SPECIAL REPAIR TO OPERATING SURFACES NEAR BP NO 6 7 8 AT 1 WING AF STN SRINAGAR

Amount

Excavating over areas, n exc1.5 m deep and getting out in soft/loose soil,complete all as specified and directed.

Excavating over areas, exc1.5 m and n.exc 3.0 m deep and getting in soft/loose soil,complete all as specified and directed.

Removing Excavated soils to a distance not exc 50 m and depositing where directed at a level not exc1.5 m above the starting point, complete all as specified and directed.

Material and labour for Cement concrete flooring 25 mm thick type B-0 1:2:4 (using 12.5mm graded stone aggregate) for pading including water proofing compound to roof complete all as specified and directed. Note :- WPC shall be measured and paid separately under serial item No 06

Material and labour for 10mm thick plastering on fair faces of bricks or concrete surfaces finished even and fair without using extra cement and using WPC @ 3% by the weight of Cement in CM 1:4, complete all as specified and directed. NOTE :- WPC shall be measured and paid separately under ser item No 06.

Supply only Water proofing compound

Material and labour for wire brushing and cleaning top surface of tiles, lime terracing or cement concrete, including flashings and junction of parapets, etc., and surface painting, with a layer of blown grade bitumen of any penetration applied hot @ 1.7 kg per sq. m, blinded with grit or pea size gravel @ 0.006 cu.m per sq.m, and lightly tampered (area of flashings, etc., shall be added to the roof area) complete all as specified and directed.

Material and labour for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified and directed.

Forming embankments including raising (or lowering) earth, spreading in layers not exceeding 30 cm thick, watering, ramming/ rolling and finishing to required size, shape, etc., not exceeding 1.5 m high from base, complete all as specified and directed.

Forming embankments including raising (or lowering) earth, spreading in layers not exceeding 30 cm thick, watering, ramming/ rolling and finishing to required size, shape, etc., exceeding1.5m high from the base but not exceeding 3.0 m high from base, complete all as specified and directed.

Taking down cement plaster of any description including raking out joints, hacking for key, scrubbing down with water etc,complete all as specified and directed.

Material and labour for 15mm thick plastering on fair faces of bricks or concrete surfaces finished even and smooth without using extra cement in CM 1:6, complete all as specified and directed.

Material and labour for 15mm thick plastering on fair faces of bricks or concrete surfaces finished even and smooth without using extra cement in CM 1:4,complete all as specified and directed.

Preparation of newly plastered surfaces and applying two coat of exterior weather paint (Apex) over a coat of primer complete all as specified and directed.

Complete removal of existing treatment of old painted concrete/plaster or unplaster surfaces of walls including brooming down with steel wire brushing, scrapping down, smoke soot moulds, moss and efflorescent salts and greasy spots and applying two coat of exterior weather paint (Apex) complete all as specified and directed.

Preparation of newly plastered surfaces and applying three coats of White wash complete all as specified and directed.

Complete removal of existing treatment of old painted concrete/plaster or unplaster surfaces of walls including brooming down with steel wire brushing, scrapping down, smoke soot moulds, moss and efflorescent salts and greasy spots and applying Three coats of white wash complete all as specified and directed.

Supply and fixing Galvanised iron stay wire of size 7/4.00mm confirming to IS 2141:1979 of latest version having tensile strength 45-55 Kg/Sq mm and with minimum breaking load of individual strand 565 kg including fixing of brackets and tying arrangement in between blast wall and blast pens. complete all as specified and directed.

Demolition of cement concrete exc 15 cm thickness of any description and in any position not other wise specifically provided for and disposing off the demolished material by throwing out of runway premises complete all as specified and directed.

Material and labour for sand cushion layer below polythene film, complete complete all as specified and directed.

Material and labour for 400 Micron thick polythene film for separation layer under concrete complete all as specified and directed.

Material and labour for cement concrete work in pavement / hard standing of flexural strength 40kg/Sqcm in field using minimum 400Kg of cement per cum for thickness of concrete 25cm or less complete all as specified and directed. Note :- The cost of design mix shall be brone by the Contractor.

Material and Labour for Repair to broken spalled edges of joints, pot holes etc of existing concrete slab by cuting 'U' grooves with mechanical cutter, cleaning the joint portion thoroughly to ensure dust free joints using compresser air removing all dust/debris out of runway and applying compound of hardener and primer in the ratio of 1:2 by weight and filling the joints with epoxy mixture and quartz sand & silicon flour mix No 10 i n the ratio of 1:2:15 by weight and finishing the top surface smooth all as per manufacturers instructions , complete all as specified and directed of following sizes.Make: Fosroc Chemical//Bostic india Pvt. Ltd/ Choksey Chemicals Pvt Ltd or equivalent

Joints of size 1cm to 2cm wide and depth not exceeding 2.0 cm

Joints of size 1 cm to 2cm wide and depth exc 2.0 cm and not exceeding 4.0 cm

Material and Labour for forming dummy Joints 65 mm deep and 10 mm wide sealing compound from the joints cleaning with kerosene oil, drying with blow lamp, cleaning the joints portion throughly to ensure dust free joints using compressed air, trimming the edges of joints with diamond cutter and cleaning the joints atleast 40mm wherever required and removing all dust/ debris out of runway and filling the joints with polyurethene based sealent after applying a coat of primer to vertical surfaces of concrete which are in contact with the compound and finishing the joints properly leaving 3mm gap from top surface of concrete over and including backup rod complete all as specified and directed. Note: Any damage to the existing surface shall be made good by the contractor without any extra cost. Make: Colpar 200 PF of Fosroc Chemical//Bostic india Pvt. Ltd/ Choksey Chemicals Pvt Ltd or equivalent.

Material and labour for forming expansion joint 12 mm wide through the full thickness sealing compound from the joints cleaning with kerosene oil, drying with blow lamp, cleaning the joints portion throughly to ensure dust free joints using compressed air, trimming the edges of joints with diamond cutter and cleaning the joints atleast 40mm wherever required and removing all dust/ debris out of runway and filling the joints with polyurethene based sealent after applying a coat of primer to vertical surfaces of concrete which are in contact with the compound and finishing the joints properly leaving 3mm gap from top surface of concrete over and including surface complete all as specified and directed. Note: Any damage to the existing surface shall be made good by the contractor without any extra cost. Make: Colpar 200 PF of Fosroc Chemical//Bostic india Pvt. Ltd/ Choksey Chemicals Pvt Ltd or equivalent

Cutting and racking out old sealing compound from the old joints cleaning with kerosene oil, drying with blow lamp, cleaning the joints portion throughly to ensure dust free joints using compressed air, trimming the edges of joints with diamond cutter and cleaning the joints atleast 40mm wherever required, removing all dust/ debris out of runway and filling the existing joints with polyurethene based sealent after applying a coat of primer to vertical surfaces of concrete which are in contact with the compound and finishing the joints properly leaving 3mm gap from top surface of concrete over and including surface complete all as specified and directed.Note: Any damage to the existing surface shall be made good by the contractor without any extra cost. Make: Colpar 200 PF of Fosroc Chemical//Bostic india Pvt. Ltd/ Choksey Chemicals Pvt Ltd or equivalent

Joints of size 1cm to 1.5cm wide and 1.5 cm to 3.0 cm deep

Joints of size 2cm to 2.5cm wide and 1.5cm to 3.0 cm deep

Demolition of concrete n. exe 15 cm thickness of any description and in any position not other wise specifically provided for and disposing the demolished material thrown out of runway premises complete all as specified and directed.

Material and Labour for PCC 1:4:8 Type D2 (40mm) graded aggregate as in foundations, filling and mass concrete complete all as specified and as directed.

Form work in edges of concrete flats, break in floors, opening in concrete walls ,floors and roofs and sides of RCC/PCCbands in walls horizental or sloping and similar work all exceeding 20cm wide, complete all as specified and as directed.

Material and Labour for cement concrete type 1:2:4 B-2 using (40 mm graded aggregate) as in walls or retaining walls, any thickness,size,or shape including pillaster, buttresses columns, pillars boundry, pillars and post complete all as specified and as directed.

Plain Cement Concrete Type B1 1:2:4 (using 40 mm graded stone aggregate) in surface channels and drains complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc, complete all as specified and as directed.

M/S LATIF AHMAD MIR

M/S Abdul Ahad Rather

M/S RATHER CONSTRUCTION CO