SPECIAL REPAIR OF OFFICERS MESS P-22 OF 15 INF DOU AND TOILET BLOCK OF BLDG NO P-1/1 OF 173 MD REGT AND PROVN OF HARD STANDING FOR CAR PARKING NEAR DIV HQ UNDER GARRISON ENGINEER AMRITSAR CANTT

Amount

AC/SRW(BLDG)-04/2023-24 Dismantling of roof brick tiles fixed in cement mortar in single layer ; Complete all as specified and directed by Engineer-in-Charge.

Demolition mud phuska in roofs any thickness including plastering and leeping ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) in bed blocks for hold fast & similar work etc ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour Cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in roof padding (avg 40mm thick), roof kerbs or mud stops, rounded or chamfered on edge ; Complete all as specified and directed by Engineer-in-Charge.

Material and labour for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) laid on primed surface by forced application over a tack coat of in dustrial bitumen 85/25 at the rate of 1.2 kg per sq.m including cleaning surfaces ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for Cement concrete tiles 20cmx20cmx20mm thick,machine pressed ; set, jointed and pointed in neat cement slurry in floors with grey cement and no pigment, and cut and polished over and including 15mm thick screed bed in CM 1:4 ; Complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete above ground floor and in any position ; Complete all as specified and directed by Engineer-in-Charge.

Supply only integral water proofing compound (for sunken portion only) ; Complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster on brick, concrete or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. Of any description ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for 15mm thick cement plastering in cm 1:6 on brick or concrete surfaces other than fair surface, finished the surfaces even and fair without using extra cement ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for 10mm thick cement plastering in CM 1:3 on ceiling surfaces other than fair surface, finished the surfaces even and fair without using extra cement ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour fpr Rendering 15 mm thick on fair/unfair faces of brick work or concrete surfaces in CM 1:4 and to be finished even and smooth ( without using extra lime or cement) ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour preparation of new plaster surface and applying two coats of Oil bound distemper over a coat of primer over wall care putty on walls ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour preparation of newly plastered surface of wall and applying two coats cement base paint over a coat of primer to match the existing treatment ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour preparation of new plaster surface and applying two coat of white wash on wall ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour preparation of new plaster surface and applying two coat of white wash on ceiling ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for Complete removal and preparation of existing treatmnet of plastered surfaces on walls applying two coats of Oil bound distemper over a coat of primer ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for preparation of existing treatmnet of plastered surfaces on walls applying one coat of Oil bound distemper ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for one coat of white wash on old treated plastered surface on walls of undecorated surfaces ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for one coat of white wash on old treated plastered surface on ceiling surfaces ; Complete all as specified and directed by Engineer-in-Charge.

Taking down chowkats with shutter n.exc 1.50 Sqm each (without taking off shutter for the chowkats ) ; Complete all as specified and directed by Engineer-in-Charge.

Taking down chowkats with shutterexc 1.50sqm but n.exc 4 Sqm (including CB shutters with chowkhat) (without taking off shutter for the chowkats ) ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing pressed steel frames 1.25mm thick for door size of frame 125 x 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate and tarring to inner surface (surface in contact with concrete/brick surface) of chowkats and hinges ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing pressed steel frames 1.25mm thick for door size of frame 105x60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate and tarring to inner surface (surface in contact with concrete/brick surface) of chowkats and hinges ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing second class hardwood (rail & style) 35mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing IInd class hard wood Glazed and skeleton shutters 35mm thick divided into square, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, Section 8 clause 8.24 (a) ; supplied and fitted to chowkats ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing mild steel work Fe 410-W(Gde-E- 250) quality-A Fe in framed work as in door frame, shutter or gates of angle iron or other section with gusset plates,rails,braces etc complete drilled for fixing of steel sheeting or orther covering doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging also fastening ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour 18/19mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to SS butt hinges fixed with angle iron chowhats ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing18 mm thick PVC board as in cupboard shelves, in kitchen cabinet etc ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing aluminium anodised barel tower bolt of extrud sec 150mm long ISI marked ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing extruded aluminium alloy handle fabricated type anodized of size 150 mm long ISI marked ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 300mm long aluminium alloy,anodised ,sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet,cast or extruded section and fixing bolts and sliding bolts of extruded sectionsor cast aluminium alloy ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 300mm, mild steel ordinary rat tail rod pattern springs,including roller and roller plate ; Complete all as specified and directed by Engineer-in-Charge. Note : Repairs required on steel door frame, welding to be carried out or necessary alternative arrangements to be done.

Supply and Fixing Providing and fixing powder coated(Min thickness of powder coating shall be 50 micron) aluminum windows shutter of size min 18mmx50mm for sliding type windows of standard tubular sections of approved make having glazed panels or glazed and gauzed panels of appropriate size running on seperate tracks in the channel conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth,rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. All the panels shall be of appropriate size having overlaps as required and including all required beadings, clips, rollers, rubber gaskets, cleats, etc. complete and powder coating in approved shade and colour. Note:- Each panel shall be measured separetely. Glass pane and wire mesh shall be measured and paid separetely.

Supply and Fixing Anodised aluminium frame (powder coated, minimum thickness of powder coating 50 micron) for doors,windows,ventilators,side hunge one or more rebates including necessary jointing cleats,glazing clips, ruber neoprene packing anodised aluminium snap beading screw Tee etc ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 5.5 mm thick sheet glass ordinary quality in square or rectangular in size n.exc .5 sqm each in aluminium door or window shutter including ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing figured glass pin head type, 3mm thick ordinary quality, in any shape, not exceeding 0.50 sqm in each pane including and glazing with oil putty ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing rotational moulded polytheylene triple layered white water storage tanks of capacity 500 Litres (cylindrical vertical with closed top) hoisted and fixed in position including dismantling of existing water tank and 20mm dia brass float valve with brass rod ; Complete all as specified and directed by Engineer-in-Charge.

Disconnecting existing tanks 500 ltrs cap, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position and cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc and refixing on same place with brass ball valve 20mm ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing rotational moulded polytheylene triple layered white water storage tanks of capacity 1000 Litres( cylindrical vertical with closed top) hoisted and fixed in position including dismantling of existing water tank and 20mm dia brass float valve with brass rod ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs stop value 20mm bore cast copper alloy with butterfly handle screwed down for high pressure, screed on bath ends, fixed with iron pipe etc ; Complete all as specified and directed by Engineer-in-Charge.

Taking up and down GI pipe15mm bore including fittings, connection, including cleaning for refixing in any position ; Complete all as specified and directed by Engineer-in-Charge.

Taking up and down GI pipe 20mm bore including fittings, connection, including cleaning for refixing in any position ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing GI tubing 15mm bore medium grade, fixed to wall/ceiling or floor etc with all fittings incl taking down ISI marked ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing GI tubing 20mm bore medium grade, fixed to wall/ceiling or floor etc with all fittings incl taking down ISI marked ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs bib taps 15mm dia chromium plated fancy type with capstan head screwed down screwed for iron pipe or for brass ferrule and fixed in repairs ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs stop valves(Concealed cock) 15mm bore chromium plated alloy with butterfly handle screwed down for high pressure, screed on bath ends, fixed with iron pipe etc ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs stop valve/angel valves 15mm bore chromium plated alloy with butterfly handle screwed down for high pressure, screed on bath ends, fixed with iron pipe etc ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs CP shower rose 125 mm size with swivel joint fancy type including fixing to steel pipe or union ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs vitreous china squatting pan “Orrisa Pattern” white of size 580x440mm with internal foot rest with `P’ or `S’ trap, integral foot rest including water connection to trap and flushing pipe, flushing cistern etc including lime concrete in lime mortor 1:3 usisng broken bricks 40mm graded coarse aggregate ; Complete all as specified and directed by Engineer-in-Charge. Note:- Flush pipe and flushing cistern to be measured and paid separately.

Supply and Fixing of Vitreous china wash down water closet pan( pedestal pattern), white ; Complete all as specified and directed by Engineer-in-Charge. Note:-Rate of supply for Flushing cistern, flush pipe, seat cover etc have been taken separately.

Supply only Plastic water closet seat,white/ivory,closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device (Toilet Seat Cover) ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs PVC low level flushing cistern 10ltr capacity, with syphonic action PVC float valve, brackets and 32mm bore PVC flush pipe etc ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs PVC connections 15 mm size with PTMT nuts of length 600 mm ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs Vitreous china wash basin(with pedastal),white flat back,size 550x400mm excluding taps but including brackets,32 mm waste pipe and 32mm brass(CP) waste coupling ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs Pillar taps 15mm bore, cast copper alloy but fancy type, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long embedded in the wall ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing towel ring 300mm dia of brass (chromium plated) fixed with and including Chromium plated brass screws and wooden/plastic cleats ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing brass chromium plated towel rail `D’ type 60 cm long fixed to wall ; Complete all as specified and directed by Engineer-in-Charge.

Dismantling of cast iron ,PVC or SGSW drain pipes, jointed in cement mortar and taking out of trenches , if required ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 110mm bore PVC (SWR) ISI marks pipes single socketed in any length with rubber ring joints fixed to wall or floor ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joint fixed to walls or floor ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing PVC (SWR ) bends with access door 75 mm bore any radius ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing PVC (SWR ) bends with access door 110 mm bore any radius ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing PVC (SWR ) vent cowl 110 mm bore ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour PVC (SWR ) floor trap 75 mm plain with grating incl. jointing with solvent cement as per site requirement ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing Stack clamps (110 mm pipe) out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing Stack clamps (75 mm pipe) out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for preparation of new painted wooden surface exc 10cm width or girth and applying two coat of synthetic enamel paint over one coat of primer ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repairs cutrain rod 20mm dia of SS with fixing brackets, stops, rollers etc fixed to wall with screws, PVC plug including SS bracket fixed to wall and with SS knobs ; Complete all as specified and directed by Engineer-in-Charge.

Demolation of brick work built in cement mortar or cement lime mortar as cutting, opening of exsiting wall ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for brick work with sub class "B" bricks (old size) straight or curved on plan exc 6 m mean radius, built in CM 1:6 ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for brick work with sub class "B" bricks (old size) straight or curved on plan exc 6 m mean radius, in half brick thick walls and built in CM 1:4 ; Complete all as specified and directed by Engineer-in-Charge.

Demolition of Stone slabs and tiles of laid, beded and pointed of any mortar in any description or thickness in floors, aprons etc. ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for Granite (of any type) work (table rubbed and polished) 20 mm thick in steps , jambs, pillars, window cills, cooking plateforms and like in cemnet mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick rendering in CM 1:4 ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for Green Marble work 16mm to 18mm thk (table rubbed and polished) in steps, jambs, pillars window cills , cooking platforms , stair case and like with bull nosing in cement mortar ( 1:4) incl pointing in white cement ( 1:2) using marble dust with admixture of pigment to match with marble shade including making grooves for slip guard on steps, edge moulding, making 30mm dia hole in cooking counter slab & green marble top for gas pipe ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs Stainless steel sink including drainage board, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc. overall size 915mm x 460mm with bowl size 410mm x 330mm x 160mm with coupling and necessary fixing arrangment ; Complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete in ground floor & paving n.exc 15cm above ground level ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for 50mm thick cement cocnrete type C-1 (1:3:6) (20mm graded aggregate) as in plinth protection finishing the surface even and fair ; Complete all as specified and directed by Engineer-in-Charge.

Roughning the surface of old concrete floor picking sweeping clean and washing down with water to remove dust/mud etc.and brushing neat cement slurry @ 3kg/Sqm ; Complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour Non skid coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) size 400mmx400mm in floors etc set and jointed in neat cement slurry and pointed in white cement or clolured cement to match including 15 mm thick screed bed in cm 1:6 ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour Non skid coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) size 400mmx400mm in skirting etc set and jointed in neat cement slurry and pointed in white cement or clolured cement to match including 10 mm thick screed bed in cm 1:4 ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for glazed ceramic coloured tiles in vertical surface of size 450x300x6-7mm thick joint free on and incl 10mm thick screed bed in cm(1:4)set and jointed in neat cement slurry and pointed in colored cement mixed with pigment to match the colour of tiles ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for repairsing of RCC projections, chajjas, roofs, facia etc. by necessary preparations i.e. scrapping, cutting, chiseling, dusting and cleaning exposed reinforcement, surfaces of damaged, loose RCC surfaces and applying one coat of cement slurry and filling the surfaces with cement concrete (1 : 2 : 4) using 12.5mm graded crushed stone aggregate and reinforced with 10mm TMT bars with or without facia and finished with cement sand mortar (1:3) using coarse sand in patches area n.exc 5 Sqm each and thickness of RCC member exc 50mm including applying two coats of Finishes to match with the existing surfaces in upto 12m height ; Complete all as specified and directed by Engineer-in-Charge. Note: - Cost of formwork and welded mesh, bldg ht upto 12 mtr, shall be deemed to be included in unit rate quoted by the Contractor.

Demolition of cement concrete (Reinforcment) of any description ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for RCC in 1:2:4 type B-1(using 20 mm graded stone agg) as in chajjas facia, shelves, lintel etc and similar work ; Complete all as specified and directed by Engineer-in-Charge.

Formwork to rough finished surface of concrete flat to soffits of shelve, chajja, fins etc including supports over hangs upto 12m height ; Complete all as specified and directed by Engineer-in-Charge.

Formwork (rough finished) to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 10 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 5cm but n exc 10cm wide ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 10mm dia over TMT bar cut to length bent to shaps including cranking binding spirraly, hooping, hooking end and binding with MS wire (anealed) not less then 0.9 mm dia or securingwith clips ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for TMT bars 6 to 8mm dia and over cut to length bent to shape required including crancking spirally for hooking ends and binding with and including MS wire annealed n.less than 0.9mm dia ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs stainless steel kitchen plate rack size 900 x 750 x 250mm deep made out of 1mm thick sheet including fitting arrangement ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for Vitrified ceramic light shade tiles 8-10mm thick (Square/ rectangular) polished,area of tile exc 0.42 Sqm but n exc 1.00 Sqm each in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of cement mortar(1:6) 15mm thick for laying floor finishes ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for Vitrified ceramic light shade tiles 8-10mm thick (Square/ rectangular) polished,area of tile exc 0.42 Sqm but n exc 1.00 Sqm each in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of cement mortar(1:4) 10mm thick for laying floor finishes ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 5 mm thick PVC sheat as in back side of kitchen cabinet etc ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 18 mm thick PVC sheet shutter one side prelam of any shade as in kitchen cabinet etc ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 40 mm long hinges self closing type hydrulic type ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing Chromium plated Health faucet in repairs with 1.5 metre long chain ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing CP wall mixer with telephonic shower arrangement and telephonic shower suitable for 15mm dia bore pipe ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing glass corner of 30cm radius made of 5.5mm thick sheet galss with CP guard rails fixed to walls with brackets ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing PVC Mirror cabinet with shelves of best quality including fixing arrangements size 600x450mm ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing centre hole mixer cast copper alloy chromium plated with capston head srewed down high pressure with lettered hot or cold with long screwed shanks fly nut screwed for iron pipe 15mm dia ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for preparation of old steel surfaces and applying two coats of synthetic enamel paint over zinc chromate primer including preparation of steel surfaces ; Complete all as specified and directed by Engineer-in-Charge.

Dismantling boarding, any description, fixed in any position with screws (for kitchen cupboard shutter and shelves) ; Complete all as specified and directed by Engineer-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads in wooden/steel window ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for complete removal of existing treament including preparation of surfaces and applying two coats of cement base paint on walls ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing clear glass, 3mm thick ordinary quality, in any shape, not exceeding 0.50 sqm in each pane including and glazing with oil putty ; Complete all as specified and directed by Engineer-in-Charge.

Taking down carefully the existing aluminium point wiring of any size and capacity and type by disconnecting from the either terminals complete including fittings and fixtures such as switches, sockets,ceiling rose, regulators and light fittings any type etc by unscrewing and taken away from site ; Complete all as specified and directed by Engineer-in-Charge. Note :cost of unserviceable materials will be charged from the contractor against schedule of credit.

Material and Labour Wiring complete with 1.5 sqmm single core PVC insulated unsheathed cable 1100 volts grade, multistranded with copper conductors conforming to IS specifications, drawn through and including conceled conduit concealed/ fixed on wall / ceiling with suitable clamps, screws, etc or concealed in wall including terminal boxes fabricated with 1.6 mm MS sheet concealed in walls covered with plastic laminated sheet top cover 3 mm thick fixed with cadmium plated iron screws for housing the switches, switch sockets outlets, fan regulators, etc, including provn of 1.5 sqmm PVC insulated unsheathed cable with multistranded copper conductor as earth continuity conductor and connecting to common earth dolly ; Complete all as specified and directed by Engineer-in-Charge. :- (a) One light point/Bell/Fan point controlled by one switch.

Material and Labour Wiring complete with 1.5 sqmm single core PVC insulated unsheathed cable 1100 volts grade, multistranded with copper conductors conforming to IS specifications, drawn through and including conceled conduit concealed/ fixed on wall / ceiling with suitable clamps, screws, etc or concealed in wall including terminal boxes fabricated with 1.6 mm MS sheet concealed in walls covered with plastic laminated sheet top cover 3 mm thick fixed with cadmium plated iron screws for housing the switches, switch sockets outlets, fan regulators, etc, including provn of 1.5 sqmm PVC insulated unsheathed cable with multistranded copper conductor as earth continuity conductor and connecting to common earth dolly ; Complete all as specified and directed by Engineer-in-Charge. :- (a) One 3 pin 5 amps switch socket on independent board.

Material and Labour Wiring complete with 1.5 sqmm single core PVC insulated unsheathed cable 1100 volts grade, multistranded with copper conductors conforming to IS specifications, drawn through and including conceled conduit concealed/ fixed on wall / ceiling with suitable clamps, screws, etc or concealed in wall including terminal boxes fabricated with 1.6 mm MS sheet concealed in walls covered with plastic laminated sheet top cover 3 mm thick fixed with cadmium plated iron screws for housing the switches, switch sockets outlets, fan regulators, etc, including provn of 1.5 sqmm PVC insulated unsheathed cable with multistranded copper conductor as earth continuity conductor and connecting to common earth dolly ; Complete all as specified and directed by Engineer-in-Charge. :- (a) One 3 pin 5 amps switch socket on same board.

All as per item herein before but with cable 2.5 sqmm (nominal area) multistranded copper wire unsheathed for one 3 pin socket outlet 15 amps on independent board including continous earth wirte PVC insulated 1.5 sqmm copper multistranded conductor connecting to common earth and earth dolly ; Complete all as specified and directed by Engineer-in-Charge. :- (a) The wiring shall be done in proper colour coding using red,yellow and blue for phase,black for neutral and green for earth leads.

Supply and fix switch piano one way 5 A, SP, 230 Volts ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fix Socket outlet 2 in 1, 3 pin 5 Amps Flush type ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fix Switch outlet 2 in 1, 3 pin15 Amps Flush type ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fix stepped type electronic fan regulator flush type ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing ceiling rose surface bakelite 3 terminals 65x32mm ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing Lamp holder, PVC/Polycarbonate type with cord grip cap suitable for pendant/batten fittings ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fix wall/ceing mounting LED 18 Watt PC Diffuser tube light fitting complet with all aceesories 1x18W LED suitable for domestic application 240Volts 50HZ including one tube rode and internally pre-wired with 1.5 sqmm twin twisted flexible copper conductor and ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing energy saving new generation 10 watt LED, 6000k bulk head luminaire with opal diffuser light fitting complete with all acessories and connection ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for sub main wiring with PVC insulated, 1100 volts grade single core multistranded copper conductor cable conforming to IS specifications, 3 runs of 4 sqmm single core multistranded copper conductor PVC insulated cables as neutral continuity conductor drawn through and including one run of 25 mm dia rigid PVC conduit and conduit accessories fixed on wall/ceiling etc., or concealed in wall and connecting to common earth dolly including taking down all sub main wiring ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs MCB single pole, 240 volts, 6 to 32 Ampere, rupturing capacity 10 KA, ‘B’ curve type ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing of socket outlet two-in-one, 3 pin each suitable for 5 and 15 Amperes flush type, 250 volts AC ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement of security light fitting LED 36 Watt aluminum pressure dia cast housing with touched glass cover IP-66 protection Including suitable size and accessories complete mounted including connection with 3 core PVC insulated overall sheathed flexible cable with muyltistranded copper conductor of size not less than 1.0 sq mm from celing rose to fitting terminal including taking down old CFL security light fitting ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing GI bracket light grade GI Pipe 1.2 mtr Length for fixing of street light fitting 36/40 Watt including connection ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing MCCB Incomer distribution board double door vertical type made out of CRCA MS sheet surface with insulated material like polyester or with epoxy powder coating surface mounting TPN 8 way, 415 volts with copper bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCCB and IP 43 - IK 09 protection with and incl 100 amp 36 kA 4 pole MCCB with thermal - magnetic setting and Icu = Ics = 100% ; Complete all as specified and directed by Engineer-in-Charge.(Note : The cost of removing old wooden box and making good of surface as original by brick work, plastering, whitewash/colour/distemper etc is included in quated rate)

Supply and Fixing exhaust t fan 450 mm sweep including cutting of wall /window/lowers and fixing arrangement complete ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing exhaust t fan 300 mm sweep including cutting of wall /window/lowers and fixing arrangement ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for earthing complete with galvanised earth plate electrode 600 X 600 X 6 mm thick buried directly in ground (earth pit not less than 2.25 m below ground level) with top edge of earth plate not less than 1.5 m below normal ground level, connected to galvanised earth lead wire 4 mm dia by means of nuts, bolts, check nuts & washers of galvanised iron or steel all as shown on electrical plate No. 3 of MES schedule 2009, Part – I (Specifications) and connected to main switch board / main DB’s / earthing test point including all necessary excavation and earth work in any type of soil, adequate quantity of charcoal dust & common salt all around the earth plate minimum 150 mm in all directions with & including watering pipe 20 mm dia GI medium grade, GI funnel made out of 0.63 mm thick GI sheet, wire gauge, 50 mm thick RCC cover in PCC 1:2:4, type B-1, duly reinforced with 6 mm dia mild steel round bars @ 150 mm both ways center to center with suitable lifting handle to cover, earth pit of PCC 1:3:6 type C-1, GI protection pipe light grade 15 mm bore up to 7.5 m length from earth electrode & engraving of earth marking on nearby building with CM 1:4 plate size 200 X 150 X 15 mm & painting of earth result etc. including testing on ; Complete all as specified and directed by Engineer-in-Charge. Note : - (i) Earth lead and protection pipe beyond 7.5 m shall be measured and Paid separately. (ii) On testing after completion of job, if desired earth resistance is not obtained, the earthing shall be redone by the contractor without any extra cost to Govt.

AC/SRW(BLDG)-03/2023-24 Taking down shutter and removing from site of any description size but exc 1 sqm and n.exc 2 sqm ; Complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frame without taking of shutter and removing from site exc 1.5sqm but not exceeding 4 sqm each ; Complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frame (w/o taking off shutters) and removing from site n.exc 1.5sqm each ; Complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster from wall's/ceiling including raking out joints hacking for key scrubbing down with water and dispose off debries upto distance n exc 500 metre where directed ; Complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (un-reinforced)in ground floor and paving n. exc 15 cm thick below or above ground level & dispose off debris upto a distance n. exc. 50 mtrs where directed ; Complete all as specified and directed by Engineer-in-Charge.

Demolation of RCC in any position not otherwise specifically provided ; Complete all as specified and directed by Engineer-in-Charge.

Material and labour PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate as in hold fast block, roof kerbs or mud stop, coping, rounded or chamfered on edges and like including weathering, slightly rounded or chamfered angles and throating etc incuding necessary form work ; Complete all as specified and directed by Engineer-in-Charge.

Demolition of brick work built in cement mortar, seperation, cleaning and stacking of serviceable bricks for reuse and removal of debris,rubbish to a distance exc 400 m but not exc 500m ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for brick work with sub Class 'B' old size bricks, straight or curved on plan exceeding 6 Metre mean radius, built in cement mortar 1:6 ; Complete all as specified and directed by Engineer-in-Charge.

Material and labour for 15mm thick cement plaster in CM (1:6) on fair faces of brick or concrete surfaces and finishing the surface even and smooth (without using extra cement) etc. ; Complete all as specified and directed by Engineer-in-Charge.

Material and labour for 10 mm thick cement plaster in CM (1:3) on concrete surfaces of ceiling and finishing the surface even and smooth (without using extra cement) etc ; Complete all as specified and directed by Engineer-in-Charge.

Material and labour for 15mm thick cement plaster in CM 1:4 on fair faces of brick work and finishing the surface even and smooth (without using extra cement) etc. ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour preparation of new plaster surface and applying two coats of white wash on wall ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for preparation of old decorated plastered surfaces, filling nail holes or patches with wall care putty to make surface smooth and applying two coats of oil bound distemper on walls ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for preparation of new plastered surfaces and applying three coats of white wash on ceiling ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for preparation of new plastered surfaces and applying two coats of cement base paint on wall ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for complete removal of existing treament including preparation of surfaces and applying two coats of cement base paint on walls ; Complete all as specified and directed by Engineer-in-Charge.

Material and labour for complete removal of all existing treatment and applying two coats of oil bound distemper on the wall surfaces ; Complete all as specified and directed by Engineer-in-Charge.

Material and labour for applying average 1 mm thick wall putty after complete removal of existing treatment on wall, ceiling, on old decorated surfaces or newly plastered surfaces ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing for Factory made single extructed WPC but frame size 50x 100 mm (wood polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat of size 45 x 70mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), Calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum,screw withdrawel strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2,modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof,water/moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Chaege

Supply and Fixing for Factory made single extructed WPC (wood polymer Composite) solid Plain flush door shutters of 30 mm thick comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), Calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minumum dencity of 650 kg/ cum and screw withdrawa strenth of 1800 N (Face )&900 N (Edge), minimum compressive strength of 50 N/mm2,modules of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof,water/moisture proof and fire retardant and fixed with steelness steel butt hinges of requred size with necessary full body threank SS screw ; Complete all as specified and directed by Engineer-in-Charge. ( steelness srew and butt hinges and necessary SS Screw shall be paid separatly)

Supply and Fixing Steel window 1.25mm thick box type ERW hollow P section of each frame size 60mmx25mm double rebated comprises of glazed & gaused Skelton shutter ERW section 50mmx20mm & 1mm thick with one openable leaf consisting of two number sash bars of T-Section 20mmx3mm complete welded to frame with one vertical mullion of ERW box type T-Section of size 60mmx25mm and 1.25mm thick with following fittings welded to the frame shutter :- Ref Drg No CE JZ/TD-06/07 i) Hold fast 150mm long mild steel flat iron 12x3 mm made to shape- 04 Nos per window ii) Handle of Z section 20mmx25mm, 100mm long – 01 No per leaf. iii) MS tower bolt 150mm long 2 No per leaf. iv) Z section 20mmx25mm, 100mm long stopper – 01 Nos per leaf. (v) Cleat 55 mm long of solid square 15x20x.63mm square - 01 Nos per leaf vi) pintol hinges 12 x 75 mm - 2 Nos each leaf vii) 10mm square Guard bar @ 10 cm c/c. (viii) 25 x 3 mm flat iron for joint of both frame wiremesh & Glazed welded inner side and outer side of frame (ix) (x) 0.36mm nominal dia of stainless steel wire mesh and average width of aperture of 1.40mm fixed in glazed / gazed skelton shutter of window (xi) 3mm thick sheet glass, ordinary quality and with oil putty in Square n. exc 0.5 sqm in each pane fixed in glaxed / gazed skelton shutter of window. (xii) Fabrication and fixing arrangements as per Drg No CE JZ/TD-06-07 including taking down, cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 /cement plaster 1:4 as require and make finish good to the existing surface ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs mild steel box type ventilator fixed type with glazing bar with mesh & glass as per drg No. CEJZ/TD-06/07 dt 07.06.07 primer coated ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 30 mm thick flush shutter, soild core construction with block board core and plywood face panels commercial type on both side ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 35 mm thick 2nd class hard wood glazed and skeleton shutter’s open rebated prepare to receive glass gauge etc edges of framing plain chamfered or rounded fitted with Cut and mitered bead’s for securing glass gauge etc size of mamber of shutters as per SSR Part-I Section-8 clause 8.2 (a) ; Complete all as specified and directed by Engineer-in-Charge.

Hacking out old broken glass any thickness, size, quality or description from steel frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 3mm thick ordinary sheet glass and glazing with oil putty or fixed on steel frame, in squares not exc 0.50 Sqm in each panes ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing stainless steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staples ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repairs stainless steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staples ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 300 mm size, aluminium alloy,anodized sliding door bolt, clip type, and fixing clips of sheets or extruded section and fixing of bolts and sliding bolts of extruded section fixed with stainless steel screw ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing butt hinges 100mm size medium weight cold rolled mild steel fixed with stainless steel screw ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repairs 150 mm size aluminium anodized barrel tower bolt of extruded section fixed with stainless steel screw ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repairs 300mm mild steel ordinary rat tail rod pattern spring including roller plate including fixing with nailsd/ bolts or welded ; Complete all as specified and directed by Engineer-in-Charge..

Supply and fixing in repairs 125 mm size extruded aluminium anodized handle cast type fixed with stainless steel screw ; Complete all as specified and directed by Engineer-in-Charge.

Material & Labour for Preparation of new wooden surface over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer ; Complete all as specified and directed by Engineer-in-Charge.

Material and labour for preparation of old painted wooden surfaces of any description, over 10 centimetre width or girth and applying one coat of synthetic enamel paint ; Complete all as specified and directed by Engineer-in-Charge.

Material and labour for applying two coat of synthetic enamel paint over a coat of red oxide, zinc chrome primer on steel surfaces exceeding 10 cm width or girth including preparation of new surfaces ; Complete all as specified and directed by Engineer-in-Charge.

Material and labour for preparation of old painted steel surfaces of any description, over 10 centimetre width or girth and applying one coat of synthetic enamel paint ; Complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel water tubing and connections including cleaning serviceable pipe for refixing and removal of unserviceable pipe, bore of pipe 15mm complete all as specified. Note :- The quoted rates shall be include for necessary excavation and earth work, cutting/ chasing in wall/ floor and making good in CM1:3 ; Complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel water tubing and connections including cleaning serviceable pipe for refixing and removal of unserviceable pipe, bore of pipe 20mm complete all as specified. Note :- The quoted rates shall be include for necessary excavation and earth work, cutting/ chasing in wall/ floor and making good in CM1:3 ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing galvanized iron steel tubing medium grade 15mm bore with all fittings and fixed Complete all as specified to walls, ceiling or laid in floor ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing galvanized iron steel tubing medium grade 20 mm bore with all fittings and fixed Complete all as specified to walls, ceiling or laid in floor ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repairs PVC connection 450mm long of 15mm size with PTMT nuts on both sides ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs bib taps 15mm dia chromium plated fancy type with capstan head screwed down screwed for iron pipe or for brass ferrule and fixed in repairs ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs stop valves(Concealed cock) 15mm bore chromium plated alloy with butterfly handle screwed down for high pressure, screed on bath ends, fixed with iron pipe etc ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs angel valves 15mm bore chromium plated alloy with butterfly handle screwed down for high pressure, screed on bath ends, fixed with iron pipe etc ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs angel valves 15mm bore chromium plated alloy with butterfly handle screwed down for high pressure, screed on bath ends, fixed with iron pipe etc ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing vitreous china squatting pan ( Orissa Pattern) size 580 x 440 mm (white), with PVC P or S trap, integral foot rest including water connection to trap and flushing pipe, flushing cistern etc complete and bedding in PCC 1:7:12 type F-2 including taking down/dismantling old unserviceable WC ; Complete all as specified and directed by Engineer-in-Charge. Note :- Flush pipe and flushing cistern to be measured and paid separately.

Material and Labour cement concrete (1:2:4) type B-0 using 12.5mm graded stone aggregate as in sides of sunken slab benching etc including necessary form work ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour rendering 15mm thick cement plaster as in sunken portion in cement mortar 1:3 using water proofing compound, finished fair and even without using extra cement ; Complete all as specified and directed by Engineer-in-Charge. (WPC measured saperatly)

Supply and Fixing 40mm bore steel water tubing grade galvanised inserted at the end of lateral slope projecting atleast 25cm beyond the outermost part of the building below the drain pipe up to two storey construction as spout for sunken, and all joints should be sealed properly by epoxy sealent ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour Water proofing treatment to sunken floor including wall comprising with the following course of treatment/ specification from bottom to top. (a) Applying bituminous primer @ 0.40 ltrs per sqm over plastered surface of floor for treating the sunken floor all as specified & as directed by Engr-in-Charge. (b) Apply a coat of hot bitumen 85/25 penetration grade bitumen @ 1.20 kgs/Sqm. (c) One layer of 3mm thick APP film based poly meric membrance minimum weighing 3Kg per Sqm reinforced with polyester non wove fabric (weight not less than 150 gms/sqm) land on primed surface by forced application over entire area, ; Complete all as specified and directed by Engineer-in-Charge. Note:-(i) After plastering testing tobe carried out by ponding (For 48 Hrs) and any leakage/Seepage observed shall be rectified before water proofing treatment. (ii) Laying of APP membrane shall be done as per manufracturers instructions . (iii) Joints tobe touched hot and Minimum width of overlaps not less than 150mm.

Material and Labour Plain cement concrete (1:5:10) type E-2 using 40mm graded stone aggregate as in sunken filling as mass concrete or in sub base of floors ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing white PVC valve less syphonic action type low level flushing cistern of 10 ltrs capacity with inlet ball valve, float valve, push button type handle including pipe 32mm dia of PVC(Heavy duty) flush pipe including brackets and taking down/dismantling old unserviceable cistern ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repairs viterous chinaware wash hand basin ovel size light colour/white of size 550x 400cm flat back or angle stay, brass chromium plated waste coupling, chain, plug, porcelain rubber stopper, brackets,32mm bore PVC waste pipe of appropriate length ilcluding taking out of old WHB & making necessary connections ; Complete all as specified and directed by Engineer-in-Charge.

Dismantling water tanks and Supply & Fixing rotational moulded polythene water storage tanks of 1000 litre capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-1 including Ball valves high pressure PTMT with epoxy coated Aluminium rod & High density plastic ball screwed for iron pipe and fixed to GI pipe of 20mm bore ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing sheet glass shelf assembly 60 cm oval shape consisting 5.5 mm thk 8mm thk glass with brass bracket including stainless steel railing, fixed to wall as ; Complete all as specified and directed by Engineer-in-Charge.

Roughening of surface of old concrete floor, sweeping, clean and washing with water to remove dust ; Complete all as specified and directed by Engineer-in-Charge.

Dismantaling floor hearth or wall tiling incl cement mortar bedding (but not backing ) removing serviceable tiles to store and rubbish off the premises ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for glazed ceramic coloured tiles in vertical surface of size 350x250x7mm/ 450x350x7mmmm thick joint free on and incl 10mm thick screed bed in cm(1:4)set and jointed in neat cement slurry and pointed in colored cement mixed with pigment to match the colour of tiles ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing Coloured/printed non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0. 11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or Coloured cement to match over 15 mm thick screed bed or bedding layers in CM 1:6. ; Complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete in ground floors and paving not exceeding 15 cm thickness ( below or above ground level) and disposing the rubbish to a distance exceeding 50 Mtr but not exceeding 100 Mtr away to low lying areas ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour forMachine cut kota stone slab flooring 16-18mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete to achieve mirror finish laid over & including 20 mm thic screed bed in CM 1:6 ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour forMachine cut kota stone slab flooring 16-18mm thick in riser of steps skirting dado and pillar laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete to achieve mirror finish laid over & including 10 mm thic screed bed in CM 1:6 ; Complete all as specified and directed by Engineer-in-Charge.

Dismantling of PVC/CI pipe of 75/100mm dia fixed with cement joint ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing PVC (SWR) pipes 110mm dia single socketed in any length with rubber ring joints fixed to walls ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing PVC (SWR) pipes 110mm dia bend any radius ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour PVC (SWR) gully trap 125/110mm setting and jointing with solvent cement ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 110mm bore PVC (SWR) branch piece , single, equal fitted with oval access doors ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for PCC type D 2 (1:4:8) 40mm graded aggregate ; Complete all as specified and directed by Engineer-in-Charge.

Material and labour for repairsing of RCC projection, chajjas, facia,bands, shelves, beams, RCC railing, balcony and similar works by dismantling of loose/ disintegrated portion RCC at any height and in any sitution floor (including provn of support, formwork and welding of reinforcement if required with wire mesh of eight 1.5 kg/ sqm and dubbing/ filling with PCC (1:2:4), type B-0, using 12.5 mm graded aggregate,15 to 25 mm thick after applying cement slurry @ 3 kg/sqm, finished even and smooth to desired shape and applying two coats of wheater proof emulsion paint to match with existing surfaces ; Complete all as specified and directed by Engineer-in-Charge.

Material and labour udaipur green marble 16-18mm thick confirming to sample kept in GE 's office ( table rubbed and polished inslab, stair case, step and like jointed with grey cement slurry mixed with pigment to match with shade of marble over and including 15mm thick cement screed bed in CM (1:6) ; Complete all as specified and directed by Engineer-in-Charge.

Material and labour steel framed work as in chowkhat, doors of angle or other section complete drilled for fixing sheeting with all fitting and fixture ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs CI floor trap( long nose) 75mm bore with grating including Jointing to waste pipe fixed in PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) ; Complete all as specified and directed by Engineer-in-Charge.

Taking down carefully the existing aluminium point wiring of any size and capacity and type by disconnecting from the either terminals complete including fittings and fixtures such as switches, sockets,ceiling rose, regulators and light fittings any type etc by unscrewing and taken away from site ; Complete all as specified and directed by Engineer-in-Charge.. Note :cost of unserviceable materials will be charged from the contractor against schedule of credit.

Material and Labour Wiring complete with 1.5 sqmm single core PVC insulated unsheathed cable 1100 volts grade, multistranded with copper conductors conforming to IS specifications, drawn through and including conceled conduit concealed/ fixed on wall / ceiling with suitable clamps, screws, etc or concealed in wall including terminal boxes fabricated with 1.6 mm MS sheet concealed in walls covered with plastic laminated sheet top cover 3 mm thick fixed with cadmium plated iron screws for housing the switches, switch sockets outlets, fan regulators, etc, including provn of 1.5 sqmm PVC insulated unsheathed cable with multistranded copper conductor as earth continuity conductor and connecting to common earth dolly ; Complete all as specified and directed by Engineer-in-Charge. :- (a) One light point/Bell/Fan point controlled by one switch.

Material and Labour Wiring complete with 1.5 sqmm single core PVC insulated unsheathed cable 1100 volts grade, multistranded with copper conductors conforming to IS specifications, drawn through and including conceled conduit concealed/ fixed on wall / ceiling with suitable clamps, screws, etc or concealed in wall including terminal boxes fabricated with 1.6 mm MS sheet concealed in walls covered with plastic laminated sheet top cover 3 mm thick fixed with cadmium plated iron screws for housing the switches, switch sockets outlets, fan regulators, etc, including provn of 1.5 sqmm PVC insulated unsheathed cable with multistranded copper conductor as earth continuity conductor and connecting to common earth dolly all as specified and as directed :- (a) One 3 pin 5 amps switch socket on independent board.

Material and Labour Wiring complete with 1.5 sqmm single core PVC insulated unsheathed cable 1100 volts grade, multistranded with copper conductors conforming to IS specifications, drawn through and including conceled conduit concealed/ fixed on wall / ceiling with suitable clamps, screws, etc or concealed in wall including terminal boxes fabricated with 1.6 mm MS sheet concealed in walls covered with plastic laminated sheet top cover 3 mm thick fixed with cadmium plated iron screws for housing the switches, switch sockets outlets, fan regulators, etc, including provn of 1.5 sqmm PVC insulated unsheathed cable with multistranded copper conductor as earth continuity conductor and connecting to common earth dolly ; Complete all as specified and directed by Engineer-in-Charge. :- (a) One 3 pin 5 amps switch socket on same board.

All as per herein before but with cable 2.5 sqmm (nominal area) multistranded copper wire unsheathed for one 3 pin socket outlet 15 amps on independent board including continous earth wirte PVC insulated 1.5 sqmm copper multistranded conductor connecting to common earth and earth dolly ; Complete all as specified and directed by Engineer-in-Charge. Note (a) The wiring shall be done in proper colour coding using red,yellow and blue for phase,black for neutral and green for earth leads.

Supply and fix switch piano one way 5 A, SP, 230 Volts ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fix Socket outlet 2 in 1, 3 pin 5 Amps Flush type ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fix Switch outlet 2 in 1, 3 pin15 Amps Flush type ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing ceiling rose surface bakelite 3 terminals 65x32mm ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing Lamp holder, PVC/Polycarbonate type with cord grip cap suitable for pendant/batten fittings ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fix wall/ceing mounting LED 18 Watt PC Diffuser tube light fitting complet with all aceesories 1x18W LED suitable for domestic application 240Volts 50HZ including one tube rode and internally pre-wired with 1.5 sqmm twin twisted flexible copper conductor and ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for sub main wiring with 1100 volt grade two single core PVC insulated and unsheathed cable with stranded copper conductor 4 sqmm drawn into and including electrical grade PVC conduit not less than 25 mm dia with IS 9537 (Part-III) 1983 mark, or relevant ISI mark with all accessories fixed concealed including chase cutting in brick/ stone masonry for fixing conduit and making good the disturb surfaces of wall as per existing including 2.5 sqmm multi - stranded copper conductor as earth wire in green colour ; Complete all as specified and directed by Engineer-in-Charge.

Supply and fixing of socket outlet two-in-one, 3 pin each suitable for 5 and 15 Amperes flush type, 250 volts AC ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing exhaust t fan 250 mm sweep metal body heavy duty including cutting of wall /window/lowers and fixing arrangement ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for laying of LT cable of 1100 volt XLPE insulated and PVC sheathed of size 25 sqmm 4 core with cable gland including taking down old unserviceble cable complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches in soft/loose soil not exceeding 1.5 meters wide and not exceeding 1.5 meter depth for foundation for LT cables ; Complete all as specified and directed by Engineer-in-Charge.

Returning filling in trenches including spreading leveling watering and well ramming in layers each not exceeding 25 cm in soft/loose soil ; Complete all as specified and directed by Engineer-in-Charge.

Removing surplus spoil to a distance not exceeding 50 meter and depositing where directed at a level not exceeding 1.5 meters above the starting point, ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for Sand cushioning to UG cable 40cm wide 15cm and 10cm thick above and below the cable in trenches/ducts complete all as specified and directed by Engineer-in-Charge.

Supply and laying burnt brick sub class 'B' modular size, for cable protection laid length wise perpendicular to the axis of cable ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection surface mounting SPN 4 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc ; Complete all as specified and directed by Engineer-in-Charge... (Note : cost of removing old wooden box and making good of surface as original by brick work, plastering, whitewash/colour/distemper etc is included in quated rate)

Supply and Fixing in repairs MCB double pole, 240 volts, 32 Ampere, rupturing capacity 10 KA, ‘B’ curve type ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs MCB single pole, 240 volts, 6 to 32 Ampere, rupturing capacity 10 KA, ‘B’ curve type ; Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing MCCB Incomer distribution board double door vertical type made out of CRCA MS sheet surface with insulated material like polyester or with epoxy powder coating surface mounting TPN 4 way, 415 volts with copper bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCCB and IP 43 - IK 09 protection with and incl 100 amp 36 kA 4 pole MCCB with thermal - magnetic setting and Icu = Ics = 100% (Make of MCCB : Legrand Lexic DPX /Schinder Elect Compact CVS/L&T DU 100) ; Complete all as specified and directed by Engineer-in-Charge. Make : Legrand Lexic (Cat Part 607790) / Hager (Cat Part No HVD04MGN) / Schneider Merlin Gerin Multi-9 (Cat Part No MGNV10CDD12). (Note : The cost of removing old wooden box and making good of surface as original by brick work, plastering, whitewash/colour/distemper etc is included in quated rate)

AC/REV/03/2023-24 Material and Labour for Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting outsoft/loose soil ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for broken Stone Hardcore of gauge n exc. 63 mm, deposited , spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour 75mm thick Cement concrete type D2, 1:4:8 using 40mm graded agregate as in sub base of floor ; Complete all as specified and directed by Engineer-in-Charge.

Supply and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath,parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratorymethod using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; ; Complete all as specified and directed by Engineer-in-Charge.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft/loose soil ; Complete all as specified and directed by Engineer-in-Charge.

Removing excavated material n.exc 50 m and depositing where directed ; Complete all as specified and directed by Engineer-in-Charge.

Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for Providing, cement concrete type B1 1:2:4 (20mm graded stone aggregate)in copings, rounded or chamfered on edges ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces ; Complete all as specified and directed by Engineer-in-Charge.

Material and Labour apply three coats of white wash including preparation of new plaster surfaces ; Complete all as specified and directed by Engineer-in-Charge.

amardeep traders

ESS KAY BUILDER

m/s. gopal krishan

RAJ KAMAL BUILDERS