Recalled for Renovation for washroom and pantry area of Ethics Committee room in Indira Gandhi Vidhya Bhawan North Block in University of Health Sciences Rohtak

Amount

Cement concrete 1:1-1/2:3 with stone aggregate 20 mm nominal size for reinforced concrete work in shelves excluding steel reinforcement, but including centering and shuttering ,laid in position ,complete in all respects. (HSR.10.81+10.95,a)

11.43 cm thick brick wall laid in cement sand mortar 1:4 in superstructure(HSR.11.48 a)

Providing and fixing PVC rain water pipe 6kg pressure of ISI mark in cement mortar during masonry work.(HSR 13.89)

(a) 100 mm dia PVC pipe 6 kg . Presure

Laying and fixing vitrified/ceramic anti skid tiles of any size of approved make in floor laid in any pattern as specified over a base of 20 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. (Tiles shall be supplied by the Department). (HSR 14.93)

Laying and fixing vitrified/ceramic/glazed tiles of any size of approved make in skirting/dado, pillars, wall facing, laid in any pattern as specified over base of 12 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. (Tiles shall be supplied by the Department). (HSR 14.94)

Laying and fixing granite stone in all shades, 15mm to 18mm thick in flooring, laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of granite stone (excluding the cost of granite stone) (HSR 14.96)

Painting two coats with synthetic enamel paint in all shades on old wood work or metallic or plastered or concrete surfaces to give an even shade including rubbing down old paint (HSR 16.5) L.R

Distempering with washable oil bound distemper (of approve manufacture) two coats on old distempered work.(HSR 16.60) L.R

Supplying and fixing hydraulic door closer, I.S.I. mark, with necessary screws, etc. complete- (H S R 17.82)

(c) I.S.I. designation No. III (size of door 851 mm to 1000 mm)

Providing and fixing sliding bolts with nuts and screws, etc., complete (HSR 17.83)

(a) brass

(i) size 300 mm x 16 mm

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to I.S.733 and I.S. 1285 fixed with rawl plugs and screws or with fixing clips or with expansion hold fasterners including necessary filling up of gaps at junction, at top, bottom and sides with required neoprene felt etc. aluminium sections shall be smooth, rust free straight mitred and jointed mechanically wherever required including cleat angle. Aluminium snap beading for glazing/panclling C.P. brass/stainless steel screws, all complete. Fixed portion (Anodised aluminium transparent or dyed to required shade according to IS:1868, minimum anodic coating of grade AC 15)(HSR 17.95)

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS :12823 grade I type II in panelling fixed in aluminium doors. Windows shutters and partition frames with C.P brass/stainless steel screws etc. complete.(HSR.17.97)

(b) Pre-laminated particle board with decorative lamination on both side.

Providing and fixing glazing in aluminium door windows, ventilator shutter and partitions etc. with pvc/neoprene gasket etc. complete (cost of aluminium snap beading shall be paid in basic items). (HSR.17.98) (b) With float glass panes of 5.0mm thickness.

Providing aluminum jali of thickness 7mm thick with opening 75mm x 75mm of including anodizing and fixing in frame with cost of screws etc. complete (HSR 17.100)

Providing and fixing aluminium round shape handle of cuter dia 100 mm with screws etc. complete (HSR 17.102)

(iii) Polyester powder coated minimum thickness 50 micron aluminium.

Steel reinforcement TMT bars FE-500 EQR / FE-500 D grade or more for RCC work, where no included in the complete rate of RCC including straightening, bending, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. and placing in position complete in all respects for all heights/depths/storeys/basements etc. (HSR 18.22). Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work, excluding overlaps. From the length so measured, the weight of reinforcement shall be calculated in tones on the basis of IS:1732.Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding and placing, shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement.

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall (DSR 18.10)

20 mm dia nominal bore

HSR ITEMS P.H WORK

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (to the approval of the Engineer-in-charge) EUROPEAN TYPE WATER CLOSET SUIT WITH NON-CONCEALED ‘P’ OR ‘S’ TRAP with or without vent and all other necessary fittings as fully described in item no.30.3 above.(HSR.30.4)

(i) White

Extra over item no.30.1 to 30.4 and 30.6 for providing and fixing 15 litres capcity low level vitreous china ware cistern complete with flush bend all other necessary fittings instead of C.I high level cistern complete with fittings.(HSR30.12)

(i) White

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (ORDINARY) LAVATORY SUITES consisting of Lavatory in VITREOUS CHINAWARE s ize as give below ( to the approval of the Engineer- in-c harge) including china plug for tap hole where necessary ; R.S. or C.I.BRACKETS for building into wall including painting;32mmC.P.BRASS WASTE WITH C.P. brass chain and rubber plug;15mm C.P.BRASS SCREW DOWN PILLAR TAP WITH jam nuts or couplings best design (as approved by the Engineer-in-charge) ALL FITTINGS BEST INDIAN MAKE and, to the approval of the Engineer-in-charge. All brass work chromium plated and complete in all respects including cutting and making good the walls floors and painting of fittings etc. (HSR.30.41)

White

(i) Size 450mmx300mm with one no. tap

Providing & fixing in position best Indian make towel rails fixed in with rawlslugs embeded in walls with C.P brass screws complete in all respect including cutting and making good the walls etc.(HSR.30.68)

(e) C.P brass towel ring

Providing and fixing in position best indian make bevelled edge.5.5 mm thick mirror mounted on asbestos sheet ground in position by means of 4 nos. chormium plated brass screws and washers over rubber washers and and rawl plug embedded inthe wall or cohormium plated brass clamps with C.P brass screws (as required by the Engineer-in-Charge) complete including cutting and making good the walls etc.(HSR.30.71)

(a) Indian Make

(i) 600mmx450mm

Providing and fixing in position C.P. brass stop cocks (as approved by the Engineer-in-charge) (HSR 30.76)

(a) 15 MM stop cock

(i) Stop cock male & female end