Construction of Community Hall at Barbari Police Reserve, Baksa District, under Power Grid Corporation for the year 2020-21. (TN No.42_01).

Amount

COMMUNITY HALL 1.1. Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work. breaking clods in return filling, dressing , watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. (a)Up to depth of 2.00m below the existing ground level. (b)In ordinary soil

4.1.1. Providing soling in foundation and under floor with stone/best quality picked jhama brick, sand packed and laid to level and panel after preparing the subgarde as directed including all labour and materials and if necessary dewatering, complate. (a)Brick on flat soling

2.1.1. Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing, steps, walls, brick works etc. as directed and specified including dewatering if necessary and curing complete (shuttering where necessary shall be measured and paid separately). (b) In prop 1 cement: 3 sand :6 coarse aggregate by volume.

18.1.1. Suppling, fitting and fixing in position reinforcement bars conforming to relevant I.S code for RCC work/R.B walling including straightening cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) a) From primary producer TATA/SAIL/Esser steel/Jindal steel/ shyam steel/RINL (ii) super Ductile (SD) TMT reinforcement bars

C) I.S.I Approved Mild steel reinforcement bar (M.S Bar)

18.1.2 Extra over item 18.1.1(a,b,c) for each subsequent floor or part thereof above first floor level.

3.2.1. Providing from work of 12mm thick plywood Board so as to give a rough finish including centering, shuttering and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.00 M and removal of the same for in- situ rainforced concrete and plain concrete work in: 3.2.1.1. Column, pillars, post & strut of square/rectangular/polygonal in plan or any shape like Tee/L etc. having plane vertical face.

3.2.1.2. Sides and soffits of beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties. (a) For depth not exceeding 1.0M

3.2.1.3 Flat surfaces such as soffits of suspended floors, roofs, landings, cantilever slabs, chajjas,balconies and the like. (a) Floors etc.upto 200mm in thickness.

3.2.1.8 staircase with sloping or stepped soffits including risers and stringers but excluding landing.

3.2.4 Extra for each subsequent floor or part thereof above the first level as mentioned in item no.3.2.1 & 3.2.3.(b)

2.2.1. Providing & laying reinforcement cement concrete works in prop 1:2:4 (1 cement : 2 coarse sand : 4 coarse aggregated, 20 mm down ) including dewatering if necessary, and curing complate but excluding cost of form work and reinforcement for reinforced cement concrete work (from work and reinforcement will be measured and paid separately). (I) Using Mixture machine (a) In sub structure up to plinth level Foundation ,footing, columns with base, tie & plinth beam, pile ,cap, base slab, retainig walls, walls of septic tank inspection pit and the like and other works not less then 100mm thick up to plinth level. (b) M20 or Prop 1:1.5:3

(B) In super structure from plinth level up to 1st floor level. (ii) Columns, pillars, posts, struts, suspended floor, roof landing, shelf & supports, balcony, lintel, sill band, beam, girder, bressumer, cantilever, stair case (expect spiral stair case and landing) including preparing the top surface & finishing of nosing. (b) M20 or prop 1:1.5:3

2.2.3 Extra over item Nos.2.2.1 (I) (B) above for each subsequent floor or part thereof above the 1st floor level.

4.1.4. Brick work in cement mortar with 1st class brick including racking out joints and curing complate as directed. (I) In sub-structure upto plinth level including dewatering if necessary. c) In proportion 1:4

4.1.8. 1st class brick nogged wall in cement mortar including racking out joints and curing complate as directed in super structure above plinth up to 1 st floor level (protruding M.S Rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separately. (A) 112mm thick wall (a) In cement mortar in propportion 1:5 (1 cement : 5 sand)

4.1.14 Extra for brick walling for each subsequent floor or part thereof above the 1st floor level. (a) 112mm thick brick/ R.B wall

18.7.2 providing,fitting and fixing powder coated pressed steel door frame made of 1.25mm/1.6mm thick sheet of various sizes with necessary hinge jamb,lock jamb,head and steel base ties at the bottom of the frame.The whole frame shall be welded or rigidly fixed together by mechanical means with base ties of pressed mild steel angle of size 20X20X1.25mm thick.Frame to be filled up with 1:4:8 P.C.C after fitting the frame with brick/ concrete works etc.complate as directed by the department for all levels.(P.C.C to be measured and paid for speerately). (a) 1.25mm thick sheet (iii) size 125X60mm (single rebate)

9.12.1. Providing and fixing flush door shutters solid core construction with frame of 1st class hard wood with cross band and face veneered ply wood face panels conforming to relevent I.S code including oxidised iron butt hinges (100mm X 75mm X 3.5mm) 6 nos with necessary wood screws. (b) Non decorative type and block board core. (i) 35mm thick

11.1.1 Providing, fitting and fixing anodised aluminium windows and ventilators of standard sections of approved brand without horizontal glazing bars joints mitred and welded (manufactured to relevant IS specifications) fitted with 6mm X 3.15mm lugs 100mm long embedded in CC block 150mm X 100mm X 100mm in 1:3:6 mix including providing and fixing handles,frictions stays,joining cleat , bolting device,locking arrangement,spring catch as required complate as specified and directed for all levels.( Cement concrete to be measured and paid separately). a) side hung and top hung windows and ventilators (iii) 6mm coloured glass

12.3 Providing,fitting and fixing PVC door frame of Duroplast make DPF-5060 make suitable for DPS-3720 made from extruded PVC multichamber bollow section having dimension of 50mmX60mm (Toletance + 1mm). Horizontal and vertical section shall be joined by steel screws after inserting M.S tubular rectangular glavanised L-shaped brackets of size 100mmX100mm or plastic brackets of size 75mmX75mm with metred cut at the corners. Hinge side of the frame shall be reniforce with M.S tubular section of size 40mmX20mm. the frame will be fixed to the column/stiffner/wall with the help of 3nos 75mm long and 4mm dia steel screws and expandable fastners on each side of the door frame complate in all respects as sepcified and directed at all levels.

12.2 Providing,fitting and fixing 24mm/19mm thick polymer reinforced moulded PVC door shutters fixed to the chowkath with necessary hinges,screws,bolts etc.as specified and directed at all levels(Door fixtures and fitting to be measured and paid separately) b) 24mm thick

6.2.2 15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to lst floor level including arises, internal rounded angles, not exceeding 8Omm girth and finished even and smooth including curing complete as directed. B) On fair side b) In cement mortar I:4

6.2.2 15mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 8Omm girth and finished even and smooth including curing complete as directed. A) On rough side b) In cement mortar 1:4

6.2.6 Extra over item no 6.2.1 to 6.2.3 for interior plastering above Ist floor level for every addl floor or part thereof including curing complete as directed. a) On Single coat plaster

10.2 Providing, fitting and fixing M.S. Grill of required pattern for windows/ clerestory windows/ opening with M.S. flats at required spacing in frame all round, square or round M.S. Bars with round headed bolts and nuts or screws. 1 Plain grill (b) Fixed to steel frames

1.3 Earth/ sand filling in plinth in layers not more than 150mm thick including necessary carriage, watering, ramming etc. complete as directed and specified including payment of land compensation, forest royalty, sales tax and other duties and taxes as may be necessary. (e) With river sand or silt (predominantly non plastic) by truck carriage including loading and unloading.

26.1.3 Pre construction anti termite treatment by applying in the entire levelled area after plinth filling and before laying floor by applying the emulsion 5 (five) litres per square meter of the surface to be spread with light rodding so as to ensure proper absorption by the filled up earth (supplying of necessary tools and accessories by the contractor) as per the direction of the Department complete. a) with aqueous emulsion having concentration I:19 with chloropirophose solution (tricel or euivalent) and water, ie. 1% solution.

2.1.2 Plain cement concrete floor base in propl:3:6 laid in alternate bays as specified with coarse agg, of size 13mm to 32mm including dewatering if necessary, and curing etc. complete. c) 100mm thick

18.3.2 Providing, fitting, hoisting and fixing of roof trusses fabricated out of combination of any two or all of the following sections (i) Square section (ii) Rectangular Hollow section of specification RSH/SHS and (iii) M.S. circular hlollow section of Grade 210 including purlins, bottom runners and providing M.S. cleat, M.S. angle base plank, bolts and nuts with red oxide primer including fitting bottom runner and cleat etc. for fixing ceiling joist as per design complete as directed as per specifications. b) Using other ISI marked approved brand tube .

8.1.33 Providing Pre Painted Galvanized Iron Sheet Roofing (PPGI) at all levels including fitting and fixing with self drilling, self tapping serews complete. (Roof trusses, purlins etc. to be measued and paid separately) TATA Blue scope/ Dyna roof/ Durakolor Wonder Roof or equivalent as directed by the Departement. (v) 0.55 mm thick

8.1.34 Providing Pre Painted Galvanized Iron Sheet (PPGI) accessories (Ridges / Valley / Gutter /Flashing) at all levels including fitting and fixing self drilling, self tapping screws complete . TATA Blue scope/ Dyna roof / Durakolor /Wonder Roof or equivalent as directed by the Departement (iv) 0.55mm thick

5.7.2.1 VITRIFIED TILES (A) AT FLOOR Providing VITRIFIED floor tiles of approved quality of specified size, shape and thickness not less than 18mm on floors, skirtings, risers and treads of steps over 5 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/ Pedelite/Rouf)/white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) a) Normal range Somany/ Orient/Nitco/ Varmora/WITA/ Marbito/ Make ii) Of size 600mmx600mm and above

5.7.2.2 VIRIFIED TILES B) ON WALLS Providing polishedl vitrifed wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop 1:3 (1 cement:3 coarse sand ) including cutting where necessary finisheed with flush pointing with Fix A Tile (Choksey/Sika/pedelite/Rouf /white cement slurry mixed with approved pigment to match shade of tilec complete at all levels as specified and directed (coloured pigment should be in conformity with colour of tiles and as approved and directed by the department) i) Of size 300mmx45Omm and above

19.2 Providing plinth protection with bricks flat laid in cement mortar 1: 4 and finished with 15mm thick cement plaster in prop. 1:2 with a floating coat of neat cement finish.

19.4 Providing drain with cement conerete (1:3:6)10cm thick sides 1Ocm thick bed over brick flat soiling including 15mm thick cement plastering in prop 1:3 finished with a floating coat of cement slurry as directed with necessary shuttering for sides and earth work in excavation of foundation trenches and refilling the sides after completion of work etc. as specified. (1) 300mm wide and average 150mm deep with bed slope 1 in 150 with initial depth of 100mm.

13.3.4 PLASTER OF PARIS & WALL PUTTY Providing two coats of Birla White Wall Care Putty (Water Resistant White Cement based putty for concrete/ mortar walls and ceiling both internal and external) after removing all loosely adhering material from the wall surface with the help of emery stone. putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department (Total thickness of two coats is maximum 15mm) i) Thickness 1.5 mn thick

WALL PAINTING 13.4.1 Wall painting (two coats) with acrylic emulsion paint approved brand and manufacture (Asian paint/ Berger paint/ lCI paint/ J & N paint/ Nerolac) on new surface to give an even shade after thoroughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth. (a)Acrylic Emulsion Paint approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac)

13.4.2 Extra over item no 13.4.1 above for every subsequent coat of wall painting with acrylic emulsion paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) (a)Acrylic Emulsion Paint approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac)

EXTERIOR PAINTS/ COATINGS 13.5.1. Applying one self-priming coat of acrylie emulsion coating of Unicem 'Rakshak' brand by thinning 1ltrs of paints with 1ltrs of water over freshly plastered wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth as specitied and directed by the department.

13.5.2 Finishing wall with two coats of acrylic emulsion exterior coatings of Unicem 'Rakshak" brand of required shade by thinning 1ltr. of paint with 750ml of water to give an even shade after throughly brooming the surfaces to remove all dirt and remains of loose powdered materials as specilied and directed by the department.

15.2.1 Supplying. fitting, fixing anodised aluminium fittings of approved make, reasonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete (anodised to bright natural matt & satin finished) (a) Sliding door bolts (ii) 250mm x 16mm

(b) Tower bolts (1i) 250mm x 12mm

(c)Door handles (ii) 150mm

SANITARY AND WATER SUPPLY WORK 1.2 Providing fittIng and fixing vitreous china pedestal type water closet (European type W.C pan 400mm high ) with seat and,CP brass hinges and rubber buffers, CI/MS brackets, 40 mm dia flush band with fittings including painting of fittings and brackets, required. (Flushing Cistern to be paid separately) A) Parryware make a) White (i) Universal Closet S Trap (Cat No.C0271) (Anglo Indian) (inclusive of seat cover)

1.5 Supplying, fitüng and fxing PVC flushing cistern with all internal fittings with CI brackets including fitting and fixing standard size CP flush pipe, union clamps etc. compete as directed and specified (pipes will be measured separately) i) Parryware make a) White i) Deluxe Single Flush (Cat. No. C8091/C8057).

1.13.1 Providing vitreous China wash basin with CI/MS brackets, C.P brass chain with plug, PVC waste pipe including paintng of fittings and brackets, cutting and making good the walls wherever required. (Pillar cock, stop cocks, waste coupling are to be paid separately) PEDESTAL BASIN (with pedestal) A) Parryware Make (a) White (i) Qube 600 x 460 (Cat No.C844D/G) (white/coloured)

1.19 Providing fitting and fixing Decorative Mirror complete as directed and specified. A)Parryware Make (b) Size 600mm x 450mm

1.22 Providing, fitting and fixing CP soap tray / soap dish complete as directed and specified. (i) Jaquar Make (b) Queen's (Cat No.AON-7731)

1.24 Providing, fitting and fixing CP towal rail complete as directed and specified. (i) Jaquar Make (b)Continental 300mm for wash basin (Cat No. ACN-1101N)

1.37.1 Supplying, fiting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISI approved including joining fitting and fixing with clamps etc. as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (i) 110mm dia.

1.37 Supplying, fiting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining fiting and fxing etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (i) 110mm dia.

1.37 Supplying fiting and fixing 45degree PVC bend of (Supreme/Prince) or other ISI approved including joining fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specifed. a) In exposed surfaces or in trenches. i) 110mm dia

1.37 Supplying fitting and fixing PVC single 'Y' of (Supreme/Prince) or other ISl approved including joining, fitting and fixing etc as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 110mm dia.

1.51 Construction of filter bed in soak pit including earth work in excavation of soil and then flling up of the trench with brick bats/Charcoal covered with earth overa layer of A.C. plain sheet above brick bat filling complete as directed. (sizes of soak pit may very depending on the sizes and capacites of the septic tank as well as the number of users as mentioned in the table.

1.36 Supplying, fittng and fixing I.S.I marked or similar approved H.C.I pipe including bolts and nuts and other fitings as required and complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. ii) 100mm dia.

Water Supply Works including Stage 5.3.4 Labour for boring hole for inserting tube well pipes through different soil/ rock media including hire charges of drill pipes, scaffolding, tools and plants as necessary and taking out the same and lowering pipes, fittings complete as directed by the Department. i)Bore hole of 75mm diameter

5.3.5 Supplying, ftting and fixing pipes plain/level ended for casing conforming to relevant IS codes of practice including supplying and fiting of tube well accessories, lowering of assembly pipes concentrically in the borehole followed by supplying and packing of pea gravel free from dirt, dust and other foreign materials in the annular space between the borehole and assembly pipes complete as directed by the Department. (I) G.I. pipe a) TATA SAIL (Medium) socket should be welded to the pipes i) 50mm diameter

5.3.7 supplying fitting and fixing GI filter 2.00 metre long

5.3.11 Supplying fitting and fixing check valve (non return valve) including thread to pipes. ii) 40mm diameter

5.3.12 Development of the tube well with compressor or by over pumping unit for 48 hours till sand free discharge is obtained

5.4.2 Supplying and placing ptastic cylindrical vertical claused top (PCVC) tank of Sintex/ Polycon/ Patton make over the stagging with manhole cover with locking and cleaning arrangement including providing pads of size as required for inlet and outlet pipes ii) 1000 Lt capacity (a) Sintex make

5.4.6 Labour for erecting and placing PCVC Tank over the stagging of 5.00m up to 8.00m complete as directed. (c) 1000 litre capacity

3.1.1 Supplying fitting and fixing G.I. Pipes of following sizes, with all necessary 'R' brand or similar approved G.I. Fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fiting, H.W. clamps etc. complete at all levels including below G.L. as directed and specified. (A) Exposed on walls b) 40 mm dia (Medium) i) Using Tata make

d) 25 mm dia (Medium) i) Using Tata make

d) 15 mm dia (Medium) i) Using Tata make

3.2.1 Supplying fiting and fixing C.P. bib cock 15mm dia of approved brand directed and specified. (G.I. & C.P pipes will be measured separately) i) Jaquare make i) Bib-cock long thread

(ii) Jauare make (iii)2-Way bib cock

3.3.1 Supplying fiting and fixing stop-cock of approved brand of size as mentioned below and directed and specified (G.I. & C.P. pipes will be measured and paid separately) I) Brass stop cock (heavy) of Sant make v) 40mm dia

ii) 25mm dia

3.6.1 Supplying fiting and fixing Chrome Plated (C.P.) sink cock of approved brand as directed and specified. (G.I. & C.P pipes will be measured and paid separately) (v) Jaquar brand a) Continental/Clarion i) Sink cock with raised 'J' shaped swinging spout

3.8.2 Supplying fittang and fixing Chrome Plated (C.P.) Shower 15mm dia. Of approved brand as directed and specified. (Pipes will be measured and paid separately) (iii) Jaquar make ii) Shower arm 190mm long heavy casted body with wall flange

3.8.4 Supplying fitting and fixing Telephonic Chrome Plated (C.P.) shower of approved brand as directed and specified. (Pipes will be measured and paid separately) (ii) Lauret make (Telephonic hand shower with 1.5 m PVC pipe with hook)

3.10.1 Supplying, fitting and fixing Chrome Plated (C.P.) wall mixer complete as directed. (v) Jaquar make v) Wall mixer 3 in 1 system with provision for both telephonic shower and overhead shower complete with 115mm long bend pipe Cat No.1119.

3.10.1 Supplying, fitting and fixing Chrome Plated (C.P.) wall mixer complete as directed. (v) Jaquar make v) Wall mixer 3 in 1 system with provision for both telephonic shower and overhead shower complete with 115mm long bend pipe Cat No.1119

6.3.1 Supplying and placing Ferrocement Iron Removal Plant over stagging with movabale G.I. Sheet cover with side ventilation including providing pads of size as required for inlet and outlet pipes complete as directed. (Stagging and storage reservoir should be measured and paid separately). (i)1000 It capacity

INTERNAL APPROACH ROAD 3.14 Construction of Subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 1000m as per Technical Specification Clause 303.1 (i) privet land

4.1 Granular Sub- base with Well Graded Material (Table 400.1) (A) By Mix in place Method Construction of granular sub- base by providing well graded material , spreading in uniform layers by tractor with grading attachment on prepared surface, mixing by mix in place method with rotavator at OMC , and compacting with smooth wheel roller to achieve the desired density, complete as per technical Specification Clause 401. (i) for Grading lI Material

4.7 3) WBM Grading 3 Using stone screening Type - A 13.2 mm for Gr3 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100kN in stages to proper grade and camber, applying and brooming,stone screening to fill up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405. (A) By Manual means

(A) Interlocking pavement block 6.7. i) Providing and laying interlocking concrete block pavement with M40 grade grade of concrete blocks having thickness 80mm as per technical specification clause 1504 complete including carriage. a) Including Edge block /Edge restraints.

EARTH FILLING 1.4. Raising low site around the building with approved soil obtained from outside by truck carriage including breaking clods, dressing etc. complete including paying necessary land compensation, Municipal gate fees, if any monopoly duty etc. (profle measurement to be taken and 12.5% deduction for shrinkage to be made from total quantity) etc.complete as directed and specified, including forest royalty within a distance of 8.00 km. (forest royaity shall be reimbursed on production of necessary certificate from the forest authority duly countersigned by D.F.0. concerned). (b) Other than Guwahati city

ELECTRICAL WORK 2.11 Wiring for light/ fan/ call bell point with 2x1.5 sq. mm PVC. insulated single core unsheathed industrial (Multistrand) cable HFFR/ZHFR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco or Equivalent Make as approved by the Deptt.) in recessed conduit wiring system with 2 mm thick 20mm dia rigid low halogen SFT PVC IS: 9537 Part-III conduit (Berlia/ AKG/ Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) complete 2.11.1 SP upto 3.00 metre length.

2.11.2 MP upto 6.00 metre length.

2.11.3 LP upto 10.00 metre length

2.12 Wiring to 5 a pin 6 Amps plug point with 1.5 sq mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable HFFR/ZHFR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco or Equivalent Make as approved by the Deptt.) in recessed 2 mm thick rigid low halogen SFT PVC IS: 9537 Part II conduit (Berlia/ AKG / Precision/ Presto Plast / polycab/ MW or equivalent make as approved by the Deptt.) wiring system including earth continuity with 1.5 sq. mm. cable to third pin of the plug socket etc. as required complete 2.12.1 SP upto 3.00 metre length.

2.12.2 MP upto 6.00 metre length.

2.12.3 LP upto 10.00 metre length

2.13 Wiring for 5 pin 16 Amps power plug point with 4 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable HFFR/ZHFR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco or Equivalent Make as approved by the Deptt.) in surface/ recessed conduit wiring system including earth continuity with 2.5 sq. mm cable to the 3rd pin of the socket as required complete with 2 mm thick 20 mm. dia. rigid low halogen SFT PVC IS: 9537 Part -III conduit (Berlia/ AKG/ Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) 2.13.1 SP upto 3.00 metre length.

2.13.2 MP upto 6.00 metre length.

2.13.3 LP upto 10.00 metre length

2.6.2 Wiring for circuit wiring with P.V.C insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed PVC conduit (Berlia/ AKG/ Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) wiring system. With 3 x 1.5 sq. mm. cable in 20mm dia 2mm thick/ heavy rigid PVC IS:9537 part-III conduit

2.7 Wiring for drawing sub-main line with P.V.C insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) PVC conduit (Berlia/ AKG/ Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) including earth continuity in surface/ recessed 20mm dia 2mm thick/havey ISI marked IS:9537 PART -III rigid PVC conduit wiring system. 2.7.1 with 2 x 2.5 sq mm + earth continuity with 1 x 1.5 sq. mm in 20 mm dia 2mm thick/havey rigid PVC IS:9537 part-III conduit.

2.7.2 with 2 x 4 sq mm + earth continuity with 1 x 2.5 sq. mm cable in 20 mm dia 2mm thick/havey rigid PVC IS:9537 part-III conduit.

2.7.3 with 2 x 6 sq mm + earth continuity with 1 x 4 sq. mm cable in 25mm dia 2mm thick/havey rigid PVC IS:9537 part-III conduit.

2.9 Wiring for drawing sub-main line with P.V.C insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.)in surfave/recessed PVC 20mm dia 2mm thick/heavy ISI marked IS: 9537 PART-III rigid PVC conduit (Berlia/ AKG/ Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) including wiring system. 2.9.4 with 4 x 10 sq mm + earth continuity with 2 x 6 sq. mm cable in 40mm dia 2mm thick/havey rigid PVC IS:9537 part-III conduit.

2.9.5 with 4 x 16 sq mm + earth continuity with 2 x 10 sq. mm cable in 40mm dia 2mm thick/havey rigid PVC IS:9537 part-III conduit.

B. SWITCH/SOCKET/PLATE ETC. SB8.4 Supplying including installation of socket outlet 10/16 Amps 3/5 pin combine shuttered complete MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE). MK (BLENZE), SCHNEIDER (ZENSELO) CRABTREE(MURANO) including making necessary connection as per direction of department.

SB8.5 Supplying incduding installation of socket outlet 6/10/13 Amps INTERNATIONAL SOCKET. MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO). CRABTREE (MURANO) including making necessary connection as per direction of department.

SB8.7 Supplying with fitting fixing of 16 amp one way modular clip in switch, MODEL RANGE LEGRAND (ARTEOR). ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

SB8.8 Supplying with fitting fixing of 6/10 amp one way modular clip in switch, MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

11/SB8.13 Supplying including and fixing of following Metal boxes for MODEL RANGE LEGRAND (ARTEOR). ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) in surface/ recessed system complete as per direction of department. SB.8.13.4 4 module

SB.8.13.6 6 module

SB.8.13.9 9 module

SB8.14 Supplying including fitting fixing of following MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO),CARBTREE(MURANO) front plate of suitable colour as per direction of department. SB.8.14.4 4 module

SB.8.14.5 6 module

SB.8.14.7 9 module

SB8.18 Supplying with fitting fixing of blank plate single in modular switch system, MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

C. FITTING & FIXTURES. 11.10 Supplying and fixing of Plain Pendent holder (Anchor Penta PC CHERRY /Gold medal /Kolor kany kom/Havells or equivalent make as approved by the Deptt.) with twin twisted flexible cable connection as approved by the Deptt.)as required without lamp.

10. Supplying.installation,testing and Commission of the following indoor surface Mounted LED Luminaires complete with all accessories such as driver etc. and necessary connection with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department. 10.2 Philips lighting luminaire 15W Cirrus Mini Model SM518C LED9S 6500 PSU OD GR/SM518C LED9S 6500 PSU OD WH or equivalent as approved by the Deptt.

11. Supplying, installation,testing and Commission of the following indoor Surface Mounted and Suspended Luminaires LED Luminaires complete with all accessories such as driver etc. and necessary connection with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department. 11.5 Philips 24 W, Astra Surface & wall mounted LED batten Model BN150W LED20S-6500 PSE OD GR or equivalent as approved by the Deptt.

12 Supplying.installation,testing and Commission of the following LED lamp as directed by the department. 12.25 Philips LED bulbs non-dimmable 7 W or equivalent as approved by the Deptt.

11.32 Supplying and fixing of Call bell ( Buzzer) including 5/ 6 amp capacity button piano type bell push switch including connection as approved by the Deptt.)as required.

EARTHING 22.7 Installation of earth station with 4Omm dia and 4.5 mtr. long Gl pipe with necessary GI reducing socket 40mmx20mm size locking arrangement with hinged cover plate, funnel, GI nuts, thorough bolts etc.for putting pipe and refitting with necessary enclosure on the top etc. as required.

22.12 Extra for using salt 5Kg and charcoal 64 Kg. for pipe earth electrode as required.

22.15 Supplying and laying with 6 SWG GI earth wire at 0.50 mtr. below ground level or conductor earth electrode including soldering, excavation work and refitting etc.as required complete.

22.11 Supply, installation & testing of Copper Plate earth station with 600 mm X 600 mm X 6 mm heavy duty copper earth plate with necessary 40 mm dia. G.I medium duty watering pipe with G.I. Fittings such as Socket, Tee, elbow, nipple and 50 mm X 40 mm G.I reducing socket for funnel including locking arrangement with 300 mm X 300 mm X 6 mm C.I. hinged cover plate complete with digging of earth pit, construction of brick chamber and plastering of both inner & outer surface of wall as specified and directed by the deptt.

E.CEILING/EXHAUST FAN ECB1.1 Supplying including fitting fixing of following star rated A.C. Ceiling fan complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connection cable, as approved by the Deptt.s etc. as required complete and as directed by the Department Without regulator). (ORIENT PSPO make/ Usha make/ CROMPTON make/ Havells/ ATC/ V GAURD make). ECB/1.1.1 Energy efficient 5-star 1200 mm sweep. ORIENT PSPO/Usha/ CROMPTON / Havells/ ATC or equivalent make.

27.2 Supplying including fitting fixing of following A.C. Exhaust fan in the existing hole on the wall of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department. 27.2.1.2 Power Flow 225 mm sweep (ORIENT make)

MCB/MCBDB/RCCB ETC. 15.2 Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Double door IP-43 surface mounting SPN MCB DB incorporated with bas-bar, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. 15.2.1 ABB, Schneider MG, legrand, Hager make) 15.2.1.4 12 way SPN double door.

15.20 Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Double door IP-43 double door surface mounting vertical TPN MCB DB incorporated with bas-bar 125A, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. 15.20.1 ABB, Schneider MG, legrand, Hager make) 15.20.1.1 4way TPN (4+12) double door

27/16.1 Supplying with fitting and fixing single Pole 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessay connection as approved, specified and directed by the deptt. 16.1.2 C Series 16.1.2.1 6-32A

16.8 Supplying with fitting and fixing 30/100/300mA sensitivity 240/415V 50Hz 4P RCCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. 16.8.2 100/300mA sensitivity 4P RCCB (ABB, Schneider MG, legrand, Hager make) 16.8.2.2 40A

16.7 Supplying with fitting and fixing 30/100/300mA sensitivity 240/415V 50Hz DP RCCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. 16.7.1 30mA sensitivity DP RCCB 16.7.1.2 40A

16.6 Supplying with fitting and fixing 4P 10 KA 240/415 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 16.6.2 C Series (ABB, Schneider MG, legrand, Hager make) 16.6.2.3 63A

16.23 Supplying with fitting and fixing Four Pole 415V Front handle operated On Load Change over switch (IP-20 protection powder painted sheet steel enclosure fitted on angle iron frame of the following capacity oomplete with making necessary connection as approved, specified and directed by the dept. 16.23.1 ABB. Schneider, legrand, L&T make) 16.23.1.2 100A

H.UG CABLE ETC./BOLLARD LIGHT 32.5 Supply and laying of following size Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up. PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988, LT armoured U.G. cable laid in pucca flooring. road crossing, drain crossing as per site requirement and partially in air to connection as approved by the Depts. the control switch, through medium duty G.I. pipe (Tata/ Nezone make or equivalent as approved by the Deptt) bend and socket including excavation and refilling the trench and making good damage done as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) 32.5.3 Core 3 & 1/2 A2XWY A2XFY 32.5.3.4 70.00 Sq.mm 38&1/2 Core U.G. cable in 5Omm dia medium duty G.1. pipe

32.1 Supply and laying of following size PVC/XLPE insulated and PVC sheathed 1.1 KVG Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip),extruded PVC Type ST2 sheathed, 650/110OV grade as per IS 7908(Part 1)1988 armoured U.G. cable U.G. cable laid in ground/partially in air (as required for termination over ground including excavation of cable trench up to depth of 75cm, refilling. protective brick covering, Sand cushioning etc complete handling of surplus spoil, debris et to proper place as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) 32.1.1 2 Core A2XWaY A2XFaY 32.1.1.1 4.00 Sq.mm 2 Core armoured U.G. cable

FIRE FIGHTING 29.2.10 supply,Installation,fixing of CARBON DIOXIDE fire Exinguisher confirming to IS:2878 with ISI marked (Extinguisher will be TROLLEY MOUNTED) (6.5KG) BRAND:FIRESTOP /FIREND/FIRE SHIELD

29.2.11 supply,Installation,fixing of CARBON DIOXIDE fire Exinguisher confirming to IS:2878 with ISI marked (Extinguisher will be TROLLEY MOUNTED) (9KG) BRAND:FIRESTOP /FIREND/FIRE SHIELD

29.2.9 Supply,Installation,fixing of CARBON DIOXIDE fire Exinguisher confirming to IS:2878 with ISI marked (Extinguisher will be TROLLEY MOUNTED) (4.5KG) BRAND:FIRESTOP /FIREND/FIRE SHIELD

SEPTIC TANK 1.1. Earth work in excavation for foundation trenches of walls, retaining walls, footings of columns,steps and septic tank etc. including refiling (return filling) the quantity as necessary after completing of work, breaking clods in return filling dressing, watering and ramming etc and removal of surplus earth with all lead & lift as directed and specified in followng classification of soils including bailing out water where necessary as directed and specified. (A) Up to depth of 2.0 m below the existing G.L

4.1.1. Providing brick work soiling in foundation and under floor with stone / best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering , complete.

2.1.1. Plain cement concrete works with coarse aggregate of sizes 13mm to 32 mm in foundation bed for footting, steps, walls,brick works etc. as directed and specified including dewatering if necessary, and curing complete (Shuttering works where necessary shall be measured and paid separately.) (a) In prop 1cement : 3 Sand : 6 coarse aggregate by volume. (Using mixture mechine)

18.1.1. Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level). (b) Other ISI approved TMT reinforcement bar (SAI/BISCON/THERMAX). (For Assam Type Bldg., drain works,,retaining wall&boundary wall etc.)

3.2.1. Providing form work of 12mm thick Plywood Board so as to give a rough finish including centering, shattering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in situ reinforced concrete and plain concrete work in: 2. Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties. (a) For depth not exceeding 1.0M

3. Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like. (a) Floors etc. upto 200mm in thickness.

2.2.1 Providing & laying reinforcement cement concrete works in prop 1:2:4 ( 1 cement : 2 coarse sand : 4 coarse aggregate 20mm down) including dewatering if necessary and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work. (form work and reinforcement will be measured and paid separately) (a) In Sub-Structure up to plinth level Foundation, footings, columns with base, tie & plinth beam, pile cap,base slab,r etaining walls, walls of the septic tank inspection pit and the like and other works not less than 100mm thick up to plinth level. a) M15 or Prop. 1:2:4

4.1.4. Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed. (I) In Sub-structure upto plinth level including dewatering if necessary (a) In proportion 1:3.

4.1.8 1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separately) (A) 112mm thick brick wall (a) In cement mortar in proportion 1:4. (1 cement:4 sand)

6.2.2 15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. B) On fair side (b) In cement mortar 1:4

6.2.4 Extra over item no 6.2.1 to 6.2.3 for providing and mixing water proofing materials in cement mortar in prop as recommended by the manufacturer including curing complete as directed. ii) 15 mm thick plaster b) In cement mortar 1:4

5.1.10 Cement plaster skirting with cement mortar in prop. 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement including rounding of junctions with floor. (a) 15mm thick.

1.47 Providing fitting and fixing 450mm dia. 90mm thick C.I. Man hole cover and frame of 38 Kg. weight complete as directed and specified.

Bibhuti Goyari