8893 SPECIAL REPAIRS TO BLDG NO P-02 AT HBTC MARVE UNDER GE NORTH MUMBAI

Amount

CIVIL WORKS Material and labour for surface preparation of structural part by gentle chipping by manually to make the surface rough and thoroughly cleaned with air as per standard practice and directions of Engineer-in-charge (including removal of external plaster, wherever exists) costs inclusive of transportation, labour, conveying debris away from the site (max 50m) tools and tackles, lead and lift etc, complete all as specified and as directed by Engineer-in-Charge.

Supply and fix CRS (Corrosion resistant steel), 10mm dia and over cut to length bent to shape required including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge. Note: Cutting of rusted reinforcement & welding shall be inclusive in this item of work

Supply and fix CRS (Corrosion resistant steel), 8 to 10mm dia in stirrups, spacers and binder cut to length bent to shape required inch cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge. Note: Cutting of rusted reinforcement & welding shall be inclusive in this item of work

Demolition of reinforced cement concrete of any description in any position including necessary scaffolding arrangement (reinforcement cut as required to facitate demolition) and removing concrete debris and depositing outside MD land all as specified and as directed by Engineer-in-Charge. Note : Reinforcement obtained from this item shall be handed over to contractor on account of sch of credit

Supply and fix MS/TS dowel pins/staple/shear pins including drilling holes in concrete and providing labour and but excludes the materials for grouting the pins.etc complete all as specified and as directed by Engineer-in-Charge.

Repairing of excessively damaged concrete portion by using super fluid dual shrinkage compacted and providing, casting with micro concrete of grade M-40 at all levels with all leads and lift as directed including mixing, laying, levelling, finishing including curing and formwork of steel or marine ply complete all as specified and directed by Engineer-in-Charge. Make: Fosroc / SIKA / BASF / Krishna Conchem or equivalent approved .

Material and labour Reinforced cement concrete 1:11/2:3, type A-1 (nominal mix) using 20mm graded stone aggregate as in slabs supported on walls, beams and columns, in floors, roofs, landings, balconies, canopies etc. complete all as specified and as directed by Engineer-in-Charge.

Material and labour for formwork of to pour the micro concrete/concrete using steel shutters or 12mm marine ply to have the form finish including de-shuttering etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for providing and applying rust cleaner (Re-backler solution) to exposed corroded reinforcement @ 0.20 Litre/Sqm or approved make over prepared reinforcement, including removing concrete all around reinforcement including from behind the reinforcing bars by manual methods such as hammering the rebar, using wire brushes, chiselling, etc. and applying rust removing solution of approved make with cotton waste swab to reinforcements etc. complete as directed by Engineer-In-Charge.

Material and labour for providing and applying two coats of anticorrosive epoxy phenolic rebar protective system IPNet RB or equivalent of approved make and quality comprises of resin and hardener mixed in equal proportion by volume with minimum 9-10 hours between the coats, sprinkling dry sand when 2nd coat is tacky so as to provide rough finish and ensuring air curing of minimum 10 hours after the top coat before any subsequent treatment etc. including scaffolding etc complete all as specified and as directed by Engineer-in-Charge. NOTE:- New Reinforcement shall be measured and paid separately under respective item. (b) Cost of welding deemed to be inclusive in this item of work.

Material and labour for providing and applying a priming cum bonding coat of two component Epoxide Resin conforms to ASTM-C-882-91 of approved make and quality to clean and sound concrete area by brush or any other established method by mixing Base and curing agent in 2:1 proportion by weight for joining old and new concrete as per technical specifications of manufacturer. Work shall be carried out as per the manufacturers specifications & certificate on this account shall be taken from consultant and as approved by Engineer-in-charge

Material and labour Drilling and fixing teflon nozzles in RCC members, including drilling holes (drilling 12 mm dia, 40mm deep holes in structural members at the intervals of 600mm c/c in staggered manner or s directed by Engineer-in Charge in RCC structure elements and cleaning the holes (to clean the holes by air blower prior to fixing nozzles) and fixing of nozzles (to insert 12mm dia teflon nozzles in cleaned holes external end of nozzles (to insert 12mm dia teflon nozzles in cleaned holes external end of nozzles to be machined to receive outlet of grouting gun and fixing it inside the holes by applying thixotropic epoxy putty to ensure complete sealing and curing the system for minimum 12 hrs) and cutting of nozzles (to cut the nozzle by chisel after completion of grouting without damaging structural elements etc complete all as specified and as directed by Engineer-in-Charge.

Injecting low viscosity (3-5 cps) high molecular weight monomer by pressure and using mechanized injector gun with accessories, till nozzles refuses to accept the grout, Including, Mixing of materials( Mixing material components (part a & b) in required quantities as per manufacturer’s instruction by weigh batching) and Grouting ( Filling the grouting gun with monomer. Maintain desired pressure in the gun by air compressor; maintain the pressure at exit (4 to 5 Kg/ Cm2) by monitoring pressure gauge at exit. Grouting the material through prefixed nozzles in the structural elements till its refusal. Sealing the nozzle with epoxy putty after the refusal. Monitoring leakages through other nozzles while grouting and seal them as per the requirement. Repeat the process for all the nozzles. the operation to be within pot life of the material.)and Cleaning of gun and accessories ( the gun and accessories like valves, pipes and other fixtures to be cleaned with thinner after the operation to avoid jamming of the gun.) etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for providing and laying 20 mm thick POLYMER MODIFIED MORTER over identified R.C.C. members in One layer in proportion of 1:5:15 by weight of polymer of approved make, cement and filler material of approved make, blended to a required consistency and applying and finishing by floating, curing after initial setting time, including providing and inserting 10 mm mild steel shear key bars (minimum 3 nos per sqm), wherever required, bonding slurry, etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Strengthening structural elements with non metallic composite fiber wrapping system comprise of uni-directional carbon fiber sheet (430 GSM) and compatible saturant Profiling, applying compatible primer on prepared substrate, Filling the holes and uneven surface with thixotropic epoxy putty etc. , complete mechanized wetting of fiber sheet, cutting the fabric to required size, mixing of saturant and filling in tub area of the saturation machine, placing the fiber on metallic rods and pass through the rollers of machine and saturant tub ensuring complete wetting (65% fiber volume fraction) of fibers, removing the fiber on rod and placing the new fiber sheet, wrapping the fiber sheet to structural element at desired orientation using tamping roller to avoid any air voids etc., repeating the same procedure for multiple layer with the interval of 8 hrs ,applying second coat of saturant after minimum 12 hrs after first coat, rectify air voids including sprinkling of sand and finally rendering with10mm thick in CM 1:6 including finishing even & smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge. Mode of measurement- Per sq.mt of surface area of carbon fiber sheet without lapping. Make: FOSROC/FIXIT/Krishna Conchem/ Sika

Providing and fixing carbon fiber anchor including drilling hole in the base concrete, fixing the anchor using epoxy 50X55 system, spreading the anchor fibers in star pattern including application of saturate complete all as specified and as directed by Engineer-in-Charge. Note for Item No.1 to 16:- (i) The work under Item No. 1 to 16 shall be carried out by authorised applicator only. (ii) Defect liability for these items shall be 5 years from certified date of completion. (iii) Amount of 5% of these items shall be retained during RAR and FB. This amount shall be released after successful completion of Defects liability period as mentioned above. (iv) Non destructive testing shall be got carried out through IIT / NIT / College of Engineering Pune to decide fulfilment of fitness criteria of structure. (v) The test shall be carried out at each discrete location or locations decided by GE or testing authority. (vi)The cost of testing shall be deemed to be included in the rate quoted by the contractor. Completion shall be issued by GE after only getting structural stability certificate of each respective building from testing authority.

Demolition of brick work/stone/PCC block masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars, PCC coping etc, but excluding ashlar facings, dressed stonework and precast concrete articles and removing of debris outside MD land complete all as specified and as directed by Engineer-in-Charge.

Material and labour for brick work with sub class "B" bricks straight or curved on plan exceeding 6 mtr mean radius with old size bricks and built in cement mortar (1:6) complete all as specified and as directed by Engineer-in-Charge

Material and labour for brick work built in cement mortar 1:4 using sub class 'B' bricks, straight or curved on plan to any radius as in half brick thick wall all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for etc complete all as specified and as directed by Engineer-in-Charge.

Dismantling Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings including ridges all as specified and as directed

Material and labour for Rolled mild steel sections as in joist, channel, angle, or tee sections, without connecting plates, etc to form frame complete all as specified and conforming to Fe - 410 W (Grade E-250) 'A' quality complete all as specified and as directed by Engineer-in-Charge.

Supply and fix Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick as per approved profile of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or L type or J type or cranked hook bolts or as per manufacture instruction complete all as specified and as directed by Engineer-in-Charge. Make: JINDAL / INDALCO / HINDALCO / ASSOCIATED Profiles and Aluminium Ltd / ESSAR colour coated sheets

Supply and fix Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick as per approved profile of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or L type or J type or cranked hook bolts or as per manufacture instruction complete all as specified and as directed by Engr-in-Charge. Make: JINDAL / INDALCO / HINDALCO / ASSOCIATED Profiles and Aluminium Ltd / ESSAR colour coated sheets

Material and labour for preparation of new steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer with necessary scaffolding / shuttering etc complete all as specified and as directed. Make : Asian paints/ Nerolac paints/Berger paints/ Shalimer paints/ Dulux

Material and labour for preparation of old painted steel surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge. Make : Asian paints/ Nerolac paints/Berger paints/ Shalimer paints/ Dulux

Taking down cement plaster on brick or stone walls including ceilings etc., including racking out joints, hacking for key scrubbing down with water all as directed.

Material and labour for rendering 10mm thick on internal wall surfaces using factory manufactured pre mix/ready mix plaster of 'Roofit Mix' of M/s Premier Floor to Roof Materials Pvt Ltd/'Easy plast' of M/s Walplast Products Pvt Ltd/'Readiplast' of M/s Ultratech Cement Ltd' / Soundplast PMC-1 of M/s Sound buildcare Pvt Ltd/or other approved equivalent make, having minimum composition of C:S : 1:6 using fully treated dry, well graded natural sand confirming to IS 383 suitable for plastering, having low rebound properties, low water demand for curing properties mechanical mixing with water in a metallic tray only to make good consistency as per the specification of the Manufacturer and applied over masonry and concrete surfaces and finishing with sagol finish not less than 1mm thick, including cleaning the surfaces, curing etc complete all as specified & directed by Engineer-in-Charge.

All as per item No.28 but of 5mm rendering of minimum composition of C:S 1:4 on ceiling and finishing surfaces complete all as specified and as directed by Engineer-in-Charge

Material and labour for rendering 15 mm thick cement plaster in CM 1:4, two coats using factory manufactured pre mix/ready mix of 'Roofit Mix' of M/s Premier Floor to Roof Materials pvt.ltd/ 'Easy plast' of M/s Walplast Products pvt.ltd/ 'Readiplast' of M/s Ultratech Cement Ltd/'Soundplast PMC-1' of M/s Sound buildcare pvt.Ltd/ or other approved equivalent make, having minimum composition of C:S :1:4 using fully treated dry, well graded natural sand conforming to IS 383 suitable for external plastering, having low rebound properties, low water demand for curing properties, mechanical mixing with water in a metallic tray only to make good consistency as per the specification of the Manufacturer and applied over exterior masonry and concrete surfaces with base coat of 10 mm thick and finishing coat of 5 mm thick final rendering with water proofing compound @ 3% by weight of cement or as per manufacturer's instructions, including using richer mix for making corners if necessary, at all floors and level, including making grooves of existing size wherever required, including cleaning the surfaces, curing including provide of 150mm chicken wire mesh fixed with nails at the junction of RCC columns/walls/ beams/ lintels and brick masonry at external faces before plastering including scaffolding at any height and all safety materials required for execute work etc complete all as specified and as directed by Engineer-in-Charge.

Supply only integral water proofing compound ISI marked complete all as specified and as directed by Engineer-in-Charge. Make : Pidilite Industries Ltd, Taloja /Super Aquacem (India) Ltd /FOSROC/Siko/Dr Fixit

Material and labour for opening out cracks in wall surfaces in 'V' shape by mechanical grinder and removing the loose material. filling with crack filler of Dr. Fixit crack-X, shrink-free or equivalent all as per manufacturer's instructions and finishing the surfaces to match with existing finish complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of new plastered surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified and directed by Engineer in Charge. Make: Asian Paints (Tractor) / Nerolac Paints /Jenson & NIcholson / Shalimar Paints

Material and labour for preparation of new plastered surfaces on ceiling and applying two coats of Distemper oil emulsion over a coat of priming plastered and other surfaces with alkali resistant priming paint on ceiling complete all as specified and as directed by Engineer-in-Charge. Make: Asian Paints (Tractor) / Nerolac Paints /Jenson & NIcholson / Shalimar Paints

Material and labour for preparing new plastered surfaces and applying two coats of Acrylic weather proof coat 100 % exterior grade paint over one coat of acrylic primer on wall surfaces complete all as specified and as directed by Engineer-in-Charge and as per manufacturers instructions. Make: Asian Paints / Nerolac Paints /Berger paints / Shalimar Paints

Material and labour for preparation of new plastered surfaces of wall , and applying two coat of plastic emulsion paint over a coat of primer complete all as specified and as directed by Engineer-in-Charge. Make: Asian Paints / Nerolac Paints /Berger paints/ Shalimar Paints

Material and labour for complete removal of existing treatment and applying two coats of distemper oil emulsion over a coat of alkali resistant primer over 1.5mm wall care putty including preparation complete all as specified and as directed by Engineer-in-Charge. Make: Asian Paints (Tractor) / Nerolac Paints /Jenson & NIcholson / Shalimar Paints

Material and labour for preparation of old painted surfaces of wall , and applying two coat of plastic emulsion paint over a coat of priming paints over thin layer of wall care putty on wall complete all as specified and as directed by Engineer-in-Charge. Make: Asian Paints / Nerolac Paints /Berger paints/ Shalimar Paints

Material and labour for complete removal of existing treatment on wall and applying two coats of Acrylic weather proof coat 100 % exterior grade paint over one coat of acrylic primer on wall surfaces complete all as specified and as directed by Engineer-in-Charge and as per manufacturers instructions. Make: Asian Paints / Nerolac Paints /Berger paints / Shalimar Paints

Taking down chowkats or frame with shutters, not exceeding 1.5 sqm each (without taking off shutters from the frames) including all fittings & removing clear off site after credit for the same is recovered by dept complete all as specified and as directed by Engineer-in-Charge

Taking down chowkats or frame with shutters, exceeding 1.5 sqm but not exceeding 4.00 sqm each (without taking off shutters from the frames) including all fittings & removing clear off site after credit for the same is recovered by dept complete all as specified and as directed by Engineer-in-Charge

Taking down shutter carefully, area exceeding 1.sqm but not exceeding 2sqm each including all fittings & removing clear off site after credit for the same is recovered by dept complete all as specified and as directed by Engineer-in-Charge

Supply and fix solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with 19mm x 19mm MS square tube EPDM rubber gasket weather seal to be provided through the frame, the profile shall be mitre cut at two corners and jointed by inserted 2mm of 150mm long bracket of 15mm x 15mm MS square tube inside the 19mm x 19mm MS square tube and suitable screwed the door frame shall be fixed to the wall using PVC fasteners. A minimum of 6Nos screws to be provided for each frame all as specified and as directed. Note: The quoted rates are deemed to be included for cutting holes, providing concrete for hold fast and making good to the disturbed surfaces. Make : RAJSHRI / SINTEX / TUFFFLON / M/s Navratan Specialty Chemical LLP – ‘Brand : GIZA’

Supply and fix factory made solid panel PVC door shutter 30mm thick (style) consisting of frame, made out of M. S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC `C` channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, fixing in the frame at site as per specification & drawing on Serial Page No 156 of SSR Part II (pertaining to item No 08080) complete all as specified and as directed by Engr-in-Charge. Make : RAJSHRI / SINTEX / TUFFFLON / M/s Navratan Specialty Chemical LLP – ‘Brand : GIZA’

Supply and fix plain solid straight chowkats, second class hardwood, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints including making good frame in cement concrete complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparing surfaces of wood and wood based materials, steel and iron work, treating ends of posts, hold fasts, backs of chowkats, etc., area tarred exceeding 0.1sqm not exceeding 0.5 sqm each and treated with tar or coal tar black paint complete all as specified and as directed by Engineer-in-Charge.

Supply and fix mild steel hold fast confirming to Fe 290 grade E-165 complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Plain cement concrete 1:3:6, type C-1, using 20mm graded aggregate for fixing hold fasts/ refilling in floor cutting with necessary plaster complete all as specified and as directed by Engineer-in-Charge.

Supply and fix 35mm thick factory made plain framed panelled shutter 2nd class hardwood rail and style (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS-1003 (Part-I) kiln seasoned and chemically pressure treated complete all as specified and as directed by Engineer-in-Charge. Make : M/s Goel Brothers, Raipur / M/s Pioneer Timber, Chandigarh / M/s Goyal Industries, New Delhi / M/s Jain Doors pvt Ltd, Haryana / M/s India Wood & Wood Pdts, Mangalore / M/s MP Wood Products, Indore / M/s A1 Teak Products, Indore / M/s Jain Wood industries( Brand : JAYNA)

Supply and fix 35mm thick factory made 2nd class hard wood glazed and skeleton shutter, open rebated, prepared to receive glass, gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of members of shutter as specified in SSR Part-I section 8, clause No 8.24 (b) complete all as specified and as directed by Engineer-in-Charge. Make: M/s Goel Brothers, Raipur / M/s Pioneer Timber, Chandigarh / M/s Goyal Industries, New Delhi / M/s Jain Doors pvt Ltd, Haryana / M/s India Wood & Wood Pvts, Mangalore / M/s MP Wood Products, Indore / M/s A1 Teak Products, Indore / M/s Jain Wood industries( Brand : JAYNA)

Supply and fix in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples to aluminium windows and wooden door shutters etc complete all as specified and as directed by Engineer-in-charge.

