50/EEC/BSNL/CD/BGL/2024-2025

Amount

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc., up to floor five level, excluding the cost of centering, shuttering and finishing :

1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer’s specification.

Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets :

20 mm dia (heavy type)

Providing and fixing 50 mm bright finished brass cup board or wardrobe knob of approved quality with necessary screws.

Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete.

Double strip (horizontal type)

Providing and fixing cup board shutters 25mm thick, with Pre-laminated flat pressed three layer particle board or graded wood particle board IS: 12823 marked exterior grade (Grade l Type ll) having one side decorative lamination and other side balancing lamination including IInd class teak wood lipping of 25mm wide x12 mm thick with necessary screws and bright finished stainless steel piano hinges complete as per direction of the Engineer-in-Charge

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

12 mm cement plaster of mix :

1:6 (1 cement: 6 fine sand)

12 mm cement plaster finished with a floating coat of neat cement of mix :

1:3 (1 cement: 3 fine sand)

Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement.

12 mm cement plaster

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer, of required shade and colour all complete :

New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre

Distempering with 1st quality acrylic distemper (ready mixed) having VOC (Volatile Organic Compound ) content less than 50 gram/ litre, of approved brand and of required shade and colour complete to give and even shade.

Old work (one or more coats)

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.

With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre.

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :

One or more coats on old work.

French spirit polishing :

One or more coats on old work.

Finishing walls with Acrylic Smooth exterior paint of required shade :

Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface).

Old work (One or more coat applied @ 0.90 ltr/10 sqm).

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-harge.

With cement mortar 1:4 (1 cement : 4 fine sand).

Demolishing lime concrete manually/ by mechanical means and disposal of material within 50 metres lead as per direction of Engineer in-charge

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.

Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.

For thickness of tiles 10 mm to 25 mm

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:

White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls and floors wherever required :

W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:

White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Flexible pipe

32 mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Exposed on wall

25 mm nominal outer dia .Pipes.

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :

25 to 40 mm nominal bore

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931:

15 mm nominal bore.

Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour.

15 mm nominal bore with 45 cm length.

Cutting holes up to 30x30 cm in walls including making good the same:

With common burnt clay F.P.S. (non modular) bricks.

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making necessary channels for the drain etc. complete :

For pipes 100 to 250 mm diameter

P/F PVC MULTI FLOOR TRAPS of approved brand and manufacture; 110mmx75 mm including breaking open and removing the damaged floor trap and making good the same with white cement all complete as directed by Engineer-in-Charge.

P/F PVC SWR grade pipes of approved brand and manufacture (FOR MAINTENANCE WORKS) including fixing it in position using solvent or cement mortar ,all complete as directed by Engineer-in-Charge.

75mm dia

110mm dia

Providing and filling light weight cinder in sunken portions etc. complete as per directions of E-I-C (Nominal size 20mm).

Providing and laying Ceramic matfinish floor tiles 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red, Brown laid on 20 mm thick CementMortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cementand matching pigment etc., complete. as directed by the Engineer in charge.

Removing and refixing the PVC door shutter after removing the dmaged hinges and fixinf with new butt hinges etc complete as directed by the Engieer in charge.

Providing and fixing stainless steel jali with or without hole for waste pipe for covering existing floor/nahani trap (a)100mm dia.

Providing and fixing 15 mm Heath faucet of C.P brass head and P.V.C connection pipeof approved make etc. complete as per the directions of Engineer-in-Charge. Cost includes removal of non-funtional/worn-out health faucet.

Providing and fixing two in one tap including fittings of approved make etc. complete as per the directions of Engineer-in-Charge.Cost includes removal of non-funtional/worn-out 2 -in- 1 tap.

Removing and refixing of wash basin for maintenance and repair works including fixing brackets, screws etc. complete as per the direction of Engineer-in-charge.

Providing and fixing mosquito proof mesh of approved make, netlon or equivalent with necessary velcro and fixing to the existing frame with necessary adhesive,screws all complete as directed by Engineer-in-Charge.

Providing necessary repairs to damaged cupboard shutters s by removing the door after removing the bent hinges and refixing the same in poriginal position after necessary repairs to the panels so as to ensure easy operations with necessary replacement of 16 crank regular closing mild steel nickel coated 34x22" cabinet hinges as required, all complete as per the directions of Engineer in charge.( Note: The approximate door areas to be repaired shall be upto 1 sqm).

Providing necessary repairs to the damaged MS windows/doors by removing the door shitter (either by cutting/ burning the hinges using gas welding machine at site or by removing the shutter after removing the screws and butt hinges as the case may be) and refixing the door in original position after removing the bend/ undulations in the door (members either horizontal or vertical or replacing the member it self (if required) including making good the damaged portion with necessary enamel painting (two or more coats over a coat of steel primer) all complete as per the directions of Engineer in charge. Note: The approximate door area to be repaired shall be 2.5sqm (2) The cost of MS sections if used shall be paid separately(A) Window Shutters upto 1.5 Sqm area

Providing & Fixing SWR grade fittings of approved make and manufacture

75MM DIA BENDS with acess door

110MM DIA BENDS with access door

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

P/F SWR grade fittings of approved make and manufacture in the existing line including cutting and fixing with adhesive etc complete as directed by the Engineer in charge.

75MM DIA BENDS

110 dia bend

Arresting leakage in walls by applying brush bond or equivanet over the plastered surface etc complete as per directions of the Engineer-in-charge.

Applying Dr.fixit epoxy bonding agent or equivalent on reinforcements and patchy portion of plastered surfaces by mixing base and hardner to throughly until getting the uniform colour and consistency of the mixed material etc complete as directed by the Engineer in charge.

Applying Dr. Fixit Pidifin 2K or equivalent on plastered surfaces as per the given procedure. 1 .Cleaning the surface throughly such that it shuld be free rom all paint,oil, grease, wax, dirt or any other form of foreign matter which might effect adhesion and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches and washed off with water 2.Mix slowly add Powder part 2kg to Liquid part 1 litre in a clean container until a smooth and homogenous slurry mixture is achieved.Allow the mixed slurry to stand for 5-10 minutes for releasing air-trapped during the mixing prior to application. Mixing material must be use within recommend pot life and no water should be added. 3. The surface should be prewetted throughly before application and surface should be brought to touch dry state. apply the frist coat with stiff nylon brush.Allow the slurry to cure for at least 1 hour before applying a second coat. second coat should be applied in a perpandicular direction to the first coat. etc complete as directed by the engineer in charge.

Providing necessary repairs to the damaged MS gate by removing the shutter (either by cutting/ burning the hinges using gas welding machine at site or by removing the shutter after removing the screws and butt hinges as the case may be) and refixing the door in original position after removing the bend/ undulations in the door (members either horizontal or vertical or replacing the member it self (if required) including making good the damaged portion with necessary enamel painting (two or more coats over a coat of steel primer) all complete as per the directions of Engineer in charge.

MS Gate(Note: The approximate door area to be repaired shall be 4sqm (2) The cost of MS sections if used shall be paid separately )

Uprooting the vegetation growth in the balcny slab by dismantling the cracks, raking out the joints,removing the roots and dipoal of the same etc complete as directd by the Engineer in charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand(zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)