REPAIR MAINTENANCE OF PUMPS MOTOR, STARTERS, SUBMERSIBLE PUMP SET AND CONNECTED ACCESSORIES AND REPAIR MAINTENANCE OF FAN GEYSERS ENERGY METERS AND CONNECTED WORKS AT DCRA DAD KIRTI ENCLAVE AND OTM ACCN UNDER AGE EM II OF GE NW VASCO

Amount

Material and labour for rewinding by authorised service centre for the burnt unsv electric pumping motor for Repairs to AC, 3 phase, 415 Volts, 50 Hz Electric pumping motor as follows: (i) Transport burnt motor to civil work shop. (ii) Dismantling motor assembly removing stator and rotar as seperately (iii) Removing burnt / unserviceable windings completely including insulation material and rewinding stator with super enamelled copper wire of standard specification with standard insulation material ,baking complete and re-assembling stator and rotar assembly fixing back to original position at site and testing, commissioning etc complete all as directed for the following capacity of motors:-

(a) Motor of capacity 40 to 60 HP

(b) Motor of capacity 7.5 to 15 HP

(c) Motor of capacity 20 to 30 HP

S&F DOL/ submersible starter in sheet metal enclouser, AC-3 phase, 415 Volts, 50 Hz, including taking out old unserviceable one all as specified and as directed of the following capacity :-

(a) For Motor 10/7.5 HP, borewell Submersible Starter, AC, 3 Phase, 415 Volts

(b) For Motor upto 6 HP, borewell submersible starter, AC, 3 Phase, 415 Volts

(c) For Motor upto 7.5 HP, DOL Starter, AC, 3 Phase, 415 Volts

M & L for removing existing Centrifugal pump set motor from base frame after disconnecting electrical connections and varnishing, heating and baking the winding of the motor complete and replacing bearings, grinding the shaft etc complete and reassembling and fixing back to original position and testing, commissioning etc all as directed complete for the following:- (Notes :- (1) Replacement of major parts will be measured & paid separately; (2) Any minor part if required will be provided by contractor without any extra cost.

(a) Motor of capacity 50 to 60 HP

(b) Motor of capacity 20 to 40 HP

(c) Motor of capacity 10 to 20 HP

(d) Motor of capacity upto 10 HP

M&L in replacement of coupling set with all accessories for Pump shaft of the following capacity pumping set, including machining, threading, making key slot etc.as directed.

(a) 60/50 HP Pump Set

(b) 40/30 HP Pump Set

(c) 10/7.5 HP Pump Set

M & L for removing existing unserviceable Fan blade from pump set motor of any size / type as per site condition and replacing the same, reassembling and fixing back to original position and testing, commissioning etc all as directed.

Supply only wornout stainless steel Ball bearing of existing size for the following size pumping set complete all as specified & as directed. (MAKE : SKF/NBC/TATA).

(a) 60/50 HP Pumpset

(b) 40/30 HP Pumpset

(c) 20/15/12.5 HP Pumpset

(d) 10/7.5 HP Pumpset

(e) 5.0/3.0 HP Pumpset

M&L in replacement of Pump shaft for following capacity pumping set, including sleeves, machining, threading, making key slot etc. complete all as directed.

(a) 60/50 HP Pump Set

(b) 40/30 HP Pump Set

M&L for replacement of CI impeller of any capacity pumping set all as directed.

(a) 30 to 60 HP Pump Set

(b) Upto 30 HP Pump Set

M&L in replacement of gland coupling brass bush for the following pumping set all as directed:-

(a) 60/50 HP Pumpset

(b) 40/30 HP Pumpset

(c) 15/12.5 HP Pumpset

(d) 10/7.5 HP Pumpset

S&F fully automatic star-delta starter in sheet metal enclouser, AC-3 phase, 415 Volts, 50 Hz, with-over load protector, single phase protection relay and electronic timer, including taking out old unserviceable one all as specified and as directed of the following capacity :-

(a) For Motor 12.5/15 HP Capacity

(b) For Motor 10/7.5 HP Capacity

Removal of existing submersible pump set of any capacity from the existing borewell (by using any method) of depth upto 200m and transporting to workshop for checking and bringing back after repair, reinstalling of submersible pump set in the borewell including testing and commissioning complete all as directed. (Note : (i) The quoted rate shall be deemed to include the cost of any T&P or machinery required for carrying out the work (ii) Replacement/Repair will be measured seperately as supply only items

Supply of the following spare parts for submersible pump against above serial item No 11 :-

(a) GM impeller

(b) GM Neck ring

(c) Coupling sleeve

(d) MS Stud for pump

(e) Bush for submersible motor

(f) Bush for pump

Repairs to AC, 3 phase, 415 Volts, 2900 RPM Electric Submersible pumping motor 10 HP against item no 11 above including Dismantling of burnt motor, cutting and taking out burnt stator winding from motor, cleaning the stator and rewinding with super enamelled water proof copper wire of original gauge/size including re-assembling complete all as specified and as directed.

All as per item no 13.00 above but for 7.5 HP

All as per item no 13.00 above but for 5 HP

Removal of existing submersible pump set of any capacity from the existing borewell (by any means) of depth up to 150 mtr and flushing out till clear water is obtained, conducting yield test with 'V' Notch and reinstallation of submersible pump set in the bore well complete all as directed. Note : The quoted rate shall be deemed to include the cost of any T&P or machinery required for the complete flushing out of the bore well and testing and commissioning of submersible pumpset.

S & F for submerssible cable ,flat, PVC insulated copper conductor stranded type, 1100 volts grade of size 3 core 6 sq. mm size, including jointing of cable with proper kit, connecting to motor and starter with suitable thimble including dismantling the old one complete all as specified and as directed.

M & L for dismantling sewage pumping set 12.5/20 HP pump set by dismantling of suction & discharge pipe line and motor, cleaning the pump by removing the impellar / repair work / over hauling and replacement of worn out parts all as required to bring the pump in perfect working condition including re-assembling installing, testing and commissioning complete all as specified and directed. Note- (i) Cost of minor spare will be born by the contractor (ii) Other spares will be measured and paid seperately

Supply only under mentioned worn out parts of sewage pumping set :-

(a) Pump shaft for 20 /12.5 HP pumping set incl machining, threading, making key slot etc.

(b) Cast iron impeller for 12.5/20 HP Pump

(c) Gland bush for 12.5/20 HP

(d) Ball bearing suitable for 12.5/ 20 HP pump set

(e) Coupling set for MS shaft of 12.5/ 20 HP pump set

(f) Fish Plate bush

(g) Nuts & bolts off sizes

Supply and fix in repairs Cast Iron Foot valve flanged type, including all necessary fittings ie rubber gasket, nuts & bolts, washers all as specified and directed of the following nominal sizes:-

(a) 150 / 125 mm bore

(b) 100 / 80mm bore

(c) 65 / 50mm bore

M & L in repairs swing check type reflux (Non- return) valve,cast iron body, single door, both ends flanged type including all necessary fittings ie rubber gasket, nuts & bolts, flanges, washers of the following nominal sizes :-

(a) 150 mm bore

(b) 100mm bore

(c) 80mm bore

(d) 65mm bore

(e) 50mm bore

Supply and fix in repairs cast iron sluice valve with stainless steel spindle, class PN-1.6, both ends flanged and drilled and fixed by means of new bolts, nuts and washer of galvanised iron of suitable size, including providing and fixing rubber gasket joints with rubber gasket 3mm thick of the following nominal sizes complete all as specified and directed:-

(a) 200mm bore

(b) 150 mm bore

(c) 100 mm bore

(d) 80 mm bore

Supply and fix in repairs Gun metal gate valve, (heavy duty) with iron wheel head, secrewed both ends for iron pipe all as specified and directed of the following sizes :-

(a) 50 mm bore dia

(b) 40 mm bore dia

(c) 25 mm bore dia

(d) 20 mm bore dia

(e) 15 mm bore dia

S & F in repairs pressure gauge, 100 mm size, fitted on delivery side of pump set, including all necessary items required like ball valve & dismantling the old one complete all as specified and as directed. (Make : H-Guru/Fiebig)

S & F in repairs brass air release cock,fitted on pump set, including dismantling the old one complete all as specified and as directed.

