SPECIAL REPAIRS TO BLOCK NO P 106 OF TRIVENI COMPLEX AT MIL STAN JAMMU

Amount

Taking down chowkats or frames with shutter (without taking off shutter from the frame) n.exc 1.5 Sqm each including cutting holes for taking out hold fast or dismantling brick work and removing from site all as specified.

Taking down chowkats or frames with shutter (without taking off shutter from the frame) exc 1.5 Sqm & n.exc 4 Sqm each including cutting holes for taking out hold fast or dismantling brick work and removing from site all as specified.

Taking down shutters of any description exc 1.00 Sqm and n.exc. 2.00 sqm each and removing from the site all as specified & directed.

Taking down shutters of any description n.exc 1.00 Sqm each and removing from the site all as specified & directed.

Material & labour factory made steel windows and ventilators double shutter box type, outer frame made out of ERW TUBE 'P' section(65x45x25mm) and shutters of ERW TUBE 'P' section (50x35x20mm) operable shutters side hung includding pistol hinges with two Nos of MS Tower bolts 150mm size on each shutter steel handle and stopper of 'Z' section as specified complete with sash bars devetailed or welded ready for glass fixing and wire gauzed fixing with suitabel fittings/openning for cooler/AC where required. Steel windows will be double shutter external glazed and internal wire gauzed complete all as specifed and as per Drg No CEPZ/TD-324/07 1/3 to 3/3 all as specified and directed by Engr-in-Charge. NOTE: The quoted rate against the above item shall also include (i) for Provn of one shop coat of zinc chromate primer on all exposed steel surfaces and one coat of coal tar on the ends of steel frame in contact with brick/conc surface (ii) 04 Nos MS Steel lugs of 20x5mm MS flat 20cm long over all welded to frames (iii) PCC block for embedding lugs and all over flat iron all as per drg all as specified and as directed. (Grill measured separately)

Material & labour for pressed steel frame of size 105mm x 60mm made out of 1.25mm sheet for doors single rebated including mild steel hinges medium weight 100mm long and 25mm x 3mm flat iron in holdfast, tie bar including necessary fixing lugs, lock strike plate and fixing arrangement etc complete as specified and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-I complete all as specified and as directed.

Material & labour for pressed steel frame of size 125mm x 60mm made out of 1.25mm sheet for doors single rebated including mild steel hinges medium weight 100mm long and 25mm x 3mm flat iron in holdfast, tie bar including necessary fixing lugs, lock strike plate and fixing arrangement etc complete as specified and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-I complete all as specified and as directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm Plain colour PVC sheet reinforced with mild steel square tube, supplying and fixing in opening as per specifications and drawing including making good to disturbed surface of walls, complete all as specified and as directed by Engr-in-Charge.

M&L Pressed steel cup board frame of MS sheet 1.25 mm thick size of frame 60 x 40 mm with rebate of 20 mm wide and 12 mm deep including PCC 1:2:4 as in filling to back of chowkats including butt hinges 100 mm long. Piano hinges measured separately.

Supply and fixing Factory made, plain framed, panelled shutter (two Panel) 35mm thick, 2nd class Hardwood with lock rail and panel of 9 mm B.W.P commercial ply. The size of rail and stiles as per as per IS:1003 (Part-I), kiln seasoned and chemically pressure treated complete all as directed by Engr-in-Charge.

Supply and fixing 35mm thick 2nd Class hard wood glazed,gauzed and skelton shutters open rebated and prepare to receive glass, gauge etc but divided into squares with plain chamfered or rounded mitred and rebated sash bars,stiles and rails as specified in SSR Part-I Sec 8 clause 8.24 (a) complete all as specified

Material & labour 40 mm thick flush shutters, solid core construction core and plywood face panels, commercial ply on both sides.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppplying and fixing in the frame at site as per specification & drawing complete all as specified and as directed by Engr-in-Charge.

S&F Mild steel works of flat iron, square bar, round bars etc. as in framed work such as grills, guard bars, gratings etc incl bending, cutting and welding as necessary of confirming to Gde Fe 290-0 all as specified.

Repair to steel window, ventilators (including slot pin, hinge, hook and eye of standard quality where required), resecuring of windows wire gauge and railing/grills by using welding equipments complete all as directed.

Hacking out old broken glass (any thickness,size quality or description) from any types of wooden/steel/alum (up to 4th storey) frames or stone concrete or brick surrounds glazed with putty or fixed with beads.

S&F 4 mm thick sheet glass ordinary quality glazing with oil putty or any type of beads in square n.exc. 0.5 Sq each pane in any type of frame of iron/Steel/Wood/Aluminium as required at site complete all as specified (upto fourth storey with necessary scaffolding), all as specified.

S&F 4 mm thick figured glass, pin head type and glazing with oil putty or any type of beads in square n.exc. 0.5 Sq each pane in any type of frame of iron/Steel/Wood/Aluminium as required at site complete all as specified (upto fourth storey with necessary scaffolding), all as specified.

Supply and fixing stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm complete all as specified fixed with stainless steel wire staples.

Supply and fixing in repair stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm complete all as specified fixed with stainless steel wire staples.

Material & labour for 18/19 mm thick ply wood as in shutters/shelves etc exterior grade prelaminated one side with decorative choice lamination and other side balancing white lamination fixed to frame work with screws to etc. complete all as specified and directed.

S&F in repair 25mm outer dia stainless steel decorative drapery rod of thickness 20 gauge and for every 01 RM length, with stainless steel brackets near to ends with stainless steel finials for 25mm dia drapery rod at both ends. The drapery rod shall be projecting 150 mm outer side from the clear opening of doors/windows. ( Including necessary fittings)

Supply and fixing mild steel helical ordinary rat tail rod pattern springs 300mm including roller and roller plate complete including fixing to pressed steel frames necessary welding work all as specified and as directed.

Supply and fixing in repair mild steel helical ordinary rat tail rod pattern springs 300mm including roller and roller plate complete including fixing to pressed steel frames necessary welding work all as specified and as directed.

S&F in repair continuous (piano) hinges 300mm, heavy duty mild steel, bright finish or electro galvanised sutable for 19mm thick shutter and fixed, complete all as specified. ( ISI Marked)

S&F butt hinges of mild steel cold rolled medium weight of size 100mm as specified.

Supply and fixing for stainless steel Butt hinges, 100mm , complete all as specified and as directed

S&F Aluminium anodised, barrel tower bolts size 150 mm of extruded section and fixed complete all as specified. (ISI Marked)

S&F Aluminium handles,fabricated type, anodised Size-150mm, anodised section and fixed complete all as specified. (ISI Marked)

S&F Aluminium alloy, anodised, sliding door bolt Size- 250 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified.

S&F hasp & staple safety type aluminium anodised with mild steel hinges Spin including bolt to hinges plate fixed with screws of 75 mm in length.

S&F aluminium hanging floor door stopper,Twin rubber stopper,size 100mm , anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

M&L for 50 mm magnetic catches with brass body and striking plate including letting in as fixed complete all as specified and directed.

S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified. ( ISI Marked)

Securing glass of any description in existing wooden and iron frames glazed with putty/beads including removing loose or decayed putty/beads, painting/oiling one coat on rebates, grooves, reputtying and painting/oiling puttied surface to match existing work ( New length of frame reputtied shall be measured.

M&L in repair for Welding in repairs n. exc 2.5cm in length, thickness of metal to be welded exc 6mm but n exc 9mm, complete all as specified and direcetd by Engineer-in-charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding, terrazo dado from wall surface (but not backing), removing serviceable tiles to store and rubbish off the premises. Complete all as specied and directed.

Material and labour Vitrified Ceramic double charged edge cut joint free coloured or printed any shade tiles 8 to 10 mm thick (square/ rectangular) polished area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured/white cement to match over and including 15 mm thick screed bed in CM 1:4. (Sample as approved & Kept in GE's sample room)

Description all as item No 38 but as in vertical surfaces dado/skirting over and including a backing coat of CM 1:4, 10 mm thick complete.

Material and labour Non - skid Digital Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured/white cement to match the surface over and including 15 mm thick screed bed in CM 1:4. ( sample as approved & kept in GE's sample room)

Description all as item No 40 but as in vertical surfaces dado/skirting over and including a backing coat of CM 1:4, 10 mm thick complete.

Material and labour glazed ceramic coloured Digital tiles in vertical surface 300x450x7 mm thick, set and jointed in neat cement slurry and pointed white or colored cement to match the surface over and including 10 mm thick CM 1:4 all as specified. (Sample as approved & Kept in GE's sample room)

M&L 16 to 18 mm thick Granite work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with granite and cutting holes foe gas pipe wherever required over and including 15 mm thick CM 1:4 as directed by Engr-in-charge.

M&L Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified.

Complete removal of the existing water proofing treatment of any description including under layer, taking down of cement plater,brick layer/demolition of cement concrete any thickness and removal of debris off the premises including grubbing up of tree roots and preparation of concrete surfaces by scrubbing down with steel brushes and cleaning with water to remove to all loose dirt/dust and applying the following Roof Treatment as below :-(i) Rendering 15 mm thick in CM 1:4 mixed with integral water proofing compound on concrete surface in roofs incl applying cement slurry @ 3 Kg per Sqm finishing even and fair without using extra cement (WPA shall be measured separately) .(ii) Applying a coat of bitumen primer membrane 0.4 ltr/sqm by the same membrane manufacturer of density at 25 degree C 0.87-0.89 kg/ltr and viscosity 70-160 CPS till the surface properly impregnates and insolvent oil primer evaporates completely (iii) Applying polymeric polypropylene polymer membrane 'APP' (atactic polypropylene polymer) modified prefbricated five layer 3 mm thick not less than 3.60 kg/sqm with 160 gms/sqm non woven polyester made at centre core reinforced laidwith 75 mm side overlap and 100 mm over laps which shall be thermo fused by flame (iv) Applying course of two coats of aluminium paint over the APP membrane all as specified. complete all as specified and as directed.

Supply only Liquid water proofing compound complete all as specified and as directed of as per manufacturer instruction.

Complete removal of mud pushka from the roof of the building and removing from the roof to ground complete and washing and rubbing down with water and preparing the surfaces for water proofing treatment complete all as specified and as directed. all as specified.

Removing excavated material exc. 1.50 km but n exc. 5 km and depositing where directed

M&L for cement concrete type B-0 (1:2:4) 12.5 mm graded stone aggregate as in roof padding/floor finish all as specified and as directed.

Dismantling and Re- fixing and Rotational moulded polyethylene water storage tanks of 500 litres capacity, (cylindrical vertical with closed top) triple layered, white, hoisted and fixed in position incl cleaning all as specified in SSR Part-I including making connections complete all as specified

Dismantling and Re- fixing Rotational moulded polyethylene water storage tanks of 1000 litres capacity, (cylindrical vertical with closed top) triple layered, white, hoisted and fixed in position all as specified in SSR Part-I including making connections complete all as specified

S&F in repair Gun metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed, Bore dia of 20mm complete all as specified and as directed.

S&F in repair Gun metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed, Bore dia of 25mm complete all as specified and as directed.

Supply and fixing in repair Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe of 20 mm bore pipe including making connections complete all as as specified and fixed (Minimum weight 20mm-210 gms).

Demolition of cement concrete of any description and in any position and Removing excavated material in up to 1.50 km and depositing where directed at a level not exceeding 1.5m above the starting point all as specified etc complete.

Demolition of Re inforced cement concrete of any description and in any position and Removing excavated material in up to 1.50 km and depositing where directed at a level not exceeding 1.5m above the starting point all as specified etc complete.

Taking up or down steel tubing of 15 mm bore pipe and connections, including cleaning for re-fixing or removal to store complete all as specified and as directed.

Taking up or down steel tubing of 20 mm bore pipe and connections, including cleaning for re-fixing or removal to store complete all as specified and as directed.

Taking up or down steel tubing of 25 mm bore pipe and connections, including cleaning for re-fixing or removal to store, complete all as specified and as directed

Supply and fixing 20 mm nominal outer dia Chlorinated Polyvinyl Chloride (CPVC) pipes SDR 11, having thermal stability for hot & cold water supply, including all Plain CPVC SDR 11 fittings & brass threaded fittings on walls/ceiling or laying in floors,including fixing the pipe with clamps. This includes jointing of pipes & fittings with one step CPVC solvent cement, complete as per direction of Engineer in Charge.

Supply and fixing GI tubes 'medium grade' galvanised, 15 mm bore, ISI marked with all fitting such as bends, tees,elbows, unions,short pieces, connectors, back nuts etc and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

Supply and fixing GI tubes 'medium grade' galvanised, 20 mm bore, ISI marked with all fitting such as bends, tees,elbows, unions,short pieces, connectors, back nuts etc and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

Supply and fixing tubes 'medium grade' galvanised, 25 mm bore, ISI marked with all fitting such as bends, tees,elbows, unions, short pieces, connectors, back nuts etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed.

Refixing old steel tubing galvanised, 25 mm bore with all fitting such as bends, tees,elbows, unions, short pieces, connections, back nuts and connection in new or old position (walls, ceiling, floors etc.)

S&F in repair stop/angle valve with wall flange, cast copper alloy, chromium plated fancy type screwed for 15 mm iron pipe, complete all as specified.

S&F in repair Bib Cock with Wall Flange cast copper alloy, chromium plated fancy type screwed with wall flange sutable for iron pipe, 15 mm bore complete all as specified.

&F in repairs exposed part kit of concealed stop cock fancy type, chromium plated with shank and cup complete all as specified and as directed.

S&F in repairs chromium plated shower rose 125mm square size with arm 15mm dia 195mm long with bend 45 degree with brass flange, complete all as specified and directed.

S&F in repair PVC connection 15 mm x 450 mm including PTMT check nut at both ends screwed for iron pipe of 15 mm bore.

S&F in repairs grating doom dia 100 mm fixed with white cement all as specified.

Supply and fixing in repair sinks made of stainless steel 1.00 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915 mm x 46mm, bowl size 410mm x 330mm x 160mm complete with waste coupling & PVC waste pipe complete all as specified and directed by Engineer-in-charge.

S&F in repair Vitreous China, wash basin white, flat back , size 550mmx400 including pedastal full length and brackets of any size, including cutting for and pinning in ends of brackets or erecting stand including fixing and supply of waste pipe of 32 mm dia, waste coupling of chromium plated brass complete all as specified and as directed by Engineer-in-charge..

S&F in repair PVC valveless, syphonic action type, flushing cistern, low level,white with inlet, ball valve, float and handle including brackets, PVC 32 mm 'L' bend of capacity 10.0 litres and making good to dismantled/damaged floor/surfaces, fixing in repair, complete all as specified and as directed by Engineer-in-charge.

S&F in repair WC Orissa pattern white with integral foot rest 580x 440 mm including L bend, & PCC bedding in 1:2:4 and making good disturbed floor connecting to trap and flush pipe compete all as specified. (Rate of including in taking out and removal of old WC seat unhygienic condition)

Supply and fixing in repair Vitreous china ware pedestal type water closet white, with 'P' or 'S' trap including self closing seat cover, closed pattern with flat bottom, complete all as directed.

Dismantling PVC/Cement/CI pipes 50 to 110 mm dia including all fittings like bend,branch pieces, connectors, heel rest bend etc and removing from site all as specified and directed

Supply and fixing UPVC (SWR) type B pipes 110 mm bore single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing UPVC (SWR) type B pipes 110 mm bore single socketed, in any length with rubber ring joints fixed to walls including stack clamp of GI flat 30mm wide 2mm thick fixed to wall with nail at spacing of 1m center to center, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing UPVC (SWR) type B pipes 75 mm bore single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing UPVC(SWR) type B pipes 75 mm bore single socketed, in any length with rubber ring joints fixed to walls including stack clamp of GI flat 30mm wide 2mm thick fixed to wall with nail at spacing of 1m center to center ,complete all as specified and as directed by Engineer-in-charge.

Supply and fixing, UPVC (SWR) , bends with access door for 75 mm bore , complete all as specified and as directed by Engineer-in-charge.

Supply and fixing, UPVC(SWR) , bends with access door, for 110 mm bore complete all as specified and as directed by Engineer-in-charge.

Supply and fixing, UPVC(SWR), junction single, (single 'T') with access door equal or unequal for 75 mm bore , complete all as specified and as directed by Engineer-in-charge.

Supply and fixing, UPVC(SWR), junction single, (single 'T') with access door equal or unequal for 110 mm bore , complete all as specified and as directed by Engineer-in-charge.

Supply and fixing UPVC type B branch piece single 'Y' equal or unequal for 110mm bore with ovel access door (ISI Marked).

Supply and fixing UPVC type B branch piece single 'Y' equal or unequal for 75mm bore with ovel access door (ISI Marked).

Supply and fixing, UPVC (SWR) , bends for 75 mm bore , complete all as specified and as directed by Engineer-in-charge.

Supply and fixing, UPVC(SWR) , bends for 110 mm bore complete all as specified and as directed by Engineer-in-charge.

S&F in repair, UPVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified.

Supply and fixing in repair UPVC (SWR) floor trap plain with grating having dia meter of out let 75mm including jointing with solvent cement to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&F UPVC (SWR) vent cowl 75 mm dia complete all as specified.

Demolition of brick work built in cement mortar including all quoin, arches pillars but excluding ashlar facing dressed stone work and precast concrete article complete all as specified and as directed.

M&L for Brick work with subclass 'B' bricks, old size bricks, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified and as directed.

M&L for Brick work with subclass 'B' bricks, old size bricks, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 but except bricks complete all as specified and as directed.

M&L for Brick work with subclass 'B' bricks, old size bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed.

Taking down cement plaster on brick or stone walls or stone walls etc, including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and as directed. (Note :- Work will be carried out up to 4th storey with necessary scaffolding).

Material and labour for rendering 15 mm thick on fair faces of brick or concrete surface walls, in cement mortar 1:4 , rendering is to be finished even and smooth without using extra cement (up to 4th storey with necessary scaffolding complete all as specified and as directed by Engineer-in-charge.

Material and labour rendering 15 mm thick on fair faces of brick or concrete surface walls, in cement mortar 1:6 , rendering is to be finished even and smooth without using extra cement complete all as specified and as directed.

M&L for preparation of new plastered surfaces of walls & applying two coats of oil bound distemper over one coat of wall care putty of 1 to 2 mm thick and one coat of primer complete all as specified and as directed.

Material and labour for applying two coats of oil bound distemper on old surfaces of walls over 1 to 2 mm thick wall care putty including preparation of surfces complete all as specified.

Ditto all as per item No 100 but on ceiling

Preparation of old decorated brick/concrete/ plastered/unplastered surfaces of walls, Pillars, cornices etc by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots, rubbing with sand paper and applying one coat of cement base paint on walls, pillars, cornice etc (upto 4th storey with necessary scaffolding complete all as specified and directed.

M&L for preparation of new plastered/ concrete surfaces of walls to achieve smooth and even surface and applying two coats of cement base paint over and including one coat of primer (up to 4th storey with necessary scaffolding) .

M&L for applying two coat of synthetic enamel paint over a coat of red oxide primer on new steel surfaces of any description having width/girth exceeding 10 cm including preparation and rubbing with sand paper to make surface even and smooth complete all as specified.

M&L for applying one coat of synthetic enamel paint on old painted steel surfaces of any description having width/girth exceeding 10 cm including preparation and rubbing with sand paper to make surface even and smooth and primer where requred complete all as specified.

M&L for applying two coat of synthetic enamel paint on new wooden surfaces of any description over a coat of pink primer having width/girth exceeding 10 cm complete all as specified including preparation and necessary filling by chalk putty as and where requered to make surface even and smooth.

M&L for applying one coat of synthetic enamel paint on old painted wood surfaces of any description having width/girth exceeding 10 cm complete all as specified including preparation and where requered to make surface even and smooth.

Complete removal of existing treatment including washing, rubbing down with sand paper and stopping of painted surfaces including preparation of old plastered surfaces of walls, chajjas, fascia, face of columns, beams etc. and applying one coat of weather proof exterior emulsion making good uneven surface/holes with Birla wall care putty coloured in same shade where ever required etc (up to 4th storey with necessary scaffolding) complete all as specified and directed.

M&L Rendering 15mm thck in CM 1:3 or Plain Cement Concrete as in sunken floors without extra cement on walls/floors and including mixing of water proofing compound (WPC shall be measured and paid separately)

M&L applying a coat of bituminous primer conforming to IS-3384 on prepared surface of roof/sunken slab after drying of primer apply APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyester non woven fabric (wt not less than 150 gms/sqm) laid on primed surface by forced torched application and finally apply a coat of hot blown 85/25 graded bitumen conforming to IS-702 @ 1.2kg /sqm of plaster surface.

M&L Cement concrete type E-2, 1:5:10 ( 40 mm graded agregate) in Sunkan ( Up to 4th floor) filling and mass concrete complete all as specified and directed by Emgr-in-charge.

M&L 40 mm dia G I tubing heavy grade galvanised laid over floors as a spout pipe in sunken floors all as specified.

S&F in repair Central Hole Basin Mixer without Popup Waste System with 450mm Long Braided Hoses Also available all as per directed and specified.

Supply and fixing in repair wall mixer non telephonic shower arrangement with connecting legs and wall flanges, cast copper alloy, chromium plated, complete all as specified.

S&F in repair Sink Cock with Swinging Spout (Wall Mounted Model) with Wall Flange complete all as specified.

S&F in repair Sink Mixer with Swinging Spout (Wall Mounted Model) with Connecting Legs & Wall Flanges complete all as specified.

S&F in repair Chromium plated hand shower (health faucet) with 8mm dia 1.20m long flexible tube and wall hook, complete all as specified.

Material and labour for plain cement concret 1:2:4 type B-0 in coping, kerb, hunhing or siilar work without using extra cement finished even and fair including necessory formwork and scaffolding complete all as specified and directed. (Up to fourth storey bldg and including formwork and scaffolding reduired as per site conditions).

S&F in repair Glass shelf 600mm long, complete all as specified.

S&F in repair Corner Glass Shelf (with Bracket) as per directed by Engr-in-charge.

S&F in repairs tubular towel rail 60 cm brass chromium plated dia all as specified.

S&F factory made 18mm(+0.7mm) thick celuka PVC ply of density 600Kg/cbm manufacured by an ISO 900-2008 certified company. One side glossy finish prelam and other side plain18mm thick Celuka PVC ply for cabinet shutter and also manufactuer's test report and test certificate is mandatory with each and every supply of the material complete as per manufacturer's specifications and drawing and as directed.

S&F factory made 18mm(+0.7mm) thick celuka PVC ply of density 600Kg/cbm manufacured by an ISO 900-2008 certified company. Plain 18mm thick Celuka PVC Ply for Shelf/Partitions /Drawer and also manufacturer's test report and test certificate is mandatory with each and every supply of the material complete as per manufacturer's specifications and drawing and as directed.

S&F factory made 5mm thick PVC of density 600Kg/cbm manufacured by an ISO 900-2008 certified company. Plain 5mm thick PVC sheet paneling for back side (wall side) and also manufacurer's test report and test certificate is mandotary with each and every supply of the material complete as per manufacturer's specifications and drawing and as directed.

S&F telescopic heavy duty drawer channels soft closer of size 450m length (In closed position) fixed in PVC ply with brass screws as in drawers complete all as specified and as directed.

S&F Auto hinges of size 150mm length fixed in cupboards with screws for holding stainless steel brackets complete all as specified and as directed.

S&F steel fastners of size 75mm long drilled and fixed to walls complete all as specified and as directed.

M&L for repairing of concrete surfaces such as balconey, chajjas, upward or downward facias, column, Piller, ceiling and similar items with plain cement concret 1:2:4 type B-0 & rendering any thickiness in CM 1:3 without using extra cement finished even and fair complete all as specified and directed and including necssory formwork and scaffolding required as per site conditions and welding if necessary and re inforcement complete all as specified and as directed.

Cutting holes into or through brick walls built in cement mortar for ventilator as in circular and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required exc 400 sqcm and n exc 1000 sqcm all as specified and as directed.

S&F stainless steel fancy type handles 100 mm fixed with wooden/pvc boards al as specified and as directed.

S & F Kitchen stainless steel plate rack made out of 1 mm thick sheet and having partions as per sample. The over all size (30"x36"x10") fixed with steel fastners or steel screw complete.

M/S PARAMJEET SINGH

AKSHAY CONSTRUCTION COMPANY

Continental Enterprises