Construction of School with Residential Building for Backward Classes at Barhate, Sahebganj

Amount

Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50 M. including all lifts, levelling, ramming the foudation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/l.

Extra for earth work in hard soil as per specification and direction of E/I. (vide classification of soil item - B).

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge.

Ordinary rock

Hard rock (blasting prohibited)

Filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50Mand lift of 1.5M all complete as per building specification and direction of E/I. (mode of measurement compacted volume)

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including' cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l (Mode of measurement complacted volume).

Providing designation 75 A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level

1:2:4 (1 Cement: 2 coarse sand(Zone III): 4 graded stone aggregate 20 mm nominal size)

1:3:6 (1 Cement: 3 coarse sand(Zone III): 6 graded stone aggregate 20 mm nominal size)

1:4:8 (1 Cement: 4 coarse sand(Zone III): 8 graded stone aggregate 20 mm nominal size)

Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required centering, shuttering complete. 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size)

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse send : 6 graded stone aggregate 20 mm nominal size ) over 75 mm thick bed of dry brick ballast 40 mm nominal size ,wall rammed and consolidated and grouted with fine sand including necessary excavation, levelling & dressing & finishing the top smooth.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement- All work up to plinth level.

1:1.5:3 (1 cement: 1.5 coarse sand(zone-III): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in wall (any thickness), including attached pilasters, butterses, plinth and string courses, fillets, column, pillars, piers, abutments, posts and struts ets. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement: 1.5 coarse sand(zone-III): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floor, roofs having slope up to 15'' landing, balconies, shelver, chajjas , lintels, bands, plan window sills, staircases and spiral stair case above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement: 1.5 coarse sand(zone-III): 3 graded stone aggregate 20 mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form for :

Foundations, footings, bases of columns etc. for mass concrete.

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Centering and shuttering including strutting, propping etc. and removal of form for Shelves (Cast in situ)

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs,(excluding landings) except spiral-staircasess.

Weather shade,Chajjas, corbels etc. including edges

Suspended floors, roofs, landings, balconies and access platform with water proofply 12 mm thick.

Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured). Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

Providing tor steel reinforcement of 8mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. Taking 8mm TMT FE 500 ( only valid for SAIL & TATA STEEL)

Providing Tor steel reinforcement of 10mm, 12mm & 16mm mm dia. bars as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l.

10mm TMT FE 500 (only valid for SAIL & TATA Steel)

12mm TMT FE 500 (only valid for SAIL & TATA Steel)

16mm TMT FE 500 (only valid for SAIL & TATA Steel)

20mm TMT FE 500 (only valid for SAIL & TATA Steel)

Making 6x6mm grooves in plaster surface over walls truely horizontal or vertical as specified. at regular intervals, at all heights including cleaning, finishing, scaffoding and curing wth all leads and lifts of water all complete as per building specification and direction of E/|

Providing designation 75 A brick work in C.M.(1 :6) in foundation & Plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10 mm thick mortar joints cost of screening materials, scaffolding , raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 100A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9" x 4.5" x 3") in C.M. (1:6) in superstructure with approved quality of clean sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 112mm thick reinforced designation 100A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9" x 4.5" x 3") in C.M. (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, carraige of materials, scaffolding, raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforced) all complete as per building specification direction of E/I.

Extra for brick work for EACH consecutive floor above first floor including watering and scafolding, all complete as per direction of E/l.

Terrace floor

Providing and fixing 18 mm thick gang saw cut mirror polished, machine cut for kitchen platforms, vanity counters facias and fimilar locations of required size of approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand ) with joints treated with white cement , mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble (Area of slab over 0.50 sqm)

Granite of any colour and shade Area of slab over 0.50 sqm

Extra for providing opening of required size & shape for wash basins/kitchen sink in kitchen platform, vanity counters and similar location in marble/stone work including necessary holes for pillar taps etc .including rubbing and polishing of cut edges etc. complete.

Supplying, fitting and fixing 35mm thick solid core type non-decorative single leaf flush door shutter in door & windows with black board core blended with high quality phenol phormal dehydes synthetic resin both side comercial veneered of standard make with oxidised iron fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l

Supplying, fitting and fixing 35mm thick solid core type non-decorative Daboul leaf flush door shutter in door & windows with black board core blended with high quality phenol phormal dehydes synthetic resin both side comercial veneered of standard make with oxidised iron fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l

Providing and fixing PVC rigid foam sheet 1 mm thick on existing door shutters (bathroom and W.C. doors) using synthetic rubber based adhesive.

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured) :

Rectangular or square

Supplying, fitting, and fixing M.S. grill made of 20 x 6mm M.S. flat as per approved design and drawing , properly fabricated with joints continuous fillet welded and finished, carriage of grill to work site, hoisting as per building speficiation and direction of E/I. (where material is not supplied by the deppt.)

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing aluminium hanging floor door stopper, ISI marked,anodised (anodic coating not less than grade AC 10 as per IS : 1868)transparent or dyed to required colour and shade, with necessary screws etc. complete.

Twin rubber stopper

Supplying,fitting and fixing callapsible gate of approved size and make properly fabricated with vertical double channels 20X'10X2 mm. at 100mm. Centres and braced with M.S. flat diagonals 20 X 3mm, with top and bottom rails of T. iron 40x40x6mm with 38 mm dia steel pulleys complete with bolts, nuts, locking arrangements, stoppers, handles, including applying a priming coat of red lead paint, car riage, hoisting and taxes all complete as per building specification arrd direction E/|.

Supplying, fitting and fixing 20 guage GCI sheet gate fitted on M.S> angle frame of size 60X60X6mm including cost of fabrication providing necessary locking arrangement with haskal and domny duly fixed in PCC (1:2;4) blocks of required size applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/I.

S/F/F local make fully glazed steel door, windows or ventilation of standard rolled 'Z' and mullion steel section and size as per IS - 38 joints met welded with 100x16x3mm M.S. lug fixed in cement concrete (1:2:4) blocks 15x10x10 cm. size including the cost of oxidised iron fittings with hinges, handle pre step catch springs, 3mm thick plain glass panes with aluminium beads and inner frame fixed with lugs with 20cm long 6.30mm G.I. counter sunk machine screw nuts and applying a coat of red lead paint carriage to work site hoisting and placing in all position in all storys and taxes all complete as per building specification and direction of E/I.

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: Profile B

Fixing with adjustable lugs with split end tail to each jamb

Steel work in built up tubular trusses including cutting, hoisting, fixing in position and applying a priming coar of approved steel primer, welded and bolted including special shaped washers etc. complete:

Hot finished welded type tubes

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Steel work welded in built-up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required

In gratings, frames, guard bar, ladders, balcony and staircase railings, brackets, gates and similar works

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer

M.S. tube

Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete.

Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides

Providing and fixing bright finished brass helical door spring (superior quality).

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron ‘Y’ shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :

25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Extra for pre finished nosing in treads of steps of Kota stone/ sand

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and laylng Doublecharge vitrrfied floor tiles in diiierent sizes (thickness to be i specrfred by the manufacturer) with water absorption less than 0.08% and conforming to lS 15622 / ISO 13006 of approved make in all colours and shades laid on 20mrn thick cement mortar 1 4 (1 cement:4 coars sand) jointing with grey cement slurry @ 3.3 kg/ sqm including I grouting the joints with white cement and matching pigments etc complete Size of tile 600x600 mm

Providing and laying matt finished vitrified tile of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty as per building direction of E/I.

Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 12mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5with 5% cico or any other approved water proofing compoundincluding taxes and royalty all complete as per building specification and direction of E/l.

Providing 1.5mm cement punning including curing, carriage of water with all leads and lifts as per building speicification and direction of E/I.

Providing two coat of snowcem of approved shade and make over a coat of cement primer on new surface including preparing the plastered surfirce smooth with sand paper, scaffolding, curing and taxes ali complete as per building specifrcation and directron of E/l'

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface inluding preparing the plastered surface by rubbing wmooth with pumice stone or fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per buiiding specification and drrection of E/i.

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade

New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

Providing two coats of synthetic enamel paint of approved shade and make over new wooden surfaces including preparing the surface after cleaning, removing dirt, scales, smokes, grease and sand papering, including cost of scaffolding and taxes, all complete as per building specifications and direction of E/I

Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direciton of E/l.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and panelling to be paid for separately): For fixed portion.

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 4.0 mm thickness

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. (The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.)

Water proofrng for Old and New Roof Slab :- Providing and laying waterprooflng treatment on roof slab by applying two Component, factory a designed ready to use, acrylic modified flexible,material applied with brush, roller or spray for wate proof i n g coating as per manufactlrer specificatio With following steps :-

(a)surface preparation :-Provrding and cleaning of concrete surface to remove dLrst, oil, grease including removal of existing loose paint / coating, and cement laitance by cleaning with compressed air & water jet including all materials, labour, tools complete. Ponding test to be done after plugging all outlets and to be checked from sofftt to identify seepage, leakage. On identiiication of seepage, cement grouting to be done with non shrink expanding admixture of Sika lndia Pvt.Ltd. / MYK Schomberg / Dr Fixit/Fosroc or equrivallent. Providing and reparing of all corners and joinis such as those betr,veen the parapet wall and the roof slab etc shall be chamfered with '150mm X '150 mm fillet of mortar (Cement: sand - 1:4) admixed with acrylic polymer of Sika/ Fosroc/MYK Schomberg/Dr Fixit or equivalent Before chamfering a prime coat shall be given with the sl u rry ?!gc!ylic polyrner Repai rin g su rface irreg ularities, damaged concretein base slab, dead cracks if any, with an acrylic polymer modilied repair moriar ir;cluding a coat of bonding agent of the same with ceme nt slurry rncluding all rnaterial, labour, tools complete.

(b)1st Coat :- Apply 1st coat of two component acrylic modified, ready to use, llexrble cementitious material on surface saturated dry roof and inside wall of Parapet wall upto 600 mm by brush or roller. After 1st coat of application ,45 gsm oI Fibre glass cloth to lay when the first layer is still green. 1st coat should be applied @1.50 kg/SqmUcoat For the fJUrpose of n'ieasurernent tite entire treated surface will be measured."

(c) :2nd Cr:ai :-T,: apply the 2nd coat of two component acrylic modified, reatiy to-use, flexible cementttious material right angle to the '1st coat over the glass fibre liad surface. 2nd coat should be applied @0.7 kgl Sqrnt/coat. For the pltrpose of measurement the entire treated surface will be rneasurecl." Alte r three days of drying the 2nd coat, therainwater ouilets to be plugged and ponding test to be done for 48 hours to rrjerrtify se epage, leal<age from soffit and if found necessary rectification lo be plugged and ponding test to be done for 48 hours to identify seepage, leakage from soffit and if found necessary rectifcation to be done as per satrsfaction of E/C protected from damage before screed over it. Watqr proofing Brand:*Sika Topseal 109hi / Fosroc Brushbond RFX/ Dr Fixit Pidiffin 2Kl MYK Aqraiin TG Product Performance - Chemical Base Part A. Acrylic copolmer, Part B Specially graded cementitious powder - Density 1.6 l.rg/l (mixcd density) at +27oC Tensile Strength - 2 lllmm2 after 28 clays (with Fibre cloth) (According to ASTM D 2370)Prillcut Bond Streric;tl-r '-2 I'J/mm2 (concrete lajlqry) (Aqgcrdlglq ISO 4624) Slant-Shear Bond Strength -4 N/mm2 (According to FIP 5.'15) Elongation at Break -35% without Fibre Cloth and 20% wilh Fibre Clot (Accordrng to ASTM D 2370)

(d) Protection of treated surface with PCC- The treated surface should be covered with 25mm/50mm PCC of M-20 grade(1:1.5:3) with proper slope ( '1:120) towards tlre rain outlets in alternatepanels of 2 mt x 2mt keeping 6 mrn gap betuieen the panel joint. lntegralwater proofing admixture conforming to lS 2645 @ of 100 ml per bag of of cement to be added in the scree d concrete(pard separately for thts ltems).-All corners shall be charrmfered with 150mm X 150 mm fillet. The rainwater outlets shall be just leveled with the screed concrete to ensure smooth discharge of water - the peripheral gaps between pvc pipe outlet and concrete surface slrould be packed properly with rich concrete and the peripheral mouih to be sealed with moisture insensitive epoxy putty of Sika lndia Pvt.Ltd / IVIYK Schomberg / Dr FixiUFosroc .For the purpose ofrreasurement the entire treated surface will be measured."

(e) Groove of PCC surface should be filled with Polysulphide Sealant (Paid Separately) Brand - Sika lndia Pvt Ltd / MYK Schomberg / Dr Fixit/Fosroc Warranty for Five years.

Covering of treated surface wrth PCC :- Providing 25 mm thick Cementn Concrete M20(1:'1.5:3) r'naintaining slope in alternate 2 mIx 2 mt panels with aaproved quality of stone chips of 20 mm to 6 mm size graded and clcaned sand of F M 2 5 io 3 including screening,shuttering,and mixing cerite nt c0ncrete in mixer with admixture of integral water proofing and placing rn position,strikirrg cLrring,t-a]glgnd royality all complete as per buildirrg specifictionJand direction of E/l.Panels that has been left should be casteci nextday.-lhere should be 6 mm gap between Panels.Brand- Sika *Plastocrate plus,MYK proof WP10, Fosroc- Conplast X421ic , Dr Frx,t Prdiproof LWr

Provrding and filling of 6 mm thick Groove between 25 mm PCC Panels with Polysulphide Sealant (Poring Grade)as per drawings and technical specifications and direction of E in Charge (with 18% GST).Brand:-SikaPolysulphide, Fosroc-l-hioflex 600 Dr. Fixit Pidiseal PS(42P),MYK Seal PS or Euivallent

Providing and fixing in position 25mm thick bituminastic board (shalitex or equivalent as per IS:1838-1983) in expansion or construction joints in barrage and its allied works as per specification and direction of E/I.

Providing and fixing sheet covering over expansion joints with iron screw as per design. Aluminium fluted strips 3.15 mm thick.

200 mm wide

Providing & Applying high quality acrylic modified resin based texture of Dholpur/Red sand stone Pattern with anti algae and UV resistance properties to be applied as intermediate finish in desired pattern @ 43.04 kgs/10 sqm to form film of 1- 1.5 mm thickness after scrapping and properly cleaning the surface to remove loose particles from the plaster surface, followed by top coating with Premium Acrylic Smooth exterior paint with Silicone additives of required shade by two or more coats @ 1.43 litres/10 sqm, complete as the direction of Engineer -in-Charge.

Providing & fixing on wall face unplasticised - Rigid P.V.C. rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion . Single socketed pipes. 110 mm dia

Providing and fixing on wall face unplaqsticised- PVC moulded fitting/ accessories for unplaqsticised- PVC rain water pipes confirming to IS: 13592 TYPE A,including jointing with seal ring confirming to IS: 5382 leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

Bend 87.5 degree 110x110x110mm

Shoe (Plain)110mm shoe

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less thaN 440 grams.

Providing and fixing unplasticised PVC pipe clips of approved design to unplasticised PVC rain water pipes by means 50X50X50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand) and making good the wall etc. complete - 110mm

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge

Cleaning Grass and Removal of Rubbish

Providing 250 mm wide BRICK DRAIN in cement mortar (1:6) with avarage 150mm. Clear depth and 250 mm apron including cost of earthwork involved with 75m cement concrete (1:4:3) over one brick designation 75A, flat soling in proper grade and slope at the base , the drain dully plastered in C.M.(1:3) with puning over exposed surface all complete as per building specification and direction of E/I.

Supplying and fixing C.I. cover without frame for manholes : 560 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg

Making soak pit 2.5 m diameter 3.0 m deep with 45x45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design.

with common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Labour for laying, fitting and fixing NP2 R.C.C. spu pipe with colars in lines, level and grade and providing approved jointing materials and joints properly filled to make them leak, proof including providing sight rails, bonning rod, night guard, Red light and barrier etc. all complete as per specification and direction of E/I. 150mm dia RCC spun pipe - Upto 3.0 metre depth of invert below G.L.

Supplying NP2 R.C.C. hume pipe with colour as work site as per direction of E/I. 150mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge 100 mm nominal size dia

Supplying, filling, spreading & leveling stone boulders of size range5 cm to 20 cm, in recharge pit, in the required thickness, for allleads & lifts, all complete as per direction of Engineer-in-charge

Supplying, filling, spreading & leveling gravels of size range 5 mm to10 mm, in the recharge pit, over the existing layer of boulders, inrequired thickness, for all leads & lifts, all complete as per directionof Engineer-in-charge

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mmto 2 mm in recharge pit, in required thickness over gravel layer, for all leads& lifts, all complete as per direction of Engineer -in-charge

DT : Basic rates for 125/115mm dia drilled Tube-well for drilling in all kinds of soil and rock for installation of hand pump with DTH rig Machine all complete including supplying all materials, labours, tools, drilling, rigs, air compressor and equipments as well as fuel lubricant, for making 125/115 mm dia boring etc. and cost of transporting rig machine and other vehicle up to site of work as per specification and direction of E/I.. (Basic Rates) Drilling upto 30 mtr. Depth below G.L. in Rural Area

Bricks (1K+ 7P = 8 KM.)

Coarse Sand (10KM.)

Stone Chips ( 22 KM.)

Stone Metal ( 22 KM.)

Supplying, fitting and fixing 40 mm high viterous white glazed earthen ware E.W.C. with "p" trap of Parry Hindustan or any other I.S.S. make including supplying & fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fittings with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450 grms. , 15 mm P.V.C. alkathene pipe 45 cm long with brass coupling at both ends and white/ black plastic solid state seal and lead of commander/ cuckoo or other I.S.S. make with hinges or screw etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l. (A) With "P" trap (b)10.0 lit. low level P.V.C. cistern

Supplying, fitting and fixing vitreous white glazed earthen ware I.W.C. of parry hindustan or any other ISS approved make with 100mm HCI p trap 15 litres CI pull and let go flushing cistern of names or other ISS equivalent make complete with all fittings CI or C C bracket 32mm alkethene / PVC telescopic flush pipe about 2m long with one brass coupling and clamps GI chain and pull including supplying and fixing a pair of vitreous white glazed earthenware footrest to be fixed in floor 15mm CI body brass spindle stop cock of weight not less than 50 grames 15mm PVC connection pipe 450mm long and coat of red oxide primer etc all complete as per specification and direction of E/I.

(A) 580 mm long with 10.0 litre low level PVC cistern

Supplying, fitting and fixing flat back or angular lipped front vitreous white glazed earthern ware urinal of Hindustan "Parry" or any other approved ISS make with 5 ltrs. Capacity C.I. automatic fushing cistern of reliance for any other ISS approved make with all fittings with C.I. or RS brackets standard size G.I. flush pipe with fitting clamps 15mm C.I. body brass spindle stop cock of approved quality weight not less than 400 gms. 15mm PVC alkethene pipe 450mm long with brass coupling at both ends and doing plumber points including painting of exposed part with two coats of approved paint over a priming coat of red oxide cutting wall and floor making good the same etc. all complete as per speciifcification and direction of E/I. Flat back or standing corner (600X350mm)

supplying fitting and fixing vitreous white glazed earthen ware wash hand basin of parry or hindustan or any other I.S.S approved make supported on painted C.I OR R.S bracket 32mm C.I brass waste 15mm dia C.I body brass spindle stop cock of approved quality of weight not less than 350 grames, 32mm PVC wate pipe 750mm long with brass coupling with one end and making plumber joints etc.all complete as per specification and direction of E/I.

Providing and fixing gun metal full way valve of approved quality all complete as per specifcation and direction of E/I.

20mm dia.and weight not less than 300 gms.

25mm dia.and weight not less than 500 gms.

32mm dia and weight not less than 700 gms.

40mm dia and weight not less than 1.0 kg.

Providing and fixing brass/ C.I stop cock of approved quality all complete as per specification and direction of E/I (A) Brass Stop Cock (a) 15 mm dia

Cutting chajjas or concrete for laying PVC Pipe and restoring the same with R.C.C. (1:2:4) brick work in cement Mortar (1:4) and cement plaster 1:4 as per specifiction and direction of E/I

Making holes in walls for laying G.I Pipes and restoring the same atfer pipe Laying as per specifiction and direction of E/I (b) 250mm thick wall

Cutting drain width wise above GL for laying H.C.I pipe and restoring brick work in cement mortar (1:4) 12mm cement plaster in C.M. (1:4) with neat cement punning as per specifciation and direction of E/I.

Making holes in wall for laying H.C.I pipes and restoring the same after pipe laying as per specifciation and direction of E/I. (i) 125 mm Dia

Supplying all tolls and labour and cutting chajja cornice for laying H.C.I pipes and making good the same as per specification and direction of E/I.

Supplying, fitting and fixing bathroom fittings of approved make and as per IS specification all cost complete as per direction of E/I. (all rates have been adopted from the basic rate from SOR + 15% for labour and Contractors profit)

Pillar cock (Long neck)

Bib cock - long thread

Angular stop cock L.T

Glass shelf

Flush valve complete with 32mm size control cock & flange

32mm dia. PVC waste pipe 750mm long with Coupling

40 mm dia. PVC waste pipe 70mm long with Coupling

15mm C.P. nipple with coupling

Steel jali - 100mm dia.

Providing Solvent cement

Providing and fixing Pressure adjustable shower with revolving joint

Towel ring

Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/I

Mirroes of 6 mm thick plat glass bevelled edge mirror including C.P brass revolving fitting 3mm ply wood board and C.P hinges to fix with mirror. (i) 600mm x 450mm size

(i) C.P. brass towel rail 20mm X 600mm with bracket container

(ii) C.P. brass dish container medium quality with screw and hinges etc.

Providing and fixing 15mm dia and 45cm long PVC connection pipe with heavy quality brass coupling at both ends etc all complete as per specification and direction of engineer in charge

Supplying, fitting and fixing white glazed fire's clay sink of approved make with overflow arrangements supported on C.I or R.S painted brackets 40mm , dia cp brass waste with C.P brass chain and rubber plug 40mm dia P.V.C waste pipe about 750mm long with brass coupling at one endand 15mm C.I body brass spindle bib cock of approved quality of weight not less than 450 grams including cutting wall and making good the same etc. all complete as per specifcation and direction of E/I. (iii) Lab sink 450mm x 300mm x 150mm

Supplying, materials and labour for constructing inspection chamber of designation class 75B bricks size 750mm deep, 600X450mm internal dimension having 250mm wall thickness in cement mortar (1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600X475mm G.I. cover with frame (weight not less than 35kg) alongwith earth work in excavation and 80mm thick PCC (1:3:6) in foundation and refilling all complete as per specification and direction of E/I.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS 8931, 15mm dia nominal bore of approved brand C.P. fittings

Providing and fixing PTMT extension nipple 15mm size with 12" BSP thread 70mm length and 30mm breadth and weighing not less than 32gms of approved make

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing PTMT BottleTrap forWash Basin and Sink .

Bottle trap 31mm single piecemoulded with hight of 270 mm, effective length of tail pipe 260mm from the center of the waste coupling, 77mm breadth with 25mm minimum water seal weighing not less than 260 gms.

Providing and fixing stainless steel A ISI 304(18/8) kitchen sink as per IS:13983 with C.I. brackets and staom;ess stee; plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required

Kitchen sink with drain board - 510X1040mm bowl depth 250mm

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i.e fixing the pipe with clamps at 1Mtr. Spacing. This includes jointing of the pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of E/I. Concealed work including cutting chases and making good the walls etc.

15mm nominal bore

20mm nominal bore

25mm nominal bore

32mm nominal bore

External work - 40mm nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

15mm nominal bore

20mm nominal bore

25mm nominal bore

32 mm nominal bore

40mm nominal bore

50mm nominal bore

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth.

Granite Stone of approved shade

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

75 mm diameter

110 mm diameter

Providing and fixing on wall face unplaqsticised- PVC moulded fitting/ accessories for unplaqsticised- PVC rain water pipes confirming to IS: 13592 TYPE A,including jointing with seal ring confirming to IS: 5382 leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

Single Tee with door

Bend 87.5 degree

75 mm bend

110 mm bend

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Semi rigid pipe

32 mm dia

40 mm dia

Providing and fixing square mouth S.W. gully trap grade 'A' complete with C.I. Grating brick masonary chamber with bricks of class designation 75 and water tight C.I. Cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design

100x100 mm size P type with common burnt clay F.P.S.(non module) brick of class designation 7.5

Constructing brick masonary road gully chamber 50x45x60 cm with bricks of class designation 75 in cement mortar 1:4 (1 cement :4 coarse sand ) including 500x450 mm precast RCC horizontal grating with frame complete as per standard design .

with common burnt clay F.P.S.(non module) brick of class designation 7.5

Supplying and fixing PVC fittings of approved make confirming to IS : 1729 including supplying nails and bobbins, fixing solutions including earth work or masonary work cutting and remaking and providilding as the case may be all complete as per specification and direction of E/I. ( Add 15%)

PVC plain bend 100mm dia.

Floor trap - 100mm dia.

Ring rubber

Door piece

Cost of Drilind 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.

(a) From 0.00 M to 50.00 M below G.L.

