80867 Adn altn and Special repairs to Bldg No P13 P28 P29 EPs MD Accn at TRV Port Blair

Amount

Dismantling floor, hearth or wall tiling including CM bedding, removing rubbish off the premises complete all as specified and as directed by Engineer-in-Charge.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons, riser of steps, skirting, dado etc laid in any mortar complete all as specified and as directed by Engineer-in-Charge.

Demolition of cement concrete un-reinforced in any position and paving not exc 15cm thick (above or below ground level) complete all as specified and as directed by Engineer-in-Charge..

M&L for PCC (1:2:4) type B-0 (using 12.5 mm graded aggregates) as in sub base 25mm thick complete all as specified and as directed by Engineer-in-Charge.

M&L for non-skid coloured ceramic tiles 8 to 10mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, including 15mm thick screed bed in CM 1:4 complete all as specified and directed by Engineer-in-Charge..

All as per item No 05 above but thickness of tile 7 to 8mm including PVC corner beads etc., as in skirting / dados etc. including backing coat 10mm thick in cement mortar 1:3, complete all as specified and as directed by Engineer-in-Charge.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (Square / rectangular) area of each tiles exc 0.06 Sqm but n. exc 0.11 Sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match including 15mm thick screed bed of CM (1:4) bedding complete all as specified

M&L for glazed ceramic designed coloured tiles as in vertical surfaces of size 300x450x7 to 8 mm thick set and jointed in neat cement slurry and pointed in coloured cement to match designed incl 10 mm thick backing coat in CM (1:3) complete all as specified.

M&L 20 mm to 25 mm thick polished cudappah stone slab in shelves in cupboard & kitchen cabinet without screed bed, completed all as specified as and as directed by Engineer-in-Charge.

M&L 18 mm to 20mm thick granite work (table rubbed and polished) as in cooking platforms slab and window cill / corner shelves etc fixed after and including15 mm thick screed bed (1:4), pointing the joint by using (1:2) of white cement, marble dust and colour pigment, all as specified. (Note : Colour of granite shall be as approved by Engr-In-Charge) including Rounding ( chamfering) to edge of granite slab edge with mirror polishing such complete.

Dismantling of ceiling boarding including grid of any description fixed in any position with nails complete all as specified and as directed.

S&F for anodized aluminum snap grid frame work for false ceiling incl hangers 6 mm dia, GI (up to 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3mm size 60 mm long and expansion hold fasteners 12.5mm dia, 40mm long complete all as specified and as directed by Engineer-in-Charge.

M&L for 6mm thick non asbestos fiber cement building design board(E-board) of size 605 x 605 mm fixed or laid to aluminum grid work with screws and including preparation of surface with two coat of oil bound distemper over a coat of primer complete all as specified and as directed.

Taking down chowkhats or frames of doors, windows, CB and kitchen cabinets with shutters without taking off shutters from frame exe 1.5 Sqm and n.exc 4 Sqm each

Taking down chowkhats or frames of doors, windows, CB and kitchen cabinets with shutters without taking off shutters from frame n exe 1.5 Sqm each

S&F IInd class hardwood plain solid straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints.

S&F for 35mm thick flush shutters, 30mm solid core construction, with block board core and plywood face panels, commercial type on both sides.

S&F 35mm thick, IInd class hard wood glazed and skeleton shutter open rebated and prepared to receive gauze, etc. ( without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing gauze etc size of members of shutters as specified in as Part I Ses 8 Clause 8.24(a) all as specified and as directed by Engineer-in-Charge.

S&F Solid PVC door frame of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, fixed in opening as per specification complete all as specified and as directed.

S&F for Factory made solid PVC moulded with particle board core door shutter 28 to 30 mm thick (style)with 2,4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face and 2mm plain colour PVC sheet on back face, supplying and fixing in frame at site as per specification and drawing all as specified

Taking down shutters of any description exe 1.0 Sqm and n.exc 2 Sqm each.

Taking down shutters of any description exe 1.0 Sqm and n.exc 2 Sqm each & refixing in same opening complete all as specified and as directed.

S&F Banks, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; will ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe410-0 or Fe 310-0

M&L cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in lintel upto 1.5m clear span, steps, bed plates, kerb & coping including necessary formwork.

S&F stainless steel but hinges 100mm size.

S&F extruded aluminum alloy handle fabricated type anodized 150mm long.

S&F extruded aluminium alloy handles fabricated types, anodised, each 100mm long.

S&F Aluminum anodized barrel tower bolt of extruded section 150mm long

S&F aluminium anodised barrel tower bolt 75mm long complete all as specified.

S&F extruded aluminium anodised 75mm long hasp and staple, safety type incl bolt to hinge plate and fixed with screws complete all as specified.

S&F in repairs mild steel 300mm, ordinary rat tail rod pattern springs, including roller and roller plate complete

S&F Aluminum alloy anodized sliding door bolt 300mm long with hasp and staple (bolt type) and fixing bolts and sliding bolts of extruded such or cast aluminum alloy

S&F 2nd class HW plain fillets rectangular or triangular section wrought fixed with scews/nails exc 13 sqcm and n.exc 25 sqcm complete all as specified and as directed.

S&F continous (Piano) hinges mild steel bright finish or electrogalvanised, width of flaps 40 mm

S&F auto hinges stainless steel size 75mm suitable for kitchen cabinets.

M&L preparing new wood based surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified

S&F for powder coated aluminium shutters of sliding/ openable/ fixed/ fully glazed/partially glazed/fully gauge/ Skelton door/ window and ventilator frame etc., with glass or gauge and panels with prelaminated particle board inserts, side hung type, without sash bars, using standard aluminium sections including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, roller for sliding windows, locking arrangement, anodized aluminium fittings such as handles, required hinging device etc. complete all as specified and as directed. Note : (i) Glass panes / wire mesh will be measured & paid separately as supplied only (ii) Weight of aluminium sections only shall be accounted for payment purpose. However unit rate quoted shall be deemed to include for cost of rubber beading, glazing clips, neoprene packing, fittings such as handles, butt hinges, tower bolts and fixing only of panel inserts of glass/ particle board/ gauge, etc. (iii) The windows frame shall be fitted to the opening with suitable fixing arrangements. (iv) Any minor addition/alteration and making good the damaged portion shall be included in the unit rate.

Supply only plain sheet glass 4.0 mm thick ordinary quality and glazing with aluminum glazing clip in aluminum window shutter not exc 0.5 Sqm in each pane.

Supply only figured glass, pin head type sheet glass 4.0 mm thick ordinary quality and glazing with aluminium glazing clip in aluminium window shutter not exc 0.5 Sqm in each pane.

S&F aluminium alloy wire cloth 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples all as specified and as directed by Engineer-in-Charge.

Supply only Aluminium alloy wire cloth 0.45 mm nominal dia of wire average width of aperture 1.40 mm and fixed with aluminum wire staples all as specified and as directed by Engineer-in-Charge.

Dismantling of 110mm dia cast iron/PVC pipes incl bends/branch pieces jointed in cement mortar and taking out all as specified and as directed by Engineer-in-Charge.

S&F for 110mm dia PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints fixed to wall etc using synthetic rubber adhesive cement solvent complete all as specified.

S&F for 110mm dia PVC (SWR) bends any radius complete all as specified.

S&F for 110mm dia PVC (SWR) branch piece single (single Y) equal or unequal complete all as specified.

S&F for 110mm dia PVC (SWR) vent cowl complete all as specified.

Dismantling of 75mm dia cast iron/PVC pipes incl bends/branch pieces jointed in cement mortar and taking out all as specified and as directed by Engineer-in-Charge.

S&F for 75mm dia PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints fixed to wall etc using synthetic rubber adhesive cement solvent complete all as specified.

S&F for 75 mm dia PVC (SWR) grade bends of any radius

S&F PVC (SWR) branch piece, single (Single Y) of radius equal or unequal, 75mm dia.

S&F PVC (SWR) vent cowl, 75mm dia.

M&L PVC (SWR) multi floor trap in repairs 75mm with grating including jointing with solvent cement complete all as specified.

Supply and fixing in repairs vitreous china wash basin white, flate back pattern size 550 X 400mm including 32 mm CP waste coupling, chain and plug, waste fittings, PVC connection of 450mm long, union and waste pipe 32mm dia or required length and all necessary inlet, out let connections complete all as specified. Make : M/s Parryware (Super line)/ M/s Cera (1st Quality).

S&F in repairs 15 mm bore pillar taps, cast copper alloy, chromium plated fancy type screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts complete all as specified. (Make Jaquar Cat No. FLR-5011N)

S&F in repairs for providing bib taps cast copper alloy chromium plated fancy type with crutch or butter fly handle screwed down for Iron pipe or for brass fancy for CP brass fancy type 15mm dia complete all as specified. (Make Jaquar Cat No. FLR-5047N)

S&F in repairs for providing angular stop cock cast copper alloy fancy type screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union and fixed for 15mm bore of pipe. (Make Jaquar Cat No. FLR-5053N)

S&F in repairs,stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions & fixed, fancy type, chromium plated with long shank and cup (concealed type) for 15 mm completed all as specified.

M&L in repairs for providing chromium plated overhead shower rose 150mm size with shower arm 150mm length with or without swivel joints fixed to 15 mm bore of pipe.

Taking down damaged aluminium windows including all fittings etc of any and making good the damaged portion of opening for fixing of new window.

S&F in repairs vitreous china wash down white water closet pan (pedestal pattern with trap incl connecting to drain and flushing pipe, antisyphonage pipe incl PVC seat cover etc complete all as specified. Make: M/s Hidustan/ Parryware (Super line) / Cera (1st Quality) / Prayag.

S&F in repair PVC valveless syphonic action type flushing cistern 10 ltr capacity white with intel ball valve float flush pipe and handled including brackets complete all as specified and as directed. Make: M/s Hidustan/ Cera (1st Quality) / Johnson/ Prayag.

S&F in repairs, Chromium plated tubular towel rail 20mm dia ,D type 60 cm long between flanges . Make: M/s Hidustan/ Cera (1st Quality) / Johnson/ Prayag.

S&F in repairs wardrobe aluminium hooks set of six, 50mm to 60mm width complete all as specified and as directed. Make: M/s Hidustan/ Cera (1st Quality) / Johnson/ Prayag.

S&F in repairs Brass chromium plated Soap dish of any type, fixed to plug with CP brass screws complete all as specified and as directed. Make: M/s Hidustan/ Cera (1st Quality) / Johnson/ Prayag.

S&F in repairs PVC connection 15 mm dia and 600 mm long. Make: M/s Prayag/ Nova / Anchor/Soma/ Emsons.

S&F in repairs 1mm thick Stainless steel sinks with drainage board in kitchen with plugs, waste coupling, washers and waste pipe incl bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipes fixed on granite platform, over all size 915 X460mm bowl size 410mm X 330mm X 160mm complete all as specified. Make : Nirali

Labour for drilling holes with drill machine with electric driven for gas pipe etc not exc 25 mm dia Upto 10cm depth in granite stone etc

S&F in repairs 20mm dia, Harrison rails, anodized aluminium alloy with fixing curtain brackets, stops, rollers etc complete all as specified and as directed.

Taking up or down 15mm dia steel tubing connection, including cleaning for refixing or removal to store

Taking up or down 20mm dia steel tubing connection, including cleaning for refixing or removal to store

Taking up or down 25mm dia steel tubing connection, including cleaning for refixing or removal to store

S&F for 15mm bore unplasticised PVC pipe of pressure ratings 10kgf/Sqcm including all fittings fixed to wall, ceilings and floors etc complete all as specified. Make: M/s Supreme/ Prince/ Finolex/ Sudhakar.

S&F for 15mm bore CPVC pipe SDR11 & plain CPVC SDR 11 fittings laying in floors/walls including all fittings etc complete all as specified. Make: M/s Supreme/ Prince/ Finolex/ Sudhakar.

S&F for 20mm bore unplasticised PVC pipe of pressure ratings 10kgf/Sqcm including all fittings fixed to wall, ceilings and floors etc complete all as specified. Make: M/s Supreme/ Prince/ Finolex/ Sudhakar.

S&F for 25mm bore unplasticised PVC pipe of pressure ratings 10kgf/Sqcm including all fittings fixed to wall, ceilings and floors etc complete all as specified. Make: M/s Supreme/ Prince/ Finolex/ Sudhakar.

S&F in repairs for providing 25mm dia Gun Metal, globe or gate valves with iron wheel head, screwed both ends for iron pipes Make: Zolata/ Leader/ Upadhaya

S&F in repairs for providing 20mm dia Gun Metal, globe or gate valves with iron wheel head, screwed both ends for iron pipes. Make: Zolata/ Leader/ Upadhaya

Cutting chases in PCC block walls for concealed water tubing etc., and making good, cutting not exc 10 cm girth complete all as specified and as directed by Engineer- in- charge.

Dismantling structural steel work complete all as specified.

M&L for mild steel section for framed work such as grills, gratings, etc. with ends of bars shouldered and or riveted or forged into spikes, framed guard bars and similar work conforming to Grade Fe-290.

M&L for preparation of new steel surfaces over 10 cm in width or girth not otherwise described and applying 2 coats of synthetic enamel paint over one coat of red oxide primer all as directed.

Demolition of cement concrete of any description and in sunken floor /roof padding etc not otherwise specifically provided for.

M&L for PCC (1:2:4) type B-0, using 12.5 mm graded stone aggregate as in roof padding / sunken floors and similar work using WPC @ 3% by wt of cement complete all as specified. Note : WPC shall be measured and paid separately

M&L 12 mm thick Plaster on RCC roof slab/sunken with CM ( 1:4 ) including water proofing compound @ 3% by weight of cement shall be carried out as specified. Note : WPC shall be measured and paid separately

M&L for preparing plastered surfaces and applying primer @ 0.30/Kg per sqm and applying tack coat of bitumen 85/25 @ 1.2 kg/Sqm laying 3 mm thick polyster reinforced APP modified water proofing membrane weighing not less than 3.5kg/sqm and application of a coat of hot bitumen 85/[email protected]/Sqm over the membrane all as specified and as directed by Engineer-in-Charge.

M&L PCC (1:4:8) type D2 using 40mm graded stone aggregate as in filling in sunken floors complete all as specified and as directed by Engineer-in-Charge.

M&L for applying a coat of reflective bituminous aluminium paint @ 0.10 Litr / sqm over bitumen membrane surface complete all as specified and as directed.

Dismantling of Precast cement concrete block walling built in CM or Cement lime Mortar complete all as specified and as directed.

M&L precast cement concrete block masonry exc. 10 cm width with solid block type C1 (1:3:6) (using 20 mm graded stone aggregate) and setting in cement mortar (1:6) all as specified.

M&L precast cement concrete solid building blocks or slabs 10 cm thick ( with plain or interlocking joint as directed) complete in walls type C1 1:3:6 (using 20 mm graded stone aggregate) and setting in cement mortar (1:6) all as specified.

Taking down cement plaster on brick /stone masonry / concrete surfaces of wall / ceiling incl raking out joints, hacking for key, scrubbing down with water etc and deposited the debris outside the MD land complete all as specified.

M&L for rendering in two layer i.e.5mm thick in CM 1:4 including mixing of water proofing compound over 10mm thick in CM (1:6) on concrete/block masonry surfaces and finished even and smooth without using extra cement all as specified. Note: WPC shall be measured and paid separately

M&L for 10mm thick plaster in CM (1:6) on fair faces of concrete/PCC block surfaces of walls finished even and smooth (without using extra cement) all as specified.

M&L for 5mm thick plaster in CM (1:3) on fair faces of concrete surfaces of ceiling finished even and smooth (without using extra cement) all as specified.

Supply only water proofing compound.

Removing loose and broken concrete surfaces carefully by chiseling / picking etc Upto a depth of 20 to 40mm from columns, beams and similar structural members cutting edges, cleaning the dismantled portion with wire brushes etc to make the reinforcement naked and remove dust, dirt and other foreign particle etc and washing with clean water all as specified. Note: Safety precaution shall be ensured by the contractor while carry out the work including necessary providing, fixing and removing, shoring, upto height 12 mtr etc complete all as specified.

Removing loose and broken concrete carefully by chiseling / picking etc upto a depth of 40 mm from soffit of slab/ roof and similar structural members cutting edges, cleaning the dismantled portion with wire brushes etc to make the reinforcement naked and remove dust, dirt and other foreign particle etc and washing with clean water including necessary providing, fixing and removing, shoring, upto height 12 mtr etc complete all as specified.

M&L for applying one coat of anti corrosive primer @ 0.25 Litres/Sqm for the steel area to exposed old and new reinforcement to the full circumference and length of bars to form unbroken 40 micron thick film all as specified and as directed. Make : Nito Zinc Primer of FOSROC or equivalent make of Dr.Fixit of Pidilite Industries or IPH-RB 107 & IPH RB- 167 of Harjas Coatings and Polymers.

M&L for applying one coat epoxy bonding agent as per manufactures instruction to old concrete surface of columns, beams, slab and similar structural members all as specified and as directed by Engineer-in-Charge. Make : Nito Bond EP of FOSROC or equivalent make of Dr.Fixit of Pidilite Industries or IPH-21 of Harjas Coatings and Polymers.

M&L for Non Shrink, cementations micro concrete mixed with 12mm graded hard stone aggregate laid in thickness 20 to 40mm in columns, beams and similar structural members including use and waste of water tight form work to facilitate pouring of micro concrete and curing as per manufacture's instruction complete all as specified Make : Rendroc RG of FOSROC or equivalent make of Dr.Fixit of Pidilite Industries or IPH-411 of Harjas Coatings and Polymers.

Taking down of damaged, loosened cement concrete /cement mortar in walls/soffits/chajjas and similar structure members up to depth of 20mm cleaning the dismantled portion with wire brush etc remove dust , dirt and other foreign particles etc and washing with water with pressure and applying bonding agent on old concrete surfaces with Nitobond SBR @ 1 ltr per 5 Sqm or as per manufacturers instruction, providing 20 mm thick High build polymer modified cement sand mortar ( 1:3) mixed with minimum 5 liters Nitobond SBR per 50 kilogram of cement of M/s FOSROC chemical ( India ) Pvt Ltd or Equivalent product of manufacturer all as manufacturers instruction including necessary scaffolding up to 12 m complete all as specified and directed.

S&F TMT steel bars 10mm dia and over, cut to length, bent to shape required, including cracking bending spirally for hooping for columns/beams, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia.

S&F TMT steel bars 5mm dia and over upto 10mm dia, as in stirrups, cut to length, bent to shape required, including cracking bending spirally for hooping for columns/beams, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia.

M&L for preparation of newly plastered wall surfaces and applying two coats of oil bound distemper over one coat of primer including leveling the surface which undulation found with cement putty etc complete all as specified and as directed by Engineer-in-charge.

M&L for preparation of newly plastered ceiling surfaces and applying three coats of white wash complete all as specified and as directed.

M&L for preparation on newly plastered external wall surface and applying two coat of weather proof (exterior grade) acrylic emulsion paint with anti fungal property over a coat of primer of the same manufacturer as that of paint complete all as specified and as directed. Make: Dulux Weather Shield Max or Apex Ultima from Asian Paints or Berger weather coat All guard.

M&L for complete removal of existing treatment on wall by scrapping, washing, cleaning etc and applying two coats of acrylic emulsion distemper over one coat primer including filling of cracks, holes and including leveling the surface undulation found with cement putty etc. all as specified and as directed by Engineer-in-Charge.

M&L for preparing old plastered surfaces of ceilings and applying one coat of white wash including filling of cracks, holes etc. with cement putty all as specified.

Demolition of reinforced cement concrete of any description and in any position not otherwise specially provided for

M&L for preparation of old wall surfaces and complete removal of existing treatment by scrapping, washing, cleaning etc and applying two coats of weather proof (exterior grade) acrylic emulsion paint with anti fungal property over a coat of primer incl crack filler in cracks where required all as specified. (Make: Dulux Weather Shield Max or Apex Ultima from Asian Paints or Berger weather coat All guard).

M&L for PCC (1:3:6) type C-2(40 mm graded aggregate) 75mm thick as in plinth protection with even and smooth finishing without using extra cement complete.

M&L for 75mm thick cement concrete (1:4:8) type D-2, (40mm graded stone aggregate) as in sub base complete all as specified and as directed by Engr-in-charge.

S&F for glossy finished chequered cement concrete tiles, bull nosed, 30cmx30cmx25mm thick set suitable for stair case jointed with grey cement and pigment and pointed in neat cement slurry including 20 mm thick screed bed of CM(1:6) in floors, risers of steps etc complete all as specified and as directed.

M&L preparing old surfaces of wood or wood based material exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of wood primer.

Taking down copper/aluminium point wiring(light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials and making good disturbed surfaces of walls, floors, etc.

Taking down fuse Unit/DBs 415 Volt/230 Volt including MCCB/MCBs

Taking down old aluminium sub main wiring of any size.

M&L for Point wiring complete with proper colour coading, phase red. yellow/ blue, neatural black and earth green including proper connection with thimbals as specified with 1100 volt grade 1.5sq.mm. (nominal area) single core PVC insulated unsheathed FRLS cable multi-stranded copper conductor drawn through and including rigid non-metallic PVC Casing & Capping of suitable size but not less than 25mm dia , with all fittings, fixed on wall/ceiling /floor including sunk pressed steel terminal boxes with 3mm thick plastic laminated sheet top cover for mounting switches/sockets/regulators etc complete as specifed (inner and outer) . along with necessary metal boxes flush mounting in the wall duly earthed with same cable as for wiring above but green in colour as continuous earthing wire complete all as specified

One light/fan point controlled by one switch 5 Amps one way.

One light point controlled by two 2-way switches.

One 3 pin 5 Amp socket out let on independent board.

One 3 pin 5 Amps socket out let on same Board

One bell point controlled by one bell push switch 5 Amps one way.

All as per item No.119 above but point wiring with 4.0 sqmm PVC FRLS insulated multistranded copper conductor suitable for one 3 pin 15 Amps socket out let, and one run of 4.0 sqmm cable for earth in green colour on independent board.

S & F switch piano flush type sinle pole, 05 Amp one way 230 V AC.Make : Anchor/Cona/Legrand

S & F switch piano flush type sinle pole, 15 Amp one way 230 V AC.Make : .Make : Anchor/Cona/Legrand

S & F switch piano flush type single pole, 05 Amp two way 230 V AC.Make : .Make : Anchor/Cona/Legrand

S & F bell push 5 Amp one way 230 V AC Make : .Make : Anchor/Cona/Legrand

S & F socket outlet 3 pin 5 Amp flush type 230 V AC Make : .Make : Anchor/Cona/Legrand

S & F socket outlet 3 pin, 15Amps flush type 230 V AC Make : .Make : Anchor/Cona/Legrand

S & F Ceiling rose PVC polycarbonate , isolated body 3 terminals 230 V complete.

S & F Electric Bell, Ding dong type working on 230 volts AC supply complete all as directed by Engineer -in- charge .Make: Anchor/Kinjal/Standard

S & F fan regulator electronic socket two module step type 120 W complete all as specified. Make : ROMA(Anchor)/Havells (Crabtree)/Legrand

Taking down carefully ceiling fan of any make, size form its location, handed over to AGE E/M store yard without any damage

S & F Ceiling fan 5 star rated, 1200mm sweep, of model No.ES-50 (white colour) working on single phase 230 volts, 50Hz AC supply complete with down rod and canopy including electric connection from ceiling rose to fan connector with PVC insulated 3 core copper cable of size of 0.75 sq mm complete all as spcified and as directed. Make: Havells (Model No. ES-50 5)/Bajaj/CG

Taking down carefully electric geyser of any make, size form its location, handed over to AGE E/M store yard without any damage

S & F Energy Efficient BEE 5 star rated water heater storage type of 25 liters capacity, vertical electric supplied and installed complete including flexible pipe for hot and cold water, dead weight pressure relese valve, Anchor fastner - 4Nos of suitable size all as directerd by Engineer-in-charge. Make: Havells(Model: Puro Turbo)/Bajaj/Racold.

Taking down carefully exhaust fan of any make, size from its location, dismantling complete, examine complete parts thoroughly, oiling, greasing all parts and complete overhauling of fan incudingl replacement of small parts such as split pin, nut bolt, screws and assembling back the fan, make fully functional, re-fixing the fan to its position including replacing and providing of twin core copper wire 23/0.0076 from fan to ceiling rose and applying spray painting to the fan with same colour of fan complete all as directed.

Taking out old burnt winding of exhaust fan motor of 300/380/450mm sweep and M& L for rewinding with new copper winding wire of same gauge with approved quality of super enameled copper winding wire including varnishing heating etc complete all as directed.

Supply and fix of fan blade for exhaust fan of 300/380 mm sweep complete all as directed.

S & F Sub main wiring with PVC insulated FRLS cable 2 single core 6 sq mm 1100 V grade with stranded copper conductor in and incl rigid PVC Casing & Capping (ISI marked) incl all specials/accessories etc and provision of PVC insulated FRLS copper conductor single core 6.0 sq mm for earth continuity all as directed. Note : 3 length of cable and one length casing caping shall be measured and paid for one length

S & F Sub main wiring with PVC insulated cable 2 single core 4 sq mm 1100 V grade with stranded copper conductor in and incl rigid PVC casing and caping on wall (ISI marked) incl all specials like joint elbow, Tee ,junction , bend etc and provision of PVC insulated copper conductor single core 2.5 sq mm for earth continuity all as directed. Note : 3 metre of cable and one metre casing caping shall be measured and paid for one running metre.

S & F single pole and neutral sheet steel powder coated Distribution board for MCBs fitted with 200 Amps rated bus bar , Neutral link ,Earth Bar and Din rail suitable for use on 240 V, 50 Hz supply double door SP&N DB system 08 ways. Make: Legrand/L&T/Havells/ABB

S & F single pole and neutral sheet steel powder coated distribution board double door 04 ways for MCBs fitted with bus bar, neutral link, earth bar and din rail suitable for use on 240 V, 50 Hz, complete all as directed.

S & F of 25 Amp RCCB `A` Type 6 KA capacity, 30 MA Make: Indo Asian(811700)/Havells/L&T

S & F Tripple pole and neutral sheet steel powder coated Distribution board vertical type for MCCBs fitted with 200 Amps rated bus bar , Neutral link ,Earth Bar and Din rail suitable for use on 415 V, 50 Hz supply double door TP DB system 04 ways Make: Legrand/L&T/Havells/ABB

S & F MCCB TPN, 160 Amps, 16 KA, 415 volts, 50Hz AC supply. Make: Legrand/L&T/Havells/ABB.

S & F MCB DP, 63 amps, 10 KA, 240 volts Make: Standard /L&T/Havells

S & F MCB SP, 6-32 amps, 10 KA , 240 volts Make: Legrand /L&T/Havells/ABB

Taking down the existing LED light fitting and keep in safe custody and refixing it in the same position after completion of repair work all as specified and as directed by Engineer-in-Charge.

Taking down carefully existing electronic energy meter of any capacity and any size handed over to AGE E/M store yard and S&F single phase kwh meter with LCD display of capacity 10-60A with optical port with tamper proof model EM101+Class 1 Base mounting all as directed. Make: L&T (cat no.WM 101BC7DDH)/Schnider/Areva. Note: All meters installed should be covered in a robust wooden panel box with sunmica sheet and locking arrangements. The rate should be includied in the item.

S & F polycabonate sheet enclosure factory made for accomdating one energy meter and one SPN MCB all as directed. Note: the rate is deemed including 40 Amp DP MCB Make : Havells/ Legrand/ L&T

Earthing complete with galvanised earth plate electrode 60 cm x 60cmx 6.15 mm thick, buried directly in ground vertically (earth pit not less than 2.25 m deep below ground level) with top edge of the earth plate not less than 1.5m below ground level , connected to GI earth wire 4 MM Dia as earthling lead by means bolts and nuts check nuts and washers of galvanized iron and connected to main switch board including watering arrangement with PCC chamber , MS funnel with wire mesh,. CI cover with frame etc including necessary excavation in any type of soil strata, returning, filling removal of soil outside MD land ,filling of charcoal and salt complete all as shown in electrical plate No. 3 of MES Sch Part I , connected to Earthing test point terminal block made of gun metal or phosphorous bronze 75x75x25mm drilled and screwed including 3 Nos 8mm dia 25mm long hexagonal head screw all as specified and directed by Engineer-in-Charge. Note: Test results shall be submitted to the Engineer-in-Charge on completion of earthing.

Taking down old XLPE sub main cable of any size.

Excavation in trenches not exceeding 1.5 M wide and not exceeding 1.5 M deep for foundation of poles, cables, pipes stays and struts etc, and getting out in soft/ loose soil complete all as specified and as directed by Engineer-in-Charge.

Returning, filling in including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick in soils complete all as specified and as directed.

Removing surplus excavated soil to a distance not exceeding 50m depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

M & L Earthing complete with galvanised steel earth plate electrode of size 60cm x 60cm x 6.0mm thick buried directly in ground (earth pit not less than 2.25m deep below the normal ground level) with top edge of plate not less than 1.5m below normal ground level connected to galvanised earth strip 32x6mm as earth lead connected by means of bolts, nuts, washers and check nuts made out of galvanised iron or steel all as shown on electrical plate No. 5 of SSR Part-I connected to main board/distribution board Excavation and earth work or drilling hole for electrode., P.C.C. pit and C.I. cover 3.15mm thick .(c) Funnel with watering pipe, wire mesh and copper lugs etc, 40mm G.I. Protection pipe of size ordered specified for protection of earthing lead from mechanical injury or tempering complete including terminal block made of gun metal or phosporous bronze 75x75x25mm drilled and screwed including 3 Nos 8mm dia 25mm long hexagonal head screw all as specified and directed. Complete all as specified and directed.

Supply,laying,testing and commissioning of 70 sqmm 3.5 Core LT XLPE insulated, sheathed, armoured heavy duty electric aluminium conductor cable 1100 Volts grade of size as specified below (laid in trenches, ducts, pole, wall etc.) including taking out old unserviceable LT cable from trenches/pole/ducts etc. complete all as specified and as directed by Engineer in Charge. Note : (i). Necessary test results like continuity test, megger tests, shall be submitted to Engineer-in-Charge before the cable is laid. (ii). Excavation earth work will be measured and paid separately. Make: Havells/ Legrand/ L&T

M & L pulvarised stone dust as in sand cushoning for UG cable complete and directed by Engineer-in-charge.

M & L for precast cement concrete cable cover cast as site in cement concrete (1: 1½: 3)type A1 LV type using 20 mm grade aggregate cable cover of size 250x 150x40 mm laid along alignment of cable as protectionto cable over sand cushioning in trenches all as specified and directed.

Dismantling and taking up old unserviceable GI water mains with fittings from trenches, floors,and walls etc. of the following sizes complete, all as specified and directed.

100mm bore

50mm bore

25mm bore

20mm bore

15mm bore

Supply and Laying of GI tubing medium grade with all fittings such as bends, sockets, elbows, tees, reducers, unions, sockets complete laid in trenches/ floors or fixed to walls all as specified. [Make: Jindal/ Prakash/ Tata/ Zenith]

100mm bore

80mm bore

50mm bore

40mm bore

25mm bore

20mm bore

15mm bore

Taking up old unserviceable gun metal gate valve with iron wheel head screwed and M & L for new gun metal gate valve with ISI mark and iron wheel head screwed in both ends for GI pipes for the following sizes.(Make : ZOLOTO/ LAKSHMI/MITTAL )

50mm bore

40mm bore

25mm bore

20mm bore

M & L for carrying out repairs to existing sluice valve chamber of inner size up to and including 0.9m x 0.9m x 0.6. complete by removing small plants, bushes from inside/out side the valve chambers, cleaning internal/ external wall surfaces, refixing loose valve chamber cover frame by grouting, plastering internal / external walls with cement mortar 1:3 including filling up damaged portion with precast cement concrete solid block masonry 1:3:6 type C1 in cement mortar 1:4 complete all as directed.

Taking out old unserviceable CI sluice valve complete including fittings and S & F for sluice valve class PN 1.6 both end flanged with gasket washer, nuts, bolts & brass spindle & check nuts etc for seawater pipe line heavy duty of the following sizes. ( Make : HAZRA/VENUS/UPADHAYA )

80mm bore

100mm bore

Dismandling and taking up old unserviceable / serviceable water storage tank of capacity 500/750ltrs removing to E/M store or taken as credit

S & F rotational moulded polyethylene water storage tank 3 layered of capacity 1000 ltrs (Cylindrical vertical with closed top) with 25 mm GI medium grade pipe for inlet, outlet, over flow, check nuts for inlet and outlet, hoisted and fixed in position all as specified.(Make : SINTEX/ Polycon)

Taking out unserviceable ball valve from existing inlet pipe line and S & F new ball valve complete with polythene float, fly nut for GI Pipe connection including necessary GI fittings such as elbow, nipple etc of size 25 mm dia bore complete all as specified. (Make : PRAYAG)

Kathir Marketing Services

SACKSON ENTERPRISES

M/s SHIVA BUILDERS

Sree Tirumala Enterprises

NAWAZ CONSTRUCTIONS

STANDARD AGENCIES

M/s Sriya Enterprises