board.

All as per Srl item No 147 above but for one socket outlet 3/2 pin, 5 Amp, point on the same board with other switches.

All as per Srl item No 147 above but with cable 2.5 sqmm including 2.5 sqmm cable as earth wire for 15/16 amp socket point.

All as per Srl item No 147 above but with cable 4 sqmm including 4 sqmm cable as earth wire for 15/16 amp socket point.

Supply and fix single pole and neutral enclosures with a two pin and earth plug and socket complete with one double pole MCB 10 A ,240 V complete all as specified and directed.

Supply and fix switch piano flush type single pole one way 5 Amps complete all as specified and directed

Supply and fix socket outlet 2in1, 3pin,5A complete all as specified and directed.

Supply and fix socket outlet 2in1, 3pin,6/16 A complete all as specified and directed.

Supply and fix switch piano flush type single pole one way 15 Amps complete all as specified and directed.

Supply and fix ceiling rose surface bakelite 65x50 mm two to three terminals complete all as specified and directed.

Supply and fix bell push, flush type, 5 Amps complete all as specified and directed.

Supply and fix call bell AC, 230 volts single pole complete all as specified and directed.

Supply and fix dimmer type electronic fan regulator flush type, 230 volt, AC complete all as specified and directed.

S&F Supply and fixing single pole 06 to 32 A rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) in the MCB DB complete with connection testing and commissioning complete all as specified and directed

All as per Srl Item No 161above but SPN 32 A rating complete all as specified and directed

All as per Srl Item No 161above but TPN 63 A rating complete all as specified and directed

S&F sheet metal enclosure (for DB's when MCBs to be used), flushed in wall single pole and neutral Double door, 8 way, 240 Volts with PVC MCB blanking plates, stove enamelled, dust and vermin proof suitable for incorporation of MCB's and isolators etc complete all as specified and directed.

S&F MCB, DB double door type, made out of CRCA mild steel sheet flushed in wall, TPN 4 way with 200 Amps rated bus bar , 415 volts IP-43, with PVC MCB blanking plates, stove enamelled, dust and vermin proof suitable for incorporation of MCB's and isolators etc complete all as specified and directed.

Taking down the ceiling fans from the existing location and refixing the same with new down rod of length 1.0 mtr (upto the false ceiling level) and connecting up with copper cable from ceiling rose to fan complete all as specified and directed.

Supply and fix exhaust fan 300 mm sweep with louvre complete fixed to wall with suitable MS bolts, grouted to wall and connecting up including provision of cable from connector to fan with flexible copper conductor cable 24/0.2mm ,Metal exhaust fan and taking down the existing exhaust fan and deposit in MES store complete all as specified and directed.

Supply and fix exhaust fan 250 mm sweep with louvre plastic body complete fixed to window/wall with suitable fastening and connecting up including provision of cable from connector to fan with flexible copper conductor cable 24/0.2mm and taking down the existing exhaust fan and deposit in MES store complete all as specified and directed.

M&L sub main wiring surface type with two runs of single core, PVC insulated, unsheathed multi standard copper conductor cable of size 6 Sqmm, 1100 volts grade (FRLS) and one run of 6 Sqmm PVC insulated multi stranded copper conductor for earth continuity conductor drawn through and including suitable size ISI marked rigid PVC conduit with all necessary accessories such as bends, tees, junction boxes, elbows complete all as specified and directed. (Note :- Two runs of 6 Sqmm cable, one run of 6 Sqmm continuity earth wire and one run of PVC conduit with all necessary accessories will be measured as one length).

M&L sub main wiring surface type/conealed type as required at site with four runs of single core, PVC insulated, unsheathed multi standard copper conductor cable of size 10 Sqmm,1100 volts grade (FRLS) and one run of 10 Sqmm PVC insulated multi stranded copper conductor for earth continuity conductor drawn through and including suitable size ISI marked rigid PVC conduit with all necessary accessories such as bends, tees, junction boxes, elbows complete all as specified and directed. (Note :- Four runs of 10 Sqmm cable, one run of 10 Sqmm continuity earth wire and one run of PVC conduit with all necessary accessories will be measured as one length).

S&F in repair LED 25 Watt street light fitting for bldg secutiry complete with light grade GI brackets, Nuts, bolts, clamps complete with all accessories internaly pre wired and including connecting up with twin core twisted flexible copper conductor cable complete as specified and directed. Make - Crompton/ Havells/ Philips/Bajaj/Wipro.

S&F LED in replacement batten suitble for indoor application 20 W, 4' length , wall mounted with polycarbonate housing, end cap made of ABS plastic of white colour finish and high efficiency translucence (HET) diffuser and integral electronic driver including two point surface mounting on wall/ ceiling and connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed. Make : Havells/Bajaj/Wipro/Crompton

S & F in replacement LED batten suitble for indoor application 10 W, 2' length,wall mounted with polycarbonate housing, end cap made of ABS plastic of white colour finish and high efficiency translucence (HET) diffuser and integral electronic driver including two point surface mounting on wall/ ceiling and connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed . Make : Havells/Bajaj/Wipro/Crompton

S & F in replacement LED light fitting 1X9 W bulkhead luminaires with lamp holders etc complete with all aceessories including connecting up with twin core twisted flexible copper conductor cable complete all as specified and directed .

M & L lamp holder (Angular) PVC/poly carbonate type with back plate suitable for batten fittings complete all as specified and directed .

Supply & fix LED lamp 10W, min lumen output 950 lumens at 6500 K CCT for batten holders complete all as specified and directed.

Supply and fix in replacement recess mounted low glare LED panellight 2'X2' size 36 watt white/warm white for armstrong/grid ceiling or similar ceiling mounting system complete prewired using 1.5 Sqmm FRLS PVC insulated (Unsheathed) 3 core copper conductor cable, 1100V grade complete all as specified and directed. Make: BAJAJ/Wipro/Crompton/Havells

M & L for inverter point wiring for light, ceiling fan and 5 Amp socket with 2.5 sqmm,PVC insulated, unsheathed, single core multistandard copper conductor cable( FRLS), 1100 volts grade including 1.5 Sqmm PVC insulated, unsheathed, copper conductor cable for earth continuity wire to be drawn through in and including PVC conduit medium grade ISI marked with its acessories upto the main DB and 15 A switch socket combination with gang box flushed in wall for inverter power supply complete all as specified and directed.

S&F for wall mounted kitchen pyramid commercial chimney of size 90cm, capacity 1200Cum/hr filterless heat/water auto clean chimney (complete set), motion sensor technology 2 LED lamps, touch control panel with exhaust pipe and all required accessories, installation at site including making of hole in any type of wall and making good after installation complete all as specified and directed. (Make: Elica Model WDFL 906 HAC LTW MS NERO, Touch+Motion Sensor Conrtol, Black or techno commercially Equivalent in Faber, Inalsa, KAFF, Hindware, Glen, Whirpool)

M&L in replacement for earthing complete with GI earth plate Electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth plate not less than 2.25 Metre deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level connected to galvanished earth wire 4.0 mm dia by means of bolts, nuts check and washers of GI or steel all as shown in electrical plate No. 3 of SSR Pt -I connected to earthing test point all as specified or indicated including GI pipe 15 mm dia light grade for earth wire protection, necessary excavation, earth work in any type of soil, PCC chamber and RCC cover slab, connecting lead wire from test point to DB complete all as specified & directed

Lalit and Brothers

AMBEY MAA CONSTRUCTION COMPANY