(b) From 51.0 M to125.00 M

(c) From126.0 M to150.00 M

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia

Development of tube well in accordance with IS : 2800 (part I) andIS: 11189, to establish maximum rate of usable water yield withoutsand content (beyond permissible limit), with required capacity aircompressor, running the compressor for required time till well isfully developed, measuring yield of well by "V" notch method or anyother approved method, measuring static level & draw down etc. bystep draw down method, collecting water samples & getting testedin approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessoriesetc., all as per requirement and direction of Engineer-in-charge

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp

Supplying 100mm dis submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump. Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages 2 HP

Supply fitting and fixing of standered make starter pannel Board with arrangement of all necsssury protection including all taxes ,royalty etc all complete job as per direction of E/I.

Supplying fitting and fixing 3 crore 4 sqmm Flat copper submersible cable FINOLEX / HEVELS make including all taxes ,royalty etc all complete job as per direction of E/I.

Supply fitting and fixing lowering 50 mm dia G.L. collumn pipe - do - do - all complete job as per direction of E/I.

Supply, Installation, Testing and Commissioning of electric driven, horizontal type, single/multistage, end suction type, centrifugal pump of cast iron body, C.I impallers with carbon steel shaft & mechanical seal directely coupled with TEFC SQ cage foot mounted type induction motors suiitable for operation on 3 phase, 415 volts 50 Hz AC supply having flow rate of min 450 LPM and head of approx 40 mtrs complete in all respect as required or as directed by engineer incharge.

Terrace Booster Pump

Supply and fixing of PVC sheathed following conductor 1.1 KV grade armoured Cable of following sizes including making end termination with compression gland & bimetalic lugs, and support etc.complete as required

3 × 10 sq.mm.(aluminium)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

3 × 10 sq.mm.(aluminium)

Providing and fixing IS marked butterfly valve (PN 1.6) complete with companion flanges, bolts, nuts, rubber insetions etc.

80 mm diameter

100 mm diameter

Providing and fixing check valve (NRV) complete with companion flanges, bolts, nuts, rubber insetions etc.

80 mm diameter

100 mm diameter

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Providing, laying, testing & commissioning of IS 1239 marked black M.S pipe including all fittings i.e bend, elbows, tees, flanges, reducing socket, nuts and bolts, gaskets etc fixed with welded / screwed joints. including necessary excavation, backfilling, removal of surplus soil etc. min. 1 mtr deep excavation and wrapping with anticorrosive treatement with asphalt tape as per IS:10221, refilling the trench etc. OR fixed with screwed or welded joints, hanged with clamps, hanger supports, dash fasteners, bolts, nuts, rubber insertions etc including threading, cutting, welding, edge preparation, painting of approved colour over two coat of primer, cutting & making good the wall/ floor wherever required, complete as required or as directed by engineer incharge. Make:Tata/Nezone/Jindal

100 mm diameter

80 mm diameter

65 mm diameter

25 mm diameter

Providing and fixing S.S Fire Hydrant Valve of approved quality with 63 mm female, instant, ovlique, single outlet, 80 mm flanged inlet, brass spindle, cast iron wheel m A.B.S. blank cap and chain. conforming to IS: 5290 complete with companion flange, bolts, nuts, rubber insertion / compressed asbestos gasket etc. and painted in fire red colour.

Providing and fixing swinging, wall mounting type First Aid Hose Reel of approved quality and made from compresed steel sheet with dust cover, cast iron brackets including 30 m long, 19 mm nominal bore, high presure braided rubber hose as per IS:444 Type hose guide, PVC shut off nozzle with 6 mm outlet and 25 mm nominal bore gun metal inlet valve, bolts, nuts rubber insetion etc. painted in Fire red colour including cutting and making good the walls wherver required.

Providing and fixing in position 63 mm nominal bore and 15 m long synthetic fibre, CP fire hose pipe of approved make bearing IS: 636 -1988 type A mark and having TAC and MMD approved with a pair of 63 x 63 mm gun metal instantaneous type, heavy duty delivery hose coupling (conforming to IS: 903) bound and riveted to the hose pipe with copper rivets and copper wire complete.

Providing and fixing in position short SS brach pipe of approved quality with 63 mm male instatneous type inlet and 15 mm outlet nozzle complete conforming to IS : 903

Supplying, fixing, testing & commissioning of 1 set of 63mm two way instantaneous fire brigade connection (FBC) with inbuilt NRV comprising of SS and four SS instantaneous male inlet coupling confirming to IS:604 with plug and cap with chain as required with nut & bolts, washers, high pressure gasket as required.

Point Wiring in Medium Class PVC Conduit, with Modular type Switch:- Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 Sq.mm FR PVC insulated copper conductor single core cable in surface/recessed with PVC conduit, with modular type switch, modular plate, suitable size of GI box etc as required. FR PVC Copper Wire (Confirming to IS: 694-2010, 1.1 KV) :- Make:- Havells, Polycab, Rajnigandh, RR Cable. (Make of Modular switch Sockets:- Havells (ATHENA), L&T ENGLAZE), Legrand (LYNCUS) , Anchor(WOODS), Schneider-(OPEL)

Group-C

Twin Control Point Wiring in PVC Conduit, with Modular type Switch:- Wiring for twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed Medium Class PVC conduit, 2 way modular switch, modular plate, suitable size of GI box earthing the point with 1.5 Sq. mm FR PVC insulated copper conductor single core cable etc as required. FR PVC Copper Wire (Confirming to IS: 694-2010, 1.1 KV) FR PVC Copper Wire (Confirming to IS: 694-2010, 1.1 KV) :- Make:- Havells, Polycab, Rajnigandh, RR Cable. (Make of Modular switch Sockets:- Havells (ATHENA), L&T ENGLAZE), Legrand (LYNCUS) , Anchor(WOODS), Schneider-(OPEL)

Power plug wiring in PVC conduit (2x4 sq.mm.):- Wiring for light/power plug with 2x4 Sq.mm FR PVC insulated copper conductor single core cable in surface/recessed Medium Class PVC conduit along with 1 No. 4 Sq.mm FR PVC insulated copper conductor single core cable for loop earthing etc. as required. FR PVC Copper Wire (Confirming to IS: 694-2010, 1.1 KV)Make:- Havells, Polycab, Rajnigandh, RR Cable.

Circuit/Sub-main wiring in PVC Conduit:- Wiring for circuit/ submain wiring along with earth wire with the following sizes of FR PVC insulated copper condcutor, single core cable in surface/ recessed Medium Class PVC conduit as required. FR PVC Copper Wire (Confirming to IS: 694-2010, 1.1 KV) Make: Havells, Polycab, Rajnigandh, RR Cable.

2x1.5 Sqmm + 1x1.5 sqmm earth wire

2x2.5 Sqmm + 1x2.5 sq mm earth wire

2x4.0 Sq.mm + 1x4.0 Sq.mm earth wire.

2x6.0 Sq.mm + 1x6.0 Sq.mm earth wire .

4x6.0 Sq.mm + 2x6.0 Sq.mm earth wire.

4x10 Sq.mm + 2x6.0 Sq.mm earth wire.

TV Cable in Existing Conduit:- Supplying and drawing Co-axial TV Cable RG-6,0.7mm solid copper conductor PE insulated,shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed PVC conduit as required. (Confirming to IS: 694-2010, 1.1 KV) Make:- Havells, Polycab, Rajnigandh, RR Cable.

S/F PVC Conduit: Supplying and fixing of following sizes of med Class PVC conduit of 2 mm thick along with the accessories in surface / recess & cutting the wall and making good the same in case of recessed conduit as required . (Make:- Polycab, Precision, AKG)

S/F Modular type Switch / Socket:- Supplying and fixing of following switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as requried. (Make of Modular switch Sockets:- Havells (ATHENA), L&T ENGLAZE), Legrand (LYNCUS) , Anchor (WOODS), Schneider-(OPEL)

5/6 amps switch

15/16 amp switch

3 pin 5/6A socket outlet

6 pin 15/16 amp socket outlet

TV antenna socket outlet

S/F Modular type electronic fan regulator:- Supplying and fixing 2 modules Stepped type electronic fan regulator on the existing modular plate & switch box including connections but excluding modular plate etc. as requried. (Make :-Havells, Legrand , Anchor, Schneider.)

S/F Modular blanking plate:- Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. (Make - Havells, Legrand , Anchor, Schneider.)

Supply and fixing of following size/ modules, GI box along with modular base & cover plate for modular switch/ regulator in recess, including connection as required. (Make :- Havells, Legrand , Anchor, Schneider).

