Improvement of Karma yogi Training centre at Danapur Division under ADEN/HQ/DNR

Item Breakup - B-Sch-B

wall thickness of 1.9 +/- 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm). 10.0 STEEL WORK 10.28 Providing and fixing stainless steel ( Grade 304) Kg 200 612.25 122450 railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & 17 stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). 11.0 FLOORING 11.41S VITRIFIED FLOOR TILES Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved 11.41 make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ s q m including grouting the joints with white cement and matching pigments etc., complete. 18 11.41.2 Size of Tile 600x600 mm Sqm 86 1416.65 121831.9 12.0 ROOFING DANAPUR DIVISION-ENGINEERING/EAST CENTRAL RLY Providing, fixing and embedding sand cast iron accessories for rain water pipes in the masonry 12.40 surrounded with 12 mm thick cement mortar of the same mix, as that of masonry (lead caulking will be paid for separately): Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 12.41 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 19 12.41.2 110 mm diameter Metre 50 319.75 15987.5 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes 12.42 conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 12.42.4 Single tee without door 20 12.42.4.2 110x110x110 mm Each 5 190.75 953.75 12.42.5 Bend 87.5 degrees 21 12.42.5.2 110 mm bend Each 5 132 660 Providing & fixing false ceiling at all height including providing & fixing of framework made of special section, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleat of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at 1200mm c/c, one flange fixed to the ceiling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25 x10 x0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I chanels 45 x15 x 0.90mm running at the spacing of 1200 mm c/c, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having lips of 10.5mm, at 450mm c/c, shall be fixed in a direction perpendicular to G.I intermediate channel with connecting clip made out of 2.64mm dia x 230mm long G.I wire at 12.59 every junction, including fixing perimeter channels 0.50mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/ partitions with the help of Rawl plugs at 450mm centre, with 25mm long dry wall screws @ 230mm interval, including fixing of Calcium Silicate Board to ceiling section and perimeter channels with the help of dry wall screws of size 3.5 x25mm at 230mm c/c, including jointing & finishing to a flush finish of tapered and square edges of the board with recommended jointing compounds, jointing tapes,finishing with jointing compounds in three layers covering up to 150mm on both sides of joints and two coats of primer suitable for boards, all as per manufacture's specification and also including the cost of making opening for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specificaton and direction of the Engineer in charge but excluding the cost of painting with: 12.59.1 8 mm thick Calcium Silicate Board made with Sqm 85 1330.4 113084 Calcareous & Siliceous materials reinforced with 22 cellulose fiber manufactured through autoclaving process. 13.0 FINISHING DANAPUR DIVISION-ENGINEERING/EAST CENTRAL RLY 13.1S CEMENT PLASTER (IN FINE SAND) 13.1 12 mm cement plaster of mix : 23 13.1.1 1:4 (1 cement: 4 fine sand) Sqm 40 294.85 11794 24 13.1.2 1:6 (1 cement: 6 fine sand) Sqm 200 282 56400 13.25 Extra for plastering: 13.26 Providing and applying plaster of paris putty of 2 Sqm 240 214.3 51432 25 mm thickness over plastered surface to prepare the surface even and smooth complete. Distempering with oil bound washable distemper 13.41 of approved brand and manufacture to give an even shade : 13.41.1 New work (two or more coats) over and Sqm 1000 162.55 162550 26 including water thinnable priming coat with cement primer 13.44S EXTERIOR FINISHING Finishing with Deluxe Multi surface paint system 13.48 for interiors and exteriors using Primer as per manufacturers specifications : 13.48.1 Two or more coats applied on walls @ 1.25 Sqm 1000 158.95 158950 27 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm Painting with synthetic enamel paint of 13.61 approved brand and manufacture to give an even shade : 28 13.61.1 Two or more coats on new work Sqm 20 131.45 2629 15.0 DISMANTLING AND DEMOLISHING Demolishing cement concrete manually/ by mechanical means including disposal of material 15.2 within 50 metres lead as per direction of Engineer - in - charge. 15.2.1 Nominal concrete 1:3:6 or richer mix (i/c cum 5 2007.1 10035.5 29 equivalent design mix) Demolishing brick work manually/ by mechanical means including stacking of 15.7 serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. 30 15.7.4 In cement mortar cum 5 1698.45 8492.25 Dismantling tile work in floors and roofs laid in 15.23 cement mortar including stacking material within 50 metres lead. 31 15.23.1 For thickness of tiles 10 mm to 25 mm Sqm 85 60.5 5142.5 15.56 Dismantling old plaster or skirting raking out Sqm 200 45.05 9010 joints and cleaning the surface for plaster 32 including disposal of rubbish to the dumping ground within 50 metres lead. 16.0 ROAD WORK 16.1S ROADS Dry brick pitching half brick thick in drains 16.12 including supply of bricks and preparing the surface complete : 16.12.1 With common burnt clay F.P.S. (non modular) Sqm 15 607.2 9108 33 bricks of class designation 7.5 Providing and applying tack coat using bitumen emulsion conforming to IS:8887, using emulsion 16.31 pressure distributer including preparing the surface & cleaning with mechanical broom. DANAPUR DIVISION-ENGINEERING/EAST CENTRAL RLY Providing and laying bitumen mastic wearing course (as per specifications) with industrial bitumen of grade 85/25 conforming to IS : 702, prepared by using mastic cooker and laid to required level and slope, including providing antiskid surface with bitumen precoated fine grained hard stone chipping of approved size at 16.37 the rate of 0.005 cum per 10 sqm and at approximate spacing of 10 cm centre to centre in both directions, pressed into surface protruding 1 mm to 4 mm over mastic surface, including cleaning the surface, removal of debris etc. all complete. (Considering bitumen using 10.2% as per MORTH specification). 34 16.37.1 25 mm thick Sqm 400 726.95 290780 16.49S MISCELLANEOUS Providing and laying gang saw cut 30 mm thick, mirror polished pre moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar 16.87 locations, laid over 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of Engineer-in-Charge. 16.87.2 With granite stone of all colour except black, Sqm 20 4537.25 90745 35 cherry/ruby red of area less than 0.50 sqm. 17.0 SANITARY INSTALLATIONS 17.31 Providing and fixing 600x450 mm beveled edge Each 2 1411.15 2822.3 mirror of superior glass (of approved quality) 36 complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. 17.33 Providing and fixing 600x120x5 mm glass shelf Each 2 942.15 1884.3 with edges round off, supported on anodised 37 aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. 21.0 ALUMINIUM WORK Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with 21.1 required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum 21.2 doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. 21.2.2 Pre-laminated particle board with decorative Sqm 31 951.05 29482.55 38 lamination on both sides DANAPUR DIVISION-ENGINEERING/EAST CENTRAL RLY Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. 21.3 complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): 21.3.2 With float glass panes of 5 mm thickness Sqm 2 1325.55 2651.1 39 (weight not less than 12.50 kg/sqm) 21.5 Providing and fixing powder coated aluminium Kg 60 674.6 40476 work (minimum thickness of powder coating 50 micron) consisting of tee/ angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P. brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm 40 centre to centre and fixing the frame work to G.I. level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in- charge (level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately). 26.0 NEW TECHNOLOGIES AND MATERIALS 26.73S PREFAB/PRECAST TECHNOLOGY 26.91 Providing and fixing factory made 18 mm thick Sqm 95 3136.65 297981.75 single extruded WPC (Wood Polymer Composite) solid plain white colour board Jali, CNC (Computer numeric control) routed of approved design by Engineer-in -charge which are machine cut for duct/shaft covering, partitions and facades comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium corbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gm s) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) m i n i m u m compressive strength 50 N/mm2, 41 modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with properties of being termite/borer proof, water/moisture proof and fire retardant and fixing on M.S (mild steel) frame made of 25 x 25 x 1.5 mm square hollow box section including applying a priming coat of approved steel primer, placed at grid made at 1.0 x 1.0 m or as per requirement at site with necessary stainless steel fasteners and SS screws etc., all complete as per direction of Engineer-In- Charge. (Note: M.S (mild steel) framework with priming coat and necessary SS fasteners and SS screws shall be paid separately. Total 2286943.52