Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹5.9 LAccepted-AOC 1001 63 SHALIMAR GARDEN ISMAILGANJ NEAR INDIRA NAGAR SECTOR 08 CROSSING LUCKNOW 226016 | LUCKNOW | UTTAR PRADESH | 226016 | L1 | Accepted-AOC Being the lowest tenderer and fulfilling all the criteria | |
| 2 | L2₹7.5 L+₹1.7 L (28.3%)Rejected-Finance | L2 | Rejected-Finance Not being the lowest tenderer | |
| 3 | L3₹7.7 L+₹1.8 L (30.3%)Rejected-Finance 63 2ND MAIN ROAD NGO COLONY ADAMBAKKAM CHENNAI 600 088 | CHENNAI | CHENNAI | TAMIL NADU | 600088 | L3 | Rejected-Finance Not being the lowest tenderer | |
| 4 | Rejected-Technical OLD NO 338 NEW NO 17 19TH NEDUMANEHLIAN STREET G K M COLONY CHENNAI 600 082 | CHENNAI | CHENNAI | TAMIL NADU | 600082 | - | Rejected-Technical Contractor is not fulfilling the liad down criteria |
Tender Value
₹10 L
EMD Value
₹20,000
Closing Date
24 Jul 2020, 6:00 pmClosed
GARRISON ENGINEER, GE CHENNAI
GARRISON ENGINEER, FORT ST GEORGE CHENNAI
REPAIRS/ MAINTENANCE OF PUMP SETS AT ZONE A B AND D AREA UNDER GE CHENNAI
2020_MES_355882_1
8449/E8
Open Tender
Civil Works
Item Rate
270 days
GE Chennai
As per tender document
7 documents required · 7 mandatory
₹500
GE Chennai
₹20,000
Yes
22 Sept 2020
25 Jun 2020
30 Jul 2020
25 Jun 2020
24 Jul 2020
3 Jul 2020
Amount
Dismantling inlet and outlet pipe, electrical connection, taking out complete electric driven Centrifugal / mono block pump set of capacity 2 to 7.5 HP, 3 phase, 415 volts, 50Hz with suction and delivery lines of any size, shifting to civil work shop for carrying out repair / overhauling including replacement of worn-out spares and bringing back after repair, refixing, testing, commissioning etc., complete all as specified and directed. Make: Kirloskar/ Crompton/ Jyoti/ Suguna. Note:- Cost of spares alone shall be measured and paid separately.
Dismantling of electric motor of capacity 2.0 HP, cutting and taking out burnt/ unserviceable winding coils, cleaning of slots and rewinding with correct size/ gauge super enameled insulated copper wire including providing proper insulation, varnishing, drying, reassembling etc., complete all as specified and directed.
Supply only following spares for 2.0HP capacity electric driven pump set:-
(a) Ball bearings (drive end/ non drive end).
(b) Terminal Box.
(c) Terminal connector 3 phase
(d) Electro dynamically balanced bronze impeller.
(e) Gun metal bush
(f) Gland cup with bolts and nuts.
(g) Flange drilled of suitable size with bolts and nuts including rubber gasket.
(h) Rotor
Dismantling of electric motor of capacity 3.0 HP, cutting and taking out burnt/ unserviceable winding coils, cleaning of slots and rewinding with correct size/ gauge super enamelled insulated copper wire including providing proper insulation, varnishing, drying, reassembling etc., complete all as specified and directed.
Supply only following spares for 3.0HP capacity electric driven pump set:-
(a) Ball bearings (drive/ non drive)
(b) Cooling fan blade PVC.
(c) Terminal Box.
(d) Terminal connectors 3 phase.
(e) Supply only electro dynamically balanced bronze impeller
(f) Shaft (Mild steel)
(g) Gun metal bush
(h) Gland cup with bolts and nuts.
(j) Water seal.
(k) Flange drilled suitable size with bolts, nuts and rubber gasket.
(l) Air cock nozzle brass
(m) Shaft coupling.
(n) Rotor
Dismantling of electric motor of capacity 5.0 HP, cutting and taking out burnt/ unserviceable winding coils, cleaning of slots and rewinding with correct size/ gauge super enameled insulated copper wire including providing proper insulation, varnishing, drying, reassembling etc., complete all as specified and directed.
Supply only following spares for 5.0HP capacity electric driven pump set:-
(a) Ball bearings (drive/ non drive).
(b) Cooling fan blade PVC.
(c) Terminal Box.
(d) Terminal connector 3 Phase.
(e) Shaft Metal Bush.
(f) Gun metal bush
(g) Gland cup with bolt and nuts.
(h) GI flange drilled suitable size with bolts, nuts and rubber gasket.
(j) Air cock nozzle brass.
(k) Electro dynamically balanced bronze impeller.
(l) Rotor
Dismantling of electric motor of capacity 7.5 HP, cutting and taking out burnt/ unserviceable winding coils, cleaning of slots and rewinding with correct size/ gauge super enameled insulated copper wire including providing proper insulation, varnishing, drying, reassembling etc., complete all as specified and directed.
Supply only following spares for 7.5HP capacity electric driven pump set:-
(a) Ball bearings (drive end/ non drive end)
(b) Cooling fan blade PVC.
(c) Terminal connector with terminal box.
(d) Electro dynamically balanced bronze impeller
(e) Gun metal bush.
(f) Gland cup with bolt and nuts.
(g) Sleeves (stainless steel)
(h) Rotor
Dismantling inlet and out let pipe, Electrical connection, taking out complete electric driven Centrifugal/ mono block pump set of capacity 10 to 30HP, 3 phase, 415 volts, 50Hz with suction and delivery lines of any size, shifting to civil work shop for carrying out repair/ overhauling including replacement of worn-out spares and bringing back after repair, refixing, testing, commissioning etc., complete all as specified and directed. Make: Kirloskar / Crompton / Jyoti / Suguna. Note:- Spares shall be measured and paid separately.
Dismantling of electric motor of capacity 10 HP, cutting and taking out burnt / unserviceable winding coils, cleaning of slots and rewinding with correct size / gauge super enameled insulated copper wire including providing proper insulation, varnishing, drying, reassembling etc., complete all as specified and directed.
Supply only following spares for 10 HP capacity electric driven pump set:-
(a) Ball bearings (drive end/non drive end).
(b) Cooling fan blade PVC.
(c) Terminal connector with terminal box.
(d) Electro dynamically balanced bronze impeller`
(e) Gun metal bush.
(f) Gland cup with bolt and nuts.
(g) GI flange drilled suitable size with bolts, nuts and rubber gasket.
(h) Cooling fan cover with screw.
(j) Rotor
Dismantling of electric motor of capacity 12.5 to 15 HP, cutting and taking out burnt/ unserviceable winding coils, cleaning of slots and rewinding with correct size/ gauge super enameled insulated copper wire including providing proper insulation, varnishing, drying, reassembling etc., complete all as specified and directed.
Supply only following spares for 12.5 to 15 HP capacity electric driven pump set:-
(a) Ball bearings (drive end/ non drive end).
(b) Cooling fan blade PVC.
(c) Terminal connector with terminal box.
(d) Electro dynamically balanced bronze impeller`
(e) Gun metal bush.
(f) Gland cup with bolt and nuts.
(g) GI flange drilled suitable size with bolts, nuts and rubber gasket.
(h) Cooling fan cover with screw.
(j) Rotor
Dismantling of electric motor of capacity 20 HP cutting and taking out burnt/ unserviceable winding coils, cleaning of slots and rewinding with correct size/ gauge super enameled insulated copper wire including providing proper insulation, varnishing, drying, reassembling etc. complete all as specified and directed.
Supply only following spares for 20 HP capacity electric driven pump set:-
(a) Ball bearings (drive end/non drive end)
(b) Shaft (Mild steel).
(c) Shaft sleeves (stainless steel)
(d) Rubber deflector.
(e) Impeller lock nut.
(f) Impeller key.
(g) Shaft coupling.
(h) Cooling fan cover with screw.
(j) Gun metal impeller.
(k) Air cock nozzle (Brass).
(l) Eye bolts with steel washer.
(m) Rotor
Dismantling of electric motor of capacity 30 HP cutting and taking out burnt/ unserviceable winding coils, cleaning of slots and rewinding with correct size/ gauge super enameled insulated copper wire including providing proper insulation, varnishing, drying, reassembling etc. complete all as specified and directed.
Supply only following spares for 30 HP capacity electric driven pump set:-
(a) Roller bearings No. 313 driving end.
(b) Ball bearing no. 6312 driving end.
(c) Pump shaft
(d) Glang sleeve
(e) Hook bolts & nuts.
(f) Bearing lock nut.
(g) Electro dynamically balanced bronze impeller.
(h) Shaft pin.
Dismantling inlet and out let pipe, Electrical connection, taking out complete electric driven Centrifugal/ mono block pump set of capacity 0.5 to 1 HP, 3 phase, 415 volts, 50Hz with suction and delivery lines of any size, shifting to civil work shop for carrying out repair/ overhauling including replacement of worn-out spares and bringing back after repair, refixing, testing, commissioning etc., complete all as specified and directed. Make: Kirloskar/ Crompton/ Jyoti/ Suguna. Note:-Spares shall be measured and paid separately.
Dismantling of electric motor of capacity upto 1 HP, cutting and taking out burnt/ unserviceable winding coils, cleaning of slots and rewinding with correct size/ gauge super enameled insulated copper wire including providing proper insulation, varnishing, drying, reassembling etc., complete all as specified and directed. Note:-Spares shall be measured and paid separately.
Supply only following spares for 0.5 to 1 HP capacity electric driven pump set:-
(a) Ball bearings (drive end/ non drive end).
(b) Electro dynamically balanced bronze impeller
(c) Terminal connector with terminal box
(d) Water seal.
(e) Condenser of capacity 140/ 160 MFD.
Preparation of old painted surface and cleaning the surface thoroughly and applying two coats of synthetic enamel paint with spray gun and writing the SM/ MES No. for electric driven centrifugal pump and motor set of following capacities of any make complete all as specified and directed:-
(a) Upto 10 HP.
(b) 11 HP to 30 HP.
M&L taking down the existing unserviceable foot valve suitable for 100mm bore pipe and supply and fix new foot valve cast iron body with flanged and leather diaphram, brass spindle, including replacement of bolts, nuts gaskets etc complete all as specified and directed.
M&L taking down the existing unserviceable foot valve suitable for 80mm bore pipe and supply and fix new foot valve gun metal body with flanged and leather diaphram, brass spindle, including replacement of bolts, nuts gaskets etc complete all as specified and directed.
All as per item No. 24.00 above but for 50mm bore pipe.
All as per item No. 24.00 above but for 40mm bore pipe.
Dismantling/ taking down unserviceable and supply and fix new gun metal non return valve suitable to fix on CI/ GI pipe of following sizes, both ends flanged including making alterations of existing pipes etc., complete and testing after completion all as specified and directed:-
(a) 100mm dia
(b) 80mm dia
(c) 50mm dia
Taking out the vertical/ horizontal submersible pumpset upto 20 HP from bore well by using tripod/ puller, flushing the bore well till clear water comes out by using compressor and refixing the submersible pump set into the bore well after carrying out repairs/ overhauling including replacement of worn out spares and bringing back after repair refixing, testing, commissioning etc, complete all as specified and directed.
Dismantling horizontal/ vertical submersible motor upto 10 HP 3 Phase, 415 V, removing the burnt winding wires, cleaning the slots and rewind the stator with super enamelled copper winding wire of the same gauge, reassembling the motor complete after replacing the following items:- (a) Motor gun metal bush - 02 No. (b) Thrust bearing - 01 No. (c) Stud bolts - 04 No.
Dismantling horizontal/ vertical submersible motor 12.5 HP 3 Phase, 415 V, removing the burnt winding wires, cleaning the slots and rewind the stator with super enamelled copper winding wire of the same gauge, reassembling the motor complete after replacing the following items:- (a) Motor gun metal bush - 02 No. (b) Thrust bearing - 01 No. (c) Stud bolts - 04 No.
Supply only stainless steel bolts for upto 20 HP submersible pump set complete all as specified and directed.
Supply only key for any capacity for submersible pump set complete all as specified and directed.
Supply and fix gland rope of any size after removing out old unserviceable one complete all as specified and directed.
Supply and fix rubber coupling suitable for upto 20 HP motor including taking out old unserviceable one complete all as specified and directed.
Taking down the existing pressure guage and Supply and fix new pressure guage 0 - 10 Kg/ sqcm including drilling and tapping of GI pipe of any size for inserting pressure gauge complete all as specified and directed.
Supply, install, testing and commissioning of Pressure vessel with bladder suitable for capacitor start mono block pressure pump upto 1 HP capacity including taking down the existing unserviceable one complete all as specified and directed.
Supply, install, testing and commissioning of Electronic controlling device suitable for capacitor start mono block pressure pump upto 1 HP capacity including taking down the existing unserviceable one complete all as specified and directed.
Dismantling the Electronic controlling device of capacitor start monobloc pump sets upto 1 HP capacity, carryout service, resetting, adjusting, refixing in position, testing and commissioning etc., complete all as specified and directed.
Supply and lay in trenches 100mm bore GI tubing medium grade with screw, socket joints with all fittings/ fixtures like bends, sockets, unions nipples etc. including making alterations in existing/ new pipes complete all as specified and directed.
All as per item No. 39 above but 80mm dia GI tubing.
All as per item No. 39 above but 50mm dia GI tubing.
All as per item No. 39 above but 40mm dia GI tubing.
All as per item No. 39 above but 25mm dia GI tubing.
Supply and fix electronic automatic phase sequence corrector suitable for various HP star-delta starter including taking down the existing unserviceable one complete all as specified and directed.
Taking down the existing unserviceable over load protector relay and replace with new overload relay, range 6 - 39 Amps complete all as specified and directed.
Supply and fix single phasing preventer to various HP suitable for star delta starter including taking down the existing unserviceable kit complete all as specified and directed.
Taking down the existing unserviceable contactor and replace with new contactor suitable for MK-1 starter complete all as specified and directed.
Taking down the existing unserviceable timer and replace with new Timer suitable for ML-1 star delta starter complete all as specified and directed.
Taking down the existing unserviceable No. volt coil and replace with new No volt coil suitable for ML-1 star delta starter complete all as specified and directed.
Supply and fix DOL starter 3 phase 440 volts with relay range upto 16 amps including taking down the existing unserviceable one complete all as specified and directed.
Supply and fix star delta starter with single phase protection and relay range from 13-32 amps 3 phase 440 volts including taking down the existing unserviceable starter complete all as specified and directed.
De-silting of the borewell upto 160 feet deep through compressed air cleaning thoroughly by flushing out water complete all as specified and directed.
Supply and fix MCB, 4 pole, 415 volts, 3 phase, 50 c/s, 63 Amps capacity including taking down the existing unserviceable one complete all as specified and directed.
Supply and fix MCB SP 16 Amps 230 V, AC including taking down the existing unserviceable one complete all as specified and directed.
Supply and fix ammeter AC 0-60/ AC 0 - 100 amps with CT coil including taking down the existing unserviceable one complete all as specified and directed.
Supply and fix voltmeter 0-500 volts AC 3 phase AC 50 HZ including taking down the existing unserviceable one complete all as specified and directed.
Supply and fix MCB SPN 40 Amps AC 240 volts including taking down the existing unserviceable one complete all as specified and directed.
Supply and fix indicating lamp for 3 phase with neon bulbs complete all as specified and directed.
M&L for structural steel work as in base plates for pump sets, bolts, nuts in any situation, valve chamber covers and similar items including taking down the existing unserviceable items complete all as specified and directed.
Taking down the existing unserviceable Nylon mesh and supply and fix new Nylon mesh heavy grade clamped on vent pipe on UG sump/ Well with MS clamp 20mm x 3mm with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.
Supply and fix PVC flexible, heavy duty hose pipe 50mm dia suitable for pumping of water complete all as specified and directed.
Supply and fix PVC flexible, heavy duty hose pipe 80mm dia suitable for pumping of water complete all as specified and directed.
Supply and fix PVC flexible, heavy duty hose pipe 100mm dia suitable for pumping of water complete all as specified and directed.
Supply and fix PVC flexible, heavy duty hose pipe 150mm dia suitable for pumping of water complete all as specified and directed.
Surface dressing not exceeding 15cm deep and getting out in soft/ loose soil complete all as specified and directed.
Excavating in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation or for shafts, wells, cesspit, manholes etc., n.exc 10sqm on plan and getting out in soft/ loose soil complete all as specified and as directed.
Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm soils all as specified and directed.
Removing surplus excavated soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.
Earthing complete with galvanized steel earth plate electrode of size 600mm x 600mm, 6.0mm thick burried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of plate not less than 1.5m below normal ground level, earth plate connected to galvanized iron earth wire of 4mm dia as earthing conductor by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of MES SSR part I (2009) connected to earth test point/ main switch/ DB/ Panel board all as specified or indicated including testing on completion with and including 15mm bore light grade GI protection pipe 7.5 meter long for earth strip including PCC 1:3:6, type C1 pit with precast RCC 1:2:4, type B -1 cover, 40mm thick reinforced with 12mm dia MS bars @ 150 mm c/c both ways with lifting hooks made out of 12mm dia MS bars, wire mesh funnel with watering pipe 20mm dia light grade, common salt, charcoal filling in layers as specified, necessary excavation and earth work in any type of soil etc., complete all as specified and as directed.
SARAVANA ENTERPRISES
EVEREST ENGINEERING WORKS
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.PDF
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .