REPAIR MAINT OF HOT WATER APPLIANCES, SOLAR WATER HEATER AND ALLIED WORKS IN ZONE C AND D UNDER AGE (I) AYODHYA CANTT

Amount

Taking down existing defective electric geysers of any make and any capacity (25/50 Ltr) vertical OR horizontal from its location servicing by disconnecting all electrical and incomming / outgoing pipe connections, cleaning of tank after opening of its assembly at site, cleaning of assembly pipe to avoid its choke up, checking of defective parts, necessary repair and replacement of defective parts (to be measured separately) to make the geyser fully functional to the entire satisfaction of Engineer-in- Charge and refixing the geyser in its original position including re-connecting all electrical and pipe line connectons, testing and commissioning complete all as specified and directed. Note :- (i) The contractor or his authorised rep will receive the Geyser complaints daily from MES service cell and attend the user's complaints as directed by JE E/M or Engr-in-Charge. (ii) Day to dy complaints shall be completed within 24 Hours, failing which a penalty @ Rs. 400.00 per complaint per day of dealy from receipt of complaint to actual date of completion of the complaint shall be imposed on the contractor. (iii) All T&P and minor spare parts such as screws, nuts & bolts, washers, emery papers, waste cloths / cotton etc shall be provided by the contractor and the cost of the same to be deemed included in the quoted rates. (iv) The defective parts replaced with new one shall be measured and paid for separately against relevant item of Schedule 'A'/BOQ.

S&F in replacement, Heating element threaded/ screwed/ triangular or cup style type 2000 Watt ISI marked of suitable make without taking down Geyser complete all as specified and directed by Engineer-in-Charge.

S&F in replacement, thermostat suitable for 25 or 50 litre capacity of geyser, range 20 to 80 degree ISI marked, without taking down geyser complete all as specified and directed by Engineer-in-Charge.

S&F in replacement, indicator lamp assembly with bulb suitable for geysers round or square type of approved make and quality as approved, without taking down geyser complete all as specified and directed by Engineer-in-Charge.

S&F in replacement, PVC connection cotton braided heavy duty with brass union/ coupling of length 450 mm with rubber washer suitable for 15 mm dia pipe for hot or cold water connection, without taking down geyser complete all as specified and directed by Engineer-in-Charge.

S&F in replacement, PVC connection cotton braided heavy duty with brass union/ coupling of length 900 mm with rubber washer suitable for 15 mm dia pipe for hot or cold water connection, without taking down geyser complete all as specified and directed by Engineer-in-Charge.

S&F in replacement, housing assembly for 25 Ltr Capacity ISI marked complete all as specified and directed by Engineer-in-Charge.

S&F in replacement, safety valve (dead plug) small ISI marked complete all as specified and directed by Engineer-in-Charge.

S&F in replacement, safety valve (pressure release valve) ISI marked complete all as specified and directed by Engineer-in-Charge.

S&F in replacement, gasket for 25 Ltr Capacity assembly ISI marked complete all as specified and directed by Engineer-in-Charge.

S&F in replacement, gasket for 50 Ltr Capacity assembly ISI marked complete all as specified and directed by Engineer-in-Charge.

S&F in replacement, inner tank made of MS 1.6 mm thick suitable for 25 litre capacity geyser, complete all as specified and directed by Engineer-in-Charge.

M&L for preparing old painted surfaces of geysers at site (without taking down) of 25 Ltrs capacity and applying one coat of synthetic enamel paint with spray gun including re-writing or marking of MES No. with black paint in appropriate size complete all as specified and directed by Engineer-in-Charge.

M&L for preparing old painted surfaces of geysers at site (without taking down) of 50 Ltrs capacity and applying one coat of synthetic enamel paint with spray gun including re-writing or marking of MES No. with black paint in appropriate size complete all as specified and directed by Engineer-in-Charge.

S&F in replacement, bottom cover for geyser in two pieces made of GI sheet in required/ existing size and shape suitable for 25 / 50 litres capacity geyser including painting with two coats of synthetic enamel paint over a coat of primer to match the existing surfaces of geyser complete all as specified and directed by Engineer-in-Charge.

M&L for repairs to leakage of inner tank of 25/50 litre capacity geyser by brazing or soldering including cutting of nuts, bolts, washers etc, as required with gas welding cutter and provinding new nuts, bolts, washers etc including testing of leakage of tanks after repair, complete all as specified and directed by Engineer-in-Charge.

S&F in replacement, Anchor bolts 5" long with nut and washers including drilling holes in existing wall for fixing anchor bolt and making good the disturbed surfaces of wall to match the existing surfaces complete all as specified and directed by Engineer-in-Charge.

S&F in replacement, 25mm dia bore galvanised iron tubing, medium grade, with all fittings & fixed to walls, ceilings or laid in floors complete all as specified and directed by Engineer-in-Charge.

S&F in repairs, 25mm dia bore stop valves, brass chromium plated, concealed type, screwed both ends for pipes or for unions, including making good the disturbed surfaces to match the existing surfaces complete all as specified and directed by Engineer-in-Charge.

S&F in repairs, plug top 3 pin,15 Amps (ISI marked) complete all as specified and directed by Engineer-in-Charge.

Dismantling solar water heating system panel of 300 litres capacity of any make and type by removing the glass panel carefully and re-fixing the same after cleaning dust, cleaning of water collector tubes and aluminium foil including descaling the existing hot water storage tank of any capacity and replacement of rock wool complete all as specified and directed by Engineer-in-Charge.

S&F in replacement, 300 Ltrs capacity PUF insulated tank (ISI marked), suitable for flat plate collector system c complete all as specified and directed by Engineer-in-Charge.

S&F in replacement, MS powder coated stand (ISI marked) for 300 Ltrs tank of flat plate collector system complete all as specified ISI marked complete all as specified and directed by Engineer-in-Charge.

S&F in replacement, solar flat plate collector (ISI marked) of 300 LPD capacity complete all as specified and directed by Engineer-in-Charge.

S&F in replacement, collector to tank inter connecting synthetic rubber hose suitable for flat plate collector system of 300 LPD capacity complete all as specified and directed by Engineer-in-Charge.

S&F in replacement, hose clip suitable for flat plate collector system of 300 LPD capacity complete all as specified and directed by Engineer-in-Charge.

S&F in replacement, EPDM gasket with centre hole (ISI marked) suitable for flat plate collector system of 300 LPD capacity complete all as specified and directed by Engineer-in-Charge.

S&F in replacement, dummy gasket (ISI marked) suitable for flat plate collector system of 300 LPD capacity complete all as specified and directed by Engineer-in-Charge.

S&F in replacement, dummy flange (ISI marked) suitable for flat plate collector system of 300 LPD capacity complete all as specified and directed by Engineer-in-Charge.

S&F in replacement, M6x25MM SS-304 nut & bolt with flat and spring washer (ISI marked) suitable for flat plate collector system of 300 LPD capacity complete all as specified and directed by Engineer-in-Charge.

S&F in replacement, 13x8 PAN head screw suitable for flat plate collector system of 300 LPD capacity complete all as specified and directed by Engineer-in-Charge.

S&F in replacement, 58mm (D) x 1800mm (L) vacuum glass tube (ISI marked) suitable for evacuated tube collector system of 100 LPD capacity complete all as specified and directed by Engineer-in-Charge.

S&F in replacement, neoprene gasket (58ID) (ISI marked) suitable for evacuated tube collector system of 100 LPD capacity complete all as specified and directed by Engineer-in-Charge.

S&F in replacement, tube holder plastic (ISI marked) suitable for evacuated tube collector system of 100 LPD capacity complete all as specified and directed by Engineer-in-Charge.

S&F in replacement, black rubber ring suitable for evacuated tube collector system of 100 LPD capacity complete all as specified and directed by Engineer-in-Charge.

S&F in replacement, electrical back-up heater with inbuilt thermostat 2 KW (ISI marked) suitable for flat plate collector / evacuated tube collector system of 300 LPD capacity complete all as specified and directed by Engineer-in-Charge.

S&F in replacement, 20 mm dia heat proof (pre-insulated ) composit pipe (ISI marked) for hot water distribution line with all fittings and fixed to wall or ceiling / floor complete all as specified complete all as specified and directed by Engineer-in-Charge.

S&F in replacement, 25 mm dia heat proof (pre-insulated ) composit pipe (ISI marked) for hot water distribution line with all fittings and fixed to wall or ceiling / floor complete all as specified complete all as specified and directed by Engineer-in-Charge.

S&F in replacement, 20mm dia bore gun-metal globe or gate valves with iron wheel head, screwed both ends of iron pipe complete all as specified and directed by Engineer-in-Charge.

S&F in replacement, 25mm dia bore gun-metal globe or gate valves with iron wheel head, screwed both ends of iron pipe complete all as specified and directed by Engineer-in-Charge.

M&L for cleaning and descaling of water circulation system of rotational moulded polyethyline water storage tank upto 500 ltrs capacity (cylindrical vertical with closed top) complete all as specified and directed by Engineer-in-Charge.

S&F in replacement, 20mm dia bore ball brass valves, high pressure with polythene float and flynut, screwed for iron pipe or brass ferrule complete all as specified and directed by Engineer-in-Charge.

S&F in replacement, 25mm dia bore ball brass valves, high pressure with polythene float and flynut, screwed for iron pipe or brass ferrule complete all as specified and directed by Engineer-in-Charge.

Jairajyadav security services

VIDYA TRADERS

M/s Hanspal Enterprises