Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | SINGLE₹30.1 CrAccepted-Finance 84 M BLOCK COMMERCIAL GREATER KAILASH DELHI DELHI 110048 | SOUTH DELHI | DELHI | 110048 | ₹30.1 Cr | SINGLE | Accepted-Finance ok |
| 2 | Rejected-Technical | - | - | Rejected-Technical Non-Responsive |
Tender Value
₹28.9 Cr
EMD Value
₹28.9 L
Closing Date
28 Feb 2024, 5:00 pmClosed
Administrator, RMC
RMC
Request for Proposal for Setting Up and OandM of Material Recovery Facility Cum Mini Transfer Station MRF Cum MTS and Refuse Derived Fuel RDF in Ranchi Area of Ranchi Municipal Corporation including Operation and Maintenance of desired capacity
2024_UDD_82449_1
89/SANITATION
Open Tender
Miscellaneous Works
670 days
As per NIT and RFP
Please refer Tender documents.
2 documents required · 2 mandatory
₹29,500
₹28.9 L
Ranchi Municipal Corporation
15 Oct 2024
8 Feb 2024
29 Feb 2024
8 Feb 2024
28 Feb 2024
8 Feb 2024
15 Feb 2024
Amount
Construction and Developing MRF &RDF Facility Under Ranchi Municipal Corporation
Earth work in excavation in foundation trenches in ordinary soil (vide classification of soil Item-A) and disposal of excavated earth as obtained to a distance up to 50M. Including all lifts with leveling ramming the foundation trenches removing roots of trees shrubs all complete as per approved design and per building specification and direction of E\I. 150 x 200 mm size
Earth work in back filling the trenches after laying different types and size of pipes with earth removed during excavation within initial lead and lift as per specification and direction of Engineer in charge.
Filling in foundation trenches and plinth in layers not exceeding 150 mm thick well watered, rammed fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50 m and lift of 1.5 m all complete as per building specification and direction of E/I
Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/I. 150 x 200 mm size
Filling in foundation trenches and plinth in layers not exceeding 150 mm thick well watered, rammed, fully compacted and fine dressed with earth obtained after cutting within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I (Mode of measurement compacted volume)
Providing designation 75B one brick flat soiling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of Engineer. 150 x 200 mm size
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering- All work upto plinth level- 1:4:8 (1 cement: 4 coarse sand (zone III): 8 graded stone aggregate 40 mm (nominal size))
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering- All work upto plinth level- 1:2:4 (1 cement: 2 coarse sand (zone III): 4 graded stone aggregate 20 mm (nominal size))
Reinforced Cement Concrete work in walls (any thickness), including attached pilaster, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level excuding the cost of centering, shuttering, finishing and reinforcement: 1:1.5:3( 1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size)Same as above but in superstructure.
Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centring, shuttering, finishing and reinforcement- All work upto plinth level: 1:1.5:3 (1 Cement : 1.5 Coarse Sand (zone - III) : 3 graded stone aggregate 20 mm nominal size)
Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15 degrees landings, balconies, shelves, chajjas, lintel, bands, plain window sills, stair cases, spiral stair cases above plinth level upto floor five level, excluding the cost of centering, huttering, finidshing and reinforcement with 1:1.5:3(1 cement :1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size).
Providing and laying in position reinforced cement concrete of specified grade excluding the cost of centering and shuttering- All work upto plinth level: 1:2:4 ( 1 cement: 2 coarse and (zone 3): 4 graded stone aggregate 20 mm nominal size)
Centering ans shuttering including strutting, propping etc. and removal of form for
Suspended floor , roofs, landings, balconies and access platform
Lintel, Beams, Plinth Beams , girders bressumers and cantilevers.
Foundations, footings, bases of coulmn, etc for mass concrete
Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20mm nominal size).
Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20mm nominal size).
Providing designation 75A brick work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing taxes and royalty all complete as per building specification and direction of E/I.
Providing designation 75A Brick work in C.M (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.
providing designation 125 mm thick reinforced designation 75A brick work in CM (1:40 in supestructure with approved quality of clean coarse sand of FM 2 to 2.5 including the cost of screening, carriage of material, scaffolding raking out joints to 15 mm depth curing taxes and royalty ( but excluding cost of reinforcement)
Providng 12 mm thick cement plaster (1:4) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.
Providng 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.
Providing 6mm thick cement plaster (1:4) in ceiling with celean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.
providing 1.5 mm cement punning including curing , carriage of water with all leads and lifts as per building specification and direction
Labour for fabricating, erecting, hoisting and fixing in position structural steel work in R.S. joists, channels, angles, Tees, flats, plates, lattice members, built up compound sections in columns, girders, staircase, or trusses including cost of gusset plates, holding down bolts, anchor plates at all heights and depths, bolting, welding (machining wherever necessary) with applying a priming coat of red lead paint all complete as per building specification and direction of E/I.
Tack coat On Bituminous surfaces:Providing and applying tack coat with bituminus emulsion pressure distributer at the rate of 0.20 kg per sqm on the prepared bituminious granular surface cleaned with mechanical broom
Excavation for road work in soil with hydraulic excavator including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and tranporting to the embankment location within all lifts and lead upto 1000 m.
Providing and laying in position cement concrete of specified grade excluding the cost of cenetering and shuttering - all work upto plinth level.
Providing designation 75B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I.
Construction of un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with approve grade cement @ 400 kg per cum, coarse and fine aggreagate confirming to IS 383, maximum size of coarse aggreagte not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and logitudinal joints, joint filler, separation memnrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtirs as approved, curing compund, finishing to lines and grades as per drawing
Granular sub base with coarse graded material (400-1) (construction of granular sub base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with front end loader at OMC and compacting with the vibratory roller to achive the desired density, complete as per clause 401.
Wet Mix Macadam (Providing, laying, spreading and compacting graded stone aggregates to WMM specification including premixing the materials with water at OMC in mechanical mix plant carriage of mixed material by tipper to site , laying in uniform layers with paver in sub-base/basecourse on well prepared surface and compacting with vibratory roller to achieve desired density. with vibratory rollar
Providing Tor steel reinforcement of 8mm dia rods as per approved design and drawing excluding carriage of M.S. Rods (straight or in coils) to work site cutting, bending and binding with annealed wire with cost of wire removal of rust, placing the rods in position all complete as per building specification and direction of E/I.
Do ---12 mm dia -- do
Earth work in excavation (As per IS:3114/1965 for laying of different types and sizes of pipes so as to give one meter average cover over the socket of pipe with disposal of excavated earh within nitial lead and lift as per specification and direction of Engineer in charge. 100 x 0.5 x 1.0 M (Classification of soil item-B)
Supply and erection of M S swaged tubular pole conforming to IS: 2713-1980 (part I to II) with galvanised base plate in position including excavation of the pit and filling the same with C.C. of M-20 grade (1:1.5:3) from base plate to 50 cm above ground level, with the help of steel frame not less than 40 cm dia up to 114.3mm outer dia and 50 cm beyond 114.3mm outer dia around the pole. Duly finished with cement plaster, earthing terminals, cable entry, GI cable sleeve complete as required. After eraction pole shall be painted with two coat of red oxide primer and two quote of enamel paint of silver colour as per the direction of Engineer incharge.The pole shall be fabricated by using ISI mark tube for structural purpose of following height & designation. ( See Table P - 02 for specs. ) complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR- 9.0 MTR
Providing & Fixing of IK07 IP 66 protected LED Street Light Luminaire on existing bracket / pole. Fixture made of powder coated single piece pressure die cast aluminum LM6/ ADC12 material with heat dissipation fins on housing with UV stabilized PC/Toughened Glass cover (UV stablzation report submitted for UV cover) and secondary lens on each LED & should be SMD type . The System level Luminaire efficacy >=120 lm/ wt with High Power LEDs is to be used and potted driver must be potted & has a unique BIS R number with Input Voltage AC 120 to 270 V AC with High voltage Cutoff @>=300 V AC and Auto resetting Safety ,Input Frequency 50Hz±3% Power Factor >0.95 driver Efficiency >85% ,THD(I) <10% Humidity 10% to 90% RH Working Temp -5C to 45C . driver current <1000mA shown in LM79 report. The luminaire shall be BIS certified and T.C. certified. Life Expectancy Equal or more than 50000 burning hrs with Minimum 70% lumen maintened ,color Rendering Index >70 and CCT 5700K +355K. Surge protection shall be min ≥ 4 KV internal and min 10 KV external. driver should be Phase to phase protection of 440 V for 4 Hrs. Manufactures Word Mark / Name Engraved/Embossing on die cast housing to allow traceability / authenticity. Fixture shall be AS PER IS 10322 Complianced. OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR LED Street Light fixture 210 Watt
Add for supply and fixing of M S Overhang of following size over the existing poles. Overhang shall be painted with two coat of red oxide primer and two quote of enamel paint of silver colour as per the direction of Engineer incharge All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR 88.9mm OD x 3.25mm thickness Group 2
Providing & Fixing of Normal / High Output High pressure sodium vapour/ Metal halide / Halogen lamp as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .
Supply and fixing of junction box of size 280 X 170 X 130 mm with hinges and locking arrangement & MS clamp made of 50 X 6 mm flat complete in all respect.
Supply and laying of following sizes Al. conductor PVC insulated armoured seathed cable of 1100 V grade at a depth of 750 mm B. G. L (2 core 16 sqmm)
Earthing with G.I. earth plate 600mm X 600mm X 6mm thick including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc (but without charcoal or coke and salt) as required.
Poviding and supplying in standard lengths High Density Polyethylene pipe(HDPE Pipe) 25mm to 500mm dia conforming to IS4984- 4984 / 14151 / 12786 / 13488 (Latest revision with necessary jointing materials like mechanical connector---do--- (HDPE pipe of materials grade PE 100-PN 10(dia in mm)- 110 MM DIA
Providing and fixing soil, waste and vent pipes Sand cast iron S & S Pipe as per IS :1729 (100 mm dia)
Supply and fixing of feeder pillar of M.S cubicla box of size 100 x 75 x 40 cm made from 2 mm M.S sheet using angle of size 40 x 40 x 6 mm duly hinged and locking arrangement, painting two coats of enameled paint over red oxide primer providing aluminium Bus-bar or suitable size with 100 A/415 V TPN rewirable type main swithc with cement concrete foundation providing 1 Mtr GI pipe on 100 mm dia complete in all respects as per direction of E/I.
Supply and making of earth main hole of size 1' x 1' and 2' deep with 1' x 1' CI chamber brick work etc.
Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design : With 20x20 mm square bar
Supply of G.I. Pipes 65 mm dia
Supply of G.I. Pipes 32mm dia
Supply of G.I. Pipes 15mm dia
Laying of G.I. Pipes of approved make in trenches with red lead and yarn with socket and screw joints and cutting pipes to sizes and threading ends where necessary etc. all complete as per specification and direction of Engineer in charge 32mm dia
Laying of G.I. Pipes of approved make in trenches with red lead and yarn with socket and screw joints and cutting pipes to sizes and threading ends where necessary etc. all complete as per specification and direction of Engineer in charge 15mm dia
Providing and fixing gun metel full way valve of approved quality, all complete as per specificaion and direction of E/I. 50 mm dia. And wt not less than 1.5 kg
Providing and fixing gun metel full way valve of approved quality, all complete as per specificaion and direction of E/I. 32 mm dia. And wt not less then 700 gms
Providing and laying 80 mm dia G.I. pipes complete with GI fittings including trenching and refilling
Making connection of GI distribution branch with GI main branch of following sizes by providing and fixing tee, including cutting and threading pipe etc complete (50 to 80 mm nominal bore)
Providing and fixing C.I. Sluice Valve as per I.S.14846 with cap, bolts, nuts, rubber etc. complete, IVC or Kirloskar make. (100 mm dia Class I)
Providing and fixing C.P. brass bib cock of approved quality conforming to IS : 8931.(15 mm dia.)
Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge
Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, reparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level.400 mm dia
Providing and fixing C.I. Double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (the tail pieces, tapers etc. if required will be paid separately). (50 mm dia.)
Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.100 mm nominal size dia
Providing and laying rectified Glazed Ceramic floor tiles 300 x 300 mm or more (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours White, lvory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including grouting the joints with white cement and matching pigment etc., complete.
Providing and laying hydraulically machiine pressed terrazo tilles 20mm thick of approved texture with down marble chips of approved shade, size and quality, laid on 19mm, thick bed of lime mortar (1:1:1) (lime: surkhi: sand) with neat cement slurry mixed with pigment to match the shade of tiles between joints, including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, roualty and taxes all complete as per building specification and direction of E/I. any light colour with white cement
Providing and laying hydraulically machiine pressed terrazo tilles 20 mm thick in skirting of approved texture with 4 mm down marble chips of approved shade, size and quality, over 12mm thick cement palster (1:3) base with neat cement slurry mixed with pigment to match the shade of tiles between joints, including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, roualty and taxes all complete as per building specification and direction of E/I. Any Light with 100% white cement
Providing and laying 6mm precast white glazed tiles in walls over 12mm, cement mortar (1:3) and jointed with gray cement slurry, flush pointed with white cement including rubbing, polishing and cost of curing, taxed and royalty all complete as per building specification and direction of E/I.
Providing and laying 25mm thick kotah stone in risers of steps, skirting and pillars of approves size, texture and colour laid over 12mm thick cement palster (1:3) base with neat cement slurry mixed with pigment to match the shade of tiles between joints, including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, roualty and taxes all complete as per building specification and direction of E/I.
Providing two coats of dry distemper of approved shade and make over a primer coat of washing over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper applying putty wherever required, scaffolding washing floors and taxes all complete as per building specification and direction of E/I.
White washing three coats over new surface in ceiling.
Providing two coat of snowcem of approved shade and make over a coat of cement of primer on new surface mcluding preparing the plastered surface smooth with sand paper, soaping, curing and taxes all complete as per building specification and direction of E/I.
Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cemnt: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) over 75 mm bed of dry brick ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth.
Providing and fixing on wall face unplasticised - Rigid PVC rain water pipes conforming to IS : 13592 Type A. 110 mm dia
Providing and fixing on wall face unplasticised - PVC moulded fittings / accessories for unplasticised - Rigid PVC rain water pipes conforming to IS : 13592 Type A. 110 mm shoe.
Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter.
Supplying fitting and fixing oxidised iron fittings of approved quality and make to doors and windows all complete as per building specification and direction of EI 100 mm butt hinge
Supplying fitting and fixing 35mm thick solid core type non-decorative single leaf flush shutters in doors and windows with black board core blended with high quality phenol formal dehyde synthetic resin both side commercial veneered of standard make with oxidised iron fittings hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/I.
Supplying, fitting and fixing fully glaxed steel door, windows or ventilations of standard rolled 'T' and mullion steel sectioons and size as per IS-1038 joints met and welded with 100x16x3mm M.S. lugs fixed in cement concrete (1:2:4) blocks 15x10x10cm, size including cost of oxidised iron fittings, with hinges, handle per steps, catch springs, 3mm thick palin glass panes with Aluminimum beads and inner frame fixed with lugs with 20mm long 6.3mm G.I. counter sunk machine screw and nuts and applying a coat of red lead paint carriage to work site hoisting and placing in position in all storys and taxes all complete as per building specification and direction of E/I.
Providing and fixing fan hook of 16mm dia M.S. bar 1 metre long bent to required size and shape placed in position and fixed in R.C.C. slab/ beam at the time of casting all complete as per building specification and direction of E/I.
S/P/F good quality well dressed and well seasoned sal wood work in chaukhats in doors, windows opening…. Including wedge over all clamps complete including application of two coats of wood preservative of approved quality on the surface facing wall and lintal all complete as per building specification and direction of Engineer in Charge
Providing french spirit polishing over new wooden surface to give desired texture and gloss with approved make and shade of ready mixed french polish including preparing the surface after cleaning, removing dirt scales, smokes, grease and sand papering, including cost of scaffolding and taxes all complete as per building specification and direction of E/I.
Supplying, fitting and fixing vitreous white glazed earthen ware I.W.C of parry Hindustan or any other ISS approved make with 100mm H.C.I 'P' trap 15 litres C.I pull and let go flushing cistern of names or other I.S.S equivalent make, complete with all fittings, C.I. or CC brackets 32mm alkathene/PVC telesopic flush, pipe about 2M long with one brasscoupling and clamps G.I. chain and pull including supplying and fixing a pair of vitreous white glazed earthenware ware footrest to be fixed in floor 15mm C.I. body brass spindle stope cock of weight not less than 50gm, 15mm PVC connection pipe 450mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/I. 510 mm long with 12.5 lit low level CI cistern
Supplying, fitting and fixing flat back or angular, lipped front vitreous white glazed earthen ware urinal of 'Hindustan "Parry" or any other approved ISS make with 5 liters capacity C.I automatic fulsiing cistern of reliance for any other ISS approved make with all fittings with CI or RS brackets, standare size GI flush pipe with fitting clamps, 15mm C.I. brass spindle stop cock of approved quality weight not less than 400gm, 15mm PVC / Alkthene pipe 450mm longwith brass coupling at both ends and doing plumber joints including painting of exposed part with two coats of approved paintover a priming coat of red oxide, cutting wall and floor, making good the same etc. all complete as per specification and direction of E/I.
Supplying, fitting and fixing vitreous white glazed earthen ware wah hand basin of parry or Hindustan or any other ISS approved make supported on painted C.I. or R.S. brackets 32mm C.I. brass waste, 15mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350 gm, 32mm PVC waste pipe 750mm long wtih brass coupling at one end and making plumber joints etc. all complete as per specification and as per direction of E/I.
Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
Providing and fixing 600 x 450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
Providing and fixing M.S holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10 x 10 x 10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone sggregate 20 mm nominal size) including cost of cutting holes and making good the walls etc. (100 mm dia Pipe)
Solar Powered Road Marker (Solar stud) Supplying of Solar Raised Pavement Markers made of polycarbonate molded body with circular shape, solar powered, LED self illumination in active mode 360 degree illumination and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face in passive mode.The marker shall support a load of 20000 kg tested in accordance to ASTM D 4280. The marker should be resistant to dust and water ingress according to IP 65 standards and should withstand temperatures in the range of 0 C to 70 C. Color of lighting could be provided in red or yellow (amber) as per requirement and typical frequency of blinkikng in 1 Hz.There should be current losses of less than 20 microamperes at 2.4 V in sleepcharging mode to enhace the life of the marker and a full charge should provide for a minimum autonomy of 50 hours.The height, width and length of the marker shall not be less than 10mm x 100mm x 100 mm. Also, the surface diameter of the marker shall not be less than 100 mm respectively.The weight of the marker shall not exceed 0.5 Kilograms.Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive and complete as directed by the engineer.
Providing and fixing of Retro reflectorised cautionary mandatory and informatory sign as per IRC:67 made of encapsulated leas type reflective sheeting vide vide clause 801.3, fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75mmX 75 mmX6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm X45 cmX60 cm, 60 cm below ground level as per approved drawing.60 cm equilateral triangle
Providing and fixing of Retro reflectorised cautionary mandatory and informatory sign as per IRC:67 made of encapsulated leas type reflective sheeting vide vide clause 801.3, fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75mmX 75 mmX6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm X45 cmX60 cm, 60 cm below ground level as per approved drawing.60X45 cm rectangular
Case-(ii):Type B: Providing and laying of premix sand seal coat with HMP of appropriate capacity not less than 200 tonnes / hours using crushed stone chipping 6.7mm size and penetration bitumen of suitable grade
Prime coat, providing and applying primer coat with SS1 grade bitumen emulsion on prepared surface granular base including cleaning of road surface and spraying primer coat at the rate of 0.7 kg/sqm using mechanical means.
Bituminous concrete Grading II with VG-30 grade Packed Bitumen- Providing and laying bituminous concrete with higher capacity batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder @5.4 percent of mix and filter, transporting the hot mix to work site, laying with a hyrostatic pavor finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to acheive the desired compaction as per MORTH&H specification clause no 507 complete in all respects
Dense Graded Bituminous Macadam Grading-II with VG-30 grade packed Bitumen- Providing and Laiyng dense graded bituminous macadam with higher capacity batch tyoe HMO using crushed aggregates of specified grading, premixed with bituminious binder @4.5 percent by weight of total mix and filler, transporting the hot mix to work site laying with a hydrostatic paver finisher with sensor control to the required grade level and alignment, rolling with smotth wheeled, vibratory and tandem rollers to acheive the desired compaction as per MORTH&H speification clause no 505 complete in all respects
Painting lines, dashes,arrows etc on roads in Two Coats On New Work (painting lines, dashes arrow ete on roads in two coats on new work with ready mix road marking paint confirming to IS :164 bituminious surface including cleaning the surface of all dirt dust and other forigen matter demarcation at site and traffic control. Upto 10 cm in width.
Providing and fixing G.I.pipes complete with G.I.fittings and clamps,including cutting and making good the walls etc. (Internal work): Concealed pipe including painting with anti corrosive bitumastic paint,cutting chases and making good the wall. (15 mm dia nominal bore)
Providing and fixing G.I.pipes complete with G.I.fittings and clamps,including cutting and making good the walls etc. (Internal work): Concealed pipe including painting with anti corrosive bitumastic paint,cutting chases and making good the wall. (20 mm dia nominal bore)
Supplying tools and making connection of new G.I. distribution branch 15 mm to 50 mm dia with existing G.I. main by providing and fixing G.I. Tee including cutting of pipe at two places and threading their ends, providing long screw and one G.I. Nipple, all complete as per specification and direction of E/I. : 50 mm dia pipe
Providing and fixing brass/C.I. Stop cock of approved quality all complete as per specification and direction of E/I. 15 mm dia pipe
Providing and fixing male ended 15 mm dia brass bib cock of approved quality (Wt. not less than 350 gms.) with extra socket all complete as per specification and direction of E/I.
Providing and fixing PTMT soap Dish Holder having length of 138 mm, breadth 102mm, height of 75mm with concealed fitting arrangements. Weighing not less than 106 gms.
Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
S/F/F MS grill gate with MS grill made of 20X6 MS flats or 16 mm square bars fitted on ---- do ---E/I In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works Entry gate 4M wide and 1.5M height
Providing two coats of synthetic enamel paint of approved shade and made over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direction of E/I.
Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer?in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
Providing ridges or hips of width 60cm over all width plain G.S. sheet fixed with polymer coated J. or L hooks, bolts and nuts 8 mm dia. G.I. limpet and bitumen washers complete
Providing and fixing 15 cm wide 45 cm over all semicircular plain G.S sheet gutter with iron brackets 40 x 3 mm size, bolts, nuts and washers etc. including making necessary connections with rain water pipes complete. 0.8 mm thick with zinc coating not less than 275 gm/Sqm.
Wiring for light point/fan point/ exhaust fan point/ call bell point with 1.5 sq. mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq. mm FR PVC insulated copper conductor single core cable etc as required. (Group A)
Wiring for light point/fan point/ exhaust fan point/ call bell point with 1.5 sq. mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq. mm FR PVC insulated copper conductor single core cable etc as required. (Group B)
Wiring for light point/fan point/ exhaust fan point/ call bell point with 1.5 sq. mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq. mm FR PVC insulated copper conductor single core cable etc as required. (Group C)
Wiring for light/ power plug with 2 x 4 sq.mm FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, along with 1 No 4 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required
Wiring for light/ power plug with 4 X 4 sq. mm FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit alongwith 2 No 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.
Supplying and fixing of following sizes of PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. (25 mm)
Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc as required. (75x75x50mm)
Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc as required. (147x93x47mm)
supply and fixing following modular base & cover plate on existing modular metal boxes etc as required. 4/5 module
Supply and fixing following modular switch and socket on the existing modular plate & switch box including connections but excluding modular plate etc as required (3 pin 5/6 amp socket outlet)
Supply and fixing following modular switch and socket on the existing modular plate & switch box including connections but excluding modular plate etc as required (Telephone socket outlet)
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection, painting etc as required
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 15/16 amps modular socket outlet and 15/16 amps modular switch, connection, painting etc as required
supply and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc as required
Supply and fixing call bell/ buzzer suitable for D.C/ A.C single phase 230 volts complete as required.
Supply and fixing 2 pin, 5 amp. Ceiling rose on the existing junction box/ wooden block including connection etc as required.
Supply and fixing brass batten/ angle holder including including connection etc as required
Installation, testing and comissioning of ceiling fan, ancluding wiring the down rods of standard length(upto 30 cm) with 1.5sq mm FR PVC insulated, copper conductor single core cable, including providing and fixing phenolic laminated sheet cover on fan box etc as required
Installation , testing and commissioning of pre-wired, flourescent fitting/compact flourescent fitting of all types, comlete with all accessories and tube etc directly on ceiling/wall, including connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc as required.
Installation , testing and commissioning of pre-wired, flourescent fitting/compact flouredcent fitting of all types, comlete with all accessories and tube etc. including supplying and fixing ball and socket arrangement 2no down rods of 20mm dia X 1.6mm thick steel conduit upto 30cm lenth painting and wiring the down rods and connection with 1.5 sq mm FR PVC insulated, copper conductor, single core cable and earthing etc as required.
Installation of exhaust fan upto 510 mm sweep in the existing opening including making the hole to suit the size of the above fan making good the damage connection testing commissioning etc as required.
Supply and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc as required. 2 way single door
Supply and fixing 6 amps to 32 amps rating 240 volts 'B' series miniature circuit breaker suitable for lighting and other loads of following poles in the exsisting MCB DB complete with connection testing and commisssioning etc. as required 6/32 amps, single pole B series
Providing and fixing 4 mm dia copper wire on surface or in recess for loop earthing as required
Supply and laying of 3.5 x 35 mm2 Al. armoured table from D.G terminal to D.G pannel and from D.G pannel to LT pannel.
Silent type D.G. set of capacity 25 KVA three phase with AMF Panel IS/ IES- 60034-1 IS: 1460 IS: 13018
Silent type D.G. set of capacity 125 KVA three phase with AMF Panel IS/ IES- 60034-1 IS: 1460 IS: 13018
Supply and laying of 3.5 x 120 mm2 Al. armoured table from D.G terminal to D.G pannel and from D.G pannel to LT pannel.
ABC' Make or any other reputed make manufacturers with ISO:9001approved 315 KVA tansformers 11KV/433V copper wound 3 phase oil cooled type conforming to ISO:2026 with first filling of oil per IS:335 and standard fitting and accessories.
Copper Earth Plate Electrode :- Earthing with copper earth plate 600 mm x 600 mm x 3mm thick including accessories and providing masonary enclosure with cover plate having locking araangement and watering pipe etc required . (but without charcoal or coke and salt)
Providing random rubble stone masonry in C.M. (1:6) in foundation and plinth with hammer dressed stone of less than 0.03 M3 in volume and clean coarse sand of F.M. 2 to 2.5 including cost of screening, raking out joints to 20mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.
1:3:6 (1 Cement :3 Coarse Sand (zone - III) : 6 graded stone aggregate 40mm nominal size)
Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1:3 (1 cement:1.5 coarse sand(zone-III): 3 graded stone aggregate 20 mm nominal size).
1:1.5:3 (1 cement: 1.5 coarse sand (zone III): 3 graded stone aggregate 20 mm (nominal size))
Steel reinforcement for RCC work including straightening, cutting, bending, placing in position and binding complete (Hard drawn steel wire)
Making soak pit 2.5 m diameter 3.00 m deep with 45 X 45 cm dry brick honey comb shaft with bricks and SW drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay FPS (non moduler) brick of class designation 75
Providing designation 75A brick work in C.M.(1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10 mm thick mortar joints, cost of screening, materials, scaffolding, raking out joints to 15 m depth, curing taxes and royalty all complete as per building specification and direction of E/I.
Supplying, Fitting and fixing M.S. Gril Gate with M.S. grills made of 20x6 mm M.S. flats or 16 mm M.S. square bars fitted on 25x25x6 mm. M.S. Angle frame -do- (when steel is not supplied by the deptt) (Entry gate 4 M wide and 1.5 M height)
Providing and laying Double charge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and confirming to IS: 15622/ISO 13006 of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement:4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigments etc., complte. Size of tile 600 X 600 mm
Providing and fixing in position pre-cast RCC manhole cover and frame of required shape and approved qrality . HD 20 (Circular shape 560 mm internal dia.)
Providing and Fixing soil ,waste and vent pipe: 75 mm dia sand cast iron socket & spigot pipe
Extra for Providing and fixing 30x4mm glass strips in joints of flooring, complete job as per specifications and direction of E/I.
Cetering ans shuttering including strutting, propping etc. and removal of form for Shelves cast in situ
Providing and fixing 15 cm wide 45 cm over all semicircular plain G.S sheet gutter with iron brackets 40 x 3 mm size, bolts, nuts and washers etc. including making necessary connections with rain water pipes complete. 0.8 mm thick with zinc coating not less than 275 gm/Sqm.
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering-All work up to plinth level. 1:3:6 (1 cement: 3 coarse sand zone-III : 6 graded stone aggregate 20 mm nominal size)
Providing designation 75B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I.
Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 MM dia
Providing and fixing unplasticised-PVC pipe clips of approved design to unplasticised-PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with MS screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm
Laying of G.I. Pipes of approved make in trenches with red lead and yarn with socket and screw joints and cutting pipes to sizes and threading ends where necessary etc. all complete as per specification and direction of Engineer in charge. 65 mm dia
Laying of G.I. Pipes of approved make in trenches with red lead and yarn with socket and screw joints and cutting pipes to sizes and threading ends where necessary etc. all complete as per specification and direction of Engineer in charge. 50mm dia
Construction of 200X165 mm diaX180 M deep High Yield Drilled Tube Well with mechanical Rotary Rig Machine with 2000 mm NB dia UPVC blue casing pipes along with supply and installation of single phase submersible motor pump set
Estimate for construction of high yield tube well (HYDT) of 200 mmX 150 mm X 125m deep bore well by hydraulic rig machine with MS casing pipe (model estimate attached) with submersible pump etc
Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying: a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured.
Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.
Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).
Providing and laying S&S centrifugally cast (spun) iron pipes (Class LA) conforming to IS - 1536 : 100 mm
Providing lead caulked joints to spun iron or C.I. pipes and specials, including testing of joints but excluding the cost of pig lead :100 mm
Uprooting rank vegetation and weeds by digging the area to a depth of 60 cm, removing all weeds and other growth with roots by forking repeatedly,breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of all rubbish with all leads and lifts
Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately
Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment
Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water) Trees Plant
Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water) Shrubs Plant
Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water) Hedge Plant /Ground cover
Providing and fixing pre-cast RCC manhole cover and frame of required shape and approved quality.Circular shape 500 mm internal dia.(MD-10)
G.I Barbed Wire Fencing 1.8 metre High (Providing and fixing 1.8 metres high GI barbed wire fencing with 2.4 m angle iron posts 50 mm x 50 mm x 6mm placed every 3 metres centre to centre founded in M15 grade cement concrete, 0.6 metre below ground level, every 15th post, but last one end post and corner post shall be strutted on both sides and the end post on one side only and provided with 12 horizontal lines and 2 diagonals interwoven with horizontal wires, fixed with GI staples, turn buckles etc complte as per clause 808
Construction of Embankment with material deposited from roadway cutting: construction of emabankment with approved material deposited at site from Roadway cutting and excavation from drain and faundation of other structure graded and compacted to meet requirements of Table 300-2. Rate per cum aftr adding royalty @ Rs. 27.48/ cum
Existing Boundary Wall
4.5 kg capacity extinguisher CO2 type.
FH Tee
FH Post
Brass Nozzle (Branch pipe)
Male & Female couplings
Rubber hose pipe 65 mm dia in 30m length
Feeding Conveyor to Trommel (800 mm wide)
Magnetic Seperator
Trommel 80mm
Discharge conveyors from Trommel to +80 (600 mm wide)
Discharge conveyors from Trommel to -80 (600 mm wide)
Feeding conveyors from Trommel to Manual Sorting Conveyor (600 mm wide)
Manual Sorting Conveyor (1000 mm wide)
Blower 2.0 HP
Bailing Press for Plastic
Skip Bins
Feeder Conveyor 1 (1.2 m x 16.00 m)
Magnetic Seperator
Trommel 10 mm
Belt Conveyor 2 - Reject 1 (0.8 m x 11.00 m)
Belt Conveyor 3 Trommal to P. Shredder (1.0 m x 7.00 m)
Shreedder 1 (25 TPH)
Belt Conveyor 5 - P. Shredder to ADS (1.0 m x 22.00 m)
Air Density Seperator with air Lock
Cyclone with air lock
Belt Conveyor 3 - ADS reject (0.8 m x 7.00 m)
Belt Conveyor 4 - ADS to S. Shredder (1.0 m x 7.00 m)
Shredder 2 (20 TPH)
Belt Conveyor 6 - S. Shredder to storage (0.8 m x 7.00 m)
Discharge conveyors from Trommel to +80 (600 mm wide)
Discharge conveyors from Trommel to -80 (600 mm wide)
Weighbridge 30 tonnes Capacity
Sub Panel for Electricity Connection of Machines
Front End Loader
Vehicle Washing Platform
Sub Panel for Electricity Connection of Machines
LT panel having one no incoming panel, 5 nos, outgoing panel and one number change over switch for DG set.
Supply and installation of electronic weigh bridge machine of approved make and specification of 20 ton capacity including all equpment machinery, mechanical, electrical, instrumentation, all civil work as also hookup with computers performance testing supply of spare parts for startup, commissioning including all labs, materials the complete with all taxes.
CCTV Camera
VGA Cabel- 50 meter
Bayonet Neill Concelman Connectors
17 Inch Monitor
Tenda Router
Cat 6 Wire (50 mt)
Wire D link
Wire Clip
Camera Box
Installation Charge
ID Card Scanner & Reader
Portable Compactor
Carriage of Construction Material
Add GST @ 18%
Add Labour Cess @ 1%
Tipping Fee During Operation and Maintenance Period of Material Recovery Facility & Refuse Derived Fuel Facility including revenue
Waste Quanty for 1 Years
stage.html
html • 0.03 MB
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid