Spl repair to OH LT line, UG LT cable at certain area of Khetrapal enclave, Spl repair/replacement of LT UG cable and feeder pillars at Tibri Mil Stn.

Amount

M&L for XLPE insulated, screened PVC bedded, galvanised steel strip or wire armoured heavy duty electic cable with stranded aluminium conductor 1100 volts grade cross sectional area 150 Sqmm 3.5 core laid in trenches/ ducts/ through pipes/ in floor road/ along the pole etc all as specified & directed by Engr-in-charge. Note : Excavation earth work, road cutting, brick protection, pipe and sand cushioning shall be measured & paid separately.

All as per srl item No. 1 here in before but 120 Sqmm 3.5 core

All as per srl item No. 1 here in before but 50 Sqmm 3.5 core

All as per srl item No. 1 here in before but 35 Sqmm 3.5 core

All as per srl item No. 1 here in before but 25 Sqmm 3.5 core

All as per srl item No. 1 here in before but 16 Sqmm 3.5 core

Taking out of LT UG cable from trenches/walls etc all as directed Note : Excavation earth work, road cutting shall be measured & paid separately.

Excavation in trenches in soft/ loose soil including taking out brick protection n.exc 1.5 m wide and n.exc. 1.5 m in depth for poles, stay, cable, pipe etc getting out all as specified.

Returning, filling in, including spreading, leveling,watering and well ramming in layers each n.exc 25 cm thick in soft loose soil all as specified.

Removal of excavated soil to a distance not exceeding 50 mtrs and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed.

Supply and lay brick common burnt sub class "B" old size for protection of cable laid in trenches for under ground cable all as specified.

M & L for Sand cushioning trenches using fine sand to under ground cable, laid in two layers before laying the cable & after laying the cable complete all as specified and directed.

Labour for drilling hole under the road with the help of bocki / by manual or by machine for crossing GI tubing of any size for cable protection all as specified and directed by EIC.

M&L for road cutting including excavation, returning filling in, spreading leveling, well ramming in layers, soling with broken boulders/ stones obtained from demolition of existing road, 7.5cm thick coarse aggregate obtained from demolition of existing WBM of road, watering and ramming, 40mm thick PCC 1:2:4 type B1 using 20mm graded stone aggregate for road patch repair work, Section/ cross section area of cutting shall be as specified and as directed by Engineer -In Charge.

M&L GI tubing light grade for cable protection fixed long the pole/under road/along the wall of size 80mm bore with necessary clamps all as directed. Note : Clamps, nuts and bolts will be measured and paid separately.

All as per srl item No. 15 here in before but 40 mm bore

M&L cable route indicator made out of MS angle iron of size 25x25x3mm thick 60cm long for HT/LT Cable" route marking embossed on MS circular plate 150mm dia 3mm thick including grouting in PCC 1 :3:6 type C1 block concrete of size 20x20x20cm including necessary earthwork and painting of exposed surfaces of MS angle iron using two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed

M&L for supplying, installing and commissioning of LT out door feeder pillar box double door type with neoprene rubber gasket, vermin/dust / weather proof, self ventilation on both side totally enclosed busbar, fully Comparted type front openable hinged independent door for each compartment with proper locking arrangement and common front and rear door openable with mild steel sliding door bolts 250 mm locking arrangement, made out of 3 mm thick CRCA sheet duly powder coated, 415 Volts, 50Hz properly welded and connecting the incoming/outgoing cable by providing cable glands and cable lugs including taking down existing panel complete all as specified and directed comprising of following accessories:-

M&L for supplying, installing and commissioning of LT out door feeder pillar box double door type with neoprene rubber gasket, vermin/dust / weather proof, self ventilation on both side totally enclosed busbar, fully Comparted type front openable hinged independent door for each compartment with proper locking arrangement and common front and rear door openable with mild steel sliding door bolts 250 mm locking arrangement, made out of 3 mm thick CRCA sheet duly powder coated, 415 Volts, 50Hz properly welded and connecting the incoming/outgoing cable by providing cable glands and cable lugs including taking down existing panel complete all as specified and directed comprising of following accessories:-

M&L for supplying, installing and commissioning of LT out door feeder pillar box double door type with neoprene rubber gasket, vermin/dust / weather proof, self ventilation on both side totally enclosed busbar, fully Comparted type front openable hinged independent door for each compartment with proper locking arrangement and common front and rear door openable with mild steel sliding door bolts 250 mm locking arrangement, made out of 3 mm thick CRCA sheet duly powder coated, 415 Volts, 50Hz properly welded and connecting the incoming/outgoing cable by providing cable glands and cable lugs including taking down existing panel complete all as specified and directed comprising of following accessories:- (i) 1 No. MCCB 100 Amp 4 pole, 16 KA with adjustable thermal and fixed Magnetic including spreader. (ii) Bus Bars : 200 Amp TPN aluminium. (iii) Volt meter 0 to 500 volts digital type inbuilt slector switch - 1 No

(iv) Ampere meter 0 to 100 Amp digital type inbuilt slector swtich - 1 No (v) LED Phase indicator lamp Set of three and tape wound CTs 200/5 -01 No (vi) All connections from MCCBs to bus bar & bus bar to MCCB shall be made with suitable size of aluminium strip thimble / lugs. (vii) All acessories prewired with copper conductor cable single core 2.5 Sq mm multistranded PVC insulated with copper thimble / lugs etc all as specified and directed. (viii) Frame, pedestal legs (4Nos) made of MS angle of size 40x40x6 mm of length 750 mm, 300 mm below the ground and 450 mm above the gound level grouted in PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) block of suitable size.

M&L for supplying, installing and commissioning of LT out door feeder pillar box double door type with neoprene rubber gasket, vermin/dust / weather proof, self ventilation on both side totally enclosed busbar, fully Comparted type front openable hinged independent door for each compartment with proper locking arrangement and common front and rear door openable with mild steel sliding door bolts 250 mm locking arrangement, made out of 3 mm thick CRCA sheet duly powder coated, 415 Volts, 50Hz properly welded and connecting the incoming/outgoing cable by providing cable glands and cable lugs complete all as specified and directed comprising of following accessories:-

Demolition of existing earthing complete all as specified & directed by Engr-in-charge.

M&L earthing complete with galvanised steel earth plate electrode 60×60cm×6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised iron 25x4mm earth lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No.3 connected to earthing test point including testing on completion including watering GI pipe 20mm bore medium grade, 15mm bore light grade GI pipe for protection of earth lead including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 54 cm x 54 cm x 5 cm including 8mm dia TMT bars both ways @ 15cm centre to centre with one handle for lifting made out of 8mm dia MS bar, funnel & wire mesh, excavation and earth work in any type of soil complete all as specified & directed by Engr-in-charge.

Demolition of ACSR Conductors any size complete all as specified and directed

Demolition of cross arms of MS channel or angle section D Clamp etc, insulator complete all as specified.

S&F in repair junction box size 170x 170x105mm poly corbonate with glass fibre reinforced , environment friendly, recylable, UV resistant , halogen and silicon free anti acid and anti corrosive IP 66/67 in accordance with IE rule internally embedded gasket, junction box including 3 phase 415 volt aluminium bus bar and one No. MCB SP 6A 10KA to control the street light including necessary clamps, nuts bolts to fix the junction box with poles all specified and directed.

Supply and fixing of two single core PVC insulated cable with stranded copper conductor of size 2.5 sqmm fixed in and incl non metallic PVC conduit including fixing accessories of conduit i.e clamp , Nut & Bolt complete all as specified

Supply and fixing in repair new generation energy saving IP 66 street light luminiaries with long life versatile pressure die-cast aluminium road way luminaire complete all accessories, connecting up with twin core twisted flexible copper conductor cable all as specified & directed with high power LED 72 watt , warm light , aerodynamically designed with better thermal management .

S&F GI pipe bracket made out of GI pipe light grade 32 mm bore and bent to shape 1.5m long, MS clamps made out of MS flat iron of size 40mm x 5mm thick and drilling of hole for and including nuts, bolts and washers including painting MS clamps with two coats of synthetic enemal paint over a coat of red oxide primer including taking down the existing GI pipe bracket complete all as specified and directed.

Supply and fixing of three phase 5 KW Automatic Street Light Control Switch using Infrared Sensor based NATURE SWITCH for automatic switching of Street lights. Nature switch operation should be based on Natural Light Lux level. Switching on illuminance level should be of minimum 30 Lux and Switching off illuminance should be greater than or equal to 10 Lux. The sensor should also have part night operation facility of min 4 hrs to maximum 12 hrs. The circuit shall have a provision for manual over ride operation. The sensor along with suitable power contactors and incoming-outgoing MCBs should be enclosed in a pole/wall mountabl enclosure made of rust proof, electric shock proof, termite proof and FR grade SMC junction box conforming to IP54 complete all as directed by Engr-in-Charge.

M & L cross arm, bracings, supports, clamps and back plates fabricated from structural steel sections including clamps, nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of paint. Note: Unexposed surface shall be given one coat of primer only

A Schedule of Credit for old/unserviceable demolished/dismantled items has been catered for in the tender. The Schedule of Credit is pre-priced by MES. The final amount of the tender shall be arrived at after deducting the total amount of Schedule of Credit from the total amount of BoQ as per General Summary sheet catered for after Schedule of Credit.

dinesh enterprises

sanjeev enterprises

P S BUILDERS