CWE/P-68/2019-20 SPECIAL REPAIR TO BLDG NO NP 89 AND NP 90 OF GOVT MD ACCN AT BHADURIYA COPMPLEX UNDER GE SOUTH PATHANKOT

Amount

M & L Demolition of cement concrete in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete al as specified and directed

M&L for 75mm thick PCC 1:3:6 type C-2 using 40mm graded crushed stone aggregates as in plinth protection finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

Dismantling of floor hearth and wall tiling incl cement morter bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L ceramic Non skid coloured tiles 7 to 8mm thick (Square / rectangular) area of each tile exceeding 0.18 Sqm but n.exc 0.38 Sqm, in floors etc set and jointed in neat cemnt slurry and poitned in coloured cement match the colour of tiles including over 15mm thick screed bed in cement mortar 1:4 all as spd complete all as specified and directed.

M & L coloured Glazed ceramic tiles in vertical surfaces 450 x 350 x 6-7mm set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick backing coat in cement mortar 1:4 complete all as specified and directed.

M & L coloured Non Skid ceramic tiles 7 to 8mm thick (square/rectangular) are of each tile exc 0.11 Sqm but n. Exc. 0.18 Sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including over 15mm thick screed bed or bedding layer with Cement Mortar 1:4 complete all as specified and directed.

M&L Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc set in any type of mortar complete all as specified and directed.

M & L 20mm thick Granite (pure black) work (table rubbed and polished) cills, cooking platforms, in steps, jambs, pillars, window- cills and like in cement mortar (1:4) 10mm thick including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed. Note : All Open Edges to be Half rounded.

Taking down chowkat with shutter (without taking off shutter from frame) including hold fast not exceeding 1.5 sqm each complete al as specified and directed

Taking down chowkat with shutter (without taking off shutter from frame) exc 1.5 sqm but n.exc 4 sqm each including hold fast complete all as specified and directed

S&F pressed steel frame for door made out of MS sheet 1.25mm thick of size 125x60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc including filling of concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregate ) back of chowkats complete all as specified and directed

S&F pressed steel frame for door made out of MS sheet 1.25mm thick of size 105x60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc including filling of concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregate ) back of chowkats complete all as specified and directed

M&L Plain framed factory made 35mm thick shutter of 2nd class hard wood rail & style (two panel) with lock rail and panel of 9mm BWP commercial plywood or 12 mm veneered particle board with commercial veneering on both faces , the size of rail and style as per IS 1003 (Part-1) kiln seasoned and pressure treated all as specified.

S&F 35mm thick 2nd class hard wood plain framed factory made glazed and skelton shutters open rebated and prepared to receive glass/ wire gauge etc (without sas bars)edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for secring glass,etc size of members of shuters as specified in SSR Part-I,Section 8, clause 8.24 (a) complete all as specified and directed.

Providing and fixing factory made PVC INTERNAL DOOR FRAME of size 100 mm x45 mm with a wall thickness of 5mm made of extruded 5 mm thick PVC sheet of density 600 Kg/Cum manufactured by an ISO-9001-2008 certified company and by joining 3 nos heat bent PVC sheet sectiones.The inside section of size 90 x 30 mm shall be made from plain colour PVC sheet of 5 mm.The inside section will be covered by sticking two section of size 30 x35 mm and 70 x 45 mm made from from 5 mm thick plaibn PVC sheet.The frame shall be mittered cut at two corners and joined with 4 nos of 150 mm long brackets of 15 mmx 15 mmMS square tube .The two vertical door farme are to be reinforced with 40mm x20mmMS tube of 90 gauge through out the frame.The door frame shall be fixed to the wall using 8/100 mm long MS screws through the frame by using anchor fastners .A minimum of 4 nos of screws to be provided for each vertical member & minimum 2nos for horizontal members etc complete all as specified and directed. of Engineer -in-charge

Providing and fixing 30 mm thick factory made solid panel prelaminated/plain PVC internal door shutter consisting of frame made out of MS Tubes of 19 gauge thickness and size of 40 mm x 20 mm for stiles as well as as top ,lock & bottom rail MS frame shall have a coat of metal primer of approved make and manufacture MS farme shall be covered with heat moulded prelam/plain C channel made from 5 mm thick PVC sheet of density 600 Kg/Cummanufactured by an ISO-9001-2008 certified compony of size 30 thickness ,110 mm width foaming stiles in which 100 mm should be flat & 5 mm should be taper and 5mm thick,135 mm wide pvc sheet for top rail and bottom railin which 125 mm should be fiat 7 5 mm taper on either side of pannel also for lock rail 145 mm sheet ,125 mm should be flat & 5 mm thick tapper on either side.An additional 5 mm thick PVC strip of 20 mm width is to be struck on interior side of the C channel using PVC solvent cement adhesive.Panneling of 10 mm thick prelam PVC sheet to be fitted in the MS frame welded/sealed to stiles and rails with 30 mm wide x 5 mm thick PVC sheet beading on either side and additional 30 mm wide PVC beading as gap insert for top & bottom rail.Door to be fixed with frame with 3 Nos. MS powder coated butt hinges of size 100 mm *25mm*2mmand 50 mm long steel screws drilled suitable to passv through both both the walls of the MS tube.Other hardware of door should be fixed with 25 mm* 8mm size steel screws etc.complete all as specified and directed.of Engineer -in-charge,manufacture Spfn & Drg.

S&F 18/19mm thick prelaminatd particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed

S&F 9 mm thick vennered decorative plywood grade 1 (with BWR resin ) with decorative face veneers on both faces fixed with screws to timber frame work complete all as specified and directed

M&L for continuous (piono) hinges , mild steel bright finish or electro galvanised, width of flaps 30mm (when open) (ISI marked) complete all as specified and directed

M & L hasp and staple of size 100 mm, aluminium anodised, with pin including bolt to hinge plate and fixed with screws.complete all as specified and directed.

S&F small fittings such as bracket of any type door stop and the like articles n. exc 200 cm each of 2nd class hard wood complete all as specified and directed.

S&F aluminium alloy, anodised 300 mm long sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed. complete all as specified and directed.

S&F 100mm long butt hinges medium weight cold rolled ISI marked mild steel. complete all as specified and directed.

S&F 150 mm long aluminium handles , cast type, anodised complete all as specified and directed.

S&F aluminium anodised, 150 mm long barrel tower bolt of extruded section. complete all as specified and directed.

S&F 300 mm long mild steel ordinary rat rail rod paltren mild steel door spring incl roller and roller plate complete. complete all as specified and directed.

M & L Steel window/ventilator factory made, made out of mild steel tubuler frame suitable for double shutter i.e. Glazed and gauged shutter. Glazed shutter made out of tubular section with sash bar and gauged shutter made out of tubular section without sash bar including hinges, tower bolt, handle, including one shop coat of red oxide primer all as per details shown on drg No CEPZ/ID-245/01 and 246/02 sheet ½ & 2/2 complete all as specified and directed.

S&F in Sheet glass ordinary quality 3 mm thick and glazing with oil putty ang glazing clips in squares n. exc 0.50 sqm each pane. complete all as specified and directed.

S&F Galvanised mild steel wire cloth 0.56mm of nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or glvanised wire staples complete all as specified and directed.

S&F framed work such as grills, gratings using square bar with ends of bars shoulder/welded drilling holes for fixing of guard bars complete all as specified and directed.

M&L for preparing the new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L preparing the new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enameled paint over a coat of red oxide primer complete all as specified.

Supply and fix in repair Vitreous China squatting pan orissa pattern size 580 x 440 mm white with integral foot rests including provision of lime concrete bedding, connection to trap and to flushing pipe, anti syphonage pipe etc complete all as specified & directed.

Supply and fix in repair 10 ltrs capacity PVC symphonic action type, flushing cistern, low level, white, with inlet,ball valve, float and handle including brackets, fush pipe of polyethylene of low or high density or PVC. 32 mm dia. complete all as specified and directed.

S&F in repair Vitreous China wash basin, white, flat back, size 630x450mm including waste coupling 32mm dia and 32mm dia waste pipe, brackets etc. complete all as specified and directed by Engr-in-Charge.

S&F PVC connection 15 mm dia with PTMT nuts of length 450 mm. complete all as specified and directed.

Taking up or down GI pipe 15mm bore and connection, including cleaning for refixing or removal unserviceable pipe from the site complete all as specified and directed.

Taking up or down GI pipe 20mm bore and connection, including cleaning for refixing or removal unserviceable pipe from the site complete all as specified and directed.

M&L cutting chases, pinning in brick work for concealed water tubing and making good to facings where required and pointed in cement mortar 1:3. Cutting not exceeding 10cm girth complete all as specified and directed.

S&F 15mm bore GI tubes medium grade galvanized ISI marked with all fittings short pieces and fixed complete all as specified and directed.

S&F 20mm bore GI tubes medium grade galvanized ISI marked with all fittings short pieces and fixed complete all as specified and directed.

S&F in repairs angle valve fancy type cast copper alloy chromium plated with capstan head high pressure screwed both ends for iron pipe or for union bore of pipe 15mm dia (ISI Marked) complete all as specified and directed.

S&F in repairs stop valve concealed fancy type, long shank and cup (ISI marked) brass chromium plated with capstan head screwed both ends for iron pipe or for union bore pipe of 15mm dia complete all as specified and directed.

S&F 20mm bore stop valve cast copper alloy, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron of pipe or for unoins complete all as specified and directed.

S & F in repair brass bib taps cast copper alloy fancy type chromium plated with long shank with capstan head high pressure screwed down screwed for iron pipes of bore 15mm complete all as specified and directed.

S&F in repair Pillar taps,fancy type cast copper alloy, with capstan heads,chromium plated,screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts,screwed for iron pipe and fixed complete all as specified and directed.

S&F brass chromium plated shower rose 75mm size with or without swivel joints incl fixing to steel pipe or union fixed complete all as specified and directed.

S&F chromium plated steel Soap Dish ISI marked fixed with and incl chromium plated screws of as approved complete all as specified and directed by Engr-in-Charge.

S&F Tubular towel rail 20mm dia ‘D’ type 60cm long between flanges brass chromium plated complete all as specified and directed.

Disconecting water tank exceeding 500 Ltrs and n.exc 1000 Ltrs and removing to store complete all as specified and directed.

Supply and fxing rotational moulded polythene water storage tank, white coloured, tripple layer cylindrical vertical with closed top 1000 litre capacity hoisted and fixed in position, including inlet and outlet pipe connections, 20mm dia and 15 mm dia GI pipes medium grade respectively, 20mm GI pipe medium grade over flow pipe 15 cm long wash out with plug and brass ball valve 20mm, high pressure with polyethelyne float and fly nuts complete all as specified and directed.

Dismantling/taking down of cast iron or reinforced concrete or PVC soil waste and drain pipes 75mm or 100mm dia with all fittings complete all as spd & directed.

S&F 100mm bore sand cast, cast iron soil waste and vent pipes ISI marked in any length with or without ears with cement joints fixed to walls complete all as specified and directed.

S&F 100mm bore sand cast, cast iron soil waste and vent pipes ISI marked in any length with or without ears with lead joints laid in floors or in trenches complete all as specified and directed.

S&F 100mm bore cast iron bends any radius diminishing pieces or tapers (larger bore measured) complete all as specified and directed.

S&F Cast iron branch pieces, single ( equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, 100mm bore complete all as specified and directed.

Supply and fxing in repairs, 100 mm dia cast iron 'P' or 'S' trap ISI marked complete all as specified.

S&F 75mm bore sand cast, cast iron soil waste and vent pipes ISI marked in any length with or without ears with cement joints fixed to walls complete all as specified and directed.

S&F 75mm bore sand cast, cast iron soil waste and vent pipes ISI marked in any length with or without ears with lead joints laid in floors or in trenchescomplete all as specified and directed.

S&F 75mm bore cast iron bends any radius diminishing pieces or tapers (larger bore measured) complete all as specified and directed.

S&F Cast iron branch pieces,single ( equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, 75mm bore complete all as specified and directed.

S&F Cast iron floor trap, dia of outlet 75mm with CI grating including jointing to waste pipe fixed in PCC M-15 (nominal mix) complete all as specified and directed.

Extra only over pipe fittings, if fitted with oval access doors, for pipe of 100mm bore complete all as specified and directed.

Extra only over pipe fittings, if fitted with oval access doors, for pipe of 75mm bore complete all as specified and directed.

S&F 50mm bore sand cast, cast iron soil waste and vent pipes ISI marked in any length with or without ears with cement joints fixed to walls complete all as specified and directed.

M&L Cast iron cowl suitable for pipes of 50mm bore complete all as specified and directed.

M&L Stack clamp out of 50mm x 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing of stays to wall or roof for 50mm bore pipe complete all as specified and directed..

M&L Stack clamp out of 50mm x 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing of stays to wall or roof for 100mm bore pipe complete all as specified and directed.

M&L Stack clamp out of 50mm x 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing of stays to wall or roof for 75mm bore pipe complete all as specified and directed.

S&F PVC (SWR) pipes 110 mm bore, drainage pipes single socketed in any length with rubber ring joints fixed to walls. complete all as specified and directed.

S&F PVC (SWR) bends 110 mm bore any radius. complete all as specified and directed.

Taking down cement plaster on brick wall or concrete surfaces of ceilling etc incl racking out joints hacking for key scrubbing down with water etc. complete all as specified & directed.

M&L rendering 15 mm thick on fair faces of brick work or concrete surfaces including fin facia in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified & directed on external surfaces .

M&L rendering 10mm thick on concrete in cement mortar 1:3 in facia or edging of chajjas,ceiling and roof projection making the line in true shape finished even & smooth without using extra cement complete all as specified & directed.

M&L rendering 5mm thick on concrete in cement mortar 1:4 in ceiling and making the line in true shape finished even & smooth without using extra cement complete all as specified & directed.

M&L rendering 10 mm thick on other than fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and smooth with out using extra cement complete all as specified & directed.

M&L for two coats of oil bound distemper to newly plastered surfaces including preparation of surfaces by application of 3mm thick wall care putty complete all as specified and directed by Engr-in-charge.

M&L two coats exterior emulsion paint on newly plastered surface of wall including preparation of surface by 1-2mm thick wall care putty including complete removal of existing treatment complete all as specified and directed.

M&L two coats exterior emulsion paint on old surface of wall including preparation of surface by complete removal of existing treatment and applying 1-2mm thick wall care putty complete all as specified and directed.

M & L for preparation of new plastered surfaces of ceiling and applying three coats of white wash . complete all as specified and directed.

M&L complete removal of existing treatment of wall and providing wall putty 1-2 mm thick incl preparation of surface and applying two coats of oil bound distemper complete all as spd and directed by Engr-in-Charge.

S&F in repair mild steel curtain rod 25mm dia pre-painted synthetic enamel paint of wooden finishes fixed with screws complete all as specified and directed.

S&F in repair wooden (turned, weathered and mitred) brackets of Ist class hard wood pre-polished with French polish and touch wood with cut, hole suitable for 25mm dia rod fixed with screws and gutties in wall complete all as specified and directed.

S&F in repair wooden (turned, weathered and mitred) end caps with ornament and fixed to curtain rod with screws of design/shape complete all as specified and directed.

M&L Providing & Fixing in repair Stainless steel Plate rack 900mm x 600 mm x 200mm deep with plate racks, spoon holders, shelves etc complete all as specified and directed.

S&F steel Sink with drainage board made of stainless steel 1 mm thick with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets of angle iron and connecting union to pipe over all size 915 mm x460 mm and bowl size 410mmx330mmx 160mm complete all as specified and directed.

M&L Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc with and including taking out existing roof treatments, brushing neat cement slurry with 3.0 Kg of cement per sqm and including 10mm thick rendering in Cement mortar 1:4 on fair faces of concrete, finished even and fair to receive treatment on roof complete all as specified and directed.

M&L Providing and laying of water proofing treatment of roof APP (Atactic Polyproplyllen) modified prefabricated five layer 3mm thick water proofing membrane, with non woven polyester mat reinforcement of 160 gsm, weight of membrane @ 3.6 Kg/Sqm over a solvent based bitumen primer, @ 0.3 Ltr Sqm by the same manufacturer conforming to IS:3384-1986 , The membrane shall be laid using bitmun torch.The end lap should be 100 mm and the side lap must be minimum 75 mm the membrane shall be first laid up to the parapet wall junction and then shallbe overlapped with another membrane (flashing) with an overlap covering up to a distance of 300mm. In case parapet height is less than/ up to 500 mm, membrane shall be terminated at the top of parapet.All rain water pipe opening shall be suitably sealed with the APP membrane complete all as specified and directed. (The rate includes for filling cracks in existing roof with cement putty using suitable bonding agent (shalcrate 42) before laying cement plaster)

M& L for Cement concrete type B1 1:2:4 (using 20mm graded crushed stone agg) 75 mm thick as in Sub base of flooring etc finished surface even and smooth without using extra cement complete all as specified and directed.

M&L Screed bed or bedding layer of 20 mm thick in cement mortar (1:6) as in floor, complete all as specified and directed.

M&L Chequered cement concrete coloured, table vibrated chemical coated, tiles 200mm x 200 mm x 25 mm thick table set and jointed, pointed in neat cement slurry with grey cement and no pigment as in floor, complete all as specified and directed.

S&F machine pressed precast concrete interlocking paver blocks with grey cement and no pigment, any shape and size conforming to IS 15658:2006 of 60 mm thickness M35 grade complete all as specified and directed.

M&L for 25 mm thick sand cushioning below paver blocks complete all as specified and directed.

Demolition of reinforced cement concrete as in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work. etc complete all as specified and directed.

M&L for RCC 1:2:4 type B-1 as in Slab supportaed on wall, beams, column in floor , landings, balconies, canopies, deck slabs and in the shelves, cover slab complete all as specified and directed..

M&L for form work to sides and soffits of slab, beams, columns, shelves etc for rough finished surfaces of concrete complete all as specifed and directed.

M & L Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required incl crancking, bending spirally for hooping columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia. complete all as specified and directed.

M & L Demolition of brick work or stone masonry built in cement mortar including all quoines arches,pillar etc but excluding ashlar facing , dressed stone work and precast concrete articles complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 but except bricks complete all as specified and directed.

M&L Brick work with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 as in half bricks. complete all as specified and directed.

Taking down carefully copper/ aluminium unserviceable/ perished point wiring (light, fan, socket or power socket and bulk head fittings) on surface wiring on wooden batten/ casing caping complete including fixture and fittings such as switches, ceiling roses, pandents holder , regulators, sockets, lamp holder, buzzer , light fittings and defective main switch/DB/MCB/Metal plug etc by unscrewing carefully from board etc and making good disturbed surfaces of wall, floors, complete all as specified and directed.

M & L Point wiring for light/fan/bell point controlled by one switch with 1.5 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS with and including PVC rigid conduit (medium grade) having thickness as per IS code with all fittings including galvanised pressed steel sunkum boxes having thickness as specified 3mm bakalite laminated sheet for switches and sockets, including 1.5 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS as earth continuity conductor connected to common earth dolly including cutting, chiseling for concealed piping and making good disturbed surface area and white wash/colour wash to matching with the existing colour complete all as specfied and directed. Note : (a) Colour coding is to be maintained (Ph-Red, N-Black, Half -Yellow, Earth- Green) (b) On RCC roof ceiling PVC conduit shall be provided on surface for fan with proper fixing clips e all as specified and directed.

All as per above item no 104.00 here in before but for one 3 pin socket outlet 5 amp on same board all as specified and directed.

All as per above item no 104.00 here in before but for one 3 pin socket outlet 5 amp on independent board all as specified and directed.

M&L Point wiring with 4 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS with and including PVC rigid conduit (medium grade) having thickness as per IS code with all fittings including galvanised pressed steel sunkum boxes having thickness as specified 3mm bakalite laminated sheet for one 3 pin socket outlet 15 Amp on independent board including 4sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS as earth continuity conductor connected to common earth dolly including cutting, chiseling for concealed piping and making good disturbed surface area and white wash/colour wash to matching with the existing colour complete all as specfied and directed. Note : (a) Colour coding is to be maintained (Ph-Red, N-Black, Half -Yellow, Earth- Green) complete all as specified and directed.

S&F Switch piano flush type one way 5 Amps single pole 240 volts complete all as specified and directed.

S&F socket outlet 2 in 1, 3 pin 5 and 15 amps flush type 240 volt complete all as specified and directed.

S&F socket outlet 2 in 1, 3 pin 5 amps flush type 240 volt complete all as specified and directed.

S&F Switch piano flush type one way 15 Amps single pole 240 volts complete all as specified and directed.

S&F Switch bell push flush type 5 Amp 240 volt complete all as specified and directed.

S&F Bell Multi Music Type, AC 230 volt, Single Pole complete all as specified and directed.

Supply and Fix in replacement existing UNSV decorative box type fitting 4 feet long with blue coloured end caps for LED tube 1x16W LED including LED tube 4 feet long of 16W having bipin holder, connector block etc complete all accessories prewired and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core complete all as specified all as directed

Supply and Fix in replacement existing UNSV tube light fitting with LED 20W inverter batten type fitting 4 feet long aluminium extruded housing, charging time 10-12 hours and back up time 04 hours, IP-20 ,rated voltage 230 V, 50 hz, system wattage 20W +/- 10%, system current less than 102 mA, power factor more than 0.95, system lumen efficiency 100lm/watt,CCT 6500K, CRI more than 80, THD less than 30%, driver efficiency more than 85% complete all accessories prewired and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core all as required at site or directed. Notes: (i) LM79 report from third party (instead of company in house lab) NABL/UL accredited lab (ii) LM 80 report from LED manufacturer (iii) Test certificates to be submitted before commencement of work/ claiming for payment . (iv) Warranty certificate for minimum 2 years to be submitted from OEM.

S & F Ceiling rose, 65x50mm three therminals isolated body (ISI marked) complete all as specified.

S&F Lamp holder Polycarbonate type with back plate having matching colour to holder for angle/batten fittings (ISI marked) complete all as specified and directed.

M & L integrated LED bulkhead 10 watt IP -65 protection connecting electricaly to ceiling rose using cord flexible 3 core PVC insulated over all sheathed with flexible copper conductor of size 0.75 sqmm all as required complete all as specified and directed.

S & F in replacement of CFLs with LED smart Lamp, B22 type, 7 watt complete all as specified and directed.

Supply and fix LED Lamp inverter type 07 watt 230 volts,50 Hz, ,lumen 700 lm, rated current 35 mA, CRI less than 80, Charging time 8 to 10 Hours, operating temperature -10 to 50 degree celcius,back up time 04 Hours, complete all as specified and directed.

Supply and fixing in replacement fan regulator electronic, step type hum free suitable to control speed of fan from 0 to 100% and connecting electrically complete all as specified and directed.

S&F Sheet metal enclosure powder coated factory made (Double door) for DBs, single pole and neutral, 240 volts, 50 Hz, 08 way, IP-43, IK-08 with 200Amps rated bus bar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning, complete all as specified.

S&F in replacement existing unsv distribution board iron clad , double door with IP-54 1K-09 protection suitable for MCCB as incommer and MCB as outgoing 415 Volts 3 phase 50 C/S 4 way, complete with appropriate size copper bus bar and neutral link complete with including one MCCB, 100 amp, 3 pole , 415 Volt with rupturing capacity 16 KA of the same make as of distribution board and and including cutting chases to wall for fixing DB and making good the disturbed wall surface all as required at site or directed by Engr-in-Charge (Outgoing MCB will be measured separately).

M&L 6 to 32 Amps MCB SP ( ISI Marked) 50 C/S 10 KA 'C' sereis complete all as specified and directed.

M&L for repalacement of existing unsv MCB SPN 240 volts any rating from 20 to 32 amps, with rupturing capacity 10 KA. Including providing thimble for out going cables complete all as specified and directed.

Supply and laying in replacement of existing unserviceable/ burnt submain wiring alongwith two single core cable PVC insulated and unsheathed cable with copper conductor FRLS (multistrand) of size 4 sqmm drawing into and including concealed PVC rigid non metallic conduit of 20mm dia , 1.8 mm wall thickness and single core cable PVC insulated and unsheathed cable with copper conductor FRLS (multistrand) of 4 sq mm as earth wire including cutting chases in brick wall, rendering in cement mortar 1:4 and making good the disturbed surfaces to match existing complete all as specified & directed. Note: (i) Two runs of 4 Sqmm single core PVC insulated copper conductor cable(FRLS) and one run of 4 sqmm copper conductor cable (FRLS) as a earth lead and one run of PVC conduit of 20mm dia , 1.8 mm wall thickness wiil be measured as a one unit. (ii) Proper colour coding is to be followed as per IS Specification. (iii) wiring shall be concealed/ on surface with rigid PVC conduit medium grade as per site requirement.

Supply and laying in replacement of existing unserviceable/ burnt submain wiring alongwith two single core cable PVC insulated and unsheathed cable with copper conductor FRLS (multistrand) of size 6 sqmm drawing into and including concealed PVC rigid non metallic conduit of 20mm dia , 1.8 mm wall thickness and single core cable PVC insulated and unsheathed cable with copper conductor FRLS (multistrand) of 6 sq mm as earth wire including cutting chases in brick wall, rendering in cement mortar 1:4 and making good the disturbed surfaces to match existing complete all as specified & directed. Note: (i) Two runs of 6 Sqmm single core PVC insulated copper conductor cable(FRLS) and one run of 6 sqmm copper conductor cable (FRLS) as a earth lead and one run of PVC conduit of 20mm dia , 1.8 mm wall thickness wiil be measured as a one unit. (ii) Proper colour coding is to be followed as per IS Specification. (iii) wiring shall be concealed/ on surface with rigid PVC conduit medium grade as per site requirement.

Supply & Fix water heater storage type, electric, capacity 25 litres. BEE 5 star rated suitable for 8 bar pressure with nano polymer coated tank, incloly heating element, rust proof ABS body etc complete all as specified and directed.

M&L for replacement of existing unsv sheet metal enclosure MCB distribution board single pole and neutral with a two pin and earth plug and socket 20 amps 240 volts, complete with one single pllie MCB of 20 amps complete all as specified all as directed

Supply and Fix in replacement existing unsv sleek LED mirror light fitting 2 feet long 1x10 W including LED tube 2 feet long of same make having ballast, bipin holder, connector block etc complete all accessories prewired and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core all as required complete all as specified all as directed Note for Srl item No 114,115,118 & 130: (i) Driver Efficiency- more than 85% (constrant current driver). (ii) Non isolated type Driver (iii) THD - < 20% (iv) Led Driver current - less than 60 mA (v) Efficiency of Led Fixtrue - 100 lm.watt (minimum) (vi) Efficacy of Led Chip - more than 130 lm/watt (vii) Surge Protection - 2.5 KV & above as per IEC standard (viii) Working Humidity - 95% RH. (ix) Led Make - Nichia/Philips Lumiled/ Cree /Osram /Seoul (x) Life - 50,000 hours at 70% lumens (xi) CRI - more than 80 (xii) Working Temp- 0 to 50 degree C. (xiii) Heat Sink extruded aluminium (xiv) Junction Temp- 85 degree C (xv) Body of Fitting - Extruded aluminium.(xvi) Impact code - Min IK03 or more (xvii) LM79 report from NABL /UL accredited lab (xviii) LM80 report from LED manufacturer (xix) Low/High voltage, reverse polarity, overload and short circuit protection inbuilt in fixture. (xx) IP -20 (xxi) Test certificates to be submitted before commencement of work / claiming for payment. (xxii) Warranty certificate for minimum 2 years to be submitted from OEM.

Supply & Fix Ceiling fan AC sinlge phase 230/240 volts of size 1200 mm sweep BEE 5 Star rated (BLDC) complete including blade ,down rod etc including connecting to ceiling rose all as required or directed. and depositing to MES storeyard complete all as specified and directed.

Supply & Fix Exhaust fan AC sinlge phase 230/240 volts of size 300 mm sweep steel body with louvre including connecting to ceiling rose all as required or directed including connecting to ceiling rose all as required or directed.including dismentling old unsv and depositing to MES storeyard complete all as specified all as directed

M&L Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground (Earth pit not less than 2.25 Mtr deep below normal ground level )with top edge of the plate not less than 1.5 Mtr below normal ground level connecting with galvanized iron GI earth wire 4mm dia by means of bolt nut check nuts and washers of galvanized iron and provision of GI tubing medium grade (ISI marked)of size 15mm for protection of GI earth wire upto test point, 20mm dia GI light grade watering pipe with funnel and wire mesh, RCC pit cover of size 300x300x40mm reinforced with XPM having weight not less than 4Kg/sqmm including 6mm thick MS bar handle made to shape, PCC pit with 1:3:6 type C1 with angle iron frame made of angle iron of size 40x40x4mm, adequate qty of charcoal dust and salt layers all around the earth plate, excavation , earth work in any type of soil, removal of excavated soil and returning filling in all as required at site complete all as specified in plate No 3 of SSR Part-I and all as specified or indicated including testing on completion.NOTE :-Rates inclusive of necessary excavation in any type of soil, earth work, PCC pit, RCC cover, funnel with watering pipe, GI earth strip upto 7.5 m long for connecting to test point etc. all as required at site for complete earthing) complete all as specified and directed.

Supply, laying and testing of LT UG cable, XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sqmm 3.5 core complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in any type of soil. complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering & well ramming in layers n exc 25 cm with any type of soil complete all as specified and directed.

Removing excavated material n exc 50 m and depositing where directed at al level n. exc 1.50 m above the starting point all as directed complete all as specified and directed.

M & L for good quality dry sand cushioning to under ground electric cable on layer of 8 cm thick before laying the cable and second layer of 15 cm thick after laying the cable all as specified in clause 19.75 of MES Schedule part-I (2009) Note : Sand shall be fined sand as specifed and punned thickness shall be measured and paid complete all as specified and directed.

Supply and laying sub class 'B' bricks of old size (230x115x75 mm) or of size locally available , laid along alignment of cable as protection to cable in trenches complete all as specified and directed by Engineer-in-Charge

Supply and fixing for replacement of old unsv bldg light LED Bldg light fittings on Bldg of height not exceeding 7.5 mtrs, comprising of epoxy powder coated housing, enclosed with glass cover in frame, for efficiency not less than 95 lumens/Watt, and minimum wattage capacity of 25 Watt complete all as specified and directed. Note : (I) Driver Efficancy- more than 85% (constrant current driver). (ii) Driver Type- Potted (iii) THD - < 10% (iv) Led Driver current - less than 750 mA (v) Efficacy of Led Fixtrue - 100 lm.watt (minimum) (vi) Efficacy of Led Chip - more than 130 lm/watt (vii) Surge Protection - 4 KV & above as per IEC standard inbuilt in Driver and External SPD 5KV (viii) Working Humidity - 10% to 90% RH. (ix) Led Make - Nichia/Philips Lumiled/ Cree /Osram /Seoul (x) Life - 50,000 hours at 70% lumens (xi) CRI - more than 70 (xii) Lens- Each Led shall be of High Power (1 to 3 watt only) with mandatory modular lens. (xiii) Working Temp- 0 to 50 degree C. (xiv) Heat Sink- pressure die cast aluminium (xv) Junction Temp- 100 degree C (xvi) Body of Fitting - Pressure Die Cast with company logo / make engraved or embpssed in housing LM 6 Grade.(xvii) Impact code - Min IK05 or more (xviii) LM79 report from NABL /UL accredited lab (xix) LM80 report from LEDmanufacturer

(xx) Low/High voltage, reverse polarity, overload and short circuit protection inbuilt in fixture. (xxi) MS Clamp fittings with nut bolts and GI bracket 32 mm dai 0.90 metre long, junction box included in the rate. (xxii) Test certificates to be submitted before commencement of work / claiming for payment. (xxiii) Warranty certificate for minimum 2 years to be submitted from OEM.

Notes : The Schedule of Credit amount shall be deducted from the total of this schedule(BoQ) to arrive at Contract Sum.

Abrol construction co

M/S BISHAN DASS AND SONS

Ms Dalip Kumar and Co.

Walia trading co