1or 2 module (78mmx 78mmx 45mm)

4/5 module (78mm x 140mm x 50mm)

6 module (78mmx 205mmx 50mm) (for 2 nos. 6A Sockets & 2no. 6A Switch)

S/F Light plug point with modular type accessoris:- Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 Amp modular socket outlet and 5/6 A modular type switch, connections painting etc. as reqd. (for Light plug point). (Make:-Havells, Legrand , Anchor, Schneider, L&T.)

S/F Power plug ponit with modular type accessories:- Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 5/6 & 15/16 Amp modular socket outlet and 15/16 A modular type switch, connections painting etc. as reqd. (Make:- Havells, Legrand , Anchor, Schneider, L&T.)

S/F Ceiling Rose:- Supplying & fixing of 2 pin, 5 amp Ceiling rose on the existing junction box/ wooden block including connection etc. as required. (Make:- Anchor, Kona)

S/F Batten / Angle Holder:- Supplying and fixing brass batten/angle holder including connection etc. as required. (Make:- Anchor, Kona)

S/F Call Bell Buzzer:- Supplying and fixing call bell/buzzer suitable for single phase, 230 V, complete as required. (Make:- Anchor, reputed)

ITC fluorescent fitting directly on surface:- Installation, testing and commissioning of suspended pre-wired ,fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc., directly on ceiling or on wall including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

ITC fluorescent fitting with Down Rods:- Installation, testing and commissioning of suspended pre-wired ,fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc., including supplying and fixing ball and socket arrangement, 2 Nos. down rods of 20 mm dia X 1.6 mm thick steel conduit upto 30 cm length, painting and wiring the down rods and connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

ITC ceiling fan:- Installation, testing and commissioning of Ceiling fan, icluding wiring the down rods os standard length (Up to 30Cmm) with 1.5 sq. mm FR PVC insulated, copper conductors, single core cable etc. as required.

ITC exhaust fan upto 450 mm sweep:- Installation of exhaust fan upto 450 mm sweep in the existing opening, including making the hole to cut the size of the above fan, making good the damage, including connection, testing, commissioning etc as required.

S/F SP MCB DB:- Supplying and fixing following way, SP&N MCB doubel distribution board of sheet steel for 240 Volts on surface /recess complete with tinned copper bus bar, neutral busbar, earth bar, detachable gland plate, interconnections, phophatized and powder coated painted including earthing etc. as required ( But without MCB/RCCB/ ISOLATOR). (Make:-SIEMENS-Bitaguard, LEGRAND-Ekinox³-, SCHNEIDER-ACTI-9, L&T-AU)

8 Way Double Door

12 Way Double Door

S/F TP MCB DB: - Supplying and fixing following way, horizontal type double door three pole & neutral, sheet steel, MCCB distribution board, 415V, on surface/ recces , complete with tinned copper bus bar, neutral bar, earth bar, din bar interconnections, powder painted including earthing etc. as required (But without MCCB/RCCB/Isolator) (Make:-SIEMENS-Bitaguard, LEGRAND-Ekinox³-, SCHNEIDER-ACTI-9, L&T-AU

6 ways (4+18) Double Door. (horizontal type)

8 ways (4+24) Double Door. (horizontal type)

S/F 'C' Series MCB:- Supplying & fixing 5 amps to 32 amps rating 240/415 volts 10 kA, 'C' curve Miniature Circuit Breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. ( Make:-LEGRAND- DX³/SCHNEIDER- ACTI-9/ABB-S200MSIEMENS- BETA GUARD/ L&T- AU VERSION).

6-32 Amps. Single Pole

6-32 Amps Double Pole

40 Amps Double Pole

6/32 Amps TPN

63 Amps TPN

S/F SP MCB Blanking Plate:- Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.(Make:- L&T, Legrand, Schneider,Siemens)

S/F SPN RCCB:- Supplying & fixing following rating double pole (Single Phase & Neutral) 240 V, Resudual Curren Circuit Breaker (RCCB) , having a sensitivity current uo to 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. (Make:- LEGRAND- DX³/SCHNEIDER- ACTI-9/ABB-S200MSIEMENS- BETA GUARD/ L&T- AU VERSION.)

P/F MV Danger Notice Plate:- Providing & fixing of M.V. danger notice plate of 200 mm x 150 mm, made of mild steel, at least 2 mm thick, and vitreous enamelled white on both sides, and with inscription in single red colour on front side as required.

EARTHING SYSTEM

G.I. Pipe Earthing:- Earthing with G.I. Earth Pipe 4.5 Meter long , 40mm dia including accessories, and providing massonry enclosure with cover plate having locking arragement and watering pipe etc. with charcoal/cock and salt as required. LT Panel- 2 Nos. UPS - 1 nos. Total - 3 Nos.

Supplying and laying of 8 SWG G.I. copper wire at 0.50 meter below ground level for conductor earth electride, including soldering etc. as required.

S/L 25mmx5mm G.I. strip as strip earth electrode :- Supplying and laying 25 mm X 5 mm GI strip at 0.50 meter below ground/surface as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50 mm).

LIGHTNING CONDUCTOR

P/F G.I. lighting conductor finial:- Providing and fixing of Lightning Conductor finial, made of 25 mm dia 300mm ling, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

Reverting, Sweating and soldering Lightning Conductor Tape:- Reverting, Sweating and soldering of Copper/G.I. Tape (with another Copper/G.I. tape, base of the finial or any other mettalic obect) as requried.

P/F G.I. lightning conductor tape in horzontal run :- Providing and fixing G.I. Tape 20mmx3mm thick on parapat or surface of the wall for lightning conductor complete as required. (for Horizontal Run).

P/F G.I. lightning conductor tape in Vertical run:- Providing and fixing G.I. Tape 20mmx3mm thick on parapat or surface of the wall for lightning conductor complete as required. (for Vertical Run).

G.I. Pipe electrode with Salt/Charcoal:- Earthing with G.I. Earth Pipe 4.5 Meter long , 40mm dia including accessories, and providing masonry enclosure with cover plate having locking arragement and watering pipe etc. with charcoal and salt as required.

S/L 25 x 5mm G.I. earth strip in 50 mm below ground:- Supplying and laying 25mmx5mm G.I. Strip at 0.50 meter below ground as strip earth electrode, including connection/ termination with G.I. nut bolts, spring washer etcas required. (Jointing shall be done over and 2 sets of G.I. Nut Bolts & Spring washer spaced at 50mm).

Supply of 1200 mm sweep ISI marked ceiling fans complete with double ball bearing, motor, blades, downrod, canopies, capacitor, suitable for operation on 230 volts, 50 Hz., 1 phase, AC supply connection with 1.5 sq.mm PVC Copper wire complete as required with 2 years warranty. Colour of Ceiling Fan- White/Ivory. (Make- Havells/USHA/GEC/ Crompton Supply of 48" (1200 mm) Sweep Ceiling fan Make :Usha/Crompton/ Havells/GEC.

SITC of 230 mm (9") Exhaust fan (Metal body) suitable for single phase 230 volts, 50 Hz., AC supply complete with motor, louvers/shutters etc. complete as required. Make :- Usha/Crompton /GEC/Havells .

SITC of 300 mm (12") Exhaust fan (Metal body) suitable for single phase 230 volts, 50 Hz., AC supply complete with motor, louvers/shutters etc. complete as required. Make :- Usha/Crompton /GEC/Havells .

LED LIGHT FIXTURES (JSR 2021 -Rates) CORRIGENDUM All the LED lamp shall be of minimum 60 or above lumens per watt and the LED BATTEN TUBE LIGHTS & other LED light fixtures shall be of 100 or above lumens per watt. LM 79 and LM 80 reports need to be submitted with all accessories by the contractor. All LED Lights (Make & Model nos. of LED Liughts are to be approved by Engineering Incharge & Consultant before procurement.) Make:-Havells/Philip/ Wipro/ Jaquar

SITC of following rating Street Lighting Luminarie with pressure die-cast housing and toughened glass cover, IP-66 protection, LUMINOUS EFFICARY 110/lm/w, with lens in existing pole or pipe for supply voltage, 100-270V, AC, 50Hz, luminarie shall be confirm to IS; 10322 part-5/section-3 and shall be complete with all necessary accesoreies as required. (To use as building outer light in 5ft long 40 mm G,I, Pipe with 3 nos.Clamps and nut bolts) (LED light fixtures shall be of 100l/m or above. (LM 79 and LM 80 reports need to be submitted , 50,000 burning hrs, and two years warranty) Make:-Havells/Philip/ Wipro/ Jaquar

45/48 W LED Strret Light (tobe use as Building Outer Lights)

SITC of following rating recess/surface mounted LED round/square shape Down Light Luminarie with pressure die-cast housing for single phase supply voltage. Luminarie shall be confirm to IS; 10322 part-5/section-2 or IEC 62722 with all necessary accesoreies as required. (100l/w , 5700K Cool white, rated voltage- 220/240V. (LM 79 and LM 80 reports need to be submitted , 50,000 burning hrs, and two years warranty) Make:-Havells/Philip/ Wipro/ Jaquar

15/16 W Square Down light Surface

18/20 W Square Down light Recess

1' x 1' LED Panel Light

SITC of following rating surface mounted LED 4ft Batten tube light fitting suitable for 230V, 50 Hz, single phase supply etc all complete as required. wall mounted LED type batten fitting complete with electronic diver and LED etc. directly on wall including connections with 1.5 Sq. mm FR PVC insulatted copper conductor and earthing the body etc. as requiered. (LM 79 and LM 80 reports need to be submitted , 50,000 burning hrs, and two years warranty) Make:-Havells/Philip/ Wipro/ Jaquar

20/22 W LED Tube Light (4 FT) Batten type.

