Certain repairs to joinery wk, sanitary fittings, flooring, roofing and allied B/R Wk in OTM Accn at Mil Stn Fazilka

Amount

Taking down chowkats or frame with shutters(without taking off shutters from the frame not exceeding 1.50 sqm each & removing to store all as specified and directed.

Taking down chowkat with shutter exc 1.5 sq.m but n.exc 4 Sqm each and refixing the shutter in same opening all as specified and directed.

S&F solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tubes, as per specifications and drawing complete or as directed.

S&F factory made solid PVC door shutter 30mm thick(style) consisting of frame made out of MS tubes for bottom and top rails. MS frame shall be covered heat moulded plain colour PVC 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail& bottom rail on either side & as gap insert for top rail & bottom rail; Panelling for plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, suppling and fixing in the frame at the site as per specification.

S&F Aluminium handle cast type anodized 125 mm long all as specified and directed by Engineer-in-Charge.

S&F Aluminium anodized barrel tower bolt of extended section and fixed 150 mm long all as specified and directed by Engineer-in-Charge.

S&F 100 mm long butt hinges extruded almiunium alloy with galvanised mild steel hinges pin, anodised and fixed all as specified and directed by Engineer-in-Charge.

S&F Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and as shown on drawing (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life)

S&F 18mm thick PVC sheet having one side decorative laminated sheet all required brackets SS screws etc. the panel shall be fabricated using adhesive and screws where ever required.all the edges shall be covered with 2mm thick edge bonding tape or 90 degree edge bent finish as per make and specification including fitting i.e. magnetic catcher,stainless steel handle approved by Engineer -in-Charge.

S & F pressed steel door frames with one or more rebates including necessary fixing lungs hinges lock strike plate etc complete all as specified size of frame 105 x 60mm all as specified and directed by Engineer - in - Charge .

S & F pressed steel door frames with one or more rebates including necessary fixing lungs hinges lock strike plate etc complete all as specified size of frame 125 x 60mm all as specified and directed by Engineer - in - Charge .

Ditto Ser no-12 as above but size 75x60 mm as in cup board frames all as specified and directed by Engineer - in-Charge.

M&L Cement concrete 1:2:4 type B–1 filling of pressed steel frame and hold fast blocks etc all as specified and directed by Engineer - in - Charge.

S & F 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; size of members of shutters as specified in SSR Part – I, Section – 8, clause 8.20 (a) ; supplied and fitted to chowkats all as specified.

S & F flush shutter 35mm thick solid core construction with block board core and plywood face panels commercial type on both sides with lipping / frame to match all as specified and directed by Engineer - in - Charge.

M&L 35mm thick 2nd class hard wood plain framed panelled shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces.The size of rail and stile as per IS:1003 (Part1),kiln seasoned and chemically pressure treated, all as specified and directed.

M&L 18/19 mm thick prelaminated partical board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work.

S&F Stainless steel tower bolt 150mm long heavy duty all as specified and directed by Engineer - in - Charge.

S&F stainless steel handles of size 150mm heavy duty all as specified and directed by Engineer - in - Charge.

S&F Stainless steel sliding door bolt with hasp and staple ( bolt type) and fixing clips of sheets cast or extruded section and fixing bolts of extruded section or stainless steel 300mm size all as specified and directed by Engineer-in-charge.

M&L preparing surface of wood and wood based surface new on any description not other wise described over 10cm with or grith and applying two coat of synthetic enamel paint over a coat of pink primer all as specified and directed by Engineer - in - Charge.

M & L for preparation of old painted wooden surfaces of any description over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint all as specified and directed by Engineer - in - Charge .

M & L for preparation of old painted steel surfaces of any description over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint all as specified and directed by Engineer - in - Charge .

M&L applying two coats of synthetic enamel paint over a coat of red oxide 0r zinc chromate primer including preparation of new steel or iron surfaces exc 10 cm width or girth, complete all as specified and directed.

S & F in repair steel window 1.25 mm thick Box type (primer coated) ERW hollow P section of size 60 mm x 25 mm single rebated comprises gauged skelton shutter ERW Section 50 mm x 20 mm and 1 mm thick with two open able leaf consisting two Nos of sash bars of flat iron 12 mm x 3 mm complete welded to frame with one vertical mullion of ERW box type T section of size 60 mm x 25 mm and 1.25 mm thick including cutting holes and making good dismantled portion in PCC (1:2:4) type B-1 four Nos for each window including following fitting welded to the frame shutter : (a) Hold fast 150 mm long of 12 mm x 3 mm made to shape - 04 Nos per window. (b) Handle of Z section 20 mm x 25 mm, 100 mm long 1 Nos per leaf. (c) MS tower bolt 150 mm long - 2 Nos per leaf. (d) MS pintol hings of size 100 mm x 14 mm - 2 Nos per leaf. (e) Z section 20 mm x 25 mm x 100 mm long stopper per leaf. Note : Wire mesh and painting shall be measured & paid seperately under appropriate items.

S & F in repair steel window 1.25 mm thick Box type (primer coated) ERW hollow P section of size 60 mm x 25 mm single rebated comprises glazed shutter ERW Section 50 mm x 20 mm and 1 mm thick with two open able leaf consisting two Nos of sash bars of flat iron 12 mm x 3 mm complete welded to frame with one vertical mullion of ERW box type T section of size 60 mm x 25 mm and 1.25 mm thick including cutting holes and making good dismantled portion in PCC (1:2:4) type B-1 four Nos for each window including following fitting welded to the frame shutter : (a) Hold fast 150 mm long of 12 mm x 3 mm made to shape - 04 Nos per window. (b) Handle of Z section 20 mm x 25 mm, 100 mm long 1 Nos per leaf. (c) MS tower bolt 150 mm long - 2 Nos per leaf. (d) MS pintol hings of size 100 mm x 14 mm - 2 Nos per leaf. (e) Z section 20 mm x 25 mm x 100 mm long stopper per leaf. Note : Glass and painting shall be measured & paid seperately under appropriate items.

S & F in repair steel ventilators fixed type 1.25 mm thick Box type (Primer coat) ERW hollows P section of size 60 mm x 25 mm single rebated optional full glass or wire mesh.

S&F in repairs MS 10mm bars and over for guard bars plan welded to steel window and similar articles conforming to Fe-290 Gde E- 165 complete all specified.

S&F galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanesed wire stapels complete all as specifed and directed.

S&F in repairs galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanesed wire stapels complete all as specifed and directed.

S&F in repair MS 300mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engineer-in-Charge.

S & F drapery curtain rod, mild steel, powder coated 25mm dia with brackets, knobs, end stops etc all as specified and directed by Engineer - in - Charge .

Hacking out old broken glass (any size,thickness,quality or description from metal frame including punching or drilling out old glazing pins/spring clips complete all as specified & directed by Engineer -in-charge.

S & F in 4mm thick sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.50 sqm in each pane all as specified and directed by Engineer - in-Charge.

S & F 3 mm thick pin headed sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed by Engineer - in-Charge.

S & F Magnet ball catcher for cupboard shutter, complete all as specified and directed by Engineer - in-Charge.

S & F continous (Piano)type hinges mild steel bright finish or lectro galvanised with wide of flaps 30mm complete all as spd and directed.

S & F 75mm size stainless steel bright finish handle, fancy type for cupboard shutter all as specified and directed by Engineer-in-Charge.

S&F 100 mm size hasp and staple,safety type,Stainless steel bright finish ,including bolt to hinge plate and fixed with screws,complete all as directed.

S & F fancy type 40mm dia, cupboard knobs brass polished fixed with nut, screw and washer of mild steel, bright finished etc complete all as specified and directed

Taking down cement or cement lime plaster from brick walls etc including raking out joints, hacking for key scrubbing down with water etc.

M & L 10mm thick rendering in Cement Mortar 1:3 on fair faces of brick work or concrete surfaces of ceiling finished even and smooth without using extra cement complete all as specified and directed by Engineer - in - Charge .

M & L rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finished even & smooth without using extra cement all as specified and directed by Engineer - in - Charge .

M & L rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finished even & smooth without using extra cement all as specified and directed by Engineer - in - Charge .

M&L Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 pigmented stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings .complete all as specified (Payment for providing grooves shall be made separately).

Forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden attens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge

M & L applying three coat of white wash on newly plastered or unplastered ceiling surfaces including preperation of surfaces, complete all as specified.

M & L for complete removal of existing treatment and applying two coats of white wash on old decorated plastered or unplastered surfaces of ceiling including preparation of surfaces complete all as specified and directed by Engineer - in - Charge .

Material & labour for preparation of newly plastered or unplastered surfaces of walls and applying two coats of oil emulsion distemper over chalk whiting, all as specified & directed by Engineer -in-charge.

Material & labour for preparation of old decorated (platered or unplastered) of walls and applying one coats of oil bound distemper complete all as specified & directed by Engineer -in-charge.

M & L applying two coats of cement based paint on newly plastered or unplastered wall surface including preparation of surfaces, complete all as specified.

M & L applying one coat of cement based paint on old decorated or undecorated wall surface including preparation of surfaces by washing rubbing down and stoping of distempered and painted surfaces complete all as specified.

M & L for complete removal of existing treatment and applying two coats of white wash on old decorated plastered or unplastered surfaces of walls including preparation of surfaces complete all as specified and directed by Engineer - in - Charge .

Demolation of ashlar facings, dressed stone work, stone slabs or tiles from paving and precast concrete blocks and articles all as specified.& directed by Engineer -in-charge..

M&L 18- 20mm thick granite (of any type ) work (table rubbed and polished ) in cooking platform and like in cm (1:4) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shed of granite.

M&L 18-20mm thick machine cut kota stone slab (table rubbed and polished) as in flooring laid over and including 15 mm thick screed bed or bedding layer in CM (1:4), set and jointed with grey cement slurry mixed with pigment to match the shade of slab including cutting, rubbing, grinding and mirror polishing upto desired satisfaction of Engr In Charge complete all as specfied and directed.

Cutting ,grinding ,cleaning and treating the surface of existing kota stone flooring with beeswax polishing complete as directed by Engr-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), remving serviceable tiles to stores and and rubbish off the permises.

M & L for glazed ceramic coloured tiles 7mm thick 300 x 450mm size in vertical surface set and jointed in neat cement slurry and pointed in white cement paste pigmented to the shade over and including 10mm thick cement sand plaster (1:3) complete all as specified and directed by Engineer - in - Charge.

M & L for glazed ceramic coloured tiles 7mm thick 300 x 200mm size in vertical surface set and jointed in neat cement slurry and pointed in white cement paste pigmented to tile shade over and including 10mm thick cement sand plaster (1:4) complete all as specified and directed by Engineer - in - Charge.

M&L Non skid ceramic coloured /printed tiles 7 to 8 mm thick( square /rectangular) area of each tile exc. 0.11 sqm but n. exc, 0.18 sqm and shall be jointed in neat cement slurry and pointed in paste pigmented to tile shade over and incl 15 mm th screed bed in CM 1:6 complete all as specified and directed by Engr in Charge.

M&L 75 mm thick PCC 1:4:8 type D2 using 40 mm graded aggregate as in sub base all as specified.

M&L cement concrete type B-1, 1:2:4 using 20mm graded stone aggregate as in floors 25 mm thick for tiles all as specified.& directed by Engineer -in-charge..

Demolition of cement concrete ( un re-inforced) of any description in ground floor and pavings Nexc15 cm thickness (below or above GL)

S&F in repairs stainless steel kitchen sink with drainage board of overall size 915x460mm and bowl size 410x330x160mm with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe complete all as directed.

M & L runnung welding in repairs thickness of metal exc 6mm n exc 9mm

S & F in repair powder coated aluminum sliding window three track with frame & two glass shutter using 4 mm thick glass tinted modi guard and one shutter with stainless steel wire gauge wire cloth 0.31 mm nominal dia of wire and width of aperture 1.61 mm using aluminum powder coated section aluminum cleat , PVC track, bearing, handle lock rubber beading etc complete fittings as approved. Note :- Size of aluminum section shall be under – (i) three track top and vertical – jindal main 2010. Section No 20621 or equivalent as approved by GE. (ii) Three track bottom – Jindal main – 2010 section 20620 or equivalent as approved by GE. (iii) Shutter Vertical Section - Jindal main – 2010 section 20604 or equivalent as approved by GE. (iv) Shutter top and bottom - Jindal main – 2010 section 20604 or equivalent as approved by GE. (v) Shutter vertical middle ( interlock) - Jindal main – 2010 section 20605 or equivalent as approved by GE.

S&F powder coated anodized aluminum frame for doors, windows , ventilators with one of more rebates including joining cleat for fixing etc. completed all as specified

S&F anodised aluminium frame for doors , window , ventilatores with with one or more rebate including joiing cleat forfixing etc . complete all as specified.

S&F anodised aluminium door shutter , aluminium section wt 0.55 kg / mtr including necessary joining cleats ,glazing clips, rubber eoprene packing , handles 2 Nos. in each door , hinges , anodised aluminium snap beading screws etc.

S&F anodised aluminium window / ventiletor shutter , side hung type without sash bar ,aluminium section wt 0.55 kg / mtr including necessary joining cleats , glazing clips, rubber packing , anodised aluminium snap beading screws , anodised aluminium fitting such as peg stays 150 mm long (1 No.) hingestype B-21 100mm long (2 Nos. )suitable handle (1 No) complete allas specified .

S&F anodised aluminium grill of daimond size 100x100mm of dia 6mm including necessary joining cleats , anodised aluminium snap beading screws , complete all as specified .

S & F Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specified and directed.

S&F in repairs door closer hydraulically regulated, aluminium (Die cast) body, designation No. 3, universal type suitable for door shutter upto 1000mm in width complete all as specified and as directed.

Taking down and refixing of alum window shutters of any size in same opening incl repairs /replacement of rubber packing,glass,glazing clips & aluminium section etc (The item glass,glazing clips & alum section will be measured seperately)

Taking down aluminium door shutter ,Refixing of shutters of any size in same opening incl repairs / replacement of rubber packing,glass,glazing clips & aluminium section etc after tightening of members, adjusting of door closure etc. complete all as specified and directed (The item glass,glazing clips & alum section will be measured seperately)

Taking down and refixing of rolling shutters including greasing,oiling,repairs/replacement of part of any size exc 3.00 sqm but not exc 7.5 sqm area ( the defective parts to be seperately in concern items )

Supply of 1.25mm thick MS sheet laths complete all as specified & directed by Engineer-in-charge.

Supply of MS gear pully suitable for rolling shutter of any size complete all as specified & directed by Engineer-in-charge.

Supply of tension spring suitable for rolling shutter of any size all as specified & directed by Engineer-in-charge.

Demolition of brick work or stone masonry built in cement mortar including all quoins, pillars, arches etc. but excluding ashlar facings, dressed stone work and precast concrete articles, complete all as specified and as directed.

M&L Brick work with old size burnt fly ash bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6 all as specified and directed.

S & F in repair brass chromium plated central hole basin mixer with regular spout , popup waste system and 450mm long braided hoses with connection and nuts complete all as specified and directed .

S&F sink mixer with swinging spout (wall mounted model) chromium plated brass with connection and nut complete all as specified and directed. Make-ESSESS Cat Part No DE- 12 or equivalent

S & F in repairs brass chromium plated wall mixer with non telephonic shower arrangement for mixing hot and cold water screwed down for iron pipe and fixed as directed. Make : ESS ESS Cat Part No .: TM-115 or equivalent.

S & F in repairs 15 mm bore bib tap fancy type chromium plated with crutch or butterfly handle screwed down ,screwed for iron pipe all as specified.

S&F in repairs 15mm stop valves fancy type, chromium plated ,cast copper alloy, screwed down, high pre-ssure, with crutch or but-terfly handle, screwed both ends for iron pipe or for unions and fixed.

Ditto as per item No above but fancy type, chromium plated with long shank and cup (concealed type).

S/F in repairs pillar taps 15mm bore fancy type chromium plated cast copper alloy with capstan heads scre-wed down high pressure with or without lettered hot' or'cold' with long screwed shanks and fly nuts screwed for iron pipe . ISI marked.

S & F in repairs Grating doom 125 mm dia with waste hole of PTMT ( Min wt 40 gm )

S&F in repair PVC connection both side brass unions internal for size 15mm dia and 450mm long all as specified and directed by Engineer-in-Charge.

S&F PVC waste pipe 32mm dia & 90 cm long

S & F in repairs glass corner shelf assembly fancy type made 8 mm thickn sheet glass of size 300x300mm fixed with 'F' or 'D' type brass CP brackets complete all as specified.

S & F in Repairs towel rails 16 mm dia 600 mm long superior quality brass chromium plated fancy type Complete all as specified fixed in repairs.

S & F in repairs for brass chromium plated shower rose 125 x 125 mm size with swivel joint including fixing to 15 mm dia steel pipe or union.

S&F in repairs soap dish,chromium plated, 100X100X60mm, fixed to wall with plugs with chromium plated screws complete all as specified and directed.

S&F Chromium plated health faucet 1 mtr long fixed with screws complete all as specified and directed.

S&F EWC Jet spray complete all as specified and directed.

Dismantling water tanks and removing to store of exc 250 nexc 500 ltr capacity

S & F rotational moulded polythene three layered white coloured water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part I of capacity 500 Litres all as specified and directed by Engineer - in - Charge .

Dismantling water tanks and removing to store of exc 500 nexc 1000 ltr capacity

S & F rotational moulded polythene three layered white coloured water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part I of capacity 1000 Litres all as specified and directed.

S&F in repair 20mm Ball brass valves, high pressure, with polytheene float and flynut complete, screwed for iron pipe orr brass ferrule and fixed.

S&F in repair 25mm Ball brass valves, high pressure, with polytheene float and flynut complete, screwed for iron pipe orr brass ferrule and fixed.

S&F in repair PVC low level flushing system 10 Ltr capacity with flush pipe complete as approved by Eng-in charge.

S&F in repair Viterous China squating pan Orrisa pattern size 580/440mm wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) with plastic seat cover.

S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) but including connection to drain (or outgoing pipe) and to flushing pipe, anti-syphonage pipe, sheet cover complete.

S&F in repair vitreous china,white wash hand basin ,pedestal type, flat back size 550x400mm complete all as specified and directed by Engineer-in-Charge.

S&F in repair plastic water closet seat, white closed patern withflat bottom and cover and mild steelcromium plated or aluminium hinging device

Taking down eves and gutter and rain water of any size all as specified and directed by Engineer - in - Charge .

S & F 110mm PVC (SWR) pipes and single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S&F 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S&F 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 110mm PVC(SWR) bends any radius complete all as specified and directed.

S&F 75mm PVC(SWR) bends any radius complete all as specified and directed.

S&F PVC (SWR) floor trap 100/75 mm bore with grating including jointing to waste pipe and fixed with PCC 1:2:4

S & F 100mm bore stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof all as specified and directed.

Dismantling of CI pips or reinforced concrete pipes 100 mm dia fixed to wall etc complete all as specified and directed.

Dismantling of CI pips or reinforced concrete pipes 75 mm dia fixed to wall etc complete all as specified and directed.

S&F in repairs 100 mm dia. cast iron waste and vent pipe in any length with or without ear with cement joints fixed to wall.

S&F in repairs 75mm dia cast iron waste and vent pipe in any length with or without ear with cement joints fixed in repairs to wall .

S & F in repairs CI bends 100mm dia (any radius), diminishing pieces or tapers( larger bore measured).

S & F in repairs CI bends 75mm dia (any radius), diminishing pieces or tapers( larger bore measured), with access door.

S & F in repairs CI branch pieces single 100mm dia (equal or unequal), ordinary or inverted or with parallel branches, with access door, complete all as specified.

S & F in repairs CI branch pieces single 75mm dia (equal or unequal), ordinary or inverted or with parallel branches, with access door, complete all as specified.

S&F CI 'P' or 'S' trap of 100mm size all as specified and directed by engineer-in-charge.

Taking up or down steel tubing of 15 mm bore and connections, including cleaning for re-fixing or removal to store

Taking up or down steel tubing of 20 mm bore and connections, including cleaning for re-fixing or removal to store

S&F Chlorinated PVC (CPVC) pipes 20 mm outer dia, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.0 m spacing . this includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete all as specified and directed. Make : Supreme/Vectus or equivalent

Supply & fixing mild steel tubes of size 20 mm bore (medium grade) galvanised with all fittingsand fixed complete to wall all as specified.

S&F Structural steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes grade St-240 complete all as specified and as shown on drawing.

Desmantling plain, coraugated steel sheeting any guage, thickness including nanital or similar pattern roof covering.

S&F Pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified.

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets

S & F false ceiling not less than 9 mm thick gypsum tiles (600mm x 600 mm) laminated with PVC film on the face side & metalised polyester film on the back side with all four edges sealed with PVC film (shade either plain white or crack) fixed using T grid/Cross-T/Wall angle/level clip & suspenders/hangers 4 mm dia. GI wire (upto 1200 mm length) adjusting level fixed to roof slabs/trusses complete all as specified and as directed by Engineer-in-Charge. Make : Saint Gobain / Armstrong/Everest

S&F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for.

M & L RCC 1:1½:3, (nominal mix), Type A-1, using 20mm graded aggregates as in chajjas, fins, fascias,shelves , louvers, parapets and railing etc and the like including necessary formworks all as specified and directed by Engineer - in - Charge.

S&F TMT bars 10mm dia and over, cut to length, bent to shape required,including binding with mild steel wire (annealed) not less than 0.9mm dia.

M & L for providing and injecting chemical emulsion for post constructional antitermite treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.50 Ltrs per Sqm of the vertical surfaces of the sub-structure to a depth of 300 mm including excavating channel along the wall and rodding etc. complete all as specified and directed. Note : Quantity will be measured perimeter of wall x depth of penetration.

MANCHANDA CONSTRUCTION CO

A R CONSTRUCTION COMPANY