Construction of one block 15 tenements Block A3 at Mottaithoppu saram Puducherry Balance work

Amount

CODE NO:2.8.1: Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms , lift upto 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed , within a lead of 50m -All kinds of soil

CODE NO : 4.1.10: Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size)

CODE NO : 4.1.11A: Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:5:10 (1 cement : 5 coarse sand : 10 graded brick aggregate 40mm nominal size)

CODE NO : 2.31: Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30cm measured at a height of 1m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared.

2. REINFORCED CONCRETE WORK: CODE NO : 5.2.2: Reinforced cement concrete work in walls Reinforced cement concrete work in walls (any thickness), including attachedpilasters, buttresses , plinth and sting courses , fillets , columns , pillars ,piers , abutments , posts and struts etc. upto floor five level excluding cost of centering , shuttering , finishing and reinforcement - 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size)

CODE NO: 5.33.2: Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work , using cement content as per approved design mix , including pumping of concrete to site of laying but excluding the cost of centering , shuttering , finishing and reinforcement , including admixtures in recommended proportions as per IS : 9103 to accelerate, retard setting of concrete , improve workability without impairing strength and durability . Note:- Cement content considered in this item is @ 330 kg / cum. Excess or less cement used as per design mix is payable or recoverable separately. - All work above plinth level upto floor V level

CODE NO: 5.9.5: Centering and shuttering including strutting , propping etc and removal of form for - Lintels , beams , plinth beams , girders , bressumers and catilevers

CODE NO : 5.9.6: Centering and shuttering including strutting , propping etc and removal of form for – Columns, Pillars , Piers Abutments , Posts and Struts

CODE NO : 5.9.3: Centering and shuttering including strutting, propping etc and removal of form for - Suspended floors , roofs , landings , balconies and access platform

CODE NO : 5.9.7 :Centering and shuttering including strutting , propping etc and removal of form for - Stairs , (excluding landings) except spiral –staircases

CODE NO : 5.9.19 :Centering and shuttering including strutting , propping etc and removal of form for -Weather shade , Chajjas, corbels etc., including edges

CODE NO : 5.16: Providing , hoisting and fixing upto floor five level precast reinforced cement concrete in shelves including setting in cement mortar 1:3 (1 cement : 3 coarse sand) , cost of required centering , shuttering and finishing with neat cement punning on exposed surfaces but excluding the cost of reinforcement , with 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size)

CODE NO : 5.18.1:Providing precast cement concrete jali 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 6mm nominal size) reinforced with 1.6 mm dia mild steel wire including centering and shuttering, roughening leaning , fixing and finishing in cement mortar 1:3 ( 1 cement : 3 fine sand) etc. complete excluding plastering of the jambs, sills and soffits - 50mm thick

CODE NO : 5.22.6: Steel reinforcement for R.C.C.work including straightening , cutting , bending, placing in position and binding all complete upto plinth level - Thermo -Mechanically treated bars (TISCON / VIZAG / IISCO / SAIL / JSW) Fe - 415 or more

CODE NO : 5.22.8: Providing anticorrosive treatment to HYSD reinforcement with fusion bonded epoxy coating the rate includes cost of anticorrosive coating including cost of powder , sand blasting, cleaning , induction , heating , depreciation of machinery etc, wastage in cut length of bars , provision of wooden battens between rows of coated bars , cover to work bush pins/bar bending machines etc - for bars of 20mm to 32 mm diametre - conforming to IS 13620 -1993

3.BRICKWORK: CODE NO : 6.1.1: Brick work with common burnt clay F.P.S. (non modular ) bricks of class designation 7.5 in foundation and plinth in - cement mortar 1:4 (1 cement : 4 coarse sand)

CODE NO : 6.4.2: Brick work with common burnt clay F.P.S (non modular ) bricks of class designation 7.5 in superstructure above plinth level upto floor five level in all shapes and sizes in - cement mortar 1:6 ( 1 cement : 6 coarse sand)

CODE NO : 6.8: Brick work 7 cm thick common burnt clay F.P.S. (non modular) brick of class designation 7.5 in cement mortar 1:3 ( cement : 3 coarse sand ) in superstructure above plinth level and upto floor five level

CODE NO : 6.13.2: Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level upto floor V level - cement mortar 1:4 (1 cement : 4 coarse sand)

CODE NO : 6.15: Extra for providing and placing in position 2 nos 6mm dia M.S.bars at every third course of half brick masonry

CODE NO : 6.22: Tile brick masonry work 5 cm thick with common burnt clay F.P.S.(non modular ) tile bricks of class designation 10 in cement mortar 1:3 (1 cement : 3 coarse sand) in superstructure above plinth and upto floor five level

4.WOODWORK CODE NO : 9.1.2P : Providing wood work in frames of doors , windows, clerestory windows and other frames , wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately) -Padak wood

CODE NO : 9.20.2 : Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part 1) decorative type , core of block board construction with frame of 1 st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters - 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

CODE NO : 9.23 : Extra for providing lipping with teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured)

CODE NO :9.117.1 : Providing and fixing factory made uPVC door metre frame made of uPVC extruded sections having an overall dimension as below (tolerance +_ 1mm ), with wall thickness 2.0 mm (+-0.2mm), corners of the door frame to be jointed with galvanized brackets and stainless steel screws , joints mitred and plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S.tube of size 19 x 19 mm and 1mm (+-0.1mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer's specification - Extruded section profile size 48 x 40 mm

CODE NO :9.118.1:Providing and fixing to existing door frames - 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59 x 24 mm and wall thickness 2 mm (+- 0.2 mm) with inbuilt edging on both sides . The styles and rails mitred and joint at the corners by means of M.S. galvanised / plastic brackets of size 75 x 220 mm having wall thickness 1.0 mm and stainless steel screws.The styles of the shutter reinforced by inserting galvanised M.S.tube of size 20x20 mm and 1mm (+- 0.1mm) wall thickness . The lock rail made up of 'H' section , a uPVC hollow section of size 100 x 24 mm and 2 mm (+-0.2 mm) wall thickness , fixed to the shutter styles by means of plastic / galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multichambered single panel of size not less than 620 mm, having overall thickness of 20 mm and 1 mm (+_ 0.1mm) wall thickness . They panels filled vertcally and tie bar at two places by inserting horizontally 6 mm galvanised M.S.rod and fastened with nuts and washers , complete as per manufacturer's specification (For W.C. and bathroom door shutter)

CODE NO :10.11.2: Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators , side /top/centre hung, with beading and all members such as 7D,F4B,K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings , complete all as per approved design, (sectional weight of only steel members shall be measured for payment) - Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately)

CODE NO :10.30.1: Providing and fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows all complete with - 4.0 mm thick glass panes

CODE NO :9.62.1: Providing and fixing ISI marked oxidised M.S.sliding door bolts with nuts and screws etc.complte - 300 X 16 mm

CODE NO :9.63.1R:Providing and fixing ISI marked powder coating tower bolt black finish (Barreltype) with necessary screws etc.complete -250 x10 mm

CODE NO :9.63.3: Providing and fixing ISI marked oxidised M.S. tower bolt black finish (Barrel type) with necessary screws etc.complete - 150x10mm

CODE NO :9.66.1R: Providing and fixing ISI marked powder coating handles conforming to IS : 4992 with necessary screws etc.complete - 125 mm

CODE NO :9.165.1B : Providing and fixing of 65 mm Godrej Navatal lock of 7 levers with 3 keys etc complete

5.STEELWORK: CODE NO :10.17: Providing and fixing M.S. fan clamp type I or II of 16mm dia M.S. bar, bent to shape with hooked ends in R.C.C.slabs or beams during laying , including painting the exposed portion of loop, all as per standard design complete

CODE NO :10.25.2: Steel work welded in built up sections / framed work , including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required - in gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

6.FLOORING: CODE NO :11.3.1: Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc .complete - 40mm thick with 20mm nominal size stone aggregate

7.ROOFING: CODE NO :12.15.1: Painting top of roofs with bitumen of approved quality @ 17kg per 10 sq.m impregnated with a coat of coarse sand at 60cudm per 10 sq.m including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete - with residual type petroleum bitumen of grade VG-10

CODE NO :12.20: Providing and laying pressed clay tiles (as per approved pattern 18mm nominal thickness of approved size) on roofs jointed with cement mortar 1:4 (1 cement : 4 coarse sand) mixed with 2% integral water proofing compound , laid over a bed of 20mm thick cement mortar 1:4 (1 cement : 4 coarsesand) and finished neat complete

CODE NO :12.20L: Lime concrete terracing on roofs of equired thickness laid to fall with 25mm nominal size brick aggregate and 50% lime mortar 1:2 (1 lime putty : 2 surkhi) rammed and finished with gur and belgiri treatment complete including rounding of junctions with Parapet wall complete

CODE NO :12.22: Making khurras 45x45cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20mm nominal size) over P.V.C. sheet 1m x1m x 400 micron , finished with 12 mm cement plaster 1:3 ( 1cement : 3 coarse sand) and a coat of neat cement , rounding the edges, making and finishing the outlet complete

CODE NO :18.9.14: Providing and fixing ASTM pipes including all ASTM plain& brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing . This includes jointing of pipes & fitting with one step ASTM solvent cement and testing of joints complete (Internal work exposed on wall ) - 40mm nominal outer dia pipes

CODE NO:12.41.2: Providing and fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS: 13592 Type A, including jointing with seal ring conforming to IS 5382, leaving 10mm gap for thermal expansion, (i) Single socketed pipes - 110 mm diameter

CODE NO:12.42.6.2: Providing and fixing on wall face unplasticised - PVC moulded fittings /accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion - shoe (plain) - 110mm shoe

CODE NO:12.43.2: Providing and fixing unplasticised - PVC pipe clips of approved design to unplasticised- PVC rain water pipes by means of 50x50x50mm hard wood plugs , screwed with M.S. screws of required length, including cutting brickwork and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand) and making good the wall etc., complete - 110mm

8.FINISHING: CODE NO:13.1.2: 12mm cement plaster of mix -1:6 ( 1 cement : 6 fine sand)

CODE NO:13.2.2: 15mm cement plaster on the rough side of single or half brick wall of mix - 1:6 (1cement : 6 fine sand)

CODE NO:13.7.1: 12mm cement plaster finished with a floating coat of neat cement of mix - 1:3 (1 cement :3 fine sand)

CODE NO:13.9.2: 20mm cement plaster 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement - 20mm cement plaster

CODE NO:13.9.1: Cement plaster 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement - 12mm cement plaster

CODE NO:13.16.1: 6mm cement plaster of mix -1:3 ( 1 cement : 3 fine sand)

CODE NO:13.21: Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers

CODE NO:13.37.1: White washing with lime to give an even shade - new work (three or more coats)

CODE NO:13.46.1: Finishing walls with acrylic smooth exterior paint of required shade - New work (two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg / 10 sqm

CODE NO:13.40: Distempeing with dry distemper of approved brand and manufacture (two or more coats) of required shade on new work, over and including water thinnable priming coat to give an even shade

CODE NO:13.50.1: Applying priming coat - with ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)

CODE NO:13.50.3: Applying priming coat - with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron / steel works

CODE NO:13.62.1: Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade - Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

CODE NO:13.84.2: Painting with synthetic enamel paint, having VOC (Volatile Organic Compound) content less than 150 grams / litre , of approved brand and manufacture , including applying additional coats wherever required to achive even shade and colour - Two coats

9.SANITARYINSTALLATION CODE NO:17.13.2: Providing and fixing white vitreous china water closet squatting pan (Indian type) -Orissa pattern W.C.pan of size 580x440mm

CODE NO:17.35.2.1:Providing and fixing soil,waste and vent pipes - 75mm dia - sand cast iron S&S pipe as per IS: 1729

CODE NO:19.33.1D: Providing and fixing on wall face / column face unplasticised - PVC mould fittings /accessories for unplasticisd - PVC soil and waste pipes conforming to IS : 14735 - 1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - bend with door 110 mm

CODE NO:12.42.4.2: Providing and fixing on wall face unplasticised - PVC moulded fittings /accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion - Single tee without door -110x110x110mm

CODE NO:1640: Slotted cowl (terminal guard)100mm dia

CODE NO:31.165.1G: Providing and fixing in position UPVC moulded unequal Tee (Finolex / jain)(0.6 Mpa) conforming to IS 7834 part II and ISI marked,including labour charges for jointing, jointing materials etc,complete - 110 x 63mm dia

CODE NO:12.42.4.1:Providing and fixing on wall face unplasticised - PVC moulded fittings /accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion - Single tee without door -75x75x75mm

CODE NO:19.33.2:Providing and fixing on wall/column face unplasticised - PVC soil and waste pipes (type B) conforming to IS:13592 - 1992 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - single socketed pipes 75mm diameter

CODE NO:19.38A.1: Providing and fixing stainless steel jali (grating) with or without hole for waste pipe for floor/Nahani trap - 75mm dia weight not less than 70 gms.

CODE NO:12.43.1: Providing and fixing unplasticised - PVC pipe clips of approved design to unplasticised- PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length, including cutting brickwork and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand) and making good the wall etc., complete - 75mm.

CODE NO:31.160.1J : Providing, laying and jointing UPVC pipes(Finolex / jain / Supreme / Truebore /Nandi) (1 Mpa)conforming to IS specification 4985 and ISI marked including transportation to the site , lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment,including cost of solvent cement,excluding UPVC specials such as bends,tees, threaded pieces , couplers, reducer ,endcaps ,complete all as per IS and CPWD pecification. - 140mm dia.

10.WATERSUPPLY CODE NO:18.9.15 : Providing and fixing ASTM pipes including all ASTM plain& brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing . This includes jointing of pipes & fitting with one step ASTM solvent cement and testing of joints complete (Internal work exposed on wall ) - 50mm nominal outer dia pipes

CODE NO:18.9.14 : Providing and fixing ASTM pipes including all ASTM plain& brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing . This includes jointing of pipes & fitting with one step ASTM solvent cement and testing of joints complete (Internal work exposed on wall ) - 40mm nominal outer dia pipes

CODE NO:18.9.13 : Providing and fixing ASTM pipes including all ASTM plain& brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing . This includes jointing of pipes & fitting with one step ASTM solvent cement and testing of joints complete (Internal work exposed on wall ) - 32mm nominal outer dia pipes

CODE NO:18.9.12 : Providing and fixing ASTM pipes including all ASTM plain& brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing . This includes jointing of pipes & fitting with one step ASTM solvent cement and testing of joints complete (Internal work exposed on wall ) - 25mm nominal outer dia pipes

CODE NO:18.9.11 : Providing and fixing ASTM pipes including all ASTM plain& brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing . This includes jointing of pipes & fitting with one step ASTM solvent cement and testing of joints complete (Internal work exposed on wall ) - 20mm nominal outer dia pipes

CODE NO:31.9.4: Providing and fixing brass gate valve with C.I. wheel of approved quality (screwed end) - 32mm nominal bore.

CODE NO:18.46.4: Providing and fixing G.I.union in G.I.pipe including cutting and threading the pipe and making long screws etc.complete (New work) - 32 mm nominal bore

CODE NO:18.15.1: Providing and fixing brass bib cock of approved quality - 15mm nominal bore

CODE NO:18.60.1:Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by Municipal board complete with bolts, nuts, rubber insertion etc .(The tail pieces if required will be paid separately) - 80mm dia nominal bore

CODE NO:18.18.3: Providing and fixing ball valve (brass) of approved quality , high or low pressure ,with plastic floats complete - 25mm ominal bore

CODE NO:18.20.3: Providing and fixing brass ferrule with C.I.mouth cover including boring and tapping the main - 25 mm nominal bore

CODE NO:18.48A: Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI: 12701 marked , with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank - Circular Tank

CODE NO:18.10.1: Providing and fixing G.I.pipes complete with G.I.fittings and clamps, including cutting and making good the walls etc -internal work -exposed on wall - 15mm dia nominal bore

CODE NO:18.46.2: Providing and fixing G.I.union in G.I.pipe including cutting and threading the pipe and making long screws etc.complete (New work) - 20 mm nominal bore

CODE NO:31.9.3: Providing and fixing brass gate valve with C.I. wheel of approved quality (screwed end) - 25mm nominal bore

CODE NO:18.46.5: Providing and fixing G.I.union in G.I.pipe including cutting and threading the pipe and making long screws etc.complete (New work) - 40 mm nominal bore

CODE NO:18.46.6: Providing and fixing G.I.union in G.I.pipe including cutting and threading the pipe and making long screws etc.complete (New work) - 50 mm nominal bore

DRAINAGE: CODE NO:32.35.1.2: Constructing brick masonry open surface drain with bricks of class designation 35 in cement mortar 1 : 4 (1 cement : 4 fine sand) including earth excavation, 10 cm thick bed concrete 1 : 5 : 10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 m nominal size and 25 mm thick cement concrete 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size) for filling haunches including 12 mm cement plaster 1 : 4 (1 cement : 4 coarse sand) with a floating coat of neat cement inside the drain, its top and exposed side including disposal of surplus earth complete as per standard design - 10 cm drain 20 cm average depth with class designation 35 bricks

CODE NO:19.18.1: Supplying and fixing C.I.cover without frame for manholes - 455 x 610 mm rectangular C.I.cover (light duty) weight of the cover to be not less than 23 kg

CODE NO:19.7.2.1: Constructing brick masonry manhole in cement mortar 1:4 (1 cement : 4 coarse sand) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ), foundtion concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand :4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design - inside size 120x90 cm and 90cm deep including C.I.cover with frame (medium duty) 500 mm internal diametre, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) - with common burnt clay F.P.S. (non modular ) bricks of classdesignation 7.5

CODE NO:1.1.2.2: Supplying and laying of following size of PVC conduit in roof slab alongwith the accessories .Make: Avonplast /Vijaya:- 25mm dia

CODE NO:1.1.2.1: Supplying and laying of following size of PVC conduit in roof slab alongwith the accessories .Make:Avonplast/Vijaya:- 20mm dia

CODE NO:1.1.3.1.4: Supplying and fixing of following size of PVC junction box in required position along the line of PVC conduit as required. Make:Avonplast/Vijaya:- 20mm Junction Box four way

CODE NO:31.160.1K Providing, laying and jointing UPVC pipes (Finolex / jain / Supreme / Truebore /Nandi) (1 Mpa)conforming to IS specification 4985 and ISI marked including transportation to the site, lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment,including cost of solvent cement,excluding UPVC specials such as bends,tees, threadedpieces, couplers, reducer, endcaps etc.,complete all as per IS and CPWD specification. - 160mm dia.

CODE NO:31.164.1N Providing and fixing in position UPVC moulded equal Tee (Finolex / jain)(0.6 Mpa) conforming to IS 7834 part II and ISI marked,including labour charges for jointing, jointing materials etc,complete - 160mm dia

CODE NO:31.167.1L Providing and fixing in position UPVC moulded reducer coupler (Finolex /jain)(0.6 Mpa) conforming to IS 7834 part II and ISI marked,including labour charges for jointing, jointing materials etc,complete - 160 x 110mm dia

CODE NO:31.173.1B Providing and fixing in position UPVC moulded saddle set (Finolex / jain)(0.6 Mpa) conforming to IS 7834 part II and ISI marked,including labour charges for jointing, jointing materials etc,complete - 75 x 20mm dia

CODE NO:16.96: Supplying fixing and commisioning of Suguna / Texmo / Sharp 2 HP monoblock pumpset slow speed single phase motor. The rate include the cost of pumpset , pumpset fixing in position and test run etc.complete

EZHILAN B