S & F Powerfactor meter, digital type, 0 to 1 range, flush mounting type, three phase, 415V, AC including all necessary accessories and dismantling old one complete all as specified and as directed.

S & F indicator lamp LED type, 230 Volts, AC (different colours for indicating R, Y, B phases) with holder incl dismanlting old one complete all as specified and as directed.

S & F in repairs Single phase preventer and connected to existing strater, suitable for centrifugal pump set of capacity 03 HP to 60 HP (Make : Minilec/L&T/BCH)

Supply and laying in repair synthetic rubber insulated mates 2.5mm thick for voltage upto 11 KV ( Size 2X1 M)

Supply and fixing in repairs power contactor, 3 pole, AC, type MNX 50 complete all as specified and as directed. (Make L& T or equivalent in Siemens/C&S)

Supply and fixing in repairs power contactor, 3 pole, AC, type MNX32 complete all as specified and as directed. (Make L& T or equivalent in Siemens/C&S)

Supply and fixing in repairs power contactor, 3 pole, AC, type MNX 18 complete all as specified and as directed. (Make L& T or equivalent in Siemens/C&S)

Supply and fixing in repairs power contactor, 3 pole, AC, type MNX 12 complete all as specified and as directed. (Make L& T or equivalent in Siemens/C&S)

Supply and fixing in repairs, 3 pole power contactor, 3 pole, type MK 1 complete all as specified and as directed. (Make : L& T or equivalent in Siemens/ C&S).

Supply and fixing in repairs, front mounting Add on Auxillary contact block type MNX A1 with 2 NO + 2 NC complete all as specified and as directed. (Make : L&T or equivalent in Siemens/ C&S).

Supply and fixing in repairs, front mounting Add on Auxillary contact block type MNX A2 with 1 NO + 1 NC complete all as specified and as directed. (Make : L&T or equivalent in Siemens/ C&S).

Supply and fixing in repairs, bi-metallic overload relay type MN 5 with single phase protection mounted on the contactor with current carrying capacity ranging from 30 - 50 A complete all as specified and as directed. (Make : L&T or equivalent in Siemens/ C&S).

Supply and fixing in repairs, bi-metallic overload relay type MN 2 with single phase protection mounted on the contactor with current carrying capacity ranging from 9-15 A complete all as specified and as directed. (Make : L&T or equivalent in Siemens/ C&S).

Supply and fixing in repairs, bi-metallic overload relay type MN 2 with single phase protection mounted on the contactor with current carrying capacity ranging from 20-33 A complete all as specified and as directed. (Make : L&T or equivalent in Siemens/ C&S).

Supply and fixing in repairs, bi-metallic overload relay type MK1 mounted on the contactor with current carrying capacity ranging from 0.6 - 18 A complete all as specified and as directed. (Make : L&T or equivalent in Siemens/ C&S).

Supply and fixing in repairs electronic timer ST-100 type ranging from 3 - 10 sec/ 12-120 sec (Make : L&T or equivalent in Siemens/ C&S).

Servicing and maintaining pumping installation by tightening / replacing the gland rope of pump ,replacing rubber coupling ,bushes and clearing the leakage of sluice valves, NRV's, aircock, pressure guage by tightening gland etc. complete at BMF Pump house comprising 4 Nos pump sets of capacity 30 HP -02 No & 40 HP - 02No complete all as specified and as directed.

M & L for replacing rubber coupling of coupling set of any pumpset at different pump house complete all as specified and as directed.

M & L for welding work for the broken pipe flanges / pump set base channel including necessary additional required material, checking/correcting the alignment of pumpset including removing & refixing, cleaning the dust, rust and necessary painting all as specified and directed

M& L preparation of old painted surface of pump installation by removing all dirt, dust, grease, oil etc and painting complete with two coats of synthetic enamel paint of approved colour over a coat of red-oxide primer in Pump set - 02 Nos including their sluice valves, NRV and delivery / suction pipe line in BMF pump house all as specified & directed

All as per serial item 47.00 here-in-before, but at Def Civ area pump house comprising 02 pump sets

All as per serial item 47.00 here-in-before, but at NOFRA Pump house comprising 02 pump sets including valves-06, NRV-6

All as per serial item 47.00 here-in-before,but at 24 Lt's pump house comprising 02 pump sets.

All as per serial item 47.00 here-in-before, but at new Varunapuri Pump house comprising 01 pump sets including valves-03, NRV-3

All as per serial item 47.00 here-in-before, but at Under Water Range area comprising 02 pump sets.

All as per serial item 47.00 here-in-before, but at 203 Pump house comprising 05 pump sets.

All as per serial item 47.00 here-in-before, but at Sewage Pump House comprising 02 pump sets including valves-03, NRV-3

All as per serial item 47.00 here-in-before, but at New leading pump house area comprising 02 pump sets including valves-02, NRV-2

All as per serial item 47.00 here-in-before, but at DAD complex pump house comprising 02 pump sets.

M & L for bacteriological analysis of water sample at DIRECTORATE OF HEALTH SERVICES, ENVIRONMENTAL AND POLLUTION CONTROL WING, PANAJI- GOA complete all as specified and as directed. (NOTE : (a) The water sample should be carried in sterilised bottle/watercan which are to be collected from the SCIENTIFIC OFFICER, ENVIRONMENTAL AND POLLUTION CONTROL WING, PANAJI- GOA) by the contractor Note: Testing to be carried out every month

M & L for Chemical analysis of water sample at DIRECTORATE OF HEALTH SERVICES, ENVIRONMENTAL AND POLLUTION CONTROL WING, PANAJI- GOA complete all as specified and as directed. (NOTE : (a) The water sample should be carried in sterilised bottle/watercan which are to be collected from the SCIENTIFIC OFFICER, ENVIRONMENTAL AND POLLUTION CONTROL WING, PANAJI- GOA) by the contractor Note: Testing to be carried out every month

M&L chemical analysis of treated sewage water collected from STP 260 KLD at NOFRA II location for the following parameters:- (a) BOD (b) COD (c ) Oil and Grease (d) Suspended Solids(TSS) (e) Ph (f) DO (g) E- Coil (h) Coliform (NOTE : (a) The water sample should be carried in sterilised bottle/watercan which are to be collected from the SCIENTIFIC OFFICER, ENVIRONMENTAL AND POLLUTION CONTROL WING, PANAJI- GOA) by the contractor Note: Testing to be carried out every month

M&L Plate earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected using galvanised iron strip 25×4 mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel , including provision of GI pipe 40 mm bore medium grade of required length for protection of earthing lead, GI watering pipe 15mm bore medium grade with PGI sheet funnel and wire mesh , PCC 1:3:6, type B-1 chamber with 50 mm thick pre-cast RCC cover reinforced with 6 mm dia mild steel plain round bars spaced at 100 mm centres both ways with frame, filling the pit with charcoal & common salt surrounding the earth plate,including all necessary excavation & earth work in any type of soil all as shown in Electrical Plate No.3, connected to earthing test point including testing on completion complete all as specified & directed

M&L Continuity conductor or recess or chases or buried in ground or drawn in conduit /pipe or fixed to poles or any other indicated situation for loop earthing etc by 32x6mm galvanised strip

All as per item No 61.00 above but copper strip 32x6mm

M&L in repair chemical earthing with copper earth plate 90x60x5mm & copper earth strip 32x6mm

Checking of pumpset starter or motor for any fault installed at various locations under AGE E/M II of GE(NW) Vasco and carry out necessary repairs in order to keep in working condition Note:- (a) Repairs including material required will be measured and paid under relevant item if required. (b) Equipments/Testing meters required for detecting faults shall be provided by the contractor.

Supply and fix in repairs to nozzle made out of brass of spraying assemblycomplete (As per sample)

S&F in repair RGB light fittings LED water tight type of reputed make as per sample including necessary wiring and service connection all as directed

M&L for overhauling the fountain assembly comprising of cleaning the nozzles, changing the founatin PVC flexible pipe, painting the assembly, replacing the nozzles if required, rubber gasket, checking electrical connections for lights and pump & redoing with water proof tape etc including minor items required all as specified and directed

Repair/servicing to existing dozing plant machine complete system including dosing pump motor, liquid container, suction /delivery pvc pipes, checking of serviceability of power pont service connection to dozing pump and making necessary connection to delivery pipe to to each pump by necessary common header by GI pipe of suitable size whereever applicable in pump houses

Repair to motor shaft / pump shaft including transporting to work shop, grinding, making slot for key if required, polishing and fixing back to position as earlier all as directed.

M & L for PCC (1:2:4) type B1 using 20mm graded stone aggregate as in for foundation with grouting nut & bolt with necessary form work etc including dismantling pumpset with delivery and suction lines and making necessary alteration by fixing pipe and bend, refixing & realigning again after doing foundation at BMF Pump House complete all as specified and directed

S & F in repairs Framed work such as ladders, walk ways, railings & hand rail, shed and frame work for pump channel water supply installation and similar work including cutting tops to shape, drilling holes, notching for wire etc embedded in concrete / masonary complete duly painted with two coats of primier and one coat on synthetic enamel paint, drilling, bolting or reveting con-forming to Fe.290.Gde-E-165 including fixing it on required surface with necessary cement and welding work complete all as specified

Repair /overhauling of 6 BHP Diesel Engine pump set complete in situ by disconnecting and opening suction delivery side GI pipe line connections and checking of diesel injector,tappet system, engine top gasket replacement, cleaning of exhaust manifold, air inlet, piston head cleaning, checking of cylinder bore and fuctional measurment, replacement of piston rings, connecting rod small end big end bearing serviceability, serviceability of gudgen pin,cleaning of crank case by draining out old used engine oil, refilling engine oil of required quantity, timing gear serviceability, checking of pump shaft straitness and pump impeller repcement etc including replacement of any other spares as required and refitting complete engine, pump assembly, testing as per satisfaction of Engineer-in-Charge all as directed.

Dismantling ceiling fans 1200 mm sweep of any make/ model, opening for cutting, taking out existing unserviceable winding wire, rewinding with super enamel copper wire of existing gauge, including varnishing and insulating material with washer, split pin, checknut, hanging clutch, condenser clamp, assembling,with required flexible wire .5 mtr and testing complete all as directed by EIC.

All as per Srl item No.73.00 but for ceiling fans of 1400mm sweep.

All as per Srl item No.73.00 but for exhaust fan 450mm sweep.

All as per Srl item No.73.00 but for exhaust fan 380 mm sweep

All as per Srl item No.73.00 but for exhaust fan size 300mm sweep.

Taking down ceiling fans 1200/1400mm sweep and exhaust fans 450/300mm sweep, removing and cleaning of dust properly, oiling and greasing of bearing with and including replacement of washer, new split pin & any other minor spare parts such as new screw, checknut, pin etc and refixing in position, connecting, testing complete all as directed by EIC.

Replacement of condensor 2.5 MFD. Make : Asian/Tibcon/EPCOS

Replacement of condensor 4 MFD. Make : Asian/Tibcon/EPCOS

Replacement of ball bearing of any size as ordered by Engr-in-Charge Make : SKF/NBC/TATA

Taking out U/S bush from ceiling and making arrangement of ball bearing by lathing at workshop complete all as specified.(Ball bearing will be measured and paid for separately).

Replacement of gun metal bush self oiling of ceiling fans 1200/1400mm sweep.

Replacement of condenser 3.15 MFD. Make - Asian/Tibcon/EPCOS

Replacement of hanging clamp of ceiling fan any size complete all as directed by Engineerr-in-Charge.

Plastic canopy upper and lower for any make of ceiling fan all as specified and directed by EIC, fixed in repairs of best quality as approved by GE

Spray painting of Ceiling/Exhaust fans of any size including fan blades, after scrapping and cleaning old painted surfaces, with synthetic enamel paint including writing of MES No complete all as directed by EIC

Taking down old unserviceable ceilling fans and Supply and Fix in repair Ceiling Fan motor with body complete suitable 1200 mm Sweep Ceiling Fan matching to blade existing location Make : Usha/Bajaj/Crompton / Orient

Supply and Fix in repair Fan Blade set of three suitable of any make and sweep up to 1200 mm sweep Celing Fan matching to existing location. Make : Usha/Bajaj/Crompton / Orient

Sheet Metal Enclosures with socket plug top and MCBs single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of 10 Amps capacity, 240 volts and making connections complete all as specified & directed fixed in repairs. Make: Legrand/ Havells/ Standard

Replacement of plug top 3 pin, 15 Amp, 230 volts ISI Marked Make : Anchor/Havells

All as per Srl item No.91.00 but 5 Amp

Taking down old UNSV exhaust fan by disconneting and providing new exhaust fan 300 MM sweep made of sturdy engineering plastic complete with louvers shutter RPM 1200 , copper winding and acessories , 230 Volt fixing on the same location with the provision of faastners, reconnecting, testing and commissioning complete all as specified. Make:- Polar/ Khaitan/ Bajaj

Repair replacement of fastners of suitable size for hanging of geysers all as specified and directed by Engineer in Charge.

Taking down the unserviceable water storage heater of 25/50ltrs capacity, any type and make, refixing the same after cleaning the scaling deposited in the inner container and water pipe complete all as specified and directed by Engr-in-charge. Note - Replacement of unserviceable bolts incl regrouting shall be deemed to be included in the rate quoted by tenderer. However CPVC fittings shall be measured and paid for separately as supply only.

Repair replacement of Non return valve 15mm dia made of bronze ISI marked heavy duty fixed in repairs complete all as specified and directed.

Repair replcement of water heating element of 1.5 KW capacity in triangular/ Cup type complete all as specified and directed fixed in repairs. Make : Theeta/Daspass/Power pack

All as per Srl item No.97.00 but 2 KW

Replacement of thermostat in triangular/circular shape in the existing Geyser complete all as specified and directed. Make : Elcon/TTE/ Power pack

Replacement of indicator bulb (Red & Green) of approved make complete all as specified and directed.

Replacement of spring loaded Air-release safety valve 15mm dia made of brass as per existing shape and size of approved make complete all as specified and directed.

Replacement of inner container made of copper for 25 ltrs capacity of approved make as per existing size / guage complete all as specified and directed.

All as per Srl item No.102.00 but 50 ltrs capacity.

Replacement of bottom cover in two pieces made of GI sheet duly painted in required/existing size and shape suitable for 25/50 ltrs capacity water storage heater

Brass stop cock CP with capston head, heavy duty of 15mm bore, fixed to iron pipe or brass ferrule complete all as specified and directed fixed in repairs.

Brass bib tap of 15mm bore CP, fancy type with capston head, fixed to iron pipe or brass ferrule, of approved make complete all as specified and directed fixed in repairs.

Supplying and laying of CPVC pipes SDR 13.5 pipes & plain CPVC SDR 11 fittings of 25 mm outer diameter fixed in repairs on walls/ground/floors. Make : Prakash/Surya/Jindal

Replacement of brass/steel assembly heavy duty suitable for 25 ltrs Geyser of any make and size all as directed by EIC.

Replacement of brass /steel assembly heavy duty suitable for 50 ltrs Geyser of any make and size all as directed by EIC.

Glass wool after removing the existing unserviceable Glass wool in between the inner and outer container of Geyser of any cap and make.

Supply only GI Socket 15mm bore heavy duty all as directed by EIC.

Supply only brass Elbow 16 mm bore all as directed by EIC.

Supply only CPVC union socket 16 mm bore, all as directed by EIC.

Supply only water tap heavy duty, all as directed by EIC.

Repair & Repalacement of outer container made of GI sheet duly painted with synthetic enamel paint of approved colour, capacity 25 ltrs fixed in repairs

All as per Srl item No.115.00 but 50 ltrs capacity.

Replacement of PVC connection heavy duty 450mm long suitable for 15mm bore pipe with 2 Nos of brass nut and washer.Make : Prayag/Bharat/Ajay.

Supply only Hex Nipple 15mm bore heavy duty complete all as directed by EIC.

Repair /replacement of old post top lantern sturdy LED bollard with excellent light output its leek PMMA window ensuring maximum illumination aspect in surrounding complete with driver and lamp including mounting base plate and mounting studs and bolts acessories complete. Make:- HAvells cat part No: - MINIMOUNTBL10WLED 830PSYMTOPMMAM(1.0 M) or equavalent in Bajaj / Phillips / Surya / Crompton etc

Repair /replacement of old post top lantern LED type 40 watt 230 Volts Ac outdoor type with decorative post top for 360 degree indirect light IP65 protection with inmpact and corrosion resistant complete with driver and lamp complete.

Taking down of single phase 230 V, 50 Hz energy meters and refing the same with proper copper wire connections through the existing circuit including connection upto Distribution board of 4/8/12 way all as per specified and directed by the Engineer-in-Charge complete.

Repair & Replacement of synthetic rubber insulated mats s 2 mm thick for voltage upto 3.3 KV for electrical purpose as per IS15652-2006 (superseding IS5424) suitable for electrical shock safety of sizes 2 M X 1M.

Repair & Repaceent of LED light fitting 1X9W/1X10 W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size.

S & F in repair junction boxes IP 66/69 protected out door type size 155 x 210 x 92 mm Make : Hensal Model NO : KF 1600 B

Supply & fiing brass tee 16 mm outer dia all as directed by EIC.

Supply & fixing ball valve CPVC 16 MM outer dia all as directed by E1C

Supply, install, testing and commissioning of factory made LT panel wall mounted in replacement of existing panel made out of CRCA sheet of 2 mm thick indoor type double door compartmentalised construction totally enclosed weather, dust and vermin proof with front opening hinged door locking arrangement 415 volt 3 phase 4 wires AC 50 Hz having aluminium busbar for phases and the neutral insulated with PVC sleeves, suitable chamber for fixing single phase electric meter -9 Nos complete, and epoxy powder coat of spray paint over a coat of red oxide primer complete all as specified and directed. Meter box/panel shall be fitted semi concealed on wall. INCOMING (a) Including MCCB 415 volts 4 pole 36 KA breaking capcity fixed magnetic setting type of 200 Amps - 01 No (b) R -Y-B phase LED incating lamps-03Nos (c) 200 Amp TPN main aluminium busbar OUTGOING (a) Including MCB SP & N 32 Amps breaking capacity 10 KA 'C' Curve - 09 Nos (b) Space for mounting single phase energy meter - 09 Nos (c) Copper flexible wires of 6 Sqmm size for all feeders/meter connection.

Supply, install, testing and commissioning of factory made LT panel wall mounted in replacement of existing panel made out of CRCA sheet of 2 mm thick indoor type double door compartmentalised construction totally enclosed weather, dust and vermin proof with front opening hinged door locking arrangement 415 volt 3 phase 4 wires AC 50 Hz having aluminium busbar for phases and the neutral insulated with PVC sleeves, suitable chamber for fixing single phase electric meter -5 Nos complete, and epoxy powder coat of spray paint over a coat of red oxide primer complete all as specified and directed. Meter box/panel shall be fitted semi concealed on wall. INCOMING (a) Including MCCB 415 volts 4 pole 36 KA breaking capcity fixed magnetic setting type of 100 Amps - 01 No (b) R -Y-B phase LED incating lamps-03Nos (c) 200 Amp TPN main aluminium busbar OUTGOING (a) Including MCB SP & N 32 Amps breaking capacity 10 KA 'C' Curve - 05 Nos (b) Space for mounting single phase energy meter - 05 Nos (c) Copper flexible wires of 6 Sqmm size for all feeders/meter connection.

Supply & Laying of galvanised steel tubes medium garde 40 MM complete with all fittings all as directed by Enginner in Charge including making good to disturbed surfaces.

Supply & fix in repairs new ceiling LED surface fitting round 18 watt, 220-240 V AC : 50Hz lights. Make Polycab :- LD O0112019 or equivalent in Phillips, Havells, Bajaj, Crompton Greaves

star freeze service

DOGRA ELECTRICALS

OM SAI ELECTRICALS