All the LED lamp shall be of minimum 60 or above lumens per watt and the LED BATTEN TUBE LIGHTS & other LED light fixtures shall be of 100 or above lumens per watt. LM 79 and LM 80 reports need to be submitted , 50,000 burning hrs, and two years warranty). Make:-Havells/Philip/ Wipro/ Jaquar

Supply of 9W/10W LED Bulb in existing holders. (Confirming to IEC : 62722) , Make:-Havells/Philip/ Wipro/ Jaquar

Cost of 9W/10W LED Bulb

SITC of LED 2 ft Mirror light with power 8/10W, rated voltage 230W, 50 HZ, aluminium /PC body with running life minimum 30000 hrs. ( LM 79 and LM 80 reports need to be submitted, 50,000 burning hrs, and two years warranty) Make:-Havells/Philip/ Wipro/ Jaquar

Cost of LED 2 ft Mirror light with power 9/10W,

2x20W 4ft LED Batten Tube Light (Confirming to I.E.C. 62722):- SITC of double LED Tube light Fitting made of diacast aluminium housing 2x20W LED Bettle Tube light sritable for surface or suspended mounded suitable for 230V, 50 Hz, single phase supply etc all complete as required, complete with electronic diver and LED etc., including connections with 1.5 Sq. mm FR PVC insulatted copper conductor and earthing the body etc. as requiered. LM 79 and LM 80 reports need to be submitted, 50,000 burning hrs, and two years warranty) Make:-Havells/Philip/ Wipro/ Jaquar

Supplying and fixing Surface mounted 9/10 Watt CFL / LED type bulk head e comprising of pressure die casr housing with acrylic diffuser (IP65) and complete with integrated electronic driver etc. directly on wall /ceiling including connection with 1.5 sq.mm FR PVC insulated copper conductor cable and earthing the body etc as required. LM 79 and LM 80 reports need to be submitted, 50,000 burning hrs, and two years warranty). Make:-Havells/Philip/ Wipro/ Jaquar

5 KVA ON Line UPS (Single Phase Input & Single Phase Output) With Accessories

Supply, fitting, fixing, testing and installation of 1 no. 5 KVA, ON Line UPS Single phase input and single phase out put power system of in put voltage 100V/ AC +/- 5% to 300V AC +/- 5% , Frequency range 40 HZ to 60 Hz, +/- 10% and out put voltage range 415V +/-1%, AC frequency range, 50Hz, +/-1% poower factor>_ 0.90 @ Full Load, 0,8/3.1, Harmonic distrortion -< 2% THD (Linear Load): 5% THD (Non- Liniear Load) along with required Batteries, Battery Stand, UPS Box Battery Lead etc as required. (minimum 30 minutes back up) Make UPS:- Numeric (Legrand), APC (Schneider), Vertive(Emersion) (Warranty-2 yrs.)

Cost of 1 no. 5 KVA ON LINE Single Phase in and Single Phase out UPS

SITC of 1 no. TROLLY Fof double Tubular Battery

SITC of 2 no. 12v/150Ah Sealed Maintance free (SMF) battery with 24 months replacement Gurantee, IS1652:1991) . Make:- Battery-Exide, Amar-Raja, Quantum.

Total cost of 1 Set 5 KVA UPS, Batteries & Accessories ( a+b+c) (Single Phase in and Single Phase Out)(minimum 30 minutes back up)

Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc. as required

80 mm dia

100 mm dia

NONE SCHEDULE ITEMS

Providing & fixing Stainless Steel ( 304 Grade ) Letters on Wall Surface. as per direction of Engineer-In-Charge. 450 mm Hight

Wall Painting (Art Work) With Acrylic Emulsion Paint as per Artwork Approved by Architect on External Wall over Wall putty.

Providing and fixing Wall mounted Prima 304 Stainless Handicap grab bar, Size- 350 mm long for Barrier Free Toilets at position as per specificatio and direction of manufacture and E/I.

Providing and fixing Wall mounted Lipka 304 Stainless Handicap grab bar, Size- 600 mm long for Barrier Free Toilets at position as per specificatio and direction of manufacture and E/I.

Providing and fixing Wall mounted Kaiser Vitals 304 Stainless Handicap grab bar, Size- 300 mm long for Barrier Free Toilets at position as per specificatio and direction of manufacture and E/I.

Fabrication, Supplying, Installation, Testing & Commissioning of electrical control panel of cubical construction, wall mounted type, fabricated out of 2mm. thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection, and accessories mounting and internal wiring, earth terminals, numbering etc. complete in all respects, suitable for operation on 415 V, 3 phase 50 HZ AC supply with enclosure protection class IP 42.

For Terrace Pump

Pressure Gauge Assemble with Gate/Ball Valve

Air release Valve / Drain Valve

MS Structure support for piping

Providing and fixing 25 mm nominal gun metal gate valve class I with CI wheel of approved quality with union (Screwed end)

Supplying and fixing of hose cabinet of size 450mm x 450mm x 250mm made of 2mm thick M.S. sheet with 6mm thick glazed glass door including necessary locking arrangment suitable to accomodate 1 nos. 15 mtr. long hose pipe, 1 no. branch pipe mounted on wall or raised brick platform and duly painted with post office red externally and white internally with synthetic enamel paint complete in all respect.

Providing , fixing Dry Chemical Powder (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ‘IS 14609’ , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester Powder Coated As per ‘IS 15683’ ISI mark Fire Extinguishers. Operating Temperature: - (-) 20oC to (+) 55oC Suitable for ‘A’ ‘B’ ‘C’ Class of FIRE complete in all respects (4 Kg Capacity)

Carbon Di-oxide Type , Gas Confirming to IS ‘15222’ , Cylinder Confirming to ‘IS 7285’ & PESO approved ,Controllable Discharge Mechanism, Discharge Hose & Horn As per ‘IS 15683’ & ‘IS 2878’ ISI mark Fire Extinguishers (Wheel Type or Squeeze Grip Type). Operating Temperature :- (-)20oC to (+)55oC Suitable for ‘B’ ‘C’ Class of FIRE (4.5 Kg Capacity)

Providing , fixing Modular type Fire Extinguishers for electrical rooms (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ‘IS 14609’ , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester Powder Coated As per ‘IS 15683’ ISI mark Fire Extinguishers. Operating Temperature: - (-) 10oC to (+) 55oC Suitable for ‘A’ ‘B’ ‘C’ Class of FIRE complete in all respects (5 Kg Capacity)

RO WATER PURIFICATION SYSTEM

Supply , fitting fixing and commissioning of INDIAN WATER INC. PURE WATERFOR LIFE Fully automatic with autocut off RO Potable WaterPuri 2000 Plus 25 Litre RO+UV+UF Water Purifier Electrically oparated • Purification Technology RO+UV+UF• Capacity 25 Litre • Filter - Pre-filter (optional), sediment filter, activated carbon filter, anti-scalant filter, post-UF filter, • Membrane Type 80 GPD,• Power Features- • Power Requirement- 110V - 300V, 50 Hz, • Operating Voltage - 24V DC V along with all required accessories, like, connecting wires, pipes, stand and fixing euipments along with drain Pipe in put pipe and etc as required. Make- Aquagard, Voltas, Kent.

Cost of Water Purifire INDIAN WATER INC. PURE WATERFOR LIFE 2000 Plus 25 Litre RO+UV+UF Water Purifier Electrically oparated • Purification TechnologyRO+UV+UF• Capacity 25 Litre •

LT PANEL FOR SCHOOL BUILDING

Supplying, designing and manufacturing in correct alignment position, effecting proper connection of all incomer and outgoing, unloading, shifting to the location, installation, commissioning and testing of LT Panel of 14 SWG CRCA sheet (2 mm) steel IP –42, dust and vermin proof, floor mounting with Base Channel size - 75 mm x 40 mm x 6 mm (ISMB Channel) with a proper lifting arrangement.

The cubical type LT Panel should be suitable for operation on 415V, 50Hz, 3 Ph. AC supply and fault level 36 KA with front operated construction including separate fabrication arrangement for fixing all MCCB. The sheet steel under go minimum 7 tanks treatment followed by finishing powder coating of minimum 60 micron thickness duly compartmentalized having accessories mounted inside the cubical panel, earthing with 2 Nos. earth studs. The Panel shall undergo epoxy powder coated paint, colour RAL 7035

The panel shall be provided with a thermostatically controlled heating arrangement with 1 No. 10W LED BULB to take care of high humidity conditions. A 6/16A socket as service outlet (single phase) shall be provided in one of the compartments as service outlet in the panel. Panel shall be so designed as to have minimum 10% spare feeders/space. . All cable terminations shall be from bottom/ top. The complete panel shall be fuse less type, for control circuits 2A MCB's to be used.

All openings shall be covered by soft rubber gasket, enclosure shall be galvanized. Panel shall have suitable cable entry from bottom and suitable arrangement for aluminum cables for all M.C.C.B.

The Panel Builder must be CPRI approved. Panel builder must produce test certificate for Type Tested & Short Ckt withstand capacity as per IEC-60439-II from CPRI during tendering and during inspection, panel builder must carry above test certificates.

AL. BUS BAR

Bus bar shall be suitable for 300A, 415V/50Cys/50KA TPN bus bar chamber of suitable length with (E91EWP) Electrolytic Aluminium bus bars. All bus bars and interconnections shall be of suitable size Aluminium bus bar, current density of Aluminium shall not be more than 0.8 Amps/sq.mm cross sectional area of Bus Bar with removal gland plates, cable glands, at sending and receiving ends. In Main LT Panel interconnection of MCCB with the main Bus -bar with 2.5, 4 , 6 and 10 Sq mm PVC FRLS Cu. wire. The Aluminium bus bar shall be with heat shrinkable PVC Slived Red, Yellow, Blue & Black as (RYB & N ) after temperature and in closer de-rating maximum allowable temp. of bus bar shall be 90 degree C.

Panel Builder will provide shop drawing SLD & GA drawing along with BOM with CAT. No. of each and every components and switch gears of LT Panel for approval of Consultant. Panel Builder shall visit the site before manufacturing the Panel. Inspection of the Panel shall be carried out at Panel Builder's factory by the Consultant before final delivery for that all arrangements shall be made by the contractor.

The Name Plate for each feeder must be in Anodized Aluminium Sheet.

Size of incoming cable:- 1R 3.5C 300 Sq.mm. Al. Ar. Cable.

Make of MCCB - L&T D-Sine/ Legrand DPX³ / Schneider-NSX / Siemens - 3VL.

Make of MCB - (10kA-C-Series.) L&T U Version/ Legrand-Dx³/ Schneider-Acti / Siemens.

All 4 pole MCCB with thermomagnetic based release must have follwing characterstics:-

1. Icu=100% Ics.

2. With positive Isolation Marked.

3. With adjustable short circuit and over load.

4. As per IEC 60947-2.

Bill of Material of Main LT PANEL:-

1 Set Of Fabrication part of LT Panel & busbar system, in CRCA Sheet Steel enclosure (IP-42) without any components & its busbar system, in CRCA Sheet Steel enclosure without any components. Name of Panel Builder :- JMD ELECTROTECH, KOKAR, STECT POWER INDUSTRIES, BIT, Mesra, Shivalic Power Control Pvt Ltd, TTS Systematix Private Ltd, Tatisiway, Meditron, Meshra, Ranchi or any approved Panel Builders of above make Switch Gears.

INDICATING

1 Sets Multifunction Meter having LED display accuracy Class 1 as per IEC 62053-21, RS-485 port, in built RTC, Aux Supply: 44-277Vac/dc. Parameters: Volts, Amps, PF, THD, F, W, Wh, VA, VAh, Var, Varh, Runhrs, Onhrs Interrupts, THD for V&I per phase. Make:- Rishabh /L&T/Schneider

3 nos. CT of different power as per incomer /5VA -5 class one Epoxy resin cast CT (3 Nos.)=1 Set. Make:-Kappa / Matrix/Rishabh.

3 Sets Phase indicating light shall be protected by 2 Amps SP MCB's for incomer & outgoing. Make:- AE/ Rishabh /L&T/ Schneider

INCOMER

1 No. 250A/FP/25KA/ MCCB thermomagnetic release type, and S/C, O/L protection, with Rotary Handle & Spreader links.

OUT GOING

5 Nos. 63 A FP MCCB (25KA) with thermomagnetic release type with S/C & O/L protection with front rotary handle type with spreader links. (4 nos. for Power DB & 1 no. as spare)

2 Nos. 25 A FP MCCB (25KA) with thermomagnetic release type with S/C & O/L protection with front rotary handle type with spreader links. (2 Nos. as spare )

INTERLOCKING

Provision of Mechnical interlocking between 125A/FP/25KA MCCB as common incoming and 1 No. of 125A on load Change over for D.G incomer, in such a way so that the two supplies are not parallel at any time.

1 No. 125A TPN on load Change over panel mounted open execution type and suitable bus arrangement for Cable termination. Make- L&T/Sucomo.

1 No. 125A/FP/25KA/ MCCB thermomagnetic release type, and S/C, O/L protection, with Rotary Handle & Spreader links.

6 Nos. 25 A FP MCCB (25KA) with thermomagnetic release type with S/C & O/L protection with front rotary handle type with spreader links. (4 No. for Light DB & 2 Nos. as spare)

2 Nos. 63A DP MCB. (10KA) 'C' Curve. (5 KVA UPS incoming & 1 no. as spare)

4 Nos. 32A DP MCB. (10KA) 'C' Curve. (3 Nos. for Building Outer Light & 1 No. as spare)

Total Cost of LT Panel of School Building

LT PANEL FOR HOSTEL BUILDING

Supplying, designing and manufacturing in correct alignment position, effecting proper connection of all incomer and outgoing, unloading, shifting to the location, installation, commissioning and testing of LT Panel of 14 SWG CRCA sheet (2 mm) steel IP –42, dust and vermin proof, floor mounting with Base Channel size - 50 mm x 50 mm x 6 mm (ISMB Channel) with a proper lifting arrangement.

The cubical type LT Panel should be suitable for operation on 415V, 50Hz, 3 Ph. AC supply and fault level 36 KA with front operated construction including separate fabrication arrangement for fixing all MCCB. The sheet steel under go minimum 7 tanks treatment followed by finishing powder coating of minimum 60 micron thickness duly compartmentalized having accessories mounted inside the cubical panel, earthing with 2 Nos. earth studs. The Panel shall undergo epoxy powder coated paint, colour RAL 7035

The panel shall be provided with a thermostatically controlled heating arrangement with 1 No. 10W LED BULB to take care of high humidity conditions. A 6/16A socket as service outlet (single phase) shall be provided in one of the compartments as service outlet in the panel. Panel shall be so designed as to have minimum 10% spare feeders/space. . All cable terminations shall be from bottom/ top. The complete panel shall be fuse less type, for control circuits 2A MCB's to be used.

All openings shall be covered by soft rubber gasket, enclosure shall be galvanized. Panel shall have suitable cable entry from bottom and suitable arrangement for aluminum cables for all M.C.C.B.

The Panel Builder must be CPRI approved. Panel builder must produce test certificate for Type Tested & Short Ckt withstand capacity as per IEC-60439-II from CPRI during tendering and during inspection, panel builder must carry above test certificates.

AL. BUS BAR

Bus bar shall be suitable for 200A, 415V/50Cys/50KA TPN bus bar chamber of suitable length with (E91EWP) Electrolytic Aluminium bus bars. All bus bars and interconnections shall be of suitable size Aluminium bus bar, current density of Aluminium shall not be more than 0.8 Amps/sq.mm cross sectional area of Bus Bar with removal gland plates, cable glands, at sending and receiving ends. The interconnection of MCCB with the main Bus -bar shall be with 2.5, 4 , 6 and 10 Sq mm PVC FRLS Cu. wire. The Aluminium bus bar shall be with heat shrinkable PVC Slived Red, Yellow, Blue & Black as (RYB & N ) after temperature and in closer de-rating maximum allowable temp. of bus bar shall be 90 degree C.

Panel Builder will provide shop drawing SLD & GA drawing along with BOM with CAT. No. of each and every components and switch gears of LT Panel for approval of Consultant. Panel Builder shall visit the site before manufacturing the Panel. Inspection of the Panel shall be carried out at Panel Builder's factory by the Consultant before final delivery for that all arrangements shall be made by the contractor.

The Name Plate for each feeder must be in Anodized Aluminium Sheet.

Size of incoming cable:- 1R 3.5C 95 Sq.mm. Al. Ar. Cable.

Make of MCCB - L&T D-Sine/ Legrand DPX³ / Schneider-NSX / Siemens - 3VL.

Make of MCB - (10kA-C-Series.) L&T U Version/ Legrand-Dx³/ Schneider-Acti / Siemens.

All 4 pole MCCB with thermomagnetic based release must have follwing characterstics:-

1. Icu=100% Ics.

2. With positive Isolation Marked.

3. With adjustable short circuit and over load.

4. As per IEC 60947-2.

Bill of Material of Main LT PANEL:-

1 Set Of Fabrication part of LT Panel & busbar system, in CRCA Sheet Steel enclosure (IP-42) without any components & its busbar system, in CRCA Sheet Steel enclosure without any components. Name of Panel Builder :- JMD ELECTROTECH, KOKAR, STECT POWER INDUSTRIES, BIT, Mesra, Shivalic Power Control Pvt Ltd, TTS Systematix Private Ltd, Tatisiway, Meditron, Meshra, Ranchi or any approved Panel Builders of above make Switch Gears.

INDICATING

1 Sets Multifunction Meter having LED display accuracy Class 1 as per IEC 62053-21, RS-485 port, in built RTC, Aux Supply: 44-277Vac/dc. Parameters: Volts, Amps, PF, THD, F, W, Wh, VA, VAh, Var, Varh, Runhrs, Onhrs Interrupts, THD for V&I per phase. Make:- Rishabh /L&T/Schneider

3 nos. CT of different power as per incomer /5VA -5 class one Epoxy resin cast CT (3 Nos.)=1 Set. Make:-Kappa / Matrix/Rishabh.

3 Sets Phase indicating light shall be protected by 2 Amps SP MCB's for incomer & outgoing. Make:- AE/ Rishabh /L&T/ Schneider

INCOMER

1 No. 160A/FP/25KA/ MCCB thermomagnetic release type, and S/C, O/L protection, with Rotary Handle & Spreader links.

OUT GOING

12 Nos. 25 A FP MCCB (25KA) with thermomagnetic release type with S/C & O/L protection with front rotary handle type with spreader links. (4 Nos. as spare )

2 Nos. 63A DP MCB. (10KA) 'C' Curve. ( Qrt. DB & 1 no. as spare)

4 Nos. 32A DP MCB. (10KA) 'C' Curve. (2 Nos. for Building Outer Light & 2 No. as spare)

Total Cost of LT Panel Hostel Building.

LT PANEL FOR KITCHEN & DINING

Supplying, designing and manufacturing in correct alignment position, effecting proper connection of all incomer and outgoing, unloading, shifting to the location, installation, commissioning and testing of LT Panel of 14 SWG CRCA sheet (2 mm) Steel IP –42, dust and vermin proof, Floor Mounting with Base Channel size - 25 mm x 25 mm x 4 mm (ISMB Channel) with a proper lifting arrangement.

The cubical type LT Panel should be suitable for operation on 415V, 50Hz, 3 Ph. AC supply and fault level 25 KA with front operated construction including separate fabrication arrangement for fixing all MCCB. The sheet steel under go minimum 7 tanks treatment followed by finishing powder coating of minimum 60 micron thickness duly compartmentalized having accessories mounted inside the cubical panel, earthing with 2 Nos. earth studs. The Panel shall undergo epoxy powder coated paint, colour RAL 7035

All openings shall be covered by soft rubber gasket, enclosure shall be galvanized. Panel shall have suitable cable entry from bottom and suitable arrangement for aluminum cables for all M.C.C.B.

The Panel Builder must be CPRI approved. Panel builder must produce test certificate for Type Tested & Short Ckt withstand capacity as per IEC-60439-II from CPRI during tendering and during inspection, panel builder must carry above test certificates.

AL. BUS BAR

Bus bar shall be suitable for 100A, 415V/50Cys/50KA TPN bus bar chamber of suitable length with (E91EWP) Electrolytic Aluminium bus bars. All bus bars and interconnections shall be of suitable size Aluminium bus bar, current density of Aluminium shall not be more than 0.8 Amps/sq.mm cross sectional area of Bus Bar with removal gland plates, cable glands, at sending and receiving ends. The interconnection of MCCB with the main Bus -bar shall be with 2.5, 4 , 6 and 10 Sq mm PVC Cu. wire. The Aluminium bus bar shall be with heat shrinkable PVC Slived Red, Yellow, Blue & Black as (RYB & N ) after temperature and in closer de-rating maximum allowable temp. of bus bar shall be 90 degree C.

Panel Builder will provide shop drawing SLD & GA drawing along with BOM with CAT. No. of each and every components and switch gears of LT Panel for approval of Consultant. Panel Builder shall visit the site before manufacturing the Panel. Inspection of the Panel shall be carried out at Panel Builder's factory by the Consultant before final delivery for that all arrangements shall be made by the contractor.

The Name Plate for each feeder must be in Anodized Aluminium Sheet.

Size of incoming cable:- 1R 3.5C 50 Sq.mm. Al. Ar. Cable.

Make of MCCB - L&T D-Sine/ Legrand DPX³ / Schneider-NSX / Siemens - 3VL.

Make of MCB - (10kA-C-Series.) L&T U Version/ Legrand-Dx³/ Schneider-Acti / Siemens.

All 4 pole MCCB with thermomagnetic based release must have follwing characterstics:-

1. Icu=100% Ics.

2. With positive Isolation Marked.

3. With adjustable short circuit and over load.

4. As per IEC 60947-2.

Bill of Material of Main LT PANEL:-

1 Set Of Fabrication part of LT Panel & busbar system, in CRCA Sheet Steel enclosure (IP-42) without any components & its busbar system, in CRCA Sheet Steel enclosure without any components. Name of Panel Builder :- JMD ELECTROTECH, KOKAR, STECT POWER INDUSTRIES, BIT, Mesra, Shivalic Power Control Pvt Ltd, TTS Systematix Private Ltd, Tatisiway, Meditron, Meshra, Ranchi or any approved Panel Builders of above make Switch Gears.

INDICATING

1 Sets Multifunction Meter having LED display accuracy Class 1 as per IEC 62053-21, RS-485 port, in built RTC, Aux Supply: 44-277Vac/dc. Parameters: Volts, Amps, PF, THD, F, W, Wh, VA, VAh, Var, Varh, Runhrs, Onhrs Interrupts, THD for V&I per phase. Make:- Rishabh /L&T/Schneider

3 nos. CT of different power as per incomer /5VA -5 class one Epoxy resin cast CT (3 Nos.)=1 Set. Make:-Kappa / Matrix/Rishabh.

3 Sets Phase indicating light shall be protected by 2 Amps SP MCB's for incomer & outgoing. Make:- AE/ Rishabh /L&T/ Schneider

INCOMER

1 No. 100A/FP/25KA/ MCCB thermomagnetic release type, and S/C, O/L protection, with Rotary Handle & Spreader links.

OUT GOING

3 Nos. 25 A FP MCCB (25KA) with thermomagnetic release type with S/C & O/L protection with front rotary handle type with spreader links. (1 Nos. as spare )

2 Nos. 63 A FP MCCB (25KA) with thermomagnetic release type with S/C & O/L protection with front rotary handle type with spreader links. (1 Nos. as spare )

Total Cost of LT Panel Kitchen & Dining.

TV SYSTEM Accessories for MATV NETWORK SYSTEM

Supply, erection, testing and commissioning of splitter / tap off mounted in suitable sizes MS boxes for MATV system and shall be suitable for interactive system. Make- Reputed (as directed by Consultant)

Two Way (S-2)

Two way tap off (T2)

Supply. Fitting, fixing and testing of 43" LED Flat TV full HD, resolution-1366 x 768 with 1 x HDMI, 1 x USB, remote control & battery for remote control along with all accessories & 1 year warranty.

Supply, fitting, fixing and testing of Auto-manual Voltage Stabilizer with High Voltage cut off 0.25 KV 220V Range- 100 to 280V Single Phase 50 Hz Stabilizer along with cord & plug. Make:- As per approved make list.

IP Setup Box. (Make:- As per approved make list)

Add 18% GST

Add 1% Labour cess 1%

Mahadeva Enterprises

M/S MANOJ KUMAR PANDEY