ADDITION/ALTERATION AND SPECIAL REPAIRS OF MD ACCN AT MIL STN TALBEHET.

Amount

Note: (i) Please refer schedule 'A' notes before quoting the tender. (ii) Amount of Schedule of credit shall be deducted off line by the department.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for Non skid ceramic coloured tiles 7mm to 8mm thick (square/rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors, etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with & including 15mm thick screed bed in CM 1:4 complete all as specified and directed

M&L for Non skid ceramic coloured tiles 7mm to 8mm thick (square/rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in skirting, dados etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with & including 10mm thick rendering in CM 1:4 complete all as specified and directed.

M&L for Glazed ceramic coloured tiles 450mm x 350mm x 7mm thick, in vertical surfaces such as skirting, dados and risers to steps, etc set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with & including 10mm thick rendering in CM 1:4 complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc complete all as specified and directed..

M&L for Brushing neat cement slurry with 3 Kg of cement per square meter complete all as specified and directed.

M&L for Machine cut Kota stone slab flooring 20-25mm thick (size not less than 450mm x 600mm) with and including 20mm thick cement screed base in CM 1:3, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and mirror polishing complete all as specified and directed. Note:- All exposed edges of kota stone flooring shall be finished as half round/bull nosed as approved by GE.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons, walls, etc, laid bedded and pointed in any mortar complete all as specified and directed.

M&L for Marble (makrana white) work 18-20 mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms with and including 20mm thick cement screed base in CM 1:3 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and directed.

S&F Steel ventilators with top hung shutter including projecting type hinges, with steel handle, and steel peg stay, without glazing bars complete all as specified and directed.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, with glazing bars complete all as specified and directed.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, without glazing bars complete all as specified and directed.

S&F Mild steel conforming to Fe-290 Gde E-165 in framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted or forged into spikes; framed guard bars; ladders; railings and similar work complete all as specified and directed.

S&F Sheet glass 3mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed.

S&F Figured glass, pin head type 3mm thick and glazing with oil putty in squares not exceeding 0.5Sqm in each pane complete all as specified and directed.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

M&L for Preparing new or previously untreated steel & iron surfaces of any description over 10cm in width or girth and applying two coats of synthetic enamel paint over & including a coat of red oxide zinc chrome primer complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as specified and directed.

Taking down chowkats with shutters not exceeding 1.5 Sqm each (without taking off shutters from the frames) complete all as specified and directed.

S&F Pressed steel frames of size 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.

S&F Pressed steel frames of size 165mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.

M&L for factory made Second class hardwood 35mm thick plain, framed, panelled shutters (any number of panels) with panels of timber flat on both sides (feather edged) or of 12mm thick veneered particle board medium density, wood particle board with commercial face veneers sizes of members of shutters as specified in IS- 1003 (Part I, complete all as specified and directed.

S&F IInd Class hardwood 35mm thick factory made glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) supplied and fitted to chowkats complete all as specified and directed.

S&F in repairs Sheet glass 3mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed.

M&L for Cement concrete 1:3:6 type B1 using 20 mm graded stone aggregate in filling of pressed steel door frames, holdfast, etc complete all as specified and directed.

S&F Factory made solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified and directed.

S&F Butt hinges, extruded aluminium alloy with galvanized mild steel hinge pin, anodized, type C-21 , 100 mm size complete all as specified and directed.

S&F Mild steel barrel tower bolts, stove enamelled black, with bright bolt, 200 mm long complete all as specified and directed.

S&F Mild steel sliding door bolts 300mm long, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed.

S&F Extruded aluminium alloy handles, fabricated type, anodised, 125 mm size complete all as specified and directed.

S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor; overall length of cover plate 150mm complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer all as specified

Complete removal of existing treatment on walls (any number of layers) by scrapping with steel scrappers or any other means including filling depressions of scrapped surfaces with putty and preparation of surfaces for further treatment and M&L for applying two coats of distemper oil emulsion, white or tinted over a oat of alkaline base primer complete all as specified and directed.

M&L for preparing old decorated plastered or unplastered surfaces of ceilings and applying two coats of white wash complete all as specified and directed.

Complete removal of existing treatment on walls (any number of layers) by scrapping with steel scrappers or any other means including filling depressions of scrapped surfaces with putty and preparation of surfaces for further treatment and M&L for applying two coats of cement base paint , white or tinted complete all as specified and directed.

M&L for Preparing old painted surfaces of wood and wood based materials of any description over 10cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

S&F in repairs 15mm bore angular stop valves with wall flange, half turn / quarter turn, fancy type chromium plated screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repairs 15mm bore bib tap, foam flow with flange, half turn/ quarter turn, fancy type chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for brass ferule and fixed complete all as specified and directed.

S&F half turn / quarter turn, 15mm dia CP central hole basin mixer without pop up waste system with and including 2 Nos. 450 mm long flexible heavy duty PVC connection suitablr for mixing of hot and cold water screwed for iron pipe and fixed complete all as specified and directed.

S&F half turn /quarter turn chromium plated 15 mm bore wall mixture 2 in 1 with provision for over head shower with 115 mm LB pipe & wall flange complete with bend pipe and wall flange, complete all as specified and directed.

S&F in repairs brass Chromium plated shower rose 125 mm size with or without swivel joints any size including fixing of steel pipe or unioncomplete all as specified and directed

S&FSoap dish disc (oval) type, mild steel Chromium plated of approximate size 100 x 50 x 10 mm complete all as specified and directed

S&F in repairs brass chromium plated towel rail 20mm dia D type 60cm long between flange complete all as specified and directed

S&F in repairs sheet glass assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated brackets guard and railing 60cm long complete all as specified and directed.

S&F in repairs hand shower (health faucet) with 8mm dia 1.0 mter long flexible tube and wall hook complete all as specified and directed.

S&F in repairs corner glass shelf assembly consisting of 5.5 mm thick sheet glass shelf with chromium plated bracket guard and railing complete all as specified and directed.

Taking up or down steel tubing and connections 15 mm bore complete all as specified and directed.

Taking up or down steel tubing and connections 20 mm bore complete all as specified and directed.

S&F 16mm CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings fixed complete to walls, ceilings or in floors, etc complete all as specified and as directed.

S&F 20mm CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings fixed complete to walls, ceilings or in floors, etc complete all as specified and as directed.

M&L for Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, shelves, lintels, etc, and cutting chases for concealed water tubings, etc and making good, cutting not exceeding 10cm girth complete all as specified and directed.

S&F in repairs Vitreous china squatting pan ‘Orissa’ pattern, size 580 x 440 mm ISI mark, white with integral foot rests including provision of cement concrete bedding & ‘P’ or ‘S’ trap complete all as specified and directed.

S&F PVC low level flushing cistern 10 liters capacity dual flush, ISI marked, white, with all fitting and fixtures including brackets and 32 mm bore PVC flush pipe, complete all as specified and directed.

S&F PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F in repairs Vitreous china wash basin, ISI marked, white, flat back, size 550 x 400mm, including CP waste coupling, 32mm dia PVC waste pipe of suitable length, brackets and cutting for and pinning in ends of brackets, complete all as specified and directed.

S&F in repair bevelled edge looking mirror 5.5mm thick of size 60cmx 45cm mounted on commercial plywood 6 mm thick including PVC beading all round and fixed to wooden plugs with chromium plated screws complete all as specified and directed.

S&F Waste fittings, 32 mm bore, brass, chromium plated for glazed ware sinks, basins, etc with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

Taking down rain water pipes ( any size or pattern) incl all fittings, shoes, bends, swan neck etc. complete all as specified and directed

S&F PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed to walls, 110mm bore including clamps complete all as specified and directed.

S&F PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed to walls, 75mm bore including clamps complete all as specified and directed.

S&F PVC (SWR) bends any radius, 75 mm bore, provided with access door complete all as specified and directed.

S&F PVC (SWR) bends any radius, 110 mm bore, provided with access door complete all as specified and directed.

S&F PVC (SWR) bends any radius, 75 mm bore complete all as specified and directed.

S&F PVC (SWR) bends any radius, 110 mm bore complete all as specified and directed.

S&F PVC (SWR) branch pieces, single (single Y) equal or unequal, 110mm bore complete all as specified and directed.

SS&F PVC (SWR) junction single (single T), equal or unequal, 110mm bore complete all as specified and directed.

S&F PVC (SWR) vent cowl, 110mm bore complete all as specified and directed.

S&F PVC (SWR) branch pieces, single (single Y) equal or unequal, 75mm bore complete all as specified and directed.

S&F PVC (SWR) vent cowl, 75mm bore complete all as specified and directed.

S&F Sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including supply & fixing cantilever brackets of mild steel angle 35 x 35 x 5 mm and connecting union to pipe overall size:- 914mm x 460mm, bowl size:- 405mm x 330mm x 160mm, including CP waste coupling and 32mm dia PVC waste pipe of suitable length complete all as specified and directed.

S&F Grating doom 125 mm dia with waste hole of PTMT (Minimum weight 40 gms) complete all as specified and directed.

S&F Prelaminated particle board 18/19 mm thick, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

M&L for Plain fillets of second class hard wood, square or rectangular in section, clean sawn, secured with nails or brads; sectional area exceeding 6 Sqcm but not exceeding 13 Sqcm complete all as specified and directed.

S&F in repair decorative mild steel chromium plated, 19mm dia, minimum thickness 1mm, curtain rod with side fixing brackets complete all as specified and directed.

S&F Hasp and staple 100 mm size, mild steel, wire type, stove enamelled black, including bolt to hinge plate, fixed with screws complete all as specified and directed.

S&F fancy nob for curtain rod suitable to fix to curtain rod complete all as specified and directed.

Dismantling water tanks of capacity exceeding 250 litres but not exceeding 500 litres complete all as specified and directed.

S&F Rotational moulded (three layered, ISI marked) polyethylene water storage tanks (cylindrical vertical with closed top) of 500 litres capacity including PVC cover, hoisted and fixed in position including connecting up pipes complete all as specified and directed.

S&F Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of 20 mm bore (minimum weight 210 gms) complete all as specified and directed.

Demolition of un-reinforced concrete, etc in ground floors and paving n exc. 15cm thickness (below or above ground level) and removal of rubbish beyond defence land complete all as specified and directed

Demolition of concrete of any description and in any position not oterwise specifically provided for complete all as specified and directed.

M&L for Cement concrete 1:3:6 type C2 using 40mm graded stone aggregate in plinth protection, 75mm thick, finished even and smooth without using extra cement, including making joints to the full depth of PCC at every 3 meters and fixing glass strip (glass strip to be measured and paid seperately) at every change of direction complete all as specified and directed.

S&F Glass dividing strips, 3mm thick and 38mm wide, inserted in position in floors complete all as specified and directed.

M&L for rendering 15mm thick in in cement mortar 1:3 on faces of brick work or concrete surfaces; mixed with water proofing compound as per manufacturers instructions (water proofing compound to be measured & paid separately as supply only) and finished even and smooth without using extra cement complete all as specified and directed.

M&L for providing cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate in leveling course, slope correction, roof kerbs, etc finished even & rough mixed with water proofing compound as per manufacturers instructions (water proofing compound to be measured & paid separately as supply only) complete all as specified and directed.

M&L of water proofing treatment to toilet area of sunken floor complete all as specified and as directed with following course of description below:- (a) Applying first layer of cement slurry @ 0.488Kg/Sqm mixed with acrylic based polymer modified cementation composite compound coating @ 0.253Kg/Sqm of make as approved in technical instruction 5/2003 and be allowed to air cure of 4 Hours. (b) Second layer of cement slurry @ 0.242Kg/Sqm mixed with acrylic based polymer modified cementation composite compound coating @0.126Kg/Sqm and be allowed to air cure of 4 Hours. (c ) Followed with water curing and testing for leak proof by ponding test for 48 Hours

M&L for Cement concrete 1:5:10 type E-2 using 40mm graded stone aggregate in foundations, sub base floor, filling and mass concrete complete all as specified and directed.

M&L for 50mm dia light grade GI pipe as in spout to drain out if any leakage occures in the sunken portion complete all as specified and as directed

Supply only liquid integral water proofing chemicals complete all as specified and directed.

Demolition of brick work or stone /boulder masonary built in cement or cement lime mortar complete all as specified and directed.

M&L for Brick work with fly ash bricks (Modular), straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

Taking down cement or cement lime plaster, any description, on brick or stone walls, ceilings, etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1: 6 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1: 4 on fair faces of brick work or concrete surfaces, finished fair and even complete all as specified and directed.

