Startup TN Thoothukudi

Amount

Dismantling Brick / Stone Masonry in cement mortar walls under 3m high etc., complete.

Precast Concrete Block Masonry using Autoclaved Cellular Aerated Concrete Block of size 600 x 200 x 200mm conforming to IS 2185 (Part 3) : 1984 with Self Curing AAC Joint Mortar for Partition Wall of non load bearing type in accordance with IS 6041:1985 including neat finishing etc., complete complying with standard specification and as directed by the TANSIDCO Engineers.

Plain Cement Concrete 1:5:10 (One cement, five crushed stone sand and ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and including curing etc., complete complying with standard specification and as directed by the TANSIDCO Engineers. (As per TNBP No. 28)

Reinforced Cement Concrete 1:1.5:3 (One cement, one and a half crushed stone sand and three hard broken stone jelly) using 20 mm gauge hard broken granite stone jelly for all RCC items of works excluding cost of reinforcement grill, fabricating charges centering and shuttering but including super plasticiser, laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc. shall be finished smooth with Cement Mortar 1:3 (One cement and three M Sand) and kraft paper laid over it without claiming extra etc., complete complying with standard specification and as directed by the TANSIDCO Engineers. (As per TNBP No. 30)

Supplying and erecting Centering for plane surfaces such as RCC Floor / Roof Beam, Lintels, Cantilever Beams, Bed Blocks etc. with necessary supports and strutting upto 3.60m height in all floors with all cross bracings using MS Sheets made of 10 gauge thick welded with MS angle of Size 25mm x 25mm x 3mm for boarding laid over Steel Adjustable Span of size 2m x 2m (expandable upto 3.60m) and Silver Oak Joists of size 10 x 5 cm spaced at 50cm to 60cm c/c and supported by Steel Adjustable Telescopic Props of size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) spaced at not more than 50 to 60cm c/c etc., complete complying with standard specifications. Steel Adjustable Span and Steel Adjustable Telescopic Props shall be provided as directed by the TANSIDCO Engineers. (Payment for centering shall be given after the concrete is laid). (As per TNBP No. 86 & 86A)

Plastering the surface of walls with Cement Mortar 1:5 (One cement and five crushed stone sand), 12mm thick including mortar plasticizer at 200ml per 50Kg of cement used, curing etc., complete complying with standard specification and as directed by the TANSIDCO Engineers. (As per TNBP No. 56 & 57)

Flooring with Brick Jelly Concrete 1:2:5 (One of cement, two of crushed stone sand and five of aggregate) using brick jelly of size 20mm including labour charges etc., complete complying with standard specification.

Paving the floor with best quality Double Charged Vitrified Tiles of size 800 x 800 x 10mm and variety conforming IS 15622 with water absorbtion less than 0.08% of approved colour and shade laid over cement mortar bed of 20mm thick in Cement Mortar 1:3 (One cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer in all floors and the top pointed with Water Resistant Tile Epoxy Grout etc., complete complying with standard specification and as directed by the TANSIDCO Engineers. (The make and brand of the tiles should be got approved by the Executive Engineer before use on works). (As per TNBP No. 39A)

Flooring with Designed Colour Ceramic Tiles of size 305 x 305 x 6mm and variety conforming to IS 15622 laid over cement mortar bed of 20mm thick in Cement Mortar 1:3 (One cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with Water Resistant Tile Epoxy Grout at the rate of 0.27 Kg / sq.m etc., complete complying with standard specification and as directed by the TANSIDCO Engineers. (The make and brand of the tiles should be got approved by the Executive Engineer before use on works). (As per TNBP No. 39A)

Dadooing walls with best quality Double Charged Vitrified Tiles of size 600 x 600 x 8mm conforming to IS 15622 in Cement Mortar 1:2 (One cement and two crushed stone sand), 10 thick with mortar plasticizer and pointing the joints with Water Resistant Tile Epoxy Grout at the rate of 0.27 Kg / sq.m neatly in all floors, curing etc., complete complying with standard specification and as directed by the TANSIDCO Engineers. (The make and brand of the tiles should be got approved by the Executive Engineer before use on works). (As per TNBP No. 39A)

Painting two coats of newly plastered wall surface with ready mixed Plastic Emulsion Paint of first class quality and approved colour over a priming coat including thorough scrapping, clean removal of dirt wherever required and two coats of wall putty etc., complete complying with standard specification and as directed by the TANSIDCO Engineers. (As per TNBP No. 66A)

Fabricating Supplying and fixing in position of Aluminium anodised Powder Coated (any colours) of single leaf fully glazed Door shutters with 5.50 mm thick glass. The outer frame shall be with aluminium box section 101.60x44.45x3.18m at 2.319kg/m and Shutter frame made of section with Vertical & Top rail: [email protected] kg/m, Bottom rail: 100x44.45x2.50mm@ 1.974 kg/m, Lock rail : 50x44.45x2.5mm @ 1.292 kg/mAlu. Clips: 17.15x17.27x1.50mm @ 0.176 kg/mAlu. Handle: 100x30mm @ 0.988 kg/m and necessary accessories such as Alu. clips rubber beading, full length of handles on one side, lock, furniture fittings such as, Hinges, rubber bush, including cost of materials, labour charges and power consumption charges required for fabrication including chipping, dismantling and making hole to the required extent in RCC column, beam masonry with power drill wherever necessary and redoing the damaged portion to the original condition after fixing etc. complete. All the Alu. Section are to be anodised with matt finish under electrically controlled condition in accordance with IS 1868/1962 for an average anodic film thickness of 15 microns etc., complete.

Supplying and fixing Solid PVC Door Shutters with Frame using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC Sheets. Shutter using 5mm thick solid PVC Sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The overall size of styles shall be 50mm x 30mm. The overall size of top rail, lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm with suitable rabate for housing the shutter etc., complete complying with standard specification and as directed by the TANSIDCO Engineers.

Gypsum Board Partition : Supplying and fixing of 10 mm thick Gypsum Board Partition to a thickness of 50 mm which includes double side parition and providing 25 x 25 mm steel tube. The rate shall include the cost of gypsum board including making holes,cutouts, patch fittings, necessary hardwares, applying sealants, wastage etc, as required for completion the works and as directed by Engineer-in-charge.

Supplying and fixing Gypsum Board false ceiling including cost of all GI metal frame suspensions, Gypsum board and labour charges etc complete as directed by the Engineer- in - Charge.

Supply, Installing, testing and commissioning of Wash Hand Basin with all accessories such as Cast Iron Brackets, 32mm dia CP Waste Coupling, Rubber Plug and Chain, 32mm dia pvc Waste Pipe, 15mm dia brass ball Valve,15mm dia Nylon Connection, 15mm dia Brass Nipples,15mm CP sensor Pillar Tap etc White without Pedastal a) Under Counter Basin size: Parryware - Model : Wash Basin - C04711C - INDUS 500 X 400 - CTH ULTRAWHITE b) Supply ,Installing, testing and commissioning of Bottle Trap Bottle trap - T3201A1 - BOTTLE TRAP LIGHT c) Supply ,Installing, testing and commissioning of SS Waste Coupling Waste coupling - T9899A1 - Full Thread Waste Coupling- 80mm d) Supply ,Installing, testing and commissioning of Angle Valve - Angle cock - T9880A1 - Cute Angle Valve

Supply, installation and fixing of stainless steel body liquid soap dispenser with PVC rawl plug & C.P. brass screw complete as required. (Material : SS 304, Dispense : Foam soap, Battery : 4 x AA alkaline duracell, sensing distance : 5-9cm, Dispense volume : 1-2ml) Make : Euronics -ES802F

Supply, Installing, testing and commissioning of stainless steel sink without drain board , with 15m dia CP sink Cock , CP waste coupling, 32mm dia CP bottle trap with extension pipe, supporting CI bracket to support sink, and CP wall flanges, all complete set of approved make. . (Pantry) Make :Hafelei Stainless Steel splash Sink a) Supply ,Installing, testing and commissioning of Angle Valve - Angle cock - T9880A1 - Cute Angle Valve b) Supply ,Installing, testing and commissioning of Bottle Trap Bottle trap - T3201A1 - BOTTLE TRAP LIGHT c) Supply ,Installing, testing and commissioning of SS Waste Coupling Waste coupling - T9899A1 - Full Thread Waste Coupling- 80mm Make / Model : Parryware T4621A1 - Claret Wall Mounted Sink Cock

Supply and fixing in position of best Indian make White Glazed earthernware lipped mouth flat back Urinal of best quality and approved make of size 430mm x 260mm x 350mm with GI pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2 Nos. and fixing the urinals in position with necessary TW plugs, clamps, screws etc., including dismantling masnory and re-doing the same to the original condition etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc., complete complying with standard specifications and as directed by the TANSIDCO Engineers. (The urinal should be got approved by the Executive Engineer before use on works). (As per TNBP No. 102 & 103)

Supplying and fixing in position White Glazed European Water Closet of best quality and approved make with 100 mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws etc., including supplying and fixing 10 litres capacity PVC flushing tank fixed onto wall etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe, dismantling the masonry and re-doing the dismantled masonry to original condition etc., complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Enginer before use on works). (As per TNBP No. 102 & 103)

Supplying and fixing in position of Chromium Plated Two Way Bib Cock with Health Faucet of approved make conforming to BIS specifications and quality including cost of shellac, thread, cutting and threading wherever necessary etc., complete complying with standard specification. (Cocks should be got approved by the Executive Engineer before use on the works).

Supplying and fixing in position of Special Type Mirror of size 1000 x 780mm of approved quality, brand and colour fixed with brass screws, teakwood plugs including labour charges etc., complete complying with standard specification.

Supplying, fixing and testing of approved make of 6kg / cm2 PVC pipes confirming to IS 4985-2000. and fittings (moulded and fabriacted fittings ) such as tee, elbow, 'y' , coupler, etc confirming to IS 7834 with latest amendment for soil and waste pipe works in toilets etc. Pipes shall be laid in under floors/ under ceiling / sunken floor as per approved drawings. For laying the pipes in walls, before chasing, the pipe line routing shall be marked using chalk line with help of tube level,Pipes and fittings shall be cleaned with pipe cleaners and joined by approved make solvent cement. After laying the pipes, before closing the pipes, gravity test to be conducted and got the approval from the engineers in charge.

75mm dia

110mm dia

Providing & fixing in position deep seal multiway PVC floor Trap of size 100 x 75mm with cockroach trap and PVC extension piece of required length depth to suit site conditions and multiple inlets, to suit site conditions with inlet sizes ranging from 40 mm to 75 mm. The bottom of the sump shall be dummied water tight. Wherever, sumps are shown to have water seal, the seal depth shall be minimum 40 mm. The sump shall be laid in cement concrete bed with 1:2:5 mix with 40 mm brick jelly bed all around and finished with cement mortar 1:3. Providing and fixing heavy class C.P. brass mosquito proof grating with frame of approved design including setting in floor with cement mortar to match with floor finish. (Sample should be got approved ) include urinal trap

Supplying and fixing in position first quality and approved variety of 25mm Dia Gun metal gate valve / wheel valve with BIS make including cost of shellac, thread balls, etc., complete complying with standard specifications ( for both internal and external water supply arrangements). the valves to be used on work shall be got approved by the executive engineer before use on work.

Linear Workstation - Workstation Area - Sharing Size : 1200x 600 x750mm Table Top is made up of 25mm thick PLPB Table Top with 2mm PVC Edge Banding . Understructure : MS Powdercoated Legs 40 x 40 Slant legs. Wire Management : Grommet Hole -65mmDia 250mm ( Ht ) Raceway below the table top Main Screen : 18mm Thick & 300mm(ht) fabric magnetic privacy with rubber beading. CENTER T LEG : MS 40X40 MS 40X40 Square leg with CRCA Pipe of 1.6mm thickness of 60 microns Powder coated leg for Table top Stability. Passage side modesty : MS powder coated 450mm(ht)

WORKSTATION CHAIRS. AURA - Medium Back •Sturdy 50mm G.F Nylon dual- wheel Castors , •Glass Filled Nylon Base , •Class 4 Gas lift as per DIN Standards 4550: 2004-12 , •Single Position Locking Synchro Mechanism , •Height Adjustable 2D PU Armrest, •Glass Filled Nylon Backrest with Mesh , •Seat Upholstered with PU Foam & Fabric , • Height Adjustable Lumbar Support.

Visitor Model Meshback Chair S type Fixed Handle

Cabin Table: Main Table Size - 2100 x 100 x 750mm Side Storage Size - 2000 x 500 x 750mm Back Storage Size - 2700 x 450 x 750mm Main & Side table Specifications: Top panel: 25mm Thk pre laminated particle board Edge: All exposed area with 2mm thick PVC edge lipping LEG : Slant or Straight leg 40*40mm size tube, tube thickness 1.6mm with powder coating finished. SUPPORT BEAMS : 40*40mm ms tube with 1.6mm thickness and with ms powder coating finished. MODESTY : 1.2mm Thk ms modesty panel with powder coating finished in 400mm height. Flip cover 400mm PLB SIDE & BACK STORAGE UNIT: Top & Sides: 18mm Thk pre laminated particle board Back: 6mm Thk pre laminated particle board Edge: All exposed area with 2mm thick PVC edge lipping FASCIA: 18mm Thk pre laminated particle board. Handle: I shape handle Lock: Key lock

Main Chairs: Imported Half Leather Chair Fixed handle,Synchro Tilting Mechanism,Imported Gaslift,Chrome base,Heavy

BOARD ROOM CHAIRSWEBSTAR: Medium Back with Adjustable Handle & softpad with Chrome Base,Heavy Wheel, Synchro Tilting Mechanism,Molded Foam & Fabric

Conference Table: Size - 3150 x 1200 x 750mm TABLE TOP :25mm Thick Pre Laminated particle Board with 2mm PVC edge banding on all side with Flip Cover Hole Provision. (400mm Flip Cover). LEG : Slant type Legs, Tube thickness 1.6mm with ms powder coating finish. Cable entry Box Provided. Supported Cross Bar 40*30mm Size tube with 1.5mm thick sheet and powder coating finish. Below Table top Box Type Raceway.

Training chars with writing pad

Pantry Unit: Size - 6000 x 600 x 800mm Supply and installation of Counter for Pantry and Cafeteria, The storage of countertop to be made of 19mm BWR ply with necessary. The storages to be with shelves, made of 19mm thick BWR ply with swing shutters with all necessary accessories like concealed auto closing SS hinges,

Center Table: Size - 600mm dia, 400mm height Table top 18mm thick prelam particle board with edge banding finish. Leg 20mm square ms leg with powder coating finish.

Transportation, loading and unloading charges

Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board ( with MCB Incomer ) with double door (metal door) with 1 no. 63 A 4 P MCB as incoming, 1 No. 63A 100mA 4P ELCB/RCCB and 12 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Higher End Incoming - 63A 4P MCB - 1 No. Sub incoming -63A, 100mA 4P ELCB/RCCB - 1No. Outgoing - 6 to 32A SP MCB - 12 Nos.

Supply and fixing of 8 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board ( with MCB Incomer ) with double door (metal door) with 1 no. 63 A 4 P MCB as incoming, 1 No. 63A 100mA 4P ELCB/RCCB and 24 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Higher End Incoming - 63A 4P MCB - 1 No. Sub incoming -63A, 100mA 4P ELCB/RCCB - 1No. Outgoing - 6 to 32A SP MCB - 24 Nos.

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming, 25 Amps 30 mA DP as sub incoming and 8 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Higher End

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming, 25 Amps 30 mA DP as sub incoming and 4 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Higher End

Supply and fixing of 4P enclosure box with 63A 4P MCB on wall.

Supply & fixing of NUMERIC LEGRAND –HPI 33 EVO 20KVA FMI with Isolation transformer (3Ph-3Ph) 12V/240 VDC, Online Double Conversion UPS including MS rack for housing the batteries along with necessary interconnection cables. Warranty: 2 Year for UPS (Backup time - 30mins.) Warranty: 2 Year for UPS 12V / 42 AH / 20Nos of SMF Batteries for 30minutes backup timing Make: EXIDE/QUANTA Warranty: 2 Years for SMF Batteries.

Supply and clamping of 4 x 25 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply and fixing of brass cable gland and Termination for 4 x 25 sq.mm. PVC armoured LTUG cable with earth connection

Supply and Run of 4 of 16 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC flexible hose on wall and ceiling with continuous earth wire connection of 16 sq.mm copper wire with painting of suitable colour.

Earthing as per PWD standard with an earth electrode of 2 metre Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry work

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection

Supply and Run of 1 of No.8 SWG copper wire for earth connection

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories with Module GI switch box in flush wall with 6A one way module switch with module front plate with painting of Suitable colour with continuous earth wire connection of 1.5 sq.mm copper wire for Open MS conduit Light point / fan point (for electronic regulator) (5 points / Coil) Higher End

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories with suitable Module GI switch box in flush with wall with 1 no. 6A one way module switch and 1 no. 6A 3/2 pin module socket with module front plate with painting of Suitable colour with continuous earth wire connection of 1.5 sq.mm copper wire for Open MS conduit Plug point ( 8 points / Coil) Lower End

Supply and run of 2 of 1.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable gauge MS Flexible pipe on wall and ceiling with continuous earth wire connection of 1.5 sq.mm copper wire

Supply and fixing of 30W 2x2 LED square Recessed type fitting with suitable frame wherever necessary on false Ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of 30W 4 feet compact LED tube in suitable general purpose industrial batten made of compact CRCA sheet steel with connection.

Supply and fixing of 19W LED Round Recessed type fitting on false Ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of 3 nos. 6A two module 3 pin socket, 1 nos. 6A one module switch with suitable module cover plate (plastic) on existing wall / Truf / Box beneath the table with connections. Lower End

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch on suitable module surface mounting Box (Plastic) with module cover plate (plastic) on wall with connections. Lower End

Supply and Run of 2 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC flexible hose on wall and ceiling with continuous earth wire connection of 1.5 sq.mm copper wire with painting of suitable colour

Supply and run of 2 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with continous earth wire connection of 2.5 sq.mm copper wire with painting of suitable colour

Supply and Run of 2 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper wire and making good of the concealed portion.

Supply and run of 2 of 6 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with continous earth wire connection of 2.5 sq.mm copper wire with painting of suitable colour

Supply and Run of 2 of 6 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 2.5 sq.mm. copper wire and making good of the concealed portion.

VRF SYSTEM Note: VRF Units shall meet minimum efficiency requirements as per latest ECBC norms. EER & IEER values as specified in ECBC to be met or as per latest BIS standards, if they are more stringent. Air Cooled VRF System Supplying, installation, testing and commissioning of Air Cooled Variable Refrigerant Volume System suitable for R410A and 415V, 50 Hz, AC supply. The unit shall consist of indoor units and external condensing units and other accessories complete in all respects. The unit shall be fully charged with gas and oil.

Outdoor Unit Supply & Installation, testing and commissioning of Outdoor units consists of 100% inverter compressors, condenser fan motor with variable speed controllers & aero-spiral fan blade and, e-pass heat exchanger, safety valves, solenoid valves, receiver, capillary tube, check valve, electronic expansion valve, high pressure switch, low pressure sensor, pressure regulating valve, refrigerant filter, stop valve, accumulator and refnet kits. The COP of the VRF system shall be minimum 3.5 at AHRI condition. Rate shall be inclusive of R-410A refrigerant & oil pre charging, vibration isolators, supports, necessary mounting brackets/ pedestal works etc. The outdoor unit shall be sized to deliver following rated capacities at 40 deg C ambient condition which excludes de-rated capacity due to excess length of refrigeration pipes, change in indoor dry bulb & wet bulb temperature. All the compressors shall be rated for continuous operation. As per specification & tender drawings.

All the units shall be provided with built-in microprocessor control panel, for automatic operation and capacity control. Machines shall be suitable for working with BMS system. Each VRF module must have accumulator to handle liquid and safe guard compressor against liquid flood back due to dynamic load condition VRF system shall have auto Restart function i.e. In case of power failure, units should restart automatic when power resume. VRF system shall have auto bypass i.e. If any one IDU have any electric or PCB failure, rest of the system should continue to operate. The VRF system shall have free phase technology, which shall correct phases automatically in case of phase reversal. More than 20 HP make a module combination Make : Daikin, Voltas, samsung ,LG & Hitachi 30 HP

VRF-4 Way cassette units Supplying, installation, testing and commissioning of Ceiling Suspended Cassette Type Metallic body Indoor Units each complete with coil, filter, etc. Air conditioners with evaporating unit comprising of cooling coil, blower with motor and 220 volt, 1 phase, 50 Hz, AC supply all as per specifications. The rate will also include for complete indoor unit supports

Refrigerant Joints and Headers Supply, installation, testing, and commissioning of Imported fittings Y-joints, distributor and headers for all Indoor units as per layout drawings.

Refrigerant Piping for VRV system Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable size cable tray/adjustable ring type hanger supports, jointing/brazing including accessories, insulated with Class-O closed cell elastomeric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines & cladded with 26G aluminium sheet. all accessories as per specifications etc. as required. All connections of Refrigerant piping shall be in high grade Copper of Refrigeration quality with Eddy Current Testing and material test Certificates.

6.40 mm dia

9.50 mm dia

12.70 mm dia

15.90 mm dia

19.10 mm dia

22.20 mm dia

Refrigerant Piping for VRV system Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable size cable tray/adjustable ring type hanger supports, jointing/brazing including accessories, insulated with Class-O closed cell elastomeric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines & cladded with 26G aluminium sheet. all accessories as per specifications etc. as required. All connections of Refrigerant piping shall be in high grade Copper of Refrigeration quality with Eddy Current Testing and material test Certificates.

25.40 mm dia

28.60 mm dia

31.75 mm dia

36.90 mm dia

41.30 mm dia

DRAIN PIPING Supply and erection of following Heavy Duty PVC pipe with all joints, reducer, necessary elbows and tees, supporting arrangements, etc.

40 mm dia

32 mm dia

25 mm dia

Transmission & Control Wiring Supply and laying of 3Cx1.5 sq.mm.Shielded Communication cable from ODU unit to all refrigerent IDU Units for Communication etc.,

Providing additional R410A gas charging for the ODU units

SUPPLY & INSTALLATION OF AIR-CONDITIONER WITH COPPER COIL. 1.5 TR Split Type AC Unit - 3 Star Rated

Supply and installation of 4 KVA capacity Automatic Voltage Stabilizer with time delay relay

Supply and laying of 5/8” and 3/8” copper pipe (Extra beyond 3 metres supplied with AC unit)

Supply and fixing of MS stand for fixing outdoor unit

Supply, Fabrication and erection of fabricated ducting made up of GI Sheets of 24 Gauge thickness 24 Gauge – factory fabricated

Supply and fixing of extruded aluminum powder coated, Supply and return Air Grilles / Diffusers with Volume Control Damper

Supply and installation of GI volume control damper (Rectangular / oval) low leakage( handle type ) made out of 1.6mm thick galvanised sheet steel frame and opposed blades of 1.6mm galvanised steel with suitable links, handles, levers and quadrants for manual control of volume of air flow and for proper balancing of air distribution system as per specification

Supply, installation and testing of round flexible duct inner core should be made of triple lamination of Aluminium Foil, Polyester & Metalized polyester film permanently bonded to a coated spring steel wire helix. Fiberglass insulation shall be of 25mm thick with minimum density of 16 kg/m³. The outer insulation jacket vapor barrier shall be made of fiber glass reinforced metalized polyester film laminated with aluminium foil as per the technical specifications. The rate shall be inclusive of hose clamps, supports,bolt,nut etc as per specification.(1.2 Mtr) Dia 100mm

Supply, installation testing & commissioning of Butterfly damper should constructed with Not less than 0.8mm thick galvanized steel sheet, with single flap, necessary stopper, flanges, grooves 150-mm length, neoprene gasket at the edge of blade to reduce leakage and with required hardware and accessories as per specification. Include locking device to hold single-blade dampers in a fixed position without vibration & engraved marking on position of damper, as per specifications. Dia 100mm

Supply, Installation, Testing & Commissioning of air distribution system consists of factory fabricated GI sheet circualr duct

1000 Cfm - 15 mm external static Inline fan with all necessary supports. (AC fresh air). Fan shall be provided with in built fan regulator.

Supply & laying of CAT-6 cable

Supply & clamping of 25mm PVC pipe

Supply & fixing of RJ45 socket with suitable cover plate

Supply & fixing of 36U Rack with 2 Nos. of Fan, 1 No. of Server /IT Rack mount power distribution unit, 1Ph, 230V, 50/60Hz, 2U standard with 6 X Indian socket 5A, Inlet Plug type 6A Indian Plug, 8A Fuse, 1 No. of Tray and necessary accessories

Supply & fixing of Fully Managed 10 / 100 / 1000 Layer-2 Network Switch with 1G Uplink - Higher End/24 Port with 4 Nos. of Fibre Port

Supply & fixing of 8Port PoE switch for CCTV IP Camera

Supply & fixing of 24 Port Patch Panel – Fully Loaded

Supply & fixing of 1 mtr. Patch cord for rack end & user end

Supply & fixing of D-Link DAP-2680 Wireless AC1750 Wave 2 Dual-Band PoE Access Point features cutting-edge Wave 2 technology that brings greater speeds, efficiency, and security to your wireless customers.

Supply & fixing of Pop-up box with 2 Nos. of 6A socket, 1No. of switch, 1No. of RJ45, 1 No. of RJ11 and 1 No.of HDMI ports (Legrand)

Supply & laying of 10mtr. HDMI cable

Supply & fixing of 8 Channel - 1 SATA Network Video Recorder which should support minimum of 5MP Camera

Supply & fixing of 4 TB Hard Disk for NVR

Supply & fixing of 4 MP IP Dome Camera

Testing, Commissioning & Dressing of switches, patch panels & other components in the Rack with tagging & connection complete

Supply & installation of Biometric device Make: ESSL Model: K30 Pro Features: Finger print capacity - 2000 Card capacity - 10000 Finger print sensor - 500 DPI optical With Battery backup

G ILANGUMARAN (BID ID -1550141)