IMPROVEMENT TO CERTAIN OMQS AT NORTH CAMP AND PROVN OF IRON GRILLS AT VARIOUS LOCATION AT AF STN BAMRAULI

Amount

M&L for providing cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in foundation complete all as specified and as directed

M&L for sub class ‘B’ old size bricks, straight or curved on plan exceeding 6 m mean radius, built in cement mortar 1:4 complete all as specified and directed.

M&L for providing cement concrete 1:2:4 type B1 using 20mm graded aggregate as in copping and fixing of angle iron post etc. including weathering, slightly rounded or chamfered angles and necessary formwork complete all as specified and as directed

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails,braces, etc., complete, drilled for fixing of steel sheeting or other covering etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing conforming to Fe 410-W (Gde-E- 250) quality- AFecomplete all as specified and directed.

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar 1:6 on brick work or concrete surfaces for finishing the surface fair and even. without using extra cement complete all as specified and directed.

M&L for two coats of cement base paint over a coat of cement primer including preparation of new plastered surfaces of walls complete all as specified and directed.

M&L for preparation of new steel or iron surface of any description, exceeding 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete and all as specified and directed.

Dismantling, floor any type, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete.

M&L for glazed ceramic tiles in vertical surfaces of size 450x350x7mm thick set and jointed in neat cement slurry and pointed with white or coloured cement to match over and including rendering 10 mm thick in cement mortor (1:4) on vertical surface as in backing coat all as specified and directed.

S&F 300x300 mmx7-8 mm thick ceramic non skid tiles in floor, set & jointed in neat cement slurry and pointed in white or colured cement to match over 20mm thick screed bed in cement morta 1:6 complete all as specified and directed.

M&L for vitrified ceramic tiles 10mm thick dark shade (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match laid in floors set and jointed as per manufacturer's instructions Over & including screed bed or bedding layer 15mm thick in CM (1:6) complete.

All as per item No 4 above but skirting including 10 mm thick rendering in cement mortar 1:4, complete all as specified and directed.

M&L for non skid Heavy duty Endura tile 400x400x12mm thick coloured joint free in floors etc set and jointed in neat cement slurry and pointed in colored cement to match over and including 15mm thick screed in CM 1:4 complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in leveling course to floor complete all as specified and directed.

Taking down chowkhat or frame with shutters (without taking off shutters from the frame) n. exc. 1.5 Sqm each complete all as specified and directed.

All as per item No 16 above but exc. 1.5 Sqm and not exc. 4 Sqm complete all as spd & directed.

M&L for Aluminium window/ventilator (Powder coated ) double leaf /three leaf with anodized aluminium frame sliding/openable including wheel powder coated of section 62.5x37x2.5 mm thick shutter with bottom & middle rail of section 112.5x37x2.5mm and style & top rail of section 83x37x2.5mm thick with centrally locking arrangement with lock rail of rebate including joints cleat fixing of builders hardware fittings necessary and gazing with 5mm thick ordinary plain glass including wire mesh shutter necessary fittings fixuters & aluminium snap beads complete.

S&F mild steel framed work such as door frame, grills, grating hold fast etc. with ends of bar shoulder and/or riveted, or forged into spikes, framed guard bar including necessary welding, drilling hole complete.

S&F flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides of thickness 30 mm complete all as specified and as directed.

S&F 35mm thick second class hardwood glazed and Skelton factory made door shutters, open rebated and prepared to receive glass/gauze etc divided into squares with plain, chamfered or rounded mitered and rebated sash bars, edges of framing plain, chamfered, fitting with cut and rebated beads for securing glass/ gauge complete all as specified in SSR Pt I-2009 section 8 clause 8.24 (a) and as directed.

S&F Factory made internal PVC Door frame of size 100X45mm with a wall thickness of 5mm made out of extruded 5mm prelam PVC foam sheet of density 600kg/cbm manufactured by an ISO-9001-2008 certified compnay mitre cut at two corner and jointed with 4 Nos of 150mm long brackets of 15x15mm MS Square tube or fusion heat welding proces the two vertical door frames to be reinforced with 40x20mm MS tube of 19 gauge through out the framr. the door frame shall be fixed to the wall using 65/100mm long MS screws through the frame by using PVC Fasteners a minimum of 4 nos of screws to be provided foe each vertical member & minimum 2nos for horizontal member etc complete all as per manufactures Specified.

S&F 30mm thick factory made solid panel PVC door shutter consisting of frame made out of M s tube of 19 gauge thickness and size 40x20mm for stiles as well as top lock & bottom rails MS frame shall have a cost of matel primer of approved make & manufacture MS frame shall be covered with heat moulded prelam'C' channel made from5mm (#.25) thick PVC sheet of density 600kg/cbm manufacture by an ISO-9001-2008 certified compnay of size 30mm thick & 110mm width forming stiles in which 100mm should be flat & 5mm should be taper and 5mm (#0.25) thick 135mm wide PVC sheet for top rail and bottom rail in which 125mm should be flat & 5mm taper on either side an additional 5mm thick PVC solvent cement adhesive peneling of 10mm prelam PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with 30mm wide x 5mm (#0.25) 30mm thick Pvc sheet beading either side & additional 30mm wide PVC beading as gap insert below top & bottom rail joined together using solvent cement adhesive 15mm thick 5mm0.25)x 3) 20mm wide croner PVC sheet as gap insert for top and bottom rail door to be fitted with frame with 3 nos ms powder coated butt hinges of size 100mm 25mm &n 50mm longer steel screws drilled suitable to pass through both the wall of the MS tube other hardware's of door should be fixed with 25mm 8mm size steel screws etc. complete as per manufactures Sfd.& drawing including iron mongery all fiting complete all as sfd and directed.

M&L for 105X60 mm Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed

S&F 125X60 mm Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed

S&F 100mm Aluminum hinges, complete type B-21

S&F 200 mm long aluminium anodised barrel tower bolts ISI marked of extruded section and fixed

S&F 150 mm size aluminium handles 'D' Type ISI brand cast type, anodised complete.

S&F 300 mm aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sec or cast aluminium and fixed complete.

M&L for applying two coats of synthetic enamel paint on new or old wooden surfaces of any description over 10 cm width or girth over a coat of pink primer including preparation of surfaces complete.

S&F MS flat iron as in hold fast etc and similar work incuding making shape, drilling holes etc, confriming to FE 290 Ged E-165

M&L for PCC (1:3:6) type C1 (using 20mm graded stone aggregate) as in bed plate for fixing holdfast etc all as specified and directed.

S&F Aluminium alloy wire cloth, 0.45 mm nominal dia of wire and average width of aperture 1.40mm and fixed with beading to wooden frames all as specified and as directed.

S&F drapery rod 19mm inner dia (wall thickness not less than 1.60mm) stainless steel fancy type bracket fixed with rawl plug or screws on wall/beam and shall be provided with fancy finial at ends as approved by Garrison Engineer complete all as specified and directed. Note :- (i) Drapery rod Cat part no- SW-06 of vista or equivalent model of make as specified in Appendix "B" to particular specification.

S&F in curtain brackets stainless steel with matching with the curtain rod complete all as specified and directed.Note :- (i) Drapery rod Cat part no- SW-06 of vista or equivalent model of make as specified in Appendix "B" to particular specification.

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensil strength of 550 Mpa as in roof covering to wall fixed with self tapping screws as specified.

S&F Pre painted galvalume aluminium zinc coating GI base plain steel sheet 0.50mm thick (TCT) of an colour having minimum tensile strength of 550 Mpa as ridge in roof fixed with self tapping screws as specified in particular specifications. Note :- (i) Outer colour of sheet shall be as approved by GE based on availability from manufacturer. (ii) Work shall be executed by the manufacturer's authorised Vendor only.

M&L for Cement concrete in walls or retaining walls ,Type B2(1:2:4) 40mm graded stone aggregate any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases)

S&F in repair vitreous china wall hung wash hand basin with pedestal snow white miniumum size 630mmx450mm including chromium plated brass coupling, bottle trap, chromium plated brass centre hole basin mixer, 450 mm PVC braided connection (two numbers), angular stop cock ( valve) (two numbers) complete all as specified in particular specifications.

S&F in repair One piece Vitreous china wash down water closet (Pedestal Pattern) size 645mmx35mmx730mm 'white' with soft close seat cover & twin flush fittings, toilet paper holder, health faucet, PVC connection, angular stop cock (valve) (2 Nos) with flange etc all as specified in Particular specifications.

S&F 15 mm bore bib taps, with wall flange long body, cast copper alloy, chromium plated, fancy type with crutch or butterfly handle, screwed down screwed for iron pipe or for brass furrel complete in repairs

S&F in repair, stainless steel sink with drainage board made out of 1mm thick of size 1040mmx510mm, bowl size 460x410x190mm including CP brass waste coupling, PVC Waste pipe,brackets etc complete all as specified and directed.

S&F in repair stop valve brass chromium plated fancy type 15mm bore with wall flange of authentic single lever for iron pipe or for unions complete all as specified and directed.

S&F in repair toilet cabinet PVC with mirror and shelves (600x450) etc complete all as specified and directed

S&F in repair Chromium plated stainless steel (Grade S-304) (heavy) grating minimum 3 mm thick of size 125mm dia for trap

S&F in repair stainless steel plate rack of size 900x600x200mm of best quality made out of 1mm thick sheet etc complete all as specifed and directed.

S&F in repair Chromium plated stainless steel towel rail with lower hanger with hooks fixed to wall with chromium plated brass screws 600mm long between flanges complete.

S&F in repair 600mmx450mm and 6mm thick bevelled edge looking mirror mounted on 6mm thick backing comercial plywood fixed with CP plug with chromium plated brass screws and cup washer fioxed on wall complete.

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 120mm (minimum) wide with chromium plated brass bracket guard and railing 600mm long complete.

S&F Chromium plated brass soap dish (oval shape) to walls (size not less than 125mm long).

S&F Brass chromium plated mist wall mixer (hot and cold) non telephonic fixed to wall for bathroom complete all as specified and directed.

Demolition & breaking AC drain pipes (salt glzed ware, AC,PVC) set in cement mortar,dia of pipe 100 mm

S&F of 75 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed

S&F of 110 mm dia(SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed

S&F 75 mm bore PVC (SWR) bends any radius complete all as specified and directed

S&F 110 mm bore PVC (SWR) bends any radius complete all as specified and directed

M&L for Cast iron floor trap of 100mm dia, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

Taking up or down 15 mm dia steel tubing and connections including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down 20 mm dia steel tubing and connections including cleaning for refixing or removal to store complete all as specified and directed.

S&F 15 mm bore galvanised steel water tubing 'medium grade' with all fittings and fixed to walls, ceiling or laid in floors etc. complete all as specified and directed.

S&F 20 mm bore galvanised steel water tubing 'medium grade' with all fittings and fixed to walls, ceiling or laid in floors etc. complete all as specified and directed.

M&L for cutting chases brick walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends and making good cutting exceeding 20cm girth for concealed water tubing or concealed conduit wiring, etc.complete all as specified and directed.

S&F in repairs 500 litres capacity rotational moulded polyethylene water storage tanks triple layer,white colour (Cylindrical vertical with closed top) hoisted and fixed in position including dismantling all as specified in SSR Part I complete all as specified and directed

S&F Ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (minimum weight 210 gms) of bore of pipe 20mm complete all as specified and as directed.

S&F in repairs 18mm thick celuka PVC sheet minimum 600 Kgbm density grade 1 quality of both side plain white colour rigidlam glossy finish fixed with screws, solvent cement/adhesive as per manufacturer instructions to make kitchen cabinet sides top and bottom and shelves inside the cabinet complete as per specifications and as directed by the Engineer-in-Charge. Note:- (i) Cupboard accessories i.e. fittings, handles, hinges, will be measured and paid for seperately as supply only under respective of this schedule. (ii) Quoted rates deem to be include fixing of cabinet on wall with appropriate rawl plug/ dash through fastener (hammer type). (iii) Fabrication and installation of cabinet to be carried out by authorised vendor of manufacturer only.

S&F in repairs 18mm thick celuka PVC sheet minimum 600 Kgbm density grade 1 quality one side pre-laminated and other side plain white colour to make kitchen cabinet/drawer shutters fixed with screws, solvent cement/adhesive as per manufacturer instructions complete as per specifications and as directed by the Engineer-in-Charge. Note:- (i) Handles, hinges, will be measured and paid for seperately as supply only under respective of this schedule. (ii) Quoted rates deem to be include fixing of cabinet on wall with appropriate rawl plug/ dash through fastener (hammer type). (iii) Colour and design of prelaminated portionshall be as approved by GE. (iv) Fabrication and installation of cabinet to be carried out by authorised vendor of manufacturer only.

S&F in repairs 12mm thick celuka PVC sheet minimum 600 Kgbm density grade 1 quality of one side plain white colour rigidlam glossy finish fixed with screws, solvent cement/adhesive as per manufacturer instructions to make kitchen cabinet back complete as per specifications and as directed by the Engineer-in-Charge. Note:- (i) Cupboard accessories i.e. fittings, handles, hinges, will be measured and paid for seperately as supply only under respective of this schedule. (ii) Quoted rates deem to be include fixing of cabinet on wall with appropriate rawl plug/ dash through fastener (hammer type). (iii) Fabrication and installation of cabinet to be carried out by authorised vendor of manufacturer only.

Supply only autoclosing hydrolic (soft closing) chrome finish stainless steel hinge openable at 110 degree complete.

Supply only 100mm long stainless steel (grade S-304) handle fancy type polished bright chrome finish complete.

Supply only 200mm long stainless steel (grade S-304) handle fancy type polished bright chrome finish complete.

Demolition of brick work or stone masonary built in cement mortar including all quoins, arches, pillars etc complete.

M&L for brick work with sub class 'B' modular brick straight or curved on plan exc. 6 m mean radius built in cement mortar 1:6 complete.

Taking down cement plaster on brick or stone walls, etc, incl raking out joints, hacking for key, scrubbing down with water, etc & prepare to receive new plaster complete all as specified and directed

M&L for rendering 5mm thick in CM 1:3 finished even and smooth with out using extra cement in ceiling complete all as specified and directed

M&L for 15mm thick rendering in CM 1:4 on fair faces of brick work, surfaces finished even and fair without using extra cement complete all as specified and directed

Preparation of new plastered surface of wall and applying two coats of ACE exterior paint over 1mm thick wall care putty complete all as specified and directed.

M&L for two coat of oil bound distemper on newly plastered surface on wall over 3mm thick wall care putty all as specified and directed.

Preparation of new plastered surface of ceiling and applying two coat of oil bound distemper over 1.5mm thick putty complete all as specified and directed.

M&L for complete removing of existing treatment on wall surface and applying two coat of OBD over 3 mm thick birla white care Putty on wall to obtain smooth finish etc complete all as specified and directed.

M&L for complete removing of existing treatment on ceiling surface and applying two coat of OBD over 1.50mm thick birla white care Putty on wall to obtain smooth finish etc complete all as specified and directed.

M&L for preparation of old decorated surface of wall, roof or sheet any type and applying two coat of ACE exterior emulsion paint (Asian Paint) complete all as specified and directed

Easing of door shutters for easy closing / opening, end tightening of butt hinges in position, adjustment of butt hinges in position, adjustment of existing iron mongry exc 1 Sqm and n.exc 2 Sqm each complete all as specified and directed.

Easing of door shutters for easy closing / opening, end tightening of butt hinges in position, adjustment of butt hinges in position, adjustment of existing iron mongry exc 2 Sqm each complete all as specified and directed.

S&F Floor door stopper of aluminium alloy body and tounge anodised,with hard drawn steel spring, with overall length of cover plate 140mm

S&F rubber bead for wooden door complete all as specified and directed.

Supply only stainless steel chrome plated (Grade S-304) basket (plain) of minimum size 50cmx37cmx10cm made of 4mm minimum dia S.S. wire approved quality with and including stainless steel chrome finish (Grade S-304) ball bearing telescope channel (full extension mechanism) (two numbers) for fixed to board

Supply only stainless steel chrome plated (Grade S-304) thali basket (11-13 divisions) of minimum size 50cmx37cmx20cm made of 4mm minimum dia S.S. wire approved quality with and including stainless steel chrome finish (Grade S-304) ball bearing telescope channel (full extension mechanism) (two numbers) for fixed to board

Supply only stainless steel chrome plated (Grade S-304) plate basket (11-13 divisions) of minimum size 50cmx37cmx16cm made of 4mm minimum dia S.S. wire approved quality with and including stainless steel chrome finish (Grade S-304) ball bearing telescope channel (full extension mechanism) (two numbers) for fixed to board

Supply only stainless steel chrome plated (Grade S-304) Partition basket of minimum size 50cmx37cmx16cm made of 4mm minimum dia S.S. wire approved quality with and including stainless steel chrome finish (Grade S-304) ball bearing telescope channel (full extension mechanism) (two numbers) for fixed to board

Supply only stainless steel chrome plated (Grade S-304) cutlery basket of minimum size 50cmx37cmx10cm made of 4mm minimum dia S.S. wire approved quality with and including stainless steel chrome finish (Grade S-304) ball bearing telescope channel (full extension mechanism) (two numbers) for fixed to board

Supply only stainless steel chrome plated (Grade S-304) bottle pullout of minimum size 50cmx40cmx16cm made of 4mm minimum dia S.S. wire approved quality with and including stainless steel chrome finish (Grade S-304) ball bearing telescope channel (full extension mechanism) (two numbers) for fixed to board

Supply only stainless steel chrome plated (Grade S-304) grid basket (plain) of minimum size 50cmx52cmx20cm made of 4mm minimum dia S.S. wire approved quality with and including stainless steel chrome finish (Grade S-304) ball bearing telescope channel (full extension mechanism) (two numbers) for fixed to board

Demolition of reinforced concrete of any description and in any position not otherwise specifically provided for

M&L for precast cement concrete 1:2:4 type C1 using 20 mm graded stone aggreagate as in landing , cover slab(for manholes, etc) chulla hoods, chajjas, water through, mangers shelves and similar articles including form work complete all as specifeid and directed.

Mild steel TMT bars 6 mm dia and over, upto and including 10mm dia,cut to length, bent to shape required, including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and as directed.

M&L for granite (of any type) 20mm thick machine cut, bedded and jointed with white cement with admixture of pigmewnt to match the shade of granite stone incld griding and polishing including 15 mm thick screed bed in CM(1:6) complete all as specified and directed.

Taking down carefully aluminium batten point, wiring for light/fan/socket/bell or power point including. All fittings i.e. switch, sockets, ceiling rose, regulators, batten holders, etc. Complete and making good disturbed surfaces of wall/floor to match with the surroundings of wall/ceiling/floor etc including taking down old light fittings. Note :- (i) Contractors quoted rate of this item deemed inclusive of unscrewing of the serviceable fittings and fixture as directed and deposit in MES store yard. (ii) Quoted rate also deem to be included cost of cutting chases for taking out concealed conduit and nitch for terminal box. (iii) Decision of GE shall be final and binding in respect of serviceability of fittings/fixture.

M&L for Point wiring complete with 1.5 sqmm single core PVC insulated FRLS cable 1100 volts grade with multi stranded copper conductor drawn through new PVC concealed conduit mediem grade, ISI marked and including provision of 1.5 sqmm PVC insulated copper cable FRLS as earth continuty, fabricated branded modular metal flush box duly make embossed, concealed in walls with suitable modular inner and outer plate for housing switches , socket outlet and fan regulators etc, complete all as specified and as directed for the followings:-

(a) One light/fan/bellpoint controlled by one switch single pole one way

(b) All as per item No 100 here-in-before but one 3 pin 6 amp switch socket out let independent .

(c) All as per item No 100 here inbefore but one 3 pin 6 amps socket outlet on the same board with other switch complete .

All as per item No 100 here-in-before but using 02 Nos. 4.0 sqmm size for main cable and 01 No.2.5 sq mm size as earth conductor for one 16 Amp switch socket outlet on independent board.

S&F switch modular flush 10A single pole one way ISI marked

S&F modular sockets 10 Amp 2 in 1 2/3 pin combined all as specified and directed.

S&F switch modular flush type 15/16 Amp single pole one way 240 volt one module ISI marked

S&F modular sockets 16 Amp 2 in 1 3/5 pin combined all as specified and directed.

S&F ceiling rose surface bakelite 60x25mm three terminal

S&F Modular Fan step regulator, 120W - 2 module complete all as specified and directed.

S&F LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

S&F LED batten extruded surface mounting fitting 2 feet long aluminium housing 10 watt input voltage 220 volt inbuilt LED and driver complete all as specified and as directed.

S&F flood light for building illumination 30 watt 240 volt 50 Htz 6500K 120 lumen/watt IP-65 protection complete all as specified and directed.

S&F Ventilating Fan 250 mm sweep, 1250 RPM, non metallic resin body, single phase 240 volts AC 50 Hz and connecting up complete including louvers and provision of making holes and copper cable 3 core of size 0.5 sqmm for connection from ceiling rose to fan complete all as specified and as directed.

S&F exhaust fan 300 mm sweep metalic body copper bound including fixing and louver shutter 240 volt 50 Htz. complete all as specified and directed.

S&F wall mounted fan 400mm, 230 volts, 50 Hz 1420 RPM with 90 degree oscillation and having speed control by two pull cord system all as specified and directed.

M&L for taking down carefully existing ceiling fan/exhaust fan from site before B/R repair work, keeping in safe custody in store for greasing / oiling of ball bearings / bushes and making it for smooth and noise free operation and painting with Hi-Gloss synthetic enamel paint of approved shade by spray painting after filling cavities' and re-fixing after providing new fan clamp, nuts/bolts, washers, down rod as required and provision of 3 core copper flexible cable of size 1.0 Sqmm from ceiling rose to fan connector complete with writing of MES No. on the fan surface all as specified and directed.

S&F ceiling fan 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush less direct current (BLDC) motor, class of insulation : B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, power factor not less than 0.9, service Value ( CMM/W) minimum 6.00, Air delivery minimum 210 CMM 350 RPM ( tolerance as per IS : 374 - 2019), THD less than 10 % ,electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise = 75 degree C (max), insulation resistance more than 2 mega ohm, suitable for 230 V , 50 Hz, single phase AC supply, earthing etc including necessary connection with ceiling rose with 3 core 1.0 Sqmm PVC insulated round flexible cable and including writing MES No all as specified and as directed.

S&F sheet metal enclosure with socket and plug top and MCB single pole and neutral enclosure with two Pin and earth plug and socket complete with one single pole MCB, 240 V, 25 Amp.

S&F MCB DB SPN 8 way, double door, IP-43, IK-09, Isolated Neutral Bar and fixed flush to wall and suitable for universal mounting complete all as specified and directed.

S&F MCB DB SPN 12 way, double door, IP-43, IK-09, Isolated Neutral Bar and fixed flush to wall and suitable for universal mounting complete all as specified and directed.

S&F MCB, single pole and neutral, 230 volts, 32 Amp rating, 'C' series fixed in DBs catered here-in-before.

S&F MCB, single pole and neutral, 230 volts, 40 to 63 Amp rating, 'C' series fixed in DBs catered here-in-before.

S&F MCB SP 6-32 Amps 240 volts 10 KA 50 HZ 'C' curve complete all as specified and directed by Engineer in charge

M&L for taking down carefully existing geyser of any type and cap from site before B/R repair work, keeping in safe custody in store for servicing and painting with Hi-Gloss synthetic enamel paint of approved shade by spray painting after filling cavities, writing of MES No. and re-fixing with new hot and cold water connection as required incl provision of 3 core copper flexible cable of size 2.5 Sqmm complete with 15 Amps 3-pin plug top all as specified and directed.

S&F water heater storage type (Geyser) vertical type with suitable size of fastner and incl provision and connecting up of SS braided pipe suitable size with adopter for inlet and outlet water connection having adjustable knob for temperature control and inner tank should be glass line coated complete all as specified of capacity 25 ltrs having element 1.5/2 KW BEE star rating incl taking down old and deposted to MES store yard

Sub main wiring with 2 run of single core PVC insulated and PVC Unsheathed, multistranded copper condutor of nominal area 6 sqmm FRLS, 1100 Volts grade cable drawn into and including rigid non metalic PVC Conduit of including all fittings and one run of PVC insulated and PVC unsheathed, multistranded copper conductor of nominal area 4 sqmm FRLS 1100 volts grade cable continuous earth wire of green colour code complete. Note:- (a) Two runs of 6 sqmm cable and one run of 4 Sqmm cable as earth lead with conduit shall be measured as one unit length for payment. (b) Quoted rate shall deem to be included cost of cutting chasses in wall for concealling conduit and making good to match with existing finish.

Sub main wiring with 2 run of single core PVC insulated and PVC Unsheathed, multistranded copper condutor of nominal area 4 sqmm FRLS, 1100 Volts grade cable drawn into and including rigid non metalic PVC Conduit of including all fittings and one run of PVC insulated and PVC unsheathed, multistranded copper conductor of nominal area 4 sqmm FRLS 1100 volts grade cable continuous earth wire of green colour code complete. Note:- (a) Two runs of 4 sqmm cable and one run of 4 Sqmm cable as earth lead with conduit shall be measured as one unit length for payment. (b) Quoted rate shall deem to be included cost of cutting chasses in wall for concealling conduit and making good to match with existing finish.

S&F in replacement of decorative type wall mounted luminaire (Comet) with unbreakable poly carbonate materials incl 1x12 watt LED bulb complete all as specified and directed by Engineer in charge .

S&F in repair factory made epoxy powder coated Load line Distribution Board TPN-4 ways with metal door (IP-43 protection) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including insulated 200 Amp copper bus bar, Isolated neutral bar, standard DIN rail, Earth bar and cable ties for cable management, top and bottom removeable gland plates with knockouts and suitable for one TPN- MCCB any capacity as incomer and 6 to 63 Amp SP MCBs outgoing complete all as specified and conforming to IS : 8623.

S&F in repair MCCB 100 Amps, FP 415 volts 16 KA 50 HZ with thermal magnetic setting complete all as specified and directed by Engineer in charge.

Note :- Credit shown in credit schedule of tender document shall be considered by the tenderer while quoting the rates of various items. The same shall be recovered from various payment to contractor before handing over old material.

M.R. ENTERPRISES (BID ID -3067529)

Shivam Traders (BID ID -3067817)

M/S V K MEHROTRA (BID ID -3067064)

ASHWANI BUILDERS & SUPPLIERS (BID ID -3067616)

R K CONSTRUCTION COMPANY (BID ID -3067584)

M/S SATISH KUMAR (BID ID -3067412)

M/S SURISONS (BID ID -3067483)