Request for Proposal for FDI Jodhpur

Amount

EARTH WORK

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 500m and lift upto 1.5 m , disposed earth to be levelled and neatly dressed: All kinds of soil

Excavation for foundation up to 1.50 m to 3.00 m depth including sorting out and stacking of useful materials and disposing of the excavated stuff up to 500m lead.In All kinds of soil

Excavation for foundation up to 3.00 m to 5.00 m depth including sorting out and stacking of useful materials and disposing of the excavated stuff up to 500m lead.(for lifts, septic tank,water tank, Basement) In dense and hard soil

Filling available excavated earth in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead up to 50 meter and with all lift.

Supplying and filling earth including watering, ramming, consolidating and dressing complete. Including the rate of carrage (Fit for backfilling)

Supplying, Diluting and injection Chloropyrifos Emulsifiable concentrate 20% with 1% concentration for PRE-CONSTRUCTIONAL Anti termite treatment as per IS 6313 part III as amended from time to time and creating a continuous chemical barrier under and around the column pits, wall trenches, basement excavation, top surface of plinth filling, junction of wall and floor along the external perimeter of building expansion joints, over the top surface of consolidated earth of which aproch is to be laid surrounding of pipes and conduits etc. complete as per specification (Plinth floor area only shall be measured for payment and Including the cost of chemical emulsion)

PLAIN & REINFORCED CONCRETE( All the concrete works will have "FORM FINISH")

Basement & Below Ground

R.C.C Work for sub structure

Providing and laying in position Ready mix concrete manufactured in fully automatic Batching Plant and transported to site in transit mixer for having continous agitated mixer, manufactured as per approved mix design of specified grade of RCC work including pumping of R.M.C. from transit mixer to site of laying , including cost of admixtures in recommended portion as per IS 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer in charge , conforming to grade M35 (IS 456 – 2000) unless stated otherwise as per specifications in the following items at any depth or height, excluding the cost of steel reinforcement but including centering, shuttering, deshuttering, compacting with vibrators, curing and hacking the exposed surface wherever required to receive plaster or floated steel trowelled surface wherever specified. The rate shall include for providing recesses to slabs, walls and columns and sleeves and/or openings in slabs, construction joints, sunk slabs, cantilever slabs, making holes in formwork for taking out dowels etc. to the required shape, size and slope as shown in drawings.for the work of :-Footing,raft,columns,lift walls,retaining walls,pile caps,UG Underground domestic water tank, Fire tank, STP,WTP.CONCRETE TO HAVE MINIMUM CEMENT CONTENT OF 375 Kg./Cu.m. or as per design mix whichever is more

R.C.C Work

SUPER-STRUCTURE

Providing and laying in position Ready mix concrete manufactured in fully automatic Batching Plant and transported to site in transit mixer for having continous agitated mixer, manufactured as per approved mix design of specified grade of RCC work including pumping of R.M.C. from transit mixer to site of laying , including cost of admixtures in recommended portion as per IS 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer in charge , conforming to grade M35 (IS 456 – 2000) unless stated otherwise as per specifications in the following items at any depth or height, excluding the cost of steel reinforcement . The rate shall include for providing recesses to slabs, walls and columns and sleeves and/or openings in slabs, construction joints, sunk slabs, cantilever slabs, making holes in formwork for taking out dowels etc. to the required shape, size and slope as shown in drawings. The cost will include centring, shuttering, deshuttering, curing and compacting with vibrators. CONCRETE TO HAVE MINIMUM CEMENT CONTENT OF 375 Kg./Cu.m. for columns, slabs, beams and staircase, DG structure, overhead tank etc (the rate is inclusive of work upto all floor level including scaffolding & double scafloding ) or as per design mix whichever is more.

Supply & Fixing steel reinforcement for R.C.C. including transporting, decoiling, straightening, cutting, bending and placing in positing at all levels and binding with approved gauge binding wire. The rate to include for binding wire, chairs, spacers which will not be measured separately for payment. Quantity of steel as per drawing and with authorised overlaps only shall be measured and paid for. High yield strength deformed bars conforming to IS:1786 in all R.C.C. work (F.E. 500D Grade)

Plain Concrete

Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade including the cost of centering and shuttering - All work in M10 grade Nominal Mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) & minimum cement content to be 250 kg per Cu.mt

Supply & Fixing Structural Steel : Steel work welded, in built up sections framed work including cutting, hoisting, fixing with anchor bolts / fastners in position and applying priming coat of red oxide in columns, beams and joists, channels angles, tees flats with connecting plates or angle cleats. The rate shall include the cost of primer and two coats of enamel paint on all structural steel work.

Terrace Water Proofing Providing & Applying CIS Roofing (Cool Insulated Sustainable Roof): A complete water proofing on RCC substrate with two component acrylic water proofing coating (Hi seal slurry + Hi seal powder) with reinforced fabric Protected by 1:4 cement mortar plaster coat Followed by an Cementous insulation layer of Panache make or equivalent “Insulmix Screed”, which is encapsulated clay aggregate mixed with cement & polymers, which would provides insulation up to 0.087 K VALUE On top of that cement screed with M:20 design to provide proper slope as per design protected by COOL TOPS – 5 Coat Heat Reflective Coating System on Panache make or equivalent products (Cool Guard, Cool Top & Transeal)

Underground structure Water Proofing

Providing patented cement based waterproofing treatment from outside to Underground structure, liftpits, trenches and other underground strutures during construction consisting of waterproof layer over cement concrete 1:3:6 bedding finished with rough Kota stone of about 20mm thick well pointed in the joints with cement and approved water proofing compound as per manufacturer, specifications and continuing the treatment after completion of floor slab and side walls on the outer face of walls and upto a height of 300mm above the adjacent ground level the total thickness of water proofing treatment shall be about 75mm for floors and about 40mm for walls. The rate shall be inclusive of all material , labour equipment required and also cement slurry grouting if required (for vertical surfaces)

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of : i) Ist course of applying cement slurry @ 4.4 Kg/sum mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. ii) IInd course of 20mm cement plaster 1:3 (1 cement: 3 coarse sand) mixed with water. proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.. iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 Kg per Sq.mt. of area. iv) IVth course of 400 micron thick PVC sheet .(Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 Kg/Sq.mt.)

BRICK WORK/BLOCK WORK

Brick work with common burnt clay bricks of class designation 7.5 in superstructure above plinth level upto all floor in all shapes and sizes in : Cement mortar 1 : 4 (1 cement : 4 coarse sand) (the rate is inclusive of work upto all floor level including scaffolding & double scafloding )

Half brick masonry in Superstructure , above plinth level upto all level using bricks of designation 75 Cement mortar 1 : 4 (1 cement : 4 coarse sand) and providing and placing in position 2 Nos. ,6mm Ø M.S. bar at every third course of half brick masonry .(the rate is inclusive of work upto all floor level including scaffolding & double scafloding )

Providing and laying autoclaved aerated cement blocks masonry with AAC blocks of required size made using fly ash as basic raw material, blocks conforming to IS 2185 Part 3 (1989) having density in oven dry condition 551 - 650 Kg/Cum, minimum Compressive strength 3 N/mm2, thermal conductivity in air dry condition 0.24 W/mK, in super structure above plinth level in cement mortar 1:4 (1 cement : 4 coarse sand ) including providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work. Size of block - 200 x 200 x 600 (the rate is inclusive of work upto all floor level including scaffolding & double scafloding )

STONE MASONRY

Random Rubble stone masonry for with hard stone in foundation and plinth in Cement Sand mortar above 30 CM thick wall in Cement Mortar 1:4 ( 1-Cement : 4-Sand).

DOOR & WINDOW WORKS

SITC of powder coated Metallic Door (with OR without Vision Panel & with door frame) With door hinges and locking arrangements and both way handle. Prepare with rigid thermo fused film metal panels. Specification: 0.6mm thick Metal panel sheets, the internal cavity filled with adequate quantity of honeycomb. The material of the partition and that of the metal door will remain the same. The material of the partition and that of the metal door will remain the same. The door thickness shall be a minimum 45mm and the frame thickness shall be a minimum of 115mm.

SITC of 12mm thick Frameless tempered clear glass 12mm Glass Doors with fittings (Single / Double Doors) i. 12mm thick frame less clear tempered glass leaves, supported with appropriate patch fittings, Locks and 300-450mm SS handles. ii. Concealed floor closures shall have following features/properties: - iii. Suitable for any floor covering or threshold application. iv. Series employing a cam and roller mechanism. The closers shall be capable of controlling doors weighing up to 260 lb and measuring up to 3'-6". v. The closers shall have mechanical backcheck at approximately 70°. Dual valve adjustment to provide controlled closing speed from 175°–15° (sweep range) and 15°–0° (latch range). The closer mechanism [12:58, 3/5/2022] AEN Madam: shall provide adjustment within the cement case to allow 3/8" lateral, 1/4" longitudinal, and 5/32" vertical height adjustment. Versions shall be listed by UL and Series is certified to the requirements of ANSI/BHMA A156.4 for grade 1 closers. With door spring and locking arrangements and both way handle and patch fittings. Rates will include privecy film work as direction by engineer in charge

Providing and fixing at all levels & locations, 120 minutes fire rated steel Fire door and frame of Galvanized steel conforming to IS:277 of approved make, overall door assembly conforming to IS 3614 Part-1 & Part-2 & BS 476 Part 22 or EN 1634 as required . Fire doors should be tested at CBRI for rating of 120 minutes (supported by certificate). Frames should be provided with back plate bracket and anchor fasteners for installation on a finished plastered masonry wall opening. Frame should be grouted with cement & sand slurry necessary for fire doors on the clear masonry opening. Door shutter shall be made with minimum 1.2 mm thick steel pressed formed to provide a 46mm thick fully flush double skin door shell with lock seam joints at stiled edges. The internal construction or in fill material of the door to meet desired fire rating with reinforcement/rails at top, bottom, middle and vertical stile. The infill material shall be resin bonded honeycomb core or approved equivalent. The door shall be factory prepared for receiving appropriate hardware and provided with necessary reinforcement for hinges, locks, and door closers etc complete. The edges should be interlocked with a bending radius of 1.4mm. and shall have door astragals of required profile and size provided on the meeting stile for both active and inactive leaf. The shutter is to be fixed with frame with SS ball bearing butt hinges 3mm thick. Frame shall be fixed with approved dash fasteners and concrete should be poured in hollow frame section etc. Vision panel wherever applicable should be of size at least 300 x 300mm provided as per manufacturers recommendation with a beading and screws from inside with no screws and fasteners on the surface. The glass for vision panel should be 6mm clear fire rated glass of approved make & relevant rating of the door to withstand thermal shock upto 800 degree C on hose stream test. Door frames and shutters to be finished with power coating (minimum 50 micron), all complete as per the specifications and directions of Engineer-In-Charge. (Vision panel and handle rate is inclusive of the item and Hardware i.e. locks, door closer, Panic bar, etc shall be paid for separately)

Providing & fixing Fire rated door Closer of approved make certified for 2Hrs fire rating, all complete as per direction of Engineer in Charge.

Providing & fixing Fire rated Panic Exit Device (Panic Bar) of approved make certified for 2Hrs fire rating for fire door, all complete as per direction of Engineer in Charge.

Providing & fixing Fire rated Lock of approved make certified for 2Hrs fire rating, all complete as per direction of Engineer in Charge.

Providing and fixing external grade board solid core flush door shutters ISI 2202-67 marked using Phenol formal dehyderesin in glue both sides with approved steel fittings complete as per annexure 'A' including aldrop, mortice lock : 35 mm thick with decorative teak veneer with veneer polish both side. The rate shall include the work of pressed steel door frame confirming to IS 4351 manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges jamb, lock jamb, bead and if required angle threshold of mild steel angle of section. size as per directed by Engineer-in-charge

Extra for providing other type of fittings as mention in annexure A OF bsr 2019 ( as approved by EI) : Stainless Steel Fittings

Providing and fixing IS : 3564 marked Aluminium extruded section body tubular type universal hydraulic door closer with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing steel gate, grating, and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide. The rate shall include the cost of primer and enamel paint on all structural steel work.

Toilet Cubicles: Standard Cubicle Sizes (Regular) Total Height from Ground= 2003 mm Width = 910, 990 & 1060 mm Depth = 1550 mm Bottom Gap = 150 mm Door Size = 1750x610 mm Standard Cubicle Sizes (Differently abled) Total Height from Ground= 2003 mm Width = 1360,1660 & 1825 mm Depth = 1830 mm Bottom Gap = 150 mm Door Size = 1750x910 mm All doors, mid/end pilasters and Intermediate partitions to be made from 12 mm thick compact board of the same colour. Hardware and accessories to be in Nylon + Aluminium.Adjustable legs to anchored on the floor and then mid/end pilasters to be fixed on them. The adjustable legs are to be designed to give a bottom gap of 150 mm. On upper side top rail is fixed to maintain alignment of all pilasters. Intermediate panels (partitions) to fixed to mid pilaster and rear wall through U-channels. Each door is mounted on mid/end pilaster with 3 hinges maintaining a floor clearance of 150 mm. Door is also equipped with one coat hook and one door knob. Door can be either inside or outside opening. Opening of door can be left or right. Each Mid/end pilaster coming at the free end of the door is equipped with one privacy thumb-turn and one door stopper channel along with a rubber sponge to dampen the noise.

Design, Fabricate, deliver (Prefabricated & Assembled - to job site) and install uPVC casement windows from Saint-Gobain or equivalent. The outer frame and shutters should have a sill width of 70mm for two track and casement system as well as 128mm for three track sliding system. The face width of the sash should be minimum 110mm. uPVC profiles should have a minimum wall thickness of 2.3mm in the visible area. The profiles should be welded seamlessly Zip-welded without needing corner cleaning or grooved/raised finish. Both the shutter and bead profiles should have co-extruded gaskets in the glazing area. The frame and shutters should have EPDM gaskets in the sealing area. Steel reinforcement should be galvalum minimum of 1.5 mm thickness for frames and 2 mm for shutters and approved as per structural calculations. The glass panels shall be double glazed hermetically sealed panels made of 6mm thick Heat-strengthened coated glass - Envision series SKN 454 of Saint-Gobainor equivalent with coating on surface #2 with 12mm dry air gap and 6mm thick clear heat strengthened glass of Saint-Gobain or equivalent make(654 PPM) with properties as Visible Light Transmission (VLT) as 42%, Light Reflection internal as 22%, Light reflection External as 14%,Solar Factor as 0.24, and U value as 1.5 W/sqm.k and weighted average sound reduction as minimum of 30dB as per the detail drawings ,and securely bonded & Glass tolerance of ±0.2 as per EN Standard . Structural calculations to be submitted for both glass and frames. The vertical member should not deflect more than L/175 or 19mm for SGU and L/175 or 15mm for DGU, Deflection calculation should be based upon moment distribution. Steel reinforcement should have AluminoZinc coating for higher corrosion resistance. All hardware should be designed to withstand coastal conditions. 3D hinges to be used with adjustability in 3 directions. Multipoint locking to be provided with espags of SS304 grade. All shims to be capable of transferring the load evenly and made of a suitable material (Teflon, Nylon etc) capable of lasting the life span of the system. All miscellaneous items such as peripheral sealants, backer rods, fasteners etc to be included in the rate. (with mesh shutter & fixed aluminium grill)

STEEL, ALLUMINIUM AND IRON WORK

Supplying and fixing rolling shutters of approved make, made of 80 x 1.25mm. M.S. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including cost of spring hooks, providing and fixing necessary 25.3cm. long wire springs grade No. 2 and M.S. top cover 1.25mm thick for rolling shutters as per design & IS 6248- 1979. (Clear openable area to be measured for payment).

Providing & fixing ball bearing for rolling shutters

Extra for providing mechanical device chain and crank operation for operating rolling shutters. Exceeding 10.00 Sqm and upto 16.80 Sqm in the area.

Extra for providing mechanical device chain and crank operation for operating rolling shutters. Exceeding 16.80 Sqm in the area.

Extra for providing grilled rolling shutters manufactured out of 8 mm dia. M.S. bar instead of laths as per design approved by Engineer-in-charge. (area of grill to be measured).

Providing and fixing in position S.S. hand rail in main stair case, landing ,balconies etc. in 2"(50mm) dia S.S. pipe 1.5mm thk. 304 grade resting on1"( 25 mm) S.S. pipe 1.5mm thk. 304 grade size S.S.304 grade square bars 10mm, of clear height 105cms placed at 30 cm c/c including making necessary hold fast fixture (10 mm square bars 22 cm long) embeded in staircase concrete for resting the S.S 304 grade . vertical square bars with holding etc. as per approved design and as required for the work including bending hand rail pipe to proper shape in curves with specials etc. complete

PAVING AND FLOOR FINISHES

P & F 1st quality fully body Vitrified Porcelain Polished tiles with skirting of size 600 x 100mm height, 10 mm thickand on floor and steps etc.in different sizes (thickness to be specified by manufactuer) with water absortion less than 0.08% and conforming to IS 15622 of approved make in all colour and shade, laid with 20 mm thick CM 1 : 4 Tiles will be laid with 2 mm gap using spacers and gap will be filled with matching color epoxy latictere Size 600 x 600 mm.

P & F approved make & shade Full body Vitrified floor tile with granite pattern, laid with 20 mm thick CM 1 : 4 including grounting the joints with white cement and matching pigment etc complete. It should be antiskid smooth surface polished. Size 600 x 600 mm.

Providing and laying Antiskid Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigments etc., complete.

P & F approved make & shade Full body Vitrified Wall tile with granite pattern, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with white cement slurry @ 3.3kg per Sq.mt, including pointing in white cement mixed with pigment of matching shade complete. It Should be antiskit smooth surface polished. Size 600 x 600 mm.

Providing and fixing Ist quality ceramic glazed wall tiles 300*600 conforming to IS:15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing & laying sandwitch platform / water trough (sandwitch of 18 mm thk Granite of approved shade and sample on top and 25 mm thk kota in bottom with 30 mm thk screed of (1:2:4) in between)with sandwitch supports of 25 mm thk two kota on sides and screed in between and 75 mm raised platform with kota on top as per design and approved sample for all floors / all levels / all heights. The rate includes rounding, champhering and mirror polishing of edges, facias of granite, including necessary bonding adhesive like Araldite or equivalent. (Only plan area shall be measured and paid for). Rate shall be inclusive of making holes & cutouts for SS sink, Ovel wash basin, Piller tap, Bib tap-couplin etc. complete. Granite will be paid separately.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade.

Providing edge moulding to 18 mm thick granite stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/Granite/stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Kotah stone slab flooring with skirting of 100 mm height width factory cut, factory polished 25mm thick over 30 mm (average) thick base of cement mortar 1:6 (1 cement : 6 coarse sand) laid over & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing complete For area of each slab from 2001 to 5000 Sq.Cm

Providing and fixing Prepolished, machine cut 25 mm thick Kota in treads in single peice including 20 mm thick cement mortar 1 : 3, grouting the joints with white cement admixed with pigment, rounding of nosing, labour charges, cleaning etc complete as per details.

Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete

Providing and fixing Green / Black Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete and making grooves in stairs and filling it by aluminium strips and edge moulding of each steps.

Crazy ceramic tile flooring, with under layer 12 mm thick cement mortar 1:4 (1 cement: 4 coarse sand), with joints not exceeding 5 mm, including filling the gaps with ordinary cement mixture & mixing with synthetic polyester fibre, triangular in shape having specific gravity of 1.34 to 1.40, cross section size ranging from 10 to 40 micron & length upto 6 mm , mixing fibre @ 125 grams per 50 kg of cement in cement mortar, including providing and mixing water proofing material in mortar @ 1 kg per 50 kg of cement , all complete as per direction of Engineer-in-charge.

Providing, machine mixing and laying of 75mm thick vacuum dewatered (Tremix) concrete of grade M 20 of trap metal for plain cement concrete as per detail drawings including dewatering, steel form work, compaction, panels as specified and as per recommendation of manufacturer of equipment, power floating and broom finishing or finishing smooth as specified, cutting concrete for groove as expansion joint about 1/3rd depth of concrete and 6mm wide, filling grooves with approved bitumen based sealant, cleaning, curing surface etc. all complete

Rubble soling: Providing and laying in basement under floor rubble soling to a consolidated thickness of 200/300mm thick rubble stone and packing , using 200/250mm size stones, using murrum (gravel) hand packed with smaller stones of suitable size well rammed and consolidated including spreading in uniform layers watering ramming, consolidating all complete as per specifications.

a. With rubble from outside

PLASTERING AND PAINTING

Plaster on new surface on walls in cement sand mortar 1:4 including racking of joints etc. complete fine finish : 12 mm thk. Cost includes scaffolding and filling joints between concrete and masonry in cement mortar including racking the joints to form "V" groove (the rate is inclusive of work upto all floor level including scaffolding & double scafloding )

Plaster on new surface on walls in cement sand mortar 1:4 including racking of joint etc. complete fine finish : 20 mm thk Cost includes scaffolding and waterproofing compound and filling joints between concrete and masonry in cement mortar including racking the joints to form "V" groove (the rate is inclusive of work upto all floor level including scaffolding & double scafloding )

6 mm thick cement plaster to ceiling of mix 1:3 (1cement : 3-fine sand) Cost includes scaffolding(the rate is inclusive of work upto all floor level including scaffolding & double scaffloding )

Providing and fixing Chicken mesh jali (22 gauge) at the junction of 2 different surfaces of different material component at the time of plastering to prevent cracking in plaster surface as and where directed at all floors with all leads and lifts etc.complete.

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding: Two or more coats on new work including prepartion of base with primer, putty, lippy etc complete in all respect.

Providing and applying white cement based putty over plastered surface to prepare the surface even and smooth complete

COOL WALLS WITH COOL WRAP PREMIUM Providing & applying complete cool wall coatings(HI SRI Exterior paint) on wall surface with SRI Value of 107 Surface preparation: cleaning & washing Applying primer to give bonding to the substrate that reduces porosity & dampness of the surface 1 coat of primer & 2 coats of Panache make or equivalent product “COOL WRAP”.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work.

MISCELLANEOUS ITEMS

Providing and laying 750mm wide broom finished plinth protection with 230mm X 600mm (average) toe wall in brick masonry in C.M 1:6 over 75mm thick, 400mm wide PCC 1:5:10 (below masonry) broomed finished 750 mm wide and 100mm thick cement concrete 1:2:4 over 520mm wide 150mm thick PCC 1:5:10 ,with necessary grooves for expansion joints and curved vata at the junction of wall and plinth protection including excavation ,formwork,15mm thick cement plaster outside brick toe wall tec.complete as directed by Engineer -in-charge. Include rubble soling to a consolidated thickness of 200/300mm thick rubble stone and packing using murrum (gravel) hand packed with smaller stones of suitable size well rammed and consolidated including spreading in uniform layers watering ramming.

Grading roof for water proofing treatment with water proffing compound Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

100 MM or 50 MM WIDTH EXPANSION JOINT SETUP OF 50 MM EXPANSION SHEET:Cleaning of Concrete Surface on Both side of the Expansion Joints to remove any dust , Oil , Grease including Removal of laitence and cleaning the inside of the Expansion joint 2) Providing and applying base coat of Epoxy adhesive on both side of the joints as per width by SIKA -DUR 31C EPOXY and Placing the 3) Providing and Applying Combiplex Tape 300 mm * 1MM Expansion Joint Tape Tape 300 mm width x 1 mm thickness as per Manufacturers Methods Statement ( for 50 mm Lower Joint Side ) 4) Providing and applying the Top Coat of Epoxy Adhesives SIKA -DUR 31C EPOXY on both sides of the treated Expansion Joints as per the width of the EPDM SHEET 150MM* 1MM THICK . For terrace

Providing and fixing 150 mm wide sheet covering over expansion joints with iron screws as per design to match the colour / shade of wall treatment.Aluminum fluted strips 2 mm thick

Providing holes/pockets/cutouts in slab, beams, RCC walls with or without reinforcement during concreteing by providing forms, thermocoles including welding of reinforcement, shuttering, stagging, etc. as per drawing and direction.

(a) upto and including 0.25 Sqm but more than 0.04Sqm

(b) 0.25 SM to 0.50 SM

(c) 050 SM to 1 00 SM

Providing and fixing Metal perforated false ceiling at all heights including providing and fixing of frame work made of special sections power pressed from M.S. sheet and galvanised in accordance with zinc coating of grade 350 as per IS : 277 and consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling with dash fastener 12.5mm diax40mm long with 6mm dia bolts to the angle hangers of 25x25x0.55mm of required length, and other end of angle hanger being fixed with nut and bolts to G.I. channels 45x15x0.9mm running at the rate of 1200mm centre to centre to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre shall be fixed in a direction perpendicular to G.I. channel with connecting clips made out of 2.64mm diax230mm long G.I. wire at every junction including fixing of metal panels with ceiling section and perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre to centre with 25mm long drive-all screws @ 230mm interval and also including the cost of making openings for light fittings, grills, diffusers, cutouts and trap doors made with frame of perimeter channels suitably fixed all complete as per drawing and specification and direction of the Engineer in Charge (with trap door)

Providing & fixing calcium silicate ceiling tiles of size 595 x 595 mm in true horizontal level suspended on inter locking metal grid of hot dipped galvanised steel sections ( galvanized @ 170 gsm/sqm.) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38mm made from 0.30mm thick (minimum) sheet spaced at 1200mm center to center and cross “T” of size 24x25mm made of 0.30mm thick (minimum) sheet, 1200mm long spaced between main “T” at 600mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600mm and size 24x25mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 21x21x0.30 mm and laying false ceiling tiles of approved texture in the grid including, wherever, required, cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats fixed to ceiling with 6 mm dia and 50mm long dash fasteners, 4mm GI adjustable rods with galvanised level clips spaced at 1200mm center to center along main T, bottom exposed width of 24mm of all T-sections shall be pre-painted with polyester paint, all complete at all heights as per specifications drawings and as directed by Engineer-in-Charge of thickness of tiles as mentioned below. 8mm thick (with trap door)

Providing and fixing calcium silicate board false ceiling at all heights including providing and fixing of frame work made of special sections. 8mm thick (with trap door)

TANK WATERPROOFING TREATMENT:Providing & Applying a complete water proofing on RCC tanks. Identifying and sealing, filling of cracks if any with cement grout mixed with Panache make or equivalent, ‘Hi Seal Slurry’, repairs of pot holes if any, followed with priming of SBR. Laying of fiber mess and 2 Coats of two component Panache make or equivalent product mix of ‘Hi Seal Slurry Liquid & Powder’ resulting in to an onsite water proof membrane. Protected by 1:4 cement mortar plaster coat (Grey Cement +Panache make or equivalent product Hi CE Pack.Install protective screed by adding Panache make or equivalent admix Hi CE Pack up to 15 to 20 mm thick to bear the hydro pressure.Including material, labor, plant & tools etc.Rates are excluding the civil work of Protective screed of 15 to 20 mm .

WATER REPELLENT TREATMENT ON BRICKS AND EXPOSED:Providing & Applying of complete water repellent treatment by applying two coats of Panache make or equivalent NANOSEAL DRY LOOK (a silane siloxine water base water repellent) by brush or spray on concrete rendered surface / Exposed brick surface / stone cladding horizontal surface after proper cleaning and washing to that provides a complete water repellency to the surface without changing any aesthetic look of surface upto 5 years.(Including material, labour, plant & tools etc.)

Supply and installing Rain Water Percolation pits - 1500 mm in diameter up to 3200 mm deep, bottom 500 mm filled with boulders 150 - 230 mm size, over which one no. UPVC 160 mm dia (4.0 kg/cm2) perforated pipe with 8 mm dia perforations protected by a cowl on upper end 2100 mm long, surrounding filled with broken bricks up to 1000 mm, pebbles 40 to 50 mm up to 400 mm, Gravel 15 to 25 mm up to 400 mm and upper most layer of 300 mm with coarse sand of 3 to 5 mm. The top 600 mm shall be left open, with RCC grated cover on top.

Supply & Installation of toughened reflective glazing Glass :- (12 mm thick toughened glass) Including full glass of minimum 12 mm thick clear toughened glass, structural support system for top and bottom including holding system from RCC slab above false ceiling, including runner hung anchor fastener to fix it. Rubber interlinear & gaskets to fix bottom into SS "U" channel in floor. silicon sealant to filled gap.

Exposed face machine cut Stone work (machine cut edges) for Wall cladding/ Veneering work up to all floor with 20 to 30 mm thick Pink Sand stone (Bansi Paharpur) /White sand stone (Jpdhpur stone)and backing filled with a grout of 12mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing by means of clamps). The rate is inclusive of work up to all floor Level including scaffolding.

Providing and fixing stone jali 50 mm thick Jodhpur white sand stone as per ornamental design to be fixed with white cement/epoxy mortar including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade.

Design, fabrication, supply, testing, install complete, cleaning & handover of 20-25 mm thick GRC Panel cladding with joint filled with flexible sealant system, custom designed to withstand the design wind pressure confirming to IS -875 part III. (The system must pass the proof test at 1.5 times design wind pressure without any failure). For spray GRC, the maximum particle size shall be 1.2mm. i.e. sand passing a 150 micron sieve, shall be less than10% of the total weight of sand. With MS HDG/epoxy painted Stud frame (flex /gravity anchor/etc) having minimum 12 no of padding of 100x200x60 mm thick/as per requirement. GRC panel with Stud frame will be fixed on RCC, necessary base plate, fixing plate with nylon separate to be place between RCC and Base plate, fastener should be GI, Hilti/ Kilmas/ Fisher/ equivalent to be use. Nut and bolt will be HDG of required strength. Joint filling should be done by using non staining weather sealants to seal the gaps between two GFRC curved panels.

ACP Cladding:- Design, providing and fixing 4mm thick ACP Champaign Gold / Silver cladding manufactured with polythene core laminated in two sheets of 0.5mm approved coloured aluminum skins, with exterior coated in PVDF resin, cutting the edges if required and making notches on the edges, complete with silicon weather sealant DC 789, EPDM gasket, all SS 304 screws / bolts / fastener / clamps, flashing to ensure to resistance to water penetration and air permeability, with required chromotised aluminium grid work, complete at any level with all labour materials, transportation, lead & lift, necessary scaffolding, staging, taxes, levies, duties etc. and as per approved drawing specification and direction of Construction Manager / Engineer incharge .

SIGNAGES ON WALL: Providing, Fabricating & Fixing wall signage's using 304 grade Stainless steel brushed steel finish plate of 1.5 mm thick fixed on a wall using s.s studs including punched (laser cut) lettering carried out on s.s plate of required size and text as directed by Engineer over the S.S plate etc.complete. Size: 18" x 6"

SIGNAGES HANGING FROM CEILING Providing, Fabricating & Fixing signage's using 304 grade Stainless steel 1.5 mm thick brushed steel finish plate (2 nos) with 8mm thk. Acrylic sheet covered with vinyl of approved colour, sandwiched between two S.S plate and fixed with s.s struds . Sandwiched plates should be fixed in 12mm X 12mm S.S 1.5mm thk.304 grade frame and punched (laser cut) lettering carried out on both the s.s plates of required size and text as directed by Engineer and hanged to ceiling with the help of S.S 8mm thick chain at both ends with making all the fixing arrangement to the ceiling and to the plate complete etc.complete. size: 18" x 6"

Providing and fixing expanded grill made of aluminum as per design and drawing having members section of size 7.5mm x 6.0mm and opening of size 75mmx72mm to aluminum window/vent with required screws, Y and H aluminium sec (as per drawing) at the ends and middle joints respectively complete in all respect as per direction of engineer in charge. Powder coating aluminum ( minimum thickness of powder coating 50 micron)

Supply and installation of semi unitised structural glazing with PVDF Coated aluminim profiles designed for 1.5 kPa wind pressure. The rate is inclusive of required MS hot dip galvanised brackets, weather silicone DC789, structural silicone DC 983, SS304 screws, smoke seal, flashing,glass specification as mentioned, openable vents and spandral insulation as specified.The glass panels shall be double glazed hermetically sealed panels made of 6mm thick Heat-strengthened coated glass - Envision series SKN 454 of Saint-Gobainor equivalent with coating on surface #2 with 12mm dry air gap and 6mm thick clear heat strengthened glass of Saint-Gobain or equivalent make(654 PPM) with properties as Visible Light Transmission (VLT) as 42%, Light Reflection internal as 22%, Light reflection External as 14%,Solar Factor as 0.24, and U value as 1.5 W/sqm.k and weighted average sound reduction as minimum of 30dB as per the detail drawings ,and securely bonded & Glass tolerance of ±0.2 as per EN Standard . Vision Area- 24mm DGU (6+12 a/s+6) HS glass

Fine dressed stone flooring over 20 mm (average) thick base of cement mortar 1:4 ( 1cement : 4 coarse sand) with joints finished flush. Red Sand stone(Jodhpur stone) size not less than 1350 Cm2 - b) 50mm

Topography Survey using Dual frequency RTK base rover type arrangement DGPS,the job includes marking levels and coordinates with the help of total station.

Designing and constructing brick masonry inspection chamber of the following sizes in brick work of class 75 in cement mortar 1:5 (1 cement:5 fine sand), R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm. nominal size) embeded with frame for manhole, RCC foundation slab. 1:2:4 mix (1 cement : 2 coarse sand:4 graded stone aggregate 40 mm nominal size) both inside and outside of plastering 12 mm thick with cement motar 1:3 (1 cement : 3 coarse sand) with a floating coat of neat cement on inside face, proper water proofing to ensure no ground water seepage in the manhole, Poly propylene (conforming to ASTMD - 4101) foot rests (meeting the 224 kg load requirement as per IS 5455) at 300 mm spacing, benching and making channels with 1:2:4 cement concrete neatly finished, including necessary centering and shuttering, reinforcement, excavation, in all kind of soil, dewatering, refilling, watering, ramming and removing the surplus excavated earth, making good the same complete as required.

1. Contractor shall submit the structural design and drawings for the approval of Project Manager prior to execution.

450x 450 mm Size Depth Up to 450MM size

600 x 600 mm Size Depth Up to 900MM size

900 x 600 x Size Dpeth UP TO 900MM

1200 x 900 x 900 mm size

1400 x 900 mm (Arch type) (2500 mm deep)

1500 mm dia circular type (2300 mm deep)

Providing & fixing Ductile Iron Manhole cover with frame:

For 600 x 600 mm MH Medium Duty (B-125) Wt - 75 kg

450 x 450 mm, Medium Duty (B-125) Wt - 45 kg

For 900 x 600 mm MH

1200 x900 mm, Heavy Duty (C-250), Wt : 125 kg

1400 x 900 mm Heavy Duty (C-250), Wt : 125 kg

1500 mm Heavy Duty (C-250), Wt : 125 kg

Drilling or Core cutting, horizontal, vertical or inclined holes in reinforced cement concrete and / or hard rock

up to 75 mm diameter for a depth / length upto 300 mm

Diameters above 125 mm upto 200 mm for a depth / length upto 300 mm

Diameters above 200 mm upto 300 mm for a depth / length upto 300 mm

Providing & fixing in position as required PVC pipe 400MM long for sleeves in slab, beams, walls including making provision in formwork & finishing the same after deshuttering, to maintain the desired opening in perfect line & level for passage of services.

a. 25mm dia.

b. 40mm dia.

c. 50mm dia.

d. 65mm dia.

e. 75mm dia.

f. 100mmdia.

Boring with hydraulic piling rigs with power units, providing and installing cast in situ single under reamed piles of specified diameter and length below pile cap in M-25 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap) For 300 mm dia piles

Providing and fixing concertina coil fencing with required dia 610 mm (having 15 nos. round per 6 metre length) up to 3m height of wall with existing angle iron 'Y' shaped placed 2.4 m apart and with 9 horizontal R.B.T. stud tied with GI staples and GI clips to retain horizontal including necessary bolts or GI barbed wire tied to angle iron all complete as per direction of Engineer In Charge with reinforced barbed tape (R.B.T.)/Spring core(2.5 mm thick) wire of high tensile strength of 165 kg/sq.mm with tape (0.52 mm thick) and weight 43.478 gm/metre (Cost of MS angle, CC block shall be paid extra) RBT Reinforced Barbed Tape BTOBarbed Tape Obstacle 30 having Blade length ,Blade width ,Blade space ,Core wire dia All as per given specification of RFP

Description of Work / Item(s)

Amount

SITC of BMS Computer System: i7 Processor or Equivalet Server PC, Intel(R) Xeon(R) Processor, 2.93GHz, 4MB Cache with 16 GB RAM, & 1 TB HDD, 10/100 Mbps Ethernet card, USB connection & internal modem, Microsoft(R) Windows(R) 7 OS Professional Enterprise, Web server software, DVD-ROM Drive (with RAM), 100/1000 Mbps NIC for Network connection and anti virus software with 32" colour graphics monitor as per Tender Specifications. Accessories included Optical Mouse, Key Pad, Laserjet colour A4 printer with the above BMS System configuration. Windows Licensed software compatible with the BMS platform etc. complete as required.

Application Software

SITC of the following window based graphical software for IBMS system with 2 Nos Client for Operator workstation. License for minimum 10000 hard/soft I/Os to be considered and shall have provision of future expansion . The following software packages shall have below minimum features and compliances.

a) 3D & HD vector dynamic graphics with Autocad import of plan with Zoom In & Zoom Out facility b) Native 64 Bit System , BTL,UL,EN Certified System, BACnet Profile B-AWS (Advanced workstation) as per the BTL Listing c) Multi-Monitor Support-( Min 4 Nos), Multi-language support,Object tracking on multiple cameras d) Certified OPC DA Server by OPC Foundation e) HTML5 based Web-Server software shall permit use of Standard Web-Browsers such as Microsoft Edge, Google Chrome, Mozilla Firefox, etc f) The Software shall comply to international standards and strive to deliver products that meet security standards such as ISA/IEC 62443, UL2900, ISO/IEC 27001, ISO/IEC62443 and OWASP g) Cybersecurity SL2, Seamless integration of Security certificates within customer IT infrastructure, Microsoft’s active directory-based authentication, LDAP integration, Use of network infrastructure that supports physical network or VLAN segmentation, End-to-end encryption from client to server, End-to-end encryption between servers, Certificate-based data exchange, Encrypted backups h) Audit Trail , 4-Eye Principle, Data Point Validation, Verified tempering evidence for report transmission i) The software shall integrate with BIM data seamlessly j) Ability to provide data to other systems thru OPC DA Server and / Or Rest web services interface k) Reports - Customized reports for Trends and alarm with Graphic screen shots. l) Seamless integration of Fire alarm system should be there. m) Alarm Escalation: Assisted treatment of alarms which helps in Predefined & fast intervention steps for faster response n) Energy dashboards having cockpit view of total energy utilized. Energy and Power reports.

SITC of True IP Based DDC Standalone 32 Bit Intelligent, peer to peer communication, interoperable DDC as per the specification. The compact controller shall have inbuilt 2-port Ethernet switch . The controller shall have 16 inputs/outputs inbuilt and can be expandable upto max 40 points by Input/Output Modules. The DDC shall have 300 Mhz processor with 128 MByte SDRAM (DDR3) and 512 MByte NAND Flash. DDC Controller shall be equipped with a battery-free real-time clock with backup for min 7 days using super capacitor. The controller shall be freely programmable and have System functions (alarming, scheduling, trending, access protection with individually definable user profiles and categories). It should have WLAN interface, Cloud connectivity for remote access and inbuilt port for POT for local interface. Note: Comissioning tool should not be dependent on any license / dongle and no extra cost should be charged. (Make:- Johnson Control-Metasys/ Siemens/ ALC)

The above shall be housed in vandal proof, lockable & secure MS Cabinets to be supplied along with all necessary switchgear protections as required. Number of controllers shall have spare capacity of 15% for future expansion.

Controller for Chiller plant and Pumps system

Controller for Hot Water Generator System

Controller for AHU system

Controller for TFA system

Controller for Exhaust Fan & Air Washer ( 4 Fans in 1 DDC)

Controller for DG Sets

Controller for Fire Fighting system

Controller for Water treatment plant pump and Plumbing System Pump

Controller for FCU system (4 FCU in 1 DDC)

Controller for CS-AHU system (2 CS-ACU in 1 DDC)

Controller for Electrical system -HT LT Panel

Controller for Transformer

Controller for Dehumidifier ( 2 Dehumidifier in 1 DDC)

Controller for dry scrubber ( 2 Dry scrubber in 1 DDC)

Controller for Ventilation Fans ( 4 Fans in 1 DDC)

Controller for Pressurization Fans ( 6 Fans in 1 DDC)

SITC of True IP Based BTL & UL Listed for third party integration. The controller shall have 2-port Ethernet switch and WLAN interface. It should have BTL label (BACnet communications passed the BTL test) and consisting of Dual microprocessor with Storage capacity of 1 GByte RAM. It should support Real Time clock with backup of upto 7 Days using super capacitor and also should have option for external battery if required. It should Support of the major communication protocols: BACnet,/IP, BACnet MS/TP, Modbus IP and Modbus RTU upto 500 points. Note: 3rd party make integartor is not acceptable. (For Following Items)

For Chillers on Bacnet/IP or Modbus/RS 485 (25 Points per Chiller)

For Secondary Pumps VFD on Modbus RS485 (10 Poins per VFD)

For AHU VFDs on Modbus RS485 (10 Points per VFD)

For DG Sets on Modbus RS485 (18 Points per DG)

For UPS on Modbus/RS485 (10 Points per UPS)

For Lifts on Modbus over RS485 (5 Points per Lift)

For Fire Alarm System on Bacnet/IP or Modbus/RS 485

For CCTV integration

For Access control integation

For VRF integration on Bacnet/IP or Modbus/RS 485

For Energy Meter integration

For Flow Meter integration

Field instruments

Supplying, installing, testing and commissioning of the following sensors / transducers / transmitters. The DDC shall support sensor with DC 0...20 mA or 4...20 mA, DC 0 ... 10 V, LG-Ni 1000, 2x LG-Ni1000, Pt 1000 , NTC 10k, NTC 100k, 1000 Ohm. All sensors should be UL Listed.

Immersion temperature sensor 100 mm Pt1000 with Brass Thermowell.

Outside air temperature + humidity sensors for measuring outside air temperature. It should be provided with sun sheild and rain protection.

Water Flow Switch

Differential Water pressure sensor

Differential Pressure Switch Water

Absolute water Pressure Sensor

Differential pressure switch for Blower and Filter Status

Bi Level Switch

Duct type temperature Sensor

Differential Pressure Sensor Air

Space type CO2 sensor

Flameproof Level Switch

Current Relay

Supply, installation, testing and commissioning of hand held portable operator terminals (POT) minimum 15 inch. TFT display with capacitive touch screen type, shall be able to view graphs , alarms , parameters etc. POT shall have integrated web server and a BACnet/ IP web interface to connect a HTML5 browser to a device on the network. POT With all required connectors etc as per technical specification etc.

Cabling and Conduiting

Supplying, laying, termination, testing and commissioning of armoured signal cables. (4 core x 1.0 Sq.mm), PVC insulated, unshielded tinned copper conductor cable.

Supplying, laying, termination, testing and commissioning of armoured Communication cables. (2 core x 1.0 Sq.mm), PVC insulated, shielded twisted copper conductor cable.

Supplying, laying, termination, testing and commissioning of 3 Core 1.5 Sqmm, unarmoured ATC conductor multistranded, FRLS cable for Powering DDC , Actuators

Supplying, laying, termination, testing & commissioning of CAT 6 unarmoured Cables with required accessories like RJ45 connector etc.

Supply, Installation, Testing & Commissioning of PVC Conduit 25 mm for Signal & Communication Cable

Supply, Installation, Testing & Commissioning of GI Flexible

Network Switches

Supply, installation, testing and commissioning of Layer 2 switch with 16 ports (RJ-45) including SFP modules, rack mountable, SMPS power supply & other termination accessories (Like Pigtails/LIUs/ Convertors/Splicing equipment ,Patch panel, Patch Cord, Etc) complete as per specifications and as required for BMS DDC Panel Networking. The switch to switch distance shall not exceed beyond 80 meters.

Description of Work / Item(s)

Amount

HYDROPNEUMATIC SYSTEM AND VARIOUS PUMPS

Variable Speed Hydro-booster System for domestic water supply :

Compact self contained Hydro-booster system comprising of following : a. In-line, vertial multistage, centrifugal clear water pumps with SS-304 casing, S.S 304 impeller and SS-304 shaft, C.I. Base CED coating & head TEFC motor (with mechanical seal) Vendor to submit performance curves and technical catalogue of the proposed model for review and information. b. Panel mounted microprocessor multi pump contoller with large graphical display with VGA 240 x 320 pixels and variable frequency drive (VFD) integrated in a single body or as separate components with pressure sensor transmitter (one dedicated to each pump), diodes to indicate pump ready, pump running and fault and capable to communicate with other controllers following MODBUS-RTU or BACNET Class-2 protocol through RS485 port. System should be capable to compensate for frictional losses at lower flows. All alarms should be displayed in the controller. System should be equipped with dry running protection. Indication of all type of faults / on-off status / electrical parameters shall be available on panel and central IBMS monitors. On-off operation for all pumps shall be availble on BMS system c. Pre-charged diaphragm pressure vessel with interchangeable membrane, charging connection, connected to outlet header with necessary flanges, gaskets, isolating valves, nuts/bolts etc. complete. d. Set of accessories such as G.I headers for suction and discharge, control valves, non return valves, pressure switches, pressure transducers, pressure gauge, flow meters, inter connecting power and control cabling etc. complete.

For supplying DWS to DEAN DIRETCOR Residance - (Hydro-1)

Capacity per pump - 3000.0 m3/hour] Head - 45 mt Approx. Elec. Load. - Location - PUMP ROOM Pressure vessel - as per manufacturer recommendation). 1 Set = 2Nos. Pump (1 Working + 1 Standby - cascade operation) Suction head - flooded positive suction Supply Installation, testing & commissioning

For supplying DWS to Hostel Block - (Hydro-2)

Capacity per pump - 20000.0 m3/hour] Head - 70 mt Approx. Elec. Load. - Location - PUMP ROOM Pressure vessel - as per manufacturer recommendation). 1 Set = 3 Nos. Pump (2 Working + 1 Standby - cascade operation) Suction head - flooded positive suction Supply Installation, testing & commissioning

For supplying DWS to GUEST HOUSEl Block - (Hydro-3)

Capacity per pump - 6000.0 m3/hour] Head - 45 mt Approx. Elec. Load. - Location - PUMP ROOM Pressure vessel - as per manufacturer recommendation). 1 Set =2Nos. Pump (1 Working + 1 Standby - cascade operation) Suction head - flooded positive suction Supply Installation, testing & commissioning

For supplying DWS to NON TEACHING Block - (Hydro-4)

Capacity per pump - 6000.0 m3/hour] Head - 60 mt Approx. Elec. Load. - Location - PUMP ROOM Pressure vessel - as per manufacturer recommendation). 1 Set = 2 Nos. Pump (1 Working + 1 Standby - cascade operation) Suction head - flooded positive suction Supply Installation, testing & commissioning

For supplying DWS to Faculty Block - (Hydro-5)

Capacity per pump - 15.0 m3/hour] Head - 60 mt Approx. Elec. Load. - Location - PUMP ROOM Pressure vessel - as per manufacturer recommendation). 1 Set = 2 Nos. Pump (1 Working + 1 Standby - cascade operation) Suction head - flooded positive suction Supply Installation, testing & commissioning

For supplying Gate House - (Hydro-6)

Capacity per pump - 1.0 m3/hour] Head - 30 mt Approx. Elec. Load. - Location - PUMP ROOM Pressure vessel - as per manufacturer recommendation). 1 Set = 2 Nos. Pump (1 Working + 1 Standby - cascade operation) Suction head - flooded positive suction Supply Installation, testing & commissioning Pump type horizontal

Water Supply / Transfer Pumps :

In-line, vertial multistage, centrifugal clear water pumps, speed upto 2900 rpm, with SS-304 casing, S.S 304 impeller and SS-304 shaft, C.I. Base CED coating & head, connected to a TEFC motor (with mechanical seal) suitable for 400 / 440 volts, 3 phase 50 cycles A.C. supply with 150 mm dia pressure guage with gunmetal isolation valve, vibration eliminating pads as required, M.S fabricated base plate bolted to cement concrete foundations complete. Vendor to submit performance curves and technical catalogue of the proposed model for review and information.

Electrical Starter panels complete with O/L Relay with Single phasing preventer feature, earth leakage relay, ON-OFF and Trip Indicating lamps, contactors contacts for Building Automation System, interlocking, level controller with operational mode as one pump working at low level, both pumps at high level with a hooter alarm and cut off at dry level, cascade operation, working / standby slelction, etc. suitable for the motor H.P. as specified below and with provision for remote P.B. on/off complete as required. The on/off operations for all pumps shall be available on central BMS system

WATER TREATMENT FEED PUMP /TRANSFER PUMP - P1

For transfer water raw water tank to domestic underground water tank

Capacity per pump - 30.0 m3/hour] Head - 30.0 mt 1 Set = 3 Nos. pump (2 working+1 standby), cascade operation Approx. Elec. Load. - Location - Pump Room Supply Installation, testing & commissioning with Set of Auto Level Sensor FOR ACADEMIC BLOCK TOWER-1

For Transfer domestic underground water tank to OH wtaer tank FOR ACADEMIC BLOCK TOWER-2

Capacity per pump - 15.0 m3/hour] Head - 85.0 mt 1 Set = 1 Nos. pump (1 working+1 standby), cascade operation Approx. Elec. Load. - Location - Pump Room Supply Installation, testing & commissioning with Set of Auto Level Sensor

For Transfer domes tic underground water tank to OH wtaer tank FOR ACADEMIC BLOCK TOWER-1

Capacity per pump - 15.0 m3/hour] Head - 110.0 mt 1 Set = 1 Nos. pump (1 working+1 standby), cascade operation Approx. Elec. Load. - Location - Pump Room Supply Installation, testing & commissioning with Set of Auto Level Sensor

FWS Transfer Pump - P2

For transferring water from STP pump room to flushing water over head tank

Supply, installation, testing & commissioning of Submersible single stage single entry pumps connected to submersible motor (The motor shall be watertight according to IEC class IP 68, and incorporate class F, insulation materials to withstand a continuous operating temperature of 155 deg C) for 415 + 10% volts, 3 phase, 50 cycles A.C. power supply with mechanical seal, pump connector unit with rubber diaphragm and bend, vertical discharge pipe, electrical panel with in built level controller with operational mode as one pump working at low level, both pumps at high level with a hooter alarm and cut off at dry level as determined. The pump shall be provided with a lifting devise of pull chain/guide rail & G.I. heavy class rising main of 5m length including interconnecting piping, valves (Ball Valve / Butterfly), Non return valves (GM/CI) 15 m cable etc. as per requirement complete in all respects. (Pumps shall be installed in a set of two pumps One working and One standby, with cascade operation).

(Pumps suitable to handle solids upto 25 mm size with C.I. body, SS304 shaft, C.I. impeller with 15 mtrs cable, double mechanical seal).

Electrical Starter panels complete with O/L Relay with Single phasing preventer feature, earth leakage relay, ON-OFF and Trip Indicating lamps, contactors contacts for Building Automation System, interlocking, level controller with operational mode as one pump working at low level, both pumps at high level with a hooter alarm and cut off at dry level, cascade operation, working / standby slelction, etc. suitable for the motor H.P. as specified below and with provision for remote P.B. on/off complete as required. The on/off operations for all pumps shall be available on central BMS system

Dean Residenace

Capacity per pump - 2 m3/hour Head - 30.0 mt 1 Set = 2 Nos. pump (1 working+1 standby), cascade operation Approx. Elec. Load. - Location - STP Area Supply Installation, testing & commissioning with Set Og Auto Level Sensor

Hostel Block

Capacity per pump - 10 m3/hour Head - 45.0 mt 1 Set = 2 Nos. pump (1 working+1 standby), cascade operation Approx. Elec. Load. - Location - STP Area Supply Installation, testing & commissioning with Set Og Auto Level Sensor

Guest House Block

Capacity per pump - 4 m3/hour Head - 30.0 mt 1 Set = 2 Nos. pump (1 working+1 standby), cascade operation Approx. Elec. Load. - Location - STP Area Supply Installation, testing & commissioning with Set Og Auto Level Sensor

NON TEACHING

Capacity per pump - 4 m3/hour Head - 40.0 mt 1 Set = 2 Nos. pump (1 working+1 standby), cascade operation Approx. Elec. Load. - Location - STP Area Supply Installation, testing & commissioning with Set Og Auto Level Sensor

ACADEMIC TOWER-1

Capacity per pump - 10 m3/hour Head - 85.0 mt 1 Set = 2 Nos. pump (1 working+1 standby), cascade operation Approx. Elec. Load. - Location - STP Area Supply Installation, testing & commissioning with Set Og Auto Level Sensor

ACADEMIC TOWER-1

Capacity per pump - 10 m3/hour Head - 110.0 mt 1 Set = 2 Nos. pump (1 working+1 standby), cascade operation Approx. Elec. Load. - Location - STP Area Supply Installation, testing & commissioning with Set Og Auto Level Sensor

FACULTY BLOCK

Capacity per pump - 10 m3/hour Head - 45.0 mt 1 Set = 2 Nos. pump (1 working+1 standby), cascade operation Approx. Elec. Load. - Location - STP Area Supply Installation, testing & commissioning with Set Og Auto Level Sensor

Hot Water Circulating Pump - P4

Electrical starter panel shall include the thermostat, required sensors and the timer control panel with all other requirements as specified above as well as in technical specifications. (Guest Room)

Capacity/Flow Rate - 2.5 LPS (9.0 M3/Hr) Head - 20.00 mt 1 Set = 2 Nos. pump (1 working+1 standby), cascade operation Approx. Elec. Load. - 0.5 KW Location - Terrace Supply Installation, testing & commissioning

Basement Drainage Pumps / Mud Pumps:

Supply, installation, testing & commissioning of Submersible single stage single entry pumps connected to submersible motor (The motor shall be watertight according to IEC class IP 68, and incorporate class F, insulation materials to withstand a continuous operating temperature of 155 deg C) for 415 + 10% volts, 3 phase, 50 cycles A.C. power supply with mechanical seal, pump connector unit with rubber diaphragm and bend, vertical discharge pipe, electrical panel with in built level controller with operational mode as one pump working at low level, both pumps at high level with a hooter alarm and cut off at dry level as determined. The pump shall be provided with a lifting devise of pull chain/guide rail & G.I. heavy class rising main of 5m length including interconnecting piping, valves (Ball Valve / Butterfly), Non return valves (GM/CI) 15 m cable etc. as per requirement complete in all respects. (Pumps shall be installed in a set of two pumps One working and One standby, with cascade operation).

(Pumps suitable to handle solids upto 25 mm size with C.I. body, SS304 shaft, C.I. impeller with 15 mtrs cable, double mechanical seal).

Electrical Starter panels complete with O/L Relay with Single phasing preventer feature, earth leakage relay, ON-OFF and Trip Indicating lamps, contactors contacts for Building Automation System, interlocking, level controller with operational mode as one pump working at low level, both pumps at high level with a hooter alarm and cut off at dry level, cascade operation, working / standby slelction, etc. suitable for the motor H.P. as specified below and with provision for remote P.B. on/off complete as required. The on/off operations for all pumps shall be available on central BMS system

Mud pump for Ramp Sump drainage - MP1 - 3000 liter capacity

Capacity/Flow Rate - 2.78 LPS (10.0 M3/Hr) Head - 15.0 mt 1 Set = 2 Nos. pump (1 working+ 1 standby), cascade operation Approx. Elec. Load. - 1.5 KW each pump RPM - 2900 MOC - C.I Casing / C.I. Impeller / S.S. Shaft Location - Ramp 35 MM Solid handling Supply Installation, testing & commissioning

Sewage Pumps with grinder:

Supply, installation, testing & commissioning of Submersible single stage single entry pumps connected to submersible motor (The motor shall be watertight according to IEC class IP 68, and incorporate class F, insulation materials to withstand a continuous operating temperature of 155 deg C) for 415 + 10% volts, 3 phase, 50 cycles A.C. power supply with mechanical seal, pump connector unit with rubber diaphragm and bend, vertical discharge pipe, electrical panel with in built level controller with operational mode as one pump working at low level, both pumps at high level with a hooter alarm and cut off at dry level as determined. The pump shall be provided with a lifting devise of pull chain/guide rail & G.I. heavy class rising main of 5m length including interconnecting piping, valves (Ball Valve / Butterfly), Non return valves (GM/CI) 15 m cable etc. as per requirement complete in all respects. (Pumps shall be installed in a set of two pumps One working and One standby, with cascade operation).

(Pumps with grinder system suitable to handle solids upto 25 mm size with C.I. body, SS304 shaft, C.I. impeller with 15 mtrs cable, double mechanical seal).

Electrical Starter panels complete with O/L Relay with Single phasing preventer feature, earth leakage relay, ON-OFF and Trip Indicating lamps, contactors contacts for Building Automation System, interlocking, level controller with operational mode as one pump working at low level, both pumps at high level with a hooter alarm and cut off at dry level, cascade operation, working / standby slelction, etc. suitable for the motor H.P. as specified below and with provision for remote P.B. on/off complete as required. The on/off operations for all pumps shall be available on central BMS system

Grinder pump for STP Area Sump drainage - SP1 - 1700 liter capacity

Capacity/Flow Rate - 2.78 LPS (10.0 M3/Hr) Head - 15.0 mt 1 Set = 2 Nos. pump (1 working+ 1 standby), cascade operation Approx. Elec. Load. - 1.5 KW each pump RPM - 2900 MOC - C.I Casing/C.I. Impeller/S.S. Shaft Location - Basement -1 STP Supply Installation, testing & commissioning

WATER TREATMENT EQUIPMENTS :

Providing, fixing, testing & commissioning of skid mounted fully automatic Reverse Osmosis System of output capacity 2000 lt./hr. designed at a minimum Flux at inlet and necessary of minimum 60-70% recovery, complete as required with the following items: (1 working ) - R.O plant at Terrace Level for Drinking purpose Garnet Filter (GF) Media for GF - 1 LOT Antiscalant Dosing System with level sensors Cartridge Filter High pressure pump R.O. Feed pump R.O. Block Membranes Pressure Tubes RO skid pH correction system Necessary instruments Interconnecting pipe with necessary valve work i) PVC (upto HP Pump) ii) SS (HP Pump to Membrane) Pressure gauges Flow meter with Totalliser PPLC cum instrument panel Conductivity Indicator Level sensors (Antiscalent Tank) - H/L Level sensors (Permeate Tank) - H/L Control Valve (Inlet) to R.O. tank Control Valve (Reject) RO electrical control panel. R.O Plant SET as per above specification

R.O Plant with S.S.316 L ,13 mm thick EPDM Rubber insulated Storage tank of 2000 ltrs capacity installed at terrace level

R.O Plant with S.S.316 L ,13 mm thick EPDM Rubber insulated Storage tank of 2000 ltrs capacity installed at terrace level

Online U.V. treatment with single wave-length UV for disinfection of 3.0 cum/hr average flow; UV dosage of 300 to 400 joules/sqm, with more than 90% UVT for domestic water supply

SITC of Motorise valve - (Automatic OHT Level Control System - Butterfly Valve - IP55CB-230VAC 1) On-Off Type Electrical Actuator Single Phase 220V AC Operated Wafer Type Butterfly Valve with CI Body & amp; SS Disc2) Level Float Switch- 5M 3) Control Box - * IP 55 Finishing(250 x 160 x 115) , * LED Lamps: Tank FULL, Tank EMPTY, Power, * Power supply toggle switch, * Accepts 230V Single Phase power supply and provides 24VAC to float switch and 230VAC to valve coil., * Accepts O/NC feedback from float switch.

Description of Work / Item(s)

Amount

Part A Interior

SITC of Acoustic Slated wall cladding Acoustic slat wall cladding system made up of laminated/melamine-faced class E1 MDF slats. The slats shall have grooves at a distance of 20-30mm pitch throughout the wall cladding. The wall cladding shall have superior acoustic levels by using porous textures with Helmholtz resonators and shall adhere to the highest health and safety standards. The panel shall have extremely low formaldehyde content. The slated wall cladding shall be greenguard gold tested/certified (from UL / Intertek). The slat system shall be suitable for applications on curved shapes which shall be achieved by creating a slight angle between each slat. The angular adjustment shall be less visible and shall give the impression of a curved line rather than a series of segments. The rear side of the slat shall have holes to create a flat absorption curve and give a very even acoustic effect across the frequency range. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Acoustic Modular metal acoustic batten panelling 1. Modular acoustic metal batten paneling of 1”x1” made up of extruded aluminum with “T-groove for click-on system”. Extruded Aluminum must be finished with PVC free material and Textured wooden finish shall be provided. Sublimation/Heat transfer method shall not be used to achieve better scratch resistance. 2. Die casted click on joinery shall be used with spring system for fixing to be used for improved rigidity. 3. The structure system shall have grooves to insert polyethylene terephthalate acoustic board. 4. The paneling shall have superior acoustics and shall adhere to the highest health and safety standards. Same system can be installed on curvilinear wall as per the design requirements. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Decorative acoustic parallelogram metal wall paneling 1. Computationally generated acoustic metal Wall paneling form, made up of factory-made removable type self-inter-lockable metal panels with a front sheet of preformed textured hot-dip galvanized sheet with rigid polyvinylchloride (PVC) film on one side and on the other side a coating to avoid rust (sheet thickness 0.6mm & PVC Coating at least 0.11mm). The back cover of the panel shall be made up of a 0.6mm thick CRCA/GI sheet of approved colour. The panelling design shall comprise of a specially designed micro perforated and non-perforated panels through CNC laser cutting, bending & punching. The panelling/partition shall be greenguard certified/tested (from UL/Intertek). Panels shall be designed to achieve shape and design as per the design consultant and shall be fixed using GI/CRCA hook fitting on the structure. Overall system thickness for panelling shall be 60 to 90mm and for partition shall be 70 to 120mm. 2. Remaining structure shall be the same as per modular rigid PVC metal panelling (Sr No. 1 modular rigid PVC metal panelling). Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Modular Acoustic Printed Metal Paneling 1. The printed panelling shall have the same technical specifications as that of acoustic metal panelling (Wall Finishing - Sr No. 1 modular rigid PVC metal panelling). However, in addition to it, the front tile shall be digitally printed. Graphics shall be approved by the Customer. 2. Digital printing shall be done on modular metal Panelling. Pasting stickers/flex/vinyl on metal tile shall be deemed unacceptable. 3. The structure shall be made from a modular, heavy-duty powder-coated CRCA frame (minimum sheet thickness 1mm) and shall allow an uninterrupted flow of wires/cable/tubes of maximum diameter 25mm. 4. The structure shall be securely connected from the wall, roof and floor. It shall be made up of a minimum of 1mm thick vertical slotted rolled C sections (Upright) and horizontal rolled ‘C’ connectors. Grid of the desired dimension shall be formed by Vertical and horizontal sections having 20 to 50mm pitch. 5. For Structure: - Powder coated CRCA steel sheet. (Sheet thickness minimum 1.0mm with powder coating). Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Metal Rafters Metal rafter made up of a combination of two C sections. The overall panel size shall be of a minimum 75X200mm or as per Architect or EIC approval , the material shall be preformed textured PVC coated GI sheet panels. The sheet thickness shall be a minimum of 0.6mm. The material shall be similar to wall panelling tiles and shall be ASTM e84 tested (from UL / Intertek) for the surface burning characteristics. This is mandatory requirement from Fire safety point of view. The structure shall be made up of powder coated CRCA steel sheet. (Sheet thickness minimum 1.6mm). The powder coating thickness shall be 60 to 90 microns. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Modular glass partition with metal wire-raceway/skirting on top & bottom Glass partitions made of 12mm toughened glass installed over 100mm modular metal wire-raceway/skirting on the top & 450mm at the bottom. The modular metal wire-raceway/skirting shall have the same material as that of modular metal panelling/partition. The proper structure shall be made to ensure fixing of glass from RCC slab above the false ceiling and support on partition structure below. Straight & vertical structural members shall not be visible. Glass shall be fitted on anodized extrusion with tool-less technology and having a provision for replacing the glass with perforated sheet/acoustic tile by removing the glass. NOTE: - The nature of installation shall be replaceable, expandable, and flexible to cater to the future expansion/technical up-gradation. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Vinyl Poster Poster fixed on wall with applying adhesive. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Designer Privacy film for glass partitions & glass door The film to be installed on clear glass to provide the look of sandblasted glass. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of 12mm Glass Railing with stainless steel Fixing of 900mm high Side Fixed Handrail system including 10-12mm clear toughened glass railing with Customized SS 304 Railing system as per Customer’s approval. The glass shall be held with SS 304 stud with flat headed bolt single point spider fittings as per design. The 50 diameter SS pipe shall be held firmly with the 63.5x12 mm thick SS flat vertical bar through SS bracket at every junction with M4SS set screws. The entire assembly shall be fixed through two SS connect holder brackets. The system will be Complete as per requirement of site. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Metallic Door (with OR without Vision Panel) With door hinges and locking arrangements and both way handle. Prepare with rigid thermo fused film metal panels. Specification: 0.6mm thick Metal panel sheets, internal cavity filled with adequate quantity of honeycomb. Material of the partition and that of metal door will remain the same. Material of the partition and that of metal door will remain the same. The door thickness shall be minimum 45mm and frame thickness shall be minimum 115mm. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of 12mm thick frameless tempered clear glass door. 1) 12mm thick frameless tempered clear glass door 2) With door spring and locking arrangements and both way handle and patch fittings. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of designer flush door Door shall be made of 35mm thick core of block board construction decorative type, conforming to IS 2202 (Part-1). The shutters faced with both sides 3mm thick BWR grade plywood finished with 4mm thick veneer of approved make. 35x20mm second class Teak wood lipping shall be provided all around the shutter by means of approved quality neoprene-based adhesive and nailing @300mm (maximum). along with 100x75 mm second class teak wood frame with 125mm Stainless steel butt hinges conforming to IS12817 complete as per drawings. Veneer and teak wood lipping and frame shall receive melamine polish in two to three coats as per specifications and approval of Engineer in charge. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Acoustic Hexagonal Metal Ceiling 1. Designer composite ceiling with a combination of Perforated / Non-perforated / printed / backlit hexagonal tiles. 2. Perforated/non-perforated tiles shall be made up of metal panels of 0.6mm thick CRCA powder coated sheet. 3. To ensure restriction of hazardous substances; so that the final product does not contaminate the environment and we give a healthy life to our coming generations it is necessary that the ceiling system shall be RoHS certified/tested (from UL / Intertek). 4. Copy of Test certification/test report for ASTM E84 (from UL/Intertek) for the surface burning characteristics of non-perforated ceiling tiles. This is mandatory requirement from fire safety point of view. 5. Ceiling Panels shall be designed to achieve shape & design as per the design consultant designed to enhance visual feel, with provision for easy installation and maintenance, integrated lighting (for backlit tiles) and scope for integration of building services like HVAC and fire detection/ fighting system. 6. Ceiling Plank: 6.1 Light fitting can be defined as per the LUX requirement. 6.2 It shall have Laser cut hole for light fixing as per defined lux requirement and approved layout. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Designer acoustic customized metal ceiling 1. Providing & fixing of designer acoustic metal ceiling system consisting of customized powder coated tiles. 2. Tiles Perforation – To achieve acoustics without deteriorating the aesthetical appeal of the interior it is necessary that the at-least seventy five percent of the ceiling tiles have micro-perforations (less than 1.6mm dia. each) all over the surface with a density of 5000 holes per square feet. The ceiling tile to have clean perforations and provides a smooth finish on the front fascia of tiles. 3. The proposed ceiling metal tiles shall be Class A certified/tested as per ASTM e84 (from UL / Intertek) for surface spread of flame and smoke generation. This is mandatory to ensure that the materials used in the interiors do not provoke fire. 4. The ceiling shall have a Noise absorption coefficient (NRC) value of 0.60 according to IS:8225-1987, ISO: 354-1985 and ASTM 423-90. 5. To ensure restriction of hazardous substances; so that the final product does not contaminate the environment and we give a healthy life to our coming generations it is necessary that the modular metal ceiling system shall be RoHS certified/tested (from UL / Intertek). 6. The structure shall be made from a heavy-duty powder-coated CRCA steel sheet (minimum sheet thickness 0.8 to 1.6mm). It shall be securely grouted from the roof with help of an anchor fastener and GI self-threaded rods. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Designer Acoustic Metal False ceiling with Planks 1. Factory made acoustic modular metal false ceiling of powder coated panels. Make shall comprise of perforated and non-perforated metal panels made through CNC laser cutting, bending & punching. Panel shall be of 0.6mm CRCA sheet of approved powder coating finish. Panels shall be designed to achieve shape and design as per the design consultant with the combination of acrylic panels with lights, designed to enhance visual feel, with provision for easy installation and maintenance, integrated lighting and scope for integration of building services like HVAC and fire detection/ fighting system. Metal modular false ceiling shall have Noise absorption coefficient (NRC) value 0.60 according to IS:8225-1987, ISO: 354-1985 and ASTM 423-90. 2. It is well known that metal is resistant to fire as compared to wood & fabric. However, from fire and safety point of view, to ensure that the used material is not subjected to any kind of surface treatment which provokes fire. The proposed ceiling tiles shall be Class A certified/tested as per ASTM e84 (from UL / Intertek) for surface spread of flame and smoke generation. This is mandatory to ensure that the materials used in the interiors do not provoke fire. 3. To ensure restriction of hazardous substances; so that the final product does not contaminate the environment and we give a healthy life to our coming generations it is necessary that the modular metal ceiling system shall be RoHS certified/tested (from UL / Intertek). 4. Designer metal ceiling shall be greenguard gold certified/tested. 5. To avoid dark spots/areas in the room it is necessary that continuous linear lights are used across the width/length of the room. Audit certified design feature (from UL / Intertek) of integrated channel in ceiling for quick installation & replaceability of continuous linear light. The ceiling system having integrated inbuilt channel for installation of cove lights and shall permit quick and easy replacement of cove light without using any tools. Replacement to be carried out within 120 Seconds per meter. 6. Seismic safety of user & room equipment is a prime concern area. The metal ceiling shall sustain the seismic vibrations as per design spectrum IS 1893 for zone 2 vibrations or better. The test shall be carried out by authorized government agency. 7. Structure shall be made from heavy duty powder coated CRCA steel sheet (minimum sheet thickness 0.8 to 1.6mm). It shall be securely grouted from roof with help of anchor fastener and GI self-threaded rods. It shall be formed with the help of slotted rolled W sections (stiffener) and Master C section with help of M6 cage nut and bolts.Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Acoustic Metal baffle ceiling 1. The baffles shall be made up of CRCA powder coated sheet. These baffle planks shall be bent through CNC to have dimensions as 80X40mm or as per the design approval or as per EIC approval. 2. Centre to centre distance shall be minimum 80mm. 3. Designer metal baffle ceiling shall be Greenguard gold certified/tested (from UL / Intertek). 4. To ensure restriction of hazardous substances; so that the final product does not contaminate the environment and we give a healthy life to our coming generations it is necessary that the metal ceiling system shall be RoHS certified/tested (from UL / Intertek). 5. It is well known that metal is resistant to fire as compared to wood & fabric. However, from fire and safety point of view, to ensure that the used material is not subjected to any kind of surface treatment which provokes fire. The proposed ceiling tiles shall be class A certified/tested as per ASTM e84 (from UL / Intertek) for surface spread of flame and smoke generation. This is mandatory to ensure that the materials used in the interiors do not provoke fire. 6. Specifications (Finish and component details) 6.1 Ceiling Baffle tile: minimum 0.6mm thick CRCA powder coated sheet 6.2 Carrier made of 0.60 mm CRCA steel sheet, powder coated to matching baffle color or black as directed by the Customer. Ceiling to have arrangement to fix, hang and lock the baffles of required sizes and at required intervals. The punched carrier shall be used for suspension and fixing secondary channel. 6.3 The baffles top edge will have a flange to insert/fix in the carrier profile. 7. Suspension: The carriers would be placed at every 1200mm (maximum) and this secondary member in turn would be suspended by 6mm rod fixed to the slab by means of 6mm diameter, dash fastener. 7.1 Top clamp: 1mm thick CRCA steel Sheet for holding the threaded rod. 7.2 End Cap: minimum 0.5mm thick CRCA powder coated sheet. End cap similar to main ceiling baffle. 7.3 Entire structure will be in powder coated CRCA sheet. 7.4 Metal Strip where baffle planks will be hanged shall be sleek & sturdy. 8. Color: As per approval. 8.1 The structure system shall have grooves to insert polyethylene terephthalate acoustic board on the upper side of two adjacent baffles to achiever superior acoustics. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Designer Composite Acoustic metal ceiling 1. Factory made acoustic modular composite false ceiling with a combination of 2/3 dimensional, Perforated/Non-perforated/backlit ceiling tiles. 2. 3 dimensional Perforated/non-perforated tiles shall be made up of metal panels of minimum 0.6mm thick CRCA powder coated sheet. 3. 2 dimensional ceilings shall be made up of wooden textured Preformed Textured Hot dip galvanized strips and sheets of low carbon steel coated on one side with rigid polyvinylchloride (PVC) film and on the other side a coating based on cross linkable polyester resins (sheet thickness 0.6mm & PVC Coating 0.15mm). 4. The backlit tiles shall be having a 3-dimensional profile to enhance the visual feel. 5. The metal ceiling tiles shall be made through CNC laser Cutting, bending & punching. Panels shall be designed to enhance visual feel, with provision for easy installation and maintenance, integrated lighting and scope for integration of building services like HVAC and fire detection/ fighting system. 6. All the fasteners shall be hidden and nuts/bolts shall not be visible on the exposed surface. Supporting structure shall be made from heavy duty powder coated modular steel frame.Structure shall be securely grouted from wall and roof. It shall be made up of heavy-duty sections of mild steel. Tiles shall be easily replaceable to access above ceiling services. 7. As per design panel shall comprise of perforation for making false ceiling acoustically sound with acoustical fleece. 8. To ensure restriction of hazardous substances; so that the final product does not contaminate the environment and we give a healthy life to our coming generations it is necessary that the metal ceiling system shall be RoHS certified/tested (from UL / Intertek). 9. Designer metal ceiling shall be Greenguard gold certified/tested (from UL / Intertek). 10. It is well known that metal is resistant to fire as compared to wood & fabric. However, from fire and safety point of view, to ensure that the used material is not subjected to any kind of surface treatment which provokes fire. The proposed metal ceiling tiles shall be Class A certified/tested as per ASTM e84 (from UL / Intertek) for surface spread of flame and smoke generation. This is mandatory to ensure that the materials used in the interiors do not provoke fire. 11. To ensure restriction of hazardous substances; so that the final product does not contaminate the environment and we give a healthy life to our coming generations it is necessary that the ceiling system shall be RoHS certified (from UL / Intertek). 12. Copy of Test certification for ASTM E84 (from UL/Intertek) for the surface burning characteristics of non-perforated ceiling tiles. This is mandatory requirement from fire safety point of view. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Hexagonal Designer Acoustic Metal ceiling 1. Designer hexagonal ceiling shall be installed over extruded aluminium profiles joined together to form a rigid structure. 2. The tile shall be made up of metal panels of Preformed Textured Hot dip galvanized strips and sheets of low carbon steel coated on one side with rigid polyvinylchloride (PVC) film and on the other side a coating based on cross linkable polyester resins (sheet thickness 0.6mm & PVC Coating 0.15mm). 3. Ceiling tiles shall be designed to achieve shape and design as per the design consultant with a provision to integrate illumination channel at the edges to enhance visual feel. These channels shall have provision for easy installation, removal & replacement for quick and easy maintenance. The ceiling tiles shall permit integration of building services like HVAC and fire detection/ fighting system. 4. As per design, few of the panels shall comprise of micro perforation for making false ceiling acoustically sound. 5. Approximately 10 % tiles shall have acoustic wrapped fabric fully upholstered on all side. The fabric shall be washable and should withstand normal wear and tear for 10 years. Fabric Make : Sprint from Camira or Equivalent (shade as per customer approval) 5.1 To ensure restriction of hazardous substances; so that the final product does not contaminate the environment and we give a healthy life to our coming generations it is necessary that the metal ceiling system shall be RoHS certified (from UL / Intertek). 5.2 From fire and safety point of view, to ensure that the used material is not subjected to any kind of surface treatment which provokes fire. The proposed metal tiles shall be Class A certified as per ASTM E84 (from UL/Intertek) for surface spread of flame & smoke generation. This is mandatory to ensure that the materials used in the interiors do not provoke fire. 5.3 Suitable understructure shall be made of at least 0.6mm mild steel sheet with powder coated finish. It shall be securely grouted from roof with help of anchor fastener and GI self-threaded rods. Suitable size punched carrier would be bent channel with holes for suspension and fixing channel. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Designer Acoustic Metal False ceiling (Vertical) 1. Factory made acoustic modular false ceiling of metal panels made up of Preformed Textured Hot dip galvanized strips and sheets of low carbon steel coated on one side with rigid polyvinylchloride (PVC) film and on the other side a coating based on cross linkable polyester resins (sheet thickness 0.6mm & PVC Coating 0.10mm). 2. Make shall comprise of perforated and non-perforated metal planks/tile (dimension as approved by Engineer In-charge) made through CNC laser cutting, bending & punching. Panel shall be of 0.6mm galvanized metal of approved color. Planks/tiles shall be designed to enhance visual feel, with provision for easy installation and maintenance and scope for integration of building services like HVAC and fire detection/ fighting system. 3. For non-perforated tiles, copy of Test certification for ASTM E84 (from UL/Intertek) for the surface burning characteristics of ceiling tiles. This is mandatory requirement from Fire safety point of view. Raw-material supplier data alone is not acceptable 4. As per design panel shall comprise of micro perforation for making false ceiling acoustically sound. 5. The plank/tiles shall be bent through CNC to have dimensions as 25mm(W) X 200 mm (Flange). 6. Centre to centre distance shall be minimum 80mm. 7. Structure shall be made from heavy duty powder coated CRCA steel sheet (minimum sheet thickness 0.8 to 1.6mm). It shall be securely grouted from roof with help of anchor fastener and GI self-threaded rods. 8. Ceiling Plank/tiles: 8.1 Plank/tiles shall be made from 0.6mm thick sheet of approved shade and sizes. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Baffle ceiling with provision of Integrated Illuminated channel 1. Modular baffle ceiling with curvilinear front fascia. 2. The baffles shall be made of GI/MS sheet or Aluminium. The ceiling baffles shall have provision of integrating illumination channel which shall be processed on machine to have dimensions to suit illumination requirement. 3. The finish of the material shall be Rigid PVC coated Galvanized-iron sheet. 4. To ensure restriction of hazardous substances; so that the final product does not contaminate the environment and we give a healthy life to our coming generations it is necessary that the metal ceiling system shall be RoHS certified (from UL/Intertek). 5. Suitable under structure shall be made of at least 0.6mm mild steel sheet, powder coated to matching baffle color. It shall be securely grouted from roof with help of anchor fastener and GI self-threaded rods. Ceiling to have arrangement to fix, hang & lock the baffles of required sizes and at required intervals. The suitable size punched carrier would be bent channel with holes for suspension and fixing channel. 6. Baffles shall be designed to achieve shape and design as per the design consultant with the acrylic panels with lights, designed to enhance visual feel, with feature of provision of integrated illumination channel for easy installation and maintenance. 7. Illuminated Baffle Ceiling plank shall have audit certified design feature of Integrated channel in ceiling for quick installation & replaceability of continuous linear light. The ceiling system having integrated inbuilt channel for installation of cove lights and shall permit quick and easy replacement of cove light. 8. The structure system shall have grooves to insert polyethylene terephthalate acoustic board on the upper side of two adjacent baffles to achiever superior acoustics. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Designer Acoustic Metal Plank False ceiling with Wooden Texture 1. Factory made acoustic modular false ceiling of metal panels made up of Preformed Textured Hot dip galvanized strips and sheets of low carbon steel coated on one side with rigid polyvinylchloride (PVC) film and on the other side a coating based on cross linkable polyester resins (sheet thickness 0.6mm & PVC Coating 0.15mm). 2. Make shall comprise of perforated and non-perforated metal panels (dimension as approved by Engineer In-charge) made through CNC laser cutting, bending & punching. Panel shall be of 0.6mm galvanized metal of approved color. Panels shall be designed to enhance visual feel, with provision for easy installation and maintenance and scope for integration of building services like HVAC and fire detection/ fighting system. 3. For non-perforated tiles, copy of Test certification for ASTM E84 (from UL/Intertek) for the surface burning characteristics of ceiling tiles. This is mandatory requirement from Fire safety point of view. Raw-material supplier data alone is not acceptable 4. As per design panel shall comprise of micro perforation for making false ceiling acoustically sound with fire rated acoustic fleece. 5. Ceiling Plank: 5.1 Plank shall be made from 0.6mm thick sheet of approved shade and sizes. 5.2 Light fitting can be defined as per the LUX requirement. 5.3 It shall have Laser cut circular hole for light fixing as per defined lux requirement and approved layout. 6 Properties: - 6.1 High NRC (Noise Reduction Co-efficient). Ceiling tiles must be a combination of perforated and non-perforated tiles to have Sound absorption coefficient (NRC) value 0.30 per IS:8225-1987, ISO: 354-1985 and ASTM 423-90. 6.2 Better Light reflectance & Fire performance. 6.3 Humidity Resistant. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Designer Acoustic Metal Ceiling of size 550X1150mm 1. Providing & fixing of Designer metal ceiling of powder coated tiles of minimum size 550X1150mm. 2. Tiles Perforation – To achieve acoustics without deteriorating the aesthetical appeal of the interior it is necessary that the at-least twenty five percent of the ceiling tiles have micro-perforations (less than 1.6mm diameter each) all over the surface with a density of 5000 holes per square feet. The ceiling tile to have clean perforations and provides a smooth finish on the front fascia of tiles. 3. The proposed ceiling metal tiles shall be Class A certified/tested as per ASTM e84 (from UL / Intertek) for surface spread of flame and smoke generation. This is mandatory to ensure that the materials used in the interiors do not provoke fire. 4. To ensure restriction of hazardous substances; so that the final product does not contaminate the environment and we give a healthy life to our coming generations it is necessary that the modular metal ceiling system shall be RoHS certified (from UL / Intertek). 6. The structure shall be made from a heavy-duty powder-coated CRCA steel sheet (minimum sheet thickness 0.8 to 1.6mm). It shall be securely grouted from the roof with help of an anchor fastener and GI self-threaded rods. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Stretched fabric Panels suspended from Roof Stretched fabric ceiling shall be installed over minimum 60 mm wide heavy duty extruded aluminium frame with die cast aluminium corners. Self-tensioned spring system shall keep the fabric surface in a perfectly stretched condition. The fabric shall not be installed/pasted/ glued/bolted on any flat surface. There shall be air gap of at least 10mm between the fabric and the acoustic material. Fabric shall not be affected by humidity or temperature. The frames shall have flexibility to achieve any, size, and angle of inclination. Length of ceiling shall be minimum 200mm and maximum 6000mm. Aluminium frame shall allow easy removal & re-upholster whenever required. The fabric shall be tested by independent engineering companies to achieve acoustical performance. Fabric shall have light fastness of 5 as per ISO 105 - B02 and flammability standard to adhere BS 476 Part 6 Class 0. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Fabric Artistic Parametric Ceiling 1. Acoustical fabric ceiling made up of minimum 3 mm thick non-woven thermo formable pes fibers, press-fitted on metal understructure by gravity assisted hooks. 2. The structure shall be made up of GI / CRCA sheet / extrusions 3. The fabric tile shall have minimum size of 500mm X 300mm and shall permit multiple design patterns in three dimensions. 4. The panels shall provide flexibility of 3-4 different patterns without changing the panels/tiles. 5. The panel should retain the three-dimensional shape without using any external element/frames/joineries. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Acoustic Laminate flooring To avoid distraction of users because of unwanted noise generated from movement of chairs/people in the room it is necessary that the proposed flooring shall damp such impact noises. Acoustic flooring (shall reduce impact sound by 14dB (ISO 717-2)). It shall be twin-layer linoleum built up from minimum 2mm acoustic laminate and a 2mm corkment backing. Flooring shall be decorative type of approved shade, pattern, texture, and design and of approved manufacturer. Dimensions shall be as per the final approved design and site requirement. Flooring shall be laid over concrete floor with laying compound strictly as per manufacturer’s specification. The designer acoustic flooring shall be Greenguard gold tested / certified. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Carpet Flooring Minimum 4 mm thick acoustic carpet flooring shall meet the requirement of EN 1307 (shall have Impact sound Lw = 19 dB as per (ISO 717-2)). The floor must be resistant to fungal growth. Flooring shall be decorative type of approved shade, pattern, texture and design and of approved manufacturer with sound absorption of 0.1 as per ISO 354. Dimensions shall be as per the final approved design and site requirement. Flooring shall be laid over concrete floor with laying compound strictly as per manufacturer’s specification of makes given. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Granite Stone for floor Highlighter/steps Granite Stone for floor Highlighter/steps in required design and pattern, with 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) laid and joint with white cement slurry including pointing with white cement slurry admixed with pigment of matching shade as directed by the Engineer-in-Charge. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Vitrified Flooring Fully vitrified, 8mm thick non-porous, homogenous, abrasion resistant, minimum size 600 mm x 600 mm x 8mm of approved colour and shall be laid over concrete floor with laying compound strictly as per makes given. Total thickness of the flooring shall be 40mm thick including the thickness of the tiles, under bed. Tiles will be laid with 2 mm gap using spacers and gap will be filled with black colour epoxy latictere. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Combination floor (Italian Marble Botticino and Black/Nero Marquina) 1. The best quality Pre-polished Italian marble stone from approved quarry shall be machine cut and machine polished as specified in respective items and shall be of specified thickness and of approved quality and size, free from cracks and flakes and shall be uniform colour, with straight edges. The sides of machine cut, and machine polished stones shall have perfect right angles and surface smooth. The stone slabs shall be laid and finished on bedding of cement mortar 1:4 (1 cement: 4 coarse sand) 20 mm (average) thickness. 2. The flooring work will be inclusive of 100mm high skirting which shall be flushed with the wall & with a 5mm high groove above it. 3. The Italian marble skirting to be laid on min 20mm thick cement mortar of ratio 1:3 (1 cement: 3 coarse sand) and joined with white cement slurry mixed with matching colour. 4. The finished stone surface thus laid to the required degree as approved by the Engineer in charge. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

Part B Furniture

SITC of Reception Counter (Type 1) 1) The furniture work surface shall be straight in shape to maintain grand aesthetic appeal. It shall be made of minimum 25mm thick MDF finish. 2) The structure shall be made up of powder coated steel / Extruded Aluminum Alloy / MDF / board finish. 3) The working side edge: - Audit certified design (from UL/Intertek) feature on front modular polyurethane (PU) edge. High density polyurethane foam molded on industrial grade aluminum core to form minimum 50mm deep tapered edge to be installed on worktop. The edge shall be mechanically replaceable within 30 minutes in case of damage or wear without opening or removing the top. 4) It shall have provision of electrical and Lan sockets with concealed wiring. 5) Design as per engineer in charge approval. Approximate minimum Dimensions – 3000mm(W) X 750mm(D) X 750mm(H). Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Reception counter 1) The furniture work surface shall be straight in shape to maintain grand aesthetic appeal. It shall be made of minimum 25mm thick laminated MDF. 2) The structure shall be made up of powder coated steel / Extruded Aluminum Alloy / MDF / board finish. 3) The working side edge: - Audit certified design (from UL/Intertek) feature on front modular Polyurethane (PU) Edge. High density Poly Urethane Foam moulded on industrial grade aluminum core to form minimum 50mm deep tapered edge to be installed on worktop. The edge shall be mechanically replaceable within 30 minutes in case of damage or wear without opening or removing the top. 4) It shall have provision of Electrical and Lan sockets with concealed wiring. 5) Design as per Engineer In charge Approval. Approximate minimum dimensions – 1800mm(W) X 750mm(D) X 750mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of 3-Seater Sofa The top shall be of Upholstery with PU Finish. The sofas are made of solid wood base, reinforced with supportive addendum in the seat. Engineered wood panels form/support the overall design structure, they synergize with the solid wood to offer unparalleled life to the product. Foam padding of multi-density and varying thicknesses provide cushion for the sofa. PU foam used is made Hennecke foam plants using German Technology capable of producing the high-quality flexible polyurethane foam. It provides unparalleled comfort, ease of use and durability. The foam used is 32 Density for seating areas and 28 Density for backrest. The super soft foam used is in seating areas in 32-35 Density High-resilience (HR) foam which is unique and rarely used by manufacturers. Webbing: Interwoven high tensile elastic bands for optimum comfort and endurance. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Center unit for sofa Centre unit top shall be made up of glass and the frame work shall be made up of wood. Approximate minimum dimensions – Length (110 cm), Width (60 cm), Height (45 cm) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Center unit for Collaborative Seating Stools 25mm thick MDF top for center unit for sofa with injection molded polyurethane nosing on profiled wooden core. Understructure shall be made up of laminated board / sheet metal. Approximate minimum Dimensions – 600mm(Dia) X 600mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Center unit (Type – 2) 25mm thick MDF top for center unit for sofa with injection molded polyurethane nosing on profiled wooden core. Understructure shall be made up of laminated board / sheet metal. Approximate minimum Dimensions – 800mm(W) X 450mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Chair Type 1 Single Lever Adjustment Tension Control Tilt Lock Automatic Lumbar Support Synchro-Tilt Mechanism Seat Height Adjustment Waterfall Seat Back Height Adjustment Seat Depth Adjustment Arm Height, Depth & Swivel Adjustment Headrest with Height and Angle Adjustment All parts of the chair are replaceable and kept in stock for longer life-Cycle 97% Recyclability Greenguard Certified Meets EN5459, EN 1335-2: 2009 and EN 1335-3:2009 ANSI/BIFMA X5.1 Certified Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Chair Type 2 High Back with Mesh Backrest, Synchronized Mechanism, Adjustable Armrest, Gaslift for Seat height adjustment, Standard 5-prong Nylon Base. Seat: Fabric, Backrest – mesh, Greenguard Certified, ANSI/BIFMA X5.1 certified. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Chair Type 3 Medium Back Mesh Back, Silver Epoxy Backbone, Synchronized Mechanism, 3-Way Adjustable Armrest, Gaslift for Seat height adjustment, Standard 5-prong nylon Base, Seat - Fabric and mesh backrest, Greenguard Certified, ANSI/BIFMA X5.1 certified. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Chair Type 4 Low back visitor model ABS for seat, Mesh back with extra lumber Support with fine tuning for depth adjustment, with fixed armrest, silver epoxy cantilever base Upholstery: Black Fabric Seat & mesh backrest Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Auditorium Chair Mid-back Auditorium Chairs (Fixed Type). Color of the same shall be finalized during the engineering finalization phase. The color which goes well with the interiors and suitable for the overall aesthetics of the room shall be considered. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Collaborative Seating Stools It shall have acoustic wrapped fabric fully upholstered on all side. The fabric shall be washable and should withstand normal wear and tear for 5 years. Fabric Make: Camira (Sprint) / Sunbury / Kvadrat / Response. Approximate minimum Dimensions – Ø410*430mm Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Single Seater sofa chair without Arm, SS Base Stand, Gas Lift, Leatherette Tapestry. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Meeting desk 1) 25mm thick MDF top for center unit for sofa with injection molded polyurethane nosing on profiled wooden core. 2) Understructure shall be made up of laminated board / sheet metal. Approximate minimum dimensions – 1000mm (W) X 1000mm(D) X 750mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Open Collaborative Meeting It shall be designed for minimum 4 people; it shall have acoustic wrapped fabric fully upholstered on inner and outer side. The countertop at the center shall have laminate finish. The edges shall have 40-50 mm deep molded polyurethane edge. The entire structure shall be self-standing without any need of grouting. It should be designed with Ergonomics in mind. Optional integrated power socket under seat. The fabric shall be washable, appropriate for task seating and should withstand normal wear and tear for 5 years. Fabric Make: Camira (Sprint) / Sunbury / Kvadrat / Response. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Open Collaborative conference It shall be designed for minimum 4 / 6 / 8 people; it shall have acoustic wrapped fabric fully upholstered on inner and outer side. The countertop at the center shall have laminate finish. The edges shall have 40-50 mm deep molded polyurethane edge. The entire structure shall be self-standing without any need of grouting. It should be designed with Ergonomics in mind. Optional integrated power socket under seat. The fabric shall be washable, appropriate for task seating and should withstand normal wear and tear for 5 years. Fabric Make: Camira (Sprint) / Sunbury / Kvadrat / Response. Approximate minimum Dimensions – 2400mm(W) X 1500mm(D) X 1800mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Conference Desk 1) The conference/meeting room furniture shall conform to high standard of engineering as mentioned in the document; meeting the specified codes, standards and designs. 2) The furniture top shall be made up of minimum 25mm thick MDF board with molded Polyurethane (PU) Edge. 3) The under structure shall be made up of 18mm thick MDF board with 2mm thick PVC edge banding tape. 4) Accessories: Flap 5) The conference room furniture shall be Greenguard gold tested/certified (from UL / Intertek). 6) Cable Trays and Wiring: - The furniture shall be designed with cable trays to allow for continuous & concealed cable management across the furniture. Approximate minimum Dimensions – 5400mm (W) X 1800mm (D) X 750mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Cabin Desk (Type 1) 1) The furniture top shall be made up of minimum 25mm thick MDF board. 2) The working side edge: - Audit certified design (from UL/Intertek) feature on front modular Polyurethane (PU) Edge. High density Poly Urethane Foam moulded on industrial grade aluminum core to form minimum 50mm deep tapered edge to be installed on worktop. The edge shall be mechanically replaceable within 30 minutes in case of damage or wear without opening or removing the top. 3) The under structure and complete structure shall be made up of 18mm thick MDF board. 4) The furniture is equipped with handles for easy opening along with soft closing drawers. The Construction shall be of high quality MDF board. 5) The furniture top shall have power box with access flap for wire management. The design shall be as per attached image and as per the Engineer in charge approval. 6) The desk shall be Greenguard gold tested/certified (from UL / Intertek). Table – 1500mm(W) X 750mm (D) X 750mm(H) Side Runner – 900mm(W) X 450mm(D) X 750mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Cabin Desk (Type 2) 1) The furniture top shall be made up of minimum 25mm thick MDF board. 2) The working side edge: - Audit certified design (from UL/Intertek) feature on front modular Polyurethane (PU) Edge. High density Poly Urethane Foam moulded on industrial grade aluminum core to form minimum 50mm deep tapered edge to be installed on worktop. The edge shall be mechanically replaceable within 30 minutes in case of damage or wear without opening or removing the top. 3) The under structure and complete structure shall be made up of 18mm thick MDF board. 4) The furniture is equipped with handles for easy opening along with soft closing drawers. The Construction shall be of high quality MDF board. 5) The furniture top shall have power box with access flap for wire management. The design shall be as per attached image and as per the Engineer in charge approval. 6) The desk shall be Greenguard gold tested/certified (from UL / Intertek). Table – 1500mm(W) X 750mm (D) X 750mm(H) Side Runner – 900mm(W) X 450mm(D) X 750mm(H) Back Runner – 1500mm(W) X 450mm(D) X 750mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Cabin Desk (Type 3) 1) The furniture top shall be made up of minimum 25mm thick MDF board. 2) The working side edge: - Audit certified design (from UL/Intertek) feature on front modular Polyurethane (PU) Edge. High density Poly Urethane Foam moulded on industrial grade aluminum core to form minimum 50mm deep tapered edge to be installed on worktop. The edge shall be mechanically replaceable within 30 minutes in case of damage or wear without opening or removing the top. 3) The under structure and complete structure shall be made up of 18mm thick MDF board. 4) The furniture is equipped with handles for easy opening along with soft closing drawers. The Construction shall be of high quality MDF board. 5) The furniture top shall have power box with access flap for wire management. The design shall be as per attached image and as per the Engineer in charge approval. 6) The desk shall be Greenguard gold tested/certified (from UL / Intertek). Table – 2100mm(W) X 750mm (D) X 750mm(H) Side Runner – 900mm(W) X 450mm(D) X 750mm(H) Back Runner – 2100mm(W) X 450mm(D) X 750mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of SITC of Director/Principal Furniture 1) The furniture shall consist of complete package Main furniture, side storage and back storage. 2) The furniture top shall be made up of minimum 36mm thick veneer with PU finish. 3) The working side edge: - Audit certified design (from UL/Intertek) feature on front modular Polyurethane (PU) Edge. High density Poly Urethane Foam moulded on industrial grade aluminum core to form minimum 50mm deep tapered edge to be installed on worktop. The edge shall be mechanically replaceable within 30 minutes in case of damage or wear without opening or removing the top. 4) The under structure and complete structure shall be made up of 18mm thick veneer with PU finish. 5) The furniture is equipped with handles for easy opening along with soft closing drawers. The Construction shall be of high quality MDF board. 6) The furniture top shall have power box with access flap for wire management. 7) The design shall be as per attached image and as per the Engineer in charge approval. 8) Approximate minimum dimensions Table – 2400mm(W) X 1000mm (D) X 750mm(H) Side Runner – 1200mm(W) X 450mm(D) X 750mm(H) Back Runner – 2400mm(W) X 450mm(D) X 750mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Workstation Desk Type 1 1) Linear shape tabletop shall be of 25 mm thick MDF board. 2) The working side edge: - Audit certified design feature on front modular Polyurethane (PU) Edge. High density Poly Urethane Foam moulded on industrial grade aluminum core to form minimum 50mm deep tapered edge to be installed on worktop. The edge shall be mechanically replaceable within 30 minutes in case of damage or wear without opening or removing the top. 3) Legs: Ergonomically designed and matching with the open office concept. The leg is made out of sheet metal. 4) The screen shall be made of minimum 8mm thick frosted acrylic or fabric panel. 5) Under structure pipe shall be made up of minimum 1.6mm thick CRCA Laser cut components, powder coated with the matching shade/color/finish. 6) Cable tray: Shall be made up of 1mm thick CRCA sheet, Cable tray is used for running the wires between the desk. Powder coating as per RAL shade incompliance with IS standard (CRCA sheet: IS 513, Powder Coating ISI 01). Provision of switch socket and wire flow can be made as per requirement of Engineer in charge. 7) Accessories: Flap with provision of Switch and Socket. 8) The desk shall be Greenguard gold tested/certified (from UL / Intertek). Approximate minimum Dimensions – 1200mm (W) X 600mm(D) X 750mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Workstation Desk Type 2 1) Y shape design desk. Tabletop shall be of 25 mm thick MDF board. 2) The working side edge: - Audit certified design (from UL/Intertek) feature on front modular Polyurethane (PU) Edge. High density Poly Urethane Foam moulded on industrial grade aluminum core to form minimum 50mm deep tapered edge to be installed on worktop. The edge shall be mechanically replaceable within 30 minutes in case of damage or wear without opening or removing the top. 3) Legs: Ergonomically designed and matching with the open office concept. The leg is made out of sheet metal. 4) The screen shall be made of minimum 8mm thick frosted acrylic or fabric panel. 5) Under structure pipe shall be made up of minimum 1.6mm thick CRCA Laser cut components, powder coated with the matching shade/color/finish. 6) Cable tray: Shall be made up of 1mm thick CRCA sheet, Cable tray is used for running the wires between the desk. Powder coating as per RAL shade incompliance with IS standard (CRCA sheet: IS 513, Powder Coating ISI 01). Provision of switch socket and wire flow can be made as per requirement of Engineer in charge. 7) Accessories: Flap with provision of Switch and Socket. 8) The desk shall be Greenguard gold tested/certified (from UL / Intertek). 9) Approximate minimum Dimensions – 1000mm(W1) X 1000mm(W2) X 500mm(D) X 750mm(H). Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Workstation Desk Type 3 1) Designer tabletop shall be of 25 mm thick MDF board. 2) The working side edge: - Audit certified design (from UL/Intertek) feature on front modular Polyurethane (PU) Edge. High density Poly Urethane Foam moulded on industrial grade aluminum core to form minimum 50mm deep tapered edge to be installed on worktop. The edge shall be mechanically replaceable within 30 minutes in case of damage or wear without opening or removing the top. 3) Legs: Ergonomically designed and matching with the open office concept. The leg is made out of sheet metal. 4) The screen shall be made of minimum 12mm thick frosted acrylic or fabric panel. 5) Under structure pipe shall be made up of minimum 1.6mm thick CRCA Laser cut components, powder coated with the matching shade/color/finish. 6) Cable tray: Shall be made up of 1mm thick CRCA sheet, Cable tray is used for running the wires between the desk. Powder coating as per RAL shade incompliance with IS standard (CRCA sheet: IS 513, Powder Coating ISI 01). Provision of switch socket and wire flow can be made as per requirement of Engineer in charge. 7) The spine shall be made up of aluminum extrusion/CRCA frames. The extrusions/frames shall be duly powder coated with 40+ microns over all surfaces. 8) The desk shall be greenguard gold tested/certified (from UL / Intertek). 9) Accessories: Flap with provision of Switch and Socket. Approximately minimum Dimensions – 1600mm (W) X 600mm (D) X 750mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Metal Storage Versatile 3-drawer office storage system solution shall be made up of 0.8mm ‐ 1mm CRCA sheets with powder coated finish. The drawers are meant to store stationary items like pens, calculators, staplers, files, folders, documents etc. It comes with sliding drawers and single lock operation along with caster wheels for 360‐degree movement. The storage shall be greenguard gold tested/certified (from UL / Intertek). Approximate minimum Dimensions – 420mm(W) X 450mm(D) X 550mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Side Metal Storage Side metal storage shall be made up of 0.8mm ‐ 1mm CRCA sheets with powder coated finish. The drawers and shutter are meant to store stationary items like pens, calculators, staplers, files, folders, documents etc. It comes with sliding drawers and openable shutter along with caster wheels for 360‐degree movement. The side metal storage shall be Greenguard gold tested/certified (from UL / Intertek). Approximate minimum Dimensions – 900mm(W) X 450mm(D) X 550mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Library counter 1) The furniture work surface shall be straight in shape to maintain grand aesthetic appeal. It shall be made of minimum 25mm thick laminated MDF. 2) The structure shall be made up of powder coated steel / Extruded Aluminum Alloy / MDF / board finish. 3) The working side edge: - Audit certified design (from UL/Intertek) feature on front modular Polyurethane (PU) Edge. High density Poly Urethane Foam moulded on industrial grade aluminum core to form minimum 50mm deep tapered edge to be installed on worktop. The edge shall be mechanically replaceable within 30 minutes in case of damage or wear without opening or removing the top. 4) It shall have provision of Electrical and Lan sockets with concealed wiring. 5) Design as per Engineer In charge Approval. Approximate minimum dimensions – 1800mm(W) X 750mm(D) X 750mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Library table 1) Table top shall be of 25 mm thick MDF board. 2) The working side edge: - Audit certified design (from UL/Intertek) feature on front modular Polyurethane (PU) Edge. High density Poly Urethane Foam moulded on industrial grade aluminum core to form minimum 50mm deep tapered edge to be installed on worktop. The edge shall be mechanically replaceable within 30 minutes in case of damage or wear without opening or removing the top. 3) The understructure shall be made up of sheet metal. Approximate minimum Dimensions – 1050mm(W) X 1050mm(D) X 750mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of reading desk 1) The reading room furniture shall conform to high standard of engineering as mentioned in the document; meeting the specified codes, standards and designs. 2) The furniture top shall be made up of minimum 25mm thick MDF board with molded Polyurethane (PU) Edge. 3) The under structure shall be made up of 18mm thick MDF board with 2mm thick PVC edge banding tape. 4) Accessories: Flap Approximate minimum Dimensions – 3800mm (W) X 2400mm (D) X 750mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Library Chair Low back library model ABS for seat, Mesh back with extra lumber Support with fine tuning for depth adjustment, with fixed armrest, silver epoxy cantilever base Upholstery: Black Fabric Seat & mesh backrest. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Glass book shelf Glass book shelf made of 0.8mm cold rolled closed annealed (CRCA) sheet with prime epoxy powder coat comply, Door will be 1mm CRCA sheet framing and 5mm toughened glass concealed through rubber gromet, the shelves unit fixed double right angle bended to avoid scratches (load carrying capacity of 20 kg/each shelf). Construction of glass book shelf will be revited joints for easy construction and finish & side panel slotted for adjustable shelves & D-Type chrome finished handles, cylindrical fulcrum type locks upward lifting: mechanical mechanism of rod used to be for door uplifting & M6 Threaded top groove rod with ABS molded foot leveling. Approximate Dimensions: 1200mm(W) X 450mm(D) X 1800mm(H). Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Low Height Storage Flat pack made up of minimum 0.6mm CRCA powder coated finish with hinged doors and adjustable shelves for different file heights. The storage shall be greenguard gold tested/certified. Approximate minimum Dimensions – 750mm(W) X 450mm(D) X 750mm(H) . Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Medium Height Storage Flat pack made up of minimum 0.6mm CRCA powder coated finish with hinged doors and adjustable shelves for different file heights. The storage shall be greenguard gold tested/certified. Approximate minimum Dimensions – 900mm(W) X 450mm(D) X 1200mm(H) . Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of 4 door locker 1) Size: 1830H x 380W x 450D, 2) Material: Cold rolled closed annealed (CRCA) sheet, 3) Thickness: 0.8 mm, 4) Finish: Epoxy powder coat comply, 5) Door: Perforation on lockers doors, 6) Fixed Shelves, 7) Construction: Revited joints for easy construction and finish & side panel, 8) slotted for adjustable shelves, 9) Locks: Cylinderical fulcrum type locks, 10) Hinges: 5-knuckle, full loop, tight pin style, securely welded to frame, 11) Foot leveling: M6 Threaded top groove Rod with ABS molded. For details refer the technical specification of Interior & Furniture Works - Sr. No. 44 4 door locker

SITC of Compactor 2 Bay Compactor Single Fixed Unit - 1 Nos. Single Mobile Unit - 1 Nos. Twin Mobile - back-to-back units - 2 Nos. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Podium The podium console must be modular with 25mm thick MDF table top with high pressure laminate finish. Understructure shall be made up of heavy duty Extruded Vertical and Horizontal Aluminum profiles of HE9WP grade. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of New Modular Test Bench 1) Test Bench shall conform to high standard of engineering as mentioned in the document; meeting the specified codes, standards and designs 2) Table-top: - The material of the working surface should be minimum 25mm thick MDF with edge banding finish. 3) Structure: - Made of Extruded Vertical and Horizontal Aluminium profiles of HE9WP grade. The Extrusions shall be duly powder coated with 40+ micron over all surfaces. All sheet metal parts must be finished with a durable, black, electrostatic powder coating. The structure shall be rigid enough 4) Back panel: - Back Panel made up of MS-Sheet CRCA Sheet with powder coated finish. 5) Side panel: - Side Panel made up of MS-Sheet CRCA Sheet with powder coated finish. 6) The manufacture shall be FSC certified. The necessary certificate / test report valid on the bid date and to be submitted within seven days from the date of purchase order. Approximate minimum Dimensions – 750mm (H) X 1200mm (W) X 750mm (D). Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of dining counter with integrated seating 1) The dining furniture shall have granite top of minimum 12mm thick. 2) The understructure shall be made up of stainless steel (SS304). 3) The seats shall be made up of stainless steel and shall be fixed on same understructure. 4) Approximate minimum dimensions – 1800mm(W) X 800mm(D) X 750mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of dining counter with integrated seating 1) The dining furniture shall have granite top of minimum 12mm thick. 2) The understructure shall be made up of stainless steel (SS304). 3) The seats shall be made up of stainless steel and shall be fixed on same understructure. 4) Approximate minimum dimensions – 2400mm(W) X 800mm(D) X 750mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of dining counter with integrated seating 1) The dining furniture shall have granite top of minimum 12mm thick. 2) The understructure shall be made up of stainless steel (SS304). 3) The seats shall be made up of stainless steel and shall be fixed on same understructure. 4) Approximate minimum dimensions – 1200mm(W) X 800mm(D) X 750mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of 3-Seater Sofa Three Seater Sofa, Wooden Frame, SS Pipe Leg, Leatherette Size in mm - 1950(L) X 760(D) X 750(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Centre Table, 18mm Prelaminated particle board top, Annodize Aluminium Section Frame. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Chair (Type 1) High Back Chair, PP Arm, Gas Lift, Nylon Base, Seat & Back Mesh Tapestry, Synchro tilt Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Chair (Type 2) Medium Back Chair, PP Arm, Gas Lift, Nylon Base, Seat & Back Mesh Tapestry, Synchro tilt. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Chair Type 3 Visitor Chair, PU Arm, Pipe Stand, Seat & Back Mesh Tapestry,Silver Powder Coated. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Seminar Chair Seminar Chair, Push Back, PU Foam, PP Arm With Cup Holder, Fire Retardant Fabric Tapestry. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Cabin Desk 1) The furniture top shall be made up of minimum 25mm thick particle board with 2mm thick PVC edge banding tape. 2) The under structure and complete structure shall be made up of 18mm thick particle board. 3) The pedestal furniture is equipped with handles for easy opening along with soft closing drawers. 4) The furniture top shall have power box with access flap for wire management. The design shall be as per attached image and as per the Engineer in charge approval. Table – 1500mm(W) X 750mm (D) X 750mm(H) Side Runner – 900mm(W) X 450mm(D) X 750mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Cabin Desk 1) The furniture top shall be made up of minimum 25mm thick particle board with 2mm thick PVC edge banding tape. 2) The under structure and complete structure shall be made up of 18mm thick particle board. 3) The pedestal furniture is equipped with handles for easy opening along with soft closing drawers. 4) The furniture top shall have power box with access flap for wire management. The design shall be as per attached image and as per the Engineer in charge approval. Table – 2100mm(W) X 750mm (D) X 750mm(H) Side Runner – 900mm(W) X 450mm(D) X 750mm(H) Back Runner – 2100mm(W) X 450mm(D) X 750mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of conference/meeting table 1) The conference/meeting room furniture shall conform to high standard of engineering as mentioned in the document; meeting the specified codes, standards and designs. 2) The furniture top shall be made up of minimum 25mm thick prelaminated particle board with 2mm thick PVC edge banding tape. 3) The under structure shall be made up of 18mm thick prelaminated particle board with 2mm thick PVC edge banding tape. 4) Accessories: Flap 5) Cable Trays and Wiring: - The furniture shall be designed with cable trays to allow for continuous & concealed cable management across the furniture. Approximate minimum Dimensions – 5400mm (W) X 1800mm (D) X 750mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Side Runner Made up of 18mm thick Prelaminated Particle Board with 2mm thick PVC edge banding tape. The sider runner is combination of drawers and openable shutter. 900mm(W) X 450mm (D) X 550mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Low Height Storage Made up of 18mm thick Prelaminated Particle Board with 2mm thick PVC edge banding tape. Approximate minimum Dimensions – 750mm(W) X 450mm(D) X 750mm(H) . Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Medium Height Storage Made up of 18mm thick Prelaminated Particle Board with 2mm thick PVC edge banding tape. Approximate minimum Dimensions – 900mm(W) X 450mm(D) X 1200mm(H) . Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of BMS room modular Control Desk with provision of 02 monitor, 01 CPU, 01 Operator & 01 Keyboard - 1200mm (W) X 1000mm(D) X 750mm(H) 1) The control desk solution shall conform to high standard of engineering as mentioned in the document; meeting the specified codes, standards and designs. It shall be capable of performing 24X7 operations under the specified environmental condition in compliance to control room ergonomic norms i.e. ISO 11064. 2) The EPD (Environmental product declaration) of control desk shall be verified in accordance with ISO 14025 (from UL / Intertek) for Impacts on Environment by Console. 3) Seismic safety of user & control room equipment is a prime concern area. Control Desk shall be tested and qualified to sustain Seismic vibrations as per design spectrum IS 1893 for zone 4 vibrations with monitor mounted on monitor arms of the console. Seismic test report of bare control desk shall be deemed unacceptable. This test shall be carried out by authorised government agency. 4) Ergonomic compliance report as per latest ergonomic norms of ISO 11064 to be submitted along with the bid. Being one of its kind facilities; the control room deserves a tested & proven product having genuine design. As a proof of supplier’s commitment towards the product it is mandatory that the control desk manufacture proposes a console which has valid trademark registration certificate issued by Government of India. 5) Table top: - The material of the working surface shall be minimum 25 mm thick MDF with High Pressure certified scratch-resistant Laminate. The proposed console's life cycle shall be assessed (from approved LCA consultant) for environmental impacts associated with all the stages of a product's life for cradle to grave analysis. 6) Audit certified design feature of modular PU Edge. High density poly-urethane foam moulded on industrial grade aluminium core to form 50mm deep tapered edge to be installed on worktop. The edge shall be mechanically replaceable within 30 minutes, in case of damage or wear without opening or removing the worktop. Extruded PU edging/PVC T-beading shall be deemed unacceptable.

7) Slat Wall: - Slat Wall shall be made of approx. 2mm thick Extruded Aluminium (HE9WP aluminium alloy). The proposed console shall be UL Listed. 8) Monitor Arm: - The control desk shall feature ergonomic display mounting arms. It shall enable quick & easy replacement of VESA mounts & arm extensions as per the ergonomic requirement defined in ISO 11064. UL audit certified design feature of monitor arm assembly shall have auto lock, push & remove feature for quick release of VESA mounts and modular arm extensions for ease in maintenance and fixing of monitor by one technician within 30 seconds without using any tools. 9) Shutters & Side Legs: - Front, back shutters shall be of 18mm Laminated MDF Board with premium finish. Side leg shall be of 25mm of the same finish. Proposed console shall comply with the BIFMA X7.1 standard. The consoles (open plan) shall not emit TVOC(A), Formaldehyde i.e. 152 μg/m²*hr, 6.2 μg/m²*hr respectively. This is to ensure healthier air quality for the operators. Therefore, the proposed console shall be Greenguard Gold certified. 10) Structure:- Made of heavy duty extruded vertical and horizontal Aluminium profiles of 6005 grade. The Extrusions shall be duly powder coated with 40+ microns over all surfaces. All sheet metal parts shall be finished with a durable, black, electrostatic powder coating. To allow future extension and expansion, a weld free system shall be proposed. Interconnecting joints shall not be visible. The structure shall be rigid enough to withstand BIFMA X5.5: 2014 test. The control desk manufacture shall have had BIFMA X5.5:2014 certificate. The structure shall allow easy assembly of hinged shutters, slat wall, gland plate, monitor arms in extremely rigid manner.

SITC of counter for Gate House and Security Block 1) The furniture work surface shall be straight in shape to maintain grand aesthetic appeal. It shall be made of minimum 25mm thick prelaminated particle board with 2mm thick PVC edge banding tape. 2) The structure shall be made up of prelaminated particle board finish. 3) It shall have provision of Electrical and Lan sockets with concealed wiring. 4) Design as per Engineer In charge Approval. Approximate minimum dimensions – 1500mm(W) X 750mm(D) X 750mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of dining counter with 8 chairs 1) The dining counter top shall have 25mm thick Prelaminated Particle board with 2mm thick PVC edge banding tape. 2) The structure shall be made up of powder coated steel. 3) Chairs Without Arm, SS Pipe Frame Chrome Finish, Leatherite Tapestry 4) Approximate minimum dimensions – 2400mm(W) X 800mm(D) X 750mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Student Desk The minimum dimensions of tabletop will be 2100mm (W) x 450mm (D) x 770mm (H) (for tabletop). The seating bench shall be minimum 2100mm (W) X 400mm (D) X 450 mm (H). The desk shall be manufactured as per the specifications mentioned below: - 1. Side frame structure: Made of CRCA press-fit section 165.0 mm x 25.0 mm x 1.0 mm thickness bolted to 25.0 mm x 50.0 mm x 1.2mm thickness tube by using C-clamps made up of 3.0 mm thick sheet. The bottom tube shall have sufficient length to give support to the frame structure & shall have grouting provisions. 2. Seat and back rest frame structure: Made of CRCA press-fit section 165.0 mm x 25.0 mm x 1.0 mm thickness welded to MS pipe of 25.4 mm diameter x 1.2mm thickness. All 8 numbers of horizontal supports shall be made up MS tube having dimensions 25.0 mm x 25.0 mm x 1.2 mm thickness. MS tube of size 20.0 mm x 20.0 mm x 1.0 mm thickness and 100.0 mm long shall be welded to the frame to hold the horizontal supports. 3. Rectangular MS tube of dimension 50.0 mm x 25.0 mm x 1.2 mm thickness shall be closed with PPCP cap at both the ends. Pipe diameter 25.4 mm x 1.2 mm thickness shall be closed with PPCP cap at back side and under the seat. 4. Upper modesty panel and shelf shall be made of 0.8 mm thick CRCA sheet. The dimensions for upper modesty panel shall be H 175.0 mm x W 2000.0 mm x D 23.0 mm. The dimensions of shelf shall be W 2000.0 mm X D 300.0 mm X H 23.0 mm. The shelf shall have vertical partition at the center. This partition shall be made up of square MS tube having size 25.0 mm x 25.0 mm x 1.2 mm thickness. Stiffeners of MS tube having sizes as 20.0 mm x 20.0 mm x 1.0 mm thickness shall be provided in upper modesty panel and shelf. Front fascia of upper modesty panel of desk shall have embossed design. The corners of shelf (towards the seating bench) shall be rounded to avoid injury in case of accidental impact. 5. Additional lower modesty panel having size H 150.0 mm x W 2000.0 mm X D 23.0 mm shall be made up of 0.8 mm thick CRCA sheet with designer square perforations. MS tube of size 20.0 mm x 20.0 mm x 1.2 mm thickness shall be fixed across the length at the bottom side of lower modesty panel. 6. Seat and back rest shall be made of 18mm thick Particle board with laminated finish (one side shall be laminated, and other side shall have balancer finish). Technical details of seat and back rest are mentioned below: 6.1. Seating bench dimensions shall be W 2100.0 mm X D 400.0 mm: Front side shall have T beading. Remaining three edges shall be sealed with 2mm thick PVC edge banding tape. 6.2. Back rest dimensions shall be W 2100.0 mm x D 250.0 mm: Upper side shall have T beading. Remaining three edges shall be sealed with 2mm thick PVC edge banding tape. PVC Edge Banding make: Rehau.

7. Table top shall be made up of 18.0 mm thick particle board with laminate finish. Tabletop dimensions shall be W 2100.0 mm x D 450.0 mm. 8. Bag/bottle hooks shall be made of MS wire having diameter of 5.0 mm. The overall size of hook shall be W 23.0 mm, D 32.0 mm and H 80.0 mm. It shall be welded on inner facia of both the vertical press-fitted steel sections. 9. The MIG / Spot welding shall be done as per technical requirement. 10. All metal components shall be powder coated in satin finish with pretreatment process. 11. Four levelers of 12.0 mm shall be provided at bottom of desk to take care of uneven floor surface. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Student Desk The minimum dimensions of tabletop will be 3500mm (W) x 450mm (D) x 770mm (H) (for tabletop). The seating bench shall be minimum 3500mm (W) X 400mm (D) X 450 mm (H). The desk shall be manufactured as per the specifications mentioned below: - 1. Side frame structure: Made of CRCA press-fit section 165.0 mm x 25.0 mm x 1.0 mm thickness bolted to 25.0 mm x 50.0 mm x 1.2mm thickness tube by using C-clamps made up of 3.0 mm thick sheet. The bottom tube shall have sufficient length to give support to the frame structure & shall have grouting provisions. 2. Seat and back rest frame structure: Made of CRCA press-fit section 165.0 mm x 25.0 mm x 1.0 mm thickness welded to MS pipe of 25.4 mm diameter x 1.2mm thickness. All 8 numbers of horizontal supports shall be made up MS tube having dimensions 25.0 mm x 25.0 mm x 1.2 mm thickness. MS tube of size 20.0 mm x 20.0 mm x 1.0 mm thickness and 100.0 mm long shall be welded to the frame to hold the horizontal supports. 3. Rectangular MS tube of dimension 50.0 mm x 25.0 mm x 1.2 mm thickness shall be closed with PPCP cap at both the ends. Pipe diameter 25.4 mm x 1.2 mm thickness shall be closed with PPCP cap at back side and under the seat. 4. Upper modesty panel and shelf shall be made of 0.8 mm thick CRCA sheet. The dimensions for upper modesty panel shall be H 175.0 mm x W 3400.0 mm x D 23.0 mm. The dimensions of shelf shall be W 3400.0 mm X D 300.0 mm X H 23.0 mm. The shelf shall have vertical partition at the center. This partition shall be made up of square MS tube having size 25.0 mm x 25.0 mm x 1.2 mm thickness. Stiffeners of MS tube having sizes as 20.0 mm x 20.0 mm x 1.0 mm thickness shall be provided in upper modesty panel and shelf. Front fascia of upper modesty panel of desk shall have embossed design. The corners of shelf (towards the seating bench) shall be rounded to avoid injury in case of accidental impact. 5. Additional lower modesty panel having size H 150.0 mm x W 3400.0 mm X D 23.0 mm shall be made up of 0.8 mm thick CRCA sheet with designer square perforations. MS tube of size 20.0 mm x 20.0 mm x 1.2 mm thickness shall be fixed across the length at the bottom side of lower modesty panel. 6. Seat and back rest shall be made of 18mm thick Particle board with laminated finish (one side shall be laminated, and other side shall have balancer finish). Technical details of seat and back rest are mentioned below: 6.1. Seating bench dimensions shall be W 3500.0 mm X D 400.0 mm: Front side shall have T beading. Remaining three edges shall be sealed with 2mm thick PVC edge banding tape. 6.2. Back rest dimensions shall be W 2100.0 mm x D 250.0 mm: Upper side shall have T beading. Remaining three edges shall be sealed with 2mm thick PVC edge banding tape. PVC Edge Banding make: Rehau.

SITC of Flip desk table 1) The furniture top shall be made up of minimum 25mm thick particle board with 2mm thick PVC edge banding tape. 2) The under structure and complete structure shall be made up of sheet metal. 3) Flip table approximate Dimensions: 1200mm(W) X 600mm(D) X 750mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Computer desk table 1) The furniture top shall be made up of minimum 25mm thick particle board with 2mm thick PVC edge banding tape. 2) The under structure and complete structure shall be made up of sheet metal. 3) Computer table approximate Dimensions: 900mm(W) X 600mm(D) X 750mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Chair for flip/computer desk table Chair, PP Arm, Net Back Seat Fabric Tapestry, 4 Leg With Castor Powder Coated. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Guest House furniture 1. Study counter - 1 No. 2. Bed - 1 No. 3. Chair - 1 No. 4. Wardrobe - 1 No. Detailed specifications and mode of execution is mentioned in technical Specification of RFP. Study counter 1)The study counter consist of table & drawer. 2) The furniture top shall be made up of 25mm thick prelaminated particle board with 2mm thick PVC edge banding tape. 3) The furniture understructure shall be made up of 18mm thick prelaminated particle board with 2mm thick PVC edge banding tape. 4) Approximate Dimensions: 1200mm(W) X 600mm(D) X 750mm(H) Single Bed 1) The bed shall be made up of 18mm thick board laminated finish. Study Chair Chair, powder coated Pipe Frame, fabric tapestry. Full height Wardrobe 1) The top and shutter shall be made up of 18mm thick prelaminated particle board with 2mm thick PVC edge banding tape. 2) Approximate Dimensions: 900mm(W) X 600mm(D) X 2100mm(H)

SITC of hostel furniture 1. Study counter - 1 No. 2. Bed - 1 No. 3. Chair - 1 No. 4. Wardrobe shutter - 1 No. Detailed specifications and mode of execution is mentioned in technical Specification of RFP. Study counter 1)The study counter consist of table & drawer. 2) The furniture top shall be made up of 25mm thick prelaminated particle board with 2mm thick PVC edge banding tape. 3) The furniture understructure shall be made up of 18mm thick prelaminated particle board with 2mm thick PVC edge banding tape. 4) Approximate Dimensions: 1200mm(W) X 600mm(D) X 750mm(H) Hostel Bed 1) The bed understructure shall be made up of powder coated CRCA pipes and the outer cladding shall be made up of 18mm MDF. The bed shall have at least four-feet-wide storage space. Sharp corners to be avoided and the headrest shall have molded poly urethane edging on the top edge. The bed shall have provisions to keep shoes. The shoe rack shall be epoxy powder coated. Hostel - chair Chair, Chrome Plated Pipe Frame, Leatherite tapestry. 97.4 Shutter for Full height Masonry Almirah 1) The shutter shall be made up of 18mm thick prelaminated MDF board with 2mm thick PVC edge banding tape. 2) Approximate Dimensions: 900mm(W) X 2000mm(H)

Supply & installation of Manual Roller blinds having Aluminum Roller tube along with fabric pasted on it with glue having control unit for manual operations and bottom bar Aluminum powder coated for weight purpose, including fabric, fitting & accessories of approved make & colour etc. complete.

Providing and fixing of curtain rod & curtain cloth for door and windows made out of fabric of any colour and design as per the direction of Engineer-in charge with necessary acessories to fix the curtain etc.

Providing and fixing Metal perforated false ceiling at all heights including providing and fixing of frame work made of special sections power pressed from M.S. sheet and galvanised in accordance with zinc coating of grade 350 as per IS : 277 and consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling with dash fastener 12.5mm diax40mm long with 6mm dia bolts to the angle hangers of 25x25x0.55mm of required length, and other end of angle hanger being fixed with nut and bolts to G.I. channels 45x15x0.9mm running at the rate of 1200mm centre to centre to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre shall be fixed in a direction perpendicular to G.I. channel with connecting clips made out of 2.64mm diax230mm long G.I. wire at every junction including fixing of metal panels with ceiling section and perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre to centre with 25mm long drive-all screws @ 230mm interval and also including the cost of making openings for light fittings, grills, diffusers, cutouts and trap doors made with frame of perimeter channels suitably fixed all complete as per drawing and specification and direction of the Engineer in Charge (with trap door)

Providing & fixing calcium silicate ceiling tiles of size 595 x 595 mm in true horizontal level suspended on inter locking metal grid of hot dipped galvanised steel sections ( galvanized @ 170 gsm/sqm.) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38mm made from 0.30mm thick (minimum) sheet spaced at 1200mm center to center and cross “T” of size 24x25mm made of 0.30mm thick (minimum) sheet, 1200mm long spaced between main “T” at 600mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600mm and size 24x25mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 21x21x0.30 mm and laying false ceiling tiles of approved texture in the grid including, wherever, required, cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats fixed to ceiling with 6 mm dia and 50mm long dash fasteners, 4mm GI adjustable rods with galvanised level clips spaced at 1200mm center to center along main T, bottom exposed width of 24mm of all T-sections shall be pre-painted with polyester paint, all complete at all heights as per specifications drawings and as directed by Engineer-in-Charge of thickness of tiles as mentioned below. 8mm thick (with trap door)

Providing and fixing calcium silicate board false ceiling at all heights including providing and fixing of frame work made of special sections. 8mm thick (with trap door)

Supply, fixing, testing, commissioning of the followings equipments as mentioned below including all hardwares/ accessories as required for complete the installation in all respects as directed by the Engineer-in-charge

a. Treadmill

b. CROSS TRIANER

c. RECUMBENT BIKE

d. UPRIGHT BIKE

e. 3 STATION MULTIGYM

f. FLAT BENCH

g.DUMBELL RACK ‐ 1nO.

h. OLYMPIC RODS ‐ 5Nos.

i. DUMBELLS ‐ 155Kgs.

j. PLATES ‐ 105 Kgs.

k. AEROBIC STEP

l. ANKLE WEIGHT ‐ 1 Kg.

Description of Work / Item(s)

Amount

SITE PREPARATION

Clearing Grass and Removal of Rubbish (Maximum 150mm) by manual means and disposal at a lead of 5 k metres as per MoRT&H specification clause 201

Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to a lead of 500 metres from road boundary including removal and disposal of top organic soil not exceeding 150 mm in thickness as directed by Engineer in charge.In area of thorny jungle

Diluting and injection Chloropyrifos Emulsifiable concentrate 20% with 1% concentration for PRE-CONSTRUCTIONAL Anti termite treatment as per IS 6313 part III as amended from time to time and creating a continuous chemical barrier under and around the column pits, wall trenches, basement excavation, top surface of plinth filling, junction of wall and floor along the external perimeter of building expansion joints, over the top surface of consolidated earth of which approach is to be laid surrounding of pipes and conduits etc. complete as per specification (Plinth floor area only shall be measured for payment and excluding the cost of chemical emulsion).

CIVIL WORK

Earth work in excavation for roadway, including trimming bottom and side slopes in accordance with requirement of line, grades and cross sections, including disposal of surplus material with all lift and lead upto 10K metre as per MoRT&H specification clause 301.For soil/soft soil

Providing and laying in position cement concrete of specified grade Including the cost of centring and shuttering - All work upto plinth level :1:4:8 (1 Cement : 4 fine/ coarse sand : 8 graded stone aggregate 40 mm nominal size).

Providing and laying lean cement concrete 1:4:8 in Sub- base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonnes vibratory roller, finishing and curing complete as per clause 601, 112 of MoRT&H specification including all material, labour, machinery, lighting, guarding and maintenance of diversion.

Providing and laying in position pavement quality concrete including curing, compaction etc. complete in specified grade Including the cost of centering and shuttering - All work up to plinth level. 1:1.5:3 (1 cement : 1.3 coarse sand : 2.6 graded stone aggregate 40 mm nominal size).

Random rubble dry stone Kharanja (soling) under floor.

Brick masonry work in cement mortar with mechanical mixer with First class bricks (min. 10.5 Mpa) in foundation (at any level) complete as per drawing and technical specification and as per clause 1000 & 1300 of MoRT&H specification including all scaffolding material, labour, machinery but excluding pointing and plastering.In cement mortar 1:4 (1 cement : 4 coarse sand)

Random rubble stone masonry work in cement mortar with mechanical mixer in foundation (at any level) complete as per drawing and technical specification and as per clause 1000 and 1400 of MoRT&H specification including all scaffolding material, labour, machinery but excluding pointing and plastering.In cement mortar 1:4 (1 cement : 4 coarse sand)

Providing and fixing precast cement concrete M-20 grade (Using mechanical concrete Mixer) kerb stone top and bottom width 115 and 165 mm respectively, 250 mm high on 150 mm thick PCC M-10 grade foundation as per design, ncluding fixing at site as per clause 408 of MoRT&H Specification including all material, labour, machinery, lighting, guarding and maintenance of diversion.

Construction brick masonary catch basin with 75 class designation bricks in cement mortar 1:5 (1 cement:5 coarse sand), 200mm thick foundation concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size) inside & outside plaster in cement mortar 1:3 (1 cement : 3 coarse sand). inside finished with floating coat of neat cement, making haunches & channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) neatly finished, complete as per standard design including excavation, refilling & disposal of surplus earth.Size 600x600x600mm inside with 40mm precast Ferro-cement frame and perforated drain cover.

FINISHING

Providing & fixing 20mm thk, machine cut, Leather finish dark grey Granite fixed with 25mm average cement mortar of 1:3 (1 cement: 3 coarse sand) including base preparation, grouting and cleaning of joints. Cost to include pattern making and all lead and lift of material.

Providing & fixing 20mm thk, machine cut, Leather finish light grey Granite fixed with 25mm average cement mortar of 1:3 (1 cement: 3 coarse sand) including base preparation, grouting and cleaning of joints. Cost to include pattern making all lead and lift of material.

Flooring with Cobble stone of approx. Size 125x125x75 mm (thick) laid on 25 mm average thick cement mortar 1:3 ( 1 cement : 3 Coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the stone, laid in approved pattern complete in all respect as per direction of Engineer-in-charge.

Providing & fixing 20mm thk, machine cut, Sawn finish Beige colour sandstone fixed with 25mm average cement mortar of 1:3 (1 cement: 3 coarse sand) including base preparation, grouting and cleaning of joints. Cost to include pattern making and all lead and lift of material.

Providing and fixing of 60mm thick GREY coloured precast cement concrete interlocking paver block casted with rubber moulds in approved reflective colour and design having minimun compressive strength of 300 kg/ sq cm. The CC paving blocks be laid on average 50mm thick bed of coarse sand and the joint is to be filled with fine sand. Laying procedure on compacted sub-base as defined. Complete job is to be executed as per the instruction of Engineer incharge. The rates to be inclusive of all lead & Lifts etc. complete as per specifications.

Providing and laying 15mm thk EPDM flooring, of approved make and colour to be laid over the hard concrete surface with means of suitable/recommended adhesive.

Providing and fixing of 60mm thick RED coloured precast cement concrete interlocking paver block casted with rubber moulds in approved reflective colour and design having minimun compressive strength of 300 kg/ sq cm. The CC paving blocks be laid on average 50mm thick bed of coarse sand and the joint is to be filled with fine sand. Laying procedure on compacted sub-base as defined. Complete job is to be executed as per the instruction of Engineer incharge. The rates to be inclusive of all lead & Lifts etc. complete as per specifications.

Providing & laying 5mm thk machine made stamped concrete of river rock pattern providing RMC (Ready Mix Concrete) / Site mixing concrete plain of M30 grade 75mm (3inches) including, curing at the time of stamping at site . as/approved colour excluding the cost of foam work/shuttering.

HORTICULTURE AND PLANT MATERIAL

Trenching in specified soil upto a depth of 60 cm. including removal and stacking of serviceable materials and then disposal by spreading and neatly leveling within a lead of 500 metres and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or/and farm-yard manure before and after flooding with water (excluding cost of imported earth and sludge or farm-yard manure).

Digging holes in all kinds of soil and refilling the same with the excavated earth mixed with well decayed farm yard manure (cost of well decayed farm yard manure to be paid separately).

Holes .90 cm dia, and .90 cm deep

Holes 0.60 m dia and .60 m deep

Holes 0.45 m dia and 0.45 m deep

Supplying and stacking of good earth at site including royalty and carriage upto 5 km complete (earth measured in stacks will be reduced by 20% for payment)

Supplying and stacking at site dump manure from approved source, including carriage upto 5 km complete (manure measured in stacks will be reduced by 8% for payment) : Screened through sieve of I.S. designation 4.75 mm

Filling mixture of earth and sludge or manure in the desired proportion in trenches, flooding with water and leveling (cost of supplying earth and sludge or manure and mixing excluded).

SPRINKLER , DRIP & HYDRANT IRRIGATION SYSTEM

Piping Network - PVC Providing fixing , installation and testing with trenching and Back filling mainline 600 mm and Submain 450 mm in depth of PVC pipes (IS:4985- 88), and fittings & Accessories like tees, elbows, bends, junctions, Reducers etc of 10kg/cm2 pressure; as required/directed at site ,

PVC Pipe 90 mm x 6 kg/cm2

PVC Pipe 75 mm x 6Kg/cm2

PVC Pipe 63 mm X 6kg/cm2

PVC Pipe 50 mm X 6kg/cm2

PVC Pipe 40 mm X 6kg/cm2

SITC of Drip & Accessories

Providing and Fixing of Landscape Brown Color for recylced water application - 16 mm - 4 Bar Pressure Rating, 1.2mm Thickness, LEED Compliant, PE pipe -together with all required accessories. Make : Netafim / Rain Bird / Metzer

Providing and fixing of Dripline- 16mm 45 CM 3.5 LPH, 4 Bar Pressure Rating, 1.2mm Thickness together with all required accessories. Make: Netafim, Rain Bird, Metzer (Brown Color)

Providing and fixing of Pressure Comp. Bug Dripper 8 LPH Make : Netafim / Toro / Rain Bird

Providing and Fixing of Take Off Connection (Clamp Saddle or Tee + Riser + Threaded Adaptor+ Pipe Sch 1/2")with All fittings & Accessories

G.I. Lateral stake

SITC of Pop Up Sprinkler & Accessories

Providing of Spray Pop-up Sprinkler 4" (4" Pop Up hight from Bottom to Centre of Discharging Nozzle) from (2.4 to 5.4 Mtr Radius) with Check Valve, complete with required nozzle Make : Rain Bird/ Toro/ Nelson

Providing of Swing Joint 1/2" with PP Clamp Saddle Chromed Nut Bolt & Nitrile Rubber Gasket Make: RainBird/Toro/Astore

SITC of Various Valves with required Fittings & Tapping PP Clamp Saddles with Chromed Nut Bolt & Nitrile Rubber Ring

PVC Ball Valve 63mm PN 16 Make: GF / FIP / ASTORE

Butterfly Valve 75 mm (for Main line Isolation) Make: Astore, Italy/ FIP/ GF+

3/4" Quick Couppling Valve

3/4" Quick Couppling Valve Key

PP Saddlet Tee 75 X 3/4" with ASTM Pipe (18" Long)

Saddle 75 MM X 1''

1" Double Acting Air cum Vacum Release Valve Make: Bermad/ARI/Plasson with GM valve 1" Make: NIBCO/Zoloto

PVC Flush Valve 40 mm

Rectangular Valve Box 12" Make: Carson Brooks/Rain Bird

Round Valve Box 10" Make: Carson Brooks/Rain Bird

Round Valve Box 6" Make: Carson Brooks/Rain Bird

SITC of Disc Filter, 80/110 Micron with all required Accesories

Providing and Fixing of Manual Cleaning Screen Filter capacity of 50 m3/h 3"

Providing and Fixing of G.I. Header with 3 Butterfly Valve

Providing and Fixing of Road Sleeve of various sizes

Trenching & Back Filling with Installation Charges of 450mm x600m with compacting of soil base

PLANT MATERIAL

Supplying and planting following TREES

AFRICAN TULIP TREE,12' ht

BRAZILIAN CASSIA,12' ht

TECOMA ARGENTEA,12' ht

WEEPING FIG,10' ht

NEEM,12' ht

SPANISH CHERRY,12' ht

SHEESHAM,12' ht

PILKHAN,12' ht

GULMOHAR,10' ht

KADAM,12' ht

AMALTAS,10' ht

KACHNAR,10' ht

PLUMERIA ALBA,10' ht

Supplying and planting following PALMS

FOXTAIL PALM,4'ht

BOTTLE PALM,4'ht

RAPHIS PALM,4'ht

DATE PALM,4'ht

ARECA PALM,4'ht

Supplying and planting followingSHRUBS AND GROUND COVERS

IPOMEA CREEPERS,4'ht

BIG NONIA VENUSTA,4'ht

BOUGAINVILLEA,4'ht

WHITE KANER,3'ht

GOLDEN DURANTA,1'6" ht

FIREBUSH,3'ht

ENERMI ,1'6" ht

MOGRA,2'ht

VARIEGATED DURANTA,1'6" ht

SPIDER LILIES,1'6" ht

TECOMA GAUDI CHAUDI (T.G.C.),1'6" ht

TABERNAEMONTANA C. (T.M.C.),1'6" ht

ACALYPHA RED,1'6" ht

RAAT KI RANI,1'6" ht

ASPARAGUS (G.C.),1'6" ht

IXORA,2' ht

SITC OF LANDSCAPE LIGHTING

Supplying and fixing Decorative Taurus Bollard height 800mm having 140mm dia and pipe dia is 76mm, Decorative casting part are PU painted, Bollard having PC diffuser along with 10W led lamps and bollard as per sketch enclosed in specifications and of preferred makes

Supplying and fixing Ultra compact 8 W led spike light.Corrosion proof, die cast aluminium composite construction alloy grade 6061. 100-300V Voltage range of operation, with high CRI of >80 and IP66 protection.Unique designed with zero water accumulation provision to ensure high life.adjustable head.LED lifespan 50000 burning hrs.Inbuilt overvoltage and short circuit protection included.Dimension (mm) Head Dia | length | height- 49| 110 | 255 along with lamps and fixture as per sketch enclosed in specifications

Supplying and fixing Corrosion resistive 9W LED Burial/inground light with aluminium die cast housing grade 6061 and stainless steel cover.IP67 protection and beam angle less than 15 degrees to avoid spillover.PF>0.98 and Athd<10%.surge protection >4KV.Inbuilt over voltage and shortcircuit protection included.LED lifespan 50000 burning hrs. Dimension in (mm) along with 9 W led lamps and fixture as per sketch enclosed in speccifications Diameter | height - 83.8 | 129.4.and of preferred makes

Supplying and fixing 2x7 W Up & Down Wall light with weather proof extruded aluminium housing grade 6063 and class II electrical protection.IP65.Operating voltage range of 120-300V. Inbuilt surge protection 4KV.Phase to phase,over voltage and short circuit protection.CRI>80.Available Beam angles of 15,36,50 degrees. LED lifespan 50000 buring hrs. Dimension in mm ø | l | h -80 | 115 | 200 / ø | l | h - 80 | 120 | 192 along with lamps and fixture as per sketch enclosed in specifications and of preferred makes.

