Jamalpur Water Supply Scheme under AMRUT 2.0

Financial Sheet

Name of work Jamalpur Water Supply Scheme under AMRUT 2.0

Address of Bidder

Part - A (SOR Items), BOQ attached with the Bid Document Amount (In Rs.)

1 Jamalpur Water Supply Scheme under AMRUT 2.0 842768241

Quoted rate in Percentage (In Figure)

Quoted rate in Percentage (In Words)

ABOVE / BELOW / ESTIMATED COST

Total Quoted Amount after Above/Below (Part A)

Part - B (Non- Schedule Items) Unit Qty Rate Quoted Amount (In Rs.)

1 Detailed Survey, Engineering Design and Preparation of Drawings for JamalpurWater Supply Scheme Job 1

E & M work of WTP & CWR

2 Supply, delivery at site & fixing in position, the Manual SS Sluice Gates, Design Basis: Velocity through Gate: 0.6-1.2m/sec,Size: 1m X 1 m ,Location: at the entry of by-pass channel & at the entry of flash mixer- to be placed in RCC channel, opening should be at the bottom of gate, hand wheel lift mounting should be to yoke, Specifications:MOC - Frame, yoke, slide, stem guide, stem extension - SS304L, Stem cover - clear polycarbonate, Side-seals - self adjusting UHMWPE, Bottom seal - resilient neoprene, Position indicator - Maylar slip, Stem configuration - Threaded rising stem, 303MX stainless steel,Manual operation - By hand wheel Manufacturer Nos. 2

Providing flash mixer electro- mechanical assembly with 2 HP capacity motor & required gear box (35-40 RPM), SS Shaft & impeller, mounting plate, teflon bush support, support bearing and coupling along with anti- corrosive painted MS sheet cover to motor & gearbox etc., complete, errection electrification & commissioning the unit.Supplying erection and commissioning of new reduction gear box (HELICAL GEAR BOX with suitable HP 4 RPM output model , flange vertical type gear oil filled) and Electrical AC motor 2HP, suitable for above gear box, 40mm dia , SS shaft and making coupling arrangements and fixing the same to gear box unit and providing SS flat of 6mm thick 100mm wide paddles and 2 mtrs or suitable height with required bolt, nuts & washers. Nos. 1

Supplying erection and commissionging and trial run for 3 months of required capacity (35 HP) Air Blowers system of Roots Type Capacity 0.5kg/Sqcm working pressure along with necessary motor, Air control valves, Air main GI piping including all necessary & suitable size piping arrangments from blowers to filter beds, necessary control/starter panels etc., Nos. 2

Supply, Erection, Fabrication and commissioning of steel bridge of Clarifacculator. MS clarifacculator bridge structural fabricated, 125x125x6mm/suitable channel, 50mmx50mmx6mm /suitable angles, Facculator peddles with shaft, centre bearing plate MS roller spring unit, gear box 3 Nos. motor suitable 2HP 2 Nos, bridge motor 3HP 1 no 3 MS chakkered plates of 5mm thick plates, rubber squezes, sprocket, spocket chain and one coat red oxide paint with electrical starter, wiring. Min 30 m Dia/Suitabeldia (SVISEW make) Bridge. Nos. 1

Supplying, fabrication and installation of Tube Settler modules of PVC / FRP material (60° inclined hexagonal tubes, height 1.0 m), conforming to CPHEEO Manual, including supporting structure of MS angles with epoxy painting, anchoring brackets, all hardware — installed in existing 30 m dia clarifier — all complete as per direction of E/I. Cum.M 700

Providing Alum agitator electro- mechanical assembly with 1.5 HP capacity motor & required gear box, SS Shaft & impeller, mounting plate, teflon bush support and coupling etc., complete, errection electrification & commissioning the units. Nos. 2

Providing Lime agitator electro- mechanical assembly with 1.5 HP capacity motor & required gear box, SS Shaft & impeller, mounting plate, teflon bush support and coupling etc., complete, errection electrification & commissioning the units and 5M to 6M Hot-Dip Galvanised Iron (GI) Octagonal/Tubular pole (thickness) with weather-proof overhead structural brackets, base flange plate, and high-tensile foundation J-bolts. Nos. 2

Dual Media Filter Bed (Per Filter Bed) Set 4

V-Wire Underdrain System : SETC of SS 316 Grade V-Wire/Wedge Wire screen laterals with precision slot openings of 0.2mm to 0.3mm to ensure zero media loss. Heavy-duty SS 316 Grade Central Manifold header collector pipe with a diameter sizing of 200mm to 250mm with structural standard end caps, companion flanges, gaskets, and SS 316 anchoring fasteners. Set 4

SETC of Solar Street Lighting System: Comprehensive Supply, Erection, Testing, and Commissioning of MNRE/BIS compliant 15W-18W LED Luminary (, IP66), Mono-PV Module, and Lithium Iron Phosphate battery package. Set 52

CWR with Pumphouse

Providing steel sheet pile on specified alignment and upto designed levels including painting the sheet piles with two coats of anti-corrosive bitumen paint (Portion of sheet pile inside concrete shell not be painted ) including cost of sheet piles as per specification and direction of E/I. Tonne 122.89

Pre-Settling Tank with Raw Water Reservior

Providing steel sheet pile on specified alignment and upto designed levels including painting the sheet piles with two coats of anti-corrosive bitumen paint (Portion of sheet pile inside concrete shell not be painted ) including cost of sheet piles as per specification and direction of E/I. Tonne 159.26

Repairing/Miscellaneous work in Existing WTP

Repairing of existing floating jetty

14 Repair and rehabilitation of existing floating jetty / bridge including dismantling of damaged wooden decking, replacement with new IS-marked hardwood / FRP decking planks, repair of MS pontoons by patching / welding of corroded plates (8 mm bottom & deck plate, 6 mm side plate), replacement of damaged web frames, anti-corrosive treatment, two coats of marine-grade anti-rust paint, replacement of mooring ropes, anchor chains, gangway hand rails — all complete as per direction of E/I. Job 1

Underwater inspection and de-silting of intake area around floating jetty by trained divers, including removal of accumulated silt, debris and aquatic growth from pump suction zone, depth verification, submission of inspection report — all complete as per direction of E/I. Job 1

Internal & external de-rusting (anti-rusting treatment) of existing Floating Jetty / Barge dimensions: 40 m × 7.50 m × 1.80 m, including mechanical brushing, chemical descaling, removal of corrosion products, sludge and incrustation by approved method — including all labour, scaffolding, lighting, ventilation inside pipe, safety equipment, debris disposal — all complete as per direction of E/I. Sqm 1542

Application of two coats of approved anti-corrosive / anti-rusting epoxy paint over de-rusted Floating Jetty / Barge dimensions: 40 m × 7.50 m × 1.80 m after surface preparation by SSPC-SP10 near-white blast cleaning standard — including primer coat, intermediate coat and finish coat, dry film thickness as per specification, all materials, labour, tools and tackle — all complete as per direction of E/I. Sqm 1542

Repairing of existing 600 mm dia MS Raw Water Rising Main

High-pressure flushing and cleaning of the existing 600 mm dia MS rising main using hydraulic jetting / scraper pigging / poly-pig including disposal of flushed water, supply of clean water for flushing, operation of intermediate valves, manpower and equipment — all complete as per direction of E/I. Per m 10600

Hydrostatic / stress testing of rehabilitated 600 mm dia MS rising main against minimum 120 m water head, including supply of water, pressurisation arrangement, gauges, blanking flanges, isolation, pressure holding for stipulated duration as per IS 5822 / AWWA C600, leak detection and rectification of any leak found, recording of test results — all complete as per direction of E/I. Per m 10600

Dismantling and removal of existing defective air valves Each 30

Dismantling and removal of existing defective Sluice valves Each 12

Repairing of existing RCC structures of WTP

Supplying, fabrication and installation of Tube Settler modules of PVC / FRP material (60° inclined hexagonal tubes, height 1.0 m), conforming to CPHEEO Manual, including supporting structure of MS angles with epoxy painting, anchoring brackets, all hardware — installed in existing 30 m dia clarifier — all complete as per direction of E/I. Sqm 700

Construction of new RCC weir at outlet of Tube Settler / Clarifier, including formwork, reinforcement (Fe-500 grade), M-25 concrete, V-notches at top, finishing with food-grade epoxy coating, modification of existing launder and outlet channel, hydraulic testing — all complete as per approved drawing and direction of E/I. Job 1

Total Quoted Amount (Part B)

Total Quoted Amount (Part A + Part B)