Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹3.4 LAccepted-AOC 141 1 ARYAPALLY BARONILPUR NORTH P O SRIPALLY DIST PURBA BARDHAMAN PIN 713103 | PURBA BARDHAMAN | PURBA BARDHAMAN | WEST BENGAL | 713103 | L1 | Accepted-AOC AS L1 BIDDER | |
| 2 | L2₹3.4 L+₹191.17 (0.06%)Rejected-AOC BARANIJPUR SAKTIPARA BURDWAN | L2 | Rejected-AOC AS L2 BIDDER | |
| 3 | L3₹3.4 L+₹472.84 (0.14%)Rejected-AOC 266 1 S B GORAI ROAD BESIDE VIDYASAGAR MAIDAN ASANSOL 713301 | ASANSOL | BURDWAN | WEST BENGAL | 713301 | L3 | Rejected-AOC AS L3 BIDDER |
Tender Value
Refer Docs
EMD Value
₹6,980
Closing Date
26 Sept 2022, 6:30 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
EXECUTIVE ENGINEER,CMD,PHED
EE,CMD,PHED,5 TH FLOOR,PURTA BHAWAN
Replacement-of-damaged-pumping-machinery-and-other-electro-mechanical-works-in-Pump-House-no-1-at-Purbasthali-Water-Supply-Scheme-under-CMD-PHE-Dte-Dist-Purba-Bardhaman
2022_PHED_399738_4
WBPHED/EE/CMD/eNIT-16/2022-23
Open Tender
Electrical Work/ Equipment
Item Rate
21 days
PURBASTHALI
Replacement-of-damaged-pumping-machinery-and-other-electro-mechanical-works-in-Pump-House-no-1-at-Purbasthali-Water-Supply-Scheme-under-CMD-PHE-Dte-Dist-Purba-Bardhaman
5 documents required · 5 mandatory
₹6,980
EXECUTIVE ENGINEER CENTRAL MECHANICAL DIVISION PHE
9 Nov 2022
12 Sept 2022
29 Sept 2022
12 Sept 2022
26 Sept 2022
13 Sept 2022
13 Sept 2022
Amount
Hiring charges of derrick set for withdrawing of pumping machinery as per direction of EIC.
Withdrawing of the damaged 7.5 HP Submersible Pump Motor set alongwith 2" dia 60ft. M.S. Column Pipe after disconnection of all electrical and pipe line connection etc. complete as per direction of EIC.
Supply & delivery of the following Pumping machinery, Electrical accessories etc. at site. a) Submersible Pumping Machinery, directly coupled with suitable size water proof motor having following specifications. P U M P DISCHARGE ( 16 M3/H) H E A D (75 mtr.) S H A F T. Stainless Steel. OUTLET SIZE. 65mm. PUMP EFFICIENCY IN PERCENTAGE: Minimum 65. M O T O R (7.5HP) (DOL Connection) Submersible type, 3ph.50Hz, A.C.- 400Volt +10%, wet type winding, RPM-2900. SIZE OF TUBEWELL : (150mm. x 150mm.dia). and length of Housing pipe 48.00mtr. Pump motor set must be BEE standard energy star rating (3-5) as per IS – 8034:2002 Make-KSB/PLUGA/B.G./TEXMO/ Approved Make). N.B.;- (I) H/Q Characteristic Curve of pump set should be submitted before delivery. (II) Test certificate of pump & motor should be submitted during delivery & G.C.
b) 4.0 sq.mm.3core, water proof flat cable, suitable for above pump set. (Make-FINOLEX /GLOSTER /MESCAB /CURRENCY/Crystal /Polycab/ Approved Make)
c) 100 A 415 V Porceline base Kit-Kat type switch fuse unit (make (Havels/Standard/Approved Make)
d) 100 A TPN Main Switch with re-wirable fuse link within sheet steel enclosure(make (Havels/Standard/Approved Make)
e) Supply and Delivery of 25 mm², 1.1 KV grade. 3.5 core Al Armoured XLPE conform to IS 1554/7098(part-I) 1998 (Make : Gloster /HAVELLS /MESCAB/ CURRENCY/POLYCAB/ CRYSTAL/ Approved Make)
Supply & delivery of following materials of best quality. a) 80mm. N.B. U.P.V.C. column pipe 7.1mm. thick having 70mm. long 8TPI threaded both side with heavy type socket & O ring biax technology with wiring lock system non corrosive high tensile having I.S.O. 9001 standard. (Make : Ashirbad/Raksha/ Approved Make).
i) 10ft. long (3mtrs)
ii) 5ft. long (1.5mtrs)
iii) 80mm. dia. top & bottom adaptor
iii) 3" x 2.5" M.S. Reducer
iv) 3 " dia. X 5 ft long M.S. (7.1 mm Thick) Column pipe having both side 11 TPI Thread and Socket.
b) Heavy type M.S. Suspension clamp of suitable dia. made of 80mm×10mm M.S. flat with nuts, bolts, washer etc.( suitable for 80mm. dia. column pipe)
c) Split type M.S. fabricated tube well cover for 150mm dia. tube well housing pipe with necessary fitting arrangement along with of column pipe, Air pipe, rope of anti snapping device & cable entry gland etc.
d) 102 mm. dia. 0-7 Kg./sq.cm. range, wall mounted pressure gauge. (Make: H. Guru/Febig/ Approved Make).
i) Tube well outside the pump house. (This cost includes 15mm. dia. G.I. pipe Tata medium of appx. 30ft. length & specials)
e) Anti snapping safety device made of suitable size & heavy type M.S. fabricated busket for resting the above pump set, with eye bolt/H. bolt 25.mm.dia. arrangement (4 ends), clamps for holding pump motor, Nuts & bolts etc. complete as per direction EIC. including 10mm.dia. stranded steel wire rope or 16mm dia. Nylone rope for hanging of anti snapping safety device as per direction of EIC.
f) 80mm.dia. CIDF Non Rising Spindle Sluice Valve (IS: 14846) with PN1.0 Pressure Rating as per I.S. specification & other required materials for the job i.e for completing the construction of delivery and wash out line.(Make:- IVI / UPADHYA / KIRLOSKAR/Durga/ Jupiter/MAGNET/CAIR/McWANE/Sigma Flow/ Approved Make). N.B: I) Test certificates for both valves should be submitted at the time of delivery. II) M. S. Specials should have minimum 7mm.Thickness.
g) Ø80 mm CIDF single door swing Non Return Valve (IS: 5312, Part-I) with PN1.0 Pressure Rating, (Make:-IVI / UPADHYA / KIRLOSKAR/Durga/ Jupiter/MAGNET/CAIR/McWANE/Sigma Flow/ Approved Make).
h) Ø 3 " X 2 ft CIDF Pipe
i) Ø 3 "Flanged tail piece
j) Ø 3"CIDF Bend
k)Steel Plug, M. S. Nipple, Flange, Nuts, Bolts etc
l) Ø 3 "M. S. Cross
Supply, delivery & fitting fixing of wall mounted 2mm.thick, CRCA sheet steel, powder coating finish painted, dust & vermin proof Manual panel suitable for pump, 5H.P. to 7.5H.P. in DOL operating mode, The panel shall be equipped by complete wiring with Amp. Meter, Volt. Meter, Starter etc. complete as per direction of EIC.
Making Brick Pillar for Supporting pipe line (10" X 10 " X 4 ft) by 1st class brick work with 4 :1 plaster and net cement punning complete including earth cutting, supplying necessary materials , ramming as per direction of EIC.
Drawing power line from old pump house to new pump house with supplied 100Amp. Kit-kat fuse and 25 mm², 1.1 KV grade. 3.5 core Al Armoured XLPE cable [item No. 3 (c&e)] including supplying necessary 2"x2" M.S. angle, Porceline insulator, G.I. wire, Nut Bolt etc. as per direction of EIC.
Installation of the item no. (3) to (5) [except item No. 3 (c&e)]with necessary connection complete including supply Copper wire, MS flange nut and Bolts Gasket & other fixing materials to complete the job and making platform of required size around T.W. with bricks, cement , sand stone chips etc(4:2:1) including plastering and net cement complete as per direction and entire satisfaction of the E.I.C.
Supplying & fixing compression type gland complete with brass gland, brass ring & rubber ring for dust & moisture-proof entry of 25Sq.mm. XLPE Armoured cables
Finishing the end of 25Sq.mm. 31/2 core XLPE Armoured cables by crimping method including supplying and fixing solderless socket (Dowels make), tapes, anticorrosive paste & jointing materials with including proper sealing of cable entry point
Making necessary non metalic pipe IS-14930 (80mm. dia.) protection for submersible cable from Tube well cover to inside of the pump house including supplying pipe, Elbow, Union, short piece, socket etc. complete for the job as per direction.
Double eathing with 50mm. dia. TATA – Medium G.I. pipe 3.64mm. thick × 3.04Mtr. long and 2×4SWG GI (Hot Dip) wire (4Mtr. long), 13mm. dia. × 80mm. long GI bolts, double nuts, double washers including supply & fitting 15mm. dia. G.I. pipe protection (1Mtrs. Long) to be filled with bitumen partly under the ground level and partly above ground level driven to an overage depth of 3.65Mtrs. below the ground level & restoring surface duly rammed.
Supply, delivery and storage at site of automatically controlled diaphragm type chlorinator dosing pump with flow rate 100 LPH and maximum pressure of 10Kg/CM2 with all accessories for pump & motor, foundation bolt, suction and discharge Flange and with storage tank of dosing solution of 100Ltr. Capacity and the prime mover to be coupled with pump of 0.5 H.P. 3 Phase, 1450 RPM squirrel cage TEFC induciton motor, Motor will be IE2/IE3 (Make of Machine : Swelore/Any other approved, Make of Motor : ABB / CGL /KEC / Any other approved make)
Installtion and commissioning of above supplied chlorinator with all accessories, PVC tank and drawing of power line as per IE rules by supplying of necessary wire and continuous earthing. This include the cost of all necessary CC foundation [at least 200mm height] with concrete mixture [sand, cement, stone chips] and neat cement finish by supplyig of all required materials and testing the entire set as per direction of EIC [power will be feed from PLC Panel of pumping machinery]
Distribution wiring in 1.1KV. Grade, (2X1.5mm2) single core stranded 'FR' PVC insulated & unsheathed copper wire (approved make) in suitable size PVC casing capping (Precision make) with (1.5 Sqmm) single core stranded 'FR' PVC insulted & unsheathed copper wire for ECC, including necessary PVC clips, fittings etc. to light/fan point with piano key type switch (anchor make) fixed on sheet steel fabricated switch board with Perspex/bakelite top cover on wall including necessary connections and making earthing attachment and mending good damages to building works. [PVC casing-capping and Switch board both on surface]
a) average run 4. 5 mtr. -
Supply and fitting fixing of 40A DP Isolator (Make : Havells/Standard)
Supply and delivery of CFL , 23 watt, (Make-phillips/ other approved make)
Supply and fitting fixing of Ceiling fan (Make: Usha /Crompton/Havels/ other approved make) 1200mm. sweep complete with blade, rubber bush etc. including supply and fixing 2×1/1.4 PVC copper wire for down rod with making necessary connection complete.
Supply & fitting fixing of 10 watt, LED Fixture set ----------for Phillips Model no. BRP 020/10 LED (Make: Phillps/ Other Approved Make) with 40mm. dia. × 2.5mtr. long G.I pipe bracket fixing on wall of the Pump House with 3nos. M. S. clamp properly grouting including making power connection with supply and drawing 2.5sq.mm. copper flexible cable wire with controlling sub switch and continuous earthing from nearest junction board all complete as per direction of E.I.C.
Supply of 4ft. 36W Double Fluorescent light fittings complete with all accessories including 2nos. 36W tube light incl. fixing light fitting on wall by means L clamp, nipple, suitable size fastner and connection by 1.5 sqmm PVC/Cu wire as to G S. Model :- TMC0552XTLD36WEBT ( Make- Philips/Havells/Bajaj/ other approved make)
Supply and fixing bulkhead light fittings on wall incl. connection. As to Gs .Make -Bajaj/Havells/ other approved make)
Add. GST@12%
Add. Cess@1%
BEHERA ENTERPRISE
M/S. SWAPAN BANERJEE
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .