REPAIR MAINT SERVICING OF B VEHICLE AND REPAIR REPLACEMENT OF STREET SECURITY LIGHT LED STREET LIGHT FITTINGS ROADWAY LUMINARIES TIMER PANELS HIGHMAST LIGHTS AND OTHER CONNECTED MISC WORKS UNDER GE I GOS

Amount

Dismantling and disconnecting of unserviceable parts of Tata Mobile 207 Vehicles reinstalling after repair/replacement of unservice-able parts complete to entire satisfaction of Engr-in-Charge. NOTE: Spare parts required to be replaced shall be measured and paid separately as mentioned here-in-below.

Engine oil

Oil filter element

Diesel filter element (set of two)

Air filter

Brake leather

Front wheel bearing

Coolant

Front shokers

Brake oil

Door lock driver side

Door lock rear door

Counter Shaft

Top gear

Gear Bearing

Synchronizing ring

Gear Oil

Gear Oil Seal

Gear Jain Kit

Fan Belt

Tie rod end

Bush kit complet

Ball joint assembly

Diesel pipe

Yoke and teeth

Shaft Nuts and Bolts

Mirror rolling machine

Engine mounting

U.J cross

Fly wheel Ring

Front Mirror with rubber beading

Head light assembly complet with tube

Main leaf spring

Leaf spring 2nd No

Leaf Spring 4th No

Leaf Spring clump

Nuts and Bolts with washer

Tyre rotation

Cover Inner and outer of size 7.00-16LT

Wiper Arm & Blade

Alternator rectifier

Alternator rotor assy

Side view Mirror

Front indicator assembly

Rear indicator assembly

Ignition cum lock switch

Cluch cylinder assy upper

Clutch cylinder assy lower

Master cylinder assy

Clutch Plate

Pressure plate assy

Clutch release bearing

Dismantling of four wheels by greasing of four wheels including replacement of oil seal and reassembling complete all as directed.

Repair of seat complete including replacement of best quality Rexign, U foam & spring complete all as directed.

Alignment of wheel completely by computerized machine.

Cleaning of radiator assy complete by opening both tanks & cleaning the fins of the radiator by chemical and stopping the leakage by gas welding wherever required

Repair to FIP pump by over hauling the FIP and replacing all the spares of the FIP with the new spares and testing complete on machine all as directed.

Dismentling of Fuel tank assy complete from the vehicle and cleaning by pressure and refitting.

Dismantling and disconnecting of U/S parts of two wheelers Honda/Platina Reinstalling after repair/replacement of U/S parts complete to entire satisfaction of Engr-in-Charge. NOTE: Spare parts required to be replaced shall be measured and paid separately as mentioned here-in-below.

Carburetor assy

Chain and chain sprocket.

Spark plug

Clutch plate

Shock absorber

Lock set complete

Side Looking Mirror

Kilometer cable

Head Light Tube

Back Light Complete

Break shoe Front and rear

Clutch cable complete

Accelerator cable complete

Engine oil

Dismantling and disconnecting of unserviceable parts of EICHER Model No 10.75 Vehicles re-installing after repair/replacement of unserviceable parts complete to entire satisfaction of Engr-in-Charge.NOTE: Spare parts required to be replaced shall be measured and paid separately as mentioned here-in-below.

Engine Oil CRB plus 20W40

Oil filter element

Fuel filter element (set of two)

Door Handle with lock assembly

Door Handle

Coolant

Retreading of Tyres

Front Indicating light assly with bulb

Wheel bearing

Wheel cylinder assy

Break leather

Side view mirror

Head light assy complete with bulb (Halogen type)

Bumper corner

Self Starter Assy

Window glass with beading

Alternator carbon bush

Rectifier assy.

Alternator bearing

Back light assy. complete

Indicator assy.

Cutout 12 volts

Flasher

Main leaf spring

Nuts and Bolts with washer

Centre Bolts

U- Bolts

Wiper Arm & Blade

Ignition cum lock switch

Cluch cylinder assy upper

Cluch cylinder assy lower

Master cylinder assy

Cluch Plate

Pressure plate assy

Cluch release bearing

Fan Belt

Tie rod end

Diesel pipe

UJ cross

Top Gear

Gear Bearing

Synchronizing Ring

Fuel tank cleaning

Gear oil

Gear oil seal

Gear Cain Kit

Main Gear shaft

Repair of self starter by replacing of self bendex, carbon bush set, solenoid switch etc complete.

Dismantling the load springs and refitting after repair and giving suitable tensioning complete all as directed.

Dismantling of four wheels complete by greasing of four wheels including replacement of oil seal and re-assembling complete.

Setting of wheel alignment and setting of brake system including filling of brake fluid in master cylinder kit.

Repair of seat complete including replacement of best quality Rexign, U foam & spring complete all as directed.

Overhauling, greasing of King pin including replacement of oil seal complete.

Denting of vehicle, including welding wherever required

Dismentling of Fuel tank assy complete from the vehicle and cleaning by pressure and refitting.

Supply and fixing in replacement of maintenance free battery 12 volt 92 Ah including battery leads and initial charging of battery. Make:- Exide/ Amron.

Supply and fixing in replacement of maintenance free battery 12 volt 60 Ah including battery leads and initial charging of battery. Make:- Exide/ Amron.

Dismantling and disconnecting of unserviceable parts of Maruti swift Dzire Veh BA No: 23B -1318847X and re-installing after repair/replacement of unserviceable parts complete to entire satisfaction of Engr-in-Charge.NOTE: Spare parts required to be replaced shall be measured and paid separately as mentioned here-in-below.

Engine oil

Oil filter element

Fuel filter element (set of two)

Brake oil

Coolant

Cover Inner and outer of size 165/80R14

Excavation in trenches n .exc 1.5 mtr wide and not exec 1.5 mtr depth and getting out in looses/soft soil complete all as specified

Excavating in trenches not exceeding 1.5 meter wide and exceeding 1.5 meter and not exceeding 3meter in depth for foundation for erection of poles, stays, laying cables, stays etc and getting out in soft/loose soil all as specified and directed.

Returing filling in incl spreading leveling, watering and well ramming in layer not less than 25 cum each layer all as specified.

Removing excavated material to a distance not exc 50M and depositing where directed at a level n.exc 1.5 mtr above the starting point complete all as specified

Supply and fix double wall corrugated HDPE pipe 50mm outer dia for protection of UG cable complete all as specified and directed

M&L PCC 1:4:8 type D 2 using 40 mm graded stone aggregate for filling of pole & stay complete all as directed

M&L PCC 1:3:6 type C 2 using 40 mm graded stone aggregate for filling of pole & stay complete all as directed

M&L PCC 1:2:4 type B1 using 20 mm graded stone aggregate for copining of pole complete all as directed

M & L for tube light grade galvanised with all fittings laid along the pole/in trenches / under road or floor of 50 mm bore including removing the rusted old one complete all as specified and directed.

Supply and fixing steel tubular swaged poles with cast iron base plate, finial taper plug, bolts, nuts, screws as specified type 410 SP-31 (9.0 mtr long) and erecting in position all as specified and directed with shifting of conductors and insulators including painting the exposed portion with two coats of aluminium paint over a coat of red oxide primer and internally through out plus embedded portion with two coats of black bituminous paint over a coat of red oxide primer with and including marking of pole number with black paint in yellow circle including dismantling of existing pole, complete, all as specified and directed.

Supply and fixing in repairs Prestressed concrete pole, 9.0 metres long, 102mm x 172mm at top and l02mm x 279mm at bottom, class 10 and erecting in position all as specified and directed with shifting of conductors and insulators including painting the exposed portion with two coats of weather proof paint complete including dismantling of existing PCC pole, all as specified and directed.

Supply, laying, jointing and testing of XLPE insulated, armoured, heavy duty LT under ground cable 1100 Volts grade with aluminium conductor laid in trenches, on poles, through pipes, fixed to walls etc cross sectional area for 10 Sqmm 2 Core ,complete, all as specified and directed :-

All as per item no. 151 but 16 Sqmm 2 Core.

All as per item no. 151 but 16 Sqmm 4 Core.

All as per item no. 151 but 25 Sqmm 3.5 Core.

M&L Checking /finding out or locating fault of existing LT UG cable laid in under ground /on poles/ walls or any situvations or location inside Gopalpur Mil station up to Vijaya dhar gate and restoring power supply within 8 Hrs period after receiving the call/ Msg from concerned JE E/M or in chain of command.The job includes excavation,Earth work, returning filling and removal, Meggaring /insulation resistance checking ,intermittant jointing of existing cables with new cables with proper LT straighjt through joints etc to restore power supply in all respect including cutting of road path and making good etc all as directed. Note:- 1:- Excavation / earth work,new cable,cable protection pipes, re laying of existing cable, LT cable joints,JB boxes, clamps, Brackets,filling of PCC will be measured and paid seperately.Note ;- 2 :- If the fault not rectified in the specified time limit double the rate of job as penality will be debited to contr.

M/L for replacement of Earthing complete with GI earth plate 60x60cmx6mm thick electrode and 4mm dia GI wire as earthing lead.burried directly in ground ( earth pit not less then 2.25 metres deep below ground level ) with top edge of the plate not less then 1.5 metres below normal ground level. connected to GI wire earth lead 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of SSR Part-I and incl earth work,PCC pit and RCC cover,watering pipe 20 mm dia med grade,funnel,wire mesh,protection pipe 15 mm dia light grade up to 7.5 mtr length of earth wire,charcoal dust and salt etc and connected to earthing test point all as specified and as directed by Engr-in-charge.

M/L for replacement of Earthing complete with GI earth plate 60x60cmx6mm thick electrode and using galvanised iron strip 32 x 6 mm as earthing lead burried directly in ground ( earth pit not less then 2.25 metres deep below ground level ) with top edge of the plate not less then 1.5 metres below normal ground level. connected to iGI strip 32x6 mm as earthing lead means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of SSR Part-I and incl earth work,PCC pit and RCC cover,watering pipe 20 mm dia med grade,funnel,wire mesh,protection pipe 40 mm dia light grade up to 7.5 mtr length of earth wire,charcoal dust and salt etc and connected to earthing test point all as specified and as directed by Engr-in-charge.

Supply and fixing of moulded case circuit breaker Four pole 100 Amps 16 KA capacity 415V 50Hz with Ics = 50% Icu as per IEC 60947-II suitable for isolation class II front face fixed overload and fixed short circuit setting. taking out the old unserviceable complete all as specified and directed by Engr-in-Charge.

S & F in replacement of new generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens embedde PC coverhaving bottom opening seperate driver compartment with IP 66 protection and impact resistance of IK08 with suitable for pole dia 42 mm of capacity 45 watts complete all as specified and directed.

S & F in replacement of new generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens embedde PC coverhaving bottom opening seperate driver compartment with IP 66 protection and impact resistance of IK07 with suitable for pole dia 42 mm of capacity 60 watts complete all as specified and directed.

Supply and fixing in replacement of LED driver for suitable for 45W to 60 W complete all as specified and directed .

Supply and Fix in repair for PVC junction box of size 270 x 225 x 135 mm with Aluminium bus bar 200 Amps capacity -4 No's . MCB SP 6 Amp - 1 No and having provision of cable hole in bottom for two to three armoured cables of size 25 Sqmm 3.5 core, connection box shall be fitted on street light pole and fixing arrrangements i.e. MS clamps etc deemed to be provided by the contractor all as specified and directed .

Taking down and replacement of existing unserviceable street light fitting bracket with new brackets made out of 32mm bore GI pipe, light grade, tubing bend to shape, 1.2 metre long, fixed to pole/wall, painting with two coats of aluminium paint over a coat of red oxide primercomplete, all as specified and directed. (MS clamps nut bolts etc will be measured and paid seperately)

S&F of Cable jointing kit for 1.1 KV (Earthed) grade cable for straight through heat shrink type joint complete with jointing material and accessories suitable for 4 core XLPE armoured aluminium conductor cable of size 10 to 25 sqmm complete

Taking down the motorised / manual High Mast Lights circular grid accomodating MH/MV light fittings any cap over a ht of 15 mtr to the ground, taking aside, replacing the unsv control gears/ light fittings with LED fixtures and raising back to its original position upto 15 mtr etc complete all as specified and as directed (Rates quoted shall be incl of replacing required accessories where specifically not mentioned but required to complete the Job except LED fixtures)for taking down,Necessary T&P items required for lowering the circular grid shall be in possession with contr ie suitable handle for mannual operation or spare motor for lowering with cable required for completing the job all as directed.

Repairing the Light fittings of the motorised / manual High Mast Lights of any size and capacity of light fittings by taking down the mast with the help of crane over a ht of 15 mtr to the ground, taking aside, replacing the unsv control gears/ light fittings with LED fixtures and raising back to its original position upto 15 mtr etc complete all as specified and as directed (Rates quoted shall be incl of crane and replacing required accessories where specifically not mentioned but required to complete the Job except LED fixtures) Tools/plants & machinery required for performing the job will be arranged by contractor at his own cost.

S&F in replacement astronomical + digital time switch complete all as specified and directed.

Supply and fix in replacement of automatic modular contactor with 3NO+1NC, 40A, 3 module, 50HZ suitable for timer switch of street light complete all as specified and directed

Boring of holes horizontally for laying of 40mm dia pipe (minimum depth 0.60 Mtr from top level) under road, Pavement, hard standing complete all as specified and directed.

Supply and fix post-top lantern 25 watt ruby clear energy saving, environmental friendly, long life aesthetically designed with IP 65 symmetrical light distribution, spun aluminium landscape luminaire with high power LEDs as light source

M&L in replacement of new generation energy saving and environmental friendly, long, life pressure die cast aluminium housing flood light with PC diffused lens enclusre over LED for glare free light of capacity 120 watts, 240 volts, 50Hz complete all as specified and directed.

Cutting and trimming of tree branches 3 mtr all around of street light any size which is obstructing illumination of street light and touching LT Over head line by using required tools and plants incl removing trimmed tree branches. (Note : Each cleaning will be measured and paid separetely)

Supply and fixing in repairs SP 5-32 amp rating 240V, 10KA 'C' curveminiature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning.

Supply and fixing in repairs SPN 32-40 amp rating 240V, 10KA 'C' curveminiature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning.

Supply and fixing in repairs TPN 40-100 rating 415, 10KA 'C' curveminiature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning.

S&F in repairs PVC insulated and FR PVC round sheathed copper conductor(flexible), 1100 volts, conforming to IS 694 of size1.0 Sqmm 3 core complete all as specified and directed

M&L for in repairs service wire sheathed flat 2 core aluminium conductor of size 4 Sqmm, 1100 volts grade complete all as specified and directed

M&L for in repairs service wire sheathed flat 2 core aluminium conductor of size 6 Sqmm, 1100 volts grade ,complete all as specified and directed

M&L for in repairs service wire sheathed flat 2 core aluminium conductor of size 10 Sqmm, 1100 volts grade complete all as specified and directed

S&F in repairs PVC conduit pipes 19 mm outer dia corrsion free, thermal resistance -5 degree to +60 degree celcius, self extinguishing complete all as specified and directed

S & F in repairs Galvanaised Iron cross arms channel, bracing, support, clamps etc fabricated structured steel, sections, including nuts, bolts, washers etc and cutting to required length beat to any shape drilling holes, fixed on poles or jointed by means of elect welding complete incl painting with 2 coats of aluminum paint over a coat of red oxide primer after preparation of surfaces incl taking down / dismantling the old items ,complete all as specified and directed

S&F in repairs energy saving environmental friendly long life bamboo LED bollard light of capacity 8 watts, 240 volts, 50 Hz with IP 65 complete all as specified and directed

Taking out old UNSV XLPE/PVC insulated, armoured, heavy duty LT under ground cable 1100 Volts grade with aluminium conductor from trenches, from poles/walls etc cross sectional area for 10 Sqmm to 16 sqmm 4 / 2 Core complete, all as specified and directed :-(Excavation/Earth wk will be measured and paid seperately)

All as per item no. 185 but for 25 Sqmm 3.5 Core.

Relaying of serviceable U/G cable retrived from site of size 10 to 16 sqmm 2/4 core ( Cable protection pipe /sand brick etc will be measured and paid seperately)

Relaying of serviceable U/G cable retrived from site of size 25 to 35 sqmm 2/3.5/4 core ( Cable protection pipe /sand brick,jointing kit etc will be measured and paid seperately)

M&L GI pipe Light gde 15 mmdia for earth lead protection ,complete all as specified and directed

Cutting chases and making good and cement work in any wall /floors and making good with PCC1:3:6 complete all as directed

Horizontal auguring under Road/Path etc for passing cables/pipes and making good ,complete all as specified and directed

Excavation of concreate or Road surface for laying of cables or pipes and making good the disturbed patch with PCC 1:3:6 ,complete all as specified and directed

Cutting chases for inserting pipe/cables and making good with cement work and tiling work etc in any wall /floors matching with existing surface of walls or floors all as directed

Removing of PCC 9 Mtr pole by excavation/ Earth work, Breaking of PCC /pole Fdn without damaging of pole and re- errecting at new location with & including excavation/earth work, PCC complete as directed & painting the exposed portion with two coats of weather proof paint complete,Job includes re locating of pole including Fdn wk .

P JAGANNADHARAJU (BID ID -3443954)

HARAGOURI SUPPLIERS (BID ID -3442976)

M/s MAA BHAIRABI ENTERPRISES (BID ID -3441729)

Likitha Enterprises (BID ID -3443887)