Supply and fix extruded aluminium alloy handles fabricated types, anodised, of size 150 mm long complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix stainless steel butt hinges, medium weight, 100mm size all as specified and directed. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix aluminium anodised barrel tower bolt of extruded section size 150mm complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix aluminium anodised barrel tower bolt of extruded section size 200mm complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix aluminum anodized sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminum alloy 250mm long, ISI marked complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix aluminum anodized sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminum alloy 300mm long, ISI marked complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring 140mm size, complete all as specified and as directed. Make : Classic/ Shalimar/ CLIF/ARGET

Material and labour for preparing new wooden surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by Engineer-in-Charge. Make: Asian Paints/Nerolac Paints/Berger Paints/Shalimar Paints

Material and labour for preparing old wooden surfaces of any description, over 10 cm width or girth, and applying one coats of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge. Make: Asian Paints / Nerolac Paints /Berger paints / Shalimar Paints

Supply and fix 15 micron coloured aluminium sections for sliding or openable windows, ventilators, doors, partitions etc including fabrication of frame & shutters and fixing with necessary lugs, cleats, rollers, handles, locking arrangement etc including all accessories such as glazing clips and rubber beadings for fixing glass panes / wire mesh in frame complete all as specified and as directed by Engineer-in-Charge. Make : Hindalco/Indal (Indian Al Coy)/Jindal/Associated Profile & Aluminium Ltd/Ajit India Note: (i) Glass panes /wire mesh will be measured & paid separately. (ii) Rubber beading will not be weighed.

Supply and fix 4.0mm thick black sheet glass, in square exc 0.5 Sqm in each pane, fixed in aluminium windows complete all as specified and as directed by Engineer-in-Charge. Make : Modiguard/Atul/Kohinoor/Swastik/Saint Gobain

Supply and fix 4.0mm thick figured glass, in square exc 0.5 Sqm in each pane, fixed in aluminium windows complete all as specified and as directed by Engineer-in-Charge. Make : Modiguard/Atul/Kohinoor/Swastik/Saint Gobain

Supply and fix 5.5mm thick black tinted glass, in square exc 0.5 Sqm in each pane, fixed in aluminium windows complete all as specified and as directed by Engineer-in-Charge. Make : Modiguard/Atul/Kohinoor/Swastik/Saint Gobain

Supply and fix Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and as directed by Engineer-in-Charge Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix in repairs 15 micron coloured aluminium anodised grill of design No DG-101, 10 mm thick, cut to required size/shape, and fixed in position with and including aluminium beading and frame complete all as specified and as directed by Engineer-in-Charge. Make: DECOGRILLE of Associated group or equivalent make as approved by GE

Dismantling floor hearth or wall tiling including cement mortar bedding ( but not backing), removing serviceable tiles to store and rubbish out side MD land complete all as specified and as directed by Engineer-in-Charge.

Demolition of cement concrete in ground floors and pavings, not exceeding 15cm thickness (below or above ground level complete all as specified and as directed by Engineer-in-Charge

Material and labour for 75mm thick PCC (1:4:8) type D2, (using 40mm graded stone aggregate) as in sub base, finished even and rough complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 75mm thick Plain Cement Concrete (1:3:6) type C2, nominal mix (using 40mm graded stone aggregate) as in plinth protection & finished even and fair without using extra cement complete all as specified and as directed by Engineer-in-Charge.

Material and labour for non skid coloured ceramic tiles, 7 to 8mm thick (square/rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors and jointed in neat cement slurry and pointed in colour cement to match including backing coat 15 mm in CM (1:6) complete all as specified and as directed by Engineer-in-Charge. Make : Johnson Marbonite/Kajaria/Somany/Euro tiles

All as per item No.71 but in skirting/dado including 10mm thick CM 1:4 rendering of backing layer complete all as specified and as directed by Engineer-in-Charge

Material and labour for light shade vitrified ceramic tiles of size 600 x 600x 10mm thick in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match the coloured tiles including screed bed 15mm thick in cement mortar (1:6) etc complete all as specified and as directed. Make : Johnson Marbonite/Kajaria/Somany/Euro tiles

Material and labour for light shade, vitrified tiles, 10mm thick (minimum), (square/ rectangular) polished, area of each tiles not exc exceeding 0.36 Sqm (including 600mmx600mm size), on vertical surface set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, over and including 10 mm thick backing coat in cement mortar 1:4 complete all as specified and as directed by Engineer-in-Charge Make : Johnson Marbonite/Kajaria/Somany/Euro tiles

Material and labour for joint free, coloured glazed ceramic tiles of size 350mm x 250mm x 7 mm thick/ 450mm x 350mm x 7mm , on vertical surfaces etc., set and jointed in neat cement slurry and pointed in coloured cement to match over & including cement plaster 10mm thick in CM (1:4) complete all as specified and as directed by Engineer-in-Charge. Make : Johnson tiles/Kajaria/Somany/Nitco tiles

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. laid dry or laid dry and pointed complete all as specified and as directed by Engr-in-Charge.

Material and labour machine pressed precast concrete interlocking paver block of any shape and size conforming to IS 15658-2006 of 60mm thickness, M-35 grade with grey cement and pigment with glossy finish including 25mm sand cushioning complete all as specified and as directed by Engineer-in-Charge. Make: Mehtab Tiles/Indore/M/S Ultra Tiles/NITCO/Topaz Tiles/Navya Tiles Jodhpur

Material and labour for factory made, Precast, cement concrete (1:2:4) type B-1, using 20mm graded stone aggregate in kerb stone of size 300mm x 400 x 100mm in required shape finished smooth, set in cement mortar 1:4 including excavation earth work in any type of soil complete all as specified and as directed by Engineer-in-Charge. Make: Mehtab Tiles/Indore/M/S Ultra Tiles/NITCO/Topaz Tiles/Navya Tiles Jodhpur

Material and labour 18 to 20 mm thick machine cut , grinded and polished, mushroom granite stone, bedded and jointed as in steps, jambs, pillar, window cills, cooking platform and like in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match complete all as specified and as directed by Engineer-in-Charge.

Material and labour Rounding the edges of stone slab as in steps, cooking platform and similar situations complete all as specified and as directed by Engr-in-Charge.

Material and labour machine cut Kota stone slab for flooring 20-25 mm thick over cement screed bed 20 mm in CM (1:4) base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and rounding to edges complete all as specified and directed by Engineer in Charge.

Material and labour machine cut Kota stone slab for staircase tread 20-25 mm thick over cement screed bed 20 mm in CM (1:4) base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, providing two nos of grooves and rounding to edges complete all as specified and directed by Engineer in Charge.

Material and labour machine cut Kota stone slab for staircase riser (should be one piece) 20-25 mm thick over cement screed bed 10 mm in CM (1:3) base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, providing two nos of grooves and rounding to edges complete all as specified and directed by Engineer in Charge.

Supply and fix in repairs GI tubing, medium grade, 15 mm bore with all fittings and connections and fixing to walls, ceiling or laid in floors and making good disturbed surfaces using with cement mortar 1:3 all as specified and directed. Make: Tata / Jindal / Zenith / Swastik / Prakash

Supply and fix in repairs GI tubing, medium grade, 20 mm bore with all fittings and connections and fixing to walls, ceiling or laid in floors including cutting chases in brick walls pinning in and making good disturbed surfaces using with cement mortar 1:3 all as specified and directed. Make: Tata / Jindal / Zenith / Swastik / Prakash

Dismantling of 110mm cast iron/PVC pipe including bends/branch pipe jointed in cement mortar and taking out if required complete all as specified and as directed by Engineer-in-Charge

Dismantling of 75mm cast iron/PVC pipe including bends/branch pipe jointed in cement mortar and taking out if required complete all as specified and as directed by Engineer-in-Charge

Supply and fix UPVC (SWR) single socketed rain water/soil waste pipes, type B, with rubber ring joints, 110mm dia, fixed to walls complete all as specified and as directed by Engineer-in-Charge. Make : Prince / Supreme / Finolex

Supply and fix UPVC (SWR) single socketed rain water/soil waste pipes, type B, with rubber ring joints, 75mm dia, fixed to walls complete all as specified and as directed by Engineer-in-Charge. Make : Prince / Supreme / Finolex

Supply and fix UPVC (SWR) bends any radius, 110 mm bore complete all as specified and as directed by Engineer-in-Charge Make : Prince / Supreme / Finolex

Supply and fix UPVC (SWR) bends any radius, 75 mm bore complete all as specified and as directed by Engineer-in-Charge Make : Prince / Supreme / Finolex

Supply and fix UPVC (SWR) branch piece Single Y equal or unequal, 110 mm bore complete all as specified and as directed by Engineer-in-Charge Make : Prince / Supreme / Finolex

Supply and fix UPVC (SWR) branch piece double Y equal or unequal, 110 mm bore complete all as specified and as directed by Engineer-in-Charge Make : Prince / Supreme / Finolex

Supply and fix UPVC (SWR) branch piece single T equal or unequal, 110 mm bore complete all as specified and as directed by Engineer-in-Charge Make : Prince / Supreme / Finolex

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc., applying neat cement slurry @ 3kg of cement per square metre complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 40mm thick (average thickness) PCC (1:2:4), type B1, using 20mm graded stone aggregate as levelling course, laid to slope as required and finishing even & fair without using extra cement complete all as specified and directed by Engineer-in-Charge.

Material and labour for 10mm thick rendering with cement mortar 1:3 on roof slab/canopies/chajjas with water proofing compound at 3% weight of the cement as per manufacture instructions and make surfaces to receive water proofing treatment finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge. Note : Water proofing compound will be measured and paid separately

Material and labour preparation of surfaces by removing bitumen based water proofing treatment completely removed by mechanical scarification or by any other effective mechanical means and prepare the normal surface thoroughly by cleaning , washing and removing dust, dirt oil, grease, any loose particles etc and applying one coat of Dr FIXIT prime seal diluted with water in the ratio 2:1 and dry minimum 2-3 hours and apply Dr FIXIT new coat in three coats at the rate 0.50 litre per sqm in each coat and dry 6 to 8 hrs after each coat with and including laying woven glass fibre mesh 2-5 mm x 2.5mm between first coat and second coat complete all as specified and directed by Engineer-in-Charge.

Material and labour for applying two coats of flexible polymer acrylic water proofing coating, 1mm thick (Dry film in two coats) using Dr Fixit pidifin 2K of M/S Pidilite Industries or equivalent including necessary pond testing in sunken portion complete all as specified and directed by Engineer-in-Charge.

Supply and fix 32mm GI pipe medium grade as in spout n.exc 1.00 Rm each (in short length) complete all as specified and as directed by Engineer-in-Charge. Make: Tata/Jindal/Zenith/Swastik/Prakash

Material and labour for Plain cement concrete 1:5:10 Nominal mix type E2 using 40mm graded stone aggregate as in sunken floor complete all as specified and as directed by Engineer-in-Charge.

Supply and fix in repair 32mm bore low density polyethylene pipes(LDPE) of pressure rating 6 kg/ cm2 complete all as specified and as directed by Engineer-in-Charge. Make: Finolex/Prince/Kisan/Supreme/SFMC

Supply and fix in repairs UPVC floor trap 75mm outer dia with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) etc, complete all as specified and as directed by Engineer-in-Charge. Make : Prince / Supreme / Finolex

Supply and fix in repairs 15mm bore bib taps, fancy type, chromium plated, cast copper alloy, long body with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule all as specified and as directed.

Supply and fix in repairs concealed type stop valve, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes or for unions of 15mm bore complete all as specified and directed by Engineer-in-Charge. Make : Soma/Leader/Zoloto/Prayag

Supply only 15mm bore CP pillar taps, fancy type, cast copper alloy, with capstan heads, screwed down high pressure, with or without lettered 'hot or cold' with long screwed shanks and fly nuts screwed for iron pipe complete all as specified and as directed by Engineer-in-Charge. Make : Jaguar/Soma/Leader/Zoloto/Prayag

Supply and fix in repairs aluminium anodised tubular towel rail, 20mm dia, D type, 60cm long, between flanges including suitable bracket complete all as specified and as directed by Engineer-in-Charge. Make : Crown / Jindal / Essess / Swastik

Supply and fix in repairs Swivel shower of PTMT, any colour, for fixing with 15mm pipe, minimum weight 40gms complete all as specified and as directed by Engineer-in-Charge. Make : Jaypee/GMP/Zoloto/Neta/Prayag/Symet/Polytuf

Supply and fix in repairs PTMT Liquid Soap container fixed and including chromium plated brass screws with wooden/plastic cleats complete all as specified and as directed by Engr-in-Charge. Make : Jaypee/GMP/Zoloto/Neta/Prayag/Symet/Polytuf

Supply and fix in repair vitreous china squatting pan Orissa pattern of size 580 x 440mm white with integral foot rest, 'P' or 'S' trap front and back inlet and including connection to trap and to flushing pipe, anti syphonage pipe etc (excluding flushing cistern & flush pipe) & provision of Plain cement concrete 1:5:10 nominal mix type E2 using 40mm stone aggregate all as specified and as directed. Make : Cera/Hindustan/Parryware/Jaguar/Hindware/Johnson

Supply and fix in repairs vitreous china wash down, white, water closet pan (pedestal pattern) with 'P' of 'S' trap (of size 465mm x 355mm x 265mm), including plastic seat cover to match with colour of WC, closed pattern with flat bottom & cover and chromium plated mild steel or aluminium anodized hinging device including connecting to trap and flushing pipe, anti-syphonage pipe etc complete all as specified and directed by Engineer-in-Charge. Make : Cera/Hindustan/Parryware/Jaguar/Hindware/Johnson

Supply and fix in repairs PVC valveless, syphonic action type low level flushing cistern 10 ltr capacity white with inlet ball valve, float and handle including brackets and connection to pipes and fixing of chain and pull or lever complete all as specified and as directed by Engineer-in-Charge. Make : Cera/Hindustan/Parryware/Jaguar/Hindware/Johnson

Supply and fix in repairs flush pipe of polyethylene of low or high density of PVC 32mm dia for low level cistern all as specified and as directed by Engineer-in-Charge. Make : Jaypee/GMP/Zoloto/Neta/Prayag/Symet/Polytuf

Supply and fix in repair vitreous china bowl urinal, flat back, size 465 x 355x 265 mm white (minimum), with grating and urinal for discharge pipe, waste pipe complete including providing and fixing plugs, bedding urinal against wall in CM securing urinal to plugs with and including 60mm long brass screws, pointing around, fixing cistern with brackets, flush pipe grating and union for discharge pipe complete all as specified and as directed by Engineer-in-Charge. Make: Parryware/Cera(Istquality)/Jaguar/Hindware/Johnson

Supply and fix in repairs, UPVC Nahani trap,75mm dia with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) etc, complete all as specified and as directed by Engineer-in-Charge.

Supply and fix in repair PTMT grating doom over Nahani trap and floor trap of 100mm Dia complete all as specified and directed by Engineer-in-Charge. Make : Jaypee/GMP/Zoloto/Neta/Prayag/Symet/Polytuf

Supply only PVC connection,15 mm size with PTMT nuts, of length 450 mm complete all as specified and as directed by Engineer-in-Charge. Make : Jaypee/GMP/Neta/Zoloto/Prayag/Symet

Supply and fix in repairs vitreous china wash hand basin, white, flat back of size 550 mm x 400 mm excluding taps, waste chain and plug and porcelain stopper including brackets, chromium plated waste coupling, waste fitting etc, cutting for and pinning in ends of brackets, connecting to supply and waste pipe complete as specified and directed. Make : Cera/Hindustan/Parryware/Jaguar/Hindware/Johnson Note:- Pillar taps, waste fittings, PVC connection, PVC waste pipe shall be measured and paid separately as "Supply only

Supply only 32mm, waste fittings, brass chromium plated for glazed ware sink, basins, etc. with long screw shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and as directed by Engineer-in-Charge. Make : Soma/Leader/Zoloto/Prayag

Supply only PVC waste pipe 32mm bore of size 450mm to 600mm long complete all as specified and as directed by Engineer-in-Charge.

Supply and fix in repair rotational moulded polyethylene water storage tanks 1000 litres capacity with inlet connections, three layer (cylindrical or vertical with closed top) HDPE with ISI marked, hoisted and fixed in position either inside or out side of the building, connecting up pipes securing access covers etc complete all as specified and directed by Engineer-in-Charge Make : Sintex/Polycon/infra/Rotex

Supply and fix in repairs gun metal gate valve 20mm bore with iron wheel head, screwed both ends for iron pipeSupply and fixixed including taking down existing etc complete all as specified and as directed by Engineer-in-Charge. Make: Kirloskar / Zoloto / Kartar / Upadhaya / Leader / BIR

Supply and fix in repairs Ball Valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed of 15 mm bore complete all as specified and as directed by Engr-in-Charge (Minimum weight - 142 gms) Make : Jaypee/GMP/Neta/Zoloto/Prayag/Symet

Dismantling Wall lining boards, any thickness, including cover fillets complete all as specified and as directed by Engineer-in-Charge.

Supply and fix Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame complete all as specified and as directed by Engr-in-Charge. Make : M/S Rajshri Plastiwood, Indore/M/S Sintex Industries Ltd/M/S Accucell/M/S Dura Plast Extrusion

Material and labour for applying 1.5mm thick wall care putty over surfaces complete all as specified and directed by Engineer-in-Charge. Make : Birla cement/JK white/ Golden Mohar

Material and labour for applying 1.5mm thick exterior grade wall care putty over surfaces complete all as specified and directed by Engineer-in-Charge. Make : Birla cement/JK white/ Golden Mohar

E/M Works Taking down carefully copper / aluminium point wiring (light, fan, socket or power) complete including fittings such as switches, ceiling roses, pendants, regulators, sockets etc., removing materials out side MD land in case of Credit and making good disturbed surfaces of walls, floors, etc., all as specified and as directed.

Material and labour for Point wiring complete with PVC insulated FRLS cable 1100 volts grade with multi stranded copper conductor conforming to IS-694, 1.5sqmm (nominal area) drawn through and including non metallic rigid PVC casing / capping (ISI marked, not lessthan 20mm wide) and accessories on surface of wall/roof with sunken type pressed steel/welded terminal boxes made out of 1.6mm mild steel sheet, 3mm thick laminated sheet cover for mounting of switches, socket outlets, regulators etc., including provision of PVC insulated FRLS cable 1100 volts grade with multi stranded copper conductor 1.5sqmm as earth continuity conductor and connecting to common earth dolly complete all as specified and as directed for the following: Make:Plaza/Finolex/Anchor/Havells/Nicco/Polycab/RPG

One light/fan/bell point controlled by one, one way switch

One 3 pin 5 Amps switch socket point on independent board.

One 3 pin 5 Amps socket combination point in the same board with other switches

One light point controlled by two way switch

All as per item No. 130 described here - in - before but for 3 pin 15 Amps switch socket on independent board with 2.5sqmm copper cable and provision of 2.5sqmm PVC insulated FRLS cable 1100 volts grade with multi stranded copper conductor for earth continuity conductor connected to common earth dolly connecting up to fittings complete.

Supply and fix Switch Piano, flush type, single pole, one way, 6 Amps, 240 volts, ISI marked complete all as specified and as directed. Make: Anchor / Legrand / Havells/crabtree/Leader

Supply and fix Switch Piano, flush type, single pole, two way, 6 Amps, 240 volts, ISI marked complete all as specified and as directed. Make: Anchor / Legrand / Havells/crabtree/Leader

Supply and fix Ceiling rose, surface type Bakelite, three terminal 65x32mm, ISI marked complete all as specified and as directed. Make: Anchor / Legrand / Havells/crabtree/Leader

Supply and fix Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed by Engineer-in-Charge. Make: Anchor / Legrand / Havells/crabtree/Leader

Supply and fix Modular switch 6 Amps 1 way 1module complete all as specified and as directed by Engr-in-Charge. Make : Anchor Roma/Legrand/Crabtree

Supply and fix Modular switch 16 Amps 1 way 1module complete all as specified and as directed by Engr-in-Charge. Make : Anchor Roma/Legrand/Crabtree

Supply and fix Electric call bell AC 230 V single pole ding dong type complete all as specified and as directed by Engr-in-Charge. Make : Anchor Roma/Legrand/Crabtree

Supply and fix Modular switch socket Outlet 6 Amps 2/3 pin 02 module complete all as specified and as directed by Engr-in-Charge. Make : Anchor Roma/Legrand/Crabtree

Supply and fix Modular switch socket Outlet Multi purpose 5/ 15 Amps 2/3 pin 02 module complete all as specified and as directed by Engr-in-Charge. Make : Anchor Roma/Legrand/Crabtree

Supply and fix Modular ceiling fan regulator,electronic step type 120w 2 module complete all as specified and as directed by Engr-in-Charge. Make : Anchor Roma/Legrand/Crabtree

Supply and fix Modular Bell push AC, 240 volt, 6 Amps, 01 Module complete all as specified and as directed by Engr-in-Charge. Make : Anchor Roma/Legrand/Crabtree

Supply and fix Modular metal flush box 1 way with modular white cover plate including frame complete all as specified and as directed by Engr-in-Charge. Make : Anchor Roma/Legrand/Crabtree

Supply and fix Modular metal flush box 2 way with modular white cover plate including frame complete all as specified and as directed by Engr-in-Charge. Make : Anchor Roma/Legrand/Crabtree

Supply and fix Modular metal flush box 3 way with modular white cover plate including frame complete all as specified and as directed by Engr-in-Charge. Make : Anchor Roma/Legrand/Crabtree

Supply and fix Modular metal flush box 4 way with modular white cover plate including frame complete all as specified and as directed by Engr-in-Charge. Make : Anchor Roma/Legrand/Crabtree

Supply and fix Modular metal flush box 6 way with modular white cover plate including frame complete all as specified and as directed by Engr-in-Charge. Make : Anchor Roma/Legrand/Crabtree

Supply and fix Modular metal flush box 8 way with modular white cover plate including frame complete all as specified and as directed by Engr-in-Charge. Make : Anchor Roma/Legrand/Crabtree

Supply and fix in repairs single pole and neutral enclosure with a three pin & earth plug with socket complete with one single pole MCB 20 Amps, 240Volts, 'C series, 50 Hz , breaking capacity 10 KA including metal flush box complete all as specified and as directed by Engr-in-Charge.

Supply and fix in repairs double door, sheet metal enclosure powder coated MCB DB SPN 8 way with 200 Amps rated bus bar, 240 volt,IP 42 protection, flush in walls including making good of disturbed surface to match with existing surface complete all as specified and as directed by Engineer-in-Charge. Make: Larsen & Toubro/ABB/Siemens/Schneider/Havells

Supply and fix in repairs double door, sheet metal enclosure powder coated MCCB DB TPN 8 way vertical type with neutral link earth bar din rail with 200 Amps rated bus bar, 415 volt,confirming to IS 13032-1991 including making good of disturbed surface to match with existing surface complete all as specified and as directed by Engineer-in-Charge. Make: Larsen & Toubro/ABB/Siemens/Schneider/Havells Note : for Main incomer of Main DB and MS pedestal panel incomer control

Supply and fix in repairs MCB TPN,63amps, 415 volts,25 KA complete all as specified and as directed by Engineer-in-Charge. Make: Larsen & Toubro/ABB/Siemens/Schneider/Havells

Supply and fix MCB SPN,6 to 32amps, 240 volts,10 KA complete all as specified and as directed by Engineer-in-Charge. Make: Larsen & Toubro/ABB/Siemens/Schneider/Havells

Supply and fix MCB SP 6 to 32amps, 240 volts,10 KA complete all as specified and as directed by Engineer-in-Charge. Make: Larsen & Toubro/ABB/Siemens/Schneider/Havells

Supply, install, test and commissioning batten type tube light LED 20w, trendy wall mounted, with extruded aluminium housing, with integrated LED driver, including necessary electrical wiring etc including taking down old unserviceable fittings complete all as specified and directed by Engr-in-Charge. Make :Havells Cat Part LUMILINEBS20WLED865SPCWH or equivalent in CG,Philips,HPL,Halonix,Surya

Supply and fix in repair LED tube light fitting, 1 X 10 Watts, 230 volts, with long lasting PVC body with slim and sleek looks all pre wired fixed on walls with all fixing accessories such as 2 Nos of PVC square/round box, screws etc and connecting up three core flexible copper conductor cable of size 24/0.20 sqmm, including 10w tube rod complete all as specified and as directed by Engineer-in-Charge. Make:-Philips/ Havells/CG/ Bajaj

Supply and fix table light fitting suitable for 9w LED bulb surface mounting adjustable type of up/down and 180 degree left/right movement with lamp shade fixed on wall with round or square block with LED bulb and including flexible connecting wire & accessories complete all as specified and as directed by Engineer-in-Charge. Make:-Philips/ Havells/CG/ Bajaj

Material and labour for Submain wiring complete with and including 2 runs of 6.0sqmm, single core FRLS, PVC insulated and unsheathed, multistranded, copper conductor cable, single core, 1100 Volts grade drawn through and including PVC conduit, medium grade of size 20mm including accessories such as Tees, Elbows, junction box, reducers etc as required and fixed on walls and 6.0 sqmm PVC multistranded copper conductor cable for earthing and connected to common earth dolly including taking down the existing submain wiring complete all as specified and as directed by Engineer-in-Charge. Make:Plaza/Finolex/Anchor/Havells/Nicco/Polycab/RPG Note :- (i) Two runs of 6.0 sqmm PVC insulated cable and one run of 6.0 sqmm cable for earth and one run of PVC conduit shall be measured as one unit length.

Material and labour for Submain wiring complete with and including 2 runs of 4.0sqmm, single core FRLS, PVC insulated and unsheathed, multistranded, copper conductor cable, single core, 1100 Volts grade drawn through and including PVC conduit, medium grade of size 25mm including accessories such as Tees, Elbows, junction box, reducers etc as required and fixed on walls and 4.0 sqmm PVC multistranded copper conductor cable for earthing and connected to common earth dolly including taking down the existing submain wiring complete all as specified and as directed by Engineer-in-Charge. Make:Plaza/Finolex/Anchor/Havells/Nicco/Polycab/RPG Note :- (i) Two runs of 4.0 sqmm PVC insulated cable and one run of 4.0 sqmm cable for earth and one run of PVC conduit shall be measured as one unit length.

Supply, install, test and commision LED street light fitting 1 x 45 watts,pressure die cast aluminium housing, Heat resistance toughened glass with frame, IP 66 protection, better optics for uniform distribution complete with necessary copper wire connection of suitable size complete all as specified and as directed by Engineer-in-Charge. Make - Bajaj Cat Part No BRTFG 45W LED or Equivalent in CG/ Philips/Havells/Halonix

Material and labour Earthing complete with Galvanised steel earth plate electrode 60 cm x 60 cm x 6.3 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of earth the plate not less than 1.5 metres below normal ground level, connected to and including galvanised earth lead wire 6 mm dia, 7.5 m long, by means of bolts, nuts, check nuts and washers made out of galvanised iron or steel with provision of charcoal & common salt packed upto minimum 150 mm all around the earth plate, and protected by 15 mm bore light grade galvanised iron pipe and connected to control board / panel / equipment complete all as shown in electrical plate No.3 of MES schedule Part I with PCC pit in PCC 1:2:4 type B1 using 20 mm graded stone aggregate, MS angle iron frame of size 50mm x 50mm x 5mm, cast iron cover with locking arrangements, GI 20 mm bore medium grade pipe and CI funnel with wire mesh for watering arrangement including necessary excavaion and earth work in any type of soil/strata & testing complete all as specified and as directed by Engineer-in-Charge.

Supplying, laying, testing and commissioning of UG round cable of following size, XLPE insulated, heavy duty, LT, 1100 V grade electric cable with aluminium conductor, served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed, as per IS-1554, laid in trenches or passing through pipe, making all connections with necessary glands, lugs, bushing etc as required including taking down old unserviceable cable complete all as specified and as directed by Engineer-in-Charge. Make: PARAGON/FINOLEX/PLAZA/POLYCAB/KALINGA/VINAY Note : Earthwork, excavation sand cushioning cable cover GI protection pipe shall be measured and paid separately in their respective items

95sqmm 3.5 core

70sqmm 3.5 core

50sqmm 3.5 core

Excavation in trenches not exceeding 1.5 m wide andnot exceeding 1.5 m in depth and getting out in Soft/loose soil for exposing of pipe etc complete all as specified and as directed by Engineer-in-charge.

Returning, filling in including spreading, leveling, watering and well ramming soil in layers not exceeding 25 cm thick complete all as specified and as directed by the Engineer-in-Charge

Removing excavated material to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and as directed by Engineer-in-Charge

Supplying and spreading in trenches fine dry river sand for cable cushioning and gently punning down in layers complete all as specified and as directed by Engineer-in-Charge Note : Thickness of sand cushioning shall be measured after punning and consolidating of sand.

Supplying and laying unreinforced precast concrete cable covers, class LV type, flat of size 250 mm x 150 mm x 40 mm complete all as specified and as directed by Engineer-in-Charge. Make : Mehtab Tiles ,Indore/M/S Ultra Tiles/NITCO/Topaz Tiles/Navya Tiles, Jodhpur

Supply and fix GI pipe, light grade, 80mm bore medium grade ISI marked for cable protection on wall, trenches, road crossings etc. with suitable size of GI saddle, wherever necessary complete all as specified and as directed by Engineer-in-Charge. Make: TATA/SWASTIK/JINDAL/Bharat Steel tube/ZENITH/Indian Tube Company

Supply and fix GI pipe, light grade, 50mm bore medium grade ISI marked for cable protection on wall, trenches, road crossings etc. with suitable size of GI saddle, wherever necessary complete all as specified and as directed by Engineer-in-Charge. Make: TATA/SWASTIK/JINDAL/Bharat Steel tube/ZENITH/Indian Tube Company

Material and labour for cutting the existing bituminous road to size not exc 45cm wide and depth not less than 45cm for passing of UG cable through GI pipe and making good the disturbed surface with C1 1:3:6 concrete using 20mm graded aggregate complete all as specified and directed by Engineer-in-Charge.

MAHENDRA REALTORS AND INFRSTRUCTURE PVT LTD