M&L for Rendering 5 mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even and smooth without using extra cement complete all as specified and directed.

Preparing new plastered or un-plastered surfaces of wall and M&L for applying two coats of distemper oil emulsion, white or tinted over a coat of primer complete all as specified and directed.

Preparing new plastered or un-plastered surfaces of wall and M&L for applying two coats of cement base paint, white or tinted over a coat of primer complete all as specified and directed.

M&L for preparing new plastered or unplastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

Taking down existing old roof treatment of any description, type and in any position including removal of old tiles, screed, felt, etc complete all as specified and directed.

M&L for Water proofing treatment on roof surfaces with APP modified membrane with non woven polyester reinforced, weight not less than 3 KG/SQM and thickness of membrane not less than 3mm having thermal insulation with white mineral/gravel finish on upper side of membrane uniformly embedded during manufacturing process laid in following sequence complete all as specified and directed.:- (a) Applying 10mm thick plaster in CM 1:4 mixed with and including water proofing compound @ 3% by weight of cement on cleaned roof surface. After properly curing of the plaster, the roof will be tested for water tightening by ponding with water for seven days for any seepage/leakages, etc. If any seepage/leakage is observed the rectification will be carried out by pressure grouting under pressure of 5 Kg/sqcm using cement based grout. After the roof surface is repaired, the slab /roof will be again tested for water tightness before proceeding for further treatment. (b) Properly cleaning and drying of the plastered roof surfaces, parapets, gutters, drain mouths, etc for all foreign matters such as fungus, moss, dust, etc by wire brushing and dusting. Proper grooves shall be cut around CI drain outlets/pipes/chimney pipes and other similar situations to tuck in the treatment. (c) Applying a coat of bituminous primer conforming to IS: 3384-1965 @ 0.4Kg/Sqm on the prepared surface till the surface is properly impregnated. (d) Laying APP modified water proofing membrane with 100mm overlap in longitudinal direction and 150mm overlap in transverse direction sealed and bounded to the surface by torch application method.

BOQ Serial Item No.102.00 (contd/-):- (e) All joints and changes in direction should be curved with cement mortar 1:3 with SBR latex @ 200ml per bag of cement and cured well before laying the membrane. A fillet of PCC 1:2:4 type B0 using 12.5mm graded stone aggregates shall be provided at all junctions of vertical and horizontal surfaces and wherever there is change of direction. (f) Applying one coat of Bituminous alluminium paint @ 0.20 Kg/Sqm over APP membrane. NOTE:- (i) Work of water proofing treatment shall be carried out by the authorised applicator of the manufacturer. Necessary documentary evidence in support of the authorised applicator will be submitted toGE before the commencement of water proofing work. (ii) The quoted rates is deemed to include for the cost of scaffolding, T&P, etc required for execution of the work.

Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc or not exceeding 10 Sqm on plan and not exceeding 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in excavated approved soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm each complete all as specified and directed

Removing excavated soil to a distance exceeding 250m and not exceeding 500m and depositing where directed. at a level not exceeding 1.5m above the starting point complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in foundation bed of manhole, mass concrete, etc complete all as specified and directed.

M&L for Providing cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in cills, seismic and other similar bands, plinth courses, copings, bed plates, bond stones, etc including weathering, slightly rounded or chamfered angles and throating as directed including necessary form work complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:4 on any faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for Providing precast reinforced cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in cover slabs (for manholes etc), shelves and similar articles with plain faces including necessary moulds and setting in cement mortar 1:4 complete all as specified and directed.

M&L for mild steel TMT bars 6-8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia. or securing with clips complete all as specified and directed.

S&F Cast iron (spun) soil, waste and vent pipes, in any length with or without ears, with cement joints, laid in trenches or in floors, 100mm bore complete all as specified and directed.

S&F Cast iron branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, 100mm bore with cement joints complete all as specified and directed.

S&F Cast iron (spun) soil, waste and vent pipes, in any length with or without ears, with cement joints, laid in trenches or in floors, 75mm bore complete all as specified and directed.

S&F Cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) 75mm bore with cement joints complete all as specified and directed.

M&L for Concrete bed to drain pipes 150mm bore including packing under and haunching against the sides of pipes after they are laid and tested; in cement concrete 1:4:8 type D2 using 40mm graded stone aggregate complete all as specified and directed.

Dismantling of Cast iron of any description jointed in cement mortar and taking out of trenches, if required complete all as specified and directed.

Demolition and breaking up drain pipes (SGSW, AC or RCC) of any diameter, set in cement mortar including fittings complete all as specified and directed.

S&F salt glazed stoneware drain pipes 150mm bore, grade ‘A’, laid in trenches and jointed as specified complete all as specified and directed.

M&L for septic tank of 100 users including excavation & earth work in any type of soil, foundation in PCC (1:2:4), brick work in CM (1:4), RCC ( M-25) slab cover including necessary man hole cover, vent pipe and sludge chamber, etc complete all as specified, directed and shown on drawing No CEBZ/TD/76/2011, Sheet- 1/2 to 2/2. Note :- All Excavations, returning filling and removing of surplus soil is deemed to be included in the quoted unit rate.

M&L for soakage wells of size 3.0m dia & 4.5m effective depth (suitable for 100 users) including excvation in any type of soil, foundation in PCC 1:3:6, wells of Honey combed and solid in M-25 Concrete, including intercepting chamber, screen chamber, Brick work in CM, RCC cover slab in M-25/ RR masonry / Filling with brick bats, complete all asspecified and shown in drawing No.CEBZ/TD/78/2011 Sheet 1/2 & 2/2. Note :- All Excavations, returning filling and removing of surplus soil is deemed to be included in the quoted unit rate.

Dismantling posts or struts (wood, steel or RCC), any section, including taking out embedded portion and making good disturbed ground; posts embedded in natural ground complete all as specified and directed.

Excavating in post holes (or similar holes) in hard dense soil each not exceeding 0.5cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering and removing surplus soil to a distance not exceeding 50m and making good surface complete all as specified and directed.

Dismanting of Barbed wire fencing or any type and size complete all as specified and directed.

M&L for Cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate in foundations, filling and mass concrete complete all as specified and directed.

S&F Rolled mild steel conforming to Fe-290 (Gde E-165) as in posts & struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc, complete all as specified and directed.

S&F mild steel round bars 10mm dia as stiffeners in chain link fencing etc, cut to length, including welding completed all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc including provision of binding wire complete all as specified and directed.

Supply only chain link mild steel galvanized fencing, any type or size complete all as specified and directed.

S&F Mild steel screw bolts (machine made) with hexagonal or square head at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exceeding 10cm but not exceeding 15 Cm long and dia of shank 06 to 10mm complete all as specified and directed.

S&F Framed work of rolled mild steel conforming to Fe 410-W (Gde E-250) quality -A as in doors or gates of angle or other section with gusset plates, rails, braces, etc, drilled for fixing of steel sheeting or other covering; and hanging, fastening & fixing including taking down old gate complete all as specified and directed.

M&L for Preparing new or previously untreated steel & iron surfaces of any description not exceeding 10cm in width or girth when unconnected with other painting or when painted in a different tint and applying two coats of synthetic enamel paint over & including a coat of red oxide zinc chrome primer complete all as specified and directed.

Taking down carefully existing point wiring (any type viz. aluminum or copper) with wooden batten/surface PVC conduit (with its fittings)/PVC casing-capping or any other type for light, fan, power point (including switch, socket, ceiling rose, etc.) and making good disturbed surface of wall/ceiling to match with existing surface after necessary rewiring complete all as specified and directed.

Taking down unserviceable sub main wiring including service connections, of any size and any description including wooden batten/conduit pipe, etc and making good disturbed surface of wall/ceiling to match with existing surface after necessary rewiring complete all as specified and directed.

M&L for point wiring with 1.5 Sqmm, PVC insulated, unsheathed, multi-stranded copper conductor single core FRLS cable, IS-694 marked, drawn through and including non metallic rigid PVC concealed conduit 20mm dia or higher by cutting of walls (brick or stone) and making good disturbed surface of wall in CM 1:3 (except on ceiling for fan point only, surface casing capping will be used in lieu of concealed PVC conduit) with all PVC conduit accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc./ fittings ISI marked and sunk type pressed steel anodised terminal box 1.2 mm thick with bakelite laminated sheet top cover 3 mm thick, brass screws and cup washers including 1.5 Sqmm multi-stranded copper conductor PVC insulated green in colour as continous earth conductor connected to common earth and earth dolly with all accessories complete all as specified and directed (Note- Lamp Holder & bell point earth continuity wire is not required) for:-

One light point/bell/ fan point controlled by one, one way switch.

One 5 pin 5 Amp socket on same board with other switches.

One 5 pin 5 Amp socket on independent board.

All as per BOQ Serial item No.131.00 but with 4.0 Sqmm, for one 5 pin 5/15 Amp socket on independent board including 4.0 Sqmm multi-stranded copper conductor (FRLS) PVC insulated green in colour as continous earth conductor connected to common earth complete all as specified and directed.

S&F sub main wiring with two runs of single core PVC insulated and unsheathed multistranded (FRLS) copper conductor cable of size 6.00 Sqmm LT, 1100 volts grade, drawn through and including 25 mm dia or higher PVC non metallic concealed conduit by cutting of walls (brick or stone) and making good disturbed surface of wall in CM 1:3 (except on ceiling for fan point only, surface casing capping will be used in lieu of concealed PVC conduit) with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 6 sqmm single core multistranded copper conductor cable green colour as earth continuity conductor complete all as specified and directed. Note : - Two run of single core cable, one run of earth continuity conductor shall be measured as one unit length..

S&F switch piano, flush type 5 amps, single pole, one way 240 volts complete all as specified and directed.

S&F switch piano, flush type 15 amps, single pole, one way 240 volts complete all as specified and directed.

BLANK

S&F socket outlet, 2 in 1, 3 pin & 2 pin, 5/6 Amps, flush type, 240 volts complete all as specified and directed.

S&F socket outlet, 2 in 1, 3 pin & 2 pin, 5 & 15 Amps, flush type, 240 volts complete all as specified and directed.

S&F stepped type, 80 to 100 watts electronic ceiling fan regulator flush type, AC, 230 volts, complete all as specified and directed. Note: Regulator and switch/socket will be of the same make

S&F ceiling rose, surface type bakelite, three terminals complete all as specified and directed.

S&F Bell ding dong type electric 230 volts AC, single phase, complete all as specified and directed.

S&F Bell push, flush type, 5 Amp piano type, 230 volt AC complete all as specified and as directed.

S&F lamp holder PVC/polycarbonate type with back plate complete all as specified and directed.

S&F PVC connector for ceiling fan complete all as specified and directed.

S&F in replacement tube light fitting LED 20/22 watt, 6000K, 230 volt, LED batten with epoxy powder coated extruded aluminium heat sink channel housing, cover made of high quality polycarbonate diffuswer for glare free light distribution, in-built electronic driver, bipin holders, connector block, etc complete with all accessories internally prewired and including connecting up with three core flexible copper conductor cable with suitable size for connection of fitting from ceiling rose complete all as specified and directed.

S&F MCB distribution board TPN, 4 way, 440 volts, double door (metallic type) with 200 Amps rated bus bar, neutral bar with shrouds, earth bar, IP-43, made out of sheet steel enclosure, recessed type, factory made powder coated suitable for housing MCBs as incomer and outgoing including blanking plate complete all as specified and directed. Note: MCB DB and MCB SP/SPN will be of same make.

S&F MCB distribution board single pole & neutral with 200 Amps rated bus bar, double door (metallic type), IP-43, made out of sheet steel enclosure, recessed type, factory made powder coated, 8 way, 240 volts suitable for housing MCB's including blanking plate complete all as specified and directed. Note: MCB DB and MCB SP/SPN will be of same make.

S&F MCB SP, 240 volt, 5 to 32 Amp capacity, 10 KA, 'B' curve complete all as specified and directed.

S&F MCB SPN, 240 volt, 20 to 40 Amp capacity, 10 KA, 'B' curve complete all as specified and directed.

S&F in replacement MCCB, 63 Amp, 4 Pole, 16 KA, 415 V, 50 Hz, fixed type with spread link in both side complete all as specified and directed.

S&F in replacement single pole and neutral enclosure with a two pin and earth plug and socket complete with and including one single pole 20 Amp MCB SP `B' series for geyser complete all as specified and directed.

Supply, fixing, connecting and testing of electric water heater (Geyser) stationary storage type, closed / vented type, vertical, including inner container of stainless steel, capacity 25 Ltrs, 240 volts, 2000 Watts heating element, 5 star ratting with two heavy duty PVC pipe Nylon braided connection (suitable for hot water), anchor fastner, nuts, bolts and washer etc, with power cable 6 Sqmm copper conductors complete all as specified and directed.

M&L for earthing complete with galvanized iron earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level connecting to GI strip 32 x 6 mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanized iron or steel and earth wire protected by 50mm dia GI pipe medium grade and connected to pole structure/ panel board/earthing test point all as shown in electrical plate No. 3 of SSR Part-I(2009) and testing on completion complete all as specified and directed. Note :- The unit rate quoted shall also include for excavation, earth work in any type of soil, plain cement concrete 1:3:6 mix, type C1 pit, 40mm thick RCC 1:2:4 mix type B1 cover reinforced with 8mm dia TMT bras @ 150mm C/C both ways, GI funnel with watering pipe, wire mesh, protection pipe, earth strip up to 7.50m long complete in addition to item No. 1(a) to (e) of preamble (Notes) under sub heading earthing, specified in SSR Part II ncluding 2.5sqmm multi stranded copper conductor PVC insulated, colour green to be provided as earth continuity wire drawn through consoled PVC conduit from test point to TPN DB.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m depth and getting in soft/disintegrated rock/hard dense soil for laying of cables, pole foundation, laying of pipe line, etc complete all as specified and directed.

Removing surplus excavated material to a distance not exc 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Taking up or down steel tubing and connections 25 mm bore complete all as specified and directed.

Taking up or down steel tubing and connections 40 mm bore complete all as specified and directed.

S&F Steel water tubes, medium grade, ISI marked, galvanised, 25mm bore with all fittings, fixed to walls and ceiling or laid in floors complete all as specified and directed.

S&F Steel water tubes, medium grade, ISI marked, galvanised, 40mm bore with all fittings, laid in trenches complete all as specified and directed.

Refixing old steel tubing 25 mm bore, with and provision of new fittings (connections) in new or old position (walls, ceiling, floors, etc) complete all as specified and directed.

S&F in replacement Gun metal globe or gate valves, conforming to IS 778 with butterfly handle, screwed both ends for iron pipe 25mm bore complete all as specified and directed.

S&F in replacement Gun metal globe or gate valves, conforming to IS 778 with butterfly handle, screwed both ends for iron pipe 40mm bore complete all as specified and directed.

Supply and laying in trenches, reinforced precast concrete cable cover, ISI marked, Class LV, Type- I, flat, size 300 mm x 180mm x 40mm for cable protection in trenches complete all as specified and directed.

M&L for sand filling with clean dry fine sand including gently punning around cables in trenches for cable protection (8 cm below cable & 15 cm above cable) complete all as specified and directed. Note:- Compacted/punned thickness shall be measured & paid.

S&F 40mm bore dia GI tubing light grade with all fittings as required for passing through cables under floors, along the wall or along the pole, etc with suitable size M.S.flat iron clamps incl nut,bolt and washer including taking down old rusted pipe complete all as specified and directed.

S&F Power Cables, Aluminum Stranded Conductor 25 sqmm, 3.5 core, XLPE Insulated, Cores laid up, PVC Inner sheathed, Armoured with galvanized wire or galvanized steel strip, overall PVC Sheathed, 1100V Grade as per IS 7098(Part 1) 1988 laid in trenches / floors / fixed to poles / walls / drawn through pipes, etc with and including provn of lugs, glands, nuts, bolts & washers, clamps, etc and testing on completion complete all as specified and directed.

S&F MCB SP, 240 volt, 63 Amp capacity, 10 KA, 'C' series for TPN DB 4 way complete all as specified and directed.

S&F LED Bulb 9 watts complete all as specified and directed.

M&L for writing letters or figures, Indian or Roman, size 100mm height using two coats of synthetic enamel paint complete all as specified and directed.

M&L for dots, commas, short line, dashed, hyphens, brackets, etc using two coats of synthetic enamel paint complete all as specified and directed.

Deduct schedule of credit (calculation will be done off line) Rs.3,37,450.00

GUPTA ENGINEERING WORKS

VIJAY BUILDERS

trading engineers

PARAS BROTHERS

M/S SHIVA TRADERS