Supplying and fixing of Decorative post top Light Housing:Fitting made with Corrosion resistant die cast aluminum. Rubber gaskets are provided at appropriate location for dust and water protection. Aluminum hat used for reflection of light downwards. Optical: Diffuser is made In unbreakable PC material. Highly efficient optical system in Vertical lamp. Direct lighting system designed for energy saving lamps. The optical system has been carefully engineered to provide high illumination and enhanced security. Electrical: Fitting is wired for integrated 40 watt LED.along with lamps and fixture as per sketch enclosed in specifications and of preferred makes. Finishing:Complete fitting is pure polyester based powder coated with high corrosion resistance and chemical chromatised protection. Also available with multiple coats of weather resistant Polyurethane paint in various colors. along with lamps and fixture as per sketch enclosed in specifications and of preferred makes

Supplying and fixing of Decorative Flox pole total height of the pole is 3mtr, Lower part of the pole having 114mm dia , and 1 mtr height. Upper part of the pole having 76mm dia and height is 2 mtr. Decorative casting part are PU panted in three layers coating in which 1st layer with ETCH primer, 2nd layer with EPOXY primer and 3rd final layer with PU Paint, square base plate having 250*250*10, Oval shape service window at lower part of pole having loop in loop. out 4 way connector 40 amp suitable for 10Sq mm wire with 6 amp single pole MCB.

supplying and fixing 11 W/ Meter with 120 LED / Meter LED Flex Long, efficient service life 10,000 hours (L70/B50) — Various colour temperature options for different applications (3000K / 4000K / 6500K) Simple and reliable,<0.5s start-up time Best-in-class colour consistency: SDCM s5 High colour consistency CRI>80 Protection Class IP65 Maximum length 45M

Supplying and fixing smart POLE should be made of heavy duty extruded alumunium profile of 6mtr ht with 70watt LED(Make of light :wipro/philips/pyrotech electronics) street light with wifi n other connectivity.

WATER FOUNTAINS

Earth work in excavation for roadway, including trimming bottom and side slopes in accordance with requirement of line, grades and cross sections, including disposal of surplus material with all lift and lead upto 1000 metre as per MoRT&H specification clause 301.In ordinary Rocks

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level :1:4:8 (1 Cement : 4 fine/ coarse sand : 8 graded stone aggregate 40 mm nominal size).

Random rubble dry stone Kharanja

Providing and laying structural plain/ reinforced cement concrete (design mix) of specified grade in substructure at all levels using concrete mixer and vibrator, including cost of form work, as per drawing and technical specifications complete as per clause 1500, 1700 and 2200 of MoRT&H specification including all material, labour, scaffolding etc.RCC Grade M -20

Centring and shuttering with plywood or steel sheet upto two stories or height upto 7.5 metre above plinth level including strutting, propping etc. and removal of form for :Foundations, footings, bases of columns, etc. for mass concrete.

Centring and shuttering with plywood or steel sheet upto two stories or height upto 7.5 metre above plinth level including strutting, propping etc. and removal of form for Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

Reinforcement for R.C.C. work at all levels including straightening, cutting, bending, placing in position and binding all complete. @90kg/cum of Thermo-Mechanically Treated bars.RCC

Water Fountains

Supplying and fixing of Water Fountain type I:The type 1 water fountain will consists of 25 no of Foam Nozzle, 25 number of angular valve with all necessary connection pipes, one electrical panel for 2 pumps. The work will also include the SITC of one number of Submersible Mono block Pump 10 HP,one number of Submersible Mono block Pump 5 HP, 2 number of micro processing control, 30 nos of LED Based Colour Changing Light,VFD Panel for pumps with PLC For Musical Fountain,pressure switch,relay card,solident valve with all programming and design of water faountain body. All electrical items should be of specified ratings . The sizes and types of electrical items should be of same specs and makes as specified in electrical BOQ . The panle and items , their specifications , makes Quality etc is to be get approved from Engineer in Charge .

Supplying and fixing of Water Fountain type II:The type II water fountain will consists of 12 no of Foam Nozzle, 12 number of angular valve with all necessary connection pipes, one electrical panel for 1pump. The work will also include the SITC of two number of Submersible Mono block Pump 5 HP, 1 number of micro processing control, 12 nos of LED Based Colour Changing Light with all necessary wiring work for the same.

Supplying and fixing of Water Fountain type III:The type III water fountain will consists of 3 no of Jet Nozzle, 3 no of mushroom nozzle,6 number of angular valve with all necessary connection pipes, one electrical panel for 1pump. The work will also include the SITC of one number of Submersible Mono block Pump 5 HP, 1 number of micro processing control, 3 nos of LED Based Colour Changing Light with all necessary wiring of specified load and cables used for such applications work for the same.

Finishing

Providing & fixing 20mm thk, machine cut, Flamed finish Black coloured Granite fixed with 25mm average cement mortar of 1:3 (1 cement: 3 coarse sand) including base preparation, grouting and cleaning of joints. Cost to include pattern making and all lead and lift of material.

Providing & fixing 20mm thick, machine cut, Flamed finish Grey coloured Granite fixed with 25mm average cement mortar of 1:3 (1 cement: 3 coarse sand) including base preparation, grouting and cleaning of joints. Cost to include pattern making and all lead and lift of material.

Providing & fixing 20mm thick, machine cut, polished mint sandstone fixed with 25mm average cement mortar of 1:3 (1 cement: 3 coarse sand) including base preparation, grouting and cleaning of joints. Cost to include pattern making and all lead and lift of material.

COMPOUND/TOW WALL

Earth work in excavation for compound/tow wall, including trimming bottom and side slopes in accordance with requirement of line, grades and cross sections, including disposal of surplus material with all lift and lead upto 1000 metre as per MoRT&H specification clause 301.In Ordinary Rocks

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level :1:4:8 (1 Cement : 4 fine/ coarse sand : 8 graded stone aggregate 40 mm nominal size).

Providing and laying structural plain/ reinforced cement concrete (design mix) of specified grade in substructure at all levels using concrete mixer and vibrater, including cost of form work, as per drawing and technical specifications complete as per clause 1500, 1700 and 2200 of MoRT&H specification including all material, labour, scaffolding etc.RCC Grade M -25

Random rubble stone masonry work in cement mortar with mechanical mixer in superstructure (at any level) complete as per drawing and technical specification and as per clause 1000 and 1400 of MoRT&H specification including all scaffolding material, labour, machinery but excluding pointing and plastering

Brick masonry work in cement mortar with mechanical mixer with First class bricks (min. 10.5 Mpa) in foundation (at any level) complete as per drawing and technical specification and as per clause 1000 & 1300 of MoRT&H specification including all scaffolding material, labour, machinery but excluding pointing and plastering.In cement mortar 1:4 (1 cement : 4 coarse sand)

Wrought iron and mild steel welded work) (using angles, square bars, tees and channel grills, grating frames, gates and tree guards of any size and design etc. including cost of screens and welding rods or bolts and nuts complete fixed in position

Finishing

Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade

Stone work ( machine cut edges) for wall lining upto 10 m height etc. (Veneer work) backing filled with a grout of 12mm thick cement mortar 1:3 (1 Cement : 3 coarse sand) and jointed with Cement mortar 1:2 (1 cement : 2 stone dust) including rubbing and polishing complete. (To be secured to the backing by means of cramps which shall be paid for separately)Kota / grey bijolia stone slabs exposed face dressed and rubbed.25 mm thick

SCULPTURE/OUT DOOR FURNITURE/PERGOLA ETC.

Supplying and fixing of Babel Drum (Large size) Steel tongue is drum of 470 mm diameter with 06 numbers laser cut tongues tuned to C-major pentatonic. The body should have drain hole in base body. The body should have drain hole In base body. Made of 316L mirror polished marine grade stainless steel having width of 510 mm and height of 820-1080 mm. The minimum of stainless steel should have 17 kg approximately. The work includes nuts & bolts for pole protection at platform in foundation cement concrete (1:2:4) block size of 0.45x0.45x0.50m

Providing and fixing of RED CEDAR( ip65 grade) of 40x100mmplanks on MS framed structure steel welded, in built up section framed work including cutting hoisting, fixing in position with connecting plates or angle cleats on concrete block of 600mm x600mm of 550 mm ht.

Providing and fixing of 18mm thick granite edge polished on cement concrete block including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering -

Providing and fixing of 25mm thick grey /brown bijolia or sandstone with edge polished on cement concrete block including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering -

Stone n boulders :providing and placement of 8-12 tonnees of weight of stone boulder of varied shape n size over compacted soil with 75 mm pcc as base

Stepping stones :Providing and laying of 600x600x75 mm grey Bijolia stone slab over ramped n compacted soil base

Supplying n placement of potted plants FRP POTS of Rou Compe S1, S2, S3 (CREDO or similar) including cocopit, manure, plants and complete in all respects

SAVE WATER SCULPTURE

Supply of Save water sculpture Made up of stainless steel, grade 316 . The sculpture should have 6m stainless steel 304 grade pole with water drope shape structure weld with pole. . The minimum weight of stainless steel should be 13 Kg. The work includes nuts and bolts (Hilti make) for pole protection at bottom platform in foundation of cement concrete (1:2:4) block of size 0.60*0.60*0.60m and as approved by Engineer-in-charge. The rates include cost of material, transportation, set-up, dismantling and site clearing. The site has to be cleaned after commissioning of instruments as per the direction of Engineerin-charge

Providing & Laying Rubber Flooring Rubber Flooring 36mm Thick (25mm Rubber Buffing + 6mm EPDM)PDM MIX Rubber Flooring of 36mm Thickness Over Well Layed Cement Concrete Surface at Site as per the Directions of Officer in Charge of the site using good Quality of Binder Or Adhesive

Providing and fixing CHESS TABLE WITH 4 STOOLS ,Square Chess Table (2.75ft * 2.75ft) made in RCC with art work (Chess Board finishing) on table top along with 4 stools for seating (1.25ft * 1.25ft each) made in RCC with artistic finishing on the outer surface and painting.

supplying and fixing WALL WITH ACUPRESSURE AND MURAL ART.Cleaning of the wall surface (76.5ft * 5.25ft), single coat rough plastering, making artful shapes by relief plastering and giving artistic finish to the wall surface by colouring it into themes of village, mountains, animals, forests etc. Also, artfuly embedding glass pebbles into the wall surface for acupressure and massage of the body parts.

Supply of Sculpture Of a Artistic Column group of 10' And 9' And 8' Height Statue with artistic [ S ] design work finish in artistic original color. Polyurethane foam filling in statue. Fabrication work in 2 inch square pipe With 3 mm thickness in all curved parts of statue for solid strength. Plastic and fiber coat finish at outer surface with 3 coats. Fire resistant coating at full statue. Base stand in ms. 1.5 feet square plate in 3mm thickness

Supply of Sculpture Of a Question & Answer of 8' dia. Statue with art work finish in artistic color Finish. Made by MS Sheet deer statue. Fabrication work with clear welded in all parts of statue (hand, leg, head) for solid strength. deco and rust resistant coat finish at outer surface with 3 coats. lacquar coating at full statue. Base stand in ms. 1.5 feet square plate in 3mm thickness. The sculpture will be supplied as per indicative pictures given in the tender document and direction of work in-charge

Supply of Sculpture Of a SWAN of 2.5 ' Height Statue with art work finish in artistic Silver colour. Polyurethane foam filling in statue. Fabrication work in 2 inch square pipe. 3 mm thickness in all parts of statue (tail, body , head) for solid strength. Plastic and fiber coat finish at outer surface with 3 coats. Fire resistant coating at full statue. Base stand in ms. 1.5 feet square plate in 3mm thickness. The sculpture will be supplied as per indicative pictures given in the tender document and direction of work in-charge.

Supply of Waste to ART Butterfly Chair made by metal spare part (waste material- gear, chain, ring) of a 5 ' Height Statue with art work finish in artistic tri mixx colour. Fabrication work in 2 inch square pipe. 3 mm thickness in all parts of body for solid strength. Base stand in ms. 1.5 feet square plate in 3mm thickness. The sculpture will be supplied as per indicative pictures given in the tender document and direction of work in-charge

Supply of Sculpture Of SCHOLAR of 7.5' height Statue with art work finish in artistic white colour. Fabrication work in 2 inch square pipe. 3 mm thickness in all parts of statue (tail, body , head) for solid strength. Polyurethane foam filling in staue Die Plastic and fiber coat finish at outer surface with 3 coats. Fire resistant coating at full statue. Base stand in ms. 1.5 feet square plate in 3mm thickness. The sculpture will be supplied as per indicative pictures given in the tender document and direction of work in-charge

Supply & installation of marine grade polysteel modular GAZEBO, square shape & elevation as per the attached design, of size 2.5mx2.5mx2.5m made of UV stabilized class-1 fire retardant polyster composite with glass fibre reinforcement of 750GSM, self coloured, textured surface finish with scratch resistant aliphatic grade UV stabilized polyurethane paint; Inner frame work made of mild steel hot dip galvanized; All hardwares are to be of stainless steel. To be \individually hand crafted to replicate steel and cast iron and to be installed with ground using foundation bolts.

Supply and Installation of Wrought iron and mild steel welded work ,using angles, square bars, tees and channel grills, grating frames, gates and tree guards of any size and design etc. including cost of screens and welding rods or bolts and nuts complete fixed in position but without the cost of excavation and concrete for fixing which will be paid separately. The details of Work to be executed will be as per direction and drawings given by the Architect / Engineer in Charge .

MS Tree guard Canopy as per detailed Drawings given by Architect Engineer in charge .

Pergolas; steel hollow sections; including posts; fixings and two coats of Red oxide and Enamel paint as per detailed Drawings given by Architect Engineer in charge .

SIGNAGE

Suplying and fixing ARTISTIC SIGNAGE (On sagar black stone of 1500mm x 2100mm , 200 mm thick with water jet cutting of 12 mm filled with corian). The matter to be written with fonnt andsize will be as per direction of Engineer in charge / Architect

TOTEM SIGNAGE: Design, composition, Supply and installation of structural steel frame made out of medium duty 50mm square pipe section, red oxide primer with two coat of synthetic enamel painting, providing and fixing 3/4mm thick polycarbonate sheet with 40% transluency, with graphics on single side digitally printed on UV cured 3M media or 3M external grade binly totens to be intenally illuminated with LED paower module double side, high output 7100k numbers as perdsign, 140 degree at the distance as recommended by architect/ Engineer in charge

EXTERNAL DIRECTIONAL SIGNAGE: Supply and installation of single sided non lit External Multi Directional Signage structural section, gusset plate 6mm thick and two base plates of size 400*400*10mm red oxide primer with two coat of synthetic enamel painting fixing of base plate to foundation through anchor bolt, providing and fixing ACP sheet 3mm in cladding, 3M vinyl of background with High Intensity Prismatic reflective sheet self adhesibe graphics with 3M scotchal and mounting with 3M approved tensioning system. Matter in specified size/ font to be written on Directional signages will be given by Engineeer in Charge .

NURSERY

Fabrication , installation and erectioning of nursery of 6mtr x12mtr x 8mtr ht in 75mm M.S round pipe with 600 to 900 mm distance between structural members , firmly fixed to gound , covered all 5 sides(includung n opening for entering) with 90 gsm green net and wire mesh to supprt the green net etc. the detailed structural design will be given by Engineer Incharge in consulting with PMC / Architect / Structural Designer

Making of underground water tank of 5'x8'of 7' depth with wall thickness of 9 " with FPS/ Stone masaonary duly plastered along with1.5 hp pump, Piping , cabling , starter complete in all respect . The underground water tank should be Finished with 5 layer water proofing on all five sides . The Design of underground Water tank along with covered Slab , Mnahole cover etc will be given by engineer in charge in consultant with PMC / Architect / Structural Designer

Fabrication and Installation of seed and fertilizer store room of size approx 10'x10'x10'. Structure to made out of portacabin and M.S members, including lockable PVC door of size approx 3'x7' and a window of approx 3'x3' complete in all means with light and ventilator fan.

Description of Work / Item(s)

Amount

ROOMS

AUDIO SYSTEM

Supply, Installation, Testing & Commissioning of 4.5-inch, 2-way, Full Range, Ceiling-mount loudspeaker. Frequency range - 70Hz-16kHz, Rated Power - 16Watts, Sensitivity-89 dB SPL, Coverage Angle (-6 dB)-140° (500 Hz to 5 kHz), Maximum SPL Continuous/Peak-101dB/107dB, Rated Impedance - 8 Ohms. Transformer Tapping - 70V/100V(16, 8, 4,2 watts).Material - Painted ABS polymer Baffle and Power coated steel grille. Safety rating - UL1480, UL2043. Mounting rails and C-Ring for ceiling tile included.

Supply, Installation, Testing & Commissioning of Quad channel class-D amplifier. Power - minimum 100 watts/channel @8Ω/4Ω or better. Should support 70V/100V.Should have Power sharing between channels or Bridge/Parallel mode to combine a pair of channel for maximum output . Signal to Noise ->100 dB or better, Frequency Response-20 Hz - 20 kHz or better, Input Impedance->10 kΩ (balanced & unbalanced) or better, Front Panel Indicators-Power, per channel Signal, Protect/Limit etc. Better to have Energy Star rating for power saving. Shall include rack and surface mounting brackets.

Supply, Installation, Testing & Commissioning of Dual channel class-D amplifier. Power - minimum 60 watts/channel @8Ω/4Ω or better. Should support 70V/100V.Should have Power sharing between channels or Bridge/Parallel mode to combine a pair of channel for maximum output . Signal to Noise ->100 dB or better, Frequency Response-20 Hz - 20 kHz or better, Input Impedance->10 kΩ (balanced & unbalanced) or better, Front Panel Indicators-Power, per channel Signal, Protect/Limit etc. Better to have Energy Star rating for power saving. Shall include rack and surface mounting brackets.

Supply, Installation, Testing & Commissioning of Digital Signal Processor with minimum 16 Mic/Line Inputs and 8 Line Outputs. AEC Channels - minimum 16 assignable & routable with minimum tail length of 200ms. GPIO Ports - Minimum 16 Inputs and 16 Outputs. Minimum 8x8 Dante channels and support for up to 128x128 Network audio channels via Dante or AES67. SIP Softphone integration for Audio conferencing and 16x16 USB Audio channels supporting AV USB Bridging for software or web based conferencing applications. The processor shall also have minimum 24 bit-A/D-D/A converters, 48 kHz Sample rate,Frequency response of 20 Hz to 20 kHz or better. 2xEthernet, RS232 & GPIO ports for Third party device control. Third Party control can be added as software license or Hardware (i.e., Crestron/Extron) to fulfill the requirement.

Supply, Installation, Testing & Commissioning of Digital Signal Processor with minimum 4 Mic/Line Inputs and 4 Line Outputs. AEC Channels - minimum 8 assignable & routable with minimum tail length of 200ms. GPIO Ports - Minimum 8 Inputs and 8 Outputs. Minimum 8x8 Dante channels and support for up to 64x64 Network audio channels via Dante or AES67. SIP Softphone integration for Audio conferencing and 8x8 USB Audio channels supporting AV USB Bridging for software or web based conferencing applications. The processor shall also have minimum 24 bit-A/D-D/A converters, 48 kHz Sample rate,Frequency response of 20 Hz to 20 kHz or better. 2xEthernet, 2xRS232 & GPIO ports for Third party device control. Third Party control can be added as software license or Hardware (i.e., Crestron/Extron) to fulfill the requirement.

Supply, Installation, Testing & Commissioning of Audio, Video & Control processor. Video: 3-HDMI Inputs and 2-HDMI Outputs with scaling and resolution up to 4K60 4:4:4. Content protection - HDCP 2.2 compliant, 8-channel PCM HDMI audio embedding/deembedding. Audio: 3.5 mm unbalanced stereo mic/line input and 3.5 mm unbalanced stereo line output. Dante/AES67 Network audio support for up to 32x32 channels. 8 configurable and routable AEC channels @200ms tail length. Control: RS232, GPIO ports for external device control. Dual Gigabit ethernet ports. Power-POE and AUX. Mounting accessories included.. Third Party control can be added as software license or Hardware (i.e., Crestron/Extron) to fulfill the requirement.

Supply, Installation, Testing & Commissioning of 8 Channel Networked I/O Expander.8 Analog Balanced I/O Individually Switchable as Mic/Line Input(w/ phantom power) or Line Output. Dual LAN Port for Redundancy with PoE capability on one LAN Port. Upto 8x8 channel of digital I/O via Audio-to-USB Bridging for direct PC connection via driverless USB connectivity. GPIO Inputs & Outputs & 3 Pin RS232 Connectivity for external device control. Front Panel Display showing System & Network Information. Front Panel ID button for device identification in software. Configuration & Monitoring via PC Software.

Supply, Installation, Testing & Commissoning of Wired Table Top boundary microphone. Pickup pattern - Cardioid/Half-Cardioid. Programmable microphone button for PTT, PTM, Toggle on/off, Permanent on and a two-color LED ring as a status indicator. Nominal Imprdance - 200Ω, Frequency Response - 40 Hz – 20 kHz, Max SPL-140 dB.

Supply, Installation, Tetsing & Commissoning of Network Dante/AES67 Beamforming Ceiling Tile Microphone array, Power over Ethernet, Audio Out - Dante/AES67, LAN - 2xRJ45, Max SPL - 104 dB or better, Configuration option for Priority and Blackout zones, support for Far and Local in-room audio.

Supply , Installation , Testing & Commissioning of Wireless Handheld Microphone set: having Dynamic cardioid or better polar pattern, 40 MHz or more switching Bandwidth, Should have Signal to noise ratio >108dBA or better, Total Harmonic Distortion should be <0.9%, Frequency Response: 80 to 18000Hz or better, RF Sensitivity: < 2.5 μV at 52 dB(A), Should have RF Power of 30mW or more, Should have mute/unmute button, Operating time: up to 8 hours or better

Supply, Installation, Testing & Commissioning of Wireless Lapel Microphone set: having pre polarised condenser microphone with omnidirectional or better polar pattern, 40 MHz or more switching Bandwidth, Should have Signal to noise ratio >108dBA or better, Total Harmonic Distortion should be <0.9%, Frequency Response: 50 to 18000Hz or better, RF Sensitivity: < 2.5 μV at 52 dB(A), Should have RF Power of 30mW or more, Should have mute/unmute button, Operating time: up to 8 hours or better.

Supply, Installation, Tetsing & Commissoning of cardioid condenser gooseneck microphone with Table stand base. Mute/Unmute button and status light ring. Gooseneck length min 40 cm, connector type - XLR, Impedance - <100Ω, Frequency response - 50Hz - 20kHz, Max SPL -130 dB SPL.

DISPLAY SYSTEM

Supply, Installation, Testing and Comissioning of 82" 4K UHD (3840 x 2160) LED display with min 300 nits brightess or better, Contrast ratio: 4000:1, Aspect ratio: 16:9, Viewing angle: 178° h/v, Response time: 8ms, Input ports:2xHDMI, 1 x USB, LAN / RS232 Control along with built-in 2 x 10W speakers with standard acessories.

Supply, Installation, Testing & Commissioning of suitable MS wall bracket for bracket for LED Display mounting with standard accessories.

Supply, Installation, Testing and Comissioning of 75" 4K Mainstream Proff Display for AVSI&Digital Signage Project with New symmetrical slim Design/ Intelligent UHD upsclalling/ Dynamic Crystal Color/ Narrow Bezel Design/ Slim and Flat back Design/ and Web Browsing facility/4000:1 Contrast Ratio/ Stereo Mini Jack/ HDMI / RS232 / USB / RJ45 /Wi-Fi built-in /Built-in-Speakers / EDGE LED/ Haze coating/ Tizen 4.0/ Samsung Workspace-Office 365/ PC Less Conf/ VM Ware Horizon/1.7GHz Quad-Core CPU/ 8GB Storage/ 8MS Response time/ EMC class B compliant/EPEAT Reg./ IP5X for Dust Proofing/ HDR+

Supply, Installation, Testing & Commissioning of suitable MS wall bracket for bracket for LED Display mounting with standard accessories.

Supply, Installation, Testing and Comissioning of Laser Projector with 5500 Lumens & Short Throw Lens Reproduce True-to-life Images for Totally Immersive ExperiencesHASSLE-FREE INSTALLATION - With V/ H lens shift, 2D keystone and corner fitAMAZING COLOR ACCURACY - 92% Rec 709 color accuracy to see every detail FAST <17ms response enables realistic simulation and gaming5500 ANSI LUMENS FOR Big screens - Will effortlessly fill large screens up to 20 feet wideMAINTENANCE FREE DESIGN - Sealed IP5X laser engine means no dirty projector filters and 20,000 hour laser

Supply, Installation, Testing & Commissioning of Tabtensioned Motorised Projection screen Aspect ratio 16:9 130 to 165 " Diagonal with mounting and standard accessories.

Supply, Installation, Testing and Comissioning of Projector Mount Heavyduty

VIDEO,SWITCHING & INTERFACE SYSTEM

Supply, Installation, Testing & Commissioning of 1G HDMI Video Encoder. Inputs- 3 HDMI capable of streaming of 3-HDMI sources simultaneously.Resolution-upto 4K60 4:4:4, Power - PoE and AUX PSU. Ports Connections - RS232, GPIO, Audio Inputs, Audio Output & USB port for HID Signal transfer. Content Protection: HDCP 2.2 compliant, EDID Managament. Dante/AES67 Audio Support.Mounting accessories includedIf Encoder is capable of streaming only one input, match the qty as per the requirement (6 Inputs).

Supply, Installation, Testing & Commissioning of 1G HDMI Video Decoder. Outputs- 2 HDMI capable of scaling and outputting 2 streams simultaneously.Resolution-upto 4K60 4:4:4, Power - PoE and AUX PSU. Ports Connections - RS232, GPIO, Audio Inputs, Audio Output & USB ports. Content Protection: HDCP 2.2 compliant, EDID Managament. Dante/AES67 Audio Support.Mounting accessories included. If Decoder is capable of decoding only one stream, match the qty as per the requirement(2 outputs).

Supply, Installation, Testing & Commissioning of Table Mount enclosure with 1xHDMI and 1xUSB with F-pigtail connectors and 2 x Universal Power sockets. Manually open and close lid with Black and Clear anodize color options.

Supply, Installation, Testing & Commissioning of Wireless Presentation System. Simultaneous display of up to four presentation sources in a quad window, Supports multiple user connections simultaneously, 1 HDMI or better output; 1 or better USB Port; 1 or better Analog Stereo Audio output port; 1920 X 1080 or better output resolution along with ethernet port. It should support Windows, Mac, iOS, and Android.

Supply, Installation, Testing and Comminssioning of HDBT Wall Plate Tx/Rx set with 1xHDMI, 1xDP/VGA, RJ45 Ports, complete with Transmitter, Receiver set.

CONTROL SYSTEM & ROOM SCHEDULING

Supply, Installation, Testing & Commissioning of 10" Wireless Touch panel with ratina display with required perpetual license and accessories and wall mount.

Supply, Installation, Testing & Commissioning of 10 port L2 Gigabit POE+ Network Swicth with Multicast support with IGMP V1/V2, QoS support, IPV4/IPV6 Support, Switching Capacity in Gigabits per Second, 1 Gbps Non-blocking ports with standard accessories.

CABLE, CONNECTORS, ACCESSORIES

Supply, Installation, Testing & Commissioning of 18Gbps 4K 30-feet HDMI Cable.

Supply, Installation, Testing & Commissioning of 18Gbps 4K 15-feet HDMI Cable.

Supply, Installation, Testing & Commissioning of 18Gbps 4K 9-feet HDMI Cable.

Supply, Installation, Testing & Commissioning of 18Gbps 4k 3-feet HDMI Cable.

Supply, Installation, Testing & Commissioning of 2 core 2.5 sqmm PVC Sheathed loudspeaker cable.

Supply, Installation, Testing & Commissioning of 2 core shielded balanced microphone cable.

Supply, Installation, Testing & Commissioning o23 W\ AWG Cat6 Cable for AV Network connectivity .

Supply, Installation, Testing & Commissioning of Shielded Cat6 Cable for Digital Conference System connectivity.

Supply, Installation, Testing & Commissioning of Patch Cable & Connectors

Lighting Controls

Supply, Installation, Testing & Commissioning of Processor - This device can be used to manage up to 50 simple and advanced scenarios. Using the scenario programmer, the system canperform certain actions not only following a command by the user but also as a result of external events.Power supply from BUS: 18-27 VdcMax. absorption: 30 mAOperating temperature: 5 – 40 °C RJ 45 for 10/100 Mbit Ethernet LAN

Supply, Installation, Testing & Commissioning of Bus Power supply - This device must be used to supply power to the Lighting Management Systems. On the output, the unit supplies a 27 Vdc continuous low voltage, with a maximum current of 1 A. It is electronically protected (without fuses) against short circuit and overload.

Supply, Installation, Testing & Commissioning of This device is used as a Protection for power supply IN (AC power supply input)Rated voltages: 230 V ±10%Nominal working frequencies: 50 / 60 Hz Stand-by consumption: less than 1 WOperating temperature: 5 – 40 °CIntegrated fuse (IN side): F1 T0,8A 250 OUT (AC power supply output)Rated voltage: 230 V ± 10%Max. rated current: 500 mAWorking frequency range: 50 / 60 Hz

upply, Installation, Testing & Commissioning of Memory module for actuators - This device is used as a memory module is connected to a system and permanently saves the status of all the actuators configured to manage the lights, after each control sent. Power supply from BUS: 27 Vdc from BUS- Operating power supply with SCS BUS: 18 – 27 Vdc- Absorption: 5 mA- Operating temperature: 0 - 40 °C- Dissipated power with max. load: 0.1 W

Supply, Installation, Testing & Commissioning of 4/8 Scene Programmable Keypad Power supply via BUS: 27 Vdc Operating power supply with SCS BUS: 18 – 27 Vdc Current draw: 9 mA

Supply, Installation, Testing & Commissioning of Configurator Set - This device is used in Configuration box with pliers and system plug Configurator box with 10 configurators 0-9 Specifications Model Other

Supply, Installation, Testing & Commissioning of Analogue Dimmer 1-10 V with 4 Outputs/ CircuitsNumber of supply terminal blocks 1 Number of load terminal blocks 4Connection terminalsTerminal type screwTerminal capacity 2 x 2.5 mm2Number of RJ 45 1 Mains voltage 100-240 V~Frequency 50/60 HzLocation category IndoorsProtection index Penetration by solid andliquid matterIP20(installation in an enclosure)Impact resistance IK04Number of modules 10Operating temperature -5°C to +45°CStorage temperature -20°C to +70°C No-load power consumption 1.9 WWeight 320 gZero current breaking yes

Supply, Installation, Testing & Commissioning of Relay Actuator - This device incorporates four independent relays. The actuator may set two of the four relays in interlocking mode, for the control of loads such as rolling shutter motors, curtain motors Number of outputs: 4x2 A Power supply from BUS: 27 VdcOperating power supply with BUS: 18 – 27 VdcAbsorption: 40 mANumber of outputs: 4x2 A

Supply, Installation, Testing & Commissioning of Relay Actuator - This device incorporates two independent relays with a common terminal for the activation of four loads, and includes local control pushbuttons for each individual load. Number of outputs: 2x10A Power supply via BUS: 27 VdcOperating power supply with BUS : 18 – 27 VdcInput: 5 mA (stand-by)55 mA (max - single loads)30 mA (max - interlock)Number of outputs: 2x10AOperating temperature: (0) – (+40) °C

Supply, Installation, Testing & Commissioning of Configuration modules for Keypads

Supply, Installation, Testing & Commissioning of , of Bus cable for Bus inter connection External sheath colour: grey (RAL 7001)External sheath diameter: 5.5 +/0.1mmExternal sheath thickness: 0.8 mmExternal sheath material: PVC (RZ)Number of internal conductors: 2 unshielded twisted flexible conductors withsheathColour of internal conductors: white and blueSheath thickness of internal conductors: 0.60 mmSheath diameter of internal conductors: PVC (R2)Conductor material: red electrolytic copperConductor section: 0.35 mmq (12 x 0.20 mmq)Operating temperature: 15 70°CMaximum short circuit temperature: 150 °CCoil length: 100 m or 500 m

Supply, Installation, Testing & Commissioning of DISTRIBUTION BOX FOR HOUSING BACK END I.E DIMMERS AND RELAYS

PART A : SOUND REINFORCEMENT SYSTEM

Supply, Installation, Testing & Commissioning of Minimum Two Way, better Three way, minimum Bi or better Tri-amplified FOH Line array speakers, frequency range: 68Hz to 18 Khz or better, loudspeaker consisting of Min 2 x 8" LF driver or better and 1x 3" HF compression driver or better, Nominal Horizontal Dispersion: 120° or better, Impedence-16/8/4 Ohm; Maximum Peak SPL - HF: 133dB, MF 128dB, LF 128dB, Power Continuous HF: 85 watts or better, MF: 250 watts or better, LF: 250 watts or better. Enclosure Material 15 mm birch plywood. Minimum 4 speakers for one set of line array for better system control.

Supply, Installation, Testing and Comminssioning of OEM supplied Array Frame for Line Array Speakers.

Supply, Installation, Testing & Commissioning of 10-inch, Full range, 2-Way Passive Loudspeaker. Frequency Range (-10 dB)-50 Hz–19 kHz, Power capacity - 250W, Sensitivity-92 dB, Maximum Peak SPL-122dB, Coverage Angle-90° conical, LF Driver - 10-inch with 2.5-inch Voice Coil, HF Driver- 1-inch Exit, 1.4-inch voice coil, compression driver. Nominal Impedance-8Ω, Complete with mounting bracket.

Supply, Installation, Testing and Commissioning of Flyable Subwoofer Module with Minimum 2x12"or better; Frequency range 32Hz -107 Hz or better; Max Peak SPL 135dB or better, Impedance - 4 Ohms, Power capacity- 1100 watts or better.

Supply, Installation, Testing & Commissioning of of 2 x 18" High Power ground stacked subwoofer System. Continuous Power Capacity - 1000W or better,Sensitivity (1W @ 1m) - 101 dB or better, Max Peak SPL - 140 dB or better, etc complete as reqd

Supply, Installation, Testing & Commissioning of 4-Channel Class-D Network Amplifier for FOH System and Subwoofers. Total Power - 8000W which can be asymmetrically distributed across amplifier channels. Max Power/Channel 8Ω-1250 W, 4Ω-2400 W, 2Ω-2750 W, 70V/100V - 1250 W. Bridge and Parallel modes for combining multiple channels. Typical Distortion- 8 Ω-0.02 - 0.05%, 4 Ω-0.04 - 0.1%, Frequency Response (8 Ω)-20 Hz - 20 kHz +0.2 dB / -0.7 dB, Input impedance->8k balanced and >4k unbalanced, Front Panel With Display, Controls Knobs, Buttons and indicators Ethernet Ports - 2 Gigabit ethernet ports for network redundancy.

Supply, Installation, Testing & Commissioning of 8-Channel Class-D Network Amplifier for FOH System and Front FIlls. Total Power - 4000W which can be asymmetrically distributed across amplifier channels. Max Power/Channel 8Ω/4Ω-1000W, 2Ω-800W, 70V/100V - 1000W. Bridge and Parallel modes for combining multiple channels. Typical Distortion- 8 Ω-0.02 - 0.05%, 4 Ω-0.04 - 0.1%, Frequency Response (8 Ω)-20 Hz - 20 kHz +0.2 dB / -0.7 dB, Input impedance->8k balanced and >4k unbalanced, Front Panel With Display, Controls Knobs, Buttons and indicators Ethernet Ports - 2 Gigabit ethernet ports for network redundancy.

Supply, Installation, Testing & Commissioning of 6.5-inch, 2 way, wall-mount loudspeaker. Rated impedance- 8Ω, Transformer Taps- 70V/100V:30/15/7.5 Watts, Frequency Range-60Hz – 20kHz or better, Rated noise power-30 watts or better, Sensitivity-86 dB SPL or better, Coverage- 130° conical (500 Hz to 5 kHz) or better, Maximum continuous SPL-97 dB or better, Maximum peak SPL- 107dB or better, Mounting Brackets Included.

Supply, Installation, Testing & Commissioning of Quad channel class-D amplifier for Green and Control room Speakers. Wattage per Channel - 100 watts/channel into Low-Z loads (8Ω/4Ω). and 2x175 watts into 70V/100V. Signal to Noise (A weighted, 20 Hz-20 kHz)->100 dB, Frequency Response-20Hz-20kHz, Input Impedance->10 kΩ balanced/unbalanced, Front Panel Indicators for Power and per channel Signal/Protect/Limit, Mounting brackets included.

Supply, Installation, Testing & Commissioning of Digital Signal Processer. Mic/Line Inputs - 12 or better, Line Outputs- 12 or better minimum 8x8 Dante Channels, Network Channels - 128x128 via AES67/Dante or better, USB Audio - 8x8 or better, Control & Configuration Ports - Ethernet, RS232, 8x8 GPIO or better. Processor should be compatible with network based amplifiers and shall monitor and control amplifiers. Processor shall have capability to control devices mentioned in this BOQ via Ethernet, RS232, IR or GPIO. Note : Network Expander can be added to match the port requirement and Control system can be added as software or hardware (i.e., Crestron/Extron) to control the equipments mentioned in the BOQ. Complete as per specifications as required.

Supply , Installation , Testing & Commissioning of 32 channel mixing console with stage box, 40-input Mic/Line, Effects, Mid-sweep 3-band mono channel EQ, 4-band stereo channel EQ, 6 buses for flexible signal routing: main stereo bus, four group buses, six auxiliary buses, and send buses for the two internal effect processors, Slot for optional Digital I/O card, CAT 5, Should Support MADI/Dante/cobranet Cards, 32 Channel Stage Box. etc. complete with installation as per the site requirement.

Supply, Installation,Testing & Commissioning of Stage box 32 analogue inputs and 8 line outputs making a 32 x 8 matrix.Complete with installation & acessories as per the site requirement.

Supply , Installation , Testing & Commissioning of UHF Digital Wireless Lavalier / Handheld Microphone System, License-free 2.4GHz operation, 24-bit/48 kHz uncompressed audio, AES 256-bit encryption, Simultaneous operation: up to 8 coexisting systems, Working Range: 30m, Frequency Response:20 - 20000 Hz, Signal-to-noise>57 dB-A, Battery Life 12 Hours, Mic Sensitivity:13 mV/Pa, Mic Polar : Cardioidc. complete with installation as per the site requirement.

Supply , Installation , Testing & Commissioning of Dynamic, Vocal / Instrument Wired Handheld Microphone, super cardioid polar, 50-16,000Hz, 100-14,000Hz (1m) etc. complete with installation as per the site requirement.

Supply , Installation , Testing & Commissioning of Microphone Stand etc. complete with installation as per the site requirement ( Floor / Table /Boom).

Supply , Installation , Testing & Commissioning of 18inch length Gooseneck Podium Microphone, complete with installation as per the site requirement. With on/off base switch.

Supply , laying , Testing & Commissioning of Speaker Cable, 2 Core 4 Sqmm stranded ETP high-conductivity copper conductors, PVC insulation, parallel: (1) tinned, (1) bare etc. complete with installation as per the site requirement.

Supply , laying , Testing & Commissioning of Speaker Cable, 2 Core 2.5 Sqmm stranded ETP high-conductivity copper conductors, PVC insulation, parallel: (1) tinned, (1) bare etc. complete with installation as per the site requirement.

Supply , laying , Testing & Commissioning of Microphone Cable 23/0.76 ATC PVC Sheathed

Supply , Installation , Testing & Commissioning of the floor junction boxes on the stage for the various mic inputs with Mic xlr inputs on the boxes .

Equipment Rack 42 U

PART B : VIDEO PROJECTION SYSTEM

Supply , Installation , Testing & Commissioning of Digital Projection System with , Laser Phoshorus with 20,000 hrs life ,16:10 , Brightness Not Less Than 25000 Lumens , Contrast Ratio Minimum 2000000:1 , Technology DLP 3-Chip , Resolution 4K UHD (3840 x 2160) , 3 D Ready , Connectivity HDMI x 2 (HDMI 2.0b, HDCP 2.1 Compliant), DVI-D, DisplayPort (versions 1.2)), RS232 In. Complete with Mounting Hardware. Should include Long Throw Projection Zoom Lens to project size desired screen size from projector. Note Vendor to supply the lens as per actual measurement taken from site.

Supply, Installation, testing & commissioning of Motorised Projection screen 8800 mm (w) x 5500 mm(h) with 1.2 gain, Seamless surface, 3 Step locking position, 16:10 aspect Ratio. Complete with LVC for Control through touch panel, as per the specifications, complete as required.

Supply, Installation, testing & commissioning of 2400X1350 LED Video Wall of 1.25MM pixel pitch, 640000 Pix / Sq-Mtr, Active LED based on the native SMD module, Diecast Al cabinet front loaded, having 16:9 aspect ratio including accessories and mounting frame as required as per site. Data processing 16 Bit, Refresh rate 3840 Hz or better. The Fine Pitch Active LED panel should have the easy maintenance capability having Aluminium chasis with front serviceability onsite. It should have integrated/external 4K Prime - AIO Controller . Minimum OEM warranty of 7 years. MInimum 5% modules to be supplied alongwith the LED.

Supply, Installation, Testing & Commissioning of 4K @ 60 fps PTZ Camera with minimum 30X Optical Zoom, min 100 Presets, Ethernet Out, HDMI Out, 12G-SDI Out, Audio In, Ethernet/RS232/422 Controls, -170° ~ +170° Panning angle, -30° ~ +90° Tilting angle , Should support PoE++. OEM should be CE, RoHS & FCC Certified. Complete with all accessories as per specifications and directions of engineer in charge.

Supply, Installation, Testing & Commissioning of Cable Cubby/Floor Boxes with pneumatic movement and mechanical latching mechanism, Compact size with rectangular bezel, Top surface in black anodized finishes, One CAT 6 RJ-45 network/Data connectors, One unswitched AC outlet,Minimum One input on HDMI and One Input on DP. Complete with all accessories as per specifications

Supply installation Testing & Commissioning of Wireless presenter, Includes 1x HDMI IN and 1xHDMI Out,1xEthernet. Supports presentation from MacOS, iOS, Android, Windows, ChromeOS. Support for Miracast and Airplay, Resolution 1080p60hz. SHould support multiple presentation layouts. Should offer customisable welcome screen, logos, integration with MS O365, GSuites for displaying the meeting room schedule and calender. It should allow guests to connect to wifi hotspot that it creates.

Supply Installation Testing & Commissioning of Touch Control System with 8" or bigger Touch panel for Table Mounting, to control AV equipments & secondary wireless control on 9" or more IPAD & complete with perpetual software and licenses for IPAD.

Supply , Installation, Testing & Commissioning of AV Over IP Scaling Multimedia Encoder, Resolution upto 4K60 4:4:4 ,Range upto 100 meters , PoE (Power over Ethernet) , Video input: HDMI Type A, female , Video output: 1x LAN RJ45 connector , Audio input:1x 3.5mm L/R Analogue audio , Audio output connectors: 1x 3.5mm L/R Analogue audio , Network Audio Support for Dante/AES67 or similar. Ethernet port: 1x LAN RJ45 connector , Content protection-HDCP2.2, RS-232 Serial port: 1x 3-Pin Phoenix connector , USB/KVM Port: 1x USB - Type A and B , GPIO Ports and as per the specifications, complete as required. NOTE : If Encoder if capable of encoding single HDMI Source, match the quantity with required accessories to fulfill the requirement (Total Inputs 15). Encoder/Decoder should be from same OEM.

Supply , Installation, Testing & Commissioning of AV Over IP Scaling Multimedia Decoder, Resolution upto 4K60 4:4:4, Video Input Connectors: 1x LAN RJ45 connector, Video Output Connectors: HDMI Type A, Ethernet port: 1x LAN RJ45 connector, Network Audio Support for Dante/AES67 or similar,Content protection-HDCP2.2, RS-232 Serial port: 1x 3-Pin Phoenix connector , USB/KVM Port: 2x USB - Type A & Type -B, GPIO Ports as per the specifications, complete as required. NOTE : If Decoder if capable of decoding single network stream, match the quantity with required accessories to fulfill he requirement (Total Output 16). Encoder/Decoder should be from same OEM.

Supply, Installation, Testing & Commissioning of minimum Professional 42" LED TV min 350NITS , MTBS50000 hrs Builtin speakers. Operation 24x7.

Supply, Installation, Testing & Commissioning of Professional 75" LED TV min 350NITS , MTBS50000 hrs Builtin speakers. Operation 24x7.

SITC of Supply of Recorder and streamer with inbuilt capacity of recording and streaming with 4 HDMI Inputs and IP video sources, 3 x H.264/AVC digital video over Ethernet 2 x HDMI output, scaling and window processing, supports PIP, PBP and up to 4 windows layout and mixing, 1TB HDD internal storage, Audio Input: 4 Line In/MIC In, Audio Output: 3 x Stereo, 2 x USB, 1 x RS-232 /RS-485 port along with 1 x RJ-45 ethernet port.

Supplying, installation, testing and commissioning of 48 x 10/100/1000 Base T RJ45 Ethernet ports with POE++ as per site requirement with following specifications: Should have minimum 4x 1G Base SFP+ ports for uplinks. Switch should have internal redundant power supply and redundant fans. Minimum switching capacity: 128 Gbps or more Minimum forwarding rate: 95 Mpps or more Switch should have minimum of 1GB of internal DRAM and 2GB of internal Flash memory. Should support dedicated stacking ports with minimum of 80 Gbps stacking bandwidth to put minimum 9 switches into a single stack group (in addition to switching bandwidth and ports specified above.) for future requirement. Should have 8K IPv4 Routes and 2K IPv6 Routes. Should support minimum 16K MAC Address and 4K active VLAN's Should support minimum 6K IGMP Groups. Should support minimum 4K ACL's Should have minimum 4MB of packet buffer size for traffic to support huge file transfers. Should have inter-vlan routing and static routes for IPv4 and IPv6 and upgradeable to support PBR, OSPF ,bgp and PIM- SM /DM as and when required. Should support 802.1d, 802.1s, 802.1w, 802.3ad and 802.1x protocols Should support IGMP snooping v1, v2 & v3. Should have Netflow / Jflow / Sflow. Warranty - Must be quoted with the three years comprehensive replacement and direct OEM 8 x 5 NBD Support pack.

Cable

Supplying & laying of SFTP cable ( Cat6a) complete as per the specifications and as required.

Supply,Installation,Testing & Commissioning of HDMI Interface Cable On a male HDMI type A, 18Gbps bandwidth support, 24K gold–plated connector , Material: Tinned Copper/Bare Copper Type: Triple shielding , JACKET Material: PVC ,Length 1.8 meter and as per the specifications , complete as required.

Supply,Installation,Testing & Commissioning of HDMI Interface Cable On a male HDMI type A,18Gbps bandwidth support,24K gold–plated connector , Material: Tinned Copper/Bare Copper Type: Triple shielding , JACKET Material: PVC ,Length 5 meter and as per the specifications , complete as required.

PART C: STAGE EFFECTS LIGHTING SYSTEM

SUPPLY INSTALLATION TESTING AND COMMISSIONING of MAIN CURTAIN made out of Inherently Fire retardant velvet ( Nextgen / Raymonds / Vimal) curtain cloth with horizontal sliding arrangement complete with fixing rails, brackets, sliding arrangement & motorized operation complete with runners, master runners, pullies, 3mm steel wire rope, 1 HP motor (Crompton/Kirloskar / Bajaj) 2nos. air breaker contactors (L&T/SIEMENS), 2nos. micro switches for auto stop, 3 nos push buttons for forward, reverse and stop positions. The curtain should be draped to half area when in closed position. Minimum overlap at centre should be 900mm and should be stitched in double gathering with Masking Frill 500mm Drop from Proscenium . Including front frill in same cloth complete with accessories. Appx. Size:- 15.5mx 8.0m.

SUPPLY INSTALLATION TESTING AND COMMISSIONING of REAR / MID CURTAIN (Nextgen / Raymond /Vimal) made out of Inherently Fire treated black colour crepe cloth with horizontal sliding arrangement complete with fixing rails, brackets, sliding arrangements & motorised operation complete with runners, master runners, pullies, 3mm steel wire rope, 1HP motor (Crompton) 2nos. air breaker contactors (L&T/SIEMENS), 2 nos. micro switches for auto stop, 3nos. push buttons for forward, reverse and stop positions. The curtain should be draped to half area when in closed position. Minimum overlap at centre should be 900mm and should be stitched in double gathering. size 16mX8m

SITC of MS pipe Lighting Bar : to be provided at FOH & Stage to be fixed from the existing main structure Girder / Grid / Beams / Ceiling, ; approx. size 15m x 50mm dia B-class, supported by brackets ; duly painted black ;

SITC of MS pipe Side Light "Ladder" brackets : with 3-sections, to be provided on either sides for Side Lights - using 1.5" square MS Tube ; to be fixed from the existing main structure Girder / Grid / Beams / Ceiling ; approx. size: 1.75ft.x 6ft. ; duly painted black ;

SITC of WIRING for DIMMABLE Points: using 2.5 sqmm FRLS wire with common neutral & earth for every 2 points ; starting from the patch panel (side of stage) to the Lighting bars/tree or stage points ; terminated at junction box with 2 x 3-pin CEE 16 Amp. Industrial sockets ; cabling laid in PVC conduits

SITC of WIRING for DIRECT Points: using 2.5 sqmm FRLS wire with common neutral & earth for 2 sockets/box ; starting from the MCB Box, having 10A SP MCBs, to the Lighting bars/tree or stage points ; terminated at junction box with 2 x SHUCKO 16 Amp. Sockets/per point (all points to be marked & numbered) ; cabling laid in PVC conduits

SITC of Cycloram of with PVC cycloram screen as per the design drawings complete on a MS tubular frame

SITC of 200 W LED FRESNEL LIGHT Features: 200W cool white LED, Life: More than 30000 hrs, Field Angle: Spot Light (1/10 peak), 29- degrees; Soft Light (1/10 peak), 97-degrees, Manual zoom, Color Temperature: 5000K, Color Rendering Index: Ra=84, Dimmer: 0-100% linearly adjustable, Channel: 1 channel for dimmer, Housing: High-intensity die-casting aluminum, IP20

SITC of LED PROFILE SPOT LIGHT 200W LED Profile Spot Light, Power Supply: AC100V-240V, 50-60 Hz, Power Consumption: Max. 260W, LED: 200W 2 in 1 Cool White & Warm white Color, LED Life time: over 50,000 hours, high quality optical system, Light Angel: 19°/26°/36°/50°, Control Mode: DMX, Auto run and Master/Slave, DMX Channels: 2/5CH, Housing: Plastic, Color: Black, IP Rating: IP20, Net weight: 6 kgs, gross weight: 8 kgs, dimensions: 660x285x295mm.

SITC of 1000W, 240 Volt, PAR Sealed Beam Light with CRC Sheet Metal and aluminum die casting, mat black color, yoke & clamp.

SITC of 180W RGBW LED Bar,C100V-240V, 50-60 Hz, Power Consumption: Max. 260W, LED: 180W 2 in 1 Cool White & Warm white Color, LED Life time: over 50,000 hours, high quality optical system, Light Angel: 19°/26°/36°/50°, Control Mode: DMX, Auto run and Master/Slave, DMX Channels: 2/5CH, Housing: Plastic, Color: Black, IP Rating: IP20, Net weight: 6 kgs, gross weight: 8 kgs,

SITC of LED PAR: 54 x 3W (12R +18G + 12B + 12W), 15º/30º/45º/60º LED PAR of IP 20 rating, having life of 30,000 Hrs & delivers 4200 Lumens. The fixture should have capability to work on standby mode, via DMX 512 or integrated sound – 2 light program.

SITC of 200 W LED PLANOCONVEX LIGHT - warm white LED, DMX 512, Life: More than 30000 hrs, Field Angle: Spot Light (1/10 peak), 10-40-degrees; Soft Spot Light (1/10 peak) 97-degrees, Manual zoom, Color Temperature: 3200K, Color Rendering Index: Ra=84, Dimmer: 0-100% linearly adjustable, Channel: 1 channel for dimmer, Housing: High-intensity die-casting, aluminum, Painted in black matte color, 1.5 sq.mm x 3 core copper wire with 5 Amp plug top and suitable clamp, IP20.

SITC of 200 W LED Flood light with Barn Doors, COB, DMX 512, Painted in black matte color, 1.5 sq.mm x 3 core copper wire with 5 Amp plug top and suitable clamp & suitable clamp.

SITC of DMX Splitter with one DMX input and 6 buffered outputs and 3 pin / 5 pin XLR connectors.

SITC of Lighting Control Console Control up to 108 fixtures - including LED, Moving Lights and conventionals • 48 multi-function faders • 97 playbacks (each with submaster & full cuestack functionality) • 96 groups, 4 x 96 palettes (Colour, Beamshape, Position, Effect) • DVI-D output for optional external touch screen (1024 x 768) • Multi-touch interfaces for Colour & Moving Lights • Dedicated GO button & playback fader for theatrical control • Hands-on intuitive control via 4 encoder wheels • Free mobile apps for wireless control of your ZerOS console on iOS and Android devices • Multi-lingual step-by-step touch screen guidance • Art-Net 4 and sACN for network output & wireless connection to smart phone / remote monitors • 7” multi-touch screen • Automatic Groups, Palettes, Effects and Macros • Colour picking, mixing & image capture • Mood Boards by LEE Filters • Additive, subtractive and HSV control • Store single or multiple cues on each of the playbacks • Built-in fixture library • RDM compatibility • Showfile compatibility with other ZerOS consoles • Quiet, dust free, fanless operation • One DMX universe, upgradable to two universes • Two XLR Outputs (1 x 5 pin + 1 x 3 pin).

SITC of Cable Tray Complete with accessoreis of size 300x40. Complete with accessoreis as required.

SITC of Clamps & Safety Chains

Description of Work / Item(s)

Amount

EQUIPMENTS

WATER COOLED CENTRIFUGAL MAGNETIC CHILLING MACHINES

AHRI Certified 550 TR Water Cooled Magnetic Centrifugal Chiller with VFD

Supply, installation, testing and commissioning of Water Cooled magnetic Centrifugal type chilled water packaged refrigerant machine of actual capacity 550 TR with complete all accessories as required & as per specifications :Chillers: Factory assembled and tested (AHRI certified) magnetic centrifugal chillers using R134a refrigerant. There must be 3 compressors per chiller. The compressor shall have mechanism for stable operation at part loads. Refrigerant shall be CFC free, zero ODP & as per ASHRAE safety classification of A1.Advanced Microprocessor based control panel with automatic controls, coloured & graphical display, complete with accessories and BMS compatible BACNET/MODBUS Protocol with BMS cards.Centrifugal compressor shall be open/ semi-sealed/ totally sealed type. It shall be working on refrigerant R134a The compressor shall be equipped for modulating the capacity from 100% up to the 20% for stable operation without surging. A variable speed drive will be factory fitted and supplied with the chiller. It will vary the compressor motor speed by controlling the frequency and voltage of the electrical power to the motor. The sound level of the unit at 100% load must be less than or equal to 83 dBA at 1 m distance from the unit

Chiller capacity shall be as per following parameters:

Actual Capacity : 550 TR Country of origin : India/Usa/Europe Condenser Water IN : 32 Deg C or 89.6 Deg F Condenser Water OUT : 36 Deg C or 96.8 Deg Flow Rate at tender conditions : 2143 US GPM Evaporator Water IN : 12 Deg C or 53.6 Deg F Evaporator Water OUT : 7 Deg C or 44.6 Deg F Evaporator Flow Rate at tender conditions : 1462 US GPM Fouling factor : Condensor : 0.000500 h·°F·ft²/Btu Minimum COP at 100% load at AHRI : 6.50 Maximum IPLV at AHRI : 0.295 KW/TR Minimum COP at 100% load at tender conditions : 6.15

AUTOMATIC TUBE CLEANING SYSTEM FOR CONDENSERS 550 TR CHILLERS)

Supply, Installation, Testing and Commissioning of Automatic Tube Cleaning system for 3# Water cooled Magnetic Centrifugal Chillers of 550TR each. The ATCS System can be individual to each chiller or may handle multiple chiller at a time with a common skid.Complete system including all low side work to be provided by manufacturer.

Chiller plant manager

CHILLED WATER TYPE HYDRONIC SYSTEM:

Supply,Installation, testing and commissioning of chilled water cassette type hydronic units with the decorating panel, In-built condensate drain pump, etc. It is suitable for operation on 230(220-240V) volts, 50Hz, 1 phase AC power supply. Complete in all respect. All units should have 4 Row Deep cooling coils.

4.0 T.R, 4 RD Four-Way Cassette type indoor unit

3.5 T.R, 4RD Four-Way Cassette type indoor unit

3.0 T.R,4 RD Four-Way Cassette type indoor unit

2.5 T.R,4 RD Four-Way Cassette type indoor unit

2.0 T.R,4 RD Four-Way Cassette type indoor unit

1.5 T.R,4 RD Four-Way Cassette type indoor unit

1.0 T.R,4 RD Four-Way Cassette type indoor unit

CHILLED WATER HI - WALL TYPE

1.5 TR HI -WALL CFM-510

1.0 TR HI- WALL CFM-620

Air Handling Unit

Supply, installation, testing and commissioning of AHU. Unit comprising of prefilter section, mixing box, cooling coil Unit and other sections complete in all respects with VFD shall be 43mm thick double skin panel with thermal break profile.Unit shall be AHRI certified as per AHRI/ANSI 1350 with min. below mechanical performance rating :With Mixing Chamber ,Casing Deflection : CD2, Casing Leakage : CL2 Thermal Transmittance : CT3 ,Thermal Bridging : CB2

65 TR AHU 26000 CFM , Floor Mounted 50mm WG

35 TR AHU 14000 CFM , Floor Mounted 50mm WG

30 TR AHU 12000 CFM, Floor Mounted 50mm WG

25 TR AHU 10000 CFM , Floor Mounted 50mm WG

20 TR AHU 8000 CFM , Floor Mounted 50mm WG

8.0 T.R AHU 3200 CFM , Ceilling/ Floor Mounted 30mm WG

6.0 T.R AHU 2400 CFM, Ceilling Mounted 30mm WG

PUMPS

Supply, installation, testing and commissioning of CENTRIFUGAL horizontal end suction type pumps. Factory mounted on a common base with electric motor for recirculation of water for the central Air conditioning system. All pumps motor shall be aligned properly as required. The pump motor shall be suitable for 415 +(-) 10% volts. 50 cycles, 3 phase power supply. The quoted price shall include cost of thermal insulation and cladding for chilled water pumps. Pumps with performance characteristics as given below:-

Primary Chilled water Pump

Capacity : 1608 USGPM at APPX 67 HP (20 to 30Mtr Head)

Secondary chilled water Pump

Capacity : 1608 USGPM at APPX 67 HP (20 to 30Mtr Head) 50KW VFD

Condenser water Pump

Capacity : 2357 USGPM at APPX 98 HP (25 to 35 mtr Head)

Cooling Tower:

Supply, installation, testing and commissioning of induced draught cross flow type cooling towers each complete with FRP basin having auxilary rectangular suction tank at bottom. The basin shall be complete with connections for drain, overflow, makeup water, quick fill and float valve, plus hot dipped galvanised suction strainer FRP body of sufficient strength to with stand wind velocities upto 60 m/s, vibration and earth quakes, fan and motor assembly conforming to IP-55.protection for outdoor operation fill media of honeycomb design arranged in the suitable pattern for each of replacement, distribution pipes consistings of spray type arragement on top of the main supply standby, overflow pipe, ladder, vibration isolation pads, cables, controls etc. As per specification and drawing.

700 T.R. ,NO OF MOTOR WITH 15 HP - 6

PIPING

Supply, installation, testing and commissioning of MS 'C' class pipes cut to required length with necessary, clamps, supports, hangers,fitings, such as bends, tees, reducers etc. and installed with all weided joints complete as per specification & drawings.

400 mm dia MS pipes of 9 mm thickness.

350 mm dia MS pipes of 9 mm thickness.

300 mm dia MS pipes of 6 mm thickness.

250 mm dia MS pipes of 6 mm thickness.

200 mm dia MS pipes of 6 mm thickness.

150 mm dia MS pipes of 6 mm thickness.

125 mm dia MS pipes.

100 mm dia MS pipes .

80 mm dia MS pipes.

65 mm dia MS pipes.

50 mm dia MS pipes.

40 mm dia MS pipes.

32 mm dia MS pipes.

35 mm dia MS pipes.

CONDENSER WATER PIPING:

Supply, installation, testing and commissioning of MS class 'C' pipes cut to required length with necessary clamps, supports, antivibration, hangers, fittings such as bends, tees, reducers etc. and installed with all welded joints complete as per specification & drawing.

450 mm dia MS pipes of 9 mm thickness

300 mm dia MS pipes of 6 mm thickness.

SUPPLY OF DRAIN PIPE:

SUPPLY,Installation, testing & commissioning of UPVC pipes with 6mm thick nitrile rubber tube insulation complete with all necessary fittings such as elbows, tees, reducers etc and supports such as clamps etc complete as per specification and drawings.

50 mm dia

VALVES

Supply, fixing, testing and commissioning in position the following valves, strainer etc. in chilled Water line complete with flanges etc as per specifications & drawings. Valves should be PN-16 Rating.

Supply, installation, testing and commissioning of Butterfly Valve

300 mm dia. Gearbox operated

250 mm dia. Gearbox operated

200 mm dia. Lever operated

150 mm dia. Lever operated

125 mm dia. Lever operated

100 mm dia. Lever operated

80 mm dia. Lever operated

65 mm dia. Lever operated

50 mm dia. Lever operated

40 mm dia. Lever operated

Supply, installation, testing and commissioning of Check Valve

300 mm dia.

250 mm dia.

Supply, installation, testing and commissioning of Ball Valve:

32 mm dia.

25 mm dia.

Supply, installation, testing and commissioning of Balance Valve with nozzle.

300 mm dia.

250 mm dia.

125 mm dia.

50 mm dia.

Supply, installation, testing and commissioning of Automatic Air vent Vavle

Supply, installation, testing and commissioning of Drain Vavle

40 mm dia.

Supply, installation, testing and commissioning of Pot STRAINER

450 mm dia.

Supply, installation, testing and commissioning of Y- STRAINER.

300 mm dia.

250 mm dia.

125 mm dia.

100 mm dia.

50 mm dia.

40 mm dia.

32 mm dia.

25 mm dia.

Supply, installation, testing and commissioning of rubber expansion bellow of suitable pressure rating to be installed at pump suction, discharge and at pipe crossing building expansion joints.

300 mm dia.

250 mm dia.

125 mm dia.

100 mm dia.

Supply, installation, testing and commissioning of 3-Way Motorised Valve for Air Handling Units, cassette unit and ductable units.PN 16

125 mm dia.

100 mm dia.

50 mm dia.

40 mm dia.

32 mm dia.

25 mm dia.

GAUGES

TEMPRATURE GAUGE

Supply, installation, testing and commissioning of dial type temprature gauges with isolating cock valves in both the scales (degree C & degree F). Connection Size 10 MM.

PRESSURE GAUGE

Supply, installation, testing and commissioning of dial type pressure gauges with isolating valves in both the scales (meters & British units). Connection Size 10 MM.

FLOW SWITCH

Supply, installation, testing and commissioning of threaded type digital flow switch. Model:- WFS 6000

Supply, installation, testing and commissioning ofthermostat for controller ( for indoor unit controller)

INSULATION

CHILLED WATER PIPING INSULATION :

Supply, installation, testing and commissioning of38mm thick Nitrile Rubber insulation with allumunium foil face (Density 60kg/m³ ) in 2 layers. Each layer shall 19mm & 19mm thick respectively with protective coating on chilled water pipes & fittings like valves, flanges & unions, etc. as per the approved shop drawings & specifications:

400 mm dia MS pipes of 9 mm thickness.

350 mm dia MS pipes of 9 mm thickness.

300 mm dia MS pipes of 6 mm thickness.

250 mm dia MS pipes of 6 mm thickness.

200 mm dia MS pipes of 6 mm thickness.

150 mm dia MS pipes of 6 mm thickness.

125 mm dia MS pipes.

100 mm dia MS pipes .

80 mm dia MS pipes.

65 mm dia MS pipes.

50 mm dia MS pipes.

40 mm dia MS pipes.

32 mm dia MS pipes.

35 mm dia MS pipes.

FACTORY OR SITE FABRICATED DUCTWORK & ACCESSORIES:

Supply, installation, testing and commissioning of factory or Site fabricated. The ducts shall be constructed per SMACNA standard and made from a GI sheet of lock forming quality having Zinc Coating as per ASTM A525 G90. complete with vanes, splitter dampers, fire retardant gaskets hanging arrangement including fully threaded GI rods and GI "C" channels/ rolled steel wires or Wire Rope Hangers & Supports complete with end fixing, GI "C" channels etc. as approved by clients/consultants by the approved shop drawings and specifications.

Powder-coated extruded aluminum grilles/ Diffusers

Supply & installation and commissioning of powder coated extruded aluminum grilles / diffuser complete with nuts, bolts, screws etc. as per approved drawings and specfications.

VOLUME CONTROL DAMPER (Aluminum) : TRISTAR / CYNOR / BALANCE AIR

Supply, installation and commissioning of Opposed blade Low leakage Aluminum volume control damper with locking arrangement. VCD Construction18G GI in multi-blade with handle and wing nut, clearly marked with open/close, for supply and return air duct branches. (Extended shaft of minimum 150mm length with GI base plate shall be provided wherever required during drawing Approval.

FLEXIBLE CANVASS CONNECTIONS:

Supply, Installation, Testing of 125mm deep antivibration flexible joints. Flexible connections shall be constructed using imported fire retardant fabric with extruded GI frame/flange on both sides.

FIRE DAMPER

UL Listed Fire damper with Actuators -

Supply, installation, testing and commissioning of and fixing of mild steel fabricated opposed bladefire damper complete with actuators.

Actuators

Each damper shall have an externally replaceable combination thermal actuator and fusible link completely exposed to the air streamThe damper shall be automatically reset on resumption of power supply by built-in motor of 220V AC or 24V AC / DC.

THERMAL INSULATION FOR DUCT:

Supply, Installation, testing and commissioning of closed cell elastomeric insulation with microbial treatment of density not less than 50 kg/Cubm and material shall be in the form of sheets of uniform thickness.

13 mm thickness for Supply Air Duct

9 mm thickness for Return Air Duct

ACOUSTIC LINING

Supply, Installation, testing and commissioning of open cell elastomeric insulation with microbial treatment of density not less than 50 kg/Cubm and material shall be in the form of sheets of uniform thickness. The ‘K’ value at 20o C. shall not be less than 0.037 W/mK.

Supply, installation, testing and commissioning of MS Work for piping support , Pump stand and other MS work.

SUB HEAD : ‘A' MACHINERY

Supply, installation, testing and commissioning of VRV/VRF outdoor units with multiple compressors complete with full inverter type scroll compressors, R410A refrigerant, Heating & Cooling Only mode option, G type heat exchanger condenser, low noise direct driven propeller condenser fans in each module with top discharge, outdoor unit more than 14 HP should have minimum 2 nos. condenser fans and 2 compressors.Each outdoor unit should have full DC Inverter scroll compressors and shall be of same OEM make of ODUs. Each system shall have Single/multiple Outdoor unit modules & each module shall have single/multiple Inverter based scroll compressors as per below mentioned capacities. Single module should not exceed 20 HP. In case of any outdoor unit failure, the rest of system should be capable of operation, Automatic Sequencing operation, Automatic Refrigerant Charge function, Microprocessor panel with sequential starting of condensing unit, coils, expansion valves, filters in refrigerant circuits, phase reversal preventer, all vibration isolators, safeties, Operating range of dry bulb temperature -20 to 50 Degree. Major component of machine shall be of NON CHINA origin.

HEAT PUMP 12 H.P. CAPACITY (TOP-DISCHARGE)

HEAT PUMP 16 H.P. CAPACITY (TOP-DISCHARGE)

HEAT PUMP 20 H.P. CAPACITY (TOP-DISCHARGE)

HEAT PUMP 22 H.P. CAPACITY (TOP-DISCHARGE)

HEAT PUMP 26 H.P. CAPACITY (TOP-DISCHARGE)

HEAT PUMP 28 H.P. CAPACITY (TOP-DISCHARGE)

HEAT PUMP 34 H.P. CAPACITY (TOP-DISCHARGE)

HEAT PUMP 44 H.P. CAPACITY (TOP-DISCHARGE)

HEAT PUMP 46 H.P. CAPACITY (TOP-DISCHARGE)

HEAT PUMP 54 H.P. CAPACITY (TOP-DISCHARGE)

HEAT PUMP 56 H.P. CAPACITY (TOP-DISCHARGE)

HEAT PUMP 60 H.P. CAPACITY (TOP-DISCHARGE)

Supply of VRV/VRF outdoor units with complete with full inverter type scroll compressors, R410A refrigerant, low noise direct driven propeller condenser fans in each module Each Outdoor Unit shall have two condensor fan .Each outdoor unit should have full DC Inverter scroll compressors and shall be of same OEM make of ODUs. Automatic Sequencing operation, Microprocessor panel with sequential starting of condensing unit, coils, expansion valves, filters in refrigerant circuits, phase reversal preventer, all vibration isolators, safeties Major component of machine shall be of NON CHINA origin.

HEAT PUMP 12 H.P. CAPACITY (SIDE-DISCHARGE)

INDOOR UNITS

Supply, installation, testing and commissioning of Hi wall type indoor units comprising with per-filter, fan section with low noise fan multi speed motor, with DX coil, outer cabinet, pipe connections.The indoor unit shall have force shutdown valve. The unit shall be capable to adjust the airflow automatically as per requirement.

1.28 TR HI-WALL WITH REFNET & WIREL LESS REMOTE

1.59 TR HI-WALL WITH REFNET & WIREL LESS REMOTE

2.01 TR HI-WALL WITH REFNET & WIREL LESS REMOTE

Supply, installation, testing and commissioning of Round Flow type Cassette indoor units comprising with per-filter,drain pump, fan section with low noise fan multi speed motor, coil section with DX coil, outer cabinet, insulation, pipe connections with human occupancy sensor and Variable Refrigerant Temprature Smart technology and following capacities, • The cassettes units shall have dual sensor which detect the presence of people and floor temperature to provide comfortable air – conditioning and energy saving. The sensor should detects human presence and adjust the air flow direction automatically to prevent drafts. Room temp should be increase up to 4 Deg C or the indoor unit to be switched off when people are not detected. The sensor should detect the floor temperature and automatically adjusts the operation of the indoor units to reduce the temperature difference between the ceiling and the floor.The indoor unit shall have force shutdown valve. The indoor unit shall be capable of adjusting airflow automatically as per requirement

1.28 TR ROUND FLOW CASSETTE WITH REFNET & WIREL LESS REMOTE

1.59 TR ROUND FLOW CASSETTE WITH REFNET & WIREL LESS REMOTE

2.01 TR ROUND FLOW CASSETTE WITH REFNET & WIREL LESS REMOTE

2.56 TR ROUND FLOW CASSETTE WITH REFNET & WIREL LESS REMOTE

3.18 TR ROUND FLOW CASSETTE WITH REFNET & WIREL LESS REMOTE

3.98 TR ROUND FLOW CASSETTE WITH REFNET & WIREL LESS REMOTE

4.55 TR ROUND FLOW CASSETTE WITH REFNET & WIREL LESS REMOTE

Installation, testing and commissioning of Variable Refrigerant Flow type multi unit air-conditioning system complete with indoor and outdoor units with individual controller for cooling type operations.

Additional Gas Charging R-410

Communication Cable

Supply, installation, testing and commissioning of 2c x 1.0 sqmm control cum transmission wiring/power/control cabling with PVC insulated, PVC sheathed, multicore copper conductor control cable in suitable conduits between indoor and outdoor units and its remote controllers.

Supply, Installation, testing and commissioning of Interconnecting Cable 1.5 sqmm into 4 core between indoor and outdoor unit. All material used for Cabling should confirm with green Building rating ).

Refrigerant Piping

Supply, installation , testing and commissioning of Interconnecting refrigerant copper pipe work suitable for R-410A refrigerant with closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as per specifications, all piping inside the room.All piping shall be properly supported with MS,GI HANGERS .All piping shall be pressure tested for 1.5 times the working pressure. . The refregerant pipes running in vertical shaft shall be supported on MS angle and wooden saddle at every 1200 mm distance and the pipes which are running horizontally above the false ceiling should be supported on MS angle/slotted angle at every 1200 mm distance.

Liquid Line including 13 mm closed cell nitrile rubber tubular insulation

Suction Line including 19 mm closed cell nitrile rubber tubular insulation.

Set of Refrigerant Piping for 1, 1.2 and 1.5 TR size (1/4" + 1/2") outer Diameter of pipe 1/4=6.4mm, 1/2=12.7mm wall thickness in mm 0.8mm

Set of Refrigerant Piping for 2 TR size (3/8" + 5/8") outer Diameter of pipe 3/8=9.5mm, 5/8=15.9mm wall thickness in mm 0.8mm

Drain Piping

Supply, installation , testing and commissioning of drain piping complete with fittings, supports, valve and PVC with 6 mm thick closed nitrile rubber foam insualtion / UPVC drain without insualtion as per specifications & drawings.

Supply, installation, testing and commissioning of UPVC Piping with Fitting support as per Requirement. All material used for the Drain piping confirm with green Building rating (IGBC GOLD Rating ). Size: a) 25 mm

CABLE

S&F following sizes (dia.) of ISI marked MMS ( IS:9537 P - III )vergin material PVC conduit as per PWD specification for electrical Works along with its accessories (IS: 3419 ) as required in recess including cutting the wall, covering conduit and making good the same as required. All relative and latest acceptance tests reports by any NABL accredited lab for the conduit shall be submitted before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 202 .

Providing & Fixing of 240/415 V Residual current circuit breaker (RCCB) as per PWD specification for electrical Works with ISI marked (IS:12640-1) / conforming to IEC 61008 -1 , rated conditional s/c current of 10 KA, truly current operated and shall operate on CBCT mechanisum, provision for pad lock, min. operation 10,000 upto 63 A rating and 5000 for 100 A rating, minimum phase termination capacity of 50 sq.mm. rigid wire , IP 20 contact protection with existing distribution board / sheet including making connections, testing etc. as required.OEM shall have submit NABL / CPRI / ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

Four pole 100/300 mA sensitivity

63 A rating

Providing & Fixing of IK09 recessed/surface mounting heavy duty horizontal type sheet steel of 1.6 mm thick Distribution board as per PWD specification for electrical Works ISI marked conforming to IS-13032 & IS-8623 / conforming to IEC 61439-3. Phosphatised/ powder painted complete with suitable rating insulated copper bus bar, shorting link , neutral link, earth link , connecting wire of suitable rating and din bar,masking sheet, including making internal DB terminations with copper lugs and with detachable gland plate, including making connections, testing etc. as required.OEM shall have submit NABL / CPRI/ ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure"A" Rajasthan PWD BSR 202 .

IP-43 Double door (single phase)

Providing & Laying XLPE insulated & P.V.C. sheathed Armoured aluminium cable of 1.1 KV grade as per PWD specification for electrical Works in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench with filling of excavated earth in trench , on existing cable trays or on surface etc. including making necessary connection, testing etc. as required of size and as per points (a), (b), (c), mentioned below:-

(a) Material :- H4- Grade aluminium conductor of purity >99.6 % & as per IS:1554 P-I / IS :7098 P - I

(b) conductor shall have electrolytic aluminium confirming to IS 8130, IS 3975-1999 for armouring of cables in armoured cable items , IS 5831 for sheath, IS 10810 (Part 0 to 64 ) for testing procedures .

(c) OEM Must have ISO 9001 & 14001 certifications for quality assuarance & its own in house NABL lab setup for all testing facilities for cables . Appropriate type test certificate / OEM test report shall be submitted . All above as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 202 .

Laying and fixing of PVC /XLPE power Cable of 1.1 KV grade of following size on wall/ cable tray with saddles/MS flat clamp etc as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 202 .

upto 35 sqmm

above 35 Sqmm and upto 95 sqmm

above 95 Sqmm and upto 185 sqmm

above 185 Sqmm and upto 300 sqmm

Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Un-armoured / Armoured copper cable of 1.1 KV grade as per PWD specification for electrical Works in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench with filling of excavated earth in trench , on existing cable trays or on surface etc. including making necessary connection, testing etc. as required of size and as per points (a), (b), (c), mentioned below:-

(a) Copper conductor of electrlytic grade copper, purity >99.97 % ISI marked as per IS:1554 P-I / IS :7098 P - I

(b) conductor shall made of copper rods confirming to IS 613-1964, IS 3975-1999 for armouring of cables in armoured cable items , IS 5831 for sheath, IS 10810 (Part 0 to 64 ) for testing procedures

(c) OEM Must have ISO 9001 & 14001 certifications & its own in house NABL lab setup for all testing facilities for cables . Appropriate type test certificate / OEM test report shall be submitted . All above as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 202 .

Armoured

Supplying and making one end termination with heavy duty brass compression gland (as per IS 12943- 1990) SIBG type, heavy duty aluminium lugs (as per IS 8309 - 1993 & IS 8337-1976 ) duly crimped with crimping tool, PVC tape as per PWD specification for electrical Works etc for following size of Armoured PVC insulated & PVC sheathed/ XLPE aluminium conductor cable of 1100 volt grade as required of size. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

3.5 x 35.0 sq.mm

3.5 x 50.0 sq.mm

3.5 x 70.0 sq.mm

3.5 x 120.0 sq.mm

3.5 x 150.0 sq.mm

3.5 x 185.0 sq.mm

3.5 x 240.0 sq.mm

3.5 x 300.0 sq.mm

3.5 x 400.0 sq.mm

4 x 10.0 sq.mm

4 x 16.0 sq.mm

4 x 25.0 sq.mm

Supplying and making one end termination with heavy duty single compression brass gland SIBG type, heavy duty Copper lugs duly crimped with crimping tool, PVC tape etc for following size of Armoured PVC insulated & PVC sheathed/ XLPE aluminium conductor cable of 1100 volt grade as required of size.

2 x 25.0 sq.mm

4 x 4.0 sq.mm

4 x 6.0 sq.mm

4 x 10.0 sq.mm

4 x 16.0 sq.mm

4 x 50.0 sq.mm

Supply, Fabricating & installing following sizes of perforated Hot dipped Galvanized iron cable tray ( Galvanized thickness not less then 50 microns) with perforation not more then 17.5% in convenient section including horizontal and vertical bends, reducers tees,cross members and other accessories as required and duly suspended from the ceiling with GI suspenders including GI bolts & nuts , fastners, supports etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 202 .

100mm x 50mm x 1.6mm

150mm x 50mm x 1.6mm

300mm x 50mm x 1.6mm

450mm x 50mm x 2.0mm

600mm x 50mm x 2.0mm

Supply, Fabricating & installing following sizes of powder coated ladder type M.S. cable trays with rungs at span of 250 mm including horizontal and vertical bends, reducers tees,cross members and other accessories as required and duly suspended from the ceiling/wall with MS suspenders including bolts & nuts ,fastners, supports, painting suspenders etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 202 .

600mm x 50mm x 2.0mm

S/F cable route marker with 10cm x 10cm x 5mm thick or of 10cm dia. G.I.plate with inscription thereon, bolted/welded to 35mm x 35mm x 6mm angle iron,60cm long and fixing the same in ground in C C ( 1:3:6 ) as required.All as per pre approved by Engineer in charge. For additional technical parameters of products/work , refer Annexure "A" Rajasthan PWD BSR 202 .

Providing & laying of Double wall corrugated pipe confirming to IS : 14930 P - 1 & 2 with HDPE Coupler at 1 mtr. Depth below the ground for laying cable including making the trench and back filling , compaction of earth as required( Excavation of Earth to be paid Extra as required. ) of following Outer Dia. / Inner dia as per IS:4984:1995. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 202 .

Supply & Laying following size earth strip in horizontal or vertical run in Ground/surface/recess including riveting, soldering, saddles, Jointing shall be done by overlapping and with 2 set of Brass (for Cu strip) / GI (for GI Strip) nut bolt & spring washer spaced at 50cm making connection etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 202 .

25mm x 3mm copper strip

25mm x 5mm copper strip

50mm x 6mm copper strip

25mm x 3mm G.I. ( Hot Dipped ) Strip

25mm x 6mm G.I. ( Hot Dipped ) Strip

50mm x 6mm G.I. ( Hot Dipped ) Strip

Supply & Laying following size earth wire in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection with GI/Cu thimble etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 202 .

8 SWG copper Wire

8 SWG G.I. ( Hot Dipped ) Wire

Plate Earthing as per PWD specification for electrical Works as per IS:3043 with Hot dipped G.I. Earth plate of size 600mm x 600mm x 6.0mm by embodying 3 to 4 mtr. below the ground level with 20 mm dia. G.I. 'B' class watering Pipe ,including all accessories like nut, bolts, reducer, nipple, wire meshed funnel, and Heavy duty weather proof poly-propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height 250 to 300 mm. and embodying the pipe complete with alternate layers salt and coke/ charcoal, testing of earth resistance for value of 5 ohms or less as required & must record by engineer in charge during site visit and ensure to enter in measurment book. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 202 .

Plate Earthing as per PWD specification for electrical Works as per IS:3043 with copper Earth plate of size 600mm x 600mm x 3.0mm by embodying 3 to 4 mtr. below the ground level with 20 mm dia. G.I. 'B' class watering Pipe ,including all accessories like nut, bolts, reducer, nipple, wire meshed funnel, and Heavy duty weather proof poly- propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height 250 to 300 mm. and embodying the pipe complete with alternate layers salt and coke/ charcoal, testing of earth resistance for value of 5 ohms or less as required & must record by engineer in charge during site visit and ensure to enter in measurment book. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 202 .

P & F of Heavy duty weather proof poly-propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height 250 to 300 mm. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 202 .

STAIRCASE PRESSURIZATION

14000 CFM , 50 mm static for Tower-1

13000 CFM , 50 mm static for Tower-2

Supply Installation of electrical starter panel for above fans IP-54 protection made out of 14 SWG Sheet Double door with suitable incomer /Outgoing MCB and starter comprising all protection relays and ready to use with BMS system complete as required by Enginner-In-charge.

LIFTWELL PRESSURIZATION

17000 CFM , 50 mm static for Tower-1

15000 CFM , 50 mm static for Tower-2

Supply Installation of electrical starter panels for above fans IP-54 protection made out of 14 SWG Sheet Double door with suitable incomer /Outgoing MCB and starter comprising all protection relays and ready to use with BMS system complete as required by Enginner-In-charge.

Description of Work / Item(s)

Amount

Supply , Installation , Testing and Commissioning of Acrylic Firestop Sealant Hilti CP 606 or equivalent in gaps around non-combustible penetrants like ducts or metal pipes passing Through Penetration on Floor / wall for mechanical services for annular gaps up to 50 mm to provide minimum 2 hours fire rating when subject to the test conditions of UL 1479/ASTME 814 standards as per detailed specifications given in RFP .(13 mm thickness of sealant)

Supply , Installation , Testing and Commissioning of high performance intumescent firestop sealant Hilti FS One max or equivalent make for Floor / wall through penetration for mechanical services around combustible penetrations upto 2 inches like plastic pipes or ducts/pipes with insulation passing through floor to provide minimum 2 hours fire rating when subject to test standards of UL 1479/ASTM-E 814 as per detailed specifications enclosed .

Supply , Installation , Testing and Commissioning of intumescent flexible firestop wrap strip Hilti CP 648 E or equivalent make for Floor / wall through penetration for mechanical services like for plastic pipe, insulated pipe and various non-metallic penetrations from 2" to 6" diameter passing through floor slab to provide minimum 2 hours fire rating when subject to test standards of UL 1479/ASTM-E 814 as per detailed specifications given in RFP . the work should be executed considering wraps on both sides of wall

Plastic Pipe diameter of 2.5'' (CP 648-E Firestop Wrap), Min. recommended hole dia. in floor: 92 mm

Plastic Pipe diameter of 3'' (CP 648-E Firestop Wrap), Min. recommended hole dia. in floor: 112 mm

Plastic Pipe diameter of 4'' (CP 648-E Firestop Wrap), Min. recommended hole dia. in floor: 132 mm

Plastic Pipe diameter of 5'' (CP 648-E Firestop Wrap), Min. recommended hole dia. in floor: 152 mm

Plastic Pipe diameter of 6'' (CP 648-E Firestop Wrap), Min. recommended hole dia. in floor: 202 mm

Supply , Installation , Testing and Commissioning of ready-to-use firestop collar Hilti CP 644, or equivalent make for Floor / wall through penetration for mechanical services made of a galvanized steel housing and intumescent inserts for firestopping large combustible pipes with diameters from 7" (177 mm) up to 10" (250 mm) passing through floor slab to provide minimum 2 hours fire rating when subject to test standards of UL 1479/ASTM-E 814 as per detailed specifications given in RFP . The work should be executed conidering collars on both sides of wall s

Plastic Pipe diameter of 7'' (CP 644 Firestop Collar)

Plastic Pipe diameter of 8'' (CP 644 Firestop Collar)

Plastic Pipe diameter of 9'' (CP 644 Firestop Collar)

Plastic Pipe diameter of 10'' (CP 644 Firestop Collar)

Supply , Installation , Testing and Commissioning of Fire stop mortar system Hilti CP 636 or equivalent make Through Penetration on (Medium to large size i.e. > 4" gaps) For through penetration for wall / floor mechanical and electrical services , with minimum 2 hours fire rating when tested in accordance with UL 1479/ASTM-E 814 standards, for horizontal openings in floors or slabs after passing service lines like cables/cable bundles, cable trays etc. as per detailed specifications given in RFP . The material should be applied considering 65 mm thk mortar with 0% occupancy.

Supply , Installation , Testing and Commissioning of rodent and termite proof Fire Barriers Hilti CFS COS ( Composite Sheet) system or equivalent make for 2 hours fire rating when tested in accordance with ASTM E 814/UL 1479 standards - Under Panel Sealing (Medium to large size i.e. > 4" gaps) For through penetration for wall / floor mechanical and electrical services The Composite Sheet 3.81 mm thick, bonded with organic/inorganic fire-resistive elastomeric #SS 304 (Stainless steel) sheet. One side it should be bonded with 26 gauge #SS 304 (Stainless steel) sheet and the other side it should be reinforced with hexagonal shaped #SS 304 (Stainless steel) wire mesh and covered with aluminium foil for the penetrants and the big opening as per detailed specifications given in RFP .

Supply , Installation , Testing and Commissioning expanding firestop foam Hilti CP 620 or Equivalent make , with minimum 2 hours fire rating when tested in accordance with UL 1479/ASTM-E 814, for through Penetration on wall / Floor for sealing inaccessible, complicated or annular gaps openings for horizontal openings in floors or slabs made of concrete/ masonry or Gypsum after passing service lines like cable trays or cables/cable bundles as per detailed specifications given in RFP .

Supply , Installation , Testing and Commissioning of Firestop Factory-assembled cable device Hilti Speed Sleeve (CP 653 BA) or Equivalent make for Communication Cables Sealing with repenetrating facility for floor / wall , containing an intumescent material and a flexible cloth which limits the warm and cold smoke propagation to less than 1 CFM per device for passing cables through floor slab to provide minimum 2 hours fire rating when subject to test standards of UL 1479/ASTM-E 814. No additional material shall be required for adding or re-moving cables after the first installation as per detailed specifications given in RFP ..(Note: for server rooms and data centers and areas where frequent maintenance is required as directed by engineer in-charge. )

CP 653BA (2" Size)

CP 653 BA (4" Size)

Supply , Installation , Testing and Commissioning of Acrylic Firestop Sealant Hilti CP 606 or Equivalent make in gaps between wall and slab made of concrete/masonry/gypsum on both sides of wall to provide minimum 2 hours fire rating when subject to the test conditions of UL 2079 & ASTM E 1966 standards with Min. movement capability of +_12.5%. as per detailed specifications given in RFP .( measurements will be based Consideting 25mm joint width and 1 R Mtr length with 13mm thickness on both sides of wall )

Supply , Installation , Testing and Commissioning of sprayable Fire-rated joint spray Hilti CFS SP WB or Equivalent make in gaps between vertical concrete/masonry wall and deck slab to provide minimum 2 hours of fire rating when tested as per UL 2079 standard as per detailed specifications given in RFP . (measurements will be made on R mtr Considering 100mm joint width & 3 mm WFT, wet film thickness )

Supply , Installation , Testing and Commissioning of silicone based firestop Sealant Hilti CP 601S or Equivalent make in horizontal & vertical movement or expansion joints to provide minimum 2 hours fire rating along with movement capability of +_25% when subject to the test conditions of UL 2079 standards as per detailed specifications given in RFP .(Measuremet will be made on R mtr Considering 50 mm joint width and 13mm thickness on both sides of wall)

Supply , Installation , Testing and Commissioning of intumescent based coating Hilti CP 678 or Equivalent make on internal cables/bunch cables & cable tray for at least 1 mtr in every 14 Mtrs for horizontal runs and to entire length of vertical runs . The coating shall have a density in the range of 1.2 to 1.4 Kg/ L. The coating shall be non-toxic, asbestos and halogen free and shall have good mechanical strength as per detailed specifications given in RFP . . (measurement will be made by R mtr x Diameter of cable in Mtr giving area in Sq mtr )

Supply , Installation , Testing and Commissioning of ablative coating Hilti CP 679A or Equivalent make on external cable/ bunched cables in enclosed and semi-enclosed cable runs to be coated at least 1 mtr in every 14 mtrs of cable runs for the horizontal runs and to entire length of the vertical run as per IEC 60332 part.3 tested by DNV' interpretation of SOLAS 1974 as per detailed specifications given in RFP . (measurement will be made by R mtr x Diameter of cable in Mtr giving area in Sq mtr )

Supply , Installation , Testing and Commissioning of All cables penetrations of fire-rated walls or floors shall be sealed with a Hilti CFS CTS (multi-cable transit block) or Equivalent make system for use in multi-cable transit frames. The multi-cable transit system should cover all cable diameters from 4 core 6 Sq mm to 400 Sq mm , #.5 core with a module adapter system where no peeling of single layers is necessary as per detailed specifications given in RFP . (only for high tension cable wires )

Description of Work / Item(s)

Amount

Fees for following consultant along with their representatives at site to accomplish the job related to Building and to submit the conceptual, working and as built drawings (gate House, Academic Block, Faculty Block, Hostel 5 Blocks, Non teaching Blocks, Dean and Director residence, Workshop, Guest House, Landscape and Others within digital fintech institute plot area)

Fees for Vendor appointed structural consultant for entire project

Fees for Vendor appointed architect

Fees for Vendor appointed landscaping consultant

Fees for Vendor appointed MEP consultant for jobs of Electrical, HVAC, IBMS, Fire Fighting, plumbing, etc. for services as per BOQ attached

Fees for Vendor appointed GRIHA/ IGBC consultant for 5-star rating of the Building

Fees for Vendor appointed MoEF consultant

Fees for Vendor appointed Structural/ Data cabling consultant

Fees for vendor appointed remaining services other than above mentioned as per BOQ

Liasoning charges for below approvals, the necessary statuary charges will be paid by the department

Municipal plan approval, Completion cum occupancy certificate (JoDA / JoMC) approvals

Fire & Sewarage: JoMC

Electrical Inspector, Government of Rajasthan

Public Health and Engineering Department for Water supply &water Test report

Airport authority

Environmental Clearance from Pollution control Board, Rajasthan

Ministry of Home Affairs

Electrical Load clearance from JdVVNL

Description of Work / Item(s)

Amount

Annual maintenance charges for following services as per the installation carried out by the bidder at the time of sign off and details of which is given in BOQ for following service s including all spares and consumables . The period will be counted after two years of Guarantee Period . ( for Two years after signing off the maintenance will be in scope of Contractor without any charges to Department ) 1.Comfort Air conditioning and ventilation 2.Elevators 3.IBMS including CCTV , Fire Detection , Fire suppression, Access control 4.Fire Hydrent and Fire Sprinkler services 4.DG Sets and HSD Tanks . 6 Transformers and HT panels , RMU , HT cables 7. All types of LT Cables and panels , Outdoor panels and all internal Electrical , Earthings jobs described in BOQ . 8 UPS and LAN Services 9.interior &Furniture 11.Civil and Plumbing services , WTP , STP , RO Water landscape 12 Solar 13 Audio & video , Auditorium articles , 14 All other items installed by bidder FOR Digital fintech university as mentioned in BoQ 1-16

1 st Year after completion of 2 years of Guarantee Period from date of signing off

2 nd Year after completion of 2 years of Guarantee Period from date of signing off

3 rd Year after completion of 2 years of Guarantee Period from date of signing off

Annual Operation charges for following services as per the installation carried out by the bidder at the time of sign off and details of which is given in BOQ for following service s. As per the final measured quantities . The period will be counted after signing off . The details of Manpower required is given in Technical specifications . The maintenance should be carried out by the maintance schedules and maintenance manual given by OEM and original manufacturar of the items installed. The details of manpower required during Operation & Maintenance is given in RFP 1.Comfort Air conditioning and ventilation 2.Elevators 3.IBMS including CCTV , Fire Detection , Fire suppression, Access control 4.Fire Hydrent and Fire Sprinkler services 4.DG Sets and HSD Tanks . 6 Transformers and HT panels , RMU , HT cables 7. All types of LT Cables and panels , Outdoor panels and all internal Electrical , Earthings jobs described in BOQ . 8 UPS and LAN Services 9.interior &Furniture 11.Civil and Plumbing services , WTP , STP , RO Water landscape 12 Solar 13 Audio & video , Auditorium articles , 14 All other items installed by bidder FOR Digital fintech university as mentioned in BoQ 1-17

1 st Year after signing off

2 nd Year after signing off

3 rd Year after signing off

4 th Year after signing off

5 th Year after signing off

Description of Work / Item(s)

Amount

Providing, fixing, testing and commissioning of white vitreous china wall mounted type European water closet with C.P. bolts, nuts, C.I. chair (painted with two coats of enamel paint over a coat of primer) or other hanging arrangements, built-in exposed white vitreous china low volume compatiable cistern with C.P. bolts, nuts, supporting arrangements, bakelite / poly propylene seat & cover with C.P. hinges & rubber buffers, complete with all accessories. Including cutting & making good the walls & floors wherever required.

Providing, fixing, testing & commissioning of concealed type cistern(low flow as per ECBC) with dual flush facility comprising of actuator button facia assembly including brass / SS screws and washer complete, providing protection cover over cistern, cutting and making good the walls wherever required.

Providing & fixing C.P brass toilet paper holder with PVC rawl plug & C.P. brass screw complete as required.

Providing, fixing, testing and commissioning of 15 mm dia C.P. brass 2 way cock with C.P. wall flange of approved quality and making good as required.

Providing, fixing, testing and commissionin Hand shower(Helth faucet) with 8 mm dia 1 mt long PVC tube &wall hook complete

Providing, fixing, Twin Coat hook

Providing, fixing, testing & commissioning of viterous china Indian type (Orissa pattern) water closet set in cement concrete 1:2:4 mix (1 cement: 2 coarse sand : 4 stone agrregate 20 mm nominal size) with 100 mm dia C.I. deep seal trap including cutting and making good the wall & floors complete as required.

Providing, fixing, testing and commissioning of exposed plastic low level cistern for WC, with dual flush facilit,y complete with all necessary fittings, flush pipes & accessories including all supports and making good.

Providing & fixing first quality white vitreous china oval / round / square wash basin (size as per architectural drawing) for under counter mounting, specially fabricated CI / MS brackets, painted with two or three coats of enamel paint of approved shade over a coat of primer, 32 mm CP brass waste and CP brass cast bottle trap and pipe to wall with CP brass flange and rubber adopter for waste connection complete including filling gap between counter and wash basin with approved type poly sulphide sealant, cutting and making good the walls wherever required.

Providing, fixing, testing and commissioning of Basin Mixture

Providing, fixing, testing and commissioning of C.P. brass angle valve with C.P. wall flange, Nut and Washer etc. complete as required.

Providing, Fixing, testing and commissioning of Single Lever Concealed Divertor/ Hot & Cold Mixer for Bath & Shower System along with Bath Spout with flange and Overhead Shower with revolving joint and 150 mm long shower arm with flange etc. complete as per direction.

15mm Bib Cock long body

Providing, Fixing, testing and commissioning of Single Lever Concealed L BAND MIXER FULL TURN/ Hot & Cold Mixer for Bath & Shower System along with Bath Spout with flange and Overhead Shower with revolving joint and 150 mm long shower arm with flange etc. complete as per direction.

Providing, fixing, testing and commissioning of white viterous china large flat back / half stall urinal supported by CI / MS bracket (duly painted with 2 coats of paints over a coat of primer), including CP brass waste with dome type grating, CP cast brass bottle trap with extension piece, wall flanges complete with all accessories.

Providing, fixing, testing and commissioning of white vitreous china large urinal partition with concealed CI bracket, cutting and making good.

Providing, fixing, testing and commissioning of automatic flushing systems for urinal to ensure pre-flush & flushing only immediately after use, comprising of all plumbing, electronic and electrical items. CP brass flush pipe with CP brass elbow, CP brass spreader, CP wall flange, infrared photo cells, eyes electrically operated solenoid valve, step down transformer / equipment and any other item required to provide satisfactory functioning. Including necessary wall cutting / chasing and making good, as required.

Providing, fixing, testing and commissioning of sink supported by C.I./M.S. Brackets (duly painted with 2 coats of paint over a coat of primer) C.P. cast brass bottle trap with extension piece, rubber adaptor, wall flange, union, C.P. brass chainrubber plug & making good.

2. Stainless steel sink with drain board.

Providing, fixing, testing and commissioning of C.P. brass wall / counter mounted sink mixer with C.P. wall flange, overhead swinging spout complete as required and making good.

Providing & fixing storage type water heater of approved shade with copper container, glasswool insulation,stove enamelled M.S jacket, thermostatically controlled inner heater with pilot neon lamps, angle valve on inlet connection, 15mm dia C.P flexible connection pipe in inlet & outlet suitable for working pressure of 5 kg/sqcm complete as required.

Capacity 15 litres

Capacity 25 litres

Providing & fixing storage type water cooler of the following capacity, I.S.I marked, stainless steel front panel, C.P brass push cock, inlet float valve with all plumbing and electrical accessories, inlet, outlet, overflow and PVC drain out connection to F.D complete as required.

Cooling capacity 15 Lts./hr Having Storage capacity of 40 Lts.

Cooling capacity 40 Lts./hr Having Storage capacity of 80 Lts.

Providing & fixing commercial water purifier of water flow rate 2.0 Lit/min. Including all components as per manufacture specifications, including connection from water supply line, and final connection to water cooler electric wiring & plug top etc. with all accessories.

Providing and fixing solid state, no touch operting, fully hygienic hand drier of approved shade with single blower, with time delay, summer & winter control, music while drying, volume ON/OFF controls including providing necessary brackets, cable from drier to Plug, Plug top key and lock etc, complete as required.

Providing & fixing C.P. brass towel rail with C.P. brass wall brackets & C.P brass screws complete as required of size below.

Size 600 x 20 mm size

Providing & fixing C.P. brass Towel ring

Providing & fixing Recessed type S.S. soap dish with PVC rawl plug & C.P. brass screw complete as required.

Providing & fixing C.P. brass liquid soap container with PVC rawl plug & C.P. brass screw complete as required.

Providing & fixing C.P brass deodourizer.

Providing, fixing, testing and commissioning of 15 mm dia C.P. brass bib cock with C.P. wall flange of approved quality and making good as required.

Providing, fixing, testing and commissioning of C.P. brass angle valve with C.P. wall flange, Nut and Washer etc. complete as required.

Providing, fixing, testing and commissioning of C.P Copper connection 375 mm long including nuts and washers and making connection to fixtures and fittings complete as required.

Providing, fixing, testing and commissioning of pillar cock with wall flange (as required) and making good as required.

Providing and fixing 35 mm dia powder coated steel grab bar.

B. COLD WATER SUPPLY : (INTERNAL / EXTERNAL)

Providing and fixing CPVC (Chlorinated Poly Vinyl Chloride) water supply pipes with pipe as per CTS SDR 11 (operating pressure - 7 Bar @ 82 Deg C and 28 Bar @ 23 Deg C)for pipes from 1/2 Inch to 2 Inch. Schedule 80 Pipe to be used from 2-1/2 Inch to 6 Inch. Pipes shall be joined using solvent welded CPVC fittings i.e. Tees, Elbows, Couplers, Unions, Reducers, brushings etc. including transition fittings (connection between CPVC & metal pipe/GI) i.e. Brass Adaptors (both Male & Female threaded) conforming to ASTM D-2846. ASTM F441 with only CPVC solvent cement conforming to ASTM F-493. All termination points for installation of faucets shall have brass termination fittings. Installation shall be to as per Technical Manual of manufacturer of pipes & fittings.(All Terrace Looping sch80 & sdr11 for Internal Toilet)

Cost shall be inclusive of (a)Making maximum of 7.5 x 7.5 cm chase in wall and floors for the pipe, making good the same by using 1:2 cement mortar over the wire mesh and providing protection to embedded pipes and fittings (in wall chase) by wrapping two layers of 400 micron polythene sheet including proper overlaps on joints complete as required or (b) Fixing/supporting the pipes (& fittings) at wall/ceiling level supported by galvanized clamps, fastener, hangers etc, as per specification. Exposed pipes to be painted of legends with direction arrow. GI pipe sleeves suitable higher size shall be provided wherever the pipes are crossing the fire rated walls / floors slab and sealing the sleeves with glass wool in between and fire sealant compound at either end all as per Project Manager's / Consultant requirement.

3/4" dia (20 mm)

1" dia (25 mm)

1.1/4" dia (32 mm)

1.1/2: dia (40 mm)

2" dia (50 mm)

2.1/2" dia (65 mm)

3" dia (80 mm)

4" dia (100 mm)

Providing ,fixing,laying of hot water pipe insulation with tubolit closed cell polyethylene pipe insulation sleeve of approved make of 6mm thickness concealed in toilets and Shaft.

For 20mm CPVC PIPE

For 25mm CPVC PIPE

For 32mm CPVC PIPE

For 40mm CPVC PIPE

For 50mm CPVC PIPE

For 65mm CPVC PIPE

For 80mm CPVC PIPE

Providing & fixing brass conceald stop cock body(as per approved specification)

20 mm dia

Providing & fixing male/ female screwed end full way lever operated forged brass ball valve of brass body with forged brass hard chromeplated ball & teflon seat tested to a pressure 30 Kg / sqcm with (threaded joints) complete as required.

20 mm dia

25 mm dia

32 mm dia

40 mm dia

50 mm dia

Providing and fixing C.I. Butterfly valve (Body : Grey Cast Iron, shaft : SS, Disc : SG Iron (nickel plated), Liner : HT - EPDM) of approved make with flange, washer, nuts & bolts and PN 10/16 pressure rating including rubber gasket & painting complete.(Plant Room + OHT Etc)

65 mm dia

80 mm dia

100 mm dia

150 mm dia

Providing & fixing screwed ended gun metal horizontal / vertical non return valve conforming to IS 778 Class II and of PN 16 pressure rating including rubber gasket, union, etc. complete as required.(Plant Room)

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

Providing & fixing dual flanged C.I. `Y' Strainer with stainless steel fine wire mesh perforated sheet basket with necessary flange/ unions nuts, bolts and washers complete as required.

40 mm dia

50 mm dia

65 mm dia

80 mm dia

100 mm dia

150 mm dia

Providing and fixing in position of approved quality high pressure rated Gun Metal Float Valve with copper ball float and brass rods of required length suitable for test pressure of not less than 15 Kg/sqcm of the following sizes:

40 mm dia

50 mm dia

Providing and fixing pressure reducing station for cold water supply comprising of 2 Nos Gun Metal ball valves on inlet & outlet & 1 no. globe valve for by-pass 1 No pressure reducing valve with flanged/ screwed connection, 1 No. `Y' strainer, 2 Nos Pressure gauge on inlet & outlet, and 1 No. 15 mm dia safety valve. The complete system is tested to a pressure not less than 15 Kg/Sq.cm and suitable to reduce the pressure upto 2 Kg/Sq.cm) Including necessary pipe & fittings; i.e. flanges/ unions, nuts, bolts and washers complete as required.

50 mm dia (CI Housing - PRV)

65 mm dia (CI Housing - PRV)

Providing, fixing , testing and commissioning water meter with direct reading dial in KL with all necessary fitting such as threaded pieces, unions pressure gauge, isolation cock, flanges piece for future removal, flanges / unions complete with all necessary testing charges and obtaining test certificates from municipal authorities, on following size pipe lines (1 no. strainer shall be provided at inlet & outlet and cost shall be inclusive for the same). The meter shall comply to ISO 4064 standard, feasible for class B or Class A installation.

40 mm dia (Gun metal)

50 mm dia (Gun metal)

65 mm dia (CI)

Providing & fixing on line turbine type flow meter with preamplifier & microprocessor based electronic flow meter mounted in plumbing plant room electrical control panel with the following features. Monitoring the total flow, Flow rate, high low arm batching and blending etc. Including electrical wiring from preamplifier to microprocessor based flow meter. Complete with all type of Plumbing & Electrical connections, accessories, wiring, conduits & supports complete with all respect. The signal from read out shall be 4-20 m.amps to be received on BAS.

80 mm dia

Making water supply connection to kitchen / laundry(Common area) equipment, appliances, coolers etc. including necessary fittings, (pipes and valves to be paid separately).

15 mm to 25 mm dia

32 mm to 50 mm dia

Providing & fixing Auto Air vent for cold water supply risers, suitable for pressure not less than 15 Kg/Sq.cm.

20 mm dia

Providing and fixing 600 mm dia ductile iron (heavy duty) water tank circular cover with frame (as per EN-124) with lockable arrangement complete in all regards (Total WT of cover and frame tobe not less than 85 kg).

Providing & fixing in position 25 mm dia lawn hydrants consisting of 25 mm dia Ball valve, GI nipple and quick release coupling / threaded hose receiver complete as required.

Constructing brick masonary chamber (for housing valves, Meters etc.) of brick work with bricks of class 75 with cement mortar 1:5 (1 cement:5 fine sand) plastering internal face & (with a floating coat of neat cement) cement mortar 1:3 (1 cement: 3 fine sand and rough plaster on outer face. R.C.C top slab with medium duty D.I. manhole cover and frame of 600 mm dia (weight : 60 KG). Including excavation, dewatering, refilling, watering, ramming and removing the surplus excavated material complete as required. (All sizes are clear internal sizes).

Size 600x 600 x 600 mm deep (with 600 x 600 MD; DI cover (Wt : 45 kg))

INTERNAL DRAINAGE : SOIL, WASTE , VENT AND RAIN WATER PIPES WITH FITTINGS

Providing, fixing & testing uPVC SWR pipes confirming to IS 13592 (Type B 6KG/CM2) alongwith all required fittings like tees, bends, crosses with or without access doors jointed with approved solvent cement as per manufacturer's recommendations, fixed to walls and ceilings with clamps complete including cutting and making good the floors and walls where required complete of outer diameter.

75 mm Dia

110mm Dia

160mm Dia

Providing, fixing, jointing, testing and commissioning of UPVC pipe onfirming to IS : 13592 Type A 4kg/cm2, cut to required lengths including all necessary fittings and specials such as bends, junctions offsets, access pieces (plain or door) & vent cowl. Fixing at wall / ceiling level supported by G.I. clamps, hangers etc. duly epoxy coated. (Vent Stack )

75 mm dia

Providing, fixing, jointing, testing and commissioning of UPVC pipe confirming to IS : 4985 (Pipe Class III - 6 kg / sq.cm) cut to required lengths including all necessary fittings and specials such as bends, junctions offsets, access pieces (plain or door) & vent cowl. Fixing at wall / ceiling level supported by G.I. clamps, hangers etc. duly epoxy coated.(Internal Soil Waste Vent connection)

40 mm dia

50 mm dia

Providing and fixing in position 75 mm UPVC Nahni traps/Multifloor traps Trapning design including 125 mm dia UPVC grating, joining, embedding in concrete etc. complete rate to include making of opening in floor, marble / tiles, for fixing grating.

Providing, fixing and testing of uPVC SWR P or S trap including jointing with solvent cement and making good the walls, floors etc., complete of nominal size.

Providing, fixing and testing of uPVC SWR inlet fittings / Height riser with two or three saddle inlets of 40, 50 mm size, fabricated from 110 mm outer dia uPVC pipes and fixed to uPVC traps with drip seal/m-seal/solvent cement joint complete in all respect.

Providing and fixing PVC floor drain for balcony 100 x 50mm, complete as per instructions of the Engineer in charge.

Providing and fixing Multi Floor trap 75MM Outlet /3 inlet 125mm Height , complete as per instructions of the Engineer in charge.

Providing and fixing Heavy class SS grating with Cockroach proof SS strainer of approved design including setting in floor with cement motor to match with floor finish as per architect requirement & suitable for waste and FD.

Size 150 mm x 150 mm or 125 mm dia

Providing and fixing PVC clean out plug & Fittings

For 110 mm dia pipe (Straight type/door bend )

For 150 mm dia pipe (Straight type/door bend)

Providing and fixing P.V.C. WC connector (straight or bend type) with rubber lip ring. Including 110 mm dia PVC pipe / bend of required length and proper connection.

Making drainage connection to kitchen / laundry (Common area) equipment, appliances etc. including necessary GI pipes / fittings & Flexiable pipes complete as required.

32 mm dia to 50 mm dia

Providing & fixing rain water `Khurras' size 450x450 mm required depth with lead flashing around the pipe with one piece lead sheet of 3 mm thick set on a layer of cold bitumen. Including Heavy duty CI/MS grating as per drawing complete as required.

Providing and fixing CI rain water head of required length with puddle flange to fix head in RCC slab including removable heavy duty dome type CI grating and CI hopper of approved design.

260 mm dia ; 100 mm outlet

400 mm dia; 150 mm outlet

Providing and fixing square mouth cast iron gully trap complete with CI grating in brick masonry chamber of standard detail with first class bricks and water tight double seal CI cover with frame of 300 x 300 mm internal size. The weight of cover and frame to be not less than 10 Kg as per standard design.

(Note : Cost shall include excavation dewatering and watering proofing of chambers as directed at site)

450 x 450 mm chamber with 150 x 150 mm size “P” trap

Constructing Grease Trap of size as mentioned below of 1200 liquid depth in brick work of class 75 with cement mortar (1:6), inside plastering 16 mm thick with cement mortar 1:3 with floating coat ofneat cement and rough plaster on outside. Including aluminium bucket as per detail to collect the grease. RCC top slab with 2 nos. 600 x 600 mm dia medium duty, double seal manhole covers with frame (weight of covers & weight of frame 75 Kg), necessary 150 mm thick foundation concrete (1:2:4).

EXTERNAL SEWAGE / STORM WATER DRAINAGE:

Providing, fixing, jointing and testing in position the following UPVC pipes confirming to IS:4985 of 6 Kg / Sq.cm for drainage system cut to required length. Pipe to be laid below ground level in trenches upto required depth including excavation in all kind of soil (hard rock), dewatering, refilling, watering, ramming and removing the surplus excavated material and making good the same complete as required. Cost shall be inclusive of providing protection to pipe all round / haunches as per specification.

110 mm dia

160mm Dia

Providing , Fixing, testing and commissioning and laying UPVC Foamcore Class-SN-8 pipes, including testing of pipes and joints etc. complete with the necessary excavation, providing and laying PCC (1:4:8), laying, refilling, compaction, dewatering, curing, retesting and disposal of any excess earth/soil from the site. The pipes shall be of following nominal bore (NB) size: External sewage water

160 mm dia

200 mm dia

250 mm dia

300 mm dia

Laying, jointing and testing socketed and spigotted RCC pipes (NP2 class) conforming to IS:458 collars jointed with stiff mixture of cement mortar in the proporation of 1:2 (1 cement : 2 find sand) laid to correct levels below ground in trenches upto required depth including excavation in all kind of soil (hard / soft), dewatering, refilling, watering, ramming and removing the surplus excavated material and making good the same complete as required. Cost shall be inclusive of providing protection to pipe all round / haunches as per specification. External storm water

200 mm dia

250 mm dia

300 mm dia

400 mm dia

Providing and fixing 600 mm long MS hot dip galvanized PUDDLE FLANGES fabricated out of 6 mm thick MS plates of suitable size and IS:1239 heavy class pipes properly fixed in walls & top slab of tanks. The entire fittings shall be hot dipped galvanized after fabrication. Length shall be minimum 600 mm or wall thickness plus 200 mm on either side (which ever is more).

32 mm dia (screwed ends)

40 mm dia (screwed ends)

50 mm dia (flanged ends)

65 mm dia (flanged ends)

80 mm dia (flanged ends)

100 mm dia (flanged ends)

150 mm dia (flanged ends)

200 mm dia (flanged ends)

250 mm dia (flanged ends)

Providing and fixing blank flanges, making flanged joints with bolts, nuts, washers and rubber insertion 3 mm thick, testing the flange and joints etc. complete for pipes of following diameter.

25 mm dia

50 mm dia

65 mm dia

80 mm dia

100 mm dia

150 mm dia

200 mm dia

Providing and fixing in position the Mild Steel (MS) ‘C’ class pipes as SLEEVES each to be embedded in RCC walls / beams.

250 mm dia (800 mm long)

200 mm dia (600 mm long)

150 mm dia (600 mm long)

100 mm dia (600 mm long)

75 mm dia (600 mm long)

50 mm dia (600 mm long)

Providing, laying, jointing and testing in position the following heavy class GI pipes for under ground piping conforming to IS:1239 including all necessary fittings (conforming to IS : 1879) such as elbow, coupler & tee etc. Cost shall be inclusive of excavation, dewatering, backfilling, ramming surrounding the pipe all round with minimum 150 mm thick all round compacted silver sand and providing thrust block. (Pipe shall be provided with anti crossive protective treatment Pypkote / Coatek confirming to AWWA C 203 / IS 10221 standard complete as per specification). All work complete as per specification and satisfaction of the Project Manager.

80 mm dia

100MM Dia

150 MM Dia

Providing & Fixing Bevelled edge Mirror/mirror with teak wood lipping around of special glass of approved make as per direction of Engineer-in-charge complete with 6mm thick commercial ply base fixed to wooden screws & washers.

Description of Work / Item(s)

Amount

S&F following sizes (dia.) of ISI marked MMS ( IS:9537 P - III )vergin material PVC conduit as per PWD specification for electrical Works along with its accessories (IS: 3419 ) as required in recess including cutting the wall, covering conduit and making good the same as required. All relative and latest acceptance tests reports by any NABL accredited lab for the conduit shall be submitted before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

Wiring of light point/ fan point/ exhaust fan point/ call bell point as per PWD specification for electrical Works with ISI marked 1.5 sq. mm nominal size FRLS PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694) and 1.5 sq. mm nominal size FRLS PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) vergin material PVC conduit & it's all accessories( J.B. , Bends etc.) , round tiles,18 SWG Hot Dipped Galvanized Modular Box with earth terminal, 6 A Modular switch, Modular face plate with grid plate, 3 pin ceiling rose / lamp Holder/ 3 pin connector , screws etc, making connections,all as per pre approved by Engineer in charge, testing etc. complete as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 . F

Short point (up to 3 mtr.)

Medium point (up to 6 mtr.)

Long point (up to 10 mtr..)

Wiring of twin control light point as per PWD specification for electrical Works with ISI marked 1.5 sq. mm nominal size FRLS PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694) and 1.5 sq. mm nominal size FRLS PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) vergin material PVC conduit & it's all accessories( J.B. , Bends etc.) , round tiles,2 nos. 18 SWG Hot Dipped Galvanized Modular Box with earth terminal,2 Nos 6 A two way Modular switch, 3 pin ceiling rose / lamp holder/ 3 pin connector ,Modular face plate with grid plate, screws etc,all as per pre approved by Engineer in charge, making connections, testing etc. complete as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

Medium point (up to 6 mtr.)

Long point (up to 10 mtr..)

Wiring of 3/5 pin 6 amp. Universal type Light plug point as per PWD specification for electrical Works with ISI marked 1.5 sq. mm nominal size FRLS PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694) and 1.5 sq. mm nominal size FRLS PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) vergin material PVC conduit & it's all accessories( J.B. , Bends etc.) , round tiles, 18 SWG Hot Dipped Galvanized Modular Box with earth terminal, 6 A modular switch, 3/ 5 pin 6 A modular socket, Modular face plate with grid plate, screws etc,all as per pre approved by Engineer in charge, making connections, testing etc. complete as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05

On board

S&F following sizes (dia.) of ISI marked ( IS:9537 P - II ) rigid steel conduit of apropriate thickness related to its dia as per PWD specification for electrical Works along with accessories in recessed using saddles, clamps, fasteners, pvc bushes, check nuts, screwas etc. as required including cutting the wall and making good the same as required all as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

Supplying and drawing FRLS PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.99% purity copper, class 5 stranding in acc. to IEC 60228 for lower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation PVC type A ,flame retardant as per IS 10810-53, better amperage rating as per VDE 0298 part 4, , in existing surface or recessed PVC/ MS conduit/casing capping including all as per pre approved by Engineer in charge,making connections, etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

2x 1.5 sq.mm

3x 1.5 sq.mm

2 x 2.5 sq. mm. + 1x1.5sqmm

3 x 2.5 sq.mm

4 x 2.5 sq.mm

2 x 4.0 sq. mm. + 1 x 2.5 sq. mm.

2 x 6.0 sq. mm. + 1 x 2.5 sq. mm.

1 x 4.0 sq.mm

4 x 6.0 sq.mm

4 x 10.0 sq.mm

1 x 6.0 sq.mm

Providing & Fixing of phenolic laminated sheet 2.0 mm thick of following size . Including screws, cup washer as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

100 mm dia.

P & F 18 swg M.S. Recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mm length extended on each side . All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

Providing & Fixing of 240/415 V AC MCB with positive isolation of breaking capacity not less than 10 KA (B/ C tripping characteristic as per type of load and site requirement) 4KV impulse withstand voltage, as per PWD specification for electrical Works with ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductorline load reversibility, label holding facility , IP 20 contact protection and fitted with existing distribution board/sheets, min. operation 20,000 upto 32 A rating and 10,000 upto 63 A, 5000 for 80 A rating including making connections, testing etc. as required. . OEM shall have submit NABL / CPRI / ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

Single pole MCB

6 A to 32 A rating

Double pole MCB

40 A rating

50-63 A rating

Triple pole MCB

6 A to 32 A rating

40 A rating

50-63 A rating

Four pole MCB

6 A to 32 A rating

40 A rating

50-63 A rating

80 A rating

Providing & Fixing of 240/415 V factory fitted RCBO with overload, short-circuit and earth leakage protection as per PWD specification for electrical Works with ISI marked (IS12640-2)/ conforming to IEC 61009-1, breaking capacity 10 KA, true position indication and trip free mechanisum, line load reversibility, provision for pad lock, min. operation 10,000 upto 63 A rating and 5000 for 80 A-100 A rating, minimum phase termination capacity of 35sq.mm. , IP 20 contact protection with existing distribution board / sheet including making connections, testing etc. as required.OEM shall have submit NABL / CPRI / ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

Two pole 30 mA sensitivity

6A-32 A rating

40 A rating

Four pole 30 mA sensitivity

63 A rating

Providing & Fixing of 240/415 V Residual current circuit breaker (RCCB) as per PWD specification for electrical Works with ISI marked (IS:12640-1) / conforming to IEC 61008 -1 , rated conditional s/c current of 10 KA, truly current operated and shall operate on CBCT mechanisum, provision for pad lock, min. operation 10,000 upto 63 A rating and 5000 for 100 A rating, minimum phase termination capacity of 50 sq.mm. rigid wire , IP 20 contact protection with existing distribution board / sheet including making connections, testing etc. as required.OEM shall have submit NABL / CPRI / ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

Two pole 30 mA sensitivity

16/25 A rating

32/40 A rating

63 A rating

Four pole 30 mA sensitivity

63 A rating

Four pole 100/300 mA sensitivity

63 A rating

Providing & Fixing of IK09 recessed/surface mounting heavy duty horizontal type sheet steel of 1.6 mm thick Distribution board as per PWD specification for electrical Works ISI marked conforming to IS-13032 & IS-8623 / conforming to IEC 61439-3. Phosphatised/ powder painted complete with suitable rating insulated copper bus bar, shorting link , neutral link, earth link , connecting wire of suitable rating and din bar,masking sheet, including making internal DB terminations with copper lugs and with detachable gland plate, including making connections, testing etc. as required.OEM shall have submit NABL / CPRI/ ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure"A" Rajasthan PWD BSR 2021.

IP-43 Double door (single phase)

6 Way (6 O/G +2 I/C )

IP-43 Double door (Three phase)

4 Way ( 12 O/G + 8 I/C )

6 Way ( 18 O/G + 8 I/C )

8 Way ( 24 O/G + 8 I/C )

12 Way ( 36 O/G + 8 I/C )

Providing & Fixing of IK 09 recessed/surface mounting heavy duty Flexi/Row TPN sheet steel 1.6 mm thick Distribution board as per PWD specification for electrical Works ISI marked conforming to IS-13032 & IS-8623/conforming to IEC 61439-3.Phosphatised/ powder painted complete with suitable rating insulated copper bus bar, shorting link , neutral link, earth link and din bar,masking sheet, including making internal DB terminations with copper lugs and with detachable gland plate, testing etc. as required complete in all respect.OEM shall have submit NABL / CPRI / ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

IP-43 Double door

2 Row 28 Module(14 module per row)

3 Row 42 Module(14 module per row)

4 Row 56 Module(14 module per row)

Providing & Fixing of recessed/surface mounting type sheet steel / Plastic enclosure as per PWD specification for electrical Works conforming to IEC 61439-3 of 1.6 mm thick for housing MCB/Isolator with Din rail including , all as per pre approved by Engineer in charge,making connections, with lugs, repairs etc. as required.OEM shall have submit NABL / CPRI / ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

With sheet steel enclosure

Two way

Four way

Providing & Fixing of metal clad industrial plug top & socket unit with pin and sleeve type copper contact on porcelain/ bakelite base insheet steel( CRCA ) powed coated enclosure as per PWD specification for electrical Works conforming to Is 8623 & IEC 61439-3 (without MCB) including , all as per pre approved by Engineer in charge,making connections,, testing etc.as required .OEM shall have submit NABL / CPRI / ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

20 A Double Pole (single phase Three pin )

Providing & Fixing of Industrial plug and socket as per PWD specification for electrical Works conforming to IEC 60309- 1/2 made out of self extinguishing engineering polymer / polyamide, nickel plated brass sleeve and pins, socket with shutter including making connection etc as reqd complete in all respect.OEM shall have submit NABL / CPRI / ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

Surface/Wall mounted socket

32 A 5 pin(3P+N+E)

Plug top

32 A 5 pin(3P+N+E)

Providing & Fixing of IK 09 rating recessed/surface mounting heavy duty Vertical type sheet steel 1.6 mm thick Distribution board as per PWD specification for electrical Works ISI marked conforming to IS-13032 & IS-8623 / conforming to IEC 61439-3 with provision of incomer suitable for MCCB and SP / TP MCB as outgoing , phosphatised ,powder painted complete with insulated suitable rating copper bus bar , neutral link, earth link and din bar, masking sheet, including making internal DB terminations with copper lugs and with detachable gland plate, testing etc. as required complete in all respect.OEM shall have submit NABL / CPRI / ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

IP 43- Double door with Provision of Incomer MCCB 100 / 125/160 A Rating

Providing & Fixing of recessed/surface mounting heavy duty sheet steel 1.6 mm thick End Box as per PWD specification for electrical Works for distribution board duly phophatised powder coated complete as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

For TPN 4 way DB

For TPN 6 way DB

For TPN 8 way DB

For TPN 12 way DB

For all VTPN DB

Providing & Fixing of modular type switch/ bell push duly ISI marked (IS :3854) as per PWD specification for electrical Works, made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating , minimum width of 1 module switch toggle( PUSH PART ) should not less then 20mm, including all as per pre approved by Engineer in charge,making connections, testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

6 A bell push

Providing & Fixing of modular type Step Fan regulator duly ISI marked (IS :11037) as per PWD specification for electrical Works, made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating , minimum width of 1 module switch toggle( PUSH PART ) should not less then 20mm, including all as per pre approved by Engineer in charge,making connections, testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

5 step fan regulator 100 watt 2 Module

Supplying and fixing of power plug point with Modular accessories as per PWD specification for electrical Works, on hot dipped galvanized modular box of 18 SWG with earthing terminal/connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost of ISI marked modular 16 amp. Switch (IS :3854) and 3/5 pin 16 amp. socket outlet (IS:1293) [ as per detailed in respective item in BSR] , making connection , testing , etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

Providing & Fixing of ISO certified company made vergin material PVC trunking system as per PWD specification for electrical Works, with double lock feature for cable management including finishing accessories like corners, tee, adjustable angles, junction etc. as required . The trunking system shall have adaptable system for modular type RJ 45 data socket/ wiring accessories/ power sockets and shall be covered with peal off plastic cover. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

100/105mm x 50mm

Providing & Fixing of following size hot dip galvanized M.S. box of 18 SWG as per PWD specification for electrical Works, with earthing terminal in recess/ surface suitable for modular accessories as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

1-2 Module

SITC of Draw out type 3/4 pole IP53, IK 08 door interlock Air Circuit Breaker (ACB) as per PWD specification for electrical Works, conforming to IS/IEC 60947 P - 2 :2003 in existing LT panel suitable for LT installation 440 V, 50 Hz and having adjustable over load short-circuit, earth fault and with separate LED indication for each type of fault , Password protected relase (trip mechanisum) shall confirm to EMI/ EMC test , LCD/LED display , Thermal memory , pollution degree 4, trip free mechanisum , suitable for ambient 50 degree and utilization catagary B. In built electrical & mechanical anti pumping fearute , 100% rated neutral . ACB shall have separate indication for service, test, isolation & maintenance position, Breaking capacity Icu = Ics = Icw ( 1 sec ) , U imp - 12 KV, break time not more then 25 ms. Provision for electrical & mechanical interlock between ACBs, Min.electrical operation 10,000 upto 2000 A rating and 5,000 for 2500 A. including making connections etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test certificate before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

Microprocessor based release Draw out type (Manual spring charged) 4Pole

800 A Rating , 50kA

1000 A Rating , 50kA

1250 A Rating ,50kA

Supply and fixing of following accessories for Air circuit breaker (ACB) compatible with MAin ACB OEM as per PWD specification for electrical Works, conforming to IS/IEC 60947 P - 2 :2003 including making connection etc complete in all respect. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test certificate before execution . All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

Shunt Trip Release

Under Voltage Release

SITC of IP 40 quick make and quick break 4 pole current limiting Moulded case circuit breaker (MCCB) made of flame retardent & heat resistant material having following current rating, short circuit breaking capacity at 440/415 V, 50 Hz; O/L & S/C settings as per PWD specification for electrical Works, conforming to IS/IEC 60947 P -2 :2003 with front face and centralised adjustable, trip free mechanisum, true contact position indicator, line load interchangeability, designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation upto 55 degree and without derating upto 40 degree, pollution degree 3, having positive isolation capability, push (test) to trip, trip time less then 10 ms under s/c condition, Breaking capacity Ics = 100% Icu. U imp =8 KV, rated insulation voltage 800 V, provision for UVR , shunt trip , earth fault trip, door interlock, pad lock & rotary handle , including making connections with lugs & spreaders, etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test certificate before execution. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

With Thermal Magnetic release

up to 100 Amp , 25 kA, adjustable O/L & fixed S/C setting, Ics = 100 % Icu

125 Amp , 25 kA, adjustable O/L & fixed S/C setting, Ics = 100 % Icu

160 Amp, 25 kA, adjustable O/L & fixed S/C setting, Ics = 100 % Icu

200 Amp , 35kA, adjustable O/L & fixed S/C setting, Ics = 100 % Icu

250 Amp , 35 kA, adjustable O/L & fixed S/C setting, Ics = 100 % Icu

400 Amp ,50 kA, adjustable O/L & adjustable S/C setting, Ics = 100 % Icu

630 Amp , 50 kA, adjustable O/L & adjustable S/C setting, Ics = 100 % Icu630 Amp , 50 kA, adjustable O/L & adjustable S/C setting, Ics= 100 % Icu

SITC of IP 40 3 pole current limiting Moulded case circuit breaker (MCCB) made of flame retardent & heat resistant material having following current rating, short circuit breaking capacity at 440/415 V, 50 Hz; O/L & S/C settings as per PWD specification for electrical Works, conforming to IS/IEC 60947 P -2 :2003 with front face and centralised adjustable, trip free mechanisum, true contact position indicator, line load interchangeability, designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation upto 55 degree and without derating upto 40 degree, pollution degree 3, having positive isolation capability, push (test) to trip, trip time less then 10 ms under s/c condition, Breaking capacity Ics = 100% Icu. U imp =8 KV, rated insulation voltage 800 V, provision for UVR , shunt trip , earth fault trip, door interlock, pad lock & rotary handle , including making connections with lugs & spreaders, etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test certificate before execution. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

With Thermal Magnetic release

up to 100 Amp , 25 kA, adjustable O/L & fixed S/C setting, Ics = 100 % Icu

125 Amp , 25 kA, adjustable O/L & fixed S/C setting, Ics = 100 % Icu

Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Un-armoured / Armoured aluminium cable of 1.1 KV grade as per PWD specification for electrical Works in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench with filling of excavated earth in trench , on existing cable trays or on surface etc. including making necessary connection, testing etc. as required of size and as per points (a), (b), (c), mentioned below:-(Note- All Cables are XLPE insulated and are armoured Alumunium Cables)

(a) Material :- H4- Grade aluminium conductor of purity >99.6 % & as per IS:1554 P-I / IS :7098 P - I

(b) conductor shall have electrolytic aluminium confirming to IS 8130, IS 3975-1999 for armouring of cables in armoured cable items , IS 5831 for sheath, IS 10810 (Part 0 to 64 ) for testing procedures .

(c) OEM Must have ISO 9001 & 14001 certifications for quality assuarance & its own in house NABL lab setup for all testing facilities for cables . Appropriate type test certificate / OEM test report shall be submitted . All above as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

Laying and fixing of PVC /XLPE power Cable of 1.1 KV grade of following size on wall/ cable tray with saddles/MS flat clamp etc as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021. (Note- All Cables are XLPE insulated and are armoured Alumunium Cables)

upto 35 sqmm

above 35 Sqmm and upto 95 sqmm

above 95 Sqmm and upto 185 sqmm

above 185 Sqmm and upto 300 sqmm

Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Un-armoured / Armoured copper cable of 1.1 KV grade as per PWD specification for electrical Works in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench with filling of excavated earth in trench , on existing cable trays or on surface etc. including making necessary connection, testing etc. as required of size and as per points (a), (b), (c), mentioned below:-

(a) Copper conductor of electrlytic grade copper, purity >99.97 % ISI marked as per IS:1554 P-I / IS :7098 P - I

(b) conductor shall made of copper rods confirming to IS 613-1964, IS 3975-1999 for armouring of cables in armoured cable items , IS 5831 for sheath, IS 10810 (Part 0 to 64 ) for testing procedures

(c) OEM Must have ISO 9001 & 14001 certifications & its own in house NABL lab setup for all testing facilities for cables . Appropriate type test certificate / OEM test report shall be submitted . All above as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

Un-Armoured

Armoured

Supplying and making one end termination with heavy duty brass compression gland (as per IS 12943- 1990) SIBG type, heavy duty aluminium lugs (as per IS 8309 - 1993 & IS 8337-1976 ) duly crimped with crimping tool, PVC tape as per PWD specification for electrical Works etc for following size of Armoured PVC insulated & PVC sheathed/ XLPE aluminium conductor cable of 1100 volt grade as required of size. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

3.5 x 35.0 sq.mm

3.5 x 50.0 sq.mm

3.5 x 70.0 sq.mm

3.5 x 120.0 sq.mm

3.5 x 150.0 sq.mm

3.5 x 185.0 sq.mm

3.5 x 240.0 sq.mm

3.5 x 300.0 sq.mm

3.5 x 400.0 sq.mm

4 x 10.0 sq.mm

4 x 16.0 sq.mm

4 x 25.0 sq.mm

Supplying and making one end termination with heavy duty single compression brass gland SIBG type, heavy duty Copper lugs duly crimped with crimping tool, PVC tape etc for following size of Armoured PVC insulated & PVC sheathed/ XLPE aluminium conductor cable of 1100 volt grade as required of size.

2 x 25.0 sq.mm

4 x 4.0 sq.mm

4 x 6.0 sq.mm

4 x 10.0 sq.mm

4 x 16.0 sq.mm

4 x 50.0 sq.mm

1X 70.0 Sq.mm

Supplying and making end termination with heavy Copper/ Bimetallic lugs Pin / ring type (IS 8337- 1976) duly crimped with crimping tool, PVC tape as per PWD specification for electrical Works etc of following size. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

Supply, Fabricating & installing following sizes of perforated Hot dipped Galvanized iron cable tray ( Galvanized thickness not less then 50 microns) with perforation not more then 17.5% in convenient section including horizontal and vertical bends, reducers tees,cross members and other accessories as required and duly suspended from the ceiling with GI suspenders including GI bolts & nuts , fastners, supports etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

100mm x 50mm x 1.6mm

150mm x 50mm x 1.6mm

225mm x 50mm x 1.6mm

300mm x 50mm x 1.6mm

450mm x 50mm x 2.0mm

600mm x 50mm x 2.0mm

Supply, Fabricating & installing following sizes of powder coated ladder type M.S. cable trays with rungs at span of 250 mm including horizontal and vertical bends, reducers tees,cross members and other accessories as required and duly suspended from the ceiling/wall with MS suspenders including bolts & nuts ,fastners, supports, painting suspenders etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

600mm x 50mm x 2.0mm

S/F cable route marker with 10cm x 10cm x 5mm thick or of 10cm dia. G.I.plate with inscription thereon, bolted/welded to 35mm x 35mm x 6mm angle iron,60cm long and fixing the same in ground in C C ( 1:3:6 ) as required.All as per pre approved by Engineer in charge. For additional technical parameters of products/work , refer Annexure "A" Rajasthan PWD BSR 2021.

Providing & laying of Double wall corrugated pipe confirming to IS : 14930 P - 1 & 2 with HDPE Coupler at 1 mtr. Depth below the ground for laying cable including making the trench and back filling , compaction of earth as required( Excavation of Earth to be paid Extra as required. ) of following Outer Dia. / Inner dia as per IS:4984:1995. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) etc. as required. ( Excavation of Earth to be paid Extra as required. ) All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

200 mm Dia.

250 mm dia.

300 mm dia

450 mm dia.

Supply & Laying following size earth strip in horizontal or vertical run in Ground/surface/recess including riveting, soldering, saddles, Jointing shall be done by overlapping and with 2 set of Brass (for Cu strip) / GI (for GI Strip) nut bolt & spring washer spaced at 50cm making connection etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

25mm x 3mm copper strip

25mm x 5mm copper strip

50mm x 6mm copper strip

25mm x 3mm G.I. ( Hot Dipped ) Strip

25mm x 6mm G.I. ( Hot Dipped ) Strip

50mm x 6mm G.I. ( Hot Dipped ) Strip

Supply & Laying following size earth wire in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection with GI/Cu thimble etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

8 SWG copper Wire

8 SWG G.I. ( Hot Dipped ) Wire

Plate Earthing as per PWD specification for electrical Works as per IS:3043 with Hot dipped G.I. Earth plate of size 600mm x 600mm x 6.0mm by embodying 3 to 4 mtr. below the ground level with 20 mm dia. G.I. 'B' class watering Pipe ,including all accessories like nut, bolts, reducer, nipple, wire meshed funnel, and Heavy duty weather proof poly-propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height 250 to 300 mm. and embodying the pipe complete with alternate layers salt and coke/ charcoal, testing of earth resistance for value of 5 ohms or less as required & must record by engineer in charge during site visit and ensure to enter in measurment book. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

Plate Earthing as per PWD specification for electrical Works as per IS:3043 with copper Earth plate of size 600mm x 600mm x 3.0mm by embodying 3 to 4 mtr. below the ground level with 20 mm dia. G.I. 'B' class watering Pipe ,including all accessories like nut, bolts, reducer, nipple, wire meshed funnel, and Heavy duty weather proof poly- propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height 250 to 300 mm. and embodying the pipe complete with alternate layers salt and coke/ charcoal, testing of earth resistance for value of 5 ohms or less as required & must record by engineer in charge during site visit and ensure to enter in measurment book. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

P & F of Heavy duty weather proof poly-propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height 250 to 300 mm. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

Providing & Fixing of ISO Certified company made BEE Star rated copper wounded double ball bearing capacitor start, aluminium body & Metallic blade ceiling fan as per PWD specification for electrical Works, conforming to IS:374-2019, & IS:1885 -P-V- 1981. with down rod up to 30 cm with secondary support safety cable ( steel wire ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. Appropriate OEM test certificate shall be submitted by contractor. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

1200 mm Sweep BEE 3 Star rated (service value >=5.0 to< 5.5 )

Providing & Fixing of of ventilating fans Capacitor start, copper wounded, single phase with PVC impeller, ABS body, automatic openable louver shutter in existing opening including making connection, testing etc. as required. OEM shall be an ISO certified company. Appropriate OEM test certificate shall be submitted by contractor. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

200 mm sweep

Providing & Fixing of extra down rod of 15 mm dia . ERW (Electrical resistance welded ) of 1.6mm nominal thick medium duty steel pipe including cutting, threading, drilling, fixing quarter pin etc as reqd. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

Providing & Fixing of IP20 SMD Mid Power LED batten type integrated light fixture made from polycarbonate /extruded aluminium powder coated housing with in built driver , Power Consumption of 18W/20W ,system lumen efficacy ≥ 120 lm/Watt output, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% ,p.f.≥0.95, CRI >80 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing.

OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) certificate / Report from OEM shall be submitted. All as per pre approved by engineer in charge . foe additional technical parameters of product/ work, refer Annexure "A" attacheded with this BSR.

4' LED Tube shape fixture 18/20 W (Extruded Al Base)

Providing & Fixing of IP40 LED Recessed / Surface Mounted, Round / Sqaure Non-Dimmable Back lit SMD Mid Power LED Downlight with die-cast aluminum housing & Heat Sink for heat dissipation with UV Stabilized non yellowish Diffuser with internal/ external BIS complience 2.5 KV surge protected Isolated driver, with Short & Open circuit protection, having efficiency > 85% and in compliance to IEC standards. System Lumen efficacy of ≥ 120 lm / watt, THD < 10 % ,p.f.≥0.95, CRI >80, life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) ,maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate (T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing.

OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) certificate / Report from OEM shall be submitted. All as per pre approved by engineer in charge . foe additional technical parameters of product/ work, refer Annexure "A" attacheded with this BSR.

Recessed Mounting

LED Downlight 9/10W

LED Downlight 14/15W

LED Downlight 18/20W

Surface Mounting

LED Downlight 6/7 W

LED Downlight 12/14 W

LED Downlight 18/20W

Providing & Fixing of IP40 LED Surface/ Recessed / suspended mounting Mid power SMD type LED Light fixture made from CRCA sheet steel housing, high purity / transmisivity UV stabilized Non - yellowish diffuser for uniform light distribution. High efficiency with 2.5 KV internal/external surge protection BIS certified isolated driver having efficiency > 85% , with Short & Open circuit protection and in compliance to IEC standards (Integral with light fixture). System lumen efficacy of ≥ 120 lm/Watt ,THD < 10 % , p.f.≥0.95,CRI >80 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing.

OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) certificate / Report from OEM shall be submitted. All as per pre approved by engineer in charge . foe additional technical parameters of product/ work, refer Annexure "A" attacheded with this BSR.

Recessed Mounting

36W LED light fixture 2'x2' with acrylic / prismatic front cover.

48W LED light fixture 2'x2' with acrylic / prismatic front cover

Providing & Fixing of IP65 IK10 rated Integrated SMD Mid power LED bulk head type light fixture made from Pressure Die Cast AL housing suitable for moutning LED tube system (integral driver), system lumen efficacy≥100 lm/Watt output , THD < 15% ,p.f.≥0.95,CRI >80 , life time of minimum 30000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. surge protection 5 KV.

LED BULK head luminaire 9/10W

LED BULK head luminaire 15 W

Providing, Fixing, Jointing, Testing & Commissioning of Medium duty MS B class pipes conforming to IS 3589 / 1239 part-I for DG Exhaust applications including cutting, welding etc & fittings like elbows,flanges, tapers, reducer, gaskets etc. fixing the pipe on the wall/ceiling with suitable clamps, hanger and nuts bolts . including the cost of thermal insulation with 50 mm thick layers of LRB rock wool as per IS : 8183-1993 (64 kg/m3 density) & 26 SWG aluminium sheet claddings etc complete as required complete in all respect. OEM Must have BIS certificate and & shall have submit NABL/ OEM lab appropriate type test reports before execution as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

200 mm dia

Supply, Installation, Testing & Commissioning of HT metering cubical panel as approved By DISCOMs fabricated out of 14 SWG CRCA sheet steel in two compartment & MS angle of size 60mmX6mm having provision for Following: (i)Provision for fixing Trivector Meter (To be supplied by DISCOMs) (ii)Provision for fixing of combined CT PT Set (To be supplied by DISCOMs), (iii)TT Block, (iv) 6mm Bakelite sheet on all sides, (V) 3/6 core copper cable for interconnections etc. as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

Supply Installation testing & Commissioning of Radial / mixed flow ISI marked water filled submersible motor pump sets suitable for 100/150mm dia borewell. The size of adopter fixed on top of the motor should exceed the top of coupler , for safegaurd the coupler. The construction material of motor and pump should match IS: 8034:2018 and IS 9283 guideline. The radial flow pumpset should operate at 5 star energy efficiency level of BEE and mixed flow pump set should operate at 3 star energy level of BEE, accompained by valid BEE certificate. Motor should be IE2 class as per IEC 60034-2-1: 2007, IEC 60034-30: 2008, & IS12615:2011 with required accessories including making connection suitable for Bore well. The job includes labour part of lowering of riser pipe G.I./ H.D.P.E. with rope, cables & pump, installation of complete fitting and accessories, jointing of electrical cables up to switch board. All labour for testing of submersible pumps set and supply of water to water mains, complete in all respect . All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021. 150 mm diameter Submersible pump shall have following HP Rating, phase, Head range, Discharge range respectively. 10.0 HP, 3-Ø, (91 - 115)Mtr, (285-180) LPM

Supplying and Laying ISI marked P.V.C. insulated submersible cable as per PWD specification for electrical Works confirming to IS:694 and as per IS 8130 : 2013 of 1.1 kV grade .Wire should be made from 99.99% purity copper, class 5 stranding in acc. to IEC 60228 for lower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation PVC type A ,flame retardant as per IS 10810-53, better amperage rating as per VDE 0298 part 4 including making connection etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. All as per pre approved by Engineer in charge, making connections. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021. 10 Sqm 3 core flat

Supply Installation testing & Commissioning of ISO certified company made DOL/Star-Delta Starter panel made out from 1.6 mm thick powder coated CRCA sheet, enclosure comprising of over load protection relay, short circuit & single phasing protection, Illuminated ON / OFF push buttons, ammeter, voltmeter, indicating lamps etc. suitable for following rating motors complete in all respect. Appropriate type test certificate / OEM test report shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021. For Three phase Submersible / Mono block pump . 3.0 HP to 10.0 HP ( Star / Delta starter )

Providing & Fixing of Electrical insulating rubber matts as per PWDspecification for electrical Works, ISI marked confirming to IS: 15652 / 2006 with one side anti skid abberation marks and pasting the mat with synthetic rubber adhesive as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

11 KV, 2.5 mm thick with proof voltage 22 KV / 3 min. and Break Down Voltage 45 KV

Octagonal MS Poles made of S-355JO grade steel sheet , folded lengthwise to obtained Octagonal shape, having single longitudinal seam weld and hot dipped galvanised internally & externally in accordance with IS 2629. (See Table P -01 for specs.)

Supply, Erection and Fixing of hot dipped galvanised M.S. Overhang (48.3 X 3.25 mm) with cap (400 x 88.9 / 114.3 x 3.25 mm) over the existing poles. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

Single arm overhang

Double arm overhang

Providing & Fixing of IK07 IP 66 protected LED Street Light Luminaire on existing bracket/pole. Fixture made of powder coated single piece pressure die cast aluminum LM6/ ADC12 material with heat dissipation fins on housing with UV stabilized PC/Toughened Glass cover (UV stablzation report submitted for UV cover ) and secondary lens on each LED & should be SMD type . The System level Luminaire efficacy >=120 lm/ wt with High Power LEDs is to be used and potted driver must be potted & has a unique BIS R number with Input Voltage AC 120 to 270 V AC with High voltage Cutoff @>=300 V AC and Auto resetting Safety ,Input Frequency 50Hz±3% Power Factor >0.95 driver Efficiency >85% ,THD(I) <10% Humidity 10% to 90% RH Working Temp -5C to 45C . driver current <1000mA shown in LM79 report. The luminaire shall be BIS certified and T.C. certified. Life Expectancy Equal or more than 50000 burning hrs with Minimum 70% lumen maintened ,color Rendering Index >70 and CCT 5700K+355K. Surge protection shall be min ≥ 4 KV internal and min 10 KV external. driver should be Phase to phase protection of 440 V for 4 Hrs. Manufactures Word Mark/Name Engraved/Embossing on die cast housing to allow traceability/authenticity. Fixture shall be AS PER IS 10322 Complianced. OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

LED Street Light fixture 60 Watt

Providing & Fixing of IP-65 Protected LED aviation obstruction light luminaire comprising of die cast aluminium alloy housingwith Polycarbonate enclosure having more than 200 No's Low Power LED's having minimum power consumption 15 watts complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

aviation obstruction LED light luminaire Min. 15 Watts

NON BSR ITEM

Supply, Installation testing and commissioning of POP-UP BOX 12 Module Features a textured black face plate. Hard wired into power source and used in conjunction with all Power to Power Cables. The Table Pop Up Power Strip allows easy access to 3 Nos 6Amp Scoket & 2 RJ-45 Ports connections . Pop up slowly in 45 degree with damped spring structure Suitable to conference table, solderless, Complete in all respect as required

SITC of PPI(Per phase isolation) convertion kit for 4 Way DB complete as required

SITC of PPI I(Per phase isolation) convertion kit for 6 Way DB complete as required

SITC of PPI I(Per phase isolation) convertion kit for 8Way DB complete as required

SITC of PPI I(Per phase isolation) convertion kit for 12Way DB complete as required

Supply and installation of fabricated 14 SWG G.I race ways for drawing wires for Raw power, UPS power and communication. The race ways shall be complete with base and cover, junction boxes as required, extension pieces, couplers, end plates, earthing including mechanically cutting chases in floor/ wall etc & making the same good. The race way shall be surface / Concealed type to brick wall / flooring with necessary fixing accessories. All the raceway will have required compartments and all complete as per drawings, specifications, relevant standards, and direction of Engineer in charge.as per recommended makes of RFP.

Supply, Installation testing and commissioning of GI floor raceway of Height of 1.6 mm thickness with Including PCC cutting , Fixing bracket,coupler,Riser & accessories of civil works if required complete as required . Make:Legrand,MK

100X38mm (Single Compartment )

75X38mm (Single Compartment )

50X38mm (Single Compartment )

Supply, Installation testing and commissioning of GI junction box it should be positioned directly on the slab to provides access to cables at the intersection of trunkings or changes of direction. The junction box allows deviation of power and data cables. Screed height should be between 65 to 90mm. Junction boxes are supplied with a base with flyovers and a lid. A disposable cover protection is available as an option. Side plates are pierced to suit Raceways.

Supply, Installation testing and commissioning of Height adjustable junction box 65 - 90 mm 600 x 600 x 65 - 90 mm GI Floor junction box with Metal cover complete in all respect as required.

Supply, Installation testing and commissioning of Height adjustable junction box 65 - 90 mm 400 x 400 x 65 - 90 mm GI Floor junction box with Metal cover complete in all respect as required.

Supply, Installation testing and commissioning of Height adjustable junction box 65 - 90 mm 400 x 400 x 65 - 90 mm GI Cross Over Floor junction box with Metal cover complete in all respect as required.

Supply, Installation testing and commissioning of 300 x 300 x 65 - 90 mm MS Floor junction box complete in all respect as required.

Supply, Installation testing and commissioning of Height adjustable junction box 65 - 90 mm 300 x 300 x 60-95 mm GI Cross Over Floor junction box with Metal cover complete in all respect as required.

Supply, Installation testing and commissioning of Height adjustable junction box 65 - 90 mm 225 x 225 x 65 - 90 mm GI Floor junction box with Metal cover Complete in all respect as required.

Supply, Installation testing and commissioning of Height adjustable junction box 65 - 90 mm 225 x 225 x 65 - 90 mm MS Cross Over Floor junction box with Metal cover Complete in all respect as required.

Supply, Installation testing and commissioning of Height adjustable junction box 65 - 90 mm 150 x 150 x 665 - 90 mm GI Floor junction boxwith Metal cover Complete in all respect as required

P & F of Early streamer Emission type lightning arrester on GI mast with air terminal configured as spheroid which is comprised of separate electrically isolated 4 panels surrounding an earthed central finial, the terminal shall be tested by CPRI for impulse current of 45 kA ( 8 / 20 Sec ) with 5 positive & 5 negative impulse, the arrester having following protection radius at level 1 Device shall comply NFC 17-102 and UNE 21186 standards. The device shall be mounted at least 4-5 meters high clear to highest point on the roof top with proper mounting arrangement. ESE for radius 50 mtr for level 1 protection

ESE for radius 50-68 mtr for level 1 protection

Supplying and erecting danger notice board for medium voltage installation to be erected as per I.S. The board should be 150 x 150 mm.

Supplying and erecting danger notice board for high voltage installation to be erected as per I.S.

Supplying and erecting printed instruction chart both in English & REGIONAL LANGUAGE & duly framed out on glass for treatment of person suffering from Electric shock.

Supplying pair of rubber hand gloves suitable for working on 11 KV/22 KV supply.

Supplying and fixing Standard First aid box with all the Standard contents.

SITC OF WATER Proof Boxes fro out door lighting IP-68 (of Size- 275 X 275 X 146 mm)

SITC OF Cable junction boxex IP67 1.5 MM2-4sqmm ,CU-3 wth terminal cable entry knockouts

SITC OF Cable junction boxex IP67 2.5 MM2-6sqmm ,CU-3 wth terminal cable entry knockouts

SITC OF Cable junction boxex IP67 4.0 MM2-10sqmm ,CU-3 wth terminal cable entry knockouts

Providing & Fixing of ISO Certified company made ISI marked (IS:2082) of 5 star rated vertical storage water heater with outer casing made of M.S.sheet finished with anti-corrosive powder coating,inner tank made of pure electrolytic copper/stainless steel / SPHP, Tubular copper sheathed and Nickel plated heating element/ twin ceremic cartridge heating element, stem type thermostat and thermal cut out, Dual indicating lamps for power supply and thermostat, PUF insulation, Pressure release valve,fusible plug etc. as required held in position with 4 no. rag bolts,duly wired with 3 core 2.5/4.0 Sqmm PVC insulated & sheathed copper conductor and 16 A/25A three pin plug top with Portable Residual Current Device ( PRCD ) facility form OEM ,including making inlet,outlet heavy gauge C.P./ Flexible alloy connection,testing etc. complete in all respect. Appropriate OEM test certificate shall be submitted by contractor. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

Providing & Fixing of Heavy duty capacitor start, copper woind Double ball bearing 900/1400 RPM single phase Exhaust fan as per PWD specification for electrical Works, conforming to IS:2312 ISI marked in existing opening including making connections testing etc. as Works, conforming to IS:2312 ISI marked in existing opening including making connections testing etc. as required. OEM shall be an ISO certified company. Appropriate OEM test certificate shall be submitted by contractor.

450 mm sweep(900/1400 RPM)

600 mm sweep(700 / 900 RPM)

SITC of ISO Certified company made MNRE approved & confirming to IS:12933 P-1,2,3 & 5 Flat Plate Collector type solar hot water system with collector, insulated stainless steel (SS grade:304) storage tank with electrical back up with Portable Residual Current Device ( PRCD ) facility form OEM , CRCA Powder coated /MS stand for Collector & Tank etc. as required. of following capacity complete in all respect. Appropriate OEM test certificate shall be submitted by contractor. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

500 litre/ day

Providing & Fixing of 3 Way Connector equivalent to 3 pin ceiling rose for False Ceiling as per PWD specification for electrical Works, made out from industrial grade Polycarbonate or fire resistant ABS material. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

Providing & Fixing of ISI marked (IS:2268-1994) ding dong/musical chime bell as per PWD specification for electrical Works, including making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

Providing & Fixing of following modular accessories as per PWD specification for electrical Works, made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating , minimum width of 1 module switch toggle( PUSH PART ) should not less then 20mm, including all as per pre approved by Engineer in charge,making connections, testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer Annexure "A" Rajasthan PWD BSR 2021.

Blanking plate

Supply installtion of Prepaied metering Software for 250 Useres

SITC of wall/ free standing floor mounted dust and vermin proof compartmentalised cubical panel as per attached SLD and GA drawing and as per TTA & PTA specification for electrical Works, made out of CRCA sheet . Other parameters required as per point (a) ,(b), (c)below:-

(a)Thickness of sheet shall not be less than 1.6 mm up to 600 mm length / width of any compartment and be of 2.0 mm above 600 mm. Load bearing structure shall be of 2.0 mm thick sheet supported by base M.S. channel if required . Side walls and cable alley compartments having bolted type doors with / without detachable extension type structure

(b)panel shall be duly treated for derusting in 7 tank process with dephosphating and with powder coating of minimum 70 microns on both side of panel in desired shade The panel having PU/ Neoprene rubber gasket of not less than 3mm thickness ,required hardware, separate detachable gland plate M.S. base channel (min75mm) , hinged door with locking arrangement for equipment/switchgear

[c) Interconnection between bus bar and switchgears /cable shall be rigidly supported and made out by flexible copper wires (up to 125 amp ) and by solid bus bar (>125 amp ) . All joints / interconnections of copper bus bar shall be dully tinned . Clearance between main bus bar and risers / metal parts shall be at least 10 mm additional to width of bus bar Bus bar is insulated by Heat Shrinkable sleeves . Earth and Neutral bus bar shall be half of the size of phase bus bar.

Academic block

MAIN I/C PANEL

APFC PANEL-300 KVAR (Admin Block)

ADMIN/ACADMIC BLOCK END FEED UNIT PANEL

UPS I/C PANEL

ADMIN/ACADMIC BLOCK UPS O/G PANEL WITH END FEED UNIT

APFCR PANEL-700 KVAR for Chiller plant

GROUND FLOOR TOWER-1 COMMON AREA PANEL

MAZZ. FLOOR TOWER-1 COMMON AREA PANEL

SECOND FLOOR TO 14TH FLOOR TOWER-1 COMMON AREA PANEL FLOOR PANEL ROOMTYPICAL PANEL

TERRACE FLOOR PANEL TOWER-1

GROUND FLOOR TOWER-2 COMMON AREA PANEL

MAZZ. FLOOR TOWER-2 COMMON AREA PANEL

SECOND FLOOR TO 17TH FLOOR TOWER-1 COMMON AREA PANEL

TERRACE FLOOR PANEL TOWER-2

GROUND FLOOR TOWER-1 COMMON AREA UPS PANEL

GROUND FLOOR TOWER-2 COMMON AREA UPS PANEL

TYPICAL FLOOR TOWER-1 COMMON AREA UPS PANEL FIRST FLOOR TO 14TH FLOOR

TYPICAL FLOOR TOWER-2 COMMON AREA UPS PANEL FIRST FLOOR TO 17 TH FLOOR

AUDITORIUM LIGHT & POWER TOWER-2

PLUMBING PANEL IN PUMP ROOM

GUEST HOUSE +DEAN RESIDENCE + DIRECTOR BUNGALOW

MAIN I/C PANEL @ GUEST HOUSE +DEAN+DIRCTOR

DG. SYNC. PANEL GUEST HOUSE +DEAN+DIRCTOR

APFCR PANEL-100 KVAR

MAIN LT PANEL (GUEST HOUSE+ DEAN RESIDENCE+ DIRECTOR BUNGALOW)

GUEST HOUSE MAIN SUB LT PANEL

GUEST HOUSE FLOOR PANEL ROOM

GUEST HOUSE TERRACE FLOOR PANEL

GUEST HOUSE TERRACE FLOOR VRV PANEL

DEAN RESIDENCE MAIN LT PANEL

FACULTY BLOCK

FACULTY BLOCK MAIN I/C PANEL

DG. SYNC. PANEL FACULTY BLOCK

APFCR PANEL-200 KVAR

MAIN LT PANEL (FACULTY BLOCK)

FACULTY BLOCK BBT END FEED UNIT PANEL

FACULTY BLOCK GROUND FLOOR COMMON AREA PANEL

FACULTY BLOCK FLOOR PANEL

FACULTY BLOCK TERRACE FLOOR PANEL

HOSTEL BLOCK

MAIN I/C PANEL

DG. SYNC. PANEL

APFCR PANEL-500 KVAR

MAIN LT PANEL HOSTAL BLOCK AND NON TEACHING

HOSTEL BLOCK (TYPICAL FLOOR 5 BLOCKS) -1,2,3,4,5 BBT END FEED PANEL

NON TEACHING BLOCK END FEED UNIT

HOSTEL BLOCK FLOOR PANEL -1,2,3,4,5

NON TEACHING BLOCK FLOOR PANEL

HOSTEL GROUND FLOOR COMMON AREA PANEL

HOSTEL TERRACE FLOOR COMMON AREA PANEL

NON TEACHING GROUND FLOOR COMMON AREA

NON TEACHING TERRACE FLOOR COMMON AREA PANEL

PARKING +GATE HOUSE+LANDSCAPE

MAIN LT PANEL PARKING+GATE HOUSE+AREA LIGHTING

APFCR PANEL-100 KVAR

GATE HOUSE MAIN LT PANEL

PARKING AREA PANEL

AREA LIGHT & GATE HOUSE ACADEMIC BLOCK AREA LANDSCAPE PANEL

FEEDER PILLAR (FOR EXTERNAL LIGHT ROAD LIGHT AND AREA LIGHT

Work Shop

Work Shop Main LT Panel

Work shop terrace panel

AC CHILLER PLANT

AC CHILLER PLANT MAIN PANEL

Sandwich Busduct

Supply of Sandwich 4 Pole Bus Trunking (3 Ph 4 W system) of Aluminium busbars with 50% integral G.I. housing as earth, Bus Trunking enclosure shall be made of 1.6mm thick G.I. sheet, IP55 for Indoor & IP67 + Canopy 1.2mm GI sheet for Outdoor application, multi layer insulation of Class-F, Temperature rise as per IEC 61439 – 1&6 and 2 nos of external aluminium earthing.

4000A/50KA SC for 1 sec (Straight Length), IP55 Indoor

90 Degree Bends

Copper Flexible with End Connections

3000A/50KA SC for 1 sec (Straight Length), IP55 Indoor

90 Degree Bends

Copper Flexible with End Connections

1600A/50KA SC for 1 sec (Straight Length), IP67 + Canopy 1.2mm GI sheet for Outdoor

90 Degree Bends

Copper Flexible with End Connections

3000A/50KA SC for 1 sec (Straight Length), IP55 Indoor

90 Degree Bends

Copper Flexible with End Connections

1600A/50KA SC for 1 sec (Straight Length), IP67 + Canopy 1.2mm GI sheet for Outdoor

90 Degree Bends

Copper Flexible with End Connections

1600A/50KA SC for 1 sec (Straight Length), IP55 Indoor

90 Degree Bends

Copper Flexible with End Connections

Sandwich Rising Mains

Supply of Sandwich Rising Mains of 4 Pole (3 Ph 4 Wire system) of Aluminium busbars with 50% integral G.I. housing earth, Bus Trunking enclosure shall be made of 1.6mm thick GI, degree of protection IP54, multi layer insulation of Class-F, Temperature rise as per IEC 61439 - 1&6. Including 2 runs of external aluminium earthing, through out the length of the Rising Main, End cover, Vertical supports, Spring Hanger, Rigid Hanger and One plug in point provision at every floor.

800A/50KA SC for 1 second

600A/40KA SC for 1 second

400A/25KA SC for 1 second

350A/25KA SC for 1 second

320A/25KA SC for 1 second

250A/25KA SC for 1 second

200A/25KA SC for 1 second

150A/25KA SC for 1 second

Supply of Tap off Boxes shall be fabricated out of 1.6mm GI sheet with 25KA 4P T.M. MCCB

Supply of End Feed Unit Box shall be fabricated out of 1.6mm GI sheet with 4P MCCB

800A/50KA SC for 1 second

600A/40KA SC for 1 second

400A/25KA SC for 1 second

350A/25KA SC for 1 second

320A/25KA SC for 1 second

250A/25KA SC for 1 second

200A/25KA SC for 1 second

Description of Work / Item(s)

Amount

Supply Installation testing and commissioning of HT VCB Panel 11KV 1250A 26.3KA having 1 Incomer VCB and 2 Outgoings VCB as per attached Specification

Supply Installation testing and commissioning of Ring Main Unit 11KV 630A having 1 VCB Module as incomer and 3 VCB Module asoutgoing per attached Specification

Supply Installation testing and commissioning of Ring Main Unit 11KV 630A having 2 VCB Module and 1 Load break Switch as per attached Specification

SITC of Cast Resin Dry type 11 KV/0.440 KV dry type transformer Dyn11 for indoor application as per attached specifications.

SITC of Silent DG Set (As per CPCB norms) complete with PCC 3.3 CONTROLLER or equivalent, 1500 RPM Diesel Engine of suitable BHP & AC Brush less SPDP Alternator mounted on a common base Frame & coupled through a flexible coupling or close coupled. Alternator shall be self regulated with standard Alternator Protection( Over voltage , over speed & under voltage, under speed warning & shutdown). Engine shall have residential silencer, electronic governor, Manual & electric Start ,Batteries, Engine instruments panel, AVM and with Weatherproof, powder coated Accoustic enclosure for DG set for sound attenuation fabricated from 1.6 mmCRCA sheet steel (structure) with side wall fabricated from 1.6 mm CRCA sheet & filled with 100mm thick glass wool(96Kg/m3)/Foam. as per IS 8183 the doors of 100 mm thick and fabricated from 1.6mm CRCA sheet packed with accoustic material, canopy fixed with axial flow fan , All doors/ opening are sealed with neoprene/EPDN gaskets. The enclosure has built in fuel tank, residential silencer (isolated from main DG chamber) with protection and tripping of DG set.against temperature of more than 50 degree centigrade. All controls for operation of DG set are from outside the enclosure with DG control panel having Microprocessor based Genset monitoring & control system, MCCB/ACB, Ammeter, Voltmeter, PF meter, frequency meter, KWH meter, Ind.lamps etc. mounted inside enclosure , visible and accessible from outside. The enclosure should be suitable for following capacity DG sets and alternator. Noise level shall be less than 75 dBA at a distance of 1 Mtrs. duly certified by authorised agency etc. complete in all respect of following capacity :-

160 KVA (Guest House:2 Nos Parking gate House :1 Nos Faculty Block:2 Nos

Providing, Fixing, Jointing, Testing & Commissioning of Medium duty MS B class pipes conforming to IS 3589 / 1239 part-I for DG Exhaust applications including cutting, welding etc & fittings like elbows,flanges, tapers, reducer, gaskets etc. fixing the pipe on the wall/ceiling with suitable clamps, hanger and nuts bolts . including the cost of thermal insulation with 50 mm thick layers of LRB rock wool as per IS : 8183-1993 (64 kg/m3 density) & 26 SWG aluminium sheet claddings etc complete as required complete in all respect. OEM Must have BIS certificate and & shall have submit NABL/ OEM lab appropriate type test reports before execution as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021 .

150 mm dia

200 mm dia

Providing & Laying XLPE insulated as per IS:7098/II/85 H.T.cable as per PWD specification for electrical Works for working voltage 11 K.V.(E) in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench with filling of excavated earth in trench , on existing cable trays or on surface etc. including making necessary connection, testing etc. as required of size as per points (a), (b), (c) mentioned below:-

(a) Material :- H4- Grade aluminium conductor of purity >99.6 % & as per IS:1554 P-I / IS :7098 P - I

(b) conductor shall have electrolytic aluminium confirming to IS 8130, IS 3975-1999 for armouring of cables , IS 5831 for sheath, IS 10810 (Part 0 to 64 ) for testing procedures

(c) OEM Must have ISO 9001 & 14001 certifications for quality assuarance & its own in house NABL lab setup for all testing facilities for cables . All above as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021

3 core 185.0 Sq.mm

Providing & making heat shrinkable type indoor/outdoor/straight through terminations/ joint kit as per PWD specification for electrical Works suitable for 11 KV / 33 KV cable with required components, prepration of cable ends. Type test report should be as per IS13573:2011 which covered all sequence for table 2 for termination kit and table 3 for streight through joint inclusive thermal & dynamic short circuit test, humidity test, soil fog test. Cross linking shall be done out side factory with E- beam/ peroxide technology. Extrusion process shall be in house OEM within same vicinity. OEM test lab should be as per ISO 9001:2015 & 14001 : 2015 & reports submitted to engineer in charge including testing etc. as required of following sizes. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021.

11 KV End Termination Kit Indoor type

3 core 120/150/185/225 Sq.mm

11 KV End Termination Kit Outdoor type

3 core 120/150/185/225 Sq.mm

Providing & Laying of 25 cm thick layer of river sand to cover of existing cable in 30 cm x 100/ 120 cm size cable trench with levelling and making symmetric 25 mm thick layer in complete running length of trench as required.

Labour charges for Excavation of 30cmx120cm size loose soil trench including refilling of excavated earth,compaction of earth, making good the same complete as required .

Providing & covering of existing cable lying in existing trench by IInd class bricks/ Stone slab of minimum 32mm thick and 250 mm wide in complete running length of trench complete as required.

Description of Work / Item(s)

Amount

SITC of Solar Grid Tied Power Plant of following KW AC output complete in all espect including structure , solar panels , grid tied inverter , connecting AC and DC cables , AC and DC protection ,DC and AC Interconnectiong cables ,DC and AC Distribution Box , Solar meter , MCCB for protection , Pressure pupms with CPVC pipes for cleaning as per Technical specifications and makes enclosed in RFP .

10 kw ( Land scape )

25 kw ( Hostel Blocks )

35 kw for( Guest House , Dean Director residence , Non teaching blocks )

50 kw ( Parking )

80 kw ( Academic Block )

100 kw ( Faculty Block )

Description of Work / Item(s)

Amount

Supply, instalaltion testing and commissioning of 120 KW/KVA modular,UPS System, Chassis size150 kVA, 3 X 3, 3 Phase, 415V, Modular Distribution Design as per detail specifications enclosed Consisting of Electric Cabinet for Rack-mounted Standard High-Frequency Link 3PH I/O 150kVA Intelligent UPS 30 kVA Power module BCB-120/ 150KVA APM Parallel /LBS Control Cable - 10 M Unity DP card Dry contact card Blank plates " 12V SMF Battery, 1 Set of 34 Blocks,150Ah for 15 min back up @60KW load at unityPF " Battery Rack Battery IRIT " Nyvin Cable of 1 runs of size 2 (Idc=180 Amps, Std Dist=30 Mtr from UPS to Battery)"

SITC of monolethic online UPS, 20 kVA, 3 Phase, 415 V with inbuilt isolation transformer as per detailed technical specs and Preferred makes with battery circuit breaker - UV trip , Parallel Cable , SNMP Card , 1 sets of 32 Block , 42 AH , 12 V, 30 minute battery Back up , battery rack , Battery IRIT, Nyvin cables complete in all respect .

SITC of monolethic online UPS, 10 kVA, 3-1 Phase with inbuilt isolation transformer as per detailed technical specs and Preferred makes with battery circuit breaker - UV trip , Parallel Cable , SNMP Card , 1 sets of 20 Block , 26 AH , 12 V , 15 minute SMF battery Back up , battery rack , Battery IRIT, Nyvin cables complete in all respect .

Description of Work / Item(s)

Amount

Supplying, Installation, Testing & Commissioning of Local Fire authrity approved Electric Driven Main fire pump for Sprinkler / Hydrant applications suitable for automatic operation and consisting of following details given as A, B, C, D, E, F and G . (A) Horizontal Single / Multi stage Centrifugal End suction, back pull type pump complete for delivery of below mentioned discharge , with necessary Butterfly valve on the suction side ( all items to be matching with the suction side dia of the pump) and pressure gauge ,Butterfly valve and non return valve on the delivery side side ( all items to be matching with the delivery side dia of the pump) and including bypass arrangement for Testing of pump (B) Material of construction : Pump Casing - Cast Iron, Impellor - Bronze, Shaft - SS 410, Packing - Mechanical Seal (C)Pump shall be capable of furnishing not less than 150 % of rated capacity at a head not less than 65 % of the rated head. The shut off head shall not exceed 120 % of rated head (D) Squirrel cage induction motor suitable for 3 phase, 415 V, 50 HZ, Ac supply 2900 / 1450 RPM T.E.F.C confirming to IP:55 , of required HP suitable for the above pump ,along with flexible coupling , coupling guard complete in all respect . ( E) Common bed plate fabricated from mild steel channel for installation of pump and Motor (F) Pump is to be inspected by third party like RITES / PDIL at manufacturer's premises and inspection report is to be submitted. (G) Suitable cement concreat foundation duly plastered with anti vibration pads. (H) All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021 .

3750 LPM suitable for 150 Mtr Head, multi stage, 1500 RPM

SITC of Local fire authority approved Diesel Engine driven Pump suitable for automatic operation as per discharge defined beolw consisting of the following details given as A, B, C, D, E and F . (A) Horizontal Single / Multi stage Centrifugal End suction, back pull type pump complete for delivery of below mentioned discharge complete with necessary flexible pipe, Butterfly valve on the suction side ( all items to be matching with the suction side dia of the pump) and pressure gauge ,Butterfly valve and non return valve on the delivery side side ( all items to be matching with the delivery side dia of the pump) and including bypass arrangement for Testing of pump (B) Material of construction : Pump Casing - Cast Iron, Impellor - Bronze, Shaft - SS 410, Packing - Mechanical Seal (C)Pump shall be capable of furnishing not less than 150 % of rated capacity at a head not less than 65 % of the rated head. The shut off head shall not exceed 120 % of rated head (D) Radiator cooled Diesel Engine developing suitable BHP for the below mentioned discharge at 1500 / 1800 RPM, flexible coupling and coupling guard with the Pump, common bed plate for mounting of the Engine and Pump,Antivibration damping arrangement by cushy foot, Diesel Engine starting Panel for starting of the engine automatically if the Normal electrical supply fails with a unit of battery bank of 12/24v,180 Ah, Lead Acid Battery with Boost / Trickle charger as required for operation of Diesel engine, Exhaust Pipe of suitable diameter minimum 10 M length, with muffler, day oil tank of 300 1ts capacity with first charge and hand operated oil pumping set, (E) Pump is to be inspected by third party like RITES / PDIL at manufacturer's premises and inspection report is to be submitted. (F) Suitable cement concreat foundation duly plastered with anti vibration pads. (G). First filling of the fuel tank shall be done by contractor and the prevailing fuel cost at that time shall be reimbursed to the contactor by department. Appropriate OEM/ NABL lab test reports shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021 .

3750 LPM suitable for 150 Mtr Head, multi stage, 1500 RPM

Supplying, Installation, Testing & Commissioning of central govt./ state govt. authorised fire authority approved Horizontal single stage Jockey pump with CI Body, Bronze impellor, SS shaft, mechanical seal coupled with Squirrel cage induction motor should be IE2 class as per IEC 60034- 2-1: 2007, IEC 60034-30: 2008, & IS12615:2011 for automatic operation suitable for three phase, 415 V, 50 Hz AC supply with synchronous speed of 2900 RPM ,T.E.F.C type confirming to IP:55 with flexible coupling and coupling guard with the pump ,Common bed plate fabricated from mild steel channel Suitable cement concreat foundation duly plastered with anti vibration pads.complete in all respect. Appropriate OEM/ NABL lab test reports shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021 .

180 LPM suitable for 150 Mtr

Providing & fixing 100mm dia bourden type, Stainless steel dial type pressure Gauge (0 - 16 Kg ) range, 3 / 8 " BSP bottom entry on Pump Delivery Line complete with Ball valve complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

Supplying, Installation, Testing & Commissioning of pressure switches for Main, Jockey, Terrace pump and standby Diesel pumps, including necessary control wiring From pressure switch upto control panel and Ball valve complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021 .

Providing & fixing vane type water flow switches with contacts for installation in 50 mm to 150 mm dia M.S. pipe for a service pressure up to 20 Kg / Sq.cm complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021 .

Supplying, Installation, Testing & Commissioning of floor mounted dust and vermin proof compartmentalised cubical type main fire pump control panel made out of CRCA sheet , required hardware ,duly treated for derusting in 7 tank process with dephosphating and with powder coating on both side of panel in desired shade The panel having PU/ Neoprene rubber gasket of not less than 3mm thickness , separate detachable gland plate M.S. base channel ,hinged door with locking arrangement for equipment/switchgear . Thickness of sheet shall not be less than 1.6 mm up to 600 mm length / width of any compartment and be of 2.0 mm above 600 mm. Load bearing structure shall be of 2.0 mm thick sheet supported by base M.S. channel if required . Side walls and cable alley compartments having bolted type doors and having accessories/ switch gear (as per Specf Ch-06 & 08) as below:- complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021 .

INCOMER

Out going

Providing, Fixing, Jointing, Testing & Commissioning of Heavy duty MS C class pipes conforming to IS 3589 / 1239 part-I for hydrent and sprinkler applications including cutting, screwing, welding etc & malleable iron fittings like elbows, tees, flanges, tapers, reducer, with compressed asbestos gaskets etc. fixing the pipe on the wall/ceiling with suitable clamps, hanger and nuts bolts as per approved spacing. complete with painting of one coats of Red Oxide and two or more coats of synthetic enamel paint of Post office red shade complete as required.Complete installtion shall be pressure tested at 14kg/sqcm for 24 hr as per practice complete in all respect. Appropriate Test Certificate/ report of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021 .

25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

100 mm dia

150 mm dia

250 mm dia, 6.35 mm thick

300 mm dia., 7.0 mm thick

Providing, Fixing, Jointing, Testing & Commissioning of Heavy duty MS C class pipes conforming to IS 3589 / 1239 part-I for hydrent and sprinkler applications underground rings including cutting, screwing, welding etc & malleable iron fittings like elbows, tees, flanges, tapers, reducer with compressed asbestos gaskets, nuts, bolts etc. including laying of pipe in excavted trench of 1.0 mtr depth with cleaning,wrapping and coating of the pipe with 4 mm thick tar based polymaric corrosion protection tape including applying uniform coat of cold pipekot primer as per IS; 10221 for protection against corrsion.complete in all respect. (Excavtion of trench shall be paid extra as per Item no E130500 ). Complete installtion shall be pressure tested at 14kg/sqcm for 24 hr as per practice complete in all respect.Appropriate Test Certificate/ report of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021 .

80 mm dia

100 mm dia

150 mm dia

Supplying and fixing cylindrical air vessel of continuous welded construction for pump room made of 450 mm dia,fabricated out of 10 mm thick dished ends and 8 mm thick MS sheet, 2000 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia drain valve,air release valve,safety valve pressure gauge with required accessories and painting with two coats of Red Oxide and two coat of post office red enamel paint as required complete in all respect. Appropriate Test Certificate/ report of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021 .

Supplying and fixing cylindrical air vessel of continuous welded construction fixed at riser top made of 250 mm dia, fabricated out of 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia drain valve,release valve,safety valve pressure gauge with required accessories and painting with two coats of Red Oxide and two coat of post office red enamel paint as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021 .

Supplying and Fixing of Y type strainer fabricated out of cast iron/ steel body, strainer shall have 1.6 mm. thick stainless steel sheet perforated screen with 3 mm. dia holes with flange at both ends complete with nuts, bolts, washers, gaskets etc of following sizes. complete in all respect. Appropriate Test Certificate/ report of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021 .

150 mm dia

200 mm dia

Supply, installation, testing and commissioning of dual plate/ Double flenze non-return valve (PN-16) of following sizes confirming to IS:5312 -1975 complete with flanges,rubber gasket, nut,bolts, washers etc. complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021 .

80 mm dia

100 mm dia

150 mm dia

250 MM Dia

Supplying, fixing, testing commissioning of butterfly valve (PN 16) with Bronze/ Gunmetal seat duly ISI marked conforming to IS 13095-1991 complete with flanges,Nuts, Bolts, washers, gaskets of following sizes as required complete in all respect. Appropriate Test Certificate/ report of product/accessories from OEM shall be submitted.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021 .

50 mm dia

65 mm dia

80 mm dia

100 mm dia

150 mm dia

200 mm dia

Providing, installation, testing and commissioning of Brass ball valves (PN-16) duly ISI marked confirming to IS : 9890-1981 complete with flanges,Nuts, Bolts, washers, gaskets etc of following sizes as required complete in all respect. Appropriate Test Certificate/ report of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021 .

25 mm dia.

32 mm dia

40 mm dia

Providing & fixing testing & commissioning of installation control valve of cast iron body/ ductile iron and brass/bronze working parts comprising of water motor alarm, bronze seat clapper, and clapper arm, hydraulically driven mechanical gong bell to sound continous alarm when the wet riser/Sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc. of size 150 mm dia as required complete in all respect. Appropriate Test Certificate/ report of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021 .

Providing, Fixing, Testing & Commissioning of single headed obligue pattern hydrant landing valve (internal/external) ISI marked confirming to IS:5290-1983 (Type-A) /IS: 908 - 1975 with 80 mm dia flanged inlet & 63 mm dia instantaneous type female outlet coupling with cast iron wheel complete with cap and chain, twist release type plug and all accessories complete in all respect. Appropriate Test Certificate/ report of product/accessories from OEM shall be submitted.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021 .

Stainless Steel (SS 316) material

SITC HYDRANT WITH MONITOR Body Carbon steel 6 Inch NB Falnged Outlet 2 instantaneous and 4 Inch Falnged outlet fro monitor Stand post with water monitor 680 GMP/2580 LPM Flow Capacity 100 PSI

Supplying and fixing orifice plate 80MM to 150 made of 6 mm thick stainless steelwith orifice of required size in between flange & landing valve of external and internal hydrant to reduce pressure to working pressure of 3.5 kg/cm2 complete with rubber gasket, GI bolts, nuts, washers etc. as required complete in all respect. Appropriate Test Certificate/ report of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021 .

Supplying and fixing of Non-percolating flexible hose (RRL type-A) ISI marked confirming to IS:636, 63 mm dia, 15 mtr. Long RRL hose pipe with instanteneous type 63 mm dia male and female couplings (Confirming to IS:903) duly bound and riveted to hose pipes with copper rivets and copper wire etc. as required complete in all respect. Appropriate Test Certificate/ report of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021 .

With Stanless steel Coupling

Supplying & fixing Short Branch Pipe with Nozzle ISI marked conforming to IS: 903, made of following material , fitted with 20mm (nominal internal diameter) bore nozzle, for projecting water in form of solid jet. The Branch shall have 63mm Male Instantaneous Inlet, suitable for use with 63 mm size Fire fighting hoses. H.P. tested to 21 kgf/cm² for 2.5 minutes complete in all respect. Appropriate Test Certificate/ report of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021 .

Stainless Steel (SS 316) material

Supplying and fixing first -Aid Fire hose reel wall mounted swinging type with MS construction spray painted in post office Red, conforming to IS 884-1985 with upto date amendments, complete with the following as required. (A) 30 m long 20 mm (nominal internal) dia water hose (B)20 mm (nominal internal) dia gun metal globe valve & nozzle 5mm orifice (C)Drum and brackets for fixing the equipments on wall. (D) Connections from riser with 25 mm dia stop valve (gun metal) & M.S. pipe complete in all respect. Appropriate Test Certificate/ report of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021 .

with High Pressure Braided Rubber Hose as per IS:5132 - 1969

Supplying and fixing Fire Brigade In let Connection of CI body with Gun Metal/stainless steel male instantaneous inlet couplings complete with PVC blank cap and chain as required for 150mm dia MS pipe connection, conforming to IS 903 as required of following way :- complete in all respect. Appropriate Test Certificate/ report of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021 . :

Providing and fixing of Gun Metal/stainless steel Fire brigade Suction hose coupling (draw out connection) with nut for female coupling as per IS:902-1974 complete with 100mm dia valve, complete with nut bolts and rubber insertion complete as required complete in all respect. Appropriate Test Certificate/ report of product/accessories from OEM shall be submitted.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021 .

Supplying and fixing of Hose Cabinet made of 1.6 mm thick MS sheet with 6 mm thick glazed glass doors including necessary locking arrangement suitable to accommodate external hydrant with butterfly valve, 2 Nos 15 Mtr. Long Hose pipe, 1 No. branch pipe, mounted on wall duly painted with post office red externally and white internally with synthetic enamel paint complete in all respect, for internal/external hydrant complete as required. Appropriate Test Certificate/ report of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021 .

size 750 mm x 600 mm x 250 mm

Providing & fixing of size 0.9 M wide x 1.8 M height Indoor Hose Cabinet shutter suitable for accomodating hydrants made of Tubular rectangular pipe (50X25mm) having central opening 6mm thick glass glazed door having necessary locking arrangement, painting (one coat primer & two coats of paint) suitable for housing 2 Nos. RRL hose pipe, 1 no branch pipe, first Aid hose Reel etc . as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021 .

Providing, fixing, testing & commissioning of 15 mm dia size quartzoid bulb type sprinkler heads suitable for 68 degree centigrade rating standard response (UL/FM/LPC/TAC Listed/Approved) chrome plated complete in all respect of the following type complete in all respect. Appropriate Test Certificate/ report of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021 .

Pendant/ Upright type

Extended Throw Sidewall type .

Providing & fixing 10 SWG chrome plated brass 100 mm dia decorative flanges(rossette) / escutcheon plates fixed at junction of Sprinkler piping with the false ceiling complete in all respect. Appropriate Test Certificate/ report of product/accessories from OEM shall be submitted.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021 .

Providing, fixing, testing and commissioning 25mm diameter inspecting and testing assembly with gunmetal isolation valve gunmetal sight glass bypass valve and connected to 50mm drain line complete as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021 .

Supply & Fixing of Fire Man's Axe with carbon steel head & rubber moulde handel and confirming to IS :926 with length approx 0.4 M & weight 3.0 Kg. complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021 .

Supply and Fixing of Stainless Steel Flexible Hose Pipe, Made of Corrugated Stainless Steel, Rated Pressure 200psi –Assembly complete with: Inlet nipple with 1” NPT male thread, outlet reducer with 1/2" NPT female thread to sprinkler head, 700mm Square Bar, Centre Clamp & 2 Nos side brackets. complete as required complete in all respect. Appropriate Test Certificate/ report of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021 .

700 mm Long

1000 mm Long

Supply and installation with bracket / supports water based fire extinguisher Stored pressure type EN PED Approved and CE marked conforming to current and valid BIS certification IS 15683:2018 suitable for A class of fires Complete with delivery hose, squeeze grip release valve, locking arrangement, pressure gauge . Extinguisher should be pressurized using high grade Dry Nitrogen as per IS 1747 standard. OEM declaration should be submitted. Serial no. and date of manufacturing should be embossed or printed on the body of the fire extinguisher.The firm should submit the product certificate from an EN notified body & product performance test report from NABL accredited Lab as per IS 15683. . All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021 .

Capacity - 9 Ltrs.

Supply & Fixing ISI marked conforming to current and valid BIS certification IS 15683:2006 approved Poratable Fire Exitnguisher, Mech. Foam type (AFFF) of following capacity with gun-metal cap and nozzle and Complete with delivery hose, squeeze grip release valve, locking arrangement, pressure gaug complete in all respect.Extinguisher should be pressurized using high grade Dry Nitrogen as per IS 1747 standard, OEM declaration should be submitted. Serial no. and date of manufacturing should be embossed or printed on the body of the fire extinguisher. The firm should submit the product certificate from an EN notified body & product performance test report from NABL accredited Lab as per IS 15683. . All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021 .

Capacity - 6 Ltrs

Supply & Fixing of current and valid BIS certification IS: 15683:2018 approved Portable fire Extinguisher, Carbon-dioxide type flat base including valve, discharge hose of not less than 10 mm dia. min. 600 mm long & complete in all respects including initial fill with C02 gas confirming to IS:307-1966 filled to a filling ratio of not more than 0.667 and wall suspension bracket . bidder must have valid PESO license to refill and store compressed gas cylinders as per Gas Cylinder rules 2004 , vessel should be PESO Approved. carbon dioxide gas shall conform to IS 15222 with latest amendment. Co2 Cylinder shall be conform to all the requirement given in IS 7285:2004. Serial no. and date of manufacturing should be embossed or printed on the body of the fire extinguisher. The firm should submit the product certificate from an EN notified body & product performance test report from NABL accredited Lab as per IS 15683. . All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021 .

Capacity 4.5 Kg.

Supply & Fixing of ABC Type (MAP 50) type powder Fire Extinguisher (Stored Pressure type) of following capacity duly current and valid BIS certification conforming to IS: 15683:2006, with Dry chemical powder used as extinguishing agent should be Mono Ammonium Phosphate 50% concentration conforming to IS 14609:1999. OEM will produce supplier certificate complete with squeeze grip release valve, locking arrangement, pressure gauge and bracket including initial fill and wall suspension complete in all respect. Serial no. and date of manufacturing should be embossed or printed on the body of the fire extinguisher. The firm should submit the product certificate from an EN notified body & product performance test report from NABL accredited Lab as per IS 15683. . All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021 .

Supply & Fixing of ISI marked conforming to IS : 2878 Fire Extinguisher, Trolley mounted, CO2 (gas pressure) type capacity 22.5 Kg. with gun-metal cap.delivery hose horn, trolley, handle, wheel type release valve, locking arrangement complete in all respect. bidder must have valid PESO license to refill and store compressed gas cylinders as per Gas Cylinder rules 2004 , vessel should be PESO Approved. carbon dioxide gas shall conform to IS 15222 with latest amendment. Co2 Cylinder shall be conform to all the requirement given in IS 7285:2004. Serial no. and date of manufacturing should be embossed or printed on the body of the fire extinguisher. The firm should submit the product certificate from an EN notified body & product performance test report from NABL accredited Lab as per IS 15683. . All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" Rajasthan PWD BSR 2021 .

Providing and fixing mettalic expansion bellows vibration eliminators with flange suitable for raw water upto 45 deg. C. temperature working pressure 7 kg/ sq.cm and test pressure 14 kg/sq.cm.

80mm dia

150 mm dia

SITC of modular constuction master control annuciation panel for sprinkler with provision of required no.16 of zone (30 % additional spares ), each sprinklar hydrant will have atleast 2 zone on each floor, the panel shall have indication of zone sprinkler, zone fault, fire / fault hooter, alarm cancel for fire / fault, battery for emergency back up of 4 hrs. And wiring 2X1.5 Sqmm From flow switch to panel

FIRE ALARM SYSTEM (ADDRESSABLE TYPE)-

SITC of UL864 10th Edition UL Listed and FM approved Analog Addressable 10 Loop Fire Alarm control panel. Panel shall be running on full digital protocol with 32 bit Microprocessor . The Panel shall be complete with 6" color touch screen LCD Display / minimum 980 Characters. Fire alarm panel should have minimum capacity of 2500 detectors and devices in any combination and capable of making upto 50 loops in single panel using additional Loop cards. Each addressable loop shall be capable of taking 250 addresses per loop configuring either as all detectors or modules or any mix of both. The panel shall have the Fire Fighter Touch Screen Graphical Display panel to inform & guide Fire Fighters for carrying out Fire Fighting operations. The display shall have Hazmat icons indicating the presence of any explosive gas, liquids, poison,fumes etc. If this feature is not available in fire alarm panel then additional fire fighter touch panel along with necessary hardware and software should be provided by the manufacturers for fire fighters to guide them during emergency without any extra cost. To expedite system troubleshooting, the system cards shall have ground fault detection and diagnostic LEDs by card. In the display,simple building floor plan can be loaded in bitmap or jpeg format, On the map, the user will see an icon indicating the location of the event in the building in addition to a 'You-Are-Here' symbol to tell the responding person exactly where they are in the building in relation to the event. The system shall be polarity insensitive. The panel shall support degrade mode operation and shall have battery backup of 24 hrs in normal condition and 30 minutes in Alarm condition. As per recommended makes and specifications given in the RFP

Supply, Installation, Testing and Commisioning UL listed and FM approved of addressable Analog Fire Alarm Panel shall be running on full digital protocol with 32 bit Microprocessor based 3 Loop panel , Networkable analogue addressable type Fire Alarm Control Panel . The Panel shall be complete with 6" color liquid-crystal display (LCD) .LCD Display status highlights Alarm events appear in red; Trouble events appear in yellow; Supervisory events in blue, and Security events in magentay. System should be capable to have XXX intelligent initiation devices per panel. Each addressable loop shall be capable of not less than 250 addresses per loop configuring either as all detectors or modules or any mix of both. The panel shall have the Fire Fighter Touch Screen Graphical Display panel to inform & guide Fire Fighter for carring out Fire Fighter operation. The display shall have Hazmat icons indicating the presence of explosive gas, liquids, poison,fumes etc . To expedite system troubleshooting, the system cards shall have ground fault detection and diagnostic LEDs by card. In the display,simple building floor plan can be loaded in bitmap or jpeg format, On the map, the user will see an icon indicating the location of the event in the building in addition to a 'You-Are-Here' symbol to tell the responding person exactly where they are in the building in relation to the event. The system shall be polarity insensitive. The panel shall support degrade mode operation and shall have battery backup of 24 hrs in normal condition and 30 minutes in Alarm condition. As per recommended makes and specifications given in the RFP

Supply, Installation, Testing and Commisioning UL listed and FM approved of addressable Analog Fire Alarm Panel shall be running on full digital protocol with 32 bit Microprocessor based 2 Loop panel , Networkable analogue addressable type Fire Alarm Control Panel . The Panel shall be complete with 6" color liquid-crystal display (LCD). LCD Display status highlights Alarm events appear in red; Trouble events appear in yellow; Supervisory events in blue, and Security events in magentay. System should be capable to have XXX intelligent initiation devices per panel. Each addressable loop shall be capable of not less than 250 addresses per loop configuring either as all detectors or modules or any mix of both. The panel shall have the Fire Fighter Touch Screen Graphical Display panel to inform & guide Fire Fighter for carring out Fire Fighter operation. The display shall have Hazmat icons indicating the presence of explosive gas, liquids, poison,fumes etc . To expedite system troubleshooting, the system cards shall have ground fault detection and diagnostic LEDs by card. In the display,simple building floor plan can be loaded in bitmap or jpeg format, On the map, the user will see an icon indicating the location of the event in the building in addition to a 'You-Are-Here' symbol to tell the responding person exactly where they are in the building in relation to the event. The system shall be polarity insensitive. The panel shall support degrade mode operation and shall have battery backup of 24 hrs in normal condition and 30 minutes in Alarm condition. as per recommended makes and specifications given in the RFP

Supply, Installation, Testing & Commisioning UL listed and FM approved Network Repeater similiar to main fire alarm panel shall be running on full digital protocol with 32 bit Microprocessor .The Panel shall be complete with 6" color liquid-crystal display (LCD), touch screen and LEDs for displaying system status. LCD Display status highlights Alarm events appear in red; Trouble events appear in yellow; Supervisory events in blue, and Security events in magentay. As per recommended makes and specifications given in the RFP

SITC of UL268 7'th edition compliance and FM approved Intelligent Addressable multi-criteria detector (optical and thermal sensors) complete with standard base, facility to mount in different comprehensive environment, Tri-color detector-status LED with 360 ° view, microprocessor circuitry with error check; detector self-diagnostics and supervision programs,Rate-of-Rise Detection: 15°F / min. (8.3°C / min.) - Fixed: 135°F (57°C) , Field programmable as rate-of-rise or fixed temperature, Polarity insensitive, Superior EMI and RFI immunity, RoHS compliant. Detector shall have in-built isolator for better reliability, circuit integrity and advanced fault finding. Manufacturers not having in-built Isolator feature in detector shall consider Isolator base in place of standard base OR separate Isolator before and after every detector to comply the same without any extra cost. As per recommended makes and specifications given in the RFP

Supply Installation, Testing & Commissioning of Beam detector with addressable monitor module to programme the detectors, complete as required. As per recommended makes and specifications given in the RFP

SITC of UL listed and FM approved Intelligent addressable Class X type (Style 7), Control Module with built in dual isolator, polarity insensitive, Tri color LED for status (Green for Normal,Yellow for Faulty and RED for activation), Operating Temp and RH: 0-49degC and <=95%. Module shall have in-built isolator for better reliability, circuit integrity and advanced fault finding. Manufacturers not having in-built Isolator feature shall provide separate Isolator before and after every Module to comply the same without any extra cost. (For AHU & Staircase Pressurization Fans, Hooters / Sounders / Strobes etc. As per recommended makes and specifications given in the RFP

SITC of UL listed and FM approved Intelligent addressable Class X type (Style 7), Mini Monitor Module with built in dual isolator, polarity insensitive, Tri color LED for status (Green for Normal,Yellow for Faulty and RED for activation), Operating Temp and RH: 0-49degC and <=95%. Module shall have in-built isolator for better reliability, circuit integrity and advanced fault finding. Manufacturers not having in-built Isolator feature shall provide separate Isolator before and after every Module to comply the same without any extra cost. (For Sprinkler Flow Switches and door holders). As per recommended makes and specifications given in the RFP

Supply, Installation, Testing & Commissioning of Response indicator. as per recommended makes and specifications given in the RFP

SITC of UL listed and FM approved Intelligent addressable Class X type (Style 7), Manual Pull Station Single Action, Shock and Vibration Resistant, with built in dual isolator, polarity insensitive, Tri color LED for status (Green for Normal,Yellow for Faulty and RED for activation), T-45 Key Reset lockset for easy maintenance, Operating Temp and RH: 0-49degC and <=95%. MCP shall have in-built isolator for better reliability, circuit integrity and advanced fault finding. Manufacturers not having in-built Isolator feature shall provide separate Isolator before and after every MCP to comply the same without any extra cost. as per recommended makes and specifications given in the RFP

SITC of UL Listed Sounder cum Strobe rated at 75 dBA @ 3m for Audible annunciation and 75cd flashintg at 1 Hz for visual indication. Approved Make : Cerberus by Siemens / Ansul/Gamewll/Ncom. as per recommended makes and specifications given in the RFP

SITC of UL Listed Fire Fighter's Telephone Jack with suitable module for two way communication between Remote Fire Fighter & Fire Command Center. as per recommended makes and specifications given in the RFP

SITC of UL Listed Fire Fighter's Telephone Handset for two way communication between Remote Fire Fighter & Fire Command Center. as per recommended makes and specifications given in the RFP

Providing and fixing in position following sizes of MS conduits including providing all accessories concealed/ exposed as required.

25 mm dia MS conduit (16 GAUGE)

Providing and fixing in position the following sizes heavy duty ISI marked 2mm thick PVC conduit including all accessories (i.e clamps, nuts,bolts, bends, junction boxes, pull boxes etc.) & good in all respect as the case may be:

25 mm dia PVC (RECESSED IN SLAB/WALL)

Supplying and fixing in position MS anodised box suitable for fixing of Detectors on True Ceiling complete as required.

PA SYSTEM

SITC of 1X500W/480W Amplifier and can provide automatic re-settable overcurrent, overload, overheating, overvoltage, under-voltage and DC protection

SITC of integrated Audio source with the following features : • Two single CD\USB\SD and DAB\FM line outputs can play music applications in two areas. • The volumes of the two line outputs can be adjusted separately. • CD\USB\SD has three play modes: single play, all play and repeated play. • DAB\FM can preset 10 channels of programs. • RS485 remote control interface

SITC of 6W Wall Speaker with tappings at 6W/3W/1.5W

SITC of 6W Wall Speaker with tappings at 6W/3W/1.5W

SITC of Suitable Size PAVA Rack for Controller & Amplifiers.

Description of Work / Item(s)

Amount

Supply / installation / testing and commissioning of 26 passanger lifts in Academic Block Tower A with machine room , 2.5 M/sec travel speed , 15 Stop , 15 openings , Triplex / Duplex/ simplex control as per detailed specifications and recommended makes given in RFP

Supply / installation / testing and commissioning of 26 passanger lifts in Academic Block Tower B with machine room , 2.5 M/sec travel speed , 20 Stop , 20 openings , Triplex / Duplex/ simplex control as per detailed specifications and recommended makes given in RFP

Supply / installation / testing and commissioning of 8 passanger lifts in Guest house , machine room less , 1 M/sec travel speed , 3 Stop , 3 openings , Duplex/ simplex control as per detailed specifications and recommended makes given in RFP

Supply / installation / testing and commissioning of 15 passanger lifts in Guest house , machine room less , 1 M/sec travel speed , 4 Stop , 4 openings , simplex control as per detailed specifications and recommended makes given in RFP

Supply / installation / testing and commissioning of 8 passanger lifts in Dean & Director Residence , machine room less , 1 M/sec travel speed , 4 Stop , 4 Openings , Duplex control as per detailed specifications and recommended makes given in RFP

Supply / installation / testing and commissioning of 15 passanger lifts in Hostel block , with machine room , 2.5 M/sec travel speed , 10 Stop , 10 openings , Duplex control as per detailed specifications and recommended makes given in RFP

Supply / installation / testing and commissioning of 15 passanger lifts in Faculty block , with machine room , 2.5 M/sec travel speed , 10 Stop , 10 openings , Duplex control as per detailed specifications and recommended makes given in RFP

Supply / installation / testing and commissioning of 15 passanger lifts in Faculty block , with machine room , 2.5 M/sec travel speed , 11 Stop , 11 openings , Simplex control as per detailed specifications and recommended makes given in RFP

Supply / installation / testing and commissioning of 15 passanger lifts in non Teaching block , with machine room , 2.5 M/sec travel speed , 8 Stop ,8 openings , Duplex control as per detailed specifications and recommended makes given in RFP

Supply / installation / testing and commissioning of 15 passanger lifts in non Teaching block , with machine room , 2.5 M/sec travel speed , 9 Stop ,9 openings , Simplex control as per detailed specifications and recommended makes given in RFP

Supply / installation / testing and commissioning of 15 passanger lifts in Workshop block , machine room less , 1 M/sec travel speed , 5 Stop ,5 openings , Trplex control as per detailed specifications and recommended makes given in RFP

Description of Work / Item(s)

Amount

Supply , Installation , Testing and commissioning of 4 MP Varifocal Bullet Network Camera -1/1.8'' Progressive Scan CMOS, 2680 ×1520 at 25fps, 2.8 to 12 mm Varifocal Auto iris lens, 0.001 Lux at F1.2, 0 Lux with IR on, ICR, ONVIF (PROFILE S, PROFILE G, PROFILE T), Support H.265, H.264, MJPEG, 140db WDR, BLC, HLC, Defog, EIS, Distortion Correction, 3D Digital Noise Reduction, Three individually configurable stream, 12 VDC & PoE, IR range: 50m, Support on-board storage up to 256 GB (SD card not included), Alarm : 2 inputs & 2 outputs, Audio: 1 input & 1 output, IP67, IK10, Edge Analytics- Line crossing detection, Intrusion detection, Scene change detection, Audio exception detection, Defocus detection, Motion detection, Face Recognition, Hard Hat Detection, Face Counting, Queue Management, audio exception detection, Video tampering, Region entrance detection, Region exiting detection, UL, FCC, CE certified. as per detail specifications and Preferred makes enclosed in rfp

Supply , Installation , Testing and commissioning of 4 MP Varifocal Dome Network Camera -1/1.8'' Progressive Scan CMOS, 2680 ×1520 at 25fps, 2.8 to 12 mm Varifocal Auto iris lens, 0.001 Lux at F1.2, 0 Lux with IR on, ICR, ONVIF (PROFILE S, PROFILE G, PROFILE T), Support H.265, H.264, MJPEG, 140db WDR, BLC, HLC, Defog, EIS, Distortion Correction, 3D Digital Noise Reduction, Three individually configurable stream, 12 VDC & PoE, IR range: 50m, Support on-board storage up to 256 GB (SD card not included), Alarm : 1 input & 1 output, Audio: 1 input & 1 output, 1 built-in microphone, IK10, Edge Analytics- Line crossing detection, Intrusion detection, Scene change detection, Audio exception detection, Defocus detection, Motion detection, Face Recognition, Hard Hat Detection, Face Counting, Queue Management, audio exception detection, Video tampering, Region entrance detection, Region exiting detection, UL, FCC, CE certified. as per detail specifications and Preferred makes enclosed in rfp

Supply , Installation , Testing and commissioning of 2 MP IR Fixed Dome Network Camera for lift -1/2.8″ Progressive Scan CMOS, 1920 × 1080 at 25fps, 2.8 mm Fixed lens, 0.002 Lux at F1.4, 0 Lux with IR on, ICR, ONVIF (PROFILE S, PROFILE G, PROFILE T), support H.265, H.264, MJPEG, 120db WDR, 3D Digital Noise Reduction, Three individually configurable stream, 12 VDC & PoE, IR range: 40m, Support on-board storage up to 256 GB (SD card not included), IP67, IK 10, Edge Analytics- Line crossing detection, Intrusion detection, Motion detection, Scene change detection, Face capture, Region entrance detection, Region exiting detection, Video tampering, audio exception detection, Focus on human and vehicle targets classification based on deep learning UL, CE, FCC certified. as per detail specifications and Preferred makes enclosed in rfp

Supply , Installation , Testing and commissioning of4 MP IR Outdoor PTZ Camera with 32X: 1/1.8" Progressive Scan CMOS, 2560 × 1440 at 25fps, 5.9 mm to 188.8 mm, 32× Optical, 16x digital zoom, Color: 0.005 Lux at F1.5, B/W: 0.001Lux at F1.5, ICR, support H.265, MJPEG, 120 dB WDR, 3D Digital Noise Reduction, HLC, BLC, Defog, Tripple individually configurable stream, 24 VAC & Hi PoE, IR range: 200m, Pan: 360° endless, Tilt: From -15° to 90° (auto-flip), Pan Speed - from 0.1°/s to 160°/s, Preset Speed: 240°/s, Tilt Speed- from 0.1°/s to 120°/s, Preset Speed: 200°/s, Presets- 300, Alarm Input-2-ch alarm input, Alarm Output-1-ch alarm output, Smart Tracking, Audio-1 channel input & output, 1 built-in speaker, Support on-board storage up to 256 GB, IP66, IK 10, Edge Analytics: Face Capture, Intrusion Detection, Line Crossing Detection, Region Entrance Detection, Region Exiting Detection, Video Tampering Detection, Motion Detection, Audio Exception Detection, UL, CE, FCC certified.

Switches

Supply , Installation , Testing and commissioning of 4 port Unmanaged Network PoE Switch: L2, Unmanaged, 4 Gigabit POE ports, 1 Gigabit RJ45 uplink port, 802.3af/at, PoE power budget 60w as per detail specifications and Preferred makes enclosed in rfp

Supply , Installation , Testing and commissioning of 8 port Unmanaged Network PoE Switch: L2, Unmanaged, 8 Gigabit POE ports, 1 Gigabit RJ45 uplink port, 1 Gigabit SFP uplink port, 802.3af/at, PoE power budget 58w as per detail specifications and Preferred makes enclosed in rfp

16 port Unmanaged Network PoE Switch: L2, Unmanaged, 16 Gigabit POE ports, 2 Gigabit SFP uplink ports, 802.3af/at, PoE power budget 125w as per detail specifications and Preferred makes enclosed in rfp

Supply , Installation , Testing and commissioning of 24 port Unmanaged Network PoE Switch: L2, Unmanaged, 24 Gigabit POE ports, 2 Gigabit SFP uplink ports, 802.3af/at, PoE power budget 225w as per detail specifications and Preferred makes enclosed in rfp

Supply , Installation , Testing and commissioning of 8 port Managed Network PoE Switch: L2, Smart Managed, 8 10/100M RJ45 PoE ports, 2 Gigabit combo ports, 802.3af/at, PoE power budget 125W, Max. 300 meter long distance PoE transmission, Supports Hik-Central/iVMS 4200/Hik-ProConnect Unified Topology Management, cloud management, health monitor, PoE watchdog, VLAN, QoS, SNMP, STP/RSTP, Port Mirroring, Storm Control as per detail specifications and Preferred makes enclosed in rfp

Supply , Installation , Testing and commissioning of 16 port Managed Network PoE Switch: L2, Smart Managed, 16 10/100M RJ45 PoE ports, 2 Gigabit combo ports, 802.3af/at, PoE power budget 230W, Max. 300 meter long distance PoE transmission, Supports Hik-Central/iVMS 4200/Hik-ProConnect Unified Topology Management, cloud management, health monitor, PoE watchdog, VLAN, QoS, SNMP, STP/RSTP, Port Mirroring, Storm Control as per detail specifications and Preferred makes enclosed in rfp

Supply , Installation , Testing and commissioning of Surveillance class Common Micro SD Card 128GB for camera- as per detail specifications and Preferred makes enclosed in rfp

Supply , Installation , Testing and commissioning of Hybrid SAN as per detail specifications and Preferred makes enclosed in rfp

Supply , Installation , Testing and commissioning of12 TB Enterprise HDD as per detail specifications and Preferred makes enclosed in rfp

Supply , Installation , Testing and commissioning of Video Management Software as per detail specifications and Preferred makes enclosed in rfp

Supply , Installation , Testing and commissioning of Server for Video Management Software as per detail specifications and Preferred makes enclosed in rfp

Boom Barrier Solution:

Supply , Installation , Testing and commissioning of Barrier Gate: Digital barrier gate, 4-6.0 s adjustable, straight boom pole, one device support left and right arm moving directions

Supply , Installation , Testing and commissioning of Anti-falling Radar: 79 GHz MMIC with higher resolution and more stable detection. Adopted with latest algorithm to filter the interference to radar from the advertising barrier, applicable to advertising barrier, fence, and straight boom pole. Able to recognize the target moving direction, applicable to mixed entrance and exit scenes. Adjustable detection distance and width with convenient operation and strong universality. Free of learning, applicable to more complex environments. Communication via RS-485 or Wi-Fi. Wi-Fi version is equipped with mobile phone application, with which you can debug and upgrade the radar with convenient operation.

Supply , Installation , Testing and commissioning of Capture-trigger Radar: 79GHZ, Beam width:Vertical 34°, Horizintal 12°, relay output

Supply , Installation , Testing and commissioning of ANPR Camera with Pole mounting brackets : Based on Deep-learning algorithm, ANPR, 4MP, 2688 × 1520 at 25fps, Color: 0.001 Lux at F1.2 & I/O trigger Local database s stores up to 100 thousand license items of blacklist and whitelist (TF card) 4-11 mm Lens, Auto-Iris, IR View Range of Camera Up to 50 m, Individual Tripple stream, H.265, H.264 Video Compression, Voice announcement and text output Relay output for barrier gate control Online & offline working mode Motorized zoom lens IP67 IK10 Vehicle type classification, color identification, no-plate vehicle capture, vehicle driving direction detection.along with Surveillance class Common Micro SD Card 128GB for ANPR Camera

Supply , Installation , Testing and commissioning of Software for Entrance & Exit Software

Baggage Scanner

Supply , Installation , Testing and commissioning of X-Ray Security Baggage Scanner:High performance with HD image, strong penetration, precise recognition,Adopts embedded L inux operating system with multi core ARM,Energy saving and environment protection with low power consumption,64X zoom in,With the popular tunnel size of 505mm W x303mm H, compact and movable design,Color/Black &White, local enhancement, high penetration, low penetration, super enhancement, inverse color, light increase, light reduce, grey scale scan, image zoom in, edge enhancement,One touch power off,User friendly interface for easy operation

Door Frame Metal Detector

Supply , Installation , Testing and commissioning of Digital Metal Detector Door: • 18 independent detection zones; • 11 kinds of working frequency available or manual setting from 7000 to 8999Hz, • Precisely detects passing passerby and alarmed passerby via infrared ray • Detects metal objects thrown through the door • Detects all metal objects more than 2cm above the ground •Detects multiple metals in different positions of the human body simultaneously • Distinguishes ferromagnetic from non-ferromagnetic metal objects • Anti-interference design, multiple inspection door working at the same time without mutual interference

Supply , Installation , Testing and commissioning of 4 port Unmanaged Network PoE Switch for DFMD: L2, Unmanaged, 4 10/100M RJ45 PoE ports, 2 10/100M RJ45 uplink port, 802.3af/at, PoE power budget 35W, max. 300m long distance transmission, 6KV surge protection

Supply , Installation , Testing and commissioning of Surveillance SD card 128GB for DFMD

Supply , Installation , Testing and commissioning of CAT-6 Cable in existing conduit with terminations

Emergency Call Box

Supply , Installation , Testing and commissioning of Box Panic Alarm Station: Adopts embedded Linux operation system and high-performance embedded SOC processor, 1920*1080 at 25fps, Supports H.265, H.264 video compression, WDR, HLC, TCP/IP, SNMP, HIK-SIP, RTSP, and ONVIF, 2 MP HD IR camera, Two-way audio, build-in high sensitive microphone, 1-ch Built-in Omnidirectional Microphone, 1-ch 3 W Build-in Loudspeaker, One-touch alarm, Tampering Alarm, 2 Ch I/O Input, 2 Ch I/O Output, Standard Micro SD card Slot, Supports Micro SD/SDHC/SDXC Card, Max. 128G, 1 Ch Siren, Power supply 100-240 VAC

Supply , Installation , Testing and commissioning of Software for Emergency Call Box

Class room Solution (For Lecture Theater 120 sitting and 60 sitting)

Supply , Installation , Testing and commissioning of Supports multiple recording & broadcasting modes, including cinema mode, PIP mode and resources (multi-screen) mode. Supports auto-directing to record the views of teachers and students Supports HDMI/VGA input to record PPT as per detail specifications and Preferred makes enclosed in rfp

Supply , Installation , Testing and commissioning of HDD based on requirement as per detail specifications and Preferred makes enclosed in rfp

Supply , Installation , Testing and commissioning of 1080P，Tracking teacher camera as per detail specifications and Preferred makes enclosed in rfp

Supply , Installation , Testing and commissioning of 1080P，student overview camera as per detail specifications and Preferred makes enclosed in rfp

Supply , Installation , Testing and commissioning of SI Scope and please purchase from local market. Audio Wireless RX、Wireless Audio Tx with Handheld Mic、Head Worn Microphone as per detail specifications and Preferred makes enclosed in rfp

Supply , Installation , Testing and commissioning of 86", 4K, Android 8.0, 4-core A73 × 2 + A53 × 2, 1.5 GHz, memory 3GB, build-in 32GB storage, build in Zoom, 20 points infrared touch contorl, industrial screen protection. Built-in Wi-Fi realizes wireless screen mirroring without any cable connection. Built-in interactive whiteboard system allows annotating and sharing. as per detail specifications and Preferred makes enclosed in rfp

Supply , Installation , Testing and commissioning of Wall-mounted Bracket, suitable for all models as per detail specifications and Preferred makes enclosed in rfp

Supply , Installation , Testing and commissioning of Switch HDMI Output signal of education sharing device, to USB signal. HDMI input and USB output，Output 4K+60fps，HDMI 2.0 as per detail specifications and Preferred makes enclosed in rfp

Supply , Installation , Testing and commissioning of Education Sharing Module Expansion Package - Including all functions of education sharing. as per detail specifications and Preferred makes enclosed in rfp

Supply , Installation , Testing and commissioning of Education Sharing Classroom Expansion Package Supported: 1 classroom manageable. Online classroom to share video & audio to remotely classroom, teacher appointments, good class video backup. as per detail specifications and Preferred makes enclosed in rfp

SITC of 86" Smart Interactive LED Panel for Class Room with Wall mount and 10m connecting cable as per detailed technical specifications enclosed in RFP and recommended makes, with 5 years warranty from dated of commissioning (For 60 seater, 30seater, Classrooms, Flip Classrooms, Tutorial rooms)

Video Wall Solution: 3 x 3

Supply , Installation , Testing and commissioning of 4K Video Wall Display : 46" LCD large screen, 1080P, Direct-lit LED backlight, VGA, HDMI, DVI, DP, USB input, Ultra-narrow 3.5 mm bezel design, 500cd/㎡, view angle : Horizontal 178°, Vertical 178°, RS232 IN × 1, RS232 OUT × 1, Active Display Area: 1018.08 (H) mm × 572.67 (V) mm, Operating temperature : 0 °C ~ 40 °C (32 °F ~ 104 °F), Storage Temperature: -20°C to 60°C (-4°F to 140°F), Along with wall mounting brackets as required for installation of video walls on existing wall complete in all respect per detail specifications and Preferred makes enclosed in rfp

Supply , Installation , Testing and commissioning of Decoder: Decoding 16-ch 12MP or 128-ch 1080P, 16; 10M/100M self-adaptive Ethernet interface, HDMI/BNC output, H.265/H.264+/H.264, 3*3 video wall control, Alarm: 8 Ch Input & 8 Ch Output, Two-Way Audio, 1 RS-232, 1 RS-485 AS per detail specifications and Preferred makes enclosed in rfp

Supply , Installation , Testing and commissioning of 7MTR HDMI Cable as per detail specifications and Preferred makes enclosed in rfp

Supply , Installation , Testing and commissioning of Software for Video Management Software as per detail specifications and Preferred makes enclosed in rfp

SWING BARRIER

Supply , installation , testing and commissioning of Acrylic wing material , Swing barrier with two-way Mifare Card. 650 mm passageway width. Left lane as per detail specifications and Preferred makes enclosed in rfp

Supply , installation , testing and commissioning of Acrylic wing material. Value series swing barrier with two-way Mifare Card. 650mm passageway width. Middle lane,as per detail specifications and Preferred makes enclosed in rfp

Supply , installation , testing and commissioning of Acrylic wing material. Swing barrier with two-way Mifare Card. 650mm passageway width. Right lane ,as per detail specifications and Preferred makes enclosed in rfp

Supply , installation , testing and commissioning of Swing Barrier Left Lane,as per detail specifications and Preferred makes enclosed in rfp

Supply , installation , testing and commissioning of Swing Barrier Right Lane, as per detail specifications and Preferred makes enclosed in rfp

Supply , installation , testing and commissioning of Mounting BASE-Single lane module, as per detail specifications and Preferred makes enclosed in rfp

Supply , installation , testing and commissioning of Mounting BASE-Expansion module, as per detail specifications and Preferred makes enclosed in rfp

Supply , installation , testing and commissioning of Face recognition terminal adopts deep learning algorithm, which helps to recognize the face faster and more accurate. It also supports multiple authentication modes: 1:N face match, 20,000 Face capacity,Event capacity ,100,000 , as per detail specifications and Preferred makes enclosed in rfp

Supply , installation , testing and commissioning of VMS license -E-Education-ACS-1 Door as per detail specifications and Preferred makes enclosed in rfp

Core to Distribution Network (Main Fiber Connectivity)

SITC of 96F Outdoor Armoured, Bend-Insensitive, Optical Fibre Cable, Singlemode fiber (G.652.D, G.657.A1, OS2) consisting of 8 loose tubes with 12 core each. Meet Standard Telcordia GR-20, IEC 60794-1. As per Technical Specifications. (For the Main Ring)

SITC of LCAPC to LCPC, Bend-Insensitive, Single Mode Fiber Patch Cord, 1.6 mm Duplex, LSZH Sheath as per IEC 60332-3, 15 Feet/5 meter, G.652.D & G.657.A1, OS2

SITC of 19" Rack Mount, 2U, 96 Core Fiber Splicing shelf, accepts (8), 8 modules or Adapter panels, Sliding modular Panel for 96 Core Fiber Termination

SITC of 360G2 Cartridge, 12 LCAPC, Single Mode, Green, Intelligent Ready

SITC of LCAPC to Unconnectorized, Fiber Pigtail, 0.9 mm, yellow jacket, 3 ft

SITC of Fusion Splices for 96 Core, 2U Shelf

SITC of LCAPC SCUPC SM, As per ITU-T G.657A(Bend Insensitive), Simplex Patchcord, Length 5 mtr

SITC of Fiber Splice Closure, 96F, with 4# splice tray, 2 round port seals, 1 Oval port seal, 96 SMOUV, IP 68 Rated.

SITC of 12 Core, Single Mode, Outside Plant, Dry core,Stranded Loose Tube, Metallic Armored, G.652.D & G.657.A1, OS2, Telcordia GR-20

SITC of 19" Rack Mount, 24F LIU, 1U Sliding shelf with 4 slots for accepts 4 Nos. of LC Single mode, OS2 Cassette/Adapter Plate.(For Residence)

SITC of 360G2 Cartridge, 12 Fiber LCAPC Style, Cassette Single Mode, Green, Intelligent Ready

SITC of LCAPC to Unconnectorized, Fiber Pigtail, 0.9 mm, yellow jacket, 3 ft

SITC of Fusion Splice Kit/Splice Trays, for 1U Shelf

SITC of 19" Rack Mount, 24F LIU, 1U Sliding shelf with 4 slots for accepts 4 Nos. of LC Single mode, OS2 Cassette/Adapter Plate. (For Departments)

SITC of 12 LCPC Cassettes/Adapter plate, Single Mode, Blue, Intelligent Ready

SITC of LC to Unconnectorized, Fiber Pigtail, 0.9 mm, yellow jacket, 3 ft

SITC of Fusion Splice Kit/Splice Trays, for 1U Shelf

SITC of LCPC to LCPC, Bend-Insensitive, Single Mode Fiber Patch Cord, 1.6 mm Duplex, LSZH Sheath as per IEC 60332-3, 10 Feet., G.652.D & G.657.A1, OS2

SITC of Fiber Splice Closure, 96F, with 4# splice tray, 2 round port seals, 1 Oval port seal, 96 SMOUV, IP 68 Rated.

SUPPLY FTTH BOQ FOR RESIDENTIAL COMPLEX

SITC of 19" RM Splitter with 4 Nos. of 1x2 splitter

SITC of SCAPC SC APC, As per ITU-T G.657A(Bend Insensitive), Simplex Patchcord, Length 3 mtr

SITC of 1U, 19 inches RM Splitter with 1 Nos. of 2x16 splitter

SITC of Street Cabinet/Fiber Distribution Cabinet, 96F with couplers, splice trays & panels. Fully loaded with SC APC Pigtails & adapters for all 24 Incoming core Fiber & 96 Outgoing Core Fiber. Should have capability to manage 96 core (12 cores x 12 Loose tube), fiber (incoming & outgoing) - 1 Nos. of 96 core Cables, with proper fasters & cable management. Should have option for Locking the enclosure, swing out front panel, should have 4 Nos. of 24F Splice tray, IP55 rated, water & Ingress resistant, preinstalled with canopy..

SITC of 2 x 32 Splitter, Plug-and-Play Splitter Module with SC/APC Connectorised, compatible with FDC

SITC of 2 x 16 Splitter, Plug-and-Play Splitter Module with SC/APC Connectorised, compatible with FDC

SITC of 12 Core Outdoor Armoured Cable, Gel-free, Bend-Insensitive, Optical Fibre Cable, Singlemode fiber (G.652.D, G.657.A1, OS2).

SITC of 6 Core, Single Mode, Outside Plant, Dry core,Stranded Loose Tube, Metallic Armored, G.652.D & G.657.A1, OS2, Telcordia GR-20

SITC of Optical Fiber Access Terminal, 24 F, Splice Only, IP 65 Rated.

SITC of Optical Fiber Access Terminal, 6 F, Splice Only, IP 65 Rated.

SITC of 2 Core, Armoured Drop Cable 9/125 µm SM-OS2, As per ITU-T G.652.D and G.657.A1(Bend Insensitive) CABLE

SITC of HFTP with 2# SCAPC Pigtail and Coupler

SITC of SC APC SC UPC SM, As per ITU-T G.657A(Bend Insensitive), Simplex Patchcord, Length 3 mtr

Distribution to Access, Multi Mode(OM4) Network (Fiber Connectivity)

SITC of 6 Core, Multi Mode(OM4) Indoor/Outdoor Low Smoke Zero Halogen Riser Distribution Cable, 6 fiber single-unit, Meet Standard ANSI/ICEA S-83-596 /Telcordia GR409

SITC of 19" Rack Mount, 48F LIU, 1U Sliding shelf with 4 slots for accepts 4 Nos. of LC Multi mode, OM4 Cassette/Adapter Plate.

SITC of 12 LC Cassettes/Adapter plate, Multi Mode(OM4), Aqua, Intelligent Ready

SITC of LC to Unconnectorized, Multi Mode(OM4) Fiber Pigtail, LSZH Sheath, yellow jacket, 3 ft

SITC of Fusion Splice Kit/Splice Trays, for 1U Shelf

SITC of 19" Rack Mount, 12/24F LIU, 1U Sliding shelf with 4 slots for accepts 4 Nos. of LC Multi mode, OM4 Cassette/Adapter Plate.

SITC of 12 LC Cassettes/Adapter plate, Multi Mode(OM4), Aqua, Intelligent Ready

SITC of LC to Unconnectorized, Multi Mode(OM4) Fiber Pigtail, LSZH Sheath, yellow jacket, 3 ft

SITC of Fusion Splice Kit/Splice Trays, for 1U Shelf

SITC of LC to LC, Bend-Insensitive, Multi Mode(OM4) Fiber Patch Cord, 1.6 mm Duplex, LSZH Sheath as per IEC 60332-3, 10 Feet.

Cat 6A U/UTP, Copper Cabling BOQ for Departments at Fintech Digital University, Campus

SITC of 10G, ETL Verified Category 6A U/UTP Cable, White jacket, 4 pair count, LSZH Sheath as per IEC 60332-3-22,

SITC of Category 6A U/UTP Loaded Patch Panel, 24 port, Intelligent Upgradable

SITC of Cat 6A-10G, Solid Low Smoke Zero Halogen as per IEC 60332-3-22, Cordage Modular Patch Cord, BLUE Jacket, 3 Feet (At Rack ends)

SITC of Cat 6A, 10G Information Outlet, Color BLUE (At User ends)

SITC of Cat 6A-10G, Solid Low Smoke Zero Halogen as per IEC 60332-3-22, Cordage Modular Patch Cord, BLUE Jacket, 10 Feet (At User ends)

SITC of 3*3, Square faceplate Dual port with Shutter(At User ends)

SITC of 3*3, Square faceplate One port with Shutter(At User ends)

SITC of Cable Management Panel, horizontal, 1U, black (At Rack ends)

Cat 6A Copper Outdoor Shielded Cable & Other Accessories for OUDOOR

SITC of Category 6A F/UTP Cable, outdoor, Black jacket, Aluminum tape shield, inner jacket, 4 pair count, 1000 ft (305 m) length, reel

SITC of Category 6A F/UTPHigh Density F/UTP Modular Panel, 24-port

SITC of Cat 6A Jack Shielded High Density Information Outlet (Rack Side)

SITC of Cat 6A S/FTP Low Smoke Zero Halogen Cordage, S/FTP Modular Patch Cord, Black Jacket

SITC of Cat 6A Jack Shielded High Density Information Outlet (User Side)

SITC of Outdoor Outlet Cover, single gang, two ports Faceplate, IP 67 Rated

SITC of CAT 6A, F/UTP, Outdoor Rated Patch Cord Modular Patch Cord, Black Jacket

ADDITIONAL ITEMS

SITC of 40mm PLB HDPE Duct/Pipe (Inside Permanently Lubricated Silicore Inner layer) Inner Diameter- 33 mm & 6 KG Pressure rating or more for Fiber Optic Cable laying (BLUE color)

SITC of HDPE Push Fit Duct Coupler for jointing two HDPE ducts for 40 MM HDPE Pipe, Totally Air Tight, Water Tight and Leak Proof (Note: Jointing Coupler should be make from same OEM of HDPE Pipe)

SITC of Fiber cable Route marker- Outdoor

Excavation of 30cmx75cm size trench, 25 cm thick under layer of sand,IInd class bricks covering, refilling earth,compaction of earth, making necessary connection, testing etc. as required of size. For fibre laying

SITC of Pre-cast Concrete Conical Manhole, a ready to use / install chamber for connections, repeaters etc. in underground Ducting. Height - 1225mm. Base Diameter - 1350mm. Top Opening - 780 mm. Height of each ring - 225 mm. Thickness of each ring - 52 mm. Material Used M 30 Grade Concrete., Reinforcement: In the rings: 2 nos. of TMT Steel horizontal rings of size 8mm @ 250 mm c/c supported by 8mm TMT Steel bars. In the top ring 2 nos. of TMT Steel horizontal rings of size 8mm @ 150 mm c/c supported by 8mm TMT Steel bars. In top Cover: Multiple nos. of TMT Steel bars both ways in two layers. The Top Cover guarded by Galvanized (Optional) M S Plate and provided two 16 mm hooks for lifting. Load Bearing Suitable for an ultimate load of 35 tons (E.H.D. Cover Load as per ISI: 12592 Specifications).

SITC of ISI Mark "B" Class 50 MM GI Pipe for Drain/bridge Crossing/Road Crossing/entry to building with suitable Fixing (Make Jindal/Prakash/Surya)

SITC of 25MM, ISI Mark, PVC Conduit with Fixing accessories, Including Conduit Bends

SITC of 32MM, ISI Mark, PVC Conduit with Fixing accessories, Including Conduit Bends

SITC of 40MM, ISI Mark, PVC Conduit with Fixing accessories, Including Conduit Bends

SITC of 32mm Flexible Pipe with Steel Armouring for Outdoor Laying

SITC of 25/32 mm PVC Flexible Pipe

SITC of 25 mm GI Flexible Pipe

RACKS

SITC of 42U Closed Network Rack with front glass door, rear steel Double door, 800mmx1000mm, castor wheels, 2 Equipment Shelf, 15 Amp, AC power supply Vertical with 10 sockets- 2 nos, 4 fans at top Mounted, earthing kit and Mounting Accessories.

SITC of 24U/27U Closed Network Rack with front glass door, rear steel Double door, 800mmx800mm, castor wheels, 2 Equipment Shelf, 15 Amp, AC power supply Vertical with 10 sockets- 2 nos, 4 fans at top Mounted, earthing kit and Mounting Accessories.

SITC of 15U wall mount Closed Network Rack with front glass door, 600mm x 600mm Depth, 5 Amp, AC power supply Horizontal with 5 sockets- 2 nos, 2 fans at top Mounted, 1 Cantilever shelf, earthing kit and Mounting Accessories.

SITC of 9U wall mount Closed Network Rack with front glass door, 600mmx 600mm Depth, 5 Amp, AC power supply Horizontal with 5 sockets- 2 nos, 2 fans at top Mounted, 1 Cantilever shelf, earthing kit with Mounting Accessories.

GPON EQUIPMENTS

SITC of GPON 8 Port OLT, 4GE+4SFP+,Dual PS, (With PON SFPs)

SITC of XPON ONT 2GE+1POTS+ WIFI DUAL BAND(2.4G+5G)

Active Items (Phase Wise)

Core Switch: Supply , installation , Testing and Commissioning of Core Switch 32* 40/100G Port switch populated with 8*100G Single Mode SFP's with 5 yrs Warranty as per detailed specifications and Prefered make

Distribution Switch: Supply , installation , Testing and Commissioning of Distribution Switch 48* 1/10/25G Port switch with 6*40/100G Uplink ports populated with 48*25G LR SFP & 2*100G Single Mode SFP's with 5 yrs Warranty as per detailed specifications and Prefered make

48 Port Access Switch POE: Supply , installation , Testing and Commissioning of Access Switch 48 Port PoE+ switch with 2*25G Uplink ports populated with 25G LR SFP with 5 yrs Warranty as per detailed specifications and Prefered make

24 Port Access Switch POE: Supply , installation , Testing and Commissioning of Access Switch 24 Port PoE+ switch with 2*25G Uplink ports populated with 25G LR SFP with 5 yrs Warranty as per detailed specifications and Prefered make

SITC of Firewall with min. 20 million concurrent connections & 1 million connections/Sec capability, 15 Gbps threat protection throughput, 8 x 1GE RJ-45 interfaces and 8 x 10G SFP+ SR interfaces slot, 4x 100GE QSFP28/40GE QSFP slot network ports including management port, Unified threat protection, IPS Advance malware protection, Application control, Web and Video filtering, Antispam including web application firewall, ICSA and EAL4 certified.

AAA with LLB, quota management and captive portal: Supply , installation , Testing and Commissioning of Link Manager with minimum 8x10G ports, to manage minimum 4 internet links. Minimum 64 GB RAM, 4TB HDD, in high availability using standard VRRP and support open standards with 5 year warranty & support as per detailed specifications and Prefereed make

SSL VPN for remote access: Supply , installation , Testing and Commissioning of Remote Access Management with captive portal, WIFI quota management and AAA, with minimum 8 x 10G ports , 45M encrypted throughput, 2 FA, Google auth support and hardware binding using mac ID, HDDID, CPUID, OS related features, 64 GB RAM and 4TB HDD with 5 year warranty & support as per detailed specifications and Prefered make

Wifi Access Points (Indoor): Supply , installation , Testing and Commissioning of Indoor Wifi access point with 5 year warranty & support as per detailed specifications and Prefered make

Wifi Access Points (Outdoor): Supply , installation , Testing and Commissioning of Outdoor wifi access Point with 5 year warranty & support as per detailed specifications and Prefered make

Wifi controller software: Supply , installation , Testing and Commissioning of Wifi access point controller - Software based expandable upto 1000 with HA license with 5 year warranty & support as per detailed specifications and Prefered make

Smart Racks

Supply installation, testing and commissioning of integrated smart racks as per detail specifications enclosed comprising of 5 racks for servers and storage, network equipments, inbuilt precision air conditioning, Novac fire supression system, CCTV and DVR, LED lighting, IP based biometric access control system, rodent control system, UPS, fire alarm system, iPDUs for 3 phase/single phase supply as required (2 per rack), temperature and humidity monitoring, door switch and water leakage sensors, becon alarm,

Ahluwalia Contracts (India) Ltd.

Ramacivil India Construction Pvt. Ltd.

Ramacivil India Construction Pvt. Ltd.

Ashoka Buildcon Limited

Ramacivil India Construction Pvt. Ltd.

Ahluwalia Contracts (India) Ltd.

Ashoka Buildcon Limited

Ahluwalia Contracts (India) Ltd.

Ramacivil India Construction Pvt. Ltd.

Ahluwalia Contracts (India) Ltd.

Ahluwalia Contracts (India) Ltd.

Ramacivil India Construction Pvt. Ltd.

Ashoka Buildcon Limited

Ahluwalia Contracts (India) Ltd.

Ashoka Buildcon Limited

Ahluwalia Contracts (India) Ltd.

Ahluwalia Contracts (India) Ltd.

Ashoka Buildcon Limited

Ahluwalia Contracts (India) Ltd.

Ashoka Buildcon Limited

Ramacivil India Construction Pvt. Ltd.

Ahluwalia Contracts (India) Ltd.

Ramacivil India Construction Pvt. Ltd.

Ashoka Buildcon Limited

Ashoka Buildcon Limited

Ramacivil India Construction Pvt. Ltd.

Ashoka Buildcon Limited

Ramacivil India Construction Pvt. Ltd.

Ramacivil India Construction Pvt. Ltd.

Ahluwalia Contracts (India) Ltd.

Ahluwalia Contracts (India) Ltd.

Ashoka Buildcon Limited

Ramacivil India Construction Pvt. Ltd.

Ashoka Buildcon Limited

Ashoka Buildcon Limited

Ramacivil India Construction Pvt. Ltd.