Provn of Paved area near Topchi Cinema, drainage system from MAP Ph-I (OR Md Accn) to Sem Nala and certain revenue/minor works under AGE B/R (M) at Faridkot Mil Stn

Amount

Excavation over areas not exc 1.5 mtr in deep and getting out in soft/loose soil complete all as specified and directed by Engineer in Charge.

Rolling and consolidating formation surfaces in cutting with 8 to 12 tonne power roller including filling in depressions which occurs during the process of rolling, rolling to required gradient and camber complete all as specified and directed by Engineer-in-Charge.

M&L for soling (or sub base) 150mm thick (in two equal layers of 75mm thick each rolling with 8 tonne to 12 tonne roller) with broken boulders or quarried stone, interstices filled, surface formed & rolled and consolidated to required gradient and camber complete all as specified and directed by Engineer-in-Charge.

M & L for cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in foundation, sub base & mass concrete complete all as specified and directed by Engr-In-Charge.

M&L for PCC 1:11/2:3, type A-2, using 40mm graded stone aggregate in two equal layers complete all as specified and directed by Engineer-in-Charge.

M & L for factory made pre-cast cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in solid blocks, exc 10cm in width and set in Cement Mortar 1:4 as in kerb stone including necessary form work, excavation and earth work for embedding kerb stone at a depth as directed & weathering / champhering temping around kerb stone and removal of surplus soil to a distance n.exc 50 metre & depositing where directed complete all as specified and directed by Engineer-in-Charge.

M&L for applying two coats of synthetic emulsion paint on concrete surface in different tint / shades complete all as specified and directed by Engineer-in-Charge.

M & L for forming contraction joints 65mm deep x 10mm wide filled with sealing compound Grade 'B' complete all as specified and directed by Engr-In-Charge.

M & L for forming expansion joints 20mm wide x 150mm thick filled with pre formed bitumen filler and top 30mm primed and sealed with sealing compound Grade 'B' complete all as specified and directed by Engr-In-Charge.

Excavation in trenches in soft loose soil not exceeding 1.5m deep and 1.5m wide, for foundation etc not exceeding 10 Sqm on plan and getting out complete all as specified and directed by Engr-In-Charge.

M & L for PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in foundation, filling & mass concrete complete all as specified and directed by Engr-In-Charge.

M&L brick work using sub class ‘B’ bricks old size brick in half brick walls built in cement mortar 1:4 straight or curved on plan exceeding 6m mean radius complete all as specified and directed.

M&L for brick work with fly ash bricks of old size straight or curved on plan exceeding 6m mean radius with old size bricks in wall built in cement mortar (1:4) complete all as specified and directed by Engr-In-Charge.

M&L PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregates as in coping of manholes, benching for manholes, bands, coping, bed plates including slightly rounded or chamfered angles including necessary formwork complete all as specified and directed by Engineer in Charge

M & L for rendering 10mm thick in cement mortar (1:4) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed by Engr-In-Charge.

M&L for flush pointing to brick walls in cement mortar 1:4 complete all as specified and directed by Engr-In-Charge.

M&L for extra for forming fair finish to drain or channel 150mm inner girth in cement concrete using extra cement including forms moulds/mitred and stopped ends, etc complete all as specified & directed.

M&L Precast PCC 1:2:4 type B1 (using 20mm graded stone aggregate) set in CM 1:4 as in manhole cover slab including necessary form work and placing as where directed complete all as specified and directed by Engineer in Charge

Demolition and breaking up drain pipes of any description, 300 mm dia set in cement mortar,including PCC haunching and disposal of rubbish to a distance but not exceeding 50M complete all as specified and directed by Engineer in Charge

S&F Reinforced concrete pipes class NP-2 laid in trenches, jointed and tested complete with collar of size 300mm (internal dia) complete all as specified and directed by Engineer in Charge.

M&L for PCC 1:4:8 type D-2 using 40mm graded stone aggregate concrete bedding to drain pipes including packing under haunching against the sides of pipe after laid & tested for 300mm bore of pipes complete all as specified and direced by Engineer in Charge.

M&L for TMT bars 5mm dia and over upto 10mm dia cut to length bent to shape as required, including cranking, bending and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed by Engr-In-Charge.

M&L for TMT bars of 10mm dia and over cut to length bent to shape required, including cranking and binding spirally for hooping from columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-In-Charge.

Demolition of brick work or stone boulder masonary, built in cement mortar or cement lime mortar including all quoins, pillars etc in any position and stacking them and disposing off the unserviceable material and rubbish complete all as specified and directed by Engineer in Charge.

Demolition of un-reinforced cement concrete of any description PCC in ground floor & paving (not exceeding 15cm below/above ground level) provided for complete all as directed by Engineer-in-Charge.

Returning, filling in including spreading, leveling watering and well ramming in layers not exceeding. 25cm thick each complete all as specified and directed by Engr-In-Charge.

Removal of surplus soil to a distance not exceeding. 50 m & depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed by Engr-In-Charge.

Taking down wooden/steel chowkhats or frames with shutters (without taking off shutters from the frames) of size not exceeding 1.50 Sqm each complete all as specified & directed by Engineer-in- charge.

Taking down wooden/steel chowkats or frame exc 1.5 sqm but n exc 4.0 sqm each but with shutters (without taking of shutters from the frame) complete all as specified and directed by Engineer-in-Charge.

S &F Pressed steel frames (1.25mm sheet thickness) for doors with one or more rebates including necessary fixing lugs , hinges, lock plate, etc., size of frame 105mm x 60 mm including one shop coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

S &F Pressed steel frames (1.25mm sheet thickness) for doors with one or more rebates including necessary fixing lugs , hinges, lock plate, etc., size of frame 125mm x 60 mm including one shop coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

Framed work such as grills, gratings,etc., with ends of bars shoulderd of bars and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe290, Gde-E-165 complete all as specified and directed by Engr-In-Charge.

S&F 35mm thick factory made 2nd class hard wood plain framed panel shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering both faces. The size of rail and style shall be as per IS:1003 (Part-I), klin seasoned and chemically presuure treated complete all as specified and directed by Engineer-in-Charge.

S&F 35mm thick second class Hard Wood glazed and skeleton shutters confirming to IS-1003 (Pt-1) open rebated and prepared to receive glass/gauze etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitered beads for securing glass etc sizes of members of shutter shall be as per SSR Pt –I section 8, clause 8.24 (a) complete all as specified and directed by Engineer-in-Charge.

S&F factory made box type steel window with side hung shutters including box type hinges with steel handle and 2 Nos 150mm long mild steel tower bolt,fixing lugs etc complete with glazing bars dovetailed or welded complete all as specified & directed by Engineer-in-Charge.

S&F factory made box type steel window with side hung shutters including box type hinges with steel handle and 2 Nos 150mm long mild steel tower bolt,fixing lugs etc complete without glazing bars dovetailed or welded complete all as specified & directed by Engineer-in-Charge.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but no baking) and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

S&F Glazed ceramic coloured tiles 450x300x7 mm thick as in vertical surfaces such as skirting/dados etc, set and jointed in neat cement slurry over & including 15mm thick rendering in cement mortar 1:4 and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed by Engineer-in-Charge.

M & L for 25 mm thick cement concrete (1:2:4) type B-1 using 20mm graded stone aggregates finished rough to receive glazed tiles complete all as specified and directed by Engr-In-Charge.

S & F Non skid ceramic coloured tiles light colour (as approved) 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry over & including 15 mm thick screed in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed by Engineer-in-Charge.

S &F Vitrified ceramic coloured (Coloured & shade as approved) tiles (square/rectangular) polished area of each tile of size 600x600x10mm as in floors etc set and jointed in neat cement slurry over & including 15 mm thick screed in cement mortar (1:6) and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed by Engineer-in-Charge.

S &F Vitrified ceramic coloured (Coloured & shade as approved) tiles (square/rectangular) polished area of each tile of size 600x600x10mm as in vertical surfaces such as skirting / dado etc set and jointed in neat cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed by Engineer-in-Charge.

S&F Anodised aluminium snap grid size of grid 605 x 605mm frame work for false ceiling complete all as specified and directed by Engineer-in-Charge.

S&F hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified and directed by Engineer-in-Charge.

S&F for providing Gypsum board 12mm thick fixed to metal frame work and reinforced with GI wire mesh (fillets, metal frame work and GI wire mesh paid separately) complete all as specified and directed by Engineer-in-Charge.

S&F PVC hollow wall lining interlocking type of 7mm thick plain/coloured fitted into the wall with PVC rawal plugs and steel screws including fillets to joints as per manufacturers instruction etc.complete all as specified and directed by Engineer-in-Charge. Note:- If any minor electric fittings and fixtures disturbed there will be match and fixed as existing.

Material and labour for preparation of new and previously un-treated steel surfaces of any description, not otherwise described over 10cmwidth or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed by Engr-In-Charge.

S&F factory made mild steel ventilators box type with sash bars dovetailed or welded ready for wire mesh/glass pan including one shop coat of red oxide primer, complete all as specified & directed by Engineer-in-Charge.

S&F figured glass 3.0mm thick pin head type and glazing with oil putty in squares not exceeding 0.50 sqm in each pane complete all as specified & directed by Engineer-in-charge

S&F galvanised mild steel wire cloth, 0.56mm nominal dia of wire average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed by Engineer-in-Charge.

S&F Solid wood grain printed PVC moulded door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube all as per SSR Part-II complete all as specified and directed by Engr-In-Charge. (Note : The material shall be of make Sintex/ Rajshri duly fabricated by thier authorised fabricator)

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width & stick inside with solvent cement for stile and plain colour PVC sheets for top rail lock rail and bottom rail on either side and as gap insert for top rail and bottom rail. Paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the style and rail with suitable PVC sheet beading and joined together with solvent cement supplying and fixing in the frame at site as per specifications & drawings as mentioned on Page 146 of SSR Part-II. (Note : The material shall be of make Rajshri/Sintex duly fabricated by their authorised fabricator.)

Supply & Fixing 100mm butt hinges medium weight, cold each rolled, mild steel complete all as specified and directed by Engineer-in-Charge.

S&F aluminium anodized tower bolts 150 mm long of extruded section fixed to doors with screws complete all as specified and directed by Engineer-in-Charge.

S&F aluminium anodized tower bolts 200 mm long of extruded section fixed to doors with screws complete all as specified and directed by Engineer-in-Charge.

S&F Aluminium anodized cast type handle 150 mm size complete all as specified and directed by Engr-In-Charge.

S&F 250 mm long aluminum alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy complete all as specified & directed by Engineer-in- charge.

S&F aluminium (Die cast) body door closer hydraulically regulated, designation No. 3 universal type, suitable for door shutters of 851 to 1000mm in width and weight between 61 to 80kg and fixed complete all as specified and directed by Engineer-in-Charge.

S&F vitreous china ware glazed wash hand basin white, flat back of size 550mm x 400mm including CI brackets, CP brass waste coupling with rubber washer and galvanized mild steel waste pipe 32mm bore complete all as specified and directed by Engr-In-Charge.

S&F vitreous china wash down water closet pan (pedestel pattern/EWC/longpan) white in colour including connection pipe to union of flushing cistern, inlet and overflow pipes,connecting only to flushing cistern anti-syphonage pipe with PVC flush pipe of 32mm dia and plastic seat cover with mild steel chromoum plated hinging and 'P' or 'S' trap device complete all as specified and directed by Engineer-in-Charge.

S&F in repair 15 mm fancy type chromium plated Angle valve/stop valve, screwed down high pressure,with crutch or butterfly handle scresed both ends for iron pipe or for unions and fixed complete all as specified and directed by Engineer in Charge.

S&F in repair 15mm bib taps, long body, chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engineer in Charge.

S&F in repair Pillar taps, cast copper alloy, with capstan heads, chromium plated,fancy type screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed by Engr-In-Charge.

S&F 15mm brass CP /basin mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed by Engineer in Charge.

S&F PVC connection 15mm dia 45 cm long with brass nut and washer both side complete all as specified and directed by Engr-In-Charge.

S&F in repair brass chromium plated shower rose 125mm size with or without swivel joints including fixing to steel pipe of 15mm bore complete all as specified and directed by Engineer in Charge.

S&F PTMT towel rail 450 mm long including brass screw and plastic cleat (Minimum weight 170 gms) complete all as specified and directed by Engr-In-Charge.

Taking up or down 15mm bore steel water tubing alongwith connections in any situation complete all as specified and directed by Engineer in Charge.

S&F Mild steel galvanized tubing 15 mm bore medium grade with fittings to walls with hooks, ceiling or laid on floor complete all as specified and directed by Engineer in Charge.

Re-fixing old steel tubing and connections in new or old position of wall ceiling or floor 15mm bore of pipe complete all as specified and directed by Engineer in Charge.

S&f Gun Metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed 15mm dia of pipe complete all as specified and directed by Engr-In-Charge.

M&L Soap shelf, PVC white/colour appx size 450 x 125 x 40mm (as per sample) complete all as specified and directed by Engineer-in-Charge.

S&F in repair chromium plated jet spray with 1.50 mtr long fexible tube including fixing arrangement complete all as specified and directed by Engineer in Charge. Make : Prayag Cat No. 522

S&F Toilet paper holder vitreous china fixed to walla with CP brass complete all as specified and directed by Engineer-in-charge.

S&F in repair rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 1000 Ltr capacity hoisted and fixed in position all as specified including PVC, 20mm bore ball brass valves, high pressure, with polythene float and fly nut screwed for 20mm bore iron pipe complete all as specified and directed by Engineer in Charge.

Dismantling CI/PVC pipe alongwith fittings 75/100mm bore, below or above GL, laid in floors or fixed to walls jointed in cement mortar and taking out complete all as specified and directed by Engineer in Chrge.

S&F 110 mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints, jointed with solvant and fixed to walls Cutting holes in brick wall built in cement mortar for inserting holdfasts, depth of embedded portion not exceeding half brick (measured from the face of jamb into the wall) complete all as specified and directed by Engineer-in- charge.

S&F 75 mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints, jointed with solvant and fixed to walls Cutting holes in brick wall built in cement mortar for inserting holdfasts, depth of embedded portion not exceeding half brick (measured from the face of jamb into the wall) and making good dismantled portion in cement mortor (1:3) or cement concrete (1:2:4) type B-I complete all as specified and directed by Engineer-in- charge.

S&F 110mm bore door type PVC (SWR) bends / shoe of any radius complete all as specified and directed by Engineer-in-Charge.

S&F PVC (SWR) 'P' trap of 125/110mm bore complete all as specified and directed by Engineer-in-Charge.

S&F PVC (SWR) 'P' trap of 75mm bore complete all as specified and directed by Engineer-in-Charge.

M&L PVC (SWR) Floor trap long neck 75 mm dia, with stainless steel grating including jointing to waste pipe fixed in cement concrete type B1, 1:2:4 complete all as specified and directed by Engineer in Charge.

S&F 75mm bore PVC(SWR) junction double Y (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed by Engineer-in- charge

S&F cast iron vent cowl 75mm pipe complete all as specified and directed by Engineer in Charge.

M & L for rendering 15mm thick in cement mortar (1:4) on brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed by Engr-In-Charge.

M&L for use and waste of form work to soffits of suspended slab such as roof slabs not exceeding 200mm thick horizontal or sloping complete all as specified and directed by Engr-In-Charge.

M&L 4mm dia galvanised steel wire, 150x100mm mesh, made up into mattresses or cages, lapped, wired and laid in position, including closing after filling complete all as specified and directed by Engr-In-Charge.

Surface excavation in soft/loose soil not exceeding 30 cm deep and averaging 15 cm deep and getting out complete all as specified and directed by Engr-In-Charge.

M&L for broken brick hard core of gauge not exceeding 63mm deposited, spread and leveled in layers not exc 15cm thick, watered and rolled/rammed to a true surfaces complete all as specified and directed by Engineer-in-Charge

M & L cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in sub base complete all as specified and directed by Engr-In-Charge.

M&L Sand filling under floors 25 mm thick complete all as specified and directed by Engr-In-Charge.

M&L machine pressed precast concrete interlocking paver block any shape and size confirming to IS-15658-2006 of 60mm thickness M-35 Grade with grey cement and pigment complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new concrete surfaces of any description, over 10 cm width or girth and applying two coats of plastic emulsion paint including priming paints complete all as specified and directed by Engineer-in-Charge. Note :- A Sum of Rs. 2,075.00 will be deducted on account of credit for dismantling/ demolished/ taking down material. Please refer detail on srl page No. 24 (Schedule of credit) of Tender Documents.

M/s Balvinder Singh Engineer and Contractors