AR and MO various roads under PWD Division South West Road-1 during 2026-27. (SH- Providing and fixing road furniture and other traffic safety measures on various roads under Sub-Division-II, New Delhi).

Providing and fixing Glow studs of size 100x20 mm made of heavy duty body shall be moulded ASA (Acrylic styrene Acryloretrite ) or HIP (High impact polystyrene) or ABS having electronically welded micro- prismatic lens with abrasion resistant coating as approved by Engineer in charge. The glow stud shall support a load of 13635 kg tested in accordance with ASTM D4280. The slope of retro- reflective surface shall be 35 (+/-5) degress to base .The reflective panels on both sides with at least 12 cm of reflective area up each side. The luminance intensity should be as per the specification and shall be tested as described in ASTM I: 809 as recommended in BS: 873 part 4 : 1973. The studs shall be fixed to the Road surface using the adhesive conforming to IS, as per procedure recommended by the manufacturer complete and as per direction of Engineer-in-charge.

Modified estimated cost after using correction factor on DSR 2023 on account of GST @ 0.973 on DSR items

Add Cost Index 4.03% on DSR Items

Providing and Fixing of Solar Raised Pavement markers made out of polycarbonate molded body with circular shape, solar powered, LED self-illumination in active mode, 360-degree illumination and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face in passive mode. The marker shall support a load of 20,000 kg tested in accordance to ASTM D 4280. The marker should be resistant to dust and water ingress according to IP 65 standards and should withstand temperatures in the range of 0°C to 70°C. Typical frequency of blinking is 1 Hz. There should be current losses of less than 20 microamperes at 2.4V in sleep/parking mode to enhance the life of the marker and a full charge should provide for a minimum autonomy of 50 hours. The height, width and length shall not be less than 10 mm × 100 mm × 100 mm. Also, the surface diameter of the marker shall not be less than 100 mm respectively. The weight of the marker shall not exceed 0.5 kilograms. Fixing will be done by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive and complete as directed by the engineer. The solar raised pavement markers shall be tested for Compression strength of 20,000 Kg, IP 65 rating, Blinking frequency from government lab (CRRI/ARAI/CAT/CPRI) as per requirement of MoRTH and report shall be uploaded while quoting the tender. The bidder shall submit the sample of the Solar STUD complying to the item specification in schedule & Ministry/IRC conditions. Sample of Solar STUD shall be signed by the Representative of the Solar STUD OEM on the back side.

Providing and placing sand barrels made of durable impact-resistant material, of yellow colour with black lid, designed for easy movement and handling, capable of being arranged in different configurations to achieve required sand-filled weights of 90 kg, 180 kg, 320 kg, 640 kg and 950 kg as per standard array geometries, comprising single-piece sand containers to eliminate sand leakage (without edge seals), provided with cone inserts to facilitate easy transportation, storage and installation, complete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge.

Providing and fixing flexible spring posts / bollards made of virgin special flexible Polyurethane (PU) material manufactured by single moulded process, circular/cylindrical in shape, capable of restoring to original position without damage to vehicle or post after high-speed vehicular impact, fitted with PMMA reflectors of 70 mm diameter of approved colour (amber/white) riveted on both sides at the circular top, provided with highly reflective tape of minimum 15 mm width between reflector and circular top on both sides for improved night visibility, further provided with two bands of highly reflective Type-IV 5930M reflective tape of minimum 70 mm width on the post, UV-stabilised to prevent discoloration, suitable for fixing department’s logo as and when required by Engineer-in-Charge, of height about 800 mm, base diameter about 250 mm, base provided with four holes of 12 mm diameter for anchoring, weighing about 1.4 kg, fixed on road surface complete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge.

Providing and fixing road delineators of height 1000 mm, made of Mild Steel (MS) body with powder-coated finish for longer service life, fitted with high-performance Type XI retro-reflective sheeting conforming to IRC:79-2019 and MoRTH specifications, having superior engineered design for maximum day and night visibility, provided with grooved edges for fixing of reflective sheeting to prevent vandalism, of size approximately 100 mm × 30 mm × 1000 mm, complete with all fittings and accessories, installed at required locations complete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge.

Providing and fixing flexible median markers made of flexible thermoplastic body, fitted with fluorescent yellow Type XI retro-reflective sheeting conforming to IRC:79-2019 and MoRTH specifications, designed for superior flexibility and maximum visibility during day and night, provided with deep grooved edges and side sealing to prevent vandalism of reflective sheeting, having single shank arrangement for easy installation by grouting, of size and shape as specified in IRC:79-2019, complete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge

Providing and fixing Road Safety Bollards used to guide the traffic for safe direction. It is generally installed at the crossing, start of the central verge, diversions etc. The Road Safety Bollard Should has following features:- Pipe Dia should be 65 mm approx MS Pipe. Length of the Pipe should be1825 mm approx. Reflector Plate: Square shape ABS plastic plate size of 385×385 mm and 3 mm thickness. Reflector: Ultrasonic laser welded & Riveted with 09 Nos. of 100 mm PMMA (Acrylic) made high intensity reflectors for better durability. Retro Reflectivity of these reflectors should be 18mcd/Lux. MS Round Plate: MS plate in round shape of 400 mm has been embedded with 1 mm thick Aluminium plate having high intensity Retro-reflective tape. (For Messages and Arrow Purpose). MS Rectangular Plate: MS rectangular plate of 300x75mm size 2mm thickness. (For Messages Purpose). All three plates should be mounted on a white powder coated 65mm dia MS pipe and complete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge.

Providing and fixing The body of Median Marker should be made of ABS plastic material. Reflective Tape (Type IV) of 100 mm in diameter should be pasted as a circle on both the sides of the plastic body for excellent reflection in the night hours. Color of the Reflective Tape should be Yellow & ABS Body should be Black. A special ring should be attached (both sides) on the top of the shield to protect the reflective tape from tampering or peeling off. Two mounting holes should be provided. A special plastic base of size 115 mm x 130 mm approximate with four mounting holes should be provided on the bottom of the median marker for better grip with the surface. Height of the Median Marker should be 120mm approx. Weight of the Median Marker should be 240 grams approx and complete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge.