SPECIAL REPAIRS TO BLDG NO P 38 FOR IFS 5 LAB AT ADE UNDER GE I RND EAST BANGALORE

Amount

Demolition of cement concrete manually / by mechanical means including disposal of materIal within 50 metres, complete all as specified and directed.

M&L for cement concrete 1:2:4 (1 cement : 2 coarse sand derived from natural sources : 4 graded stone aggregate of 40 mm nominal size) as in roof concrete complete all as specified and directed.

M&L for 10mm thick cement plaster in CM 1:3 over roof concrete surface and finishing the surface even and smooth with using water proofing compound complete all as specified and directed. Note: WPC shall be measured and paid separately.

M&L for Providing and mixing water proofing material in cement per bag of plaster work in proportion recommended by the manufacturer complete all as specified and directed.

Cutting V grooves 15mm x 15mm in existing roof or terrace and cleaning out and filling / making good with epoxy based compound NITOMARTAR PE of FOSROC chemicals complete all as specified and directed.

Material and Labour for providing the sealant (pouring grade) in the existing 10mm wide & 40mm deep groove / joint after preparation of joints as per manufacture instructions along with application of primer complete all as specified and directed. (a) Thioflex 600 shall be of M/s FOSROC/ MASTERFLEX TM 700i of BASF or equivalent in CIPY. (b) Primer 7E shall be M/s FOSROC or equivalent in BASF / CIPY. Note: Application of Epoxy and sealant shall be carried out by authorised applicator of manufacture.

M&L for Polyurethane based chemical treatment as to be laid as under: (a) Mechanical cleaning of surface to make it free from any bituminous residue / dirt oil and greece etc all as specified and directed. (b) Cracks treatment by cutting open cracks and cleaning it from dirt / loose materials etc and filling with polyurethane based sealant with and including application of PU based primer all as directed. (c) Applying water based polyurethane modified dispersion (single component, cold applied, non toxic, VOC complaint) in 03 coats including 01 coat of primer of same material as per manufacturer specification and as directed. A layer of geotextile grid of minimum 40 gsm sandwich in between two PU layers as per manufacturers specification be provided, complete all as specified and directed.

Properties of Polyurethane based chemical shall confirm to following technical parameters:- (i) Highly elastic, (ii) UV resistance, (iii) Adhesion to concrete>1 N/Sqmm, (iv) Tensile strength not less than 2.0 N/Sqmm for free film, (v) Elongation not less than 300%, (vi) Solid content by weight not less than 60%, (vii) Air / water permeability BSEN 12390 at 5 bar - 72 hours should be NIL and minimum dry film thickness of water proofing membrane must be 1.0mm. (viii) Accelerated weathering (ASTM 453): Pass 1000 Hours, (ix) Reaction to fire, non-inflammable. Notes : 1. To be applied by the rep of manufacturers authorised applicator only. Contractor has to provide manufacturer's test certificate for the above mentioned Technical parameters and purchase voucher. 2. Removal of existing treatment to be paid separately. 3. Roof slop to be ensured to avoid water ponding. 4. For accessible terrace and in-accessible terrace, 300 mm height of vertical surface / parapet wall to be treated with same specification of slab.

Dismantling tiles, wall tiles only and roofs laid in cement mortar including stacking material within 50 metres lead for thickness of tiles 10 mm to 25 mm complete all as specified and directed.

M&L for 25mm average thick Cement concrete flooring 1:2:4 (1 cement : 2 coarse : 4 graded stone aggregate) finished, including cement slurry, but excluding the cost of nosing of steps etc. complete all as specified and directed.

M&L for Double Charged Vitrified floor tiles of size 600mm x 600mm x 10mm thick with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid over and including 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 Kg/Sqm including grouting the joints with white cement and matching pigments etc complete all as specified and directed.

All as per item No 10 here-in-before but as in skirting including 12mm thick screed bed in CM 1:3 complete all as specified and directed.

M&L for providng and laying Ceramic glazed floor tiles of size 300 x 300 mm, 7 to 8 mm thickness of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid over and including 20 mm thick bed of cement mortar 1:4 (1 cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 Kg/Sq.m including pointing the joints with white cement complete all as specified and directed.

M&L for Providing and fixing 1st quality Coloured glazed ceramic tiles of size 450mm x 300mm / 450mm x 350mm, 7 to 8 mm thickness in dado / skirting etc., conforming to IS : 15622 of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over and including 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 Kg/Sq.m including pointing in white cement with pigment of matching shade complete all as specified and directed.

M&L for 50mm thick plinth protection of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over and including 75 mm thick bed of dry stone ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top, smooth complete all as specified and directed.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead complete all as specified and directed.

M&L for 15 mm thick plaster in CM 1:4 on fair faces of walls, finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for 10 mm thick internal plaster in CM 1:6 on other than fair faces of walls, finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for 5 mm thick plaster in CM 1:4, as in ceiling, finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of plastered or unplastered surface & Distempering 02 coats with oil bound washable distemper of approved brand manufacture to give an even shade over and including water thinnable priming coat with cement primer complete all as specified and directed.

All as per item No 19 here in before but on old surfaces after and including complete removal of existing treatment of any type and condition complete all as specified and directed.

M&L for finishing walls with 100% Premium acrylic external emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS : 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with sillicon additives. New work (Two coats applied @ 1.43 litre/ 10 Sq.m over and including priming coat of exterior primer applied @ 0.90 litre / 10 Sq.m complete all as specified and directed.

M&L for finishing walls with 100% Premium acrylic external emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS : 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with sillicon additives. New work (Two coats applied @ 1.43 litre/ 10 Sq.m over and including priming coat of exterior primer applied @ 0.90 litre / 10 Sq.m on old surface of walls complete all as specified and directed.

M&L for preparing of new plastering surface of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for preparing old ceiling surface and applying two coats of white wash complete all as specified and directed.

M&L for painting steel surface with synthetic enamel paint of approved brand and manufacture to give an even shade of Two coats on new work / old surface complete all as specified and directed.

Material and labour for preparation of old/ new wooden surfaces Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two coats on new work complete all as specified and directed.

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead of area 3 Sq.m and below each complete all as specified and directed.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave holdfasts etc., complete and stacking within 50 metres lead of area 3 Sq.m and below each complete all as specified and directed.

Taking out existing wooden door shutter, repair by cutting, painting etc., and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws etc., complete all as specified and directed.

M&L for providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with requires EPDM rubber / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings complete all as specified and directed. Note: Glazing, panelling and dash fasteners to be paid for separately.

M&L for providing and fixing 4mm thick float glass panes of 4.0 mm thickness (weight not less than 10 Kg/Sq.m) glazing in aluminium door, window, ventilator, shutters and partitions etc., with EPDM rubber / neoprene gasket etc., complete all as specified and directed. Note: cost of aluminium snap beading shall be paid in basic item.

M&L for particle board 12 mm thick prelaminated particle board with decorative lamination on one side and balancing lamination on other side, Grade I, Type II IS: 12823 marked fixing in aluminium / wooden partition with rubber / screw complete all as specified and directed.

M&L for providing and fixing pressed steel door frames conforming to IS: 4351, Profile B fixing with adjustable lugs with split end tail to each jamb manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50 x 25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface complete all as specified and directed.

M&L for 35 mm thick 2nd class hard wood factory made plain framed panelled, door shutter (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (part-I) kiln seasoned and chemically pressure treated complete all as specified and directed.

M&L for providing and fixing PVC Door frame of size 50 x 47 mm with a wall thickness of 5 mm ( + 0.2 mm), made out of single piece extruded PVC profile, with mitred cut joints and joint with 2 nos of PVC bracket of size 190 mm x 100 mm long arms of cross section size 35 x 15 mm & self driven self taping screws, the vertical door profiles to be reinforced with 40 x 20 mm M.S. rectangular tube of 0.8 mm, including providing EPDM rubber gasket weather seal throughout the frame, including jointing 5 mm PVC frame strip with PVC solvent cement on the back of the profile. The door frame to be fixed to the wall using 8 x 100 mm long anchor fasteners complete all as specified and directed.

M&L for 35 mm thick factory made solid panel PVC Door shutter, Decorative finish (wood grained finish) made out of single piece extruded solid PVC profiles, 5mm ( + 0.2 mm) thick, having styles & rails (except lock rail) of size 95 mm x 35mm x 5mm, out of which 75 mm shall be flat and 20mm shall be tapered (on both sides), having one side thickness of 15mm integrally extruded on the hinge side of the profile for better screw holding power, including reinforcing with MS tube of size 40mm x 20mm x 1mm, joints of styles & rails to be mitered cut & joint with the help of PVC solvent cement, self driven self tapping screws & M.S. rectangular pipes bracket of size 190mm x 100mm of cross section size 35mm x 17mm x1 mm at each corner. Single piece extruded 5mm thick solid PVC lock rail of size 115mm x 35mm, out of which 75mm to be flat and 20mm to be tapered at both ends, having 15mm solid core in middle of rail section integrally extruded, fixing the styles & rails with the help of solvent and self driven self tapping screws of 125mm x 11mm, including providing 5mm single piece solid PVC extruded sheet inserted in the door as panel complete all as specified and directed.

M&L for providing and fixing aluminium tower bolts, 150mm x 10mm dia ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade, with necessary screws, etc., complete all as specified and directed.

S & F Anodised aluminium butt hinges 100mm complete all as specified and directed.

M&L for providing and fixing 125mm aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade, with necessary screws etc complete all as specified and directed.

M&L for providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868), transparent or dyed to required colour or shade, with nuts and screws etc complete all as specfied and directed.

S&F in repair PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

M&L for providing and fixing to the inlet mouth of Multi way Nahi trap / drain U pvc (an Engineering Thermoplastic) grating round 100mm dia with a height of 8 mm and weighing not less than 75-100 gms complete all as specified and directed.

Dismantling 15 to 40 mm dia G.I. pipe including stacking of dismantled pipes (within 50 metres lead) complete all as specified and directed.

M&L for providing and fixing 15 mm nominal dia pipes chlorinated polyvinyl chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete all as specified and directed.

All as per item No 44 here in after but of size of 20 mm bore complete all as specified and directed.

M&L for providing and placing on terrace (at all floor levels) polyethylene water storage tank 1000 Litres, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank, including removal of old one complete all as specified and directed.

M&L for providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required (W.C. pan with ISI marked white solid plastic seat and lid) complete all as specified and directed.

M&L for providing and fixing white vitreous china clay half stall urinal flat back 580 x 380 x 350 mm or angle back 450 x 375 x 350 mm with waste fittings as per IS: 2556 complete all as specified and directed.

M&L for providing and fiixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require. White vitreous china wash basin size 550 x 440 mm with a pair of 15 mm C.P. brass pillar taps complete all as specified and directed.

Supply & fix ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 20 mm nominal bore complete all as specified and directed.

Supply & fix gun metal gate valve with C.I wheel of approved quality (screwed end) 20mm nominal bore complete all as specified and directed.

M&L for providing and fixing C.P. brass bib cock 15 mm nominal bore of approved quality conforming complete all as specified and directed.

Supply & fix toilet paper holder (C.P. brass) complete all as specified and directed.

M&L for providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 8931 15 nominal bore complete all as specified and directed.

Supply and fixing Brass chromium plated tubular towel rail, 20 mm dia, D type, 60 cm long between flanges, fixed in repair complete all as specified and directed.

Supply & fixing C.P. health faucets (1m tube & Hook) prayag category part No. BEA-87 or equivalent complete all as specified and directed.

S & F mirror of superior glass rectangular shape & size 1500 x 450 mm (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing complete all as specified and directed.

Dismantling POP false ceiling, cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead complete all as specified and directed.

M&L for providing and fixing tiled false ceiling of specified materials of size 595 x 595 mm in true horizontal level, suspended on interlocking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams / Sq.m, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required lenght and size 24 x 38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24 x 25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200 x 600 mm and secondary cross "T" of length 600 mm and size 24 x 25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200 x 600 mm panel to form grids of 600 x 600 mm and wall angle of size 24 x 24 x 0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/ making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc.

Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x 1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanized butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along with T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyster paint, all complete for all heights as per specifications, drawings. 8 mm thick fully perforated calcium silicate board made with Calcareous & Siliceous materials reinforced with cellulose fibre manufactured through autoclaving process to give stable crystalline structure with minimum compressive strength 225 Kg/Sq.cm bending strength 100 Kg/Sq.cm of size 595 x 595 mm, having perforation of dia.10 mm with minimum perforated area 18 % with non woven tissue on the back side, having an NRC (Noise Reduction Coefficient) of 0.85, with 50 mm thick rockwool of 48 Kg/Cum backing complete all as specified and directed.

Dismantling C.I. or asbestos/ PVC rain water pipe 150 mm dia pipe with fittings and clamps including stacking the material within 50 metres lead complete all as specified and directed.

Dismantling C.I. or asbestos/ PVC rain water pipe 110 mm dia pipe with fittings and clamps including stacking the material within 50 metres lead complete all as specified and directed.

M&L for providing & fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS: 13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10 mm gap for thermal expansion, single socketed pipes 110 mm diameter complete all as specified and directed.

M&L for providing & fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS: 13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10 mm gap for thermal expansion, single socketed pipes 150 mm diameter complete all as specified and directed.

M&L for providing & fixing on wall face unplasticised - PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS: 13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10 mm gap for thermal expansion, (i) 110 mm bend complete all as specified and directed.

All as per item No 64 here in before but bend for 150 mm dia pipe complete all as specified and directed.

All as per item No 64 here in before but shoe for 110 mm dia pipe complete all as specified and directed.

All as per item No 64 here in before but shoe for 150 mm dia pipe complete all as specified and directed.

Dismantling of EWC and their connected items complete all as specifed and directed.

Dismantling of white vitreous china clay half stall urinal flat any size in any position and their connected items complete all as specified and directed.

Dismantling of white vitreous wash basin any size in any position and their connected items complete all as specified and directed.

Dismantling of bib tap / pillar tap / stop valve / toilet paper holder / towel rail / health faucet / gun metal valve / brass valve etc and their connected items complete all as specified and directed.

Dismantling of looking mirror of any size and shape fixed in any position complete all as specified and directed.

M&L for 18-20 mm thick Granite stone slab colour black, Cherry/ Ruby red gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, steps, floor etc and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc complete all as specified and directed.

M&L for providing edge moulding to 18 mm thick Granite work, Vanities etc., including machine polishing to edge to give high gloss finish etc., complete all as specified and directed.

Supply & fixing venetian blinds, vertical type (blinds rolling upward & downwards), 100 mm slot width of approved fabric and powder coated aluminium top railset complete all as specified and directed. Note: The colour, design and shade shall be as approved by GE.

Dismantling strucutural steel work including doors, gates, stairways but excluding framed truss etc complete all as specified and directed.

Material and labour for stainless steel railing / posts of required size, fixed to sides of platform / path / stairways etc including suitable size steel bolt/ fasteners/ fitting etc complete all as specified and directed.

Taking down carefully U/S aluminium/ copper point wiring (light, fan, socket or power) complete with fittings such as switches, sockets, ceiling rose, light fittings etc , removing all material for reuse/ issued under schedule of credit and making good the distrubed surface as the existing one, complete all as specified and directed. Note: Cost of unserviceable materials will be charged from the contractor against schedule of credit.

M&L for point Wiring complete with 1.5 Sqmm single core PVC insulated but unsheathed multistranded copper conductor FRLSH cable 1100 volts grade drawn through and including non metallic rigid PVC heavy duty concealed conduit (minimum 25 mm dia external) but shall be increased as per actual site requirement in accordance with clause 19.125 of SSR part-I, ISI marked with wall thickness not less than 1.8 mm including conduit accessories like bends, tees, junction boxes etc fixed surface/ concealed/ recessed in wall or ceiling etc including 1.5 Sqmm PVC insulated but unsheathed multistranded copper conductor FRLSH cable as earth continuity wire including modular switch modular type metal flush box with cover plate and frame of required module mounting of modular switches, sockets, switch sockets, fan regulators with required modules complete all as specified and directed. (a) One light point controlled by one, one way switch 5 Amps

(b) One Ceiling fan point/wall fan/ exhaust fan point controlled by one, one way switch 5 Amps and regulator.

M&L for sub main Wiring single core, PVC insulated, unsheathed, multistranded copper conductor cable, 1100 volts, FRLSH Grade, ISI marked, drawn through and including suitable PVC non metallic rigid conduit medium grade with accessories fixed on walls / roofs / floors / ceiling etc and connecting terminals ends including one run of single core, PVC insulated, unsheathed, multistranded copper conductor, green in colour, 1100 volts, FRLSH grade as earth continuity conductor complete all as specified and directed. (a) 2 x 1.5 Sq.mm + 1 x 1.5 Sq.mm earth wire. Note: Two runs of 1.5 Sqmm copper cable, one run of earth wire of 1.5 Sqmm copper cable and 25 mm dia PVC conduit shall be measured and paid as on RM (for 27 point x 8 RM = 216 RM).

(b) 2 x 2.5 Sq.mm + 1 x 2.5 Sq.mm earth wire Note: Two runs of 2.5 Sqmm copper cable, one run of earth wire of 2.5 Sqmm copper cable and 25 mm dia PVC conduit shall be measured and paid as on RM (for 72 point x 8 RM = 576 RM).

Supplying and fixing GI box of 150 mm x 75 mm x 60 mm deep (nominal size) on surface or in recess with modular plate and cover in front including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. complete all as specified and directed.

Supplying and fixing GI box of 180 mm x 100 mm x 60 mm deep (nominal size) on surface or in recess with modular plate and cover in front including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. complete all as specified and directed.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box / wooden block including connections etc complete all as specified and directed.

Supply and fixing of modular fan regulator step type 120 W 230 Volts 2 module complete all as specified and directed.

Supply and fixing of sheet metal enclosure powder coated, Distribution board, Double door type, VTPN MCCB 125 Amps as incomer, 8 way, 415V, Double door type IP 43 protection, shrouded Neutral Bar & Pan assembly with flexible link Cement spill protector, Door earthing complete all as specified and directed.

Supply and fixing MCCB 4 pole 125 Amps 36 KA rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc complete all as specified and directed.

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc (but without MCB/RCCB/Isolator) complete all as specified and directed. (a) 6 way (4+18), Double door

(b) 8 way (4 + 24), Double door

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc (but without MCB/RCCB/Isolator) complete all as specified and directed. (a) 6 way, Double door

(b) 8 way, Double door

(c) 12 way, Double door

Supply & fixing of MCB, SP, 240V, 06 to 32 Amps 10 KA rupturing capacity complete all as specified and directed.

Supply & fixing of MCB, SPN, 240V, 06 to 32 Amps 10 KA rupturing capacity complete all as specified and directed.

Suppply & fixing of 30 A, 415 V, TPN industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 32 A "C" curve, TP, MCB, in sheet enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc complete all as specified and directed.

Supply & fixing MCB TP, 415 V, 32 Apms, 10 KA, "C" curve complete all as specified and directed.

Supply & fixing 20 A, 240 V, SPN industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete connections, testing and commissiong etc complete all as specified directed.

M&L for sub main wiring with four single core PVC insulated unsheathed, 1100 volts grade, copper cable 4x16 Sqmm stranded conductor and drawing through and including rigid PVC non metallic surface conduit medium grade of suitable size with conduit accessories such junction boxes, bends, tees etc., including continous earth wire PVC insulated unsheathed 1100 volts grade, 2 run of cable 16 Sqmm copper conductor and connected to common earth dolly including taking down old submain wiring complete all as specified and directed. Note: One run of PVC conduit, 6 runs of cable shall be measured and paid as one unit.

M&L for sub main wiring with four single core PVC insulated, unsheathed, 1100 volts grade, copper cable 4x10 Sqmm stranded conductor and drawing through and including rigid PVC non metallic surface conduit medium grade of suitable size with conduit accessories such junction boxes, bends, tees etc., including continous earth wire PVC insulated unsheathed 1100 volts grade, 2 runs of cable 10Sqmm copper conductor and connected to common earth dolly including taking down old submain wiring complete all as specified and directed. Note: One run of PVC conduit, 6 runs of cable shall be measured and paid as one unit.

M&L for sub main wiring with four single core PVC insulated, unsheathed, 1100 volts grade, copper cable 2x6 Sqmm stranded conductor and drawing through and including rigid PVC non metallic surface conduit medium grade of suitable size with conduit accessories such junction boxes, bends, tees etc., including continous earth wire PVC insulated unsheathed 1100 volts grade, 1 run of cable 6 Sqmm copper conductor and connected to common earth dolly including taking down old submain wiring complete all as specified and directed. Note: One run of PVC conduit, 3 runs of cable shall be measured and paid as one unit.

M&L for sub main wiring with four single core PVC insulated, unsheathed, 1100 volts grade, copper cable 2x4 Sqmm stranded conductor and drawing through and including rigid PVC non metallic surface conduit medium grade of suitable size with conduit accessories such junction boxes, bends, tees etc., including continous earth wire PVC insulated unsheathed 1100 volts grade, 1 run of cable 4 Sqmm copper conductor and connected to common earth dolly including taking down old submain wiring complete all as specified and directed. Note: One run of PVC conduit, 3 runs of cable shall be measured and paid as one unit.

Supply & fixing LED batten luminaire not less than 20 watt fitting 4' long with white powder coated housing & frame in CRCA sheet, High efficiency LED grade difuser, electronic driver duly wired upto terminal block CRI>80, LED colour temperature - 5700k, IP 20, 50000 burning hours as per L70 criteria, ambient temperature - 0 to 50 Deg C, Driver efficiency>85 %, THD<10%, PF>0.95, surge protection in CM - 3KV, multistage isolated constant current, constant voltage operated driver with range 150-270V AC and safety extra low voltage safe level<60V DC as per IEC standard including batten / suspension system complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed.

Supply & fixing recess mounted full panel LED luminaire 36 watt fitting 2'x2' with white powder coated housing & frame in CRCA sheet, high efficiency LED grade diffuser, electronic driver duly wired upto terminal block, CRI>80, LED colour temperature - 5700k, IP 20, 50000 burning hours as per L70 criteria, ambient temperature - 0 to 50 Deg C, Driver efficiency >85%, THD<10%, PF>0.95, surge protection in CM-3KV, multistage isolated constant current, constant voltage operated driver with range 150-270V AC and safety extra low voltage safe level <60V DC as per IEC standard complete all as specified and directed.

Supply and fixing LED street light fitting 36 watt 230 V AC outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65 / 66 protection complete and testing commissioning with 25 mm GI pipe with accessories to fit the light fitting complete all as specified and directed. Note: All necessary fixing / connecting arrangements of nuts, bolts, MS rod to be provided by the contractor without any extra payment from department.

Taking down old existing ceiling fan 1200/1400 mm sweep single phase, servicing and painting of ceiling fans and refixing and connecting with necessary cable from ceiling rose or connector to fan and making good to damaged surface of wall / ceiling to match existing finish complete all as specified and directed.

Taking down old existing exhaust fan 300/400 mm sweep single phase, servicing and painting of existing fans and refixing and connecting with necessary cable from ceiling rose or connector to fan and making good to damaged surface of wall / ceiling to match existing finish complete all as specified and directed.

M&L for power console made out of aluminium insulation material poly carbonate sheet of colour as approved in standard length comprising of 5 Nos 5/15 Amps 5 pin electric socket controlled by two switch (modular type) with one control MCB 20 Amps SP and indication lamp fitted, internal wiring including fixing of console on pedestal made out of MS frames, etc of suitable size complete all as specified and directed.

M&L for earthing complete with GI earth plate electrode 600 x 600 x 6 mm thick GI earthing lead buried directly in ground vertically to a depth not less than 2.25 m deep below GL with the top edge of the plate at a depth not less than 1.5 m from below normal GL connected to and including GI wire 6 SWG as earthing lead by means of nuts, bolts, washers, check nuts of galvanised iron and connected to earthing test point all as shown in electric plate No. 3 of SSR part-I of 2010 and as specified or indicated and testing on completion including excavation / earthwork in any type of strat PCC (1:3:6) type C1 earthing chamber, precast slab 50 mm thick in cement concrete (1:2:4) type B1 (reinforced with welded steel wire fabric (XPM) weight not less than 4 Kgs of 40 mm bore medium grade and lugs with and lugs, including GI wire with GI protection pipe of 40 mm medium grade 7.5 m long etc including testing and submission of test reports within permissible limit complete all as specified and directed. Note: Rate quoted shall deemed to include cost of excavation in any type of strata, RFR and removal upto 50 metre, PCC pit, funnel and RCC cover plate, GI pipe etc.

M&L for providing and fixing 6 SWG dia GI wire on surface or in recess for loop earthing along with existing surface / recessed conduit / submain wiring / cable as required.

Supply and fix MCB TPN 415 volts 50 Hz 10 KA 'C' series 63 Amps complete all as specified and directed

Siddivinayaka Constructions (BID ID -3169725)

ABHISHEK CONSTRUCTIONS (BID ID -3164430)

Lucky Enterprises (BID ID -3170433)

D NAGI REDDY (BID ID -3160967)

B5BUILDING SOLUTIONS (BID ID -3164457)