SPECIAL REPAIRS AND ADDN/ALTN TO BLDG NO EM-99 PROVN OF DUTY OFFICER AND DUTY JCO ROOM IN WORKSHOP AREA PROVN OF 39 STEEL PLATE RACK IN MD ACCN PROVN OF INTERLOCKING TILES IN 475 ENGRS BDE SPORT COMPLEX AND PROVN OF TOILET BLOCK FOR MAIN OFFICE CO

Amount

Excavating in trenches, not exc 1.5m wide and not exc 1.5m in depth; for foundation etc.and getting out in any type of soil, complete all as specified & directed.

Filling soil under floor including spreading levelling watering and well ramming in layers n exc 25 cm thick complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in any type of soil, complete all as specified & directed.

M & L for removing excavated soils n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and directed.

M & L for PCC 1:4:8 Type D2 using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and as directed.

M & L for mild steel TMT bars of 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L for mild steel TMT bars 5mm dia and over upto including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L for RCC M-25 grade (design mix) using 20mm graded aggregates as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc complete all as specified and directed.

M & L for formwork to sides of concrete foundations, footings, bases of columns, raft and beams, sides and soffits (if any) of foundation and plinth beams , and similar work, vertical or to batter, flat surfaces of concrete , surface is required to be fair finished complete all as specified and directed.

M & L for M-25 grade (design mix) using 20mm graded aggregates as in columns, pillars, piers, posts and struts complete all as specified and directed.

M & L for formwork to sides of pillars, posts, struts, piers, columns and stanchions, rectangular or polygonal surfaces of concrete , surface is required to be fair finished. complete all as specified and as directed by the Engineer-in-Charge

M & L for RCC M-25 (design mix) using 20mm graded aggregates as in roof beams, lintel beams/bands, cantilevers, bressummers, lintels over 1.5m span, chajjas etc complete all as specified and as directed by the Engineer-in-Charge.

M & L for formwork to sides and soffits of floor or roof beams, soffits of lintel beams/ bands, chajjas, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports overhangs etc, also splays between floors and beams, etc., flat surfaces of concrete , surface is required to be fair finished. complete all as specified and as directed by the Engineer-in-Charge

M & L for RCC M-25 (design mix) using 20mm graded aggregates as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed by the Engineer-in-Charge.

M & L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), flat surfaces of concrete , surface is required to be fair finished complete all as specified and as directed by the Engineer-in-Charge.

M & L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide, as roughed finished surface of concrete complete all as specified and as directed by the Engineer-in-Charge.

Demolition of stone/ brick masonry built in cement or cement lime mortar as in portion ordered and directed.

M & L for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and as directed by the Engineer-in-Charge

All as item No. 18.00 above but except stone.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, hammer dressing with maximum depression on face from straight edge held against the dressed surface n. exc 20mm complete all as specified and as directed by the Engineer-in-Charge

M & L for brickwork with fly ash bricks, in straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and as directed by the Engineer-in-Charge

Supply only Integral waterproofing compound complete.

M & L for roof treatment with APP modified polymeric water proofing membrane, 2mm thick having centre core not less than 100 micron high molecular high density polyethylene film (HMHDPE) film protected from both sides with high polymeric asphaltic mix and 20 micron HMHDPE film weight not less than 3 Kg / Sqm applied with bonding material using blown type bitumen conforming to IS-702 Grade 85/25 @ 1.20 Kg/ Sqm over bitumen primer conforming to IS- 3384 @ 0.40 Kg/ Sqm with final coat of bonding bitumen grade 85/25 @ 1.20 Kg/ Sqm over APP membrane with all overlaps complete all as specified and as directed by the Engineer-in-Charge

M & L for rendering 10mm thick in CM 1:4 on fair faces of brick work or concerte surfaces whilst concrete is green mixed with WPC as per manufactureres instructions, finished even and smooth (without using extra cement) complete all as specified and as directed by the Engineer-in-Charge.

M & L for 40mm thick (average consolidated thickness) PCC (1:2:4) type B-0 using 12.5mm graded stone aggregate laid in slope as in padding, finished even and smooth on existing slope including provision of 'V' shaped groove 6mm wide and 10mm deep at 0.60 metre interval or parts thereof, both ways on top of PCC padding and filled with mastic bitumen of (1:1) proportion Without using extra cement, complete all as specified and directed.

M&L 10mm thick redering on brick work surfaces in CM 1:6 finished fair and even without using extra cement complete all as specified and directed.

M&L for 10mm thick rendering on brick work or concrete surface in cement mortar (1:4) as on ceiling surfaces finished fair and even complete all as specified & directed.

M & L for rendering 15mm thick in cement plaster 1:4 on fair faces of brick work or concrete surfaces even & smooth without using extra cement complete all as specified and directed

M & L for preparing new surfaces (plastered) of walls and applying two coats of cement base paint over a coat of cement primer complete all as specified and directed

M & L for rendering 15 mm thick in cement mortar 1 : 6 on fair faces of brick work or concrete surfaces including finished even & smooth surfaces without using extra cement complete all as specified and directed

M&L for preparation of new plastered surfaces of walls and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer over & including 1mm thick finished coat white wall care putty complete all as specified and directed. (Make-Birla/JK/Asian)

M & L for preparing new plastered or unplastered surface of walls and applying three coats of white wash as on walls complete all as specified and directed.

M & L for rendering 10mm thick in cement plaster 1:3 on fair faces of brick work or concrete surfaces , in ceilings, finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

M&L for preparation of newly plastered surfaces of ceilings & applying three coats of white wash complete all as specified.

M&L for non skid ceramic coloured tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, 7 to 8mm thick in floors set and jointed in neat cement slurry and pointed in coloured cement to match the shade the tiles over 15mm thick screed bed in CM 1:6 over and including 25mm thick PCC 1:2:4 at B-0 (using 12.5mm graded stone aggregate ) complete all as specified and directed.

M&L for glazed ceramic colour tiles in vertical surface 350x450x7-8 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match fixed over and including 10mm thick CM (1:4) as in backing coat all as specified & directed.

M&L for 25mm thcik PCC (1:2:4) type B-0, using 12.5mm garded aggregates as in base concrete to floor finish all as specified and directed.

M & L for Non-Skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of Each tiles exceeding 0.11sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match fixed over and including 15mm thick screed bed CM (1:6) complete all as specified and as directed.

All as per the item No 38.00 above but as in skirting over 10 mm screed plaster in CM 1:4 complete all as specified and as directed by the Engineer-in-Charge

M & L for machine cut kota stone slab as in shelving/ window cills or steps 25mm thick in single piece over 15mm thick screed bed CM (1:6) incl necessary bull nosing fixed to wall and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing on both face complete all as specified and as directed by the Engineer-in-Charge

M & L for 100 mm thick cement concrete type D-2, 1:4:8 using 40mm graded aggregate , as in sub base. complete all as specified and as directed by the Engineer-in-Charge

M&L for machine cut Kota stone slab flooring 20-25mm thick over and including 15mm thick screed bed in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab with 100mm wide white marble strip in border as directed by Engr-in- charge, including rubbing and polishing complete all as specified.

M & L for kota stone slab 20-25mm thick in riser, skirting, and pillar laid over & incl cement screed base 10mm thick in CM (1:4) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing & incl necessary bull nosing complete all as specified and as directed by the Engineer-in-Charge

S&F factory made pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, mild steel sheet of 1.25 mm thickness, complete as specified & as directed.

S & F second class HW Hollock/Bonsum/Sal 35mm thick, factory made, plain framed, panelled shutter (Three panels) with panels of 9mm thick BWR grade ply wood bonded with high quality liquid phenol formal dehyde synthetic resin adhesive conforming to IS-303. The size of rails & style shall be as per IS-1003 (part-I) kiln seasoned as per IS-1141 & chemically pressure treated as per IS-401 complete all as per specified and directed.

S & F IInd Class HW 35mm thick glazed and skeleton factory made shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.20 (a) supplied and fitted to chowkats.

S & F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with M.S. square tube and fixing in opening as per specification & drawing complete all as specified and as directed by the Engineer-in-Charge

Supply and fixing of 30mm thick factory made solid panel PVC door shutter (style) consisting of frame made out of MS tubes for top and bottom rail. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded. sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement, complete all as specified and directed.

S & F factory made solid PVC moulded door shutter of approved colour with particle board core, 28 to 30mm thick (stiles), with 2, 4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm thick plain colour PVC sheet on back face, fixing in frame at site as per specification & drawing complete all as specified and as directed by the Engineer-in-Charge

S & F 150mm long aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed by the Engineer-in-Charge

S&F 125mm long aluminium handle, cast type, anodized, ISI marked, complete all as specified and as directed by the Engineer-in-Charge.

S & F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed by the Engineer-in-Charge

S&F of MS butt hinges 100 mm size (ISI Marked) medium weight, cold rolled mild steel all as specified

S & F 300mm, M S ordinary rat tail rod pattern springs including roller and roller plate complete

M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified.

S & F Steel window/ventilator factory made, out of MS hollow section 79mm x 39mmx1.6mm thick frame with double shutter (glazed & wiregauged shutters) made out of Z section using flush butt welding and tennon riveting all as per IS 1038/83, dobby hinges shall be provided to both shutters, Locking arrangements as per sample approval by GE, provided with knob, 10mm MS square bars in grill, Z section handle 100mm size and 150mm long hook & eye welded to frame and shutter, four Nos lugs welded to frame inculding necessary flat iron beading for securing wire gauge etc including holes, cutting holes for hold fast and making good in PCC 1:2:4 type B-1 complete all as specified and directed. Note : Wire mesh and sheet glass shall be measured & paid separately under respective items.

S&F Steel window/ ventilator glazed and gauged (combination) with side hung/ top hung shutters incl box type / projecting type hinges, and steel peg stay, handle & locking arrangement and frame made out of 1.25mm thick pressed steel frame complete incl necessary AC/Cooler arrangement in window & guard bars complete all as as specified and directed.

S & F for 3.0mm thick pin head type and glazing with oil putty in squares n exc 0.5 sq m in each pane complete all as specified and as directed by the Engineer-in-Charge.

S & F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed by the Engineer-in-Charge

M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of zinc chrome primer complete all as specified.

S & F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors and fixed to wall with clamps complete all as specified and as directed by the Engineer-in-Charge

S & F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed by the Engineer-in-Charge

S & F for 110mm bore PVC (SWR) junction single (Single T) equal or unequal with oval access door, complete all as specified

S & F 75mm bore PVC (SWR) bends of any radius with oval access door, complete all as specified

S & F 110mm bore PVC (SWR) bends of any radius with oval access door, complete all as specified

S & F 110mm bore PVC (SWR) vent cowl complete all as specified and as directed by the Engineer-in-Charge

M & L for PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and as directed by the Engineer-in-Charge

M & L for 75mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed by the Engineer-in-Charge

S&F vitreous china wash hand basin white flat, back of size 580mm x 450mm including 32mm waste coupling and PVC waste down pipe and bracket complete all as specified and directed.

S & F of vitreous China urinal, flat back, half stall type white/ ivory colour with grating and Union for discharge pipe. Including connection to flushing pipe and outgoing waste pipe complete all as specified and as directed by the Engineer-in-Charge.

S & F sheet glass shelf assembly consistinf of 5.5 mm thick glass shelf 12 cm wide with chromium plated brackets guard and railing 60 cm long complete all as specified and as directed by the Engineer-in-Charge

S&F 15mm dia pillar taps cast copper alloy with capstan heads, cromium plated screwed down high pressure with or without lettered Hot or Cold with long screw shanks abd fly -nuts screwed for iron pipe and fixed complete all as specified and as directed by the Engineer-in-Charge

S&F vitreous china wash down water closet pedestal pattern pan white with trap including connection to existing out joint pipe, flushing pipe or Cistern, antisyphonage pipe, including making, etc complete including making goood to floor etc complete all as specified and as directed.

S&F 10 ltrs capacity PVC Valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets low level flushing cistern and connections to pipes and incl suitable flushing pipe for connection into WC, if any all as specified. complete all as specified and as directed by the Engineer-in-Charge

S & F of 15mm size PVC connections with PTMT nuts of length 450mm complete all as specified and as directed by the Engineer-in-Charge

Dismantling of existing unserviceable water tank of any description capacity exc 500 Ltr but n.exc 1000 ltrs capacity Each complete all as specified and directed

Supply and fixing 500 Litre capacity, white colour rotational moulded polyethylene water storage tanks triple layered (cylindrical vertical with closed top) , hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.

Supply and fixing 1000 Litre capacity white colour rotational moulded polyethylene water storage tanks triple layered (cylindrical vertical with closed top) , hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.

S & F of for ISI Marked 20mm dia Ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and as directed by the Engineer-in-Charge.

Taking up or down steel tubing and connection 15 mm bore and removing the same from site/keeping aside for reuse complete all as specified and directed.

All as per srl item No. 82.00 above but 20 mm bore

All as per srl item No. 82 above but 25.00 mm bore

S & F 25mm bore tubes medium grade galvanised, with all necessary fitting and fixed complete to walls and ceilings or laid in floors complete all as specified.

S & F 20mm bore tubes medium grade galvanised, with all necessary fitting and fixed complete to walls and ceilings or laid in floors complete all as specified.

S & F 20mm bore tubes medium grade galvanised, with all necessary fitting and fixed complete, laid in trenches complete all as specified.

S & F 15mm bore dia tubes medium grade galvanised, with all necessary fitting and fixed complete to walls and ceilings or laid in floors complete all as specified.

Fixing only 15mm bore old GI tubing to walls, ceiling or laid on floor including necessary cleanig, cutting, screwing and new fittings such as elbow, Tee, union, socket, reducer etc complete all as specified and as directed by the Engineer-in-Charge

All as per srl item No. 89.00 above but 20 mm bore

All as per srl item No. 89.00 above but 25 mm bore

S&F 25mm Gate Valves (gun metal, with iron wheel) screwed both ends for iron pipes and fixed complete all as specified and as directed by the Engineer-in-Charge

S&F 20 mm Gate Valves (gun metal, with iron wheel) screwed both ends for iron pipes and fixed complete all as specified and as directed by the Engineer-in-Charge

S&F in repairs 25mm Gate Valves (gun metal, with iron wheel) screwed both ends for iron pipes and fixed complete all as specified and as directed by the Engineer-in-Charge.

Cutting existing steel tubing for addition and alteration, screwing the existing steel tubing in position and insertion of required size of GI fittings (ie union, nipple, reducing tee) for branch connection of internal dia 25/20mm complete all as specified and as directed by the Engineer-in-Charge.

S & F of 15mm bore dia bib Bib taps, cast copper alloy fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed by the Engineer-in-Charge

S&F in repairs Chromium plated bib taps, with capstan heads, screwed down for iron pipe or for brass ferrule & fixed for 15 mm bore pipe complete all as specified & directed.

S & F 15mm bore dia stop valves/angle cock, cast copper alloy, fancy type, chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed by the Engineer-in-Charge

S & F 15mm bore dia stop valves/angle cock, cast copper alloy, fancy type, chromium plated with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed by the Engineer-in-Charge.

S & F brass chromium plated swivel shower rose 125mm size, including fixing to steel pipe or union complete all as specified and as directed by the Engineer-in-Charge.

S & F tubular towel rail of brass Chromium plated, 20mm dia, D type 60cm long between flanges including Chromium plated brass screws and wooden/plastic cleats complete all as specified and as directed by the Engineer-in-Charge.

S & F for brass chromium plated soap dish, fixed to plugs with chromium plated brass screws complete all as specified and as directed by the Engineer-in-Charge.

M & L for hardcore of broken stone or boulders gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and remmed to a true surface, complete all as specified & directed.

M&L for 50 mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3) complete all as specified and as directed by the Engineer-in-Charge.

M & L for 75mm thick cement concrete type D-2 1:4:8 using 40mm graded aggregate as in sub base of floor, complete all as specified and as directed by the Engineer-in-Charge.

M&L for factory made 60mm thick machine pressed precast cement concrete coloured, reflective type interlocking paver blocks of Grade M-35 conforming to IS 15658-2006 of shape and size as directed with grey cement and pigment laid over & including 50 mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator complete all as specified & directed.

S&F mild steel framed work such as grills, guard bars, barred iron doors, cooler stand, framework of water tanks and similar works, conforming to Grade E-165 (Fe 290), including welding etc complete all as specified and as directed by the Engineer-in-Charge.

Taking out old grill and S&F new mild steel framed work such as grills, guard bars, barred iron doors, cooler stand, framework of water tanks and similar works, conforming to Grade E-165 (Fe 290), including welding etc. complete all as specified & as directed.

M & L for 100 mm internal dia pipe cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required, complete all as specified and as directed by the Engineer-in-Charge.

S&F stainless steel Kitchen plate rack of overall minimum size 920mm x 785mm and 255mm deep, with partitions for small/large plates etc made out of stainless steel sheet 1m thick , fixed with rawl plug and CP steel screws complete all as specified and as directed by the Engineer-in-Charge. Note : Weight of rack shall not be less than 7.00 Kg/Each.

All as per description of serial item No. 110.00 above but fixed in repairs.

S & F for sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to rigid UPVC waste pipe bent to shape & fixed to wall with bracket overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed by the Engineer-in-Charge

S&F plain sheet glass ordinary quality 3mm thick fixed with oil putty size of glass n exc 0.50 Sqm in each pane complete all as specified and directed.

S&F aluminium anodised barrel tower bolt 150mm long of extruded section complete all as specified and as directed by the Engineer-in-Charge.

S&F aluminium anodised handle 150mm long fabricated type complete all as specified and directed.

S&F Aluminium anodised hinges medium weight of size 100mm complete all as specified and directed.

M&L 40 mm thick sand stone slabs; set and jointed over joists etc. in CM 1:4 as in cover slab surfaces even & smooth complete all as specified and directed.

S&F salt glazed stone ware drain pipes of 150mm bore, grade `A’, ISI marked, laid to slope in trenches, jointed in CM (1:1) and tested complete all as specified.

M&L for PCC 1:4:8 type D-2 using 40 mm graded crushed stone aggregate in bedding to SGSW drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested complete for 150 mm bore pipe complete all as specified and as directed by the Engineer-in-Charge.

M&L for LLDPE Septic tank designed to carry sewage and sludge water , excavation in any type of soil In PCC 1:4:8 below foundation ,vent shaft ,connection, etc., complete for 10 users, complete, all as specifie and directed..

M&L for construction of soakage wells, excavation in any type of soil, foundation in PCC 1:3:6, wells of noney combed and solid in M-25 Concrete, including intercepting chamber, screen chamber, brick work in CM, RCC cover slab in M-25/ RR masonry / Filling with brick bats, complete of size 1.2 M dia X 3.0M deep etc complete all as specified and shown in drg No. CEBZ/TD/78/2011, sheet 1 & 2 and as directed.

Taking down cement or cement lime plaster on stone/brick wall, ceiling including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M& L for 15 mm thick rendering in cement mortar (1:6) on stone masonary surfaces finished fair and even complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on stone masonry, external surfaces finished fair & even complete all as specified and directed.

Dubbing out average 10mm thick in CM 1:4 on irregular faces of walls or concrete chajjas etc complete all as specified and directed.

M&L for preparation of old plastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed

M&L for preparation of old plastered surfaces of wall and applying three coats of white wash complete all as specified and directed

M&L for preparation of old decorated surfaces of walls and providing one coat of cement base paint complete all as specified and directed.

Demolition of cement concrete (unreinforeced) in floors and paving n.exc 15cm thickness (above or below ground level) complete all as specified and directed.

M&L for PCC 1:2:4 Type B-1 (using 20mm stone crushed agg.) as in rounded or chamfered on edges in any description complete all as specified.

Demolition of stone slabs & tiles of any description or thickness in floors, aprons etc, complete all as specified and directed.

M&L for 20mm thick black granite on kitchen platform and similar work over & including 15mm thick screed bed in CM 1:6 laid over sand stone slab machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing complete all as specified & directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n exc 1.50 sqm Each and removing from site complete all as spd & directed and making good disturbed surface of walls in cement mortar (1:3) all as spd and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm and n.exc 4.00 Sqm Each and removing from site complete and making good disturbed surfaces of wall in CM (1:3) all as specified and directed.

M & L for rolled mild steel work angle iron as in door frame (Chowkhats) & cooler stand including provn of 12mm dia deformed bar welded horizontally to bottom of frame confirming to Fe-290 or Fe-330 including preparing back of chowkhat and applying two coats tar and sanding newly tarred surfaces with clean sharp sand complete all as specified and directed.

M&L for 18/19mm thick block board grade-.II quality, interior grade with decorative type with decorative face veneer on both face fixed complete, including teak wood lipping 19 x 6mm thick fixed with nails in shelves, partition and palmet boxes, shelves, almirah book cases, toilet boxes, racks, cup board shutter and similar works all as spepcified and directed.

S & F continuous (piano) hinges, mild steel, bright finish width of flaps (when open ) 40 mm all as specified and directed.

M&L for IInd class H/W Plain , Solid , Straight chowkats and frames sec area n exe 40 sqcm complete and all as specified..

S & F 100mm size hasp and staple, aluminium anodised safety type, fixed with screws complete all as specified and directed

S & F 75mm size hasp and staple, aluminium anodised safety type, fixed with screws complete all as specified and directed

S & F in 50 mm dia polished hardwood knobs fixed with screws complete all as specified and directed.

S & F 125mm double action spring hinges,mild steel with steel wire spring, stove enaelled black, complete all as specified and directed.

M&L for 50 mm thick sand stone slabs; set and jointed over joists etc. in CM 1:4 as in base of water tank and M&L 25 mm thick PCC 1:2:4 type B-0 (using 12.5mm stone crushed agg.) finished concrete surfaces even & smooth complete all as specified and directed

Dismantling Asbestos Cement (corrugated, semi corrugated, etc) sheets in roof covering complete all as specified & directed.

S & F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws/ Lor J type hook complete all as specified & directed.

S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws/ Lor J type hook complete all as specified & directed.

M&L for PCC 1:3:6 type C1 using 20 mm graded stone aggregate as in surface channel and drain etc complete all as specified.

Taking down CI pipe 100/75 mm fixed wall and floor etc including accessories complete all as specified and directed.

S&F CI soil and waste pipe 100mm bore waste or vent pipe in any length with or without ears, with cement joints on vertical surfaces of wall complete all as specified and directed.

Fixing only 100 mm bore old CI pipe as on wall with fixing accessories .

S& F 100 mm CI soil waste and vent pipes single socketed in any length with cement joints laid in floor or in trenches complete all as specified and directed

S& F 75 mm CI soil waste and vent pipes single socketed in any length with cement joints laid in floor or in trenches complete all as specified and directed

S& F 75 mm CI soil waste and vent pipes single socketed in any length with or without ears, with cement joints on vertical surfaces of wall complete all as specified and directed.

Fixing only 75 mm bore old CI pipe as on wall with fixing accessories .

S& F 75 mm CI bend, fixed with cement solvent complete, all as specified and directed

S& F 100 mm CI bend, fixed with cement solvent complete, all as specified and directed

M&L for PCC 1:3:6 , type C-2, using 40mm graded crushed stone aggregate as in foundation, filling and mass concrete, including necessary formwork, complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fittings such as switches, ceiling roses, holders, regulators, sockets etc., removing materials from site and making good disturbed surface of walls, floors etc.

Taking down MCB DB's complete with MCB's/Isolator etc removing materials from site and making good disturbed surface of walls, floors etc.

M&L for point wiring with 1.5 Sqmm, PVC insulated, unsheathed, multi stranded copper conductor single core FRLS cable, IS-694 marked, drawn through and including non metallic rigid PVC concealed conduit 20mm dia or higher complete with all PVC conduit accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc./ fittings ISI marked and sunk type pressed steel anodised terminal box 1.2 mm thick with bakelite laminated sheet top cover 3 mm thick( Make - Hylem/Anchor) ISI Marked, brass screws and cup washers including 1.5 Sqmm multi stranded copper conductor PVC insulated green in colour as continous earth conductor connected to common earth and earth dolly with all accessories complete all as specified and directed for:- Make of wire- Havells/Polycab/Anchor/Finolex. Make of PVC conduit -AKG/Plaza/Kalinga

One light point/bell point controlled by one, one way switch.

One ceiling fan/exhaust fan point controlled by one, one way switch.

One three pin 5 Amp socket on same board with other switches.

One 3 pin 5 Amp socket on independent board.

All as per item No. 160.00 here-in-before but with 2.5 Sqmm, for one 5 pin 5/15 Amp socket on independent board including 2.5 Sqmm stranded copper conductor (FRLS) PVC insulated green in colour as continous earth conductor connected to common earth.

S&F Switch piano, flush type, single pole, one way, 5 Amps, 240 volt, 50Hz, AC, complete all as specified and as directed by Engr-in-Charge. MAKE:-Havells/Anchor/Legrand

S&F switch piano flush type 15 amps, single pole one way 240 volts complete all as speciied and directed by Engr-in-Charge.MAKE:-Havells/Anchor/Legrand

S&F Socket outlet 3 Pin 5/6 Amp flush type complete all as speciied and directed by engr-in-Charge. MAKE:-Havells/Anchor/Legrand

S&F socket out let 2 in 1,multipurpose 3 pin 15/16 Amp flush type complete all as speciied and directed by Engr-in-Charge. MAKE:-Havells/Anchor/Legrand

S&F ceiling fan regulator electronic flush , steped type (four step) 230 Volts AC complete all as speciied and directed by Engr-in-Charge. MAKE:-Havells/Anchor/Legrand

S&F ceiling rose surface bakelite 3 terminals 63.5 x 17 mm complete all as speciied and directed by engr-in-Charge .MAKE:-Havells/Anchor/Legrand

S&F LED tube light fitting in acrylic linear tube (1x 18 watt),230V for single LED tube light including 1 x 18 W LED retrofit bar professional CW 6500 K cover channel, bipin holders,LED power driver, connector block, etc complete with all accessories internally prewired and including connecting up with three core flexible copper conductor cable with suitable size for connection of fitting from ceiling rose complete all as specified and directed. Make Havells Cat part NoPHOTONULTRA2.01212T8SSTL20WLED 865SPC (for tube) REGALBATTENT8UPTO1X22WDSBSWH (for batten)Bajaj Cat Part No BLRB 18W CWc for tube , BLRB - DB 118 for batten , or equivalent model of Philips/Crompton

S&F of lamp holder PVC/polycarbonate type with back plate complete all as speciied and directed by Engr-in-Charge. MAKE:-Havells/Anchor/Legrand

Supply and fixing LED lamp 10 watt suitable for 230 volts , 50 Hzs, B-22 base complete all as specified and directed. MAKE:-Havells/Bajaj/Philips

S & F LED light fitting 1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engr-in-Charge. Make Bajaj/Havells/CG

Supply and fixing testing and commissioning energy saving street light luminaire 35 watt LED , aluminium pressure die cast housing with tughened glass cover with individual LED lence , IP 66 protection complete all as specified and directed by Engr-in-Charge. Make- Havells Cat Part No ENDURACITYLITEPLAT PLUSSL35WLED757SASYBOPC or equivalent model of Surya/Control& Switchgear/Bajaj

Supply and fixing street light bracket made of 32 mm GI pipe , 1.2 mtr lenght fixed with two nos of clamp , nut and bolts complete all as specified and directed.

Taking down existing ceiling fan , dismantling blades and refixing after cleaning incl conecting up with three core flexible cable from ceiling rose to fancomplete all as speciied and directed by Engr-in-Charge.

M& L for painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc

S&F of MCB distribution board TPN 4 way, 415 volts, double door, with 200 Amps rated bus bar, neutral bar with shrouds, earth bar, IP-43 , made out of sheet steel enclosure, recessed type, factory made powder coated suitable for housing MCBs as incomer and outgoing including blanking plate complete all as specified and directed by Engr-in-Charge. Make: Legrand/Schneider/Seimens Note: MCB DB and MCB SP/SPN will be of same make.

S&F MCB distribution board single pole & neutral with 200 Amps rated bus bar, double door IP-43 DB's , made out of sheet steel enclosure, recessed type, factory made powder coated 8 way, 240 volts suitable for housing MCB's including blanking plate complete all as specified and directed. Make: Legrand/Schneider/Seimens Note: MCB DB and MCB SP/SPN will be of same make.

S & F of MCB SP, 240 volt, 3 Amp to 32 Amp capacity, 10 KA, 'C' curve complete all as specified and directed by Engr-in-Charge. Make : Legrand (DX-3), Schneider (Acti-09), Siemens ( Betagard)

S & F MCB SPN, 240 volt, 63 Amp capacity, 10 KA, 'C' curve complete all as specified and directed by Engr-in-Charge by Engr-in-Charge. Make : Legrand (DX-3), Schneider (Acti-09), Siemens ( Betagard)

S & F MCB TPN, 240 volt, 63 Amp capacity, 10 KA, 'C' curve complete all as specified and directed by Engr-in-Charge by Engr-in-Charge. Make : Legrand (DX-3), Schneider (Acti-09), Siemens ( Betagard)

Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion complete all as speciied and directed by Engr-in-Charge.

Supply and fixing of hook made of anodised flat iron for hanging of ceiling fan suitable for roof complete with nut, bolts MAKE:-Havells/Anchor/Legrand

Supply and fixing tubes light grade GI tubing 40 mm dia with all fitting laid in trenches Make : TATA/JINDAL/Swastik

Supply , laying and testing 1100 volt grade heavy duty cable XLPE insulated , armoured cable with stranded aluminium conductor of size 10 Sq mm 2 core including taking down old unsv cable complete all as specified and diected .Make Havells/Polycab/Asian/Gloster/Finolex

Supply , laying and testing 1100 volt grade heavy duty cable XLPE insulated , armoured cable with stranded aluminium conductor of size 16 Sq mm 4 core including taking down old unsv cable complete all as specified and diected .Make Havells/Polycab/Asian/Gloster/Finolex

M&L for filling clean and dry sand cushioning for cable in trenches all as specified and directed.

Supply and laying of bricks old class ‘B’ as protect on to UG cable laid flat adjoining to each other width wise all as specified.

S&F LED mirror light fitting 10 watt sleek polycarbonate channel with white acrylic cover complete with all accessories pre-wired and including connecting flexible copper conductor cable with suitable size. Make: Havells/Bajaj/Crompton.

S&F ceiling fan complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep, Min air delivery 210 CFM with service value 6.00 BEE, 5 star rated with brushless direct current motor (BLDC) complete, all as specified and directed. Make: Havells/Bajaj/Crompton.

S&F storage type water heater (Geyser) electrical operated 230 Volts including connecting inlet/outlet/vent pipes, electric/earth connections, mounting bolt, nuts and carrying out testing for proper functioning of all as directed by Engr-In-Charge. Make: Usha/Crompton/Bajaj

S&F exhaust fan made of sturdy engineering plastic complete with louvers shutter, voltage 230 V, 50 Hz, RPM 1200 Copper winding of sweep 300mm complete all as specified & directed.Make: Usha/Crompton/Bajaj

S&F exhaust fan made of sturdy engineering plastic complete with louvers shutter, voltage 230 V, 50 Hz, RPM 1200 Copper winding of sweep 450 mm complete all as specified & directed.Make: Usha/Crompton/Bajaj

Surface dressing not exc 15cm deep in soft/loose soil.

M&L for precast cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in kerb block (factory casted) with plain fair faces, including weathering, slightly rounded or chamfered angle throating, with plain or interlocking joints and setting in cement mortar 1:4, complete, all as directed.

M&L for preparation of new concrete surfaces of Kerb stone etc over 10cm in width or girth and applying two coats of synthetic enamel paint, alternate in black & white tint, all as specified & as directed.

M/s S. K. Construction Co.

M/s Jai Jinendra Constructions

M/s SUNIL ENTERPRISES