PROVN OF REGT STORE,SMALL-Q STORE, BRICK WK,PLASTERING, SEWAGE LINE,SANITARY FITTING,ROOF SHEET, JOINARY FOR TOILET BLDG ALONGWITH SPL REPAIR TO OTM ACCN (BLDG P-1081) OF UNITS IN THE AOR OF AGE BR-III UNDER GE 864 EWS

Amount

S&F for galvanized corrugated 0.63mm thick mild steel sheeting with two corrugation side lap, fixed with L-type or J-type or cranked hook bolts in roofs, walls etc including dismantling of old corrugated steel sheeting, any gauge, thickness all as specified and directed.

S&F for plain, galvanised, 0.63mm thick mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 including dismantling of old plain sheeting ,any gauge, thickness complete all as specified and directed.

S&F for mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel of flat sections) including distance pieces, cleats etc of Fe 410.00 (Gde E.250 quality 'A') and fixing including dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

M&L for pre polished machine cut Kota stone slab (Mirror finish) flooring 18-20 mm thick over and including cement screed base 15 mm thick in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including roughening/complete scarification of surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified.

M&L for pre polished machine cut Kota stone slab (Mirror finish) 18-20 mm thick in riser of steps, skirting, dado and pillar laid over and including 10 mm cement plaster in CM 1:4 including roughening/complete scarification of surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc.complete all as specified.

M&L for pre polished green marble work 18 to 20mm thick in steps, jambs, pillars, window cills, cooking platforms, cupboards and like in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match including roughening/complete scarification of surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified.

M&L for autoclaved aerated block (AAC) masonry and setting in cement mortar 1:4. The rate includes providing and placing in position 02 Nos 8 mm dia MS bars at every third course including demolition of brick/AAC masonry in any position any thickness complete all as specified and directed.

M&L for stone walling of random rubble, brought up to courses built in CM 1:6 including demolition of brick/AAC masonry in any position any thickness complete all as specified and directed.

M&L for rendering 10mm thick on fair faces of stone work or surface other than fair face of brick work in CM 1:4, complete all as specified.

M&L for rendering 10mm thick on fair faces of brick work or concrete surfaces in CM 1:6 , finished even and smooth without using extra cement all as specified and directed.

M&L for rendering plaster 10mm thick on fair faces of brick work or concrete surfaces in CM 1:6 including taking down old cement plaster from brick/stone work complete all as specified.

M&L for preparation of newly plastered wall surface with wall care putty and applying two coats oil bound distemper, smooth finish complete all as specified and directed.

M&L for preparation of old wall surface and applying two coats oil bound distemper smooth finish including application of wall putty wherever reqd to make up for undulations/cracks etc complete as specified.

M&L for rendering plaster 10mm thick (1st coat) in CM 1:6 and 2nd coat 5 mm thick in CM 1:4 including cost of water proofing compound (as per manufacturer's instrs) on other than fair faces of brick work or concrete surfaces including taking down old cement plaster from brick/stone work complete all as specified. Note : WPC shall be measured and paid separately.

M&L for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces, all as specified and directed.

M&L for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces including preparation/scarification, all as specified and directed.

Taking down chowkhats/frames with shutters (without taking off shutters from the frames) n exc 1.5 Sqm each , all as specified and directed

S&F aluminium powder coated ventilators made of the following specifications :- (a) Aluminium frame powder coated stiles, bottom, top and middle rail of hollow section 50 mm x 25 mm x 1.80 mm thick. (b) Lower portion of ventilator shall be fixed with 3 mm thick pin headed glass fixed with suitable aluminium beading clips and EPDM beading (rubber). (c) Upper portion shall be fixed with aluminium powder coated louver guides fixed with 3 mm thick pinheaded glass with suitable EPDM beading including suitable handle and clips. (d) Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with suitable frame in upper panel. (e) Repair to the jamb, cills and all sides around the window is including in unit rate. The repair finishes to match the existing surfaces like tiles, plastering etc., all as specified and directed. Note:- Net external size of ventilator shall be measured.

S&F aluminium powder coated partitions made of the following specifications :- (a) Aluminium frame powder coated (Vertical and horizontal members) @ not exceeding 1.20 m distance both ways of hollow section 100 mm x 44 mm x 1.60 mm thick. (b) Lower portion of partition shall be fixed with 12 mm thick particle board fixed with suitable aluminium beading clips and EPDM beading (rubber) and all other accessories. (c) Upper portion of partition shall be fixed with 5 mm thick glass (as per user requirement) fixed with suitable aluminium beading clips and EPDM beading (rubber) and all other accessories. (d) Dismantling of old unserviceable partitions of any description and any thickness (AC sheets, wooden particle boards with wooden frame etc ). (e) Repair to the jamb, cills and all sides around the partition is included in unit rate. The repair finishes to match the existing surfaces like tiles, plastering, OBD etc., all as specified and directed. Note:- Net external size of partition shall be measured.

Taking down shutters (steel windows) of any description n.exc 1 sqm each (including removing and refixing glass) and refixing in same opening after removing 02 Nos projected type hinges and replacing them with box type hinges by cutting/welding, etc, everything required as per site requirement all as specified and directed.

S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded, all as specified and directed.

S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded, all as specified and directed.

S&F framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sqm in each pane complete all as specified.

S&F 3 mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane including hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads all as specified.

S&F in repair galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples all as specified.

M&L for two coats of synthetic enamel paint on steel surfaces of any description, over 10cm in width or girth, not other wise described, over one coat of primer with red oxide or zinc chromate on steel surface including preparation of new surface complete all as specified and directed.

M&L for painting of old steel surfaces of any description, over 10cm in width or girth, not otherwise described with a coat of red oxide primer and two coats of synthetic enamel paint (G+2 roofs) including preparation by complete of existing treatment complete all as specified.

M&L for a one coat of synthetic enamel paint on old painted wooden/steel surfaces plain or moulded, n exc 10cm width or girth when unconnected with other painting or when painted in a different tint including preparation, all as specified and directed

Taking down chowkhats/frames with shutters (without taking off shutters from the frames) exc 1.5 Sqm but n exc 4 Sqm each, all as specified and directed

S&F 2nd class hardwood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed, all as specified and directed

S&F factory made 35 mm thick 2nd class hardwood Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated including one shop coat of pink primer all as specified and directed.

S&F factory made 35 mm thick 2nd class hardwood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.20 (a) supplied and fitted to chowkhats including one shop coat of pink primer as specified and directed.

S&F galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples all as specified.

Taking down shutters of any description exc 1.0 Sqm but n.exc 2 Sqm each, all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube, supplying & fixing in opening as per specification & drawing, all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing, all as specified and directed.

S&F 18/19 mm thick block board, grade 2 quality, interior grade, commercial type, fixed with screws to timber frame/steel frame work including dismantling old ceiling/boarding boards of any description complete all as specified.

S&F 100 mm long stainless steel butt hinges, medium weight, and fixed complete all as specified.

S&F 75 mm long stainless steel butt hinges, medium weight, and fixed complete all as specified.

S&F 150 mm long aluminium handles cast type all as specified and directed.

S&F 100 mm long aluminium handles cast type all as specified and directed

S&F aluminium anodised barrel tower bolt of extruded section 150 mm long all as specified and directed.

S&F aluminium anodised barrel tower bolt of extruded section 100 mm long all as specified and directed.

S&F 300 mm long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, all as specified and directed.

S&F 18/19 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber/steel frame work including dismantling old ceiling/boarding boards of any description complete all as specified.

S&F in repair 2nd class hardwood weather boarding, clean sawn, plain, 20mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm laps, all as specified and directed

M&L for preparation of new wood and wood based surfaces of any description not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for glazed ceramic coloured tiles in vertical surface 350x 250 / 450X 350 and 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises all as specified.

M&L for non - skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises , all as specified and directed

M&L for light shade vitrified ceramic tiles 9-10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer of in CM 1:4 for laying floor finishes including dismantling of floor tiles of any description complete all as specified and directed.

M&L for light shade vitrified ceramic tiles 9-10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm,in skirting / vertical surfaces etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick screed bed CM 1:3 over and including dismantling of wall tiles of any description complete all as specified and directed.

S&F in repairs vitreous china urinal, half stall type, white with grating and union for discharge pipe, 32 mm waste coupling and waste pipe including providing and fixing plugs bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement complete all as specified and directed.

S&F in repair vitreous china wash down water closet pan (pedestal pattern) white including 10 liter capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float, handle including brackets, 32mm dia flush pipe and PVC connection 15mm with PTMT nuts of length 450/600mm as suitable complete all as specified and directed.

S&F in repair vitreous china squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including 10 litre PVC flushing cistern and flush pipe and PVC connection 15mm with PTMT nuts of length 450/600mm as suitable complete all as specified and directed.

S&F in repair vitreous china wash basin oval type white flat back size 580x450 mm excluding taps waste chain and plug and porcelain stopper but including brackets including 15 mm bore centre hole mixer fixed in repair, complete all as specified & directed.

S&F in repair 15 mm bore bib taps, CP fancy type screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified.

S&F in repair 15 mm angle valve/stop valves, CP fancy type cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, all as specified and directed

S&F in repairs 125mm brass chromium plated shower roses including fixing to steel pipe etc complete all as specified and directed.

S&F grating doom 125/110 mm dia with/without hole of CP, all as specified and directed

S&F 1000 litre capacity rotational moulded triple layer polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including dismantling old tank all as specified.

S&F in repair 110 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in walls/trenches or in floors including all Tees, elbows, sockets etc fittings complete, all as specified and directed

S&F in repair 75 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in walls/ trenches or in floors including all tees, elbows, sockets etc fittings complete, all as specified and directed

S&F in repair 40 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors including all Tees, elbows, sockets etc fittings complete, all as specified and directed

S& F PVC ( SWR ) floor/nahani trap plain with grating including jointing with solvent cement of 110mm/75 mm dia etc complete all as specified and directed.

S&F 40 mm outer dia 3-layer PP-R polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc including taking up or down steel/PPR tubing and connections, including cleaning for refixing or removal to store, all as specified and directed

S&F 32 mm outer dia 3-layer PP-R polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc including taking up or down steel/PPR tubing and connections, including cleaning for re fixing or removal to store, all as specified and directed

S&F 20 mm outer dia 3-layer PP-R polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc including taking up or down steel/PPR tubing and connections, including cleaning for refixing or removal to store, all as specified and directed

S&F 40 mm PP-R gate valves (brass insert) as per requirement of the site, all as specified and directed

S&F 32 mm PP-R gate valves (brass insert) as per requirement of the site all as specified and directed.

S&F 20 mm PP-R gate valves (brass insert) as per requirement of the site all as specified and directed.

S&F in repair 28-30 mm dia curtain rods, mild steel (coloured - in wood finish or any other colour approved by user) with suitable fixing brackets and 02 x decorative finials for each curtain rod and all other accessory complete all as specified and directed.

M&L for treatment to sunken portions of toilets by demolition of existing treatment of any description and thickness (to including tiles, concrete, sanitary fittings etc), removal of rubbish outside MoD land, 10 mm thick plaster in CM 1:4 with water proofing liquid conplast 421 of Make - Fosroc or equivalent as specified and applying one coat of each Nittoproof 100 and Nittoproof 120 of Ms Fosroc or equivalent as specified on plastered surface and rendering again 10 mm thick plaster in cement mortar 1:4 mixed with conplast 421 of Ms Fosroc or equivalent in sunken portion and CI pipe joints shall be filled/jointed with mixture of cement, fine sand and Nittoproof 130 of Ms Fosroc or equivalent as specified and provide hole in the wall to fix 20 mm dia GI spout 600 mm long and PCC 1:5:10 or red bajri/brick bats filling in sunken portion and finished top layer with 75 mm thick PCC in 1:2:4 to receive tiles all as specified.

Demolition of concrete of any description and in any position not otherwise specifically provided for, all as specified and directed

M&L 75 mm thick PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate) laid in alternative bays as in plinth protection including finishing the surface even & fair & filling the joints with mastic filling i.e one part of bitumen 85/25 and 3 parts of sand by weight complete all as specified & directed by Engineer-in-Charge.

M&L TMT steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, all as specified and directed

M&L TMT steel bars 5mm dia and over upto and including 10mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, all as specified and directed

S&F for TMT bars 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified.

M&L for precast concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) in manholes covers set in CM 1:4 including necessary form work complete all as specified and directed. Note :-Reinforcement will be measured and paid separately.

M&L for plain cement concrete 1:2:4, type B1 (using 20mm graded stone aggregate) in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including form work all as specified and directed

M&L for cement concrete 1:4:8 type D2 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete complete, all as specified and directed

M&L providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand all as specified and directed

M&L providing, cement concrete in roof kerbs or mud stops, filling the gaps of wall and roof sheet, and similar works rounded or chamfered on edges, all as specified and directed

M&L for 25 mm thick cement concrete 1:2:4 type B- 0, (using 12.5mm graded stone aggregate) as in floors base of tiles, all as specified and directed

M&L for chequered cement concrete tiles 30cm X 30cm and 25mm thick, with grey cement and no pigments set, jointed in neat cement slurry in floors over and including 15mm thick screed bed in CM 1:4, all as specified and directed.

Excavating in trenches (Manual) n exc 1.5 m wide and n exc 1.5 m in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, laying of pipe/cable etc. n exc 10 sq m on plan and getting out in any type of soil complete all as specified and directed.

M&L for plain cement concrete 1:4:8 type D-2 nominal mix (using 40mm graded stone aggregate) as in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for internal dia of pipe 150 mm (thickness of bed shall be 15 cms), all as specified. Note(i) :- The unit rate include for use of form work. (ii) Width of bed shall be outer dia of drain pipe plus 30 cms haunching shall be as per MES SSR-part-I/Part-II

M&L for reinforced concrete pipes 150 mm dia, class NP2, laid and jointed with collars complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm., all as specified and directed

Removing excavated material nexc 50 m and depositing where directed at a level n exc 1.5 m above the starting point complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and average 15cm deep and getting out in any type of soil., all as specified and directed.

Excavating over areas not exceeding 1.50 meter deep and getting out in any type of soil, all as specified and directed.

-Ditto- all as per item ser No 93 but exc 1.5 mtr n.exc 3.0 mtr

M&L for cement concrete in foundations, filling and mass concrete 1:2:4, type B2 (using 40 mm graded stone aggregate) including compaction of concrete, curing etc. complete, all as specified and directed.

M&L for sand filling under floors or in foundations or for underground cable including watering and consolidation complete, all as specified and directed

M&L for 50mm thick screed bed or bedding layer over and including 100 mm thick PCC after application of two coats two pack acrylic polymer modified cementious water proofing coating, all as specified and directed

M&L for form work to faces of walls, retaining walls, abutments parapets and staircase railings and similar work including attached pilasters, buttresses etc. vertical or to batter fair finished surfaces of concrete complete all as specified and directed.

M&L for form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), fair finished surfaces complete all as specified and directed.

M&L for form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n.exc 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n.exc 20cm wide fair finished surfaces of concrete complete all as specified and directed.

M&L RCC (nominal mix) 1:1:5:3, type 'A' (using 20mm graded stone aggregate) as in foundation, including rafts, footings, foundation beams, plinth beams, bases for columns etc; basement slabs, under reamed piles and mass concrete, all as specified and directed.

M&L RCC (nominal mix) 1:1:5:3, type 'A' (using 20mm graded stone aggregate) as inwalls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses complete all as specified and directed.

M&L RCC (nominal mix) 1:1:5:3, type 'A' (using 20mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Removing excavated material exc. 1.50 km but n exc. 5 km and depositing where directed, all as specified and directed.

S&F framed work as in doors or gates of angel or other sec with gussets plates, rails, braces, etc., complete drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fitting (exclusive of steel, sheeting or other covering, running rails and guides) and hanging also fastening and fixing complete, all as specified and directed.

S&F for 0.5 mm thick impermeable polythene, all as specified and directed.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any ) of foundation and plinth beams, and similar work, vertical or to batter finished even and fair complete, all as specified and directed.

M&L for formwork to sides of pillars, posts, struts, piers, columns and stanchions finished even and fair complete, all as specified and directed.

M&L for formwork to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports overhangs etc also splays between floor and beams etc finished even and fair complete all as specified and directed.

M&L for TMT bars 5 mm dia and over upto and including 10 mm dia cut to length bent to shape required including cranking, bending spirally and binding with steel wires (annealed) not less than 0.90 mm dia as in stirrups, spacers and binders complete all as specified and directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6, complete all as specified and directed.

M&L for rendering plaster 15mm thick on fair face of brick work in cm 1:6 all as specified finished even and smooth without using extra cement complete all as specified and directed.

M&L two coats of cement base paint over a coat of alkaline resistant primer on new surfaces of walls including preparation of surfaces complete all as specified and directed.

M&L for preparation of new surfaces plastered or unplastered and applying two coats of oil bound distemper over a coat of alkaline resistant primer complete all as directed, all as specified and directed.

M&L for hardcore of gauge n exc. 63 mm, broken stone or boulders deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed

S&F roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections)of Fe-290 (Gde E-165) including distance pieces, cleats etc., all as specified and directed

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as complete all as specified and directed.

S&F 100 mm long butt hinges medium weight, cold rolled mild steel complete all as specified and directed.

S&F 1000 ltr capacity, rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) triple layers, hoisted and fixed in position all as specified in SSR part-I complete all as specified and directed.

S&F 20mm bore ball brass valves, high pressure, with polythene float and fly nut complete screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F 25mm outer dia triple layer PP-R polypropylene random copolymer concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified and directed.

S&F PP-R gate valves (brass insert) 25mm outer dia as per requirement of the site complete all as specified and directed.

S&F 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F, PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed.

S&F, CP brass soap dish, heavy duty, fixed with chromium plated brass screws complete all as specified and as directed.

S&F, towel rail 450mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 170gms) complete all as specified and directed.

S&F corner/sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect, all as specified.

S&F in repair vitreous china wash basin white flat back size 580x450 mm excluding taps waste chain and plug and porcelain stopper but including brackets any size, including cutting for and pinning in ends of brackets including 15 mm bore CP centre hole mixer for mixing hot & cold water screwed down for iron pipe and waste pipe complete all as specified and directed.

M&L for coloured glazed ceramic tiles on vertical surface 300x 200 and 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tile fixed over and including 10 mm thick rendering in cement mortar 1:3 complete all as specified and directed.

M&L for coloured non - skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6, complete all specified and directed.

S&F false ceiling with anodised aluminium snap grid frame work for false ceiling of grid 605 x 605mm , Gypsum board of 12 mm thick with white paper layer on face side of size 600 x 600 mm or any size Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm as directed and applying two coats of distemper oil emulsion, over a coat of primer, all as specified.

S&F roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) of Fe-290 (Gde E-165) including distance pieces, cleats etc. complete all as specified.

S&F 150 mm long (Length of bolt) aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

S&F 10 liter capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float, handle including brackets, 32mm dia flush pipe and connection to pipes complete all as specified and directed.

S&F CP steel grating 75/100mm dia, complete all as specified and directed.

S&F angle valve / stop valve 15mm dia fancy type chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union complete all as specified and directed.

M&L for taking down carefully existing old burnt out / unserviceable aluminium / copper point wiring system any type/ size and any description complete for light, fan,bell,socket, power points etc complete including removing the all type of fittings & fixture alongwith it connected fixing accessories such as all switches, sockets, ceiling roses, holder,regulators,bell etc complete and removing of all the old materials from the site for to taking as a schedule of credit including making good to disturbed surfaces to match with existing surface complete all as specified and directed by EIC .

Taking down carefully ceiling fan from site and repair it if required including spray painting complete and refixing the same position with entire satisfaction of Engr-in-Charge.

Taking down carefully electric water heater from site and repair it if required including spray painting complete body and refixing of same position complete, all as specified and directed.

M&L for making single phasing point wiring system used as copper conductor wire for phase and neutral wiring system the wire made out of PVC insulated FRLS of 1100 Volt grade with having multistranded copper conductor wire of size 1.5 Sq.mm (Nominal area) ISI marked drawn through wiring system concealed on wall with the help of heavy duty ISI mark PVC conduit in any length wiring system and along with its all connected fittings accessories including providing of modular type terminal sunken boxes and duly fixed it concealed on wall or surface on wall and providing alongwith modular type back and face top covered plate frame for housing / mounting of switches sockets, regulators etc and including using /drawing of one run of single wire 1.5 sqmm PVC insulated FRLS wire 1100 Volt grade ISI marked with multistranded copper conductor wire used as a continuous earth wire for point wiring complete system and including making the good to all disturbed surfaces of wall/ceiling area of new wiring system to match it as per the existing surface of wall/ceiling etc for one light point / fan point controlled by one switch of one way point wiring system complete, all as specified & directed by EIC Note: Contractor must do internal wiring with cheasel cutting in wall/ceiling and fixed conduit and repair surface with plaster 15MM in wall/ceiling and make surface good as it is.

-Ditto- all as item No 143 above but for one switch socket combination 5 Amps on independent board.

-Ditto- all as item No. 143 above but for one switch socket outlet 5 Amps on same board with other switches.

-Ditto- all as per above sr item No 143 but using PVC insulated FRLS wire 1100 Volt grade with multistranded copper conductor wire of size 2.5 Sq. mm (Nominal area) ISI Marked for power socket point on indenpent board point wiring system and also providing of 2.5 sqmm PVC insulated FRLS wire 1100 Volt grade ISI Marked with multistranded copper conductor wire used as a continuous earth wire for power point wiring system complete, all as specified.

S&F modular type switch piano 5/6 Amps 220 Volts AC,one module complete, all as specified.

S&F modular type socket of 5/6 Amps 220 Volts AC, 3/5 multi pin type with two modular complete, all as specified.

S&F modular type switch piano of 15/16 Amps 220 Volts AC one module complete, all as specified.

S&F modular type socket of 15/16 Amps 220 Volts AC 5/6 multi pin type with two modular complete, all as specified.

S&F ceiling rose three terminal type made out of polycarbonate , isolated body complete all as specified and directed.

S&F one/two modular type step type electronic fan regulator with having hum free step alongwith speed control know complete, all as specified.

S&F in renewal of LED tube light fitting of 1x 20W/22W 220V AC decorative box type with driver, holder including LED tube light with having energy efficient type use in both warm/white type colour complete including providing of suitable type flate flexible cable for electric connection from ceiling rose to fitting complete and including taking down of old fitting all as specified & directed .

S&F in renewal of LED mirror light fitting with high out put diffuser 2 feet long of 10 Watt 220 volt AC decorative type with driver holder and LED lamp with having energy efficient type use in both warm/white type colour complete light fitting set all as per existing fitting type/ size of sample /model and make and including providing of suitable type flate flexible cable for electric connection from ceiling rose to fitting and makong electric connection and including taking down of old fitting all as specified and directed.

S&F in repair surface mounted LED bulk head luminaries light fitting of rated capacity 10W including LED lamp & driver suitable used for out door type with dust and water proof with energy efficient complete and including providing of suitable type of flat flexible two/three core cable and making electric connection complete all as specified and directed.

S&F in renewal of LED street light fitting of rated capacity 25 Watt 230 Volt AC fixed in Bldg outside with having LED driver, lamp bracket with impact and corrosion resistant with lense embedded including thermal management in multiple optics complete with IP 65/66 protectiuon suitable for out door type made out of high pressure die cast hosing with heat resistant glass complete including providing of suitable size of dia GI pipe light grade bracket and it to match/setting the new fitting fixture hole attachment system of suitable bracket length upto 1.0 mtr long of sizes 25 mm dia and make to shape / bend of 120 degree angle including duly fixed alongwith existing pole /bldg wall/ roof with the help of 02 Nos of MS fixing clamp alongwith nut bolt and including providing of suitable type of flate flexible two/three core cable and makong electric connection and including taking down of old fitting all as specified and directed.

Dismantling unserviceable main switch/DBs with MCBs complete all as specified.

S&F of sheet metal enclosure box duly powder coated & framing work with locking system and having double door fixing arrangement system suitable of size/type for vertical type distribution board vertical loadline type of rating VTPN 4 way type 415 Volt 3 phase AC supply holding system with IP protection rating with ISI marked and having fitted neutral and earth link bus bar and mounting base channels and blanking plates suitable for holding of main MCCB as incommer and out going MCB complete system alongwith providing and mounting in side of DB box of 01 No of MCCB TP 160 Amps with breaking rupting capacity 25 KA and having adjustable setting type and also providing of 12 Nos of MCB SP 63 Amps 10KA 'C' curve type of the same manufacture make as per of distribution board make complete set and including dully fixed surface on wall or concealed in wall and making all necessary electrical and also refixing the electric meter and its wiring connection including taking down of existing meter and DBs complete all as specified and directed by EIC.

S&F of sheet metal enclosure box duly powder coated & framing work with locking system and having double door fixing arrangement system suitable of size/type of distribution board of rating SPN 12 way type 220 Volt AC supply system with IP protection rating with ISI marked and having neutral and earth link bus bar and mounting base channel suitable for holding MCBs incommer and s outgoing system complete set and including dully fixed surface on wall or concealed in wall and making all necessary electrical and also refixing the electric meter and its wiring connection including taking down of existing meter and DBs complete all as specified and directed by EIC.

-Ditto- all as per item Ser No 159 but distribution board type & Size of rating capacity SPN 8 way system complete all as specified .

S&F MCB SPN 40 to 63 Amp, 240 Volts, with breaking capacity 10 kA rupturing capacity, 'C' series 50 HZ AC supply and also making suitable size/type of electric wiring connection complete all as specified and directed.

S&F MCB SP 06 to 32 Amp, 240 Volt, 10 kA rupturing capacity 'C' series 50 HZ AC supply and also making suitable size/type of electric wiring connection complete all as specified and directed.

Supply and fixing of sub main wiring system with two runs PVC insulated FRLS wire,1100 Volt grade with multistranded copper conductor wire of size 3 Run of 10 Sqmm and 1 Run of 10 Sqmm (Nominal area) (ISI Marked) any type any length drawn through in heavy duty ISI mark PVC Casing capping / PVC conduit of suitable size along with its all fittings and connected accessories and duly fixed concealed on wall or surface on wall including taking down old unserviceable sub main wiring system complete and making good all disturbed surfaces match to the existing surface complete all as specified and directed . Note: Two runs of 10 sqmm and one run of 10 sqmm cable and one run of casing capping shall be measured as one RM

-Ditto- all as per item Ser No 163 but cable of size/type single core of 2 run of 6 sqmm and 1 run of 6 sqmm (Nominal area) ISI marked complete all as Specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60 Cm X 60 Cm X 6 mm thick buried directly in ground vertically to a depth not less than 2.25 mtr deep below ground level with top edge of earth plate at a depth not less than 1.5 m below normal ground level and connected to galvanised earth lead wire 4.0 mm dia by means of bolts, check nuts and washers of galvanised steel and to be protected by GI pipe 15 mm bore light grade & connected to earth test point/main switch board or main control board and also providing charcoal or coke and salt in alternative layers, necessary excavation and earth work in any type of soil all as shown in Electrical Plate No 3 of SSR part -I. and also making arrangement of 20 mm dia bore galvanised iron pipe (medium grade) for water and making funnel, wire mesh, and also including provision of concrete pit cover framing work in PCC (1:2:4) type B-1 using 20mm graded of stone aggregate with XPM (weight not less than 4 Kg/Sqm) and outer frame work of angle iron 25x25x6mm with top concrete pit cover and handle for lifting of cover complete work all as specified and directed . .

S&F of rigid non metalic PVC conduit of size 20/25 mm bore heavy duty with all fitting laid in trenches/wall including providing clamping arrangement for holding of pipe on wall in proper size of clamps,nut bolt, and washer etc complete all as specified and directed.

S&F GI earth continuity earthing lead of size 4 mm dia bore galvanised iron or steel wire with all fitting duly laid in trenches/wall including providing clamping arrangement for holding on wall in proper size of clamps, nut bolt and washer etc complete all as specified and directed.

Supply, laying and testing of LT cable XLPE insulated screened, PVC bedded galvanized steel strip or wire armoured electric power cable (heavy duty) with aluminium conductor 1100 volt grade cross sectional area of size 35 sqmm 3.5 core including laid in trenches or fixing on poles or passing through pipes complete including taking out of old unserviceable cable any type any size complete all as specified and directed.

M&L for brick covering width equal to length of brick for mechanical protection to cable with well burnt sub class 'B' bricks laid dry flat all as specified and directed.

S&F GI pipe 40mm bore medium grade with all fitting laid in trenches /under road/floor/pole/wall for protection of cable including providing clamping arrangement for holding of pipe on pole/wall in proper size of clamps,nut bolt and washer etc complete all as specified and directed.

M/S Tajamul Ah Buchh (BID ID -3443557)

M/S BASHIR AHMAD MIR (BID